Operating and installation instructions Gas hobs

Operating and installation instructions
Gas hobs
To avoid the risk of accidents or damage to the appliance it is essential
to read these instructions before it is installed and used for the first time.
en-GB
M.-Nr. 07 181 160
This hob can be used in countries other than those specified on the appliance.
It is, however, set up for connection to the gas and electricity supplies in the
countries specified. For trouble-free operation of the appliance, it is best to use
it in the countries specified for use.
For use in other countries, please contact Miele in your country.
2
Gas-heated appliances
Safety precautions to take if you smell gas
 Turn off the gas emergency control valve immediately.
This is usually located near the gas meter.
 Eliminate all sources of ignition in a safe manner.
Do not smoke, light cigarette lighters or matches.
 Do not operate electrical lights or switches, i.e. do not switch them "On" or
"Off".
 Open all doors and windows to ventilate the area.
 If the smell of gas persists, evacuate the building.
In the UK you must now:
 Call the Gas Emergency Contact Centre (Tel: 0 800 111 999).
For any gas work in the UK always use a Gas Safe registered engineer.
In other countries please follow relevant country specific procedures on gas.
3
Contents
Warning and Safety instructions.......................................................................... 6
Caring for the environment ................................................................................ 16
Guide to the appliance ........................................................................................ 17
Hob........................................................................................................................ 17
KM 2014 ........................................................................................................... 17
KM 2034 / KM 2035 ......................................................................................... 18
KM 2052 ........................................................................................................... 19
KM 2054 ........................................................................................................... 20
Control knobs........................................................................................................ 21
Burner.................................................................................................................... 22
Accessories supplied ............................................................................................ 23
Using for the first time ........................................................................................ 24
Cleaning the hob for the first time......................................................................... 24
Switching on the hob for the first time .................................................................. 24
Pans ...................................................................................................................... 25
Tips on saving energy ........................................................................................ 27
Operation.............................................................................................................. 28
Switching on.......................................................................................................... 28
Adjusting the flame................................................................................................ 29
Switching off.......................................................................................................... 29
Safety features..................................................................................................... 30
Thermo-electric flame failure monitor ................................................................... 30
Cleaning and care ............................................................................................... 31
Stainless steel trough ............................................................................................ 32
Pan supports ......................................................................................................... 33
Control knobs........................................................................................................ 33
Burner.................................................................................................................... 33
What to do if ... .................................................................................................... 35
Optional accessories .......................................................................................... 37
Safety instructions for installation..................................................................... 38
Safety distances .................................................................................................. 39
Installation notes ................................................................................................. 42
4
Contents
Building-in dimensions ...................................................................................... 43
KM 2014 ................................................................................................................ 43
KM 2034 / KM 2035 .............................................................................................. 44
KM 2052 / KM 2054 .............................................................................................. 45
Installation............................................................................................................ 46
Electrical connection .......................................................................................... 48
Gas connection.................................................................................................... 50
Burner ratings ...................................................................................................... 52
Converting to another gas type ......................................................................... 54
Jet table................................................................................................................. 54
Changing the jets .................................................................................................. 55
Changing the main jets..................................................................................... 55
Changing the small jets .................................................................................... 56
Functional check ................................................................................................... 57
After sales service, data plate, guarantee ........................................................ 58
Product data sheets ........................................................................................... 59
5
Warning and Safety instructions
This hob complies with all relevant safety requirements. Inappropriate use can, however, lead to personal injury and damage to
property.
To avoid the risk of accidents and damage to the hob, please read
these instructions carefully before installation and before using it
for the first time. They contain important notes on installation,
safety, use and maintenance.
Miele cannot be held liable for damage caused by non-compliance
with these instructions.
Keep these instructions in a safe place and ensure that new users
are familiar with the content. Pass them on to any future owner.
6
Warning and Safety instructions
Correct application
 This hob is intended for domestic use and use in other similar environments.
 This hob is not intended for outdoor use.
 It is intended for domestic use only to cook food and keep it
warm. Any other use is not supported by the manufacturer and could
be dangerous.
 People with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge who are not able to use the hob
safely on their own must be supervised whilst using it. They may
only use it unsupervised if they have been shown how to use it safely
and recognise and understand the consequences of incorrect operation.
7
Warning and Safety instructions
Safety with children
 Children under 8 years of age must be kept away from the hob
unless they are constantly supervised.
 Children 8 years and older may only use the hob unsupervised if
they have been shown how to use it in a safe way and can recognise
and understand the consequences of incorrect operation.
 Children must not be allowed to clean the hob unsupervised.
 Please supervise children in the vicinity of the hob and do not let
them play with it.
 The hob gets hot when in use and remains hot for a while after being switched off. Keep children well away from the hob until it has
cooled down and there is no danger of burning.
 Danger of burning.
Do not store anything which might arouse a child's interest in storage areas above or next to the hob. Otherwise they could be tempted into climbing onto the appliance.
 Danger of burning or scalding.
Place pots and pans on the cooking zone in such a way that children
cannot pull them down and burn themselves.
 Danger of suffocation. Packaging, e.g. plastic wrappings, must be
kept out of the reach of babies and children. Whilst playing, children
could become entangled in packaging or pull it over their head and
suffocate.
8
Warning and Safety instructions
Technical safety
 Unauthorised installation, maintenance and repairs can cause
considerable danger for the user. Installation, maintenance and repairs must only be carried out by a Miele authorised technician.
 Do not use a damaged appliance. It could be dangerous. Check
the hob for visible signs of damage.
 Reliable and safe operation of this hob can only be assured if it
has been connected to the mains electricity supply.
 The electrical safety of this hob can only be guaranteed when correctly earthed. It is essential that this standard safety requirement is
met. If in any doubt please have the electrical installation tested by a
qualified electrician.
 To avoid the risk of damage to the hob, make sure that the connection data on the data plate (voltage and frequency) match the
mains electricity supply before connecting it to the mains.
Consult a qualified electrician if in doubt.
 Do not connect the hob to the mains electrical supply by a multisocket adapter or extension lead. These are a fire hazard and do not
guarantee the required safety of the appliance.
 For safety reasons, this hob may only be used after it has been
built in.
 This hob must not be used in a non-stationary location (e.g. on a
ship).
 Never open the casing of the hob.
Touching or tampering with electrical connections or components
and mechanical parts is highly dangerous to the user and can cause
operational faults.
 While the hob is under guarantee, repairs should only be undertaken by a Miele authorised service technician. Otherwise the guarantee is invalidated.
9
Warning and Safety instructions
 Miele can only guarantee the safety of the appliance when genuine original Miele replacement parts are used. Faulty components
must only be replaced by Miele spare parts.
 The hob is not intended for use with an external timer switch or a
remote control system.
 Connection to the gas supply must be carried out by a suitably
qualified gas fitter (e.g. a Gas Safe registered technician in the U.K).
The hob may be connected to the electrical supply by a fused plug
and switched socket. If you wish to connect it to a fused spur connection, or if the plug has been removed or the connection cable is
not supplied with a plug, the hob must be connected to the mains
supply by a suitably qualified electrician.
 If the connection cable is damaged, it must be replaced by a suitably qualified electrician with a special connection cable of type H
05 VV-F (pvc insulated). See "Electrical connection".
 During installation, maintenance and repair work, the hob must be
disconnected from the mains electricity supply. The gas supply must
also be shut off. Depending on country this is done in one of several
different ways:
– the mains fuse has been disconnected, or
– the screw-out fuse is removed (in countries where this is applicable), or
– switch off at the wall socket and withdraw the plug from the
socket. Pull by the plug and not by the mains connection cable to
disconnect from the mains electricity supply.
– the gas inlet valve is closed.
10
Warning and Safety instructions
 Danger of electric shock!
Do not use the hob if it is faulty. Switch it off immediately, disconnect it from the mains electricity supply and the gas supply and contact Miele.
 If the appliance is installed behind a furniture door, do not close
the door while the appliance is in operation. Heat and moisture
would build up behind a closed furniture door, potentially causing
damage to the appliance, the furniture unit and the flooring. Wait until the appliance has cooled down completely before closing the furniture door.
11
Warning and Safety instructions
Correct use
 The appliance gets hot when in use and remains hot for some
time after being switched off. Do not touch the appliance if there is a
possibility that it could still be hot.
 Due to the high temperatures radiated, objects left near the hob
when it is in use could catch fire.
Do not use the hob to heat up the room.
 Oil and fat can overheat and catch fire. Do not leave the hob unattended when cooking with oil and fat. If it does ignite do not attempt
to put the flames out with water.
Disconnect the hob from the mains and use a suitable fire blanket,
saucepan lid, damp towel or similar to smother the flames.
 Flames could set the grease filters of a cooker hood on fire. Do
not flambé under a cooker hood.
 Spray canisters, aerosols and other inflammable substances can
ignite when heated. Therefore do not store such items or substances
in a drawer under the hob. Cutlery inserts must be heat-resistant.
 Do not heat an empty pan.
 Do not heat up food in closed containers e.g. tins or sealed jars
on the hob, as pressure can build up in the container, causing it to
explode.
 Do not cover the hob, e.g. with a hob cover, a cloth or protective
foil. The material could catch fire, shatter or melt if the hob is
switched on by mistake or if residual heat is still present.
 When the hob is switched on either deliberately or by mistake, or
when there is residual heat present, there is the risk of any metal
items left on the hob heating up, with the danger of burning. Depending on the material, other items left on the appliance could also
melt or catch fire. Do not use the hob as a resting place.
12
Warning and Safety instructions
 You could burn yourself on the hot hob. Protect your hands with
heat-resistant pot holders or gloves when handling hot pots and
pans. Do not let them get wet or damp, as this causes heat to transfer through the material more quickly with the risk of scalding or
burning yourself on steam. Be sure to keep all textiles away from the
gas flames. Do not use oversized cloths, tea towels or other similar
materials.
 When using an electrical appliance, e.g. a hand-held food blender,
near the hob, ensure that the cable of the electrical appliance cannot
come into contact with the hot hob. The insulation on the cable
could become damaged.
 Plastic and aluminium foil containers melt at high temperatures.
Do not use plastic or aluminium foil containers on the hob.
 If a cooker hood is installed above the hob, ensure that the burners are always covered with a pan when in use. Otherwise flames
could reach the cooker hood, parts of which could then be damaged
or even set on fire.
 Only light the gas burners after all burner parts have been properly
assembled.
 Pans must be the correct size for the burner they are used on (see
"Suitable Pans"). A pan which is too small will be unstable on the
pan support. If the pan diameter is too large, flames can spread out
to the sides and damage or burn the worktop, wall claddings or surrounding units and also parts of the hob. Miele cannot be held liable
for this type of damage.
 Ensure that the flames from the burner do not spread out beyond
the base and up the sides of the pan.
 Do not use pans with very thin bases on this hob, and never heat
up empty pans as they could get damaged. This could also damage
the appliance.
13
Warning and Safety instructions
 The pan support supplied with the appliance must always be
used. Never place a pan on the burner itself.
 Replace the pan supports carefully to avoid scratching the surface
of the hob.
 Do not use or store flammable materials near this hob.
 Remove splashes of fat and other food debris from the surface of
the hob as soon as possible. These are a fire hazard.
 Avoid allowing liquids or foods containing salt to spill onto the
hob. If salty foods or liquids do get on the hob, they should be removed as soon as possible to avoid the risk of corrosion.
 Using the hob will cause a build-up of heat and moisture in the
room in which it is installed. Ensure that the room has sufficient natural or mechanical means of ventilation, e.g. a cooker hood.
 If the hob is used for very long periods of time, additional ventilation of the room may be necessary, e.g. by opening windows or
doors, or running the cooker hood on the highest setting.
 Do not use roasting dishes, pans or grilling stones that are large
enough to cover more than one burner. The resulting build-up of
heat could damage the hob.
 If the hob has not been used for a long period of time it should be
thoroughly cleaned before it is used again. It is also advisable to
have the appliance tested by a qualified person for safety.
14
Warning and Safety instructions
Cleaning and care
 Do not use a steam cleaning appliance to clean this hob.
The steam could reach electrical components and cause a short circuit.
15
Caring for the environment
Disposal of the packing material
Disposing of your old appliance
The packaging is designed to protect
the appliance from damage during
transportation. The packaging materials
used are selected from materials which
are environmentally friendly for disposal
and should be recycled.
Electrical and electronic appliances often contain valuable materials. They
also contain specific materials, compounds and components, which were
essential for their correct function and
safety. These could be hazardous to human health and to the environment if
disposed of with your domestic waste
or if handled incorrectly. Please do not,
therefore, dispose of your old appliance
with your household waste.
Recycling the packaging reduces the
use of raw materials in the manufacturing process and also reduces the
amount of waste in landfill sites.
Please dispose of it at your local community waste collection / recycling
centre for electrical and electronic appliances, or contact your dealer or
Miele for advice. You are also responsible (by law, depending on country) for
deleting any personal data that may be
stored on the appliance being disposed
of. Please ensure that your old appliance poses no risk to children while being stored prior to disposal.
16
Guide to the appliance
Hob
KM 2014
a Wok burner
Controls knobs for the cooking zones:
b Small burner
e Front right
c Medium burner
f Rear right
d Medium burner
g Rear left
h Front left
17
Guide to the appliance
KM 2034 / KM 2035
a Large burner
Controls knobs for the cooking zones:
b Small burner
f Front right
c Medium burner
g Rear right
d Medium burner
h Middle
e Wok burner
i Rear left
j Front left
18
Guide to the appliance
KM 2052
a Wok burner
Controls knobs for the cooking zones:
b Small burner
f Front right
c Large burner
g Rear right
d Medium burner
h Middle
e Medium burner
i Rear left
j Front left
19
Guide to the appliance
KM 2054
a Wok burner
Controls knobs for the cooking zones:
b Small burner
f Front right
c Large burner
g Rear right
d Wok burner
h Middle
e Medium burner
i Rear left
j Front left
20
Guide to the appliance
Control knobs
Small, medium and large burners
Symbol
Description

Burner off, the gas supply is turned off

Largest flame

Smallest flame
Wok burner
Symbol
Description

Burner off, the gas supply is turned off

Largest flame: inner and outer burner on highest setting.

Large flame: outer burner on lowest setting, inner burner on highest setting.

Small flame: outer burner off, inner burner on highest setting.

Smallest flame: outer burner off, inner burner on lowest setting.
21
Guide to the appliance
Burner
Small, medium and large burners
Wok burner
a Burner ring (wok burner)
b Burner cap
c Burner head
d Burner base
e Thermocouple
f Ignitor
22
Guide to the appliance
Accessories supplied
The accessories supplied with your appliance as well as a range of optional
ones are available to order from Miele
(see "Optional accessories").
Wok ring
The wok ring supplied gives additional
stability to the wok, especially to woks
with a rounded base.
23
Using for the first time
 Please stick the extra data plate for
the appliance supplied with this documentation in the space provided in
the "After sales service, data plate,
guarantee" section of this booklet.
 Remove any protective wrapping and
stickers.
Cleaning the hob for the first
time
 Before using for the first time, clean
the hob with a damp cloth only and
then wipe dry.
 Clean all removable parts of the burners with a solution of warm water and
a small amount of washing-up liquid
applied with a soft sponge. Dry all
parts thoroughly after cleaning and
then reassemble the burners (see
"Cleaning and care").
24
Switching on the hob for the
first time
The metal components have a protective coating which when heated for the
first time will give off a slight smell and
possibly some vapours.
The smell and any vapours given off do
not indicate a faulty connection or appliance and they are not hazardous to
health.
Pans
Minimum pan base diameter
Burner
Ø cm
Small burner
10
Medium burner
12
Large burner
14
Wok burner
14
Maximum diameter at top of pan
Burner
Ø cm
Small burner
22
Medium burner
22
Large burner
24
Wok burner
24
– Select cookware that fits the size of
the burner:
Large diameter = large burner
Small diameter = small burner.
– Refer to the chart above and ensure
that the pan diameter falls within the
minimum and maximum diameters
given for the burner you are using. If
the pan diameter is too large, flames
can spread out to the sides and damage or burn the worktop, wall claddings or surrounding units and also
parts of the hob or other appliances.
Pans which are too small for the pan
supports, or pans which do not sit
securely on the pan supports, are
dangerous and should not be used.
– Remember when purchasing new
pans that manufacturers usually refer
to the diameter at the top of the pan
in their documentation, and not to the
base diameter.
– Any heat-resistant pans can be used
on a gas burner.
– Pans with thick bases are preferable
as these distribute heat more evenly.
With thin bases, there is a danger of
food overheating in places. Stir the
food frequently.
– Always place cookware on the pan
support supplied with the appliance.
Never place it directly on the burner.
– Position the cookware centrally on
the pan support so that it sits securely and cannot tip. A little movement is quite normal and not a cause
for concern.
– Do not use pots or pans that have
bases with pronounced edges.
– Unlike pans that are used on an electric hob, the bottom of pans used on
a gas hob do not have to be flat to
deliver good cooking results.
25
Pans
Wok ring
 Use the wok ring supplied to give additional stability to pans, especially to
woks with a rounded base.
 Place the wok ring on the pan support so that it sits securely in position
and cannot move (see diagram).
The wok is unique among cookware in
that it has a small base diameter and a
large rim diameter (usually 35-40 cm).
Wok pans are ideal for use on the wok
burner.
26
Tips on saving energy
– Use a pan lid whenever possible to
minimize heat loss.
– Wide, shallow pans are preferable to
tall, narrow ones. They will heat up
faster.
– Cook with as little water as possible.
– Reduce the size of the flame once the
water has come to the boil or the oil
is hot enough to fry in.
– Use a pressure cooker to reduce
cooking times.
27
Operation
 Fire hazard.
Switching on during a power outage
Do not leave the appliance unattended whilst it is being used.
If there is an interruption to the electricity supply, the gas can be ignited
manually, e.g. with a match.
Switching on
 The control for the burner must be
pressed in and turned anti-clockwise
to the large flame symbol to switch
on. The ignitor will "click" and ignite
the gas.
When a control knob is activated, a
spark is developed automatically at all
rings. This is normal and does not indicate a defect.
 When a flame is visible, keep the
control knob pressed in for
5-10 seconds, and then let it go.
 If the burner does not ignite, turn the
control knob back to "". Air the room
or wait at least one minute before trying again. Try keeping the control
knob pressed in for a little longer the
next time.
 If the burner does not ignite the
second time, turn the control knob
back to "" and see "Problem solving
guide".
28
 Press in the relevant control and turn
it anti-clockwise to the large flame
symbol.
 Hold the control pressed in and light
the gas at the burner with a match.
 Keep the control pressed in for a further 5-10 seconds and then release it.
Operation
Adjusting the flame
Switching off
The burners can be regulated at any
level between the strongest and weakest flame.
 Turn the control clockwise to position
"".
As the outer part of the flame is much
hotter than the centre, the tips of the
flames should stay beneath the pan
base. Flame tips which extend beyond
the sides of the pan merely warm up
the air in the room and can also damage pan handles and increase the
danger of injury.
This stops the flow of gas and the flame
goes out.
 Adjust the flame so that it does not
spread out beyond the sides of the
pan.
Wok burner
Depending on the type of control knob,
there may be a stopper between the
low and high settings at the 6 o'clock
position.
 Press the control knob down lightly to
move past this resistance.
29
Safety features
Thermo-electric flame failure
monitor
This hob has a thermo-electric flame
failure monitor. If the flame goes out, for
example because food has boiled over
or if there has been a sudden draught,
the supply of gas to the burner will be
cut off. This will prevent any gas escaping. To use the burner again, turn the
control knob to "".
The thermo-electric flame failure monitor operates independently from the
electricity supply. This means that it
will still work if the hob is used during
a power cut.
30
Cleaning and care
 Danger of burning.
Unsuitable cleaning agents
The burners must be switched off.
The hob needs to cool down.
To avoid damaging the surfaces of your
appliance, do not use:
 Danger of injury.
– cleaning agents containing soda, alkalines, ammonia, acids or chlorides
The steam from a steam cleaning appliance could reach electrical components and cause a short circuit.
Do not use a steam cleaner to clean
the hob.
The use of unsuitable cleaning
agents can cause the surfaces to
discolour or alter.
All surfaces are susceptible to
scratching.
Remove any residual cleaning agent
immediately.
– cleaning agents containing descaling
agents
– stain or rust removers
– abrasive cleaning agents, e.g.
powder cleaners and cream cleaners
– solvent-based cleaning agents
– dishwasher cleaner
– grill and oven cleaners
– glass cleaning agents
– hard, abrasive brushes or sponges,
e.g. pot scourers, brushes or
sponges which have been previously
used with abrasive cleaning agents
– melamine eraser blocks
31
Cleaning and care
The surfaces of the burner components and pan supports will become
more matt with time. This is completely normal and does not indicate
damage to the material.
 The entire hob should be cleaned
after each use.
 Stubborn soiling should be soaked
first.
 Dry the hob after using water to clean
it. This helps prevent limescale deposits.
Tip: Food that has boiled over onto a
hot hob can result in discolouration on
the burner components. Immediately
remove all spilled food and all salt or
sugar splatters.
Stainless steel trough
Do not clean the area between the
hob and the worktop with sharp,
pointed objects.
This could damage the seals.
Soiling, particularly salty food or liquid and olive oil, can cause damage
if left on the printed surfaces for a
long time.
Remove any soiling which comes
into contact with the printed symbols
straight away.
Stainless steel cleaning agents rub
off the printed symbols.
Do not use stainless steel cleaning
agents on printed symbols.
 Clean stainless steel surfaces with a
solution of warm water and a small
amount of washing-up liquid applied
32
with a soft sponge. In the case of
stubborn dried-on soiling, soak first.
If necessary, the rough side of nonscouring sponge can be used.
 Finally, dry with a clean soft cloth.
Tip: The Miele conditioning agent for
stainless steel can be used after cleaning to help keep your appliance looking
good (see "Optional accessories"). Apply sparingly with a soft cloth following
the instructions on the packaging.
Cleaning and care
Pan supports
Do not clean the pan supports in a
dishwasher.
 Remove the pan supports.
 Clean the pan supports with a solution of warm water and a little washing-up liquid applied with a soft
sponge. Stubborn soiling should be
soaked first.
 After cleaning, dry the pan supports
thoroughly with a clean cloth.
Control knobs
The control knobs are not dishwasher safe.
The control knobs should only be
cleaned by hand.
The control knobs may become discoloured if they are not cleaned regularly.
 Clean the control knobs using a solution of warm water and a little washing-up liquid applied with a soft
sponge.
Burner
Do not clean any parts of the burner
in a dishwasher.
 The burner should be dismantled and
then cleaned by hand using a solution of warm water and a little washing-up liquid applied with a soft
sponge.
 Parts of the burner that cannot be removed should be wiped clean with a
damp cloth only.
 The ignitor and thermocouple should
be very carefully wiped clean using a
well wrung out cloth.
Do not let the ignitor get wet. If it gets
wet, it will not spark.
 After cleaning, dry all surfaces with a
clean cloth. Make sure that the flame
slits are clean and completely dry.
The surfaces of the burner caps will
become more matt with time. This is
quite normal and does not indicate
damage to the burner caps. Nor will
affect the operation of the hob.
33
Cleaning and care
Assembling the small, medium and
large burners
Assembling the wok burner
 Place the burner head  onto the
burner base  so that the thermocouple , the ignitor  and the retaining pins  fit into their respective
holes in the burner head.
 Position the burner cap  onto the
burner head  so that the retaining
pins fit into their respective recesses.
Gently twist the burner cap clockwise
or anti-clockwise until it locks into
position. When correctly positioned,
the burner cap will not slide about.
Ensure parts are reassembled in the
correct order.
 Place the burner head  on the
burner base  so that the holes fit
over the jets in the burner base and
the locating bar sits in the notch. If
the burner head is in the correct position, it will not move about.
 Replace the burner ring  so that the
notches are in line above each other.
 Replace the burner cap .
Ensure parts are reassembled in the
correct order.
34
What to do if ...
With the aid of the following guide, minor problems can be easily corrected
without contacting Miele.
If having followed the suggestions below, you still cannot resolve the problem,
please contact Miele (see end of this booklet for contact details).
 Danger of injury. Installation, maintenance and repairs to electrical appliances must only be carried out by a suitably qualified and competent person in
strict accordance with current local and national safety regulations.
Do not open the casing of the appliance.
Repairs and other work by unqualified persons could be dangerous and Miele
cannot be held liable for unauthorised work.
Problem
Cause and remedy
The burners do not igThere could be air lock in the gas pipe.
nite when the hob is be-  You may need to make several attempts before the
ing used for the first
burner ignites successfully.
time or after it has been
out of use for a longer
period.
The burner does not ignite after several attempts.
There may be a technical fault.
 Turn all of the controls clockwise to "" and interrupt the power supply to the hob for a few
seconds.
The burner is not correctly assembled.
 Assemble the burner correctly.
The gas shut-off valve is closed.
 Open the gas shut-off valve.
The burner is wet and/or dirty.
 Clean and dry the burner.
The flame slits are blocked and/or wet.
 Clean and dry the flame slits.
The gas flame goes out
after being lit.
The flames do not touch the thermocouple and the
burner does not get hot enough:
The burner parts are not positioned correctly.
 Position the burner parts correctly.
There is soiling on the thermocouple.
 Remove any soiling.
35
What to do if ...
Problem
Cause and remedy
The flame suddenly
looks different.
The burner parts are not positioned correctly.
 Position the burner parts correctly.
The burner head or the holes in the burner cap are
dirty.
 Remove any soiling.
The gas flame goes out
during use.
The burner parts are not positioned correctly.
 Position the burner parts correctly.
The ignitor on the
burner does not spark.
The mains fuse has tripped.
 You may need to contact a qualified electrician or
Miele.
There is food residue stuck between the ignitor and
the burner cap.
There is food residue on the thermocouple.
 Remove any soiling (See "Cleaning and care").
36
Optional accessories
Miele offer a comprehensive range of
useful accessories as well as cleaning
and conditioning products for your
Miele appliances.
These products can be ordered through
the Miele Webshop.
These can also be ordered from Miele
(see end of this booklet for contact details) or from your Miele dealer.
Microfibre cloth
Removes finger marks and light soiling
Stainless steel conditioning
agent 250 ml
Removes water marks, flecks and finger
prints. Helps keep the appliance looking
good for longer.
37
Safety instructions for installation
Fit the wall units and cooker hood before fitting the hob to avoid damaging the
hob.
 The veneer or laminate coatings of worktops (or adjacent kitchen
units) must be treated with 100 °C heat-resistant adhesive which will
not dissolve or distort. Any backmoulds must be of heat-resistant
material.
 The hob must not be installed over a fridge, fridge-freezer, freezer,
dishwasher, washing machine, washer-dryer or tumble dryer.
 A gas hob must not be installed directly next to a deep fat fryer as
the gas flames could ignite the fat in the fryer. It is essential to maintain a distance of at least 300 mm between these two appliances.
 When installing the hob, make sure that the gas pipe and electrical connection cable cannot come into contact with hot appliance
parts.
 The electrical cable and any flexible gas connection pipes must be
installed in such a way so that they do not come into contact with
any moving kitchen parts (e.g. a drawer), and cannot become
trapped.
 Observe carefully the safety clearances listed on the following
pages.
All dimensions are given in mm.
38
Safety distances
Safety distance above the hob
A minimum safety distance must be
maintained between the appliance and
the cooker hood above it. See the
cooker hood manufacturer's operating
and installation instructions for details.
If the manufacturer's instructions are
not available for the cooker hood or if
any flammable objects (e.g. utensil rails,
wall units etc) are installed above the
hob a minimum safety distance of at
least 760 mm must be maintained
between them and the appliance below.
When two or more appliances which
have different safety distances are
installed together below a cooker
hood, you should observe the
greatest safety distance.
39
Safety distances
Safety distances to the sides
and back of the hob
Ideally the hob should be installed with
plenty of space on either side. There
may be a wall at the rear or a tall unit or
wall on one side (right or left) (see illustrations).
 Minimum distance between the back
of the worktop cut-out and the rear
edge of the worktop:
50 mm
Not allowed
 Minimum distance between the
worktop cut-out and a wall or tall unit to
the right of it:
100 mm.
 Minimum distance between the
worktop cut-out and a wall or tall unit to
the left of it:
100 mm.
Recommended
Not recommended
Not recommended
40
Safety distances
Safety distance when installing the appliance near a wall with
additional niche cladding
A minimum safety distance must be maintained between the worktop cut-out and
any niche cladding to protect it from heat damage.
If the niche cladding is made from a combustible material (e.g. wood) a minimum
safety distance  of 50 mm must be maintained between the cut-out and the
cladding.
If the niche cladding is made from a non-combustible material (e.g. metal, natural
stone, ceramic tiles) the minimum safety distance  between the cut-out and the
cladding will be 50 mm less the thickness of the cladding.
Example: 15 mm niche cladding
50 mm - 15 mm = minimum safety distance of 35 mm
Flush-fitted hobs
Hob with frame or bevelled edge
a Masonry
b Niche cladding dimension x = thickness of the niche cladding material
c Worktop
d Worktop cut-out
e Minimum distance to
combustible materials 50 mm
non-combustible materials 50 mm - dimension x
41
Installation notes
Seal between the hob and the
worktop
Do not use sealant between the hob
and the worktop. This could result in
damage to the hob or the worktop if
the hob ever needs to be removed
for servicing.
The sealing strip under the edge of
the top part of the appliance
provides a sufficient seal for the
worktop.
42
Tiled worktop
Grout lines  and the hatched area underneath the hob frame must be
smooth and even. If they are not the
hob will not sit flush with the worktop
and the sealing strip underneath the
hob will not provide a good seal
between the hob and the worktop.
Building-in dimensions
KM 2014
520
650
35
15
b
c
4
ßR
05
0
480
+
- 49
0
60
-
1
5
a
0
d
30
54
217
75
3
196
24
c
a Front
b Casing depth
c Gas connection R ¹/₂ - ISO 7-1 (DIN EN 10226)
d Mains connection box with mains connection cable, L = 2000 mm
43
Building-in dimensions
KM 2034 / KM 2035
520
750
35
15
b
c
4
ßR
0 50
480
- 49
0
0
56
+- 1
a
0
03
d
54
217
75
196
3
24
c
a Front
b Casing depth
c Gas connection R ¹/₂ - ISO 7-1 (DIN EN 10226)
d Mains connection box with mains connection cable, L = 2000 mm
44
Building-in dimensions
KM 2052 / KM 2054
520
900
35
15
b
c
4
ßR
0 50
480
- 49
0
+- 1
0
6
8
d
a
54
0
03
217
25
39
196
3
c
a Front
b Casing depth
c Gas connection R ¹/₂ - ISO 7-1 (DIN EN 10226)
d Mains connection box with mains connection cable, L = 2000 mm
45
Installation
Preparing the worktop
Installing the hob
 Make the worktop cut-out as shown
in the building-in diagram. Observe
the safety distances (see "Safety distances").
 Feed the mains connection cable
down through the cut-out.
 Seal the cut surfaces with a suitable
sealant to avoid swelling caused by
moisture. The sealant must be heatresistant.
Make sure that the sealant does not
come into contact with the top of the
worktop.
The seal underneath the hob will hold
it securely in the cut-out. Any gap
between the frame and worktop will
reduce with time.
 Place the hob centrally in the cut-out.
When doing this, make sure that the
seal under the hob sits flush with the
worktop on all sides. This is important to ensure an effective seal all
round.
If the seal does not meet the worktop
correctly on the corners, the corner radius (≤ R4) can be carefully scribed to
suit.
Do not use sealant (e.g. silicone).
 Connect the hob to the mains.
 Connect the hob to the gas supply
(see "Gas connection").
46
Installation
Securing the hob
Functional check
 After installing the hob, ignite all
burners to check that they are operating correctly:
– The flame must not go out on the
lowest setting, or when the control is
turned quickly from the highest to the
lowest setting.
– On the highest setting, the flame
must have a distinctive and visible
core.
 Secure the hob using the brackets 
supplied.
47
Electrical connection
All electrical work must be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations (BS
7671 in the UK). Connection must be
made via a switched socket. This will
make it easier for service technicians
should the appliance need to be repaired. The electrical socket must be
easily accessible after installation.
Total power rating
See data plate
Connection
AC 230 V, 50 Hz
The connection data is quoted on the
dataplate. It must match the household
supply.
 Danger of injury.
Residual current device
Miele cannot be held liable for unauthorised installation, maintenance
and repair work as this can be dangerous to users.
Miele cannot be held liable for damage or injury caused by incorrect installation, maintenance or repair
work, or by an inadequate or faulty
earthing system (e.g. electric shock).
If the plug is removed from the connection cable or if the cable is supplied without a plug, the appliance
must be connected to the electrical
supply by a suitably qualified electrician.
If the switched socket is not accessible after installation, or if the appliance is to be hard-wired, an additional means of disconnection must
be provided for all poles. When
switched off, there must be an allpole contact gap of at least 3 mm in
the switch (including switch, fuses
and relays). Connection data is
shown on the data plate. It must
match the mains electrical supply.
After installation ensure that all electrical components are shielded and
cannot be accessed by users.
For extra safety, it is advisable to protect the appliance with a suitable residual current device (RCD) with a trip
range of 30 mA.
48
WARNING
THIS APPLIANCE MUST BE
EARTHED
Electrical connection
Disconnecting from the mains
Replacing the mains cable
 Danger of electric shock.
 Danger of electric shock.
After disconnection, ensure the appliance cannot be switched back on
by mistake.
The mains connection cable must be
replaced by a suitably qualified and
competent person in accordance
with current local and national safety
regulations. (e.g. BS 7671 in the UK).
To disconnect the appliance from the
mains power supply, do one of the following depending on installation:
Safety fuses
 Completely remove fuses
Automatic circuit breakers
 Press the (red) button until the middle
(black) button springs out.
If the mains cable needs to be replaced
it must be replaced with a special connection cable, type H 05 VV-F (PVC-insulated), available from Miele.
The connection data is quoted on the
data plate.
Built-in circuit breakers
 Circuit breakers, type B or C: switch
the on-off switch from 1 (on) to 0 (off).
Residual current device (RCD)
 Switch the main switch from 1 (on) to
0 (off) or press the test button.
49
Gas connection
For any gas work in the UK always
use a Gas Safe registered engineer.
 Connection to the gas supply, or
conversion to a different gas type,
may only be undertaken by an approved and registered gas installer.
The installer is responsible for ensuring that the appliance functions correctly when installed.
The gas connection must be installed so that connection can be
made either from inside or outside
the kitchen unit. The isolating valve
must be easily accessible and visible
(by opening the kitchen door if necessary).
Check with your local gas supplier
about the type of gas its calorific
value and compare this information
with the type of gas quoted on the
appliance's data plate.
This hob is not connected to an exhaust flue.
When installing and connecting the
appliance please observe all relevant
installation instructions and ensure it
has adequate ventilation once installed.
50
Connection to the gas supply must
be carried out in strict accordance
with local and national safety regulations (e.g. Gas Safe in the UK). Every
appliance should have its own easily
accessible isolating valve and test
point.
Any special local conditions relating
to gas installations as well as building regulations must also be observed.
Gas connections, pipes and connection cables can suffer damage if exposed to heat from the hob.
After installation make sure that
neither the gas pipe nor the mains
cable can come into contact with hot
parts of the appliance and that the
gas pipe and connections on the hob
cannot come into contact with hot
gas exhaust.
Flexible gas pipes (in countries
where permitted) can be damaged
by incorrect routing.
Attach flexible gas pipes in such a
way so that they do not come into
contact with any moving kitchen
parts (e.g. a drawer) and are not exposed to mechanical stress.
The hob must be set for local gas
conditions and the gas connection
must undergo a leakage test.
Gas connection
This hob is a class 3 appliance and is
suitable for use with natural gas or liquid gas.
Category in acc. with EN 30
United Kingdom
GB II 2 H3 +20 mbar, 28-30/37 mbar
Ireland
IE II 2 H 3+20 mbar, 28-30/37 mbar
Depending on country of destination
this appliance is set up for connection
to natural or liquid gas. See adhesive label on the appliance.
Depending on country, a set of jets for
conversion to an alternative type of gas
may be included with the hob. Please
contact your supplier or Miele for the
appropriate conversion jets if necessary. Conversion to another type of gas
is described under "Conversion to another type of gas".
a Connection with test point specifically for GB
b 90° bend
Connection with test point specifically for GB and 90 ° bend.
Connecting the hob
The hob is supplied with a conical ¹/₂"
gas connection point for connection to
one of the following:
– Rigid connection with isolation valve
– Flexible connection in accordance
with DIN 3383 Part 1, maximum
length 2000 mm. (Not for the UK!)
Unsuitable sealants may not be leakproof.
Connections must be sealed using
appropriate sealant.
51
Burner ratings
Nominal ratings for KM 2014
Burner
Gas type
Highest setting
Lowest setting
kW
g/h
kW
Small burner
Natural gas H
Liquid gas
1.0
1.0
–
73
0.25
0.25
Medium
burner
Natural gas H
Liquid gas
1.75
1.75
–
127
0.35
0.35
Wok
Natural gas H
Liquid gas
4.2
4.2
–
306
0.3
0.3
Total
Natural gas H
Liquid gas
8.7
8.7
–
633
Nominal ratings for KM 2034 / KM 2035 / KM 2052
Burner
Gas type
Highest setting
Lowest setting
kW
g/h
kW
Small burner
Natural gas H
Liquid gas
1.0
1.0
–
73
0.25
0.25
Medium
burner
Natural gas H
Liquid gas
1.75
1.75
–
127
0.35
0.35
Large burner
Natural gas H
Liquid gas
2.6
2.6
–
189
0.5
0.6
Wok
Natural gas H
Liquid gas
4.2
4.2
–
306
0.3
0.3
Total
Natural gas H
Liquid gas
11.3
11.3
–
822
52
Burner ratings
Nominal ratings for KM 2054
Burner
Gas type
Highest setting
Lowest setting
kW
g/h
kW
Small burner
Natural gas H
Liquid gas
1.0
1.0
–
73
0.25
0.25
Medium
burner
Natural gas H
Liquid gas
1.75
1.75
–
127
0.35
0.35
Large burner
Natural gas H
Liquid gas
2.6
2.6
–
189
0.5
0.6
Wok
Natural gas H
Liquid gas
4.2
4.2
–
306
0.3
0.3
Total
Natural gas H
Liquid gas
13.75
13.75
–
1001
53
Converting to another gas type
 Conversion from one type of gas
Jet table
to another, should only be undertaken by an approved and registered
gas installer in strict accordance with
current local and national safety and
building regulations.
Disconnect the hob from the electricity supply and turn off the gas supply.
The jet markings refer to a ¹/₁₀₀ mm
bore diameter.
When converting to another type of
gas, both the main and small jets
need to be changed.

Burner
Main jet
Small jet
Small
0.69
0.39
Medium
0.95
0.42
Large
1.10
0.54
Wok
0.97 / 0.72
0.88 / 0.42
Small
0.50
0.27
Medium
0.63
0.32
Large
0.78
0.40
Wok
0.64 / 0.46
0.52 / 0.27
Natural gas H
Liquid gas
54
Converting to another gas type
Changing the jets
Wok burner
 Disconnect the hob from the electricity supply and turn off the gas supply.
Changing the main jets
Small, medium and large burners
The burner cap  is locked on these
burners. You must turn it clockwise or
anti-clockwise to remove it.
 Remove the pan support, burner
cap  and burner head .
 Using an M7 socket spanner, unscrew the main jet .
 Fit the correct jets securely (see jet
table).
 Secure the jets against inadvertent
loosening with sealing wax.
 Remove the burner cap , burner
ring  and burner head .
 Using a socket spanner (M7), unscrew the main jets  (larger diameter) and  (smaller diameter).
 Fit the correct jets securely (see jet
table).
 Secure the jets against inadvertent
loosening with sealing wax.
55
Converting to another gas type
Changing the small jets
To change the small jets, the burner
fixing screws must first be loosened
and the upper section of the appliance
removed.
 Pull the control knobs off.
Small, medium and large burners
a
 Remove the burner components.
 Undo the screws.
 Lift the top of the appliance off.
b
 Remove the ignition switch .
 Using a small screwdriver, unscrew
the small jet  in the gas fitting.
 Pull out the jet with a pair of pliers.
 Fit the correct jets securely (see jet
table).
 Secure the jets against inadvertent
loosening with sealing wax.
56
Converting to another gas type
Wok burner
– The flame must not go out on the
lowest setting, or when the control is
turned quickly from the highest to the
lowest setting.
– On the highest setting, the flame
must have a distinctive and visible
core.
a
 Adhere the label supplied with the
jets, stating the type of gas being
used.
c
b
b Small jet with smaller diameter
(e.g. for LPG: 0,27)
c Small jet with larger diameter
(e.g. for LPG: 0,52)
 Remove the ignition switch .
 Using a small screwdriver, unscrew
the two small jets in the gas fitting.
 Pull out the jets with a pair of pliers.
 Fit the correct jets securely (see jet
table).
 Secure the jets against inadvertent
loosening with sealing wax.
Functional check
 Check all gas fittings for leaks.
 Reassemble the hob.
 Ignite all burners to check that they
are operating correctly.
57
After sales service, data plate, guarantee
After sales service
In the event of any faults which you cannot easily remedy, please contact
– your Miele Dealer, or
– Miele Service.
See end of this booklet for contact details.
Please note that telephone calls may be monitored and recorded for training purposes.
N.B. A call-out charge will be applied to service visits where the problem could
have been resolved as described in these instructions.
When contacting your Dealer or Miele, please quote the model and serial number
of your appliance.
Data plate
Space in which to stick the extra data plate supplied with the appliance. Ensure
that the model number is the same as the one on the back page of these instructions.
Guarantee: UK
The appliance is guaranteed for 2 years from the date of purchase.
In the UK, you must activate your cover by calling 0330 160 6640 or registering
online at www.miele.co.uk.
Guarantee: Other countries
For information on the appliance guarantee specific to your country please contact
Miele. See end of this booklet for contact details.
58
Product data sheets
The following data sheets apply to the models described in this operating instruction manual.
Information for domestic gas-fired hobs
In acc. with regulation (EU) No. 66/2014
MIELE
Model name / identifier
KM 2014
Number of gas burners
4
Energy efficiency per gas burner (EEgas burner)
1. = 52,7
3. = 56,5
4. = 56,5
Energy efficiency for the gas hob calculated per kg 55,2
(EEgas hob)
Information for domestic gas-fired hobs
In acc. with regulation (EU) No. 66/2014
MIELE
Model name / identifier
KM 2034
Number of gas burners
5
Energy efficiency per gas burner (EEgas burner)
1. = 54,7
3. = 52,7
4. = 56,5
5. = 56,5
Energy efficiency for the gas hob calculated per kg 55,1
(EEgas hob)
Information for domestic gas-fired hobs
In acc. with regulation (EU) No. 66/2014
MIELE
Model name / identifier
KM 2035
Number of gas burners
5
Energy efficiency per gas burner (EEgas burner)
1. = 54,7
3. = 52,7
4. = 56,5
5. = 56,5
Energy efficiency for the gas hob calculated per kg 55,1
(EEgas hob)
59
Product data sheets
Information for domestic gas-fired hobs
In acc. with regulation (EU) No. 66/2014
MIELE
Model name / identifier
KM 2052
Number of gas burners
5
Energy efficiency per gas burner (EEgas burner)
1. = 52,7
3. = 54,7
4. = 56,5
5. = 56,5
Energy efficiency for the gas hob calculated per kg 55,1
(EEgas hob)
Information for domestic gas-fired hobs
In acc. with regulation (EU) No. 66/2014
MIELE
Model name / identifier
KM 2054
Number of gas burners
5
Energy efficiency per gas burner (EEgas burner)
1. = 52,7
3. = 54,7
4. = 56,5
5. = 56,5
Energy efficiency for the gas hob calculated per kg 54,2
(EEgas hob)
60
United Kingdom
Miele Co. Ltd.
Fairacres, Marcham Road
Abingdon, Oxon, OX14 1TW
Customer Contact Centre Tel: 0330 160 6600
E-mail: mielecare@miele.co.uk
Internet: www.miele.co.uk
Australia
Miele Australia Pty. Ltd.
ACN 005 635 398
ABN 96 005 635 398
1 Gilbert Park Drive, Knoxfield, VIC 3180
Tel: 1300 464 353
Internet: www.miele.com.au
China
Miele (Shanghai) Trading Ltd.
1-3 Floor, No. 82 Shi Men Yi Road
Jing' an District
200040 Shanghai, PRC
Tel: +86 21 6157 3500, Fax: +86 21 6157 3511
E-mail: info@miele.cn, Internet: www.miele.cn
Miele (Hong Kong) Limited
41/F - 4101, Manhattan Place
23 Wang Tai Road
Kowloon Bay, Hong Kong
Tel: (852) 2610 1025, Fax: (852) 3579 1404
Email: customerservices@miele.com.hk
Website: www.miele.hk
India
Miele India Pvt. Ltd.
Ground Floor, Copia Corporate Suites
Plot No. 9, Jasola, New Delhi - 110025
Tel: 011-46 900 000, Fax: 011-46 900 001
E-mail: customercare@miele.in, Internet: www.miele.in
Ireland
Miele Ireland Ltd.
2024 Bianconi Avenue
Citywest Business Campus, Dublin 24
Tel: (01) 461 07 10, Fax: (01) 461 07 97
E-Mail: info@miele.ie, Internet: www.miele.ie
Manufacturer: Miele & Cie. KG
Carl-Miele-Straße 29, 33332 Gütersloh, Germany
Malaysia
Miele Sdn Bhd
Suite 12-2, Level 12
Menara Sapura Kencana Petroleum
Solaris Dutamas No. 1, Jalan Dutamas 1
50480 Kuala Lumpur, Malaysia
Phone: +603-6209-0288
Fax: +603-6205-3768
New Zealand
Miele New Zealand Limited
IRD 98 463 631
Level 2, 10 College Hill
Freemans Bay, Auckland 1011, NZ
Tel: 0800 464 353
Internet: www.miele.co.nz
Singapore
Miele Pte. Ltd.
163 Penang Road
# 04 - 03 Winsland House II
Singapore 238463
Tel: +65 6735 1191, Fax: +65 6735 1161
E-Mail: info@miele.com.sg
Internet: www.miele.sg
South Africa
Miele (Pty) Ltd
63 Peter Place, Bryanston 2194
P.O. Box 69434, Bryanston 2021
Tel: (011) 875 9000, Fax: (011) 875 9035
E-mail: info@miele.co.za
Internet: www.miele.co.za
United Arab Emirates
Miele Appliances Ltd.
Gold & Diamond Park
Office No. 217-6, Sheikh Zayed Road
P.O. Box 11 47 82 - Dubai
Tel. +971 4 3044 999
Fax. +971 4 3418 852
800-MIELE (64353)
E-Mail: info@miele.ae
Website: www.miele.ae
KM 2014 / KM 2034 / KM 2035 / KM 2052 / KM 2054

en-GB
M.-Nr. 07 181 160 / 08
Download PDF
Similar pages
CDA HG6320
Candy PV 750 SX
Candy PSP 750 ZEN
Smeg GP75ES
Smeg PGF644 hob
Smeg PGF75-4
Gorenje G760AX1 Product Specification
Smeg PGF954 hob
Smeg PS906-4
Stoves S5-G600CW