Operating and installation instructions
Gas hob
To avoid the risk of accidents or damage to the appliance it is essential
to read these instructions before it is installed and used for the first time.
en-HK
M.-Nr. 10 829 880
This hob can be used in countries other than those specified on the appliance.
It is, however, set up for connection to the gas and electricity supplies in the
countries specified. For trouble-free operation of the appliance, it is best to use
it in the countries specified for use.
For use in other countries, please contact Miele in your country.
2
Gas-heated appliances
Safety precautions to take if you smell gas
 Turn off the gas emergency control valve immediately.
This is usually located near the gas meter.
 Eliminate all sources of ignition in a safe manner.
Do not smoke, light cigarette lighters or matches.
 Do not operate electrical lights or switches, i.e. do not switch them "On" or
"Off".
 Open all doors and windows to ventilate the area.
 If the smell of gas persists, evacuate the building.
3
Contents
Warning and Safety instructions.......................................................................... 6
Caring for the environment ................................................................................ 15
Guide to the appliance ........................................................................................ 16
Hob........................................................................................................................ 16
Control knob.......................................................................................................... 17
Burner.................................................................................................................... 18
Before using for the first time ............................................................................ 19
Cleaning the hob for the first time......................................................................... 19
Switching on the hob for the first time .................................................................. 19
Pans ...................................................................................................................... 20
Tips on saving energy ........................................................................................ 21
Operation.............................................................................................................. 22
Switching on.......................................................................................................... 22
Adjusting the flame................................................................................................ 22
Switching off.......................................................................................................... 22
Safety features..................................................................................................... 23
Thermo-electric flame failure monitor ................................................................... 23
Cleaning and care ............................................................................................... 24
Stainless steel frame/control panel ....................................................................... 25
Control knobs........................................................................................................ 25
Stainless steel trough ............................................................................................ 25
Pan supports ......................................................................................................... 26
Burner.................................................................................................................... 26
Problem solving guide ........................................................................................ 28
Optional accessories .......................................................................................... 30
Safety instructions for installation..................................................................... 31
Safety distances .................................................................................................. 32
Installation notes ................................................................................................. 35
Building-in dimensions ...................................................................................... 36
Building-in several CombiSets ........................................................................... 37
Installation............................................................................................................ 39
4
Contents
Electrical connection .......................................................................................... 43
Gas connection.................................................................................................... 45
Burner ratings ...................................................................................................... 47
After sales service............................................................................................... 48
Contact in case of malfunction ............................................................................. 48
Data plate .............................................................................................................. 48
Guarantee.............................................................................................................. 48
Technical Data ..................................................................................................... 49
5
Warning and Safety instructions
This hob complies with all current local safety requirements.
Inappropriate use can, however, lead to personal injury and
damage to property.
To avoid the risk of accidents and damage to the hob, please read
these instructions carefully before installation and before using it
for the first time. They contain important notes on installation,
safety, use and maintenance.
Miele cannot be held liable for damage caused by non-compliance
with these instructions.
Keep these instructions in a safe place and ensure that new users
are familiar with the content. Pass them on to any future owner.
6
Warning and Safety instructions
Correct application
 This hob is intended for domestic use and use in other similar
environments.
 This hob is not intended for outdoor use.
 It is intended for domestic use only to cook food and keep it
warm. Any other use is not supported by the manufacturer and could
be dangerous.
 People with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge who are not able to use the hob
safely on their own must be supervised whilst using it. They may
only use it unsupervised if they have been shown how to use it safely
and recognise and understand the consequences of incorrect
operation.
7
Warning and Safety instructions
Safety with children
 Children under 8 years of age must be kept away from the hob
unless they are constantly supervised.
 Children 8 years and older may only use the hob unsupervised if
they have been shown how to use it in a safe way and can recognise
and understand the consequences of incorrect operation.
 Children must not be allowed to clean the hob unsupervised.
 Please supervise children in the vicinity of the hob and do not let
them play with it.
 The hob gets hot when in use and remains hot for a while after
being switched off. Keep children well away from the hob until it has
cooled down and there is no danger of burning.
 Danger of burning.
Do not store anything which might arouse a child's interest in
storage areas above or next to the hob. Otherwise they could be
tempted into climbing onto the appliance.
 Danger of burning or scalding.
Place pots and pans on the cooking zone in such a way that children
cannot pull them down and burn themselves.
 Danger of suffocation. Packaging, e.g. plastic wrappings, must be
kept out of the reach of babies and children. Whilst playing, children
could become entangled in packaging or pull it over their head and
suffocate.
8
Warning and Safety instructions
Technical safety
 Unauthorised installation, maintenance and repairs can cause
considerable danger for the user. Installation, maintenance and
repairs must only be carried out by a Miele authorised technician.
 Do not use a damaged appliance. It could be dangerous. Check
the hob for visible signs of damage.
 Reliable and safe operation of this hob can only be assured if it
has been connected to the mains electricity supply.
 The electrical safety of this hob can only be guaranteed when
correctly earthed. It is essential that this standard safety requirement
is met. If in any doubt please have the electrical installation tested by
a registered electrical worker.
 To avoid the risk of damage to the hob, make sure that the
connection data on the data plate (voltage and frequency) match the
mains electricity supply before connecting it to the mains.
Consult a registered electrical worker if in doubt.
 Do not connect the hob to the mains electrical supply by a multisocket adapter or extension lead. These are a fire hazard and do not
guarantee the required safety of the appliance.
 For safety reasons, this hob may only be used after it has been
built in.
 This hob must not be used in a non-stationary location (e.g. on a
ship).
 Never open the casing of the hob.
Touching or tampering with electrical connections or components
and mechanical parts is highly dangerous to the user and can cause
operational faults.
 While the hob is under warranty, repairs should only be
undertaken by a Miele authorised service technician. Otherwise the
warranty is invalidated.
9
Warning and Safety instructions
 Miele can only guarantee the safety of the appliance when
genuine original Miele replacement parts are used. Faulty
components must only be replaced by Miele spare parts.
 The hob is not intended for use with an external timer switch or a
remote control system.
 Connection to the gas supply must be carried out by a registered
gas installer. The hob may be connected to the electrical supply by a
fused plug and switched socket. If you wish to connect it to a fused
spur connection, or if the plug has been removed or the connection
cable is not supplied with a plug, the hob must be connected to the
mains supply by a registered electrical worker.
 During installation, maintenance and repair work, the hob must be
disconnected from the mains electricity supply. The gas supply must
also be shut off. Depending on territory this is done in one of several
different ways:
– the mains fuse has been removed, or
– the screw-out fuse is removed (if applicable), or
– switch off at the wall socket and withdraw the plug from the
socket. Pull by the plug and not by the mains connection cable to
disconnect from the mains electricity supply.
– the gas inlet valve is closed.
 Danger of electric shock!
Do not use the hob if it is faulty. Shut off the gas supply and contact
Miele.
 If the appliance is installed behind a furniture door, do not close
the door while the appliance is in operation. Heat and moisture
would build up behind a closed furniture door, potentially causing
damage to the appliance, the furniture unit and the flooring. Wait
until the appliance has cooled down completely before closing the
furniture door.
10
Warning and Safety instructions
Correct use
 The appliance gets hot when in use and remains hot for some
time after being switched off. Do not touch the appliance if there is a
possibility that it could still be hot.
 Due to the high temperatures radiated, objects left near the hob
when it is in use could catch fire.
Do not use the hob to heat up the room.
 Oil and fat can overheat and catch fire. Do not leave the hob
unattended when cooking with oil and fat. If it does ignite do not
attempt to put the flames out with water.
Disconnect the hob from the mains and use a suitable fire blanket,
saucepan lid, damp towel or similar to smother the flames.
 Flames could set the grease filters of a cooker hood on fire. Do
not flambé under a cooker hood.
 Spray canisters, aerosols and other inflammable substances can
ignite when heated. Therefore do not store such items or substances
in a drawer under the hob. Cutlery inserts must be heat-resistant.
 Do not heat an empty pan.
 Do not heat up food in closed containers e.g. tins or sealed jars
on the hob, as pressure can build up in the container, causing it to
explode.
 Do not cover the hob, e.g. with a hob cover, a cloth or protective
foil. The material could catch fire, shatter or melt if the hob is
switched on by mistake or if residual heat is still present.
 When the hob is switched on either deliberately or by mistake, or
when there is residual heat present, there is the risk of any metal
items left on the hob heating up, with the danger of burning.
Depending on the material, other items left on the appliance could
also melt or catch fire. Do not use the hob as a resting place.
11
Warning and Safety instructions
 You could burn yourself on the hot hob. Protect your hands with
heat-resistant pot holders or gloves when handling hot pots and
pans. Do not let them get wet or damp, as this causes heat to
transfer through the material more quickly with the risk of scalding or
burning yourself on steam. Be sure to keep all textiles away from the
gas flames. Do not use oversized cloths, tea towels or other similar
materials.
 When using an electrical appliance, e.g. a hand-held food blender,
near the hob, ensure that the cable of the electrical appliance cannot
come into contact with the hot hob. The insulation on the cable
could become damaged.
 Plastic and aluminium foil containers melt at high temperatures.
Do not use plastic or aluminium foil containers on the hob.
 If a cooker hood is installed above the hob, ensure that the
burners are always covered with a pan when in use. Otherwise
flames could reach the cooker hood, parts of which could then be
damaged or even set on fire.
 Only light the gas burners after all burner parts have been properly
assembled.
 Pans must be the correct size for the burner they are used on (see
"Pans"). A pan which is too small will be unstable on the pan
support. If the pan diameter is too large, flames can spread out to
the sides and damage or burn the worktop, wall claddings or
surrounding units and also parts of the cooktop. Miele cannot be
held liable for this type of damage.
 Ensure that the flames from the burner do not spread out beyond
the base and up the sides of the pan.
 Do not use pans with very thin bases on this hob, and never heat
up empty pans as they could get damaged. This could also damage
the appliance.
12
Warning and Safety instructions
 The pan support supplied with the appliance must always be
used. Never place a pan on the burner itself.
 Replace the pan supports carefully to avoid scratching the surface
of the hob.
 Do not use or store flammable materials near this hob.
 Remove splashes of fat and other food debris from the surface of
the hob as soon as possible. These are a fire hazard.
 Avoid allowing liquids or foods containing salt to spill onto the
hob. If salty foods or liquids do get on the hob, they should be
removed as soon as possible to avoid the risk of corrosion.
 The use of the hob creates heat, moisture and combustion
products in the room where it is installed. Make sure that the
appliance is installed in a location with sufficient ventilation. Natural
ventilation openings should not be blocked. Alternatively, a
mechanical ventilation device (e.g. a cooker hood) can be installed.
 Prolonged intensive use of the hob may require additional
ventilation of the room, e.g., by opening a window, or by operating
the cooker hood on a higher setting.
 Do not use roasting dishes, pans or grilling stones that are large
enough to cover more than one burner. The resulting build-up of
heat could damage the hob.
 If the hob has not been used for a longer period of time, it should
be thoroughly cleaned before it is used again. It is also advisable to
have it tested by registered gas installer for safety. This should be
done at regular intervals.
 Where several CombiSets are installed side by side:
Hot objects can damage the seal of the cover strip between the
appliances. Do not place hot pans near or on the cover strip.
13
Warning and Safety instructions
Cleaning and care
 Do not use a steam cleaning appliance to clean this hob.
The steam could reach electrical components and cause a short
circuit.
14
Caring for the environment
Disposal of the packing
material
Disposing of your old
appliance
The packaging is designed to protect
the appliance from damage during
transportation. The packaging materials
used are selected from materials which
are environmentally friendly for disposal
and should be recycled.
Electrical and electronic appliances
often contain valuable materials. They
also contain specific materials,
compounds and components, which
were essential for their correct function
and safety. These could be hazardous
to human health and to the environment
if disposed of with your domestic waste
or if handled incorrectly. Please do not,
therefore, dispose of your old appliance
with your household waste.
Recycling the packaging reduces the
use of raw materials in the
manufacturing process and also
reduces the amount of waste in landfill
sites.
Please dispose of it at your local
community waste collection / recycling
centre for electrical and electronic
appliances, or contact your dealer or
Miele for advice. You are also
responsible (by law, depending on
territory) for deleting any personal data
that may be stored on the appliance
being disposed of. Please ensure that
your old appliance poses no risk to
children while being stored prior to
disposal.
15
Guide to the appliance
Hob
a Large burner
Control knobs for the cooking zones
b Normal burner
e Rear
c Pot rests
f Front
d Symbols to indicate which gas
burner the control is for
16
Guide to the appliance
Control knob
Symbol
Description

Burner off, the gas supply is turned off

Largest flame

Smallest flame
17
Guide to the appliance
Burner
n Burner cap
o Burner head
p Ignition safety device
q Ignitor
r Burner base
18
Before using for the first time
 Please stick the extra data plate for
the appliance supplied with this
documentation in the space provided
in the "After sales service" section of
this booklet.
 Remove any protective wrapping and
stickers.
Cleaning the hob for the first
time
Switching on the hob for the
first time
The metal components have a
protective coating which when heated
for the first time will give off a slight
smell and possibly some vapours.
The smell and any vapours given off do
not indicate a faulty connection or
appliance and they are not hazardous
to health.
 Clean all removable parts of the
burners with a solution of warm water
and a small amount of washing-up
liquid applied with a soft sponge. Dry
all parts thoroughly after cleaning and
then reassemble the burners (see
"Cleaning and care").
 Clean the stainless steel trough with a
damp cloth, and then wipe dry.
19
Pans
Ø Pan [cm]
Burner
Minimum base
diameter
Normal burner
12
Large burner
14
Burner
Maximum rim
diameter
Normal burner
22
Large burner
24
– Select cookware that fits the size of
the burner:
Large diameter = large burner
Small diameter = small burner.
– Refer to the chart above and ensure
that the pan diameter falls within the
minimum and maximum diameters
given for the burner you are using. If
the pan diameter is too large, flames
can spread out to the sides and
damage or burn the worktop, wall
claddings or surrounding units and
also parts of the hob or other
appliances.
Pans which are too small for the pan
supports, or pans which do not sit
securely on the pan supports, are
dangerous and should not be used.
– Unlike pans that are used on an
electric hob, the bottom of pans used
on a gas hob do not have to be flat to
deliver good cooking results.
– Remember when purchasing new
pans that manufacturers usually refer
to the diameter at the top of the pan
in their documentation, and not to the
base diameter.
20
– Any heat-resistant pans can be used
on a gas burner.
– Pans with thick bases are preferable
as these distribute heat more evenly.
With thin bases, there is a danger of
food overheating in places. Stir the
food frequently.
– Always place cookware on the pan
support supplied with the appliance.
Never place it directly on the burner.
– Position the cookware centrally on
the pan support so that it sits
securely and cannot tip. A little
movement is quite normal and not a
cause for concern.
– Do not use pots or pans that have
bases with pronounced edges.
Tips on saving energy
– Use a pan lid whenever possible to
minimize heat loss.
– Wide, shallow pans are preferable to
tall, narrow ones. They will heat up
faster.
– Cook with as little water as possible.
– Reduce the size of the flame once the
water has come to the boil or the oil
is hot enough to fry in.
– Use a pressure cooker to reduce
cooking times.
21
Operation
 Fire hazard.
Adjusting the flame
Do not leave the appliance
unattended whilst it is being used.
The burners can be regulated at any
level between the strongest and
weakest flame.
Switching on
 The control for the burner must be
pressed in and turned anti-clockwise
to the large flame symbol to switch
on. The ignitor will "click" and ignite
the gas.
When a control knob is activated, a
spark is developed automatically at all
rings. This is normal and does not
indicate a defect.
As the outer part of the flame is much
hotter than the centre, the tips of the
flames should stay beneath the pan
base. Flame tips which extend beyond
the sides of the pan merely warm up
the air in the room and can also
damage pan handles and increase the
danger of injury.
 When a flame is visible, keep the
control knob pressed in for
5-10 seconds, and then let it go.
 If the burner does not ignite, turn the
control knob back to "". Air the room
or wait at least one minute before
trying again. Try keeping the control
knob pressed in for a little longer the
next time.
 If the burner does not ignite the
second time, turn the control knob
back to "" and see "Problem solving
guide".
22
 Adjust the flame so that it does not
spread out beyond the sides of the
pan.
Switching off
 Turn the control clockwise to position
"".
This stops the flow of gas and the flame
goes out.
Safety features
Thermo-electric flame failure
monitor
This hob has a thermo-electric flame
failure monitor. If the flame goes out, for
example because food has boiled over
or if there has been a sudden draught,
the supply of gas to the burner will be
cut off. This will prevent any gas
escaping. To use the burner again, turn
the control knob to "".
The thermo-electric flame failure
monitor operates independently from
the electricity supply. This means that
it will still work if the hob is used
during a power cut.
23
Cleaning and care
 Danger of burning.
The burners must be switched off.
The hob needs to cool down.
 Danger of injury.
The steam from a steam cleaning
appliance could reach electrical
components and cause a short
circuit.
Do not use a steam cleaner to clean
the hob.
The use of unsuitable cleaning
agents can cause the surfaces to
discolour or alter.
All surfaces are susceptible to
scratching.
Remove any residual cleaning agent
immediately.
Allow the CombiSet to cool down
before cleaning.
 The CombiSet and accessories
should be cleaned after each use.
 Dry the CombiSet after using water to
clean it. This helps prevent limescale
deposits.
Unsuitable cleaning agents
To avoid damaging the surfaces, do not
use:
– cleaning agents containing soda,
alkalines, ammonia, acids or
chlorides
– cleaning agents containing descaling
agents
– stain or rust removers
– abrasive cleaning agents, e.g.
powder cleaners and cream cleaners
– solvent-based cleaning agents
– dishwasher cleaner
– grill and oven cleaners
– glass cleaning agents
– hard, abrasive brushes or sponges,
e.g. pot scourers, brushes or
sponges which have been previously
used with abrasive cleaning agents
– melamine eraser blocks
24
Cleaning and care
Stainless steel frame/control
panel
 Clean the frame and the control panel
with a solution of warm water and a
little washing-up liquid applied with a
soft sponge.
You can also use a ceramic and
stainless steel cleaning agent. We
recommend also using a stainless steel
conditioning agent to help prevent
resoiling (see "Optional accessories).
Do not use ceramic and stainless
steel cleaner or stainless steel
conditioning agent on the printing.
This would rub the printing off.
These areas should be only cleaned
with a solution of warm water and a
little washing-up liquid applied with a
soft sponge.
Control knobs
 Clean the control(s) with a solution of
warm water and a little washing-up
liquid applied with a soft sponge.
Stubborn soiling should be soaked
first.
 Dry the control(s) with a clean cloth.
Stainless steel trough
Do not clean the area between the
hob and the worktop with sharp,
pointed objects.
This could damage the seals.
Soiling, particularly salty food or
liquid and olive oil, can cause
damage if left on the printed surfaces
for a long time.
Remove any soiling which comes
into contact with the printed symbols
straight away.
Stainless steel cleaning agents rub
off the printed symbols.
Do not use stainless steel cleaning
agents on printed symbols.
 Clean stainless steel surfaces with a
solution of warm water and a small
amount of washing-up liquid applied
with a soft sponge. In the case of
stubborn dried-on soiling, soak first.
If necessary, the rough side of nonscouring sponge can be used.
 Finally, dry with a clean soft cloth.
Tip: The Miele conditioning agent for
stainless steel can be used after
cleaning to help keep your appliance
looking good (see "Optional
accessories"). Apply sparingly with a
soft cloth following the instructions on
the packaging.
25
Cleaning and care
Pan supports
Do not clean the pan supports in a
dishwasher.
 Remove the pan supports.
 Clean the pan supports with a
solution of warm water and a little
washing-up liquid applied with a soft
sponge. Stubborn soiling should be
soaked first.
 After cleaning, dry the pan supports
thoroughly with a clean cloth.
Burner
Do not clean any parts of the burner
in a dishwasher.
 The burner should be dismantled and
then cleaned by hand using a
solution of warm water and a little
washing-up liquid applied with a soft
sponge.
 Parts of the burner that cannot be
removed should be wiped clean with
a damp cloth only.
 The ignitor and thermocouple should
be very carefully wiped clean using a
well wrung out cloth.
Do not let the ignitor get wet. If it gets
wet, it will not spark.
 After cleaning, dry all surfaces with a
clean cloth. Make sure that the flame
slits are clean and completely dry.
The surfaces of the burner caps will
become more matt with time. This is
quite normal and does not indicate
damage to the burner caps. Nor will
affect the operation of the hob.
26
Cleaning and care
Assembling the burner
 Place the burner head  on the
burner base  so that the ignition
safety device  and the ignitor 
extend through their respective holes
in the burner head.
The burner head must click into place
correctly.
 Place the burner cap  flat over the
burner head . When correctly
positioned, it will not slide about.
Ensure parts are reassembled in the
correct order.
27
Problem solving guide
Many malfunctions and faults that can occur in daily operation can be easily
remedied. Time and money will be saved because a service call will not be
needed.
The following guide may help you to find the reason for a malfunction or a fault,
and to correct it.
Problem
Cause and remedy
The burners do not
There could be an air lock in the gas pipe.
ignite when the hob is
 You may need to make several attempts before the
being used for the first
burner ignites successfully.
time or after it has been
out of use for a longer
period.
The burner does not
ignite after several
attempts.
There may be a technical fault.
 Turn all of the controls clockwise to "" and
interrupt the power supply to the hob for a few
seconds.
The burner is not correctly assembled.
 Assemble the burner correctly.
The gas shut-off valve is closed.
 Open the gas shut-off valve.
The burner is wet and/or dirty.
 Clean and dry the burner.
The flame slits are blocked and/or wet.
 Clean and dry the flame slits.
The gas flame goes out
after being lit.
The flames do not touch the thermocouple and the
burner does not get hot enough:
The burner parts are not positioned correctly.
 Position the burner parts correctly.
There is soiling on the thermocouple.
 Remove any soiling.
The flame suddenly
looks different.
The burner parts are not positioned correctly.
 Position the burner parts correctly.
The burner head or the holes in the burner cap are
dirty.
 Remove any soiling.
The gas flame goes out
during use.
28
The burner parts are not positioned correctly.
 Position the burner parts correctly.
Problem solving guide
Problem
Cause and remedy
The ignitor on the
burner does not spark.
The mains fuse has tripped.
 You may need to contact a registered electrical
worker or Miele.
There is food residue stuck between the ignitor and
the burner cap.
There is food residue on the thermocouple.
 Remove any soiling (See "Cleaning and care").
29
Optional accessories
Miele offer a comprehensive range of
useful accessories as well as cleaning
and conditioning products for your
Miele appliances.
These products can be ordered through
the Miele Webshop.
Stainless steel conditioning
agent 250 ml
Removes water marks, flecks and finger
prints. Helps keep the appliance looking
good for longer.
These can also be ordered from Miele
(see end of this booklet for contact
details) or from your Miele dealer.
Ceramic and stainless steel
hob cleaner 250 ml
Microfibre cloth
Removes heavy soiling, limescale
deposits and aluminium residues
Removes finger marks and light soiling
30
Safety instructions for installation
Fit the wall units and cooker hood before fitting the CombiSet to avoid
damaging it.
 The veneer or laminate coatings of worktops (or adjacent kitchen
units) must be treated with 100 °C heat-resistant adhesive which will
not dissolve or distort. Any backmoulds must be of heat-resistant
material.
 A deep fat fryer must not be installed directly next to a gas hob or
a wok burner as the gas flames could ignite the fat in the fryer. It is
essential to maintain a distance of at least 288 mm between these
two appliances.
 The CombiSet must not be installed over a fridge, fridge-freezer,
freezer, dishwasher, washing machine, washer-dryer or tumble dryer.
 When installing the CombiSet, make sure that the gas hose and
the electrical connection cable cannot come into contact with hot
appliance parts.
 The electrical cable and any flexible gas connection pipes must be
installed in such a way so that they do not come into contact with
any moving kitchen parts (e.g. a drawer), and cannot become
trapped.
 Observe carefully the safety clearances listed on the following
pages.
All dimensions are given in mm.
31
Safety distances
Safety distance above the
CombiSet
Safety Distance below the
CombiSet
There should be at least 30 mm height
or plenty of space reserved below the
CombiSet for the installation of the
flexible gas connection pipe and
electrical cable. It also avoids any
possible hindrance towards the
movement of all moveable kitchen parts
(e.g. drawer).
A minimum safety distance must be
maintained between the CombiSet and
the cooker hood above it. See the
cooker hood manufacturer's operating
and installation instructions for details.
If the manufacturer's instructions are
not available for the cooker hood a
minimum safety distance of at least
760 mm must be maintained, or if any
flammable objects (e.g. utensil rails,
wall units etc) are installed above the
CombiSet, a minimum safety distance
of at least 760 mm must be maintained
between them and the CombiSet
below.
When two or more CombiSets which
have different safety distances are
installed together below a cooker
hood, you should observe the
greatest safety distance.
32
Safety distances
Safety distances to the sides
and back of the hob
The CombiSet may be installed with a
wall at the rear and a tall unit or wall to
one side (right or left) (see illustrations).
 Minimum distance between the back
of the worktop cut-out and the rear
edge of the worktop:
50 mm
Not allowed
 Minimum distance between the
worktop cut-out and a tall unit or wall to
the right or left of it:
40 mm
CS 1212 / CS 1212-1
CS 1221 / CS 1221-1
CS 1234 / CS 1234-1
CS 1223
CS 1222
50 mm
CS 1112
CS 1122
CS 1134
CS 1326
CS 1327
CS 1411
100 mm
CS 1012 / CS 1012-1
CS 1013 / CS 1013-1
150 mm
CS 1421
CS 1312
CS 1322
200 mm
CS 1034 / CS 1034-1
250 mm
CS 1011 / CS 1021
CS 1018 / CS 1018 G
CS 1028 G
Recommended
Not recommended
Not recommended
33
Safety distances
Safety distance when installing the appliance near a wall with
additional niche cladding
A minimum safety distance must be maintained between the worktop cut-out and
any niche cladding to protect it from heat damage.
If the niche cladding is made from a combustible material (e.g. wood) a minimum
safety distance  of 50 mm must be maintained between the cut-out and the
cladding.
If the niche cladding is made from a non-combustible material (e.g. metal, natural
stone, ceramic tiles) the minimum safety distance  between the cut-out and the
cladding will be 50 mm less the thickness of the cladding.
Example: 15 mm niche cladding
50 mm - 15 mm = minimum safety distance of 35 mm
a Masonry
b Niche cladding dimension x = thickness of the niche cladding material
c Worktop
d Worktop cut-out
e Minimum distance to
combustible materials 50 mm
non-combustible materials 50 mm - dimension x
34
Installation notes
Seal between the CombiSet
and the worktop
Do not use sealant between the
CombiSet and the worktop. This
could result in damage to the
CombiSet or the worktop if the
CombiSet ever needs to be removed
for servicing.
The sealing strip under the edge of
the top part of the appliance
provides a sufficient seal for the
worktop.
Tiled worktop
Grout lines  and the hatched area
underneath the CombiSet frame must
be smooth and even. If they are not the
CombiSet will not sit flush with the
worktop and the sealing strip
underneath the top part of the
appliance will not provide a good seal
between the appliance and the
worktop.
35
Building-in dimensions
a Spring clamps
b Front
c Building-in depth
d Mains connection box with mains connection cable,
L = 1440 mm
e Gas connection R 1/2
36
Building-in several CombiSets
Example: 3 CombiSets
a Spring clamps
b Spacer bars
c Gaps between spacer bars and worktop
d Cover strips
e CombiSet width minus 8 mm
f CombiSet width
g CombiSet width minus 8 mm
h Worktop cut-out
37
Building-in several CombiSets
Calculating the worktop cut-out
The frames of the CombiSets overlap the worktop at the outside right and left by
8 mm on each side.
 Add up the widths of the CombiSets and subtract 16 mm from this figure.
Example:
288 mm + 288 mm + 380 mm = 956 mm - 16 mm = 940 mm
The CombiSets are 288 mm, 380 mm or 576 mm wide depending on model (see
"Building-in dimensions").
Spacer bars
When building-in several CombiSets a spacer bar must be fitted between each
CombiSet. The position for securing the spacer bar will depend on the width of the
CombiSet.
38
Installation
Preparing the worktop
 Make the worktop cut-out as shown
in "Building-in dimensions" or as
calculated (see Building-in several
CombiSets). Observe the safety
distances (see "Safety distances").
Wooden worktops
 Seal the cut surfaces with a suitable
sealant to avoid swelling caused by
moisture. The sealant must be heatresistant.
Make sure that the sealant does not
come into contact with the top of the
worktop.
 Position the spring clamps  and
spacer bars  on or at the top edge
of the cut-out in the positions shown.
 Secure the spring clamps  and
spacer bars  with the 3.5 x 25 mm
wood screws supplied.
39
Installation
Natural stone worktops
You will need heavy duty double-side
tape (not supplied) to secure the
spring clamps and spacer bars.
 Apply silicone to the side and lower
edges of the spring clamps  and
the spacer bars .
 Stick the tape  to the top edge of
the cut-out in the positions shown in
the diagram.
 Position the spring clamps  and
spacer bars  on or at the top edge
of the cut-out and press them firmly
into place.
40
 Then fill gap  between spacer
bar  and the worktop with silicone.
Installation
Installing the CombiSet
Building in several CombiSets
 Feed the mains connection cable
down through the cut-out.
 Push the built-in CombiSet to the
side until the holes in the spacer bar
can be seen.
 Starting at the front, position the
CombiSet in the worktop cut-out.
 Using both hands, press down evenly
on the edges of the CombiSet until it
clicks into position. When doing this
make sure that the seal underneath
the appliance sits flush with the
worktop. This is important to ensure
an effective seal with the worktop.
Do not use sealant (e.g. silicone).
If the seal does not meet the worktop
correctly on the corners, the corner
radius (≤ R4) can be carefully sculped
to suit.
 Fit cover strip  into the holes in
spacer bar .
 Starting at the front, position the next
CombiSet in the worktop cut-out.
 Proceed as described previously.
41
Installation
Connecting the CombiSet
Removing the CombiSet
 Connect the CombiSet to the
electricity and gas supplies (see "Gas
connection").
 If the CombiSet can be accessed
from below, push it out from below.
Push the rear side out first.
Checking operation
 If the CombiSet is not accessible
from below, take hold of the
appliance with both hands at the
back, pull it forwards, then lift it up
and out.
 After installation, ignite all burners to
check that they are operating
correctly:
– The flame must not go out on the
lowest setting, or when the control is
turned quickly from the highest to the
lowest setting.
– On the highest setting, the flame
must have a distinctive and visible
core.
42
Electrical connection
All electrical work should be carried out
by a registered electrical worker in strict
accordance with current local safety
regulations. Connection should be
made via a switched socket. This will
make it easier for service technicians
should the appliance need to be
repaired. The electrical socket must be
easily accessible after installation.
 Danger of injury.
Miele cannot be held liable for
unauthorised installation,
maintenance and repair work as this
can be dangerous to users.
Miele cannot be held liable for
damage or injury caused by incorrect
installation, maintenance or repair
work, or by an inadequate or faulty
earthing system (e.g. electric shock).
If the plug is removed from the
connection cable or if the cable is
supplied without a plug, the
appliance must be connected to the
electrical supply by a registered
electrical worker.
If the switched socket is not
accessible after installation, or if the
appliance is to be hard-wired, an
additional means of disconnection
must be provided for all poles.
Connection data is shown on the
data plate. It must match the mains
electrical supply.
After installation ensure that all
electrical components are shielded
and cannot be accessed by users.
Total power rating
See data plate
Connection
AC 220 V, 50 Hz
The connection data is quoted on the
dataplate. It must match the household
supply.
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Blue = neutral
Brown = live
WARNING
THIS APPLIANCE MUST BE
EARTHED
Residual current device
For extra safety, it is advisable to
protect the CombiSet with a suitable
residual current device (RCD) with a trip
range of 30 mA.
43
Electrical connection
Disconnecting from the mains
Replacing the mains cable
 Danger of electric shock.
 Danger of electric shock.
After disconnection, ensure the
appliance cannot be switched back
on by mistake.
The mains connection cable must be
replaced by a registered electrical
worker in accordance with current
local safety regulations.
To disconnect the appliance from the
mains power supply, do one of the
following depending on installation:
Safety fuses
 Completely remove fuses
Automatic circuit breakers
 Press the (red) button until the middle
(black) button springs out.
Built-in circuit breakers
 Circuit breakers, type B or C: switch
the on-off switch from 1 (on) to 0 (off).
Residual current device (RCD)
 Switch the main switch from 1 (on) to
0 (off) or press the test button.
44
If the mains cable needs to be replaced
it must be replaced with a special
connection cable, type H 05 VV-F (PVCinsulated), available from Miele.
The connection data is quoted on the
data plate.
Gas connection
 According to the Gas Safety
(Registration of Gas Installers and
Gas Contractors) Regulations, any
gas installation work including the
installation of appliances and
connecting tubing, must be
undertaken by a registered gas
installer who is registered for that
appropriate class and is employed
by a registered gas contractor. The
installer is responsible for ensuring
that the appliance functions correctly
when installed.
Use approved gas tubing bearing
EMSD approval marking (such as:
EMSD APPROVAL GTXXXX) for
connection to appliances, or other
appropriate methods accepted by
EMSD.
The gas connection must be
installed so that connection can be
made either from inside or outside
the kitchen unit. The isolating valve
must be easily accessible and visible
(by opening the kitchen door if
necessary).
Check with your local gas supplier
about the type of gas its calorific
value and compare this information
with the type of gas quoted on the
appliance's data plate.
Connection to the gas supply must
be carried out in strict accordance
with current local regulations. Every
appliance should have its own easily
accessible isolating valve and test
point.
Any special local conditions relating
to gas installations as well as
building regulations must also be
observed.
Gas connections, pipes and
connection cables can suffer
damage if exposed to heat from the
hob.
After installation make sure that
neither the gas pipe nor the mains
cable can come into contact with hot
parts of the appliance and that the
gas pipe and connections on the hob
cannot come into contact with hot
gas exhaust.
Flexible gas pipes can be damaged
by incorrect routing.
Attach flexible gas pipes in such a
way so that they do not come into
contact with any moving kitchen
parts (e.g. a drawer) and are not
exposed to mechanical stress.
The hob must be set for local gas
conditions and the gas connection
must undergo a leakage test.
This hob is not connected to an
exhaust flue.
When installing and connecting the
appliance please observe all relevant
installation instructions and ensure it
has adequate ventilation once
installed.
45
Gas connection
This appliance is set up for connection
to liquefied petroleum gas (LPG) or
town gas (TG) (see label on the
appliance).
Appliances set up for connection to
town gas have the gas governor MDG
ELITRE (model-no. EL-125, pressure
setting at 10 mbar) included.
Connecting the hob
The hob is supplied with a conical ½"
gas connection point for connection to
one of the following:
– Rigid connection with isolation valve
– Flexible connection, maximum length
2000 mm.
Unsuitable sealants may not be leakproof.
Connections must be sealed using
appropriate sealant.
Use approved gas tubing bearing
EMSD approval marking (such as:
EMSD APPROVAL GTXXXX) for
connection to appliances, or other
appropriate methods accepted by
EMSD.
46
c Gas connection R ½"
d 90° bend
 According to the Gas Safety
(Registration of Gas Installers and
Gas Contractors) Regulations, any
gas installation work including the
installation of appliances and
connecting tubing, must be
undertaken by a registered gas
installer who is registered for that
appropriate class and is employed
by a registered gas contractor.
Burner ratings
Nominal ratings
Burner
Gas type
Highest setting
Lowest setting
kW
g/h
kW
Normal burner Liquefied Petroleum
gas (29 mbar)
1.8
131
0.35
Town gas (10 mbar)
1.8
–
0.35
Liquefied Petroleum
gas (29 mbar)
3.0
218
0.5
Town gas (10 mbar)
3.0
–
0.5
Liquefied Petroleum
gas (29 mbar)
4.8
349
–
Town gas (10 mbar)
4.8
–
–
Large burner
Total
47
After sales service
Contact in case of malfunction
In the event of any faults which you cannot remedy yourself, please contact your
Miele Dealer or Miele Service.
Contact information for Miele Service can be found at the end of this document.
Please note that telephone calls may be monitored and recorded for training
purposes and that a call-out charge will be applied to service visits where the
problem could have been resolved as described in this booklet.
Please quote the model and serial number of your appliance when contacting
Miele. This information can be found on the data plate.
Data plate
Stick the extra data plate supplied with the appliance here. Make sure that the
model number matches the one specified on the back cover of this document.
Guarantee
For information on the appliance guarantee specific to your country please contact
Miele. See end of this booklet for contact details.
48
Technical Data
Model No
CS 1013-1
Cut-out dimensions
Width
272 mm
Depth
500 mm
Build-in depth
(Allow additional space below for
connection to the gas supply)
87 mm
Unit Dimensions
Width
288 mm
Depth
520 mm
Electrical connection
Voltage
220–240 V
Fuse rating
13 A
Gas Type
Town Gas
(with external gas
governor)
Liquefied Petroleum Gas
10 mbar / 1 kPa
29 mbar / 2.9 kPa
Front burner
1.8 kW
1.8 kW
Rear burner
3.0 kW
3.0 kW
Connection Pressure
Heat input
49
Miele (Hong Kong) Limited
41/F - 4101, Manhattan Place
23 Wang Tai Road
Kowloon Bay
Hong Kong
Tel: (852) 2610 1025
Fax: (852) 3579 1404
E-mail: customerservices@miele.com.hk
Website: www.miele.hk
Miele (Hong Kong) Limited
香港九龍灣宏泰道23號
Manhattan Place 41樓4101室
電話: (852) 2610 1025
傳真: (852) 3579 1404
電郵地址: customerservices@miele.com.hk
網址: www.miele.hk
Miele Boutique
Ground Floor
111 Leighton Road
Causeway Bay
Hong Kong
Tel: (852) 2890 1018
Fax: (852) 2890 1199
E-mail: showroom@miele.com.hk
M
陳列室
Miele
香港銅鑼灣禮頓道111號地下
電話: (852) 2890 1018
傳真: (852) 2890 1199
電郵地址: showroom@miele.com.hk
International Head Office
Miele & Cie. KG
Carl-Miele-Straße 29
33332 Gütersloh
Germany
CS 1013-1

en-HK
M.-Nr. 10 829 880 / 00
Download PDF

advertising