SilverOnyx 3-in-1 HEPA H13 Air Cleaner

SilverOnyx
3-in-1 HEPA H13 Air Cleaner
SO-6011
User Manual
Contents
1. Important safety information …… … ……… … ……… … ………01
2. Product Structure……… … ……… … ……… … ……… … ……… …02
3. Before first use … ……… … ……… … …… … ……… … ……… … …03
4. Using the appliance… ……… … …… … ……… … ……… … ………05
5. Filter Replacement … … ……… … ……… … ……… … ……… … …0 7
6. Storage ……… … ……… … …… … ……… … ……… … ……… … ……09
7. Environment …… … ……… … ……… ……… … ……… … ……… … 09
8. Troubleshooting……… … ……… ……… … ……… … ………………09
1. Important safety information
Read this user manual carefully before you use the appliance and save it for future
reference.
Danger
●
●
Do not let water or any other liquid or flammable detergent enter the appliance to avoid electric shock
and/or a fire hazard.
Do not clean the appliance with water or any other liquid or a (flammable) detergent to avoid electric shock
and/or a fire hazard.
Warning
●
●
●
●
●
●
Check if the voltage indicated on the appliance corresponds to the local mains voltage before you connect the
appliance.
If the mains cord is damaged, you must have it replaced by distributor, or a service centre authorised by
distributor or similarly qualified persons in order to avoid a hazard.
Do not use the appliance if the plug, the mains cord or the appliance itself is damaged.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not block the air inlet and outlet, e.g. by placing items on the air outlet or in front of the air inlet.
Caution
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
This appliance is not a substitute for proper ventilation, regular vacuum cleaning or use of an extractor hood or
fan while cooking.
If the wall socket used to power the appliance has poor connections, the plug of the appliance becomes hot.
Make sure you plug the appliance into a properly connected wall socket.
Always place and use the appliance on a dry, stable, level and horizontal surface.
Leave at least 40cm free space behind and on both sides of the appliance and leave at least 40cm free space
above the appliance.
Do not place anything on top of the appliance and do not sit on the appliance.
Do not place the appliance directly below an air conditioner to prevent condensation from dripping onto the
appliance.
Make sure all filters are properly installed before you switch on the appliance.
Only use the original filters specially intended for this appliance. Do not use any other filters.
Avoid knocking against the appliance (the air inlet and outlet in particular) with hard objects.
Always lift or move the appliance by the handle at the back of the appliance.
Do not insert your fingers or objects into the air outlet.
Do not use this appliance when you have used indoor smoke-type insect repellents or in places with oily
residues, burning incense or chemical fumes.
Do not use the appliance near gas appliances, heating devices or fireplaces.
Always unplug the appliance after use and before you clean it.
Do not use the appliance in a room with major temperature changes, as this may cause condensation inside the
appliance.
The appliance is only intended for household use under normal operating conditions.
Do not use the appliance in wet surroundings or in surroundings with high ambient temperatures, such as the
bathroom, toilet or kitchen.
The appliance does not remove carbon monoxide (CO) or radon (Rn). It cannot be used as a safety device in
case of accidents with combustion processes and hazardous chemicals.
To prevent interference, keep at least 2 meters distance between the product and the use of radio waves
electrical.
01
2. Parts Diagram
Before use please read this manual carefully to operate the product
correctly.
1
2
3
4
5
6
7
8
8.1
8.2
9
1. Outlet cover
2. Control panel
3. Upper body
4. Decorative ring
5. Electric outlet
6. Lower body
7. Anion generator
8. Combination filter
8.1 HEPA
8.2 Nano silver pre-filter
9. Base cover
02
3. Before first use
Placing the filters
The appliance comes with all filters fitted inside, but you have to remove
the packaging of the filters before you can use the appliance. Remove all
filters, unpack them and place them back into the appliance as described
below.
Note: Make sure you insert the filters in the correct position.
1. Put the appliance upside down on a soft cloth to avoid scratching, to
open the base cover, you need to find an arrow point
on the base cover
corresponding the LOCK position, turn the base cover counterclockwise
from LOCK to OPEN position, then the lock released.
2. Remove the base cover and take out the combination filters.
3. Remove the packaging material from the filter.
03
4. Put the filter back into the appliance.
Note: Make sure that the side with the tag is pointing towards you.
Tag
5. Turn the base cover clockwise from OPEN position to LOCK position,
you will hear a "click" sound, the base cover is fastened.
04
4. Using the appliance
4.1 About the control panel
On/Off
Anion
Filter
Speed
1. Put the plug in the wall socket
All lights go on once and you hear a beep.
Then the lights go out again.
2. Press the power button to switch on the appliance.
The power
lights and FAN SPEED 2 light (mid) on
the control panel go on.
3. Filter replacement light
When indicator
lights, it means that you should check the filter if it need
to be cleaned or replaced.
Note: The filters’ lifetime is based to your house air quality and using time.
Using the appliance in a humid environment will reduce the lifetime of HEPA filter.
4. Fan speed adjustment
The fan speed light indicates at which fan speed the appliance is operating.
Press Speed button
to adjust fan speed level, there are three levers
1~3 refers to Low, Medium and High level.
5. Anion mode
When the appliance is switched on, press
button to start Anion mode,
the appliance will release 6 millions of Anions per second to make the air
fresh.
Press
button again to switch off.
05
4. 2 Night Light (Optional)
If your appliance have the night light, when you press
the
button, the night light will turn on, touch the
center of the outlet cover with the palm of your hand,
the light will be dimmer, touch it again, the light will turn
off. Touch it once more, the light will turn on. Repeat the
above step to adjust its brightness or on-off.
When you press
button to switch off the appliance,
the night light will also be turned off.
4. 3 Clean air purifier
Regularly clean the inside and outside of the body to prevent dust from
collecting on the inside and outside.
1). Wipe away dust with a soft dry cloth from the body of the appliance.
2). Clean the air inlet and the air outlet with a soft dry cloth.
Note :
Always unplug the appliance before you clean it.
● Never immerse the appliance in water or any other liquid.
● Never use aggressive or flammable cleaning agents such as bleach or
alcohol to clean any part of the appliance.
● Only silver ion filter is washable,the HEPA filter is NOT washable and must
not get wet. To clean the HEPA filter, use a soft brush to remove debris or
vacuum gently.
●
06
5. Filter Replacement
1. Switch off the appliance and unplug it. (a)
(a)
2.Put the appliance upside down on a soft cloth to
avoid scratching, to open the base cover, you need
to find an arrow point
on the base cover
corresponding the LOCK position, turn the base
cover counterclockwise from LOCK to OPEN
position, then the lock released. (b)
(b)
3. To remove the base cover and combination
filter, grab filter tag and pull it towards you. (c)
(c)
Tag
4. Remove the packaging material of the new
combination filter. (d)
(d)
5. Put the new filter back into the appliance. (e)
Note:For HEPA filter
Make sure that the side with the tag is
pointing towards you.
(e)
07
Tag
6. Turn the base cover clockwise from OPEN
position to LOCK position, you will hear a "click"
sound, the base cover is fastened. (f)
(f)
7.Put the plug in the wall socket and switch
on the appliance again. (g)
(g)
8.Reset Filter's lifetime.
Even you replace the filters, when you switch on
the appliance, the filter icon still light, you need to
reset the filter’s lifetime, so that the appliance can
cycle to calculate the filters’ working time.
Press and hold the
button for 3 seconds, the (h) 3 seconds
filter light turn off, the reset is finished. (h)
Filter replacement force mode
Suppose you use the appliance under air pollution environment, you can
replace the filter even the filter icon does not light, the filter replacing
method is same, please see chapter: Filter replacement.
To force reset the filter’s lifetime:
At the standby model(NOT press the power button), press and hold
button for 3 seconds, the icon
light on, press and hold
button for 3
seconds again, the filter light turn off, then the reset is finished.
08
6. Storage
Unplug the power cord, then wipe the machine clean, put the appliance in
the packing bag ,then put it in a dry place away.
7. Environment
Do not throw away the appliance with the normal household waste at the
end of its life, but hand it in at an official collection point for recycling. By
doing this, you help to preserve the environment.
8. Troubleshooting
This chapter summarises the most common problems you could
encounter with the appliance. If you are unable to solve the problem with
the information below, contact the Consumer Care Centre in your country.
Problem
The appliance
doesn't work
Possible cause
Power plug is not connected to a
power supply
The power is not switch on
Filter ’s plastic packaging haven’ t
been removed
Outlet airflow
The fan speed is at the low level
significantly reduced
than before
The filter haven’
t be replaced
No suitable clearance and space for
ventilation in the surroundings
The room coverage has exceed
Poor performance or
applicable area
don’
t have good
Air inlet or outlet of the machine is
purification capacity
blocked
Possible solution
Unplug and then plug the power
again
Plug in the power and press on/off
button.
Filter’s plastic packaging should be
removed before use
Please press speed button to adjust
fan speed level
Replace a new filter
Make sure all the rear and up sides
each has 40cm space left
Use the air purifier in a room with
applicable area
Please remove the objects inlet and
outlet
After replacing filter
Press and hold the filter button for 3
the filter replacement Not reset the filter's lifetime correctly seconds, the filter light turn off, the
icon still light
reset is finished
09
SilverOnyx LLC
268 N Eastfield Circle, Alpine, UT 84004 USA
Tel
801-573-2197
Email admin@silveronyx.com
Web www.silveronyx.com
Download PDF

advertising