FILE #E21609
S1500TA & S1504TA
Electric Toe Space Heaters
with built-in thermostat
Installation & Maintenance Instructions
Dear Owner,
Congratulations! Thank you for purchasing this new heater manufactured by a division of Marley
Engineered Products. You have made a wise investment selecting the highest quality product in the heating industry. Please carefully read the installation and maintenance instructions shown in this manual.
You should enjoy years of efficient heating comfort with this product from Marley Engineered Products...
the industry’s leader in design, manufacturing, quality and service.
... The Employees of
Marley Engineered Products
WARNING
!
Read Carefully - These instructions are written to help
5.
you prevent difficulties that might arise during installation
of heaters. Studying the instructions first may save you
considerable time and money later. Observe the following
procedures, and cut your installation time to a minimum.
To reduce risk of fire or electric shock:
1.
2.
3.
4.
6.
Disconnect all power coming to heater at main service panel
before wiring or servicing.
All wiring must be in accordance with the National and Local
Electrical Codes and the heater must be grounded as a precaution against possible electric shock.
Verify the power supply voltage coming to heater matches the
ratings printed on the heater nameplate before energizing.
This heater is hot when in use. To avoid burns, do not let bare
skin touch hot surfaces.
7.
8.
9.
Do not insert or allow foreign objects to enter any ventilation
or exhaust opening as this may cause an electric shock, fire,
or damage to the heater.
To prevent a possible fire, do not block air intakes or exhaust
in any manner. Keep combustible materials, such as crates,
drapes, etc., away from heater. Do not install behind
doors, furniture, towels, or boxes.
A heater has hot and arcing or sparking parts inside. Do not
use it in areas where gasoline, paint or flammable liquids are
stored.
Use this heater only as described in this manual. Any other
use not recommended by the manufacturer may cause fire,
electric shock, or injury to persons.
This heater is not approved for use in corrosive atmospheres
such as marine, green house or chemical storage areas.
SAVE THESE INSTRUCTIONS
1
!
WARNING
TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT
INSTALL WITHOUT BACK BOX. DO NOT OPERATE WITHOUT
GRILLE INSTALLED.
CAUTION
!
1. DO NOT USE HEATER FOR DRY OUT. PAINT, PLASTER, SAWDUST, AND DRYWALL SANDING DUST MUST BE KEPT OUT OF
HEATER.
6.
7.
2. THE HEATER IS HOT WHEN IN USE. DO NOT INSTALL THE
HEATER BEHIND DOOR, BEHIND TOWEL RACK, IN CLOSET,
WHERE CURTAINS OR DRAPES COULD TOUCH OR BECOME
SCORCHED BY HEATER, OR WHERE AIRFLOW TO HEATER MAY
BE OBSTRUCTED. KEEP ELECTRICAL CORDS, BEDDING, FURNITURE AND OTHER COMBUSTIBLES AWAY FROM HEATER.
SPECIFICATIONS
NOTE: Heater is equipped with built-in thermostat. If a wall thermostat is used, a separate feed from wall thermostat to heater is
required. See wiring diagram Fig 3.
NOTE: Hole location should be 12” from corner and
1/4” above finished floor.
CAUTION
pole must cycle heating element only, not the motor.
Cycling both supply leads will defeat fan delay off feature and result in over-heating and possible damage to
heater.
b. Disconnect blue lead from built-in thermostat lead at
point A on wiring diagram, Fig. 3. Cap off thermostat
lead with wirenut. Connect blue lead to field supply lead
from load side of thermostat. (See Fig. 3) Make remaining field wiring connections per Fig. 3.
Replace and secure top cover on heater enclosure, and then
position heater into opening.
Using the holes in the flanges of the enclosure for a template,
secure both the front grille and the heater by drilling two
.093” (3/32”)(2.3 mm) diameter holes into the cabinet board
and installing two No. 6 x 3/4” (152.4 x 19 mm) screws
(supplied) through hole “A.” (See Fig. 1).
Model No
S1500TA
Wattage
Voltage
Amperage
120
12.5
6.3
1500
750
!
S1504TA 1500 / 1125 240 / 208
750 / 564
USE OF REMOTE THERMOSTAT WHICH SHUTS OFF POWER TO
HEATER DEFEATS FAN DELAY FEATURE AND DOES NOT ALLOW
HEATER TO COOL DOWN AS REQUIRED. WIRING HEATER IN THIS
MANNER WILL RESULT IN OVER-HEATING AND POSSIBLE DAMAGE TO HEATER AND/OR SURROUNDINGS. WIRE HEATER
EXACTLY AS SHOWN IN WIRING DIAGRAMS, FIG. 2 & FIG. 3.
TO CHANGE WATTAGE OUTPUT
The chart shows the wattages available by model. Each heater
is factory wired for its maximum wattage. To change wattage
remove the Red Jumper at left side of element (See Fig. 3 & 4).
HORIZONTAL INSTALLATION ONLY
This heater may be wired with standard building wiring (rated minimum 60° C).
L1
Fig. 2
1.
Cut a 14 1/4” x 3 5/8” (361.9 x 92.1 mm) opening at desired
location as shown in Fig. 1. Keep clearance area free of
obstructions.
2. Remove top cover from heater enclosure by removing the
cover screws.
3. Determine which knockout in enclosure will be used for field
wiring and remove (see Fig 1). Install strain relief (field
supplied).
4. Fish field wiring through strain relief leaving 6” (12.7 mm) of
wire inside box.
5. Make wiring connection, attaching field wiring to two (2) black
pigtail leads for 240/208V model, or to black and white pig tail
leads for 120V model with wirenuts (provided). Connect field
ground lead to ground pigtail with wirenut (provided). See
Fig. 2.
NOTE: If wall thermostat is used:
a. A double pole wall thermostat of the type where both
poles cycle on and off by temperature change cannot be
used with this heater. Only one pole may cycle and this
L2 or N
SOCKET PLUG
GND
Black
Fan
Motor
240V-Black
120V-White
Blue
Delay
Built-in Single Pole
Thermostat
(Or Remote Thermostat)
Blue
Blue
Thermal
Fuse
Auto
Reset
Limit
Light
Blue
Fig. 1
Red
Jumper
CLEARANCE AREA
FOR HEATER
CABINET
6.3 / 5.4
3.1 / 2.7
14-1/4
Rear Coil Element
Front Coil Element
3-5/8
Wiring Diagram - For Built-in Thermostat
For 750 watt, remove red jumper
Knock-outs
Knockouts
Hole "A"
Hole
“A”
2
IMPORTANT INFORMATION
Fig. 3
Temperature
cycled pole
SEE NOTE BELOW
THIS DIAGRAM
L1
CAUTION
Manual On-Off pole
FOR CORRECT AND CONTINUED SAFE OPERATION, YOUR HEATER
MUST BE INSPECTED AND CLEANED PERIODICALLY. DEPENDING ON
THE APPLICATION, THE HEATER SHOULD BE INSPECTED AND CLEANED
AT LEAST ANNUALLY. IF USED AS PRIMARY HEAT, INSPECT AND CLEAN
HEATER AT LEAST TWICE A YEAR OR MORE OFTEN IF NECESSARY. DO
NOT CONTINUE TO USE THIS HEATER IF LINT AND DIRT HAVE ACCUMULATED INSIDE HEATER.
L2 or N
Remote double-pole wall thermostat
This lead supplies the
motor and must not be
cycled by the thermostat
SOCKET PLUG
Black
GND
Motor
Blue
Fan
240V-Black
120V-White
Delay
Blue
Single-pole built-in
thermostat (low or
off position)
TO
1.
2.
3.
4.
5.
CLEAN HEATER:
Disconnect power at main service panel.
Remove screws and grille.
Slide heater and back box out.
Remove top of enclosure.
Clean blower and inside of heater using vacuum cleaner w/
brush attachment.
6. Carefully spin blower wheel wih finger to make sure it turns
freely. Look for any damage or overheating of wiring connectors or components. If any problem is discovered, discontinue use of heater until it is repaired.
7. Replace cover.
8. Slide heater back in place.
9. Secure grille and heater with screws.
10. Reconnect power.
11. Verify heater operates properly
OPERATIONAL NOTICE
Your heater is equipped with an automatic reset limit control that
will automatically turn the heater OFF to prevent a fire if the
heater overheats. Should this occur, the indicator light will illuminate and will continue to shine until the limit resets.
A
Thermal
Fuse
Auto
Reset
Limit
CAUTION
!
THE ILLUMINATED INDICATOR LIGHT SIGNIFIES THE HEATER HAS BEEN
SUBJECTED TO SOME ABNORMAL CONDITION CAUSING IT TO OVERHEAT. CHECK HEATER TO INSURE THAT IT HAS NOT BEEN BLOCKED IN
ANY MANNER (IF SO, REMOVE BLOCKAGE). IF THERE IS NO INDICATION
OF BLOCKAGE IT IS RECOMMENDED THE HEATER BE CHECKED BY A
REPUTABLE ELECTRICIAN OR REPAIR SERVICE TO INSURE THE
HEATER HAS NOT BEEN DAMAGED.
Light
Red
Jumper
Rear Element
Front Element
!
Wiring Diagram - For Remote Thermostat
For 750 watt, remove red jumper
NOTE: If wall thermostat is used: a double pole wall thermostat of the type where both poles cycle on and off by
temperature change cannot be used with this heater. Only
one pole may cycle and this pole must cycle heating element only, not the motor. Cycling both supply leads will
defeat fan delay off feature and result in over-heating and
possible damage to heater.
NAMEPLATE
MODEL NO.
S1504TA
FAN FORCED WALL HEATER
240
1500/750
VOLTS AC
WATTS
DATE CODE
0197
6.2/3.1
AMPS
CAUTION: USE ONLY WITH TS ENCLOSURE.
DO NOT OPERATE WITHOUT GRILLE IN PLACE.
!
ATTENTION: UTILISER UNIQUEMENT AVEC UN BOÎTIER TS.
NE PAS FAIRE FONCTIONNER SANS LA GRILLE.
WARNING
PRECAUTION: USARLO SÓLO CON LA CUBIERT A TS.
NO DEVE ENCENDERSE SIN LA REJILLA.
YOUR HEATER IS PROVIDED WITH A BACK-UP THERMAL SAFETY
FUSE THAT WILL OPEN ONLY IF THE HEATER IS IN NEED OF
MAJOR REPAIRS. DO NOT BYPASS THIS FUSE. THE HEATER CAN
ONLY BE REPAIRED BY A QUALIFIED SERVICE CENTER.
Marley Engineered Products
BENNETTSVILLE, SC 29512
3
774G LISTED
ROOM HEATER
4104-2165-002
LIMITED WARRANTY
All products manufactured by Marley Engineered Products are warranted against defects in workmanship and materials for one year from date of installation, except heating elements which are warranted against defects in workmanship and materials for five years from date of installation. This warranty
does not apply to damage from accident, misuse, or alteration; nor where the connected voltage is more than 5% above the nameplate voltage; nor to
equipment improperly installed or wired or maintained in violation of the product’s installation instructions. All claims for warranty work must be accompanied by proof of the date of installation.
The customer shall be responsible for all costs incurred in the removal or reinstallation of products, including labor costs, and shipping costs incurred
to return products to Marley Engineered Products Service Center. Within the limitations of this warranty, inoperative units should be returned to the
nearest Marley authorized service center or the Marley Engineered Products Service Center, and we will repair or replace, at our option, at no charge
to you with return freight paid by Marley. It is agreed that such repair or replacement is the exclusive remedy available from Marley Engineered Products.
THE ABOVE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE AFORESAID EXPRESSED WARRANTIES ARE HEREBY
DISCLAIMED AND EXCLUDED FROM THIS AGREEMENT. MARLEY ENGINEERED PRODUCTS SHALL NOT BE LIABLE FOR CONSEQUENTIAL
DAMAGES ARISING WITH RESPECT TO THE PRODUCT, WHETHER BASED UPON NEGLIGENCE, TORT, STRICT LIABILITY, OR CONTRACT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For the address of your nearest authorized service center, contact Marley Engineered Products in Bennettsville, SC, at 1-800-642-4328. Merchandise
returned to the factory must be accompanied by a return authorization and service identification tag, both available from Marley Engineered Products.
When requesting return authorization, include all catalog numbers shown on the products.
HOW TO ORDER REPAIR PARTS
In order to obtain any needed repair or replacement
parts, warranty service or technical information, please
contact Marley Engineered Products Service Center tollfree by calling 1-800-642-HEAT.
When ordering repair parts, always give the information listed as follows:
1. The Part Number
2. The Model Number
3. The Part Description
4. Date of Manufacture
470 Beauty Spot Rd. East
Bennettsville, SC 29512 USA
ECR 35211
Part No. 5200-2329-003
6/02
4