Smeg S7323LFEP Tam Entegre Buzdolabı Kullanma - Smeg-TR

Gebruik‐
saanwijzing
User Manual
Notice d'utili‐
sation
Benutzerin‐
formation
Koelkast
Refrigerator
Réfrigérateur
Kühlschrank
S7323LFEP
18
CONTENTS
Safety information
Safety instructions
Operation
Daily use
Hints and tips
18
19
21
22
23
Care and cleaning
Troubleshooting
Installation
Noises
Technical information
23
24
27
31
32
Subject to change without notice.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible
if an incorrect installation and use causes injuries and
damages. Always keep the instructions with the appliance for
future reference.
Children and vulnerable people safety
•
•
•
•
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved.
Do not let children play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
Keep all packaging away from children.
General Safety
•
•
This appliance is intended to be used in household and
similar applications such as:
– Farm houses; staff kitchen areas in shops, offices and
other working environments
– By clients in hotels, motels, bed and breakfast and other
residential type environments
Keep ventilation openings, in the appliance enclosure or in
the built-in structure, clear of obstruction.
19
•
•
•
•
•
•
•
Do not use mechanical devices or other means to accelerate
the defrosting process, other than those recommended by
the manufacturer.
Do not damage the refrigerant circuit.
Do not use electrical appliances inside the food storage
compartments of the appliance, unless they are of the type
recommended by the manufacturer.
Do not use water spray and steam to clean the appliance.
Clean the appliance with a moist soft cloth. Only use neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
Do not store explosive substances such as aerosol cans
with a flammable propellant in this appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
SAFETY INSTRUCTIONS
Installation
WARNING! Only a qualified
person must install this
appliance.
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Obey the installation instruction supplied
with the appliance.
• Always be careful when you move the
appliance because it is heavy. Always
wear safety gloves.
• Make sure the air can circulate around
the appliance.
• Wait at least 4 hours before connecting
the appliance to the power supply. This
is to allow the oil to flow back in the
compressor.
• Do not install the appliance close to
radiators or cookers, oven or hobs.
• The rear of the appliance must stand
against the wall.
• Do not install the appliance where there
is direct sunlight.
• Do not install this appliance in areas that
are too humid or too colds, such as the
construction appendices, garages or
wine cellars.
• When you move the appliance, lift it by
the front edge to avoid scratching the
floor.
Electrical connection
WARNING! Risk of fire and
electrical shock.
• The appliance must be earthed.
• Make sure that the electrical information
on the rating plate agrees with the
power supply. If not, contact an
electrician.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
electrical components (e.g. mains plug,
mains cable, compressor). Contact the
Authorised Service Centre or an
20
electrician to change the electrical
components.
• The mains cable must stay below the
level of the mains plug.
• Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
Use
WARNING! Risk of injury,
burns, electrical shock or fire.
• Do not change the specification of this
appliance.
• Do not put electrical appliances (e.g. ice
cream makers) in the appliance unless
they are stated applicable by the
manufacturer.
• Be careful not to cause damage to the
refrigerant circuit. It contains isobutane
(R600a), a natural gas with a high level of
environmental compatibility. This gas is
flammable.
• If damage occurs to the refrigerant
circuit, make sure that there are no
flames and sources of ignition in the
room. Ventilate the room.
• Do not let hot items to touch the plastic
parts of the appliance.
• Do not store flammable gas and liquid in
the appliance.
• Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.
• Do not touch the compressor or the
condenser. They are hot.
Care and cleaning
WARNING! Risk of injury or
damage to the appliance.
• Before maintenance, deactivate the
appliance and disconnect the mains
plug from the mains socket.
• This appliance contains hydrocarbons in
the cooling unit. Only a qualified person
must do the maintenance and the
recharging of the unit.
• Regularly examine the drain of the
appliance and if necessary, clean it. If
the drain is blocked, defrosted water
collects in the bottom of the appliance.
Disposal
WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door to prevent children
and pets to be closed inside of the
appliance.
• The refrigerant circuit and the insulation
materials of this appliance are ozonefriendly.
• The insulation foam contains flammable
gas. Contact your municipal authority for
information on how to discard the
appliance correctly.
• Do not cause damage to the part of the
cooling unit that is near the heat
exchanger.
21
OPERATION
Control panel
1
2
4
1
2
3
4
Temperature indicator LED
IntensiveCooling indicator
IntensiveCooling button
Temperature regulator
ON/OFF button
3
Switching on
1. Insert the plug into the wall socket.
2. Touch the temperature regulator button
if all LED are off.
Switching off
Keep touching the temperature regulator
button for 3 seconds.
All indicators light off.
Temperature regulation
To operate the appliance, touch the
temperature regulator button until the LED
corresponding to the required temperature
lights up. Selection is progressive, varying
from 2 to 8°C.
At first button touch actual setting LED
keeps blinking.
Any time the button is touch the set
temperature is moved to 1 position .
Corresponding LED will blink for a while.
Touch the setting button until the required
temperature is selected. The set will be
fixed
Coldest setting: +2°C.
Warmest setting: +8°C.
A medium setting is generally
the most suitable.
However, the exact setting should be
chosen keeping in mind that the
temperature inside the appliance depends
on:
• room temperature
• how often the door is opened
• quantity of food stored
• appliance location.
IntensiveCooling function
You can activate IntensiveCooling function
by pressing the IntensiveCooling.
The LED corresponding to the symbol
IntensiveCooling indicator lights up.
You can deactivate IntensiveCooling
function by pressing the IntensiveCooling
again.
The IntensiveCooling indicator will light off.
This function stops automatically
after 52 hours.
22
DAILY USE
WARNING! Refer to Safety
chapters.
Movable shelves
The walls of the refrigerator are equipped
with a series of supports so that the shelves
can be positioned as desired.
Positioning the door shelves
To permit storage of food packages of
various sizes, the door shelves can be
placed at different heights.
To make these adjustments proceed as
follows:
1. Gradually pull the shelf in the direction
of the arrows until it comes free.
If “OK” is displayed (A), put fresh food into
area indicated by symbol, if not (B), adjust
the temperature controller to a colder
setting and wait 12 hours before checking
the temperature indicator again.
A
OK
B
OK
After putting fresh food into the
appliance or after opening the
door repeatedly or for a long
period, it is normal for the
indicator not to show "OK"; wait
at least 12 hours before
readjusting the temperature
controller.
Fan function
The fan function let food cool quickly and a
more uniform temperature in the
compartment.
Switch on the fan when the
ambient temperature exceeds
25°C.
Press the switch (A) to switch on the fan.
The green light (B) comes on.
A
2. Reposition the shelf as required.
Temperature indicator
For proper storage of food the refrigerator is
equipped with the temperature indicator.
The symbol on the side wall of the
appliance indicates the coldest area in the
refrigerator.
B
23
When you switch off the
appliance remember to turn off
the fan by pressing (A).
The green light (B) comes off.
HINTS AND TIPS
Normal operating sounds
The following sounds are normal during
operation:
• A faint gurgling and bubbling sound from
coils sound when refrigerant is pumped.
• A whirring and pulsating sound from the
compressor when refrigerant is pumped.
• A sudden cracking noise from inside
appliance caused by thermic dilatation (a
natural and not dangerous physical
phenomenon).
• A faint click noise from the temperature
regulator when the compressor switches
on or off.
Hints for energy saving
• Do not open the door frequently or leave
it open longer than absolutely necessary.
• If the ambient temperature is high and
the Temperature Regulator is set to low
temperature and the appliance is fully
loaded, the compressor may run
continuously, causing frost or ice on the
evaporator. If this happens, set the
Temperature Regulator toward warmer
settings to allow automatic defrosting
and so a saving in electricity
consumption.
Hints for fresh food refrigeration
• do not store warm food or evaporating
liquids in the refrigerator
• do cover or wrap the food, particularly if
it has a strong flavour
• position food so that air can circulate
freely around it
Hints for refrigeration
Useful hints:
• Meat (all types) : wrap in polythene bags
and place on the glass shelf above the
vegetable drawer.
• For safety, store in this way only one or
two days at the most.
• Cooked foods, cold dishes, etc..: these
should be covered and may be placed
on any shelf.
• Fruit and vegetables: these should be
thoroughly cleaned and placed in the
special drawer(s) provided.
• Butter and cheese: these should be
placed in special airtight containers or
wrapped in aluminium foil or polythene
bags to exclude as much air as possible.
• Bottles: these need a cap and should be
stored on the door bottle shelf, or (if
equipped) on the bottle rack.
• Bananas, potatoes, onions and garlic, if
not packed, must not be kept in the
refrigerator.
To obtain the best performance:
CARE AND CLEANING
WARNING! Refer to Safety
chapters.
General warnings
CAUTION! Unplug the
appliance before carrying out
any maintenance operation.
24
This appliance contains
hydrocarbons in its cooling unit;
maintenance and recharging
must therefore only be carried
out by authorized technicians.
The accessories and parts of
the appliance are not suitable for
washing in a dishwasher.
Periodic cleaning
every time the motor compressor stops,
during normal use. The defrost water drains
out through a trough into a special
container at the back of the appliance, over
the motor compressor, where it evaporates.
It is important to periodically clean the
defrost water drain hole in the middle of the
refrigerator compartment channel to
prevent the water overflowing and dripping
onto the food inside.
CAUTION! Do not pull, move or
damage any pipes and/or
cables inside the cabinet.
CAUTION! Take care of not to
damage the cooling system.
CAUTION! When moving the
cabinet, lift it by the front edge
to avoid scratching the floor.
The equipment has to be cleaned regularly:
1. Clean the inside and accessories with
lukewarm water and some neutral soap.
2. Regularly check the door seals and
wipe clean to ensure they are clean and
free from debris.
3. Rinse and dry thoroughly.
4. If accessible, clean the condenser and
the compressor at the back of the
appliance with a brush.
This operation will improve the
performance of the appliance and save
electricity consumption.
Defrosting of the refrigerator
Frost is automatically eliminated from the
evaporator of the refrigerator compartment
TROUBLESHOOTING
WARNING! Refer to Safety
chapters.
Periods of non-operation
When the appliance is not in use for long
periods, take the following precautions:
1. Disconnect the appliance from
electricity supply.
2. Remove all food.
3. Clean the appliance and all accessories.
4. Leave the door/doors open to prevent
unpleasant smells.
WARNING! If the cabinet will be
kept on, ask somebody to
check it once in a while to
prevent the food inside from
spoiling in case of a power
failure.
25
What to do if...
Problem
Possible cause
Solution
The appliance does not operate.
The appliance is switched
off.
Switch on the appliance.
The mains plug is not connected to the mains socket
correctly.
Connect the mains plug to the
mains socket correctly.
There is no voltage in the
mains socket.
Connect a different electrical
appliance to the mains socket.
Contact a qualified electrician.
The appliance is noisy.
The appliance is not supported properly.
Check if the appliance stands
stable.
The lamp does not work.
The lamp is in stand-by.
Close and open the door.
The lamp does not work.
The lamp is defective.
Contact the nearest Authorised
Service Centre.
The compressor operates
continually.
Temperature is set incorrectly.
Refer to "Operation" chapter.
Many food products were
put in at the same time.
Wait some hours and then
check the temperature again.
The room temperature is
too high.
Refer to climate class chart on
the rating plate.
Food products placed in
the appliance were too
warm.
Allow food products to cool to
room temperature before storing.
The door is not closed correctly.
Refer to "Closing the door".
The IntensiveCooling function is switched on.
Refer to "IntensiveCooling function".
The door is not closed correctly or the gasket is deformed/dirty.
Refer to "Closing the door".
The water drainage plug is
not correctly positioned.
Position the water drainage
plug in the correct way.
Food products are not
wrapped properly.
Wrap the food products better.
Temperature is set incorrectly.
Refer to "Operation" chapter.
There is too much frost and
ice.
26
Problem
Possible cause
Solution
The compressor does not
start immediately after pressing the IntensiveCooling, or
after changing the temperature.
This is normal, no error has
occurred.
The compressor starts after a
period of time.
Water flows on the rear plate
of the refrigerator.
During the automatic defrosting process, frost
melts on the rear plate.
This is correct.
Water flows inside the refrigerator.
The water outlet is clogged.
Clean the water outlet.
Food products prevent that
water flows into the water
collector.
Make sure that food products
do not touch the rear plate.
Water flows on the floor.
The melting water outlet is
not connected to the evaporative tray above the compressor.
Attach the melting water outlet
to the evaporative tray.
Temperature cannot be set.
The NO REFERENCE TO
FREEZING FUNCTION or
IntensiveCooling function is
switched on.
Switch off NO REFERENCE TO
FREEZING FUNCTION or IntensiveCooling manually, or
wait until the function resets
automatically to set the temperature. Refer to "NO REFERENCE TO FREEZING FUNCTION or IntensiveCooling function".
The temperature in the appliance is too low/too high.
The temperature regulator
is not set correctly.
Set a higher/lower temperature.
The door is not closed correctly.
Refer to "Closing the door".
The food products' temperature is too high.
Let the food products temperature decrease to room temperature before storage.
Many food products are
stored at the same time.
Store less food products at the
same time.
The door has been opened
often.
Open the door only if necessary.
The IntensiveCooling function is switched on.
Refer to "IntensiveCooling function".
There is no cold air circulation in the appliance.
Make sure that there is cold air
circulation in the appliance.
27
If the advice does not lead to
the desired result, contact the
nearest Authorised Service
Centre.
Replacing the lamp
The appliance is equipped with a longlife
LED interior light.
Closing the door
1. Clean the door gaskets.
2. If necessary, adjust the door. Refer to
"Installation".
3. If necessary, replace the defective door
gaskets. Contact the Authorised
Service Centre.
Only service is allowed to replace the
lighting device. Contact your Authorised
Service Centre.
INSTALLATION
Positioning
This appliance can be installed in a dry, well
ventilated indoor where the ambient
temperature corresponds to the climate
class indicated on the rating plate of the
appliance:
Climate
class
Ambient temperature
SN
+10°C to + 32°C
N
+16°C to + 32°C
ST
+16°C to + 38°C
T
+16°C to + 43°C
Some functional problems might
occur for some types of models
when operating outside of that
range. The correct operation
can only be guaranteed within
the specified temperature range.
If you have any doubts
regarding where to install the
appliance, please turn to the
vendor, to our customer service
or to the nearest Authorised
Service Centre.
Electrical connection
• Before plugging in, ensure that the
voltage and frequency shown on the
rating plate correspond to your domestic
power supply.
• The appliance must be earthed. The
power supply cable plug is provided with
a contact for this purpose. If the
domestic power supply socket is not
earthed, connect the appliance to a
separate earth in compliance with
current regulations, consulting a qualified
electrician.
• The manufacturer declines all
responsibility if the above safety
precautions are not observed.
• This appliance complies with the E.E.C.
Directives.
Ventilation requirements
The airflow behind the appliance must be
sufficient.
5 cm
min.
200 cm2
min.
200 cm2
28
CAUTION! Refer to the
assembly instructions for the
installation.
x
Door reversibility
The door of the appliance opens to the
right. If you want to open the door to the
left, follow these steps before you install the
appliance:
x
1. Loosen and remove the upper pin.
2. Install the appliance in the niche.
3. Push the appliance in the direction of
the arrows (1) until the upper gap cover
stops against the kitchen furniture.
2.
3.
4.
5.
Remove the door.
Remove the spacer.
With a key, loosen the lower pin.
Tighten the lower pin on the opposite
side.
2
1
6. Install the spacer.
7. Install the door.
8. Tighten the upper pin.
Installing the appliance
CAUTION! Make sure that the
mains cable can move freely.
1. If necessary cut the adhesive sealing
strip and then apply it to the appliance
as shown in figure.
4. Push the appliance in the direction of
the arrows (2) against the cupboard on
the opposite side of the hinge.
5. Adjust the appliance in the niche.
Make sure that the distance between
the appliance and the cupboard frontedge is 44 mm.
The lower hinge cover (in the
accessories bag) makes sure that the
distance between the appliance and the
kitchen furniture is correct.
Make sure that the clearance between
the appliance and the cupboard is 4
mm.
6. Open the door. Put the lower hinge
cover in position.
29
C
D
E
4mm
E
44mm
B
7. Attach the appliance to the niche with 4
screws.
I
10. Install the vent grille (B).
11. Attach the hinge covers (E) to the hinge.
12. Disconnect the parts (Ha), (Hb), (Hc)
and (Hd).
Hb
Ha
I
Hc
Hd
8. Remove the correct part from the hinge
cover (E). Make sure to remove the part
DX, in the case of right hinge, SX in
opposite case.
13. Install the part (Ha) on the inner side of
the kitchen furniture.
ca. 50 mm
90°
21 mm
90°
ca. 50 mm
21 mm
14. Push the part (Hc) on the part (Ha).
9. Attach the covers (C, D) to the lugs and
the hinge holes.
30
19. Place the small square on the guide
again and fix it with the screws
supplied.
20. Align the kitchen furniture door and the
appliance door by adjusting the part
(Hb).
Ha
Hc
15. Open the appliance door and the
kitchen furniture door at an angle of
90°.
16. Insert the small square (Hb) into guide
(Ha).
17. Put together the appliance door and the
furniture door and mark the holes.
Hb
21. Press the part (Hd) on the part (Hb).
8 mm
Hb
Ha
Hd
Hb
18. Remove the brackets and mark a
distance of 8 mm from the outer edge
of the door where the nail must be fitted
(K).
8 mm
K
Ha
Do a final check to make sure that:
• All screws are tightened.
• The sealing strip is attached tightly to the
cabinet.
• The door opens and closes correctly.
31
NOISES
There are some sounds during normal running (compressor, refrigerant circulation).
SSS
RRR
!
HISSS!
OK
UB
BL
SSSRRR!
HISSS!
SSSRRR!
HISSS!
B!
CLICK!
BRRR!
ICK
CL
!
BRRR!
CR
AC
CLICK!
BRRR!
K!
32
BLUBB!
CRACK!
BLUBB!
CRACK!
TECHNICAL INFORMATION
Technical data
Dimensions of the recess
Height
mm
1780
Width
mm
560
Depth
mm
550
Voltage
Volts
230 - 240
Frequency
Hz
50
The technical information are situated in the
rating plate, on the external or internal side
of the appliance and in the energy label.
ENVIRONMENT CONCERNS
Recycle the materials with the symbol .
Put the packaging in applicable containers
to recycle it. Help protect the environment
and human health and to recycle waste of
electrical and electronic appliances. Do not
dispose appliances marked with the symbol
with the household waste. Return the
product to your local recycling facility or
contact your municipal office.
Download PDF

advertising