K5 Beam - user manual

Guangzhou Liangyi Lighting Equipments Co.,Ltd.
37 Gongyedadao, Xinhua, Huadu, Guangzhou PC:510800
Tel: (020)666 090 88-8002 Fax: (020) 868 670 11
www. eklights.com
USER MANUAL
www.eklights.com
CONTENTS
SAFETY
01
DIMENSION
02
DESCRIPTION
02
INTRODUCTION
03
INSTALLATION
04
DMX CONNECTION
04
POWER CONNECTION
05
TECHNICAL SPECIFICATION
06
COLOR
07
PHOTOMETRICS
07
MENU
08
MENU DESCRIPTION
09
DMX CHANNEL
11
MASTER/SLAVE OPERATION
14
UFI OPERATION
15
TROUBLE SHOOTING
16
www.eklights.com
TROUBLE SHOOTING
Problem
Fixture does not light up
General low light intensity
Before carrying out any operations with the unit, carefully read this instruction
manual and keep it with cure for future reference. It contains important information
WARNING about the installation, usage and maintenance of the unit.
Checklist and Remedies
Possible Causes
• No mains supply
• Dimmer fader set to 0
• All color faders set to 0
• Faulty LED
• Faulty LED board
• Check the power supply voltage
• Increase the value of the dimmer channels
• Increase the value of the color channels
• Replace the LED board
• Replace the LED board
• Dirty lens assembly
• Misaligned lens assembly
• Clean the fixture regularly
• Install lens assembly properly
• No power
• Check for power on power outlet
• Faulty internal power supply
• Replace internal power supply
• Wrong DMX addressing
• Check control panel and unit addressing
• Check DMX cables
• Install terminator as suggested
Fixture does not power up • Loose or damaged power cord • Check power cord
Fixture does not respond to DMX • Damaged DMX cables
• Bouncing signals
SAFETY
General instruction
● The products referred to in this manual conform to the European Community Directives and are therefore marked with.
● The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.
● Never make any modifications on the unit not described in this instruction manual, otherwise you will
risk an electric shock.
● Connection must be made to a power supply system fitted with efficient earthing (Class I appliance according to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units
from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
● The connection to the main network of electric distribution must be carried out by a qualified electrical
installer. Check that the main frequency and voltage correspond to those for which the unit is designed
as given on the electrical data label.
● This unit is not for home use, only professional applications.
● Never use the fixture under the following conditions:
-in places wet;
-in places subject to vibrations or bumps;
-in places with an ambient temperature of over 45°
● Make certain that no inflammable liquids, water or metal objects enter the fixture.
● All work must always be carried out by qualified technical personnel. Contact the nearest sales point
for an inspection or contact the manufacturer directly.
● If the unit is to be put out of operation definitively, take it to a local recycling plant for a disposal
Warnings and installation precautions
● If this device will be operated in any way different to the one described in this manual, it may suffer
damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like
short circuit, burns, electric shock, etc.
● Before starting any maintenance work or cleaning the projector, cut off power from the main suply.
● Always additionally secure the projector with the safety rope. When carrying out any work, always comply
scrupulously with all the regulations (particularly regarding safety) currently in force in the country
in which the fixture’s being used.
● For inside use only. Not designed for outside use.
● The minimum distance between the fixture and surrounding walls must be more than 50cm and the
air vents at the housing must not be covered in any case.
● Install the fixture in a well ventilated place.
● Keep any inflammable material at a safe distance from the fixture.
● The maximum temperature that can be reached on the external surface of the fitting, in a thermally
steady state, is high. After power off, please cool down over 15 minutes.
● Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent
that their effectiveness is impaired.
● The lamp(LED) shall be changed if it has become damaged or thermally deformed.
● Never look directly at the light beam. Please note that fast changes in lighting, e.g. flashing light,
may trigger epileptic seizures in photosensitive persons or persons with epilepsy.
03
16
01
www.eklights.com
DIMENSION
UFI OPERATION
DMX SETTING
1 2 3 4 5
TRANSISTING
310
5
348
278
193
?8
174
74
228
200
ON
OFF
ON
OFF
RECEIVING
ON
OFF
Channel 1
Channel 1
Channel 2
Channel 3
Channel 3
Channel 4
Channel 4
Channel 5
Channel 5
Channel 6
Channel 6
Channel 7
Channel 7
Channel 8
Channel 8
Channel 9
Channel 9
Tight, solid, consistent beams
Channel 10
Channel 10
Extensive rotating gobo pattern selection
Channel 11
Channel 11
Featuring color wheel, rotating gobos, prism
Channel 12
Channel 12
Channel 13
Channel 13
Channel 14
Channel 14
Channel 15
Channel 15
Channel 16
Channel 16
74
Channel 2
INTRODUCTION
Brightest LED moving beam in its class
02
15
www.eklights.com
MASTER/SLAVE OPERATION
INTRODUCTION
SLAVE UNITS
SLAVE 1
SLAVE 2
SLAVE 3
SLAVE 4
...
N
1
2
5
3
6
4
1. Power Indicator
6. DMX 3 pin In/Out
2. DMX Indicator
7. Fuse:T1A 250V
3. UFI: UFI- Wireless Function
8. POWER CON IN/OUT
7
8
4.Display:OLED Display
5.Buttons:Mode、UP、Down、Enter
Display Function Navigation
MASTER UNIT
14
Mode
Illustration
Function Description
Menu
Menu Options
Enter the Menu
Up
Up
Scroll Up
Increase the numeric value
Down
Down
Scroll Down
Decrease the numeric value
Menu Operation
Enter
Save the function
OK
Save the function
03
www.eklights.com
DMX CHANNELS
INSTALLATION
Safety Cable
mp
Mounting Cla
Truss
t
Omega Bracke
8. Color
DMX CONNECTION
DMX512 Controller
9. Prism Rot
10. Control
Subsequent
04
03
000- 004
005- 008
009-012
013- 016
017- 021
022- 025
026- 029
030- 033
034- 038
039- 042
043-046
047- 050
051- 055
056- 059
060-063
064- 067
068- 071
072- 076
077- 080
081- 084
085- 088
089- 093
094- 097
098 -101
102- 105
106- 110
111- 114
115- 118
119- 122
123- 127
128- 189
190- 193
194- 255
000-005
006-191
192-223
224-255
000-039
040-049
050-059
060-069
070-079
080-089
090-099
100-109
110-119
120-199
200-209
210-255
Open
Open+Color1
Color 1
Color 1 + Color 2
Color 2
Color 2 + Color 3
Color 3
Color 3 + Color 4
Color 4
Color 4 + Color 5
Color 5
Color 5 + Color 6
Color 6
Color 6 + Color 7
Color 7
Color 7 + Color 8
Color 8
Color 8 + Color 9
Color 9
Color 9 + Color 10
Color 10
Color 10 + Color 11
Color 11
Color 11 + Color 12
Color 12
Color 12 + Color 13
Color 13
Color 13 + Color 14
Color 14
Color 14 + Open
Stop to fast(Forward Spin)
Stop Rotation
Fast to stop (Reverse Spin)
Open
Insertion and Positioning from 0-360 degrees
Stop to fastest (Forward Spin)
Fastest to stop (Reverse Spin)
No function
Enable blackout while Pan/Tilt move (Hold 3 Second)
Disable blackout while Pan/Tilt move (Hold 3 Second)
Enable blackout while color change (Hold 3 Second)
Disable blackout while color change (Hold 3 Second)
Pan Reset (Hold 3 Second)
Tilt Reset (Hold 3 Second)
Color Reset (Hold 3 Second)
Prism Reset (Hold 3 Second)
No function
Reset all (Hold 3 Second)
No function
13
www.eklights.com
DMX CHANNELS
7.Prism Rot.
8.Control
000-005
006-191
192 -223
224 -255
000-039
040-049
050-059
060-069
070-079
080-089
090-099
100-109
110 -119
120-199
200-209
210-255
POWER CONNECTION
Open
Insertion and Positioning from 0-360 degrees
Stop to fastest (Forward Spin)
Fastest to stop (Reverse Spin)
No function
Enable blackout while Pan/Tilt move (Hold 3 Second)
Disable blackout while Pan/Tilt move (Hold 3 Second)
Enable blackout while color change (Hold 3 Second)
Disable blackout while color change (Hold 3 Second)
Pan Reset (Hold 3 Second)
Tilt Reset (Hold 3 Second)
Power In
WARNING
Color Reset (Hold 3 Second)
Prism Reset (Hold 3 Second)
No function
Reset all (Hold 3 Second)
No function
3. Tilt
5. Movement
6. Shutter
7.Dimmer
Power out
Do not connect more than 71 units in serieswith one power cable.
Do not use damaged power cables.
Turn off the power when the units are not in use.
DMX CONNECTION
DMX512 Controller
10CH
Function
1. Pan
Using POWER CON In/Out
Power cable connected in series
Attention:due to the power rating
one 1.5mm² power cable can connect 71 units maximum
Value
000-255
000-255
000-255
000-255
000-255
000-010
011-030
031-085
086-105
106-160
161-180
181-235
236-255
000-255
Percent/Setting
Remark
COMMON
DMX INPUT
1
3
2
Fastest to slowest
Shutter closed
No function (shutter open)
DMX十
2
1
3
2
DMX一
DMX OUTPUT
3
1
No function (shutter open)
No function (shutter open)
No function (shutter open)
0~100%
12
03
Relation between DMX and Address
MODE
ALLOCATION
8CH
001 -008
001
009
017
025
10CH
001 -010
001
011
021
031
STARTING ADDRESS STARTING ADDRESS STARTING ADDRESS STARTING ADDRESS
1ST FIXTURE
2ND FIXTURE
3RD FIXTURE
4TH FIXTURE
05
03
www.eklights.com
DMX CHANNELS
TECHNICAL SPECIFICATION
8CH
Function
1. Pan
2. Tilt
3. Movement
PHOTOMETRICS
Light Source:
Beam Angle:
Output:
14W 6200K LED
2.5°
19080 LUX @ 5 meters
4. Shutter
POWER
Mains:
Consumption:
Power connections:
Power linking:
100 - 240 VAC, 50/60 Hz
38W
PowerCon In/Out
Up to 71 units @ 230V
5. Dimmer
KEY FEATURES
Pan movement:
Tilt movement:
Color Wheel:
Strobe:
Dimming:
Prism:
CONTROL
Protocol:
DMX channels:
Data connections:
Dispaly:
540°
270°
14 + Open
1 - 30Hz
4 dimming curve modes
8-facet, bi-directional
variable-speed rotation
6. Color
DMX512 ,UFI
8 / 10
3-pin XLR In/Out
OLED display with 4-button navigation
PHYSICAL
Size:
Weight:
IP:
228*174*348mm
5.23kg
20
06
03
Value
000-255
000-255
000-255
000-010
011-030
031-085
086-105
106-160
161-180
181-235
236-255
000-255
000-004
005-008
009-012
013-016
017-021
022-025
026-029
030-033
034-038
039-042
04 3-046
047-050
051-055
056-059
060-063
064-067
068-071
072-076
077-080
081-084
085-088
089-093
094-097
098-101
102-105
106-110
111-114
115-118
119-122
123-127
128-189
190-193
194-255
Percent/Setting
Fastest to slowest
Shutter closed
No function (shutter open)
Strobe effect slow to fast
No function (shutter open)
Pulse-effect in sequences
No function (shutter open)
Random strobe effect slow to fast
No function (shutter open)
0~100%
Open
Open+Color1
Color 1
Color 1 + Color 2
Color 2
Color 2 + Color 3
Color 3
Color 3 + Color 4
Color 4
Color 4 + Color 5
Color 5
Color 5 + Color 6
Color 6
Color 6 + Color 7
Color 7
Color 7 + Color 8
Color 8
Color 8 + Color 9
Color 9
Color 9 + Color 10
Color 10
Color 10 + Color 11
Color 11
Color 11 + Color 12
Color 12
Color 12 + Color 13
Color 13
Color 13 + Color 14
Color 14
Color 14 + Open
Stop to fast(Forward Spin)
Stop Rotation
Fast to stop (Reverse Spin)
11
03
Remark
www.eklights.com
PHOTOMETRICS
MENU DESCRIPTION
2.SETUP
Beam Angle: 2.56°
(1)Movement
1. Pan Inverse and Tilt Inverse setting
2. Pan Feedback and Tilt Feedback setting
(2)Screen
1.Back Light :set delay time for menu display to go dark at either 10,20 or 30 seconds or choose always ON.
2.Flip Display
3.Warning Cue
4.Key Lock:password: UP DOWN UP DOWN ENTER
(3)Fixture
1.Fan Mode: fan speed setting
2.Temperature
(4). AUTO TSET
FULL on
Project Distance(m)
3m
Luminance(lux)
53000
Distance(m)
3
5
53000
Full on
19080
5m
19080
7m
10m
10
7
15
9374
(5). Manual Test
3. ADVANCED
(1).Reset
1.All:reset all the steps
2.reset seperate step
(2).Adjust
COLOR
(3).Factory Reload
Restore factory settings
4.INFORMATION
Red
Bule
Yellow
Green
Light Orange
Magenta
Cyan
CTO
Dark Green
CTB
Pink
Light Green
Orange
UV
(1).Fixture Time(0-9999)
(2).Temperature
(3).Fan speed
(4).Software Version
(5).UID
5.STAND ALONE
(1).Master/slave
(2).play:built-in programs (show1-4)
(3)MIC Sens:0-100
10
03
07
03
15m
9374
www.eklights.com
MENU
NO. Main Menu
1
CONNECT
MENU
Menu level 2
Menu level 3
DMXAddress
1- 512
Menu level 4
Default: 001
8CH
DMXMode
Remark
Default: 10CH
10CH
Pan Reverse
Tilt Reverse
Movement
Pan Feedback
Tilt Feedback
Back Light
Screen
2
Flip Display
SETUP
Warn Cue
Key Lock
Auto Test
Manual Test
Auto Test...
Pan
Pan Fine
Tilt
Tilt Fine
Pan/Tilt Speed
Dimmer
Shutter
Color
Prism
08
03
Reset
No
Yes
No
Yes
No
Yes
No
Yes
On
10S
20S
30S
No
Yes
O
On
No
Yes
000- 255
000- 255
000- 255
000- 255
000- 255
000- 255
000- 255
000- 255
000- 255
3
ADVANCED
Default: No
Adjust
Default: No
Factory Reload
Default: Yes
Fixture Time
Temperature
Fans speed
Default: Yes
Default: On
4
INFORMATION
Software Version
UID
Default: No
All
Pan
Tilt
Color
Prism
Pan O set
Tilt O set
Color O set
Prism O set
No
Yes
0- 9999
58° C
**%
DISP V1.0
CTR- XY V1.0
CTR- LED V1.0
Default: On
5
STAND ALONE
Play
Sequence
Mic Sens
Default:
MENU DESCRIPTION
Tilt: 128
Dimmer: 255
Strobe: 255
1.CONNECT
Default: No
Default: 0
030F0210***
Maser/Slave
Default: No
000- 255
000-255
000- 255
000- 255
Maser
Slave
Show 1
Show 2
Show 3
Show 4
000- 100
(1)DMX Address: Set DMX starting address from a value between 1-502
DMX Mode: Selectable DMX mode 8/10 channels
09
03
Default: Slave
Default: Show 1
Default: 85
Download PDF
Similar pages
CLASSE LS 4O
battery replacement
XT STUB Eternal Lighting User Manual
giotto digital 1500 - Techni-Lux
Eternal Lighting Mitter Pro™
LEDDANCER48 User Manual
525 Kb Manual_C8
Untitled - Red Lighting