Regulatory Information
FCC Information
A-T-27-V
FCC compliance: This equipment has been tested
and found to comply with the limits for a digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful interference
to radio communications. Operation of this
equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at his own
expense.
FCC Conditions
UD.6L0201D1829A02
Thank you for purchasing our product. If there
are any questions, or requests, please do not
hesitate to contact the dealer.
This manual may contain several technical
incorrect places or printing errors, and the content
is subject to change without notice. The updates
will be added to the new version of this manual.
We will readily improve or update the products or
procedures described in the manual.
Privacy Notice
Surveillance laws vary by jurisdiction. Check all
relevant laws in your jurisdiction before using
this product for surveillance purposes to ensure
that your use of this product conforms.
Please refer to the product specification for
camera parameters and functions.
0100001050305
For proper recycling, return the battery to your
supplier or to a designated collection point. For
more information see: www.recyclethis.info.
1 Introduction
1.1 Product Features
This camera adopts new generation sensor with high
sensitivity and advanced circuit board design
technology. It possesses the features of high
resolution, low distortion, and low noise, etc. It is
extremely suitable for supervisory system and image
processing system.
The main features are as follows:
High performance CMOS sensor and high
resolution bring high-quality image;
Low illumination;
Support IR cut filter with auto switch; OSD
menu, parameters are configurable;
Support auto white balance, auto gain control,
electronic shutter control and internal
synchronization;
SMART IR mode;
Unit transmission control;
Advanced 3-axis design meets different
installation requirements.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
1.2 Overview
EU Conformity Statement
1.2.1 Overview of Type I Camera
This product and - if applicable - the
supplied accessories too are marked
with "CE" and comply therefore with
the applicable harmonized European
standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC, the
RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in the European Union.
For proper recycling, return this product
to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points.
www.recyclethis.info.
For more information see:
2006/66/EC (battery
directive): This product contains a
battery that cannot be disposed of as
unsorted municipal waste in the
European Union.
See the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg).
Before you start:
Please make sure that the device in the package is
in good condition and all the assembly parts are
included.
Make sure that all the related equipment is
power-off during the installation.
Check the specification of the products for the
installation environment.
Check whether the power supply is matched
with your power output to avoid damage.
Please make sure the wall is strong enough to
withstand three times the weight of the camera
and the mounting.
If the wall is the cement wall, you need to insert
expansion screws before you install the camera. If
the wall is the wooden wall, you can use selftapping screw to secure the camera.
If the product does not function properly, please
contact your dealer or the nearest service center.
Do not disassemble the camera for repair or
maintenance by yourself.
2.1 Ceiling Mounting
Steps:
AC24V Power Cable
Black Liner
2 Installation
1.Drill the screw holes and the cable hole on the
ceiling according to the supplied drill template.
Type I:
Type II:
HD Video Cable
Lens
Menu Joystick
DIP Switch
Auxiliary Video Output
Base Plate
Figure 2-1 The Drill Template
Bubble
Figure 1-1 Overview of Type I Camera
1.2.2 Overview of Type IICamera
AC24V Power Cable
Black Liner
Lens
2.Loosen the screws on the bubble of type 1
camera /rotate the bubble of type2 camera to
remove the bubble and the black liner.
Type I:
Type II:
HD Video Cable
Menu Joystick
DIP Switch
Base Plate
Auxiliary Video Output
Bubble
Figure 1-2 Overview of Type II Camera
Figure 2-2 Remove the Bubble
3.Attach the back box of type 1 camera /base plate of
type2 camera to the ceiling and secure them with
supplied self-tapping screws.
4.Route the cables through the cable hole. 5.Align
the camera with the back box/base plate, and
tighten the set screws to secure the camera with
the back box/base plate.
Type I:
Type II:
5.Fix the camera to the in-ceiling mount with the
supplied screws.
Type I:
Type II:
Menu
AWB
VIDEO. OUT DAY&NIGHT
FRAME
RATE
0°~75°
T Direction
0°~355°
P Direction
0
SYSTEM
AUTO
DC
PRIVACY
ZONE
COLOR
GAIN
CAMERA
ID
ESC
MOTION
COLOR
HUE
ID DISP
HOLD
HLC
SHARPNESS
NAME
DISP
CONTRAST
LANGUAGE
BRIGHT
FACTORY
INIT
B/W
EXIT
R Direction
°~
355
0° ~340°
P Direction
8000K
EXT
4200K
2.3 In-ceiling Mounting with
Gang Box
Only the type 1 camera supports in-ceiling
mounting with gang box.
1.Repeat steps 2-4 of the In-ceiling Mounting
section to secure the in-ceiling mount (supplied) to
the gang box.
Figure 2-7 Install the Mount 2.Route
and connect the corresponding cables.
3.Align the camera with the gang box, and tighten the
screws to secure the camera with the gang box..
Figure 2-4 3-axis Adjustment
3200K
MIRROR
PUSH
FLIP
Figure 3-1 Main Menu
A coaxial camera controller (purchase separately) is
required to select the menu and adjust the camera
parameters.
3.1 VIDEO.OUT
You can set the frame rate as 25 fps/30fps.
3.2 DAY/NIGHT
Color, B/W, AUTO and EXT are selectable for DAY/
NIGHT switches. Under the mode of the AUTO and
EXT, you can set the IR LED as Smart and CDS. If the IR
LED is selected as Smart, you can set the bright-ness of
the IR LED.
1.Drill the screw holes and the cable hole in the
ceiling according to the supplied drill template.
2.Screw the bolts through the mount by aligning with
the 2 bolt holes. Fit the toggles onto the bolts. 3.Push
the two toggle bolts through the two screw holes on
the ceiling. Rotate the bolt till the toggle holds the
ceiling tightly.
Figure 2-5 Install the Mount 4.Route
and connect the corresponding cables.
1. MODE
2. D TO N
3. N TO D
4. DELAY TIME
5. RETURN
AUTO
63
63
20
RET
Figure 3-2 DAY/NIGHT
2.2 In-ceiling Mounting
Steps:
AUTO
255
151
RET
Figure 3-3 AWB
6000K
°
You need to purchase an in-ceiling mount separately if
you adopt in-celling mounting.
1. MODE
2. R-G GAIN
3. B-G GAIN
4. RETURN
HOLD
DAY/NIGHT
0° ~75°
T Direction
0°~355°
EFFECT
AUTO
Type I I:
R Direction
SPECIAL
USER
6. Repeat steps 6-8 of the Ceiling Mounting section to
complete the installation.
Type I:
AE
COLOR
Figure 2-6 Fix the Camera to the Mount
Figure 2-3 Fix the Camera to the Ceiling
6. Connect the corresponding cables.
7. Adjust the camera according to the figure below to
get an optimum angle.
8. Fit the black liner on the camera and tighten the
screws on the bubble of type 1 camera or rotate the
bubble of type 2 camera to complete.
AWB
Figure 2-8 Fix the Camera to the Gang Box
4. Repeat steps 6-8 of the Ceiling Mounting section to
complete the installation.
3 Menu Operation
Press the menu button to enter the menu interface.
When the menu interface is not displayed, you can
press and hold any direction key of the joystick
for 3s to enter the focusing interface. Move the
joystick to adjust the camera lens by the FOCUS+,
FOCUS-, ZOOM+ and ZOOM-.
After connecting the camera with back-end device, you
can also control the camera with mouse in PTZ control
mode. The direction keys works as the menu joystick.
SPECIAL
1. PRIVACY
ZONE
2. MOTION
3. HLC
4. RETURN
RET
Figure 3-4 SPECIAL
3.3.3 AWB
Auto, User, Push, 8000k, 6000k, 4200k and 3000k are
selectable for AWB. Under the mode of AUTO, you
need to set the R-G/B-G Gain and to select an
indoor/outdoor mode. If the AWB mode is select as
User, You need to set the R/G/B Gain manually.
3.3.4 AE
You can set the AE mode as HOLD, DC and ESC.
Brightness: Brightness refers to the brightness of
the image.
Shutter: Shutter denotes the speed of the shutter.
You can set the shutter as AUTO, 1/25, 1/30, 1/50,
1/60, 1/100, 1/120, 1/250, 1/500, 1/1k, 1/3k and
1/10k.
Flicker: You can set the flicker status as 50HZ/60HZ to
prevent image flicking.
BLC: BLC bases on the back area to enhance the
brightness of the whole image. You can set the BLC
gain from 0 to 16.
AGC: AGC optimizes the clarity of image in poor light
scene. The value of AGC can be set from 1-5. LSC:
LSC corrects the phenomenon where the image gets
darkened or blurred on the periphery.
3.3.5 SPECIAL
Privacy zone: Select a PRIVACY area. Set the MASK
PAT as OFF, GRAY, WHITE or BLACK. Set the
SX/EX/SY/EY value to define the position and size of
the area.
Motion: Set the Motion status as ON or OFF. Set the
SENSITIVITY from 0 to 255. Set the alarm status as
ICON/TRANCE/OFF. Set the hold time from
0 second to 255 seconds.
HLC: HLC supplements the brightness of the
peripheral area of the image. You can set the mask
value and threshold from 0 to 255.
3.3.6 EFFECT
Color Gain: Color gain adjust this feature to change
the saturation of the color. You can set the value from
0 to 255.
Color Hue: You can adjust the image HUE from 0
to 71.
Sharpness: Sharpness determines the amount of
detail that an imaging system can reproduce. You
can set the value from 0 to 255.
Contrast: Contrast enhances the difference in
color and light between parts of an image. You
can set the value from 0 to 255.
Bright Off.: Bright Off. refers to the brightness
compensation of the image. You can set the bright
compensation value as 0 or 1.
Mirror: You can set the Mirror status as ON/OFF.
Flip: You can set the FLIP status as ON/OFF.
EFFECT
1. COLOR GAIN 200
2. COLOR HUE 200
3. SHARPNESS
25
4. CONTRAST
150
5. BRIGHT OFF.
1
6. MIRROR
ON
7. FLIP
ON
8. RETURN
SYSTEM
1. CAMERA ID
255
2. ID DISP.
ON
3. NAME DISP.
ON
4. LANGUAGE
ENG
5. FACTORY INIT
OFF
6. RETURN
RET
RET
Figure 3-5 EFFECT
Figure 3-6 SYSTEM
3.3.7 SYSTEM
You can set the camera ID from 0 to 255. Select
the ID display and name display status as ON/OFF.
Chinese and English are selectable for the language of
the menu.
You can restore the camera to the default by
setting the factory initialization status as ON.
3.3.8 EXIT
Exit and Save & exit are selectable.
Download PDF
Similar pages
User Manual
null 10331538
2 Installation
User Manual
null 11616515
THC-1002IR - Balter Security
Untitled - Luxon Video