Start Up Procedures Turning the Espresso Machine On

Start Up Procedures
Turning the Espresso
Machine On
• The following is the procedure for turning
on the power to the espresso machine.
• Please follow the procedures carefully
to avoid any damage to the espresso
machine.
NOTE: If the message “First Installat. Enter
to confirm” appears in the display, please
see the preceding page entitled “Initial
installation”.
Operating Procedure
1
The following is the procedure for turning on the power to the espresso machine. Turn the Main Switch to
the On position.
LaMarzocco
Rev. 1.09
2
The message at left will be displayed briefly. This message indicates the revision level of the software installed in this
espresso machine.
OFF
3
To complete the turn on process, press the
button and the display at left is shown. The machine begins to automatically
fill the steam boiler until full. The display is asking if you have completed the coffee boiler air bleeding process (of the coffee
boiler). When this process is complete, press the enter button. If the screen does not change, wait until the steam boiler is
completely full and try again.
4
5
The espresso machine is now ON and you should see one of the two following displays.
LaMarzocco 09:30
09:30
LaMarzocco 09:30
Boiler:
09:30
When the espresso machine reaches operating temperature the lights on all keypads will light indicating that the espresso
machine is ready to use.
HAZARDOUS VOLTAGE DISCONNECT FROM POWER SUPPLY BEFORE SERVICING
EN
Display
Description
22
Shut Down Procedures
Description
Turning
the Espresso
Programming
Mode
Machine Off
• The following is the procedure for turning
off power to the espresso machine.
• Please follow the procedures carefully
to avoid any damage to the espresso
machine.
LaMarzocco 09:30
Display
has two off settings:
turns off all of the
the espresso machine.
turns off power to
espresso
machine.
Operating Procedure
LaMarzocco 09:30
1
The following is the procedure for safely turning off the espresso machine.
LaMarzocco 09:30
2
Press and hold the
LaMarzocco 09:30
3
This is the OFF setting used in the normal operating conditions.
4
During servicing or other conditions that warrant it the main switch should be turned to the OFF or “0” position.
5
The espresso machine is off and display should be blank. It is important to follow this procedure when turning off the
machine. Failure to do so can damage the electronics.
OFF
EN
• This machine
- One setting
components in
- The other
the
complete
23
09:30
button (approximately 3 seconds). The display changes to the following:
HAZARDOUS VOLTAGE DISCONNECT FROM POWER SUPPLY BEFORE SERVICING
“Barista” Programming
Water Volume Programming
Water Volume
Programming
Description
• This parameter allows the operator
to program the water volume (shot
volume) for the individual buttons on
the keypad.
Display
• The saved program is a number. This
number relates to the number of pulses
the flowmeter delivers to the CPU. Once
the programmed number of pulses is
received by the CPU, the flow of water
is stopped.
Operating Procedure
LaMarzocco 09:30
1
Press and hold the
Water Volume
Programming
2
button on the group 1 keypad again. The lights on the first 4 buttons will light and the light on the continuous
Press the
button will begin flashing. The flashing light indicates the keypad is in programming mode
3
While in programming mode, press any of the first 4 buttons. When the desired amount of water has been dispensed, press
the same button again to stop the flow of water. Continue this same procedure for all buttons that programming is desired.
4
5
Once the first 4 buttons are programmed, press the
button on the group 1 keypad until the following is displayed (approximately 5 seconds):
button to exit programming mode
To program the tea water dispense button, repeat procedure 1 then press the
been dispensed, press the
programming mode.
the button. When the desired amount of water has
button again to stop the flow of water. When finished
press the button to exit
NOTE: The programming completed for group 1 keypad will be copied to all subsequent keypads. If other programming is desired
for subsequent keypads, follow procedure 1 and 2 substituting the subsequent group keypad number for procedure 2.
It is recommended to program each group separately.
EN
that you wish to program. When the light begins to flash, press
button on the corresponding keypad
24
“Barista” Programming
Nominal
CoffeeMode
Boiler
Programming
Temperature
Cofee Boilers
Temperatures
EN
Display
Description
• This parameter is set at the factory at a
preset nominal temperature.
• The set temperature of this parameter
differs from the actual temperature of
the water exiting the group to the coffee.
• The temperature of the boiler is
measured at the most critical point in the
boiler when temperature fluctuation is
the greatest.
• The temperature of the water exiting the
group head is held constant by means
of the mass of the group casting. Even
though the temperature of the boiler
may vary a few degrees, the temperature
of the water exiting the group is constant.
• To set the temperature of any espresso
machine it is important to measure the
temperature of the water exiting the
group.
Operating Procedure
LaMarzocco 09:30
1
Press and hold the
Water Volume
Programming
2
Press the
button on the group 1 keypad until the following appears (one time):
Coffee Boilers
Temperatures
3
Press the
button to select the coffee boiler you wish to change temperature.
Coffee Boiler 1
202.5 F 2 0 2.6 F
4
Press the
or the
button to change the temperature on the displayed boiler. The measured temperature appears
on the left and the set temperature appears on the right side of the display. Once the desired temperature is selected press
the button
to confirm the selection.
5
Repeat procedure 5 for all subsequent boilers (if installed).
6
When finished, continue to the next parameter
25
button on the group 1 keypad until the following is displayed (approximately 5 seconds):
or press
to exit programming mode.
“Barista” Programming
Description
Cup Heating
• This parameter allows the user to enable
or disable the cup heating routine.
• The cup heater is an option ordered
from the factory, not available in the
USA & Canada.
• Additional parameter settings are
available in the factory level parameters
under Cup Heating Times.
Cup heating
DISABLED
Display
Operating Procedure
LaMarzocco 09:30
1
Press and hold the
Water Volume
Programming
2
Press the
Cup heating
DISABLED
3
Press the
or the
button to change to ENABLED or DISABLED. Once the desired condition is displayed press
the
button to confirm.
4
When finished, continue to the next parameter
button on the group 1 keypad until the following is displayed (approximately 5 seconds):
button on the group 1 keypad until the following appears (two times):
to exit programming mode.
EN
or press
26
“Barista” Programming
Description
Programming
Doses Reading
Mode
• This parameter allows the user to review
the total doses dispensed for each
button.
• The number displayed is the total
number of times the individual button
has been activated.
Doses Reading
press + or -
EN
Display
Operating Procedure
LaMarzocco 09:30
1
Press and hold the
Water Volume
Programming
2
Press the
button on the group 1 keypad until the following appears (three times):
Doses Reading
press + or -
3
Press the
or the
4
When finished, continue to the next parameter
27
button on the group 1 keypad until the following is displayed (approximately 5 seconds):
button to scroll through the values for each button.
or press
to exit programming mode.
“Barista” Programming
Description
Clock Adjust
• This parameter allows the user to set the
time of day and the day of the week.
• This parameter is used by the “Auto On/
Off” parameter
Clock adjust
09:30 Tuesday
Display
Operating Procedure
LaMarzocco 09:30
1
Press and hold the
Water Volume
Programming
2
Press the
Clock adjust
09:30 Tuesday
3
The hour value should be flashing. Press the
4
button to change to minute value and again to change to the day of the week
Press the
value. Follow step 3 to change these values.
5
When finished, continue to the next parameter
button on the group 1 keypad until the following is displayed (approximately 5 seconds):
button on the group 1 keypad until the following appears (four times)
or press
button to change the hour.
to exit programming mode.
EN
or the
28
“Barista” Programming
Description
Programming
Auto On/Off
Mode
• This parameter allows the user to
program the espresso machine to turn
on at a preset time and turn off at a
preset time.
• This feature also allows the espresso
machine to remain in the off condition
for one repeating closed day.
Auto On/Off
On:
--.--
Display
LaMarzocco 09:30
1
Press and hold the
Water Volume
Programming
2
Press the
Auto On/Off
On:
--.--
3
The hour value should be flashing. Press the
4
Press the
button to change to the minute value. Follow step 3 to change this value.
5
Press the
button again to change to hour value for the “Off” time. Follow step 3 to change this value.
6
Press the
button again to change to minute value for the “Off” time. Follow step 3 to change this value.
7
Press the
button again to change to the “Closed On” value. Follow step 3 to change this value
8
When finished, continue to the next parameter
Auto On/Off
Off:
--.--
Closed On
-----------
EN
Operating Procedure
29
button on the group 1 keypad until the following is displayed (approximately 5 seconds):
button on the group 1 keypad until the following appears (five times):
or the
or press
button to change the hour for the “On” time.
to exit programming mode.
“Technical” Programming
Language
Description
• This parameter allows the technician to
change the language of the display.
Language
ENGLISH
Operating Procedure
1
Press and hold the
Password
?????
2
Enter the 5 digit technician password using buttons 1-5 on the group 1 keypad. Once accepted the following appears:
Language
ENGLISH
3
or the
button to change the display language. You may choose from Italian, Francaise, English or
Press the
Deutsch. Once the desired selection is made press the
button to confirm the selection.
4
When finished, continue to the next parameter
LaMarzocco 09:30
button on the group 1 keypad until the following is displayed (approximately 10 seconds):
or press
to exit programming mode.
EN
Display
30
“Technical” Programming
Temperature
Programming
Correction
Mode
Temp.correction
Temperatures
Description
• This parameter allows the technician to
adjust the temperature of the individual
coffee boilers.
• This procedure is best completed with
an external temperature measuring
device that measures the water exiting
the group at the point of contact with
the coffee.
Display
LaMarzocco 09:30
1
Press and hold the
Password
?????
2
Enter the 5 digit technician password using buttons 1-5 on the group 1 keypad. Once accepted the following appears:
Language
ENGLISH
3
Press and hold the
Temp.correction
Temperatures
4
Press the
5
or the
button to adjust the temperature higher or lower. Each block is equal to 32.9°F (0.5°C). Once
Press the
the desired setting is made press the button
to confirm and advance to the next boiler (if available).
6
7
Repeat procedure 5 for all subsequent boilers.
Coffee Boiler 1
EN
Operating Procedure
31
button on the group 1 keypad until the following is displayed (approximately 10 seconds):
button on the group 1 keypad until the following appears (one time):
button on the group 1 keypad one time and the following appears:
When finished, continue to the next parameter
or press
to exit programming mode.
“Technical” Programming
Autosteam Temperature
Adjustment
Temp.correction
Autosteam
• When the parameter Autosteam is set
to ENABLED, this parameter is enabled.
• To accurately measure milk temperature,
an external temperature measuring
device should be used. Changes to the
values contained in this parameter
should be done based upon the external
temperature measuring device.
• There is the possibility to install two
Autosteam steaming wands; Autosteam
1 and Autosteam 2. Each Autosteam
works independantly and must be set
separately.
• If it is not possible to achieve the desired
temperature setting please contact
your local La Marzocco dealer for help
troubleshooting this issue.
Operating Procedure
LaMarzocco 09:30
1
Press and hold the
Password
?????
2
Enter the 5 digit technician password using buttons 1-5 on the group 1 keypad. Once accepted the following appears:
Language
ENGLISH
3
Press the
button on the group 1 keypad until the following appears (about two times):
Temp.correction
Temperatures
4
Press the
button on the group 1 keypad one time and the following appears:
5
Press the
the desired
or the
button to adjust the temperature higher or lower. Each block is equal to 32.9°F (0.5°C). Once
setting is made press the button to confirm.
6
Repeat procedure 5 to adjust the temperature of Autosteam 2 (if installed).
7
When finished, continue to the next parameter
Autosteam 1
Autosteam 2
button on the group 1 keypad until the following is displayed (approximately 10 seconds):
or press
to exit programming mode.
EN
Display
Description
32
“Technical” Programming
Description
Programming
Total Doses
Mode
• This parameter keeps a count of each
dose that is produced with this espresso
machine.
• This number can be an important
reference when troubleshooting the
espresso machine.
• This number cannot be adjusted nor
reset.
Total doses
15
EN
Display
Operating Procedure
LaMarzocco 09:30
1
Press and hold the
Password
?????
2
Enter the 5 digit technician password using buttons 1-5 on the group 1 keypad. Once accepted the following appears:
Language
ENGLISH
3
Press the
Total Doses
15
4
The number displayed is the total number of doses that this machine has produced
5
When finished, continue to the next parameter
33
button on the group 1 keypad until the following is displayed (approximately 10 seconds)
button on the group 1 keypad until the following appears (about three times):
or press
to exit programming mode.
“Technical” Programming
Cronos Function (shot timer)
Crono Function
DISABLE
Display
Description
• When enabled, this parameter displays a
timer that times each shot.
• The corresponding timer is reset each
time a button on the corresponding
keypad is pressed
• When enabled, the Cronos Function is
continuously displayed. User name will
not be displayed when this parameter is
enabled.
Operating Procedure
LaMarzocco 09:30
1
Press and hold the
Password
?????
2
Enter the 5 digit technician password using buttons 1-5 on the group 1 keypad. Once accepted the following appears:
Language
ENGLISH
3
Press the
Crono Function
DISABLE
4
or the
button to change to ENABLED or DISABLED. Once the desired condition is displayed press
Press the
the
button to confirm
5
When finished, continue to the next parameter
button on the group 1 keypad until the following is displayed (approximately 10 seconds)
button on the group 1 keypad until the following appears (about four times):
or press
to exit programming mode.
NOTE: When this parameter is ENABLED the display will be changed to the following (3 group version shown here):
Gr2
0
Gr3
0
EN
Gr1
0
34
“Technical” Programming
Description
Programming
User Name
Mode
• This parameter allows the technician to
program a 16 character user name.
• The user name is displayed continuously
on the display on the second line.
• The user name is not displayed when the
Cronos Function is ENABLED.
User Name
.
Display
Operating Procedure
LaMarzocco 09:30
1
Press and hold the
Password
?????
2
Enter the 5 digit technician password using buttons 1-5 on the group 1 keypad. Once accepted the following appears:
Language
ENGLISH
3
Press the
4
or the
The first character in the user name is flashing. Press the
condition is displayed press the
button to advance to the next.
5
When finished, continue to the next parameter
User Name
.
button on the group 1 keypad until the following is displayed (approximately 10 seconds)
button on the group 1 keypad until the following appears (about five times):
or press
button to change the value. Once the desired
to exit programming mode.
EN
The following is a listing of the available characters:
35
ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789():., ,*+,-./!,,#&=?@ (BLACK SPACE)
“Technical” Programming
Pre-Brewing (Pre-Infusion)
Pre-Brewing
DISABLED
Display
Description
• This parameter allows the technician to
enable or disable the pre-brewing (also
called pre-infusion) function.
• Pre-brewing has two values to adjust.
T(tot) is the total time for pre-brewing.
T(on) is the amount of time that the
brew valve is open during T(tot). The off
time is calculated by subtracting T(on)
from T(tot).
Operating Procedure
1
Press and hold the
2
Enter the 5 digit technician password using buttons 1-5 on the group 1 keypad. Once accepted the following appears:
Language
ENGLISH
3
Press the
Pre-Brewing
DISABLED
4
Press the
or the
button to change to ENABLED or DISABLED. Once the desired condition is displayed press
the
button to confirm.
Key 1 Group 1
Ttot:20 Ton:10
5
If ENABLED is chosen, the display then shows the values for T(tot) and T(on) for each button.
Press
or the
to adjust a value and press
to advance to the next value.
6
Repeat procedure 5 for each button (key) that you wish to activate pre-brewing. A setting of T(tot) = 0 and T(on) = 0 disables
pre-brewing on the individual button.
7
When finished, continue to the next parameter
Password
?????
button on the group 1 keypad until the following is displayed (approximately 10 seconds)
button on the group 1 keypad until the following appears (about six times):
or press
to exit programming mode.
NOTE: The unit of measure for these values is 1/10 sec. Therefore a value of 10 equals 1 second.
EN
LaMarzocco 09:30
36
“Technical” Programming
Description
Programming
Filter Alarm
Mode
• This parameter allows the technician
to preprogram an alarm that notifies
the user when the water filter requires
service or replacement.
• When the programmed volume of
water has passed through the espresso
machine the error message “Change
Filter” is displayed.
Filter Alarm
Display
Operating Procedure
Press and hold the
Password
?????
1
2
Language
ENGLISH
3
Press the
button on the group 1 keypad until the following appears (about seven times):
Press the
button on the group 1 keypad until the following appears (about six times):
Change H2O Filt.
0 liters
4
5
Water Flow
12 cc/sec
6
Press the
or the
button to change the estimated flow rate of water. Normally this value should not be changed.
When the desired value is displayed press
to confirm.
7
When finished, continue to the next parameter
LaMarzocco 09:30
Filter
Alarm
EN
• A value of 0 (zero) disables the filter
alarm parameter.
37
button on the group 1 keypad until the following is displayed (approximately 10 seconds)
Enter the 5 digit technician password using buttons 1-5 on the group 1 keypad. Once accepted the following appears:
Press the
or the
button to change the volume of water required before filter servicing/replacing
is recommended. When finished press
to confirm.
or press
to exit programming mode.
Note: To reset the function turn off the machine with the
button (press and hold approximately 3 seconds). Next, press
and hold the
button while turning on using the
button.
“Technical” Programming
Steam Boiler Automatic Fill
Filling-up
with pump
Display
Description
• This parameter allows the technician to
select the activation of the water pump
during the steam boiler auto- fill cycle.
• Only under unusual circumstances
would the option of “without pump” be
chosen.
Operating Procedure
1
2
Press and hold the
Language
ENGLISH
3
Press the
Filling-up
with pump
4
Press the
or the
displayed press the
5
When finished, continue to the next parameter
Password
?????
button on the group 1 keypad until the following is displayed (approximately 10 seconds)
Enter the 5 digit technician password using buttons 1-5 on the group 1 keypad. Once accepted the following appears:
button on the group 1 keypad until the following appears (about eight times):
button to change to with pump or without pump. Once the desired condition is
to confirm.
or press
to exit programming mode.
EN
LaMarzocco 09:30
• The electronics installed in this espresso
machine give priority to the brew boiler
for pressure. The activation of the autofill cycle during the brewing process can
reduce the overall dispensing pressure
in the brew boiler.
• During the auto-fill cycle, if a brew cycle
is chosen, the auto-fill cycle is delayed
until all brew cycles are complete.
38
“Technical” Programming
Steam
Boiler Automatic
Programming
Mode Fill
During Coffee Dispensing
During Coffee Disp
Enable FillingUp
EN
Display
Description
• This parameter allows the technician
to Enable/Disable the steam boiler
automatic filling while dispensing coffee.
Operating Procedure
LaMarzocco 09:30
1
Press and hold the
Password
?????
2
Enter the 5 digit technician password using buttons 1-5 on the group 1 keypad. Once accepted the following appears:
Language
ENGLISH
3
Press the
During Coffee Disp
Enable FillingUp
4
or the
button to change to ENABLE or DISABLE. Once the desired condition is displayed press
Press the
ther
button to confirm.
5
When finished, continue to the next parameter
39
button on the group 1 keypad until the following is displayed (approximately 10 seconds)
button on the group 1 keypad until the following appears (about nine times):
or press
to exit programming mode.
“Technical” Programming
Description
Tea Water
• This parameter allows the technician to
select the activation of the water pump
during hot water dispensing.
• When hot water is drawn from only the
steam boiler this parameter should be
set to “without pump”.
• If the optional adjustable temperature
hot water dispense valve is installed, this
parameter is set to “with pump”.
Tea water
without pump
Display
Operating Procedure
LaMarzocco 09:30
1
Press and hold the
Password
?????
2
Enter the 5 digit technician password using buttons 1-5 on the group 1 keypad. Once accepted the following appears:
Language
ENGLISH
3
Press the
Tea water
without pump
4
or the
Press the
displayed press ther
5
When finished, continue to the next parameter
button on the group 1 keypad until the following is displayed (approximately 10 seconds)
button on the group 1 keypad until the following appears (about ten times):
button to change to with pump or without pump. Once the desired condition is
button to confirm.
to exit programming mode.
EN
or press
40
“Technical” Programming
Steam
Boiler Pressure
Programming
Mode
Regulation
Steam heat.Type
Temp. Probe
Display
Description
• This espresso machine comes with the
option of either a pressure switch or
a temperature probe for maintaining
pressure in the steam boiler.
• The temperature probe is standard on
all espresso machines. In some cases a
pressure switch may be used.
• The pressure switch regulates pressure
via a diaphragm type pressure switch.
The pressure may be adjusted via a small
screw on the switch.
• When a temperature probe has been
installed the pressure in the steam
boiler is regulated by adjusting the
temperature of the steam boiler via the
display.
• Since the temperature of saturated
water is proportional to the pressure it
is possible to control the pressure of the
steam boiler via a temperature probe.
Operating Procedure
LaMarzocco 09:30
1
Press and hold the
Password
?????
2
Enter the 5 digit technician password using buttons 1-5 on the group 1 keypad. Once accepted the following appears:
Language
ENGLISH
3
Press the
Steam heat.Type
Temp. Probe
4
or the
button to change the value to Pressure-switch or Temp. Probe then press
Press the
to confirm selection. Normally this value should not be changed
5
button on the group 1 keypad until the following is displayed (approximately 10 seconds)
button on the group 1 keypad until the following appears (about eleven times):
When finished, continue to the next parameter
or press
to exit programming mode.
EN
NOTE: When this parameter is set to “Temp. Probe” an additional parameter named “Steam Temp. Cor. is activated. When
changing from Temp Probe to Pressure Switch it is required to cycle power off and on through the main switch to reset the
steam boiler over temperature alarm.
41
Download PDF
Similar pages
GB-5 Brochure
GS3 Brochure
CMA 3 Grp Schematic
LED Lights Multi-function Display
FB70 Brochure
FB80 Brochure
emblema a - espresso soci
performance at home
LM_scheda tecnica Linea PB.indd
Linea Brochure