Viking Installation Guide
®
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking Web site at
vikingrange.com
F20508C EN
Professional Freestanding
30” Electric Range
(112508J)
Table of Contents
IMPORTANT–Read and Follow!
Warnings & Important Safety Instructions _______________________________________________3
Dimensions _________________________________________________________________________4
Specifications _______________________________________________________________________5
Clearance Dimensions (Proximity to Cabinets) ___________________________________________6
Clearance Dimensions (Wood/Composite Overlay) ______________________________________7
Electrical Requirements ______________________________________________________________8
General Information__________________________________________________________________9
Installation _________________________________________________________________________10
Door Removal ______________________________________________________________10
Leg Installation______________________________________________________________11
Electrical Connection (3-wire) _________________________________________________12
Electrical Connection (4-wire) _________________________________________________14
Leveling/Adjustments/Alignment ______________________________________________16
Anti-tip Device Installation____________________________________________________17
Final Installation _____________________________________________________________18
Door Replacement and Adjustment ___________________________________________20
Final Preparation ___________________________________________________________________21
Performance Checklist ______________________________________________________________21
Service & Registration_______________________________________________________________22
• Before beginning, please read these
instructions completely and carefully.
• The installer must leave these instructions
with the consumer who should retain for
local inspector’s use and for future reference.
Your safety and the safety of others is
very important.
In Canada: Installation must be in accordance
with the current CSA C22.1 Canadian
Electrical Codes Part 1 and/or local codes.
We have provided many important safety
messages in this manual and on your
appliance. Always read and obey all
safety messages.
DANGER
This is the safety alert symbol. This
symbol alerts you to hazards that
can kill or hurt you and others.
Electrical shock hazard.
To avoid risk of electrical shock,
personal injury or death; verify
your appliance has been
properly grounded in accordance with
local codes or in absence of codes, with
the National Electrical Code (NEC).
ANSI/NFPA 70-latest edition.
All safety messages will be preceded by
the safety alert symbol and the word
“DANGER,” “WARNING” or “CAUTION.”
These words mean:
DANGER
Hazards or unsafe practices
which WILL result in severe personal
injury or death
WARNING
Moving hazard.
To avoid risk of severe
personal injury; this appliance
requires two or more personnel while
handling and moving. Possible use of
appliance moving devices is recommended.
WARNING
Hazards or unsafe practices
which COULD result in severe personal
injury or death
CAUTION
Hazards or unsafe practices which
COULD result in minor personal injury or
property damage.
WARNING
Tipping hazard.
To reduce the risk of the
appliance tipping, it must be
secured by a properly installed
anti-tip bracket(s). To make sure
the bracket has been installed
properly, look behind the range
with a flashlight to verify proper
installation engaged in the rear
top left corner of the range.
• THIS RANGE CAN TIP.
• INJURIES TO PERSONS CAN RESULT.
• INSTALL ANTI-TIP DEVICE PACKED
WITH RANGE.
• SEE INSTALLATION INSTRUCTIONS.
All safety messages will identify the
hazard, tell you how to reduce the chance
of injury, and tell you what can happen if
the instructions are not followed.
• Do not remove permanently affixed labels,
warnings, or plates from product. This may
void the warranty.
• All local and national codes and ordinances
must be observed. Installation must
conform with local codes.
2
3
Specifications
Dimensions
Electric 30” Range
Electric 30” Range
29
Description
VESC530-4B
Overall width
29-7/8” (75.9 cm)
Overall height
To top of glass frame
35-7/8” (91.1 cm) min.
37” (94.0 cm) max.
Legs adjust 1-1/8” (2.9 cm)
(75-7/8
.9 ”
cm
)
Overall depth from
rear
(20 8”
.3
cm
)
Additions to base
height
*
Electrical
requirements
28-1/16” (71.2 cm)
1-5/8”
(4.1 cm)
3
(91 5-7
.1 /8”
cm
)
to min
.
(94 37”
cm
)m
ax
.
26-7/16” (67.2 cm)
8”
(20.3 cm)
8-1/8”
(20.6 cm)
35-7/8”
(20.3 cm) min.
to
37”
(94 cm) max.
19-3/8”
25-3/4” (65.4 cm)
(49.2 cm)
45-1/8” (114.6 cm)
24-5/16” (61.8 cm)
To
To
To
To
end of side panel—24-5/16” (61.8 cm)
front of door—25-3/4” (65.4 cm)
end of landing ledge—28-1/16” (71.3 cm)
end of door handle—28-11/16” (72.9 cm)
To top of island trim—add 1-1/4” (3.2 cm)
To top of backguard—add 8” (20.3 cm)
To top of high-shelf—add 23-1/2” (59.7 cm)
240-208 VAC, 60 Hz electrical connection box on product, connect with locally
supplied 3-wire, flexible cord or “pigtail” rated 60 amp 125-250 VAC minimum.
Cord must be agency approved for use with household electric ranges.
Maximum amp usage
240V—59.0 amps
208V—51.3 amps
Surface element rating
Left front
Left rear (dual element)
Right front
Bridge
Right rear
1,500 watts
2,500 watts/1000 watts
1,800 watts
800 watts
1,800 watts
Oven interior width
25-5/16” (64.6 cm)
Oven interior height
16-1/2” (41.9 cm)
Oven interior depth
AHAM 16-13/16” (42.7 cm) Overall—19-1/2” (49.5 cm)
Oven volume
Total oven capacity—4.7 cu. ft.
Measure to AHAM standards 4.1 cu. ft.
Approximate
shipping weight
426 lbs. (193.2 kg)
Minimum clearances from adjacent combustible construction
• Cooking surface and below, i.e., 36” (91.4 cm) and below
o Sides—0”
o Rear—0” with backguard or highshelf;0” with island trim and noncombustible rear wall; 6” (15.2 cm) with island
trim and combustible rear wall.
• Above cooking surface, i.e. above 36" (91.4 cm)
o Sides—6” (15.2 cm)
o Within 6” (15.2 cm) side clearance, wall cabinets no deeper than 13” (33.0 cm) must be minimum 18” (45.7 cm)
above cooking surface.
o Wall cabinets directly above product must be minimum 36” (91.4 cm) for open top burners above cooking surface.
*Note: Unit shown with standard 8” (20.3 cm) backguard.
4
5
Clearance Dimensions
• Wall cabinets above the range must be a
minimum of 42” (106.7 cm) above the
range cooking surface for the full width
of the range. This minimum height
requirement does not apply if a range
hood is installed over the cooking surface.
• This range may be installed directly
adjacent to existing 36” (91.4 cm) high
base cabinets.
IMPORTANT: The side trim MUST be
3/8” (.95 cm) above the adjacent base
cabinet countertop. This can be
accomplished by raising the unit using
the adjustment spindles on the legs.
The bottom of a standard hood should be
30” (76.2 cm) min. to 36” (91.4 cm) max.
above the countertop. This would typically
result in the bottom of the hood being
66” (167.6 cm) to 72” (182.9 cm) above the
floor. Refer to the range hood installation
instructions for additional information. These
dimensions provide for safe and efficient
operation of the hood.
Wo
od
/Co
Ov mpo
erl sit
ay e
”
24 cm)
.0
(61 or
66
(16 ”mi
7.6 n.
c
to m)
• The range CANNOT be installed
directly adjacent to sidewalls, tall
cabinets, tall appliances, or other
side vertical surfaces above 36”
(91.4 cm) high. There must be a
minimum of 6” (15.2 cm) side
clearance from the range to such
combustible surfaces above the
36” (91.4 cm) counter height.
• Within the 6” (15.2 cm) side
clearance to combustible vertical
surfaces above 36” (91.4 cm), the
maximum wall cabinet depth
must be 13” (33.0 cm) and wall
cabinets within this 6” (15.2 cm)
side clearance must be 18”
(45.7 cm) above the 36”
(91.4 cm) high countertop.
Clearance Dimensions (Wood/Composite Overlay)
(Proximity to Cabinets)
”
27 cm)
.6
(38
72
(18 ”ma
2.9 x.
cm
)
29
(75-7/8
.9 ”
cm
)
x.
a
m
)
” cm
3
1 3.0
(3
in.
” mcm)
2
4 .7
6”
06
(15 min (1
.2 .
cm
)
”
36 cm)
.4
(91
0” )
m
c
(0
30
(76”min
.2 .
cm
36 to )
”
m
(91 a
.4 x.
cm
)
Wo
od
/Co
Ov mpo
erl sit
ay e
in.
” mcm)
8
1 7
”
3/8 m)
(45
.
c
95
(0.
”
30 cm)
66
.2
(76
72
6” m)
.2 c
5
(1
(16 ”mi
7.6 n.
c
to m)
(18 ”ma
2.9 x.
cm
)
Wall Installation
30
(76”min
.2 .
cm
3 6 to )
”
(91 ma
.4 x.
cm
)
Note: Minimum clearance for back wall
is 0” with backguard or high-shelf.
CAUTION
Burn hazard.
To avoid risk of personal injury;
the use of cabinets for storage
above the appliance may result
in a potential burn hazard. Combustible
items may ignite, metallic items may
become hot and cause burns. If a cabinet
storage is to be provided the risk can be
reduced by installing a rangehood that
projects horizontally a minimum 5” (12.7 cm)
beyond the bottom of cabinets.
Note: Minimum clearance for back wall is 0” with
backguard or high-shelf.
Note: If a range hood is installed, wall cabinets
above the range have a different minimum
clearance height.
6
Note: 6” (15.2 cm) min. with island trim and
combustible rear wall. 0” with island trim
and non-combustible rear wall.
Island Installation
7
Electrical Requirements
Electrical Requirements
General Information
WARNING
Check your national and local codes
regarding this unit. This range requires
3 wire or 4 wire, 240-208 VAC/60 Hz. See
“Electrical Connection” section for
grounding instructions. Must be fused
seperately from any other circuit.
Electrical shock hazard.
To avoid the risk of electrical
shock, personal injury or death;
verify electrical power is turned
off at the breaker box until the range is
installed and ready to operate, installation
by an authorized installer only.
READ AND FOLLOW ALL WARNING
AND CAUTION INFORMATION WHEN
INSTALLING THIS APPLIANCE.
Moving, Handling, and Unpacking
Remove and discard all packing materials,
including cardboard and tape on the outside
and inside of the range.
• All openings in the wall behind the
appliance and in the floor under the
appliance must be sealed.
Range – Do not discard the anti-tip
metal bracket supplied with the
range. This is the anti-tip device and
must be installed with the unit. Refer
to “Anti-tip Device Installation”
section.
• DO NOT obstruct the flow of combustion
and ventilation air.
Electric 30” Range
Some stainless steel parts may have a plastic
protective wrap which must be peeled off.
The interior should be washed thoroughly
with hot, soapy water to remove film
residues and any dust or debris before being
used, then rinsed and wiped dry. Solutions
stronger than soap and water are rarely
needed.
Electrical
connection
in this area
6”
6”
(15.2 cm)
(15.2 cm)
4-3/8”
(11.1 cm)
8
9
DANGER
Leg Installation
Installation
2
1
CAUTION
To avoid risk of personal injury or product
damages, DO NOT use the handle or
oven door to lift the oven. Remove door
before installation to ensure that it is not
used to lift the unit. DO NOT lift or carry
the door by the handle.
1
1
3
Removing the door must be done by your
dealer, or a qualified licensed plumber.
2
2
Note: It is strongly recommended
that a pallet or lift jack be used rather than tilting.
Raise unit about a foot. Unscrew temporary legs from
couplings on all four corners.
Legs are packed in styrofoam top pack.
Note: Legs should be installed near to where
appliance is to be used, as they are
not secure for long transit.
Door Removal
1FOR YOUR SAFETY
2
Open door completely. Place pins,
supplied with unit, in pin hole. For personal safety,
ONLY use pins supplied with the unit.
Remove hinge trim screws. Take off hinge trim. Identify
right and left hinge for future re-installation.
3
4
3
Screw legs into couplings on all
four corners.
Lower range gently to keep any undue strain from
legs and internal mounting hardware.
4
Close until pins stop door.
Lift door up and out.
10
11
Electrical Connection (3-wire)
Note: If you have a 4-wire connection, see following section for
4-wire connection instructions.
WARNING
5
4
WARNING
Electrical shock hazard.
Electrical shock hazard.
To avoid risk of electrical shock,
personal injury or death; verify
your appliance has been
properly grounded in accordance with
local codes or in absence of codes, with
the National Electrical Code (NEC).
ANSI/NFPA 70-latest edition.
To avoid risk or electrical
shock, personal injury or death;
grounding product to the frame
of the unit may or may not be permitted
through your local codes. If ground to the
frame is not permitted then a 4 conductor
power cord must be used.
1
2
3
Push supply cord toward terminal
block to relieve strain, reattach supply cord strain
relief bracket over supply cord.
Attach line #1 (red) and line #2 (black)
leads to outside terminal. Attach neutral wire (white)
to center terminal on the terminal block.
6
1
1
Use a 3-wire power supply cord kit rated for
60 amps – 125/250 volts with closed loop
terminals and marked for use with ranges.
2
DO NOT use a GFI circuit. Where local
codes do not permit grounding through
neutral, use a 4-wire power supply cord. The
cord or conduit must be secured to the
range with the strain relief bracket.
1
The electrical connection is made at the
terminal block, which is located behind the
access door on the back of the range.
2
Remove access door.
Reattach access door.
3
2
3
1
1
2
Remove supply cord strain relief
bracket and three supply cord mounting screws
on terminal block.
Feed supply cord up through hole in bottom
of range back.
12
13
Electrical Connection (4-wire)
5
4
WARNING
WARNING
Electrical shock hazard.
Electrical shock hazard.
To avoid risk of electrical shock,
personal injury or death; verify
your appliance has been
properly grounded in accordance with
local codes or in absence of codes, with
the National Electrical Code (NEC).
ANSI/NFPA 70-latest edition.
To avoid risk or electrical
shock, personal injury or death;
grounding product to the frame
of the unit may or may not be permitted
through your local codes. If ground to the
frame is not permitted then a 4 conductor
power cord must be used.
Use a 4-wire power supply cord kit rated for
60 amps – 125/250 volts with closed loop
terminals and marked for use with ranges.
1
2
Feed supply cord up through hole in bottom
of range back.
Attach ground lead (green)
with ground screw that was removed.
6
1
7
1
2
DO NOT use a GFI circuit. Where local
codes do not permit grounding through
neutral, use a 4-wire power supply cord. The
cord or conduit must be secured to the
range with the strain relief bracket.
1
2
1
The electrical connection is made at the
terminal block, which is located behind the
access door on the back of the range.
Remove access door.
3
2
3
Attach line #1 (red) and line #2 (black)
leads to outside terminal. Attach neutral wire (white)
to center terminal on terminal block.
Push supply cord toward terminal
block to relieve strain, reattach supply cord strain
relief bracket over supply cord.
8
1
3
1
2
1
2
Remove supply cord strain relief
bracket and three supply cord mounting screws
on the terminal block.
2
Remove grounding screw. Cut-off
and discard ground strap.
14
Reattach access door.
15
Leveling/Adjustments/Alignment
2
1
Measure the four corners in cutout area to
verify if flooring is level.
7
For uneven or sloped floors, level unit with
metal shims only, as the adjustment required may
exceed the thread available in the leg.
Set the high corner of range so that the top of side trim is
3/8” (0.95 cm) above countertop. Level range to high corner.
Anti-tip Device Installation
4
3
Tipping hazard.
”
3/8cm)
95
(0.
Check that unit is level side to
side and front to back. Side trim of the high corner
must be 3/8” (0.95 cm) above countertop.
Move unit into opening.
6
5
1
WARNING
•
•
•
•
To reduce the risk of the appliance
tipping, it must be secured by a
properly installed anti-tip bracket(s).
To make sure the bracket has been
installed properly, look behind the
range with a flashlight to verify
proper installation engaged in the
rear top left corner of the range.
THIS RANGE CAN TIP.
INJURIES TO PERSONS CAN RESULT.
INSTALL ANTI-TIP DEVICE PACKED
WITH RANGE.
SEE INSTALLATION INSTRUCTIONS.
2
(A
)
Measure from floor to bottom
of the anit-tip opening located on the back of range.
This will be measurement (A).
3
3-5
(9. /8”
2
cm
)
1
1
+1
)
)
(A .3 cm
1
(
/2”
2
If leveling is required, move unit out of opening.
Lift unit and prop on wood blocks.
16
Locate anti-tip bracket on rear wall with the top left corner at
measurement (A) plus 1/2” (1.3 cm) from the floor and 3-5/8” (9.2 cm)
from where the right side of range (facing range) is to be located.
17
Mark and drill holes where bracket
will be located.
Anti-tip Device Installation (cont.)
4
4
1
2
”
3/8cm)
95
(0.
Attach bracket with
mounting hardware provided.
Check that unit is level side to side
and front to back. The side trim must be 3/8” (0.95 cm)
above countertop. If unit is not level repeat steps 5-7
of “Leveling/Adjustments/Alignment” section.
Final Installation
1
Note: Refer to range electrical
requirements section for proper
installation information.
Connect electrical in shaded area. See the “Electrical
Requirements” section for more information.
2
3
Install backguard.
Slide range into place. Be sure anti-tip
bracket slides into the anit-tip opening.
18
19
Door Replacement and Adjustment
Final Preparation
2
1
2
• All stainless steel body parts should be
wiped with hot, soapy water and with a
liquid cleaner designed for this material.
If buildup occurs, DO NOT use steel wool,
abrasive cloths, cleansers, or powders!
If it is necessary to scrape stainless steel
1
2
to remove encrusted materials, soak with
hot, wet cloths to loosen the material, then
use a wool or nylon scraper. DO NOT use
a metal knife, spatula, or any other
material tool to scrape stainless steel!
Scratches are almost impossible to
remove.
3
Reattach door to range.
Open door completely. Reattach hinge trim.
3
Performance Checklist
A qualified installer should carry out the
following checks:
4
h Check self-clean function—door will lock
in approximately 30 seconds, the center
and outside broil elements will turn on and
the bake element will turn on at partial
power. Check broil elements through
window to make sure they are on, then
abort self-clean cycle to unlock door.
h Check top surface elements—glow red
when turned on.
h Check hot surface indicator lights—glow
red when corresponding element is on.
NOTICE
h Check oven bake function—bake element
on full power, center and outside broil
elements at partial power.
Remove pins from hole in hinges.
Close door.
When conducting performance test,
DO NOT run self-clean cycle for more
than 10 minutes with oven racks inside
oven. This could cause them to discolor
due to the high temperature required
for self-cleaning.
h Convection bake function—bake and broil
elements the same with the convection fan
on.
h Check TruConvec™ function—TruConvec
element (behind convection fan cover) on
and convection fan on.
5
h Check HI broil function–both broil
elements at full power.
h Check LOW broil function—inner broil
element only.
If the door needs to be adjusted, loosen hinge trim screws (see step 2).
Adjust the screws located between the door and kickplate using a 5/32”
hex head allen wrench. After adjustment, tighten hinge trim screws.
20
h Check convection broil function—both
broil elements at full power with convection
fan on.
21
Service & Registration
Only authorized replacement parts may be used in performing service on the appliance.
All servicing should be referred to a qualified technician.
Contact Viking Range Corporation, 1-888-VIKING1 (845-4641), for the nearest service parts
distributor in your area or write to:
VIKING RANGE CORPORATION
PREFERRED SERVICE
1803 Hwy 82W
Greenwood, Mississippi 38930 USA
Range – The serial number and model number for your appliance can be
found by opening the door and looking under the control panel.
Notes
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
Record the following information indicated below. You will need it if
service is ever required.
Model number ____________________________________________________________________________________
Serial number _____________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
Date of purchase __________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
Date installed ______________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
Dealer's name _____________________________________________________________________________________
Address ___________________________________________________________________________________________
These installation instructions should remain with the unit for future reference.
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
22
23