Direct Vent Gas Fireplaces Model Riviera-42

©
Direct Vent Gas Fireplaces
Model Riviera-42
Canadian Fire Hearth Mfg
Installation and Owner’s Manual
PLEASE READ INSTRUCTIONS CAREFULLY BEFORE
INSTALLING AND OPERATING THE APPLIANCE
WARNING: If the information in these instructions is not followed exactly, a fire or explosion may
result causing property damage, personal injury, or loss of life.
•Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
•This appliance may be installed in a permanent home, and is suitable for bedroom or sitting room.
IN THE EVENT THAT YOU SMELL GAS
Do not try to light any appliance
Do not touch electrical switches
Do not use any phone in your building
Call your gas supplier from a neighbor’s phone and
follow the gas supplier’s instructions
If you cannot reach the gas supplier, call the fire
department
FOR YOUR SAFETY
DO NOT store or use gasoline or any other
flammable vapors or liquids within the vicinity
of this or any other appliance
Installer: Please leave this manual with the customer
Customer: Please keep instructions for future reference
PLEASE NOTE: This product has been manufactured using steel and screws. As a result, there are
many sharp edges that can easily cut exposed skin. It is highly recommended that you wear proper
protective gloves while installing the unit, and during routine cleaning or maintenance.
1
Table of Contents
Page 1…………………………………………………………………….. .....Cover Page with Safety Information
Page 2………………………………………………………………………….Table of Contents
Page 3 & 4…………………………………………………………………......Customer Greeting & Safety Information
Page 5 ………………………………………………………………………....Features and Specifications
Page 6……………………………………………………………………….....Framing Specifications
Page 7………………………………………………………………………… Placement and Mantel Requirements
Page. 8…………………………………………… …………………………....Corner Installation / Supply Lines Specs.
Page 9………………………………………………………………………….Venting Components
Page 10…………………………………………………………………………Vertical Venting
Page 11…………………………………………………………………………Horizontal Venting
Page 12…………………………………………………………………………Exterior Vent Clearances
Page 13…………………………………………………………………………Installation Planning
Page 14…………………………………………………………………………Installing Non-Combustible Panels
Page 15 & 16…………………………………………………………………...Cleanface Mounting Instruction
Page 17…………………………………………………………………………Glass Door Removal/Re-attachment
Page 18………………………………………………………………………… Electrical
Page 19………………………………………………………………………….Lighting Instructions
Page 20………………………………………………………………………….Final Checks
Page 21………………………………………………………………………….Thermostat / Pilot Check
Page 22………………………………………………………………………….Flame Adjustment
Page 23………………………………………………………………………….Replacement Parts
Page 24………………………………………………………………………….Maintanance
Page 25………………………………………………………………………….Warranty
2
CONGRATULATIONS
Welcome to Our Luxor Gas Fireplace Family
We hope you’ve had an easy and enjoyable time choosing from our line of products, and we certainly
appreciate your business. Please take some time to read through the following information, and make
sure to heed all of the warnings. Even though our fireplaces are easy to install and simple to operate,
they are still gas burning units with some inherent dangers if not careful
Date Purchased:_____________________________
Dealer:__________________________________________________________________
Installer:________________________________________________________________
Phone:_________________________________ Serial Number:____________________
FOR YOUR SAFETY – Read before lighting
DO NOT: Use tools to operate controls. Use only your hand to push in and turn controls.
DO NOT: Abuse glass doors by striking or slamming shut.
DO NOT: Clean the appliance when hot.
DO NOT: Use this appliance if you smell gas.
DO NOT: Use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the
appliance and replace any part of the control system and any gas control which has been under water.
General Safety (Home Owner)
•Fire Extinguisher: Every home should have at least on fire extinguisher. An approved Class A-B-C extinguisher should be
mounted on the wall near an exit and close to the application, but not so close that accessibility to the extinguisher could be
blocked by a fire. Your local Fire Department can advise you concerning the most appropriate location.
•Smoke Detectors & Carbon Monoxide Detectors on each floor of your home to ensure your safety. It should be located away
from the gas appliance and close to the sleeping areas. Follow the detector’s manufacturer’s placement installation and
maintenance instructions.
Safety for the installer
Wear gloves and safety glasses for protection.
Exercise extreme caution when using ladders or
when on roof tops.
Be aware of electrical wiring locations in walls
and ceilings.
Use a back support for heavy lifting.
Vent safety
Venting must be installed according to local codes.
Electrical code
When installed, these appliances must be electrically grounded
in accordance with local codes.
3
This appliance is only for use with the Natural Gas and Propane as indicated on the rating plate.
Note: The copy in the manual is for reference only. In the event of a discrepancy, the label on the unit is to be
taken as the latest version.
GAS SUPPLY
ONLY PERSONS LICENSED TO WORK WITH GAS PIPING MAY MAKE THE NECESSARY GAS CONNECTION TO
THIS APPLIANCE. YOU ARE NOW READY TO HOOK UP THE GAS SUPPLY. BE SURE GAS PLUMBING
INSTRUCTIONS AND ALL PROVINCIAL AND LOCAL CODES ARE CAREFULLY FOLLOWED. USE APPROVED
FLEXIBLE GAS CONNECTIONS OR RIDGID PIPING, DEPENDING ON PROVINCIAL AND LOCAL CODES, TO
ATTACH BURNER TO GAS SUPPLY. BE SURE TO USE PROPER SIZE GAS SUPPLY LINE. CAREFULLY CHECK
ALL CONNECTIONS FOR GAS LEAKS WITH SOAP AND WATER SOLUTION.
EACH INSTALLATION MUST CONFORM TO ALL LOCAL, PROVINCIAL, AND NATIONAL CODES. REFER TO
THE NATIONAL FUEL GAS CODE, LOCAL ZONING AND CODE AUTHORITIES FOR DETAILS ON INSTALLATION
REQUIREMENTS.
WARNING
DO NOT burn ANY materials in this fireplace.
All occupants of the home, especially children, should be alerted about the hazards of the high surface
temperature and the chance of severe burning or the possible ignition of clothing.
Young children should be carefully supervised when they are in the same room as the appliance.
Due to the high temperatures, the fireplace should be installed away from the furniture and draperies and
out of traffic areas.
Nothing should ever be placed on or near the surface of the fireplace, including the top of the unit.
Clothing or other flammable material should not be placed on or near the appliance.
Make certain the control panel, burners, fans, and venting system are kept clean. Inspection of these
systems should be inspected annually by a qualified service technician.
Any safety screen or guard removed for servicing the appliance must be replaced prior to operating the
appliance.
The fireplace, under NO circumstances, should ever be modified.
Do not operate the fireplace if damaged, or if the glass is cracked. Any repairs must be done by a
certified technician.
Certification
The Model Riviera-42 is listed and certified for installation
in the U.S.A. and Canada under the following standards:
ANSI Z21.50/CSA 2.22.
The installation must conform with local codes or, in the
absence of local codes, with the National Fuel Gas and
Propane Installation Code, ANSI Z223.1 / NFPA 54 in the
US or the Natural Gas and Propane Installation Code, CSA
B149.1 in Canada.
Please contact Canadian Fire Hearth Manufacturing if you have any
questions regarding the certification of this appliance.
4
FEATURES AND SPECIFICATIONS
Note: Always check appliance label for correct information
MODEL: RIVIERA-42
Natural Gas
Manifold Pressure
1.6-3.5in w.c.
Min. Supply pressure
5.0in w.c.
for purpose of input adjustment
Max Supply pressure
11in w.c.
Orifice size
#44
Nominal input rating
High altitude (US)
High altitude (Canada)
Primary Air Opening
Electrical Rating
Steady State Efficiency
P.4.1 Annual Fireplace Efficiency
Circulating fan (optional)
Vent System
Glass
Clean Face Kit (required for all installations)
Propane
6.0-10.0in w.c.
11in w.c
13in w.c.
#58
22000 BTU/hr Heater Rated
0-2000ft / 0-610m
0-4500ft / 0-1370m
115 volts 0.7 amp 60hz
54.42%
53.64%
Variable Speed
Direct Vent
Ceramic
Black
Please Note: Only products supplied by the manufacturer may be used in the installation of this appliance.
The Luxor Riviera 42 is a direct vent gas
appliance utilizing an inclined vent for superior
installation flexibility. It enables either horizontal
or vertical vent installation without labouring to
convert over a dual type unit or having to
purchase a dedicated vent configuration.
5
Installation
Minimum Framing Dimensions
Rear Venting Exit Minimum. Center vertical
framing with appliance
Clearance to side walls is 0 inches
Metal support for Noncombustible facing
• Gas Inlet Location
6” from front by 3.5”
above floor.
•Electrical connection is
centered 10” from front at
3.5” from floor on each
side of the appliance
Note: To provide the easiest installation center the appliance between the vertical framing at the rear so the venting will be
centered. This will allow venting to pass through the framing without modifications.
Non-combustible panel must be
fastened to the top of any
combustible framing.
20.5” from floor or platform to the
frame opening Is lowest acceptable
measurement.
24” to the venting termination
center from either the floor or
exterior ground level is the
Minimum Allowable
Clearance
Framing the Rear Vent Opening at 14.25” square required for required Wall Thimble. Non-Combustible panel (supplied
by Canadian Fire Hearth) must be installed on the top of the opening.
6
Raised Fireplace Placement
Elevated Height Options
As the Riviera 42 contemporary design leads itself to
installations higher in the wall as would other traditional
appliances. All installations clearance still applies. Noncombustible panels and distances to combustible materials
must be adhered to. The Clearance to the ceiling must not
be less than the 44” inches dictated by the internal ceiling
height. Mantel sizes and clearance when applicable follow
guideline described in this manual.
Mantel Requirements
No Combustible materials are
permitted lower than 7 ¾” above
the opening of the appliance
represented by the hatch area. A
projection ( mantel or trim) of
combustible material can be no
deeper than 12” from the 7 ¾”
height.
Caution: any finish like stains or
clear coatings must be of a high
heat design to prevent
discolouration.
7
Corner Installation
A 45º angle installation
68.00
50.49
Typical venting configuration for
corner installation
15.25
Installing Gas and Electrical Supply Lines.
Both Gas and Electrical lines must be installed and accessible for the installation of the Riviera 42.
Natural Gas requires a minimum inlet gas pressure of 5.0 in W.C.. Liquid Propane Fuel requires a
minimum of 11.0 in. W.C. IMPORTANT: Installer please allow a portion of the gas line
connecting to the appliance to be flexible enough for moving and aligning the appliance into the
chase. It’s very advisable to connect and secure gas lines before attaching the Cleanface Front.
After securing the Cleanface to the appliance access to the gas compartment becomes limited.
A grounded 117volt AC line must be supplied to the appliance and wired into the electrical box
which is fixed to the right hand side of the appliance. This will supply power to the AC Adapter
which powers the Electronic Valve System. and also provides power for an optional electrical
blower if installed.
Framing and Clearance
Unit maybe installed in any location that maintains proper clearances to air conditioning ducts, electrical
wiring and plumbing. Safety, as well as efficiency of operation must be considered in selecting a fireplace
location. Select a location that does not interfere with room traffic, has adequate ventilation, and offers an
accessible pathway for venting installation.
8
Venting
Venting Parameters.
The Riviera 42 can be installed using either Canadian Firehearth Rigid 5 x 8 co-axial venting or 2-ply
Aluminum Chimney liner that is supplied by Canadian Firehearth. A description of the details and
limitation for venting are listed in ths manual. Installer please note; there are variations with venting
configurations specific to either Natural gas or Propane Fuels. The implementation of an intake restrictor
is required in some installation types.
The Riviera 42 requires the mandatory use of (p/n) 14 ½ x 14 ½ Wall Thimble in all installations where
vent pipe passes horizontally through any combustible construction.
Installation Considerations
Before installing any venting, proper assessment of venting system must be determined.
Unacceptable vent runs can affect the appliances combustion creating undesirable performance.
WARNING: This gas appliance must not be connected to a chimney flue serving a separate
solid-fuel burning appliance.
Venting Components
Side Wall Co-Axial termination without Nailing Flange
Side Wall Co-Axial termination with Nail Flange
Vertical Co-Axial Termination Simpson DuraVent Part Number
CFH DV Pipe to Duravent Adapter
Storm Collar
V58
RVF58
58DVA-VCH
AVT58
8SC
Rigid Direct Vent Co-Axial Pipe 12”
Rigid Direct Vent Co-Axial Pipe 24”
Rigid Direct Vent Co-Axial Pipe 36”
Rigid Direct Vent Co-Axial Pipe 48”
Vent Restrictor ( 3-hole 8” ring)
8RP1
8RP2
8RP3
8RP4
MBR42-3
Adjustable Roof Flashing 1-12 to 7/12 pitch
Adjustable Roof Flashing 8-12 to 12-12 pitch
Support Plate
Fire Stop
8AF
AFS
8SP
FS58
Rigid Direct Vent Co-Axial Pipe 90º Elbow
Rigid Direct Vent Co-Axial Pipe 45º Elbow
Rigid Direct Vent Co-Axial Pipe 60º Elbow
Rigid Direct Vent Co-Axial Pipe 30º Elbow
EL908
EL458
EL608
EL308
Aluminum Flex Direct Vent Co-Axial Pipe 12”
Aluminum Flex Direct Vent Co-Axial Pipe 24”
Aluminum Flex Direct Vent Co-Axial Pipe 36”
Aluminum Flex Direct Vent Co-Axial Pipe 48”
FP1
FP2
FP3
PF4
Bulk 2 ply Flex Direct Vent Pipe, 15’ roll
Bulk 2 ply Flex Direct Vent Pipe, 30’ roll
B5815
B5830
Bulk 2 ply Flex Direct Vent Pipe, 50’ roll
B5850
9
Vertical Venting Installations
Special Note for all Rigid Pipe Vent installations
Depending on the configuration starting at the rear of the fireplace either a 60° or 30° elbow will be required to
allow proper alignment of subsequent piping:
*60° required for horizontal direction first
*30° required for vertical direction first
• Up to four elbows (45º or 90º)
36 ft. max.
may be used
• Elbow combinations can be either
horizontal or vertical in any
combination that does not exceed
the four elbow limit.
• All venting configurations that fall
into the hatch area must have the 3
hole ring intake restrictor.
(See page ** for detail)
24 ft.
•For all vertical venting a Simpson
Duravent P/N 58VA-VCH
termination is required. When using
CFH rigid venting a ATV58 adapter
is needed.
3 hole intake
restrictor for
12 feet or
higher verticle
12 ft.
Use a roof flashing and
storm collar whenever passing
through the roof
Use a firestop whenever
passing through a ceiling
Use a support box
on exposed vent
0 ft
0 ft
20 ft.max
10
Horizontal Venting Installations
Special Note for all Rigid Pipe Vent installations
Depending on the configuration starting at the rear of the fireplace either a 60° or 30° elbow will be required to allow
proper alignment of subsequent piping:
*60° required for horizontal direction first
*30° required for vertical direction first
36 ft. max.
• Up to three elbows (45ºor 90º)
may be used.
• Elbow combinations can be either
horizontal or vertical in any
combination that does not exceed
the three elbow limit.
• All configurations in the hatch
area exceeding 12ft. vertical should
have the intake restrictor installed.
24ft
• NOTE: LP installations where
the horizontal will exceed 6 feet or
more must have a minimum 4 foot
rise.
• Shortest run is one foot vertical
and one foot horizontal or one 60º
elbow with short pipe to vent
termination.
• Vinyl or Plastic Exterior sidings
or soffit used in close proximity to
the Canadian Fire Hearth
Termination must use the optional
deflector supplied with each
RV58 termination kit
12 ft
6 ft.
0 ft
0 ft
20ft max.
When Applicable, the MBR42-3 Ring Restrictor
is installed into the intake portion of the CoAxial venting. The ring slides into the piping and
rest on the rolled bead manufactured in the pipe.
Note: If the restrictor is required it should be
installed before proceeding with further
connecting of the venting components.
Appliance Rear Vent
11
11
Minimum Vent Termination Clearances
Letter
A
B
C
D
E
F
G
H
CDN Installation
30cm
15cm
32cm*
32cm
US Installation
12”
6”
12.5” *
12.5
47cm*
32cm*
32cm*
91cm within a height of
4.5m above the
meter/regulator
assembly
18.5”*
12.5*
12.5*
3’ within a height of 15’
above the meter/regulator
assembly.*
I
J
91cm
30cm
3’*
9”
K
1.83m
L
2.13mt
3’ above if within 10’
horizontally.
7’*t
M
30cm +
12” +
Description
Clearance above grade, verandah, porch, deck, or balcony.
Clearance from window or door that may be opened.
Clearance from permanently closed window (to prevent condensation)
Vertical clearance to ventilated soffit located above the terminated
within a horizontal distance of 2 feet (60cm) from the center line of
terminal.
Clearance to unventilated soffit.
Clearance to outside corner.
Clearance to inside corner.
Clearance to each side of center line extended above meter/regulator
assembly.
Radial clearance around service regulator vent outlet.
Clearance to non-mechanical air supply inlet to building, or the
combustion air inlet to any other appliance.
Clearance to mechanical air supply inlet.
Clearance above paved sidewalk or paved driveway located on public
property.
Clearance under verandah, porch, deck, or balcony.
1 In accordance with the current CSA B149.1, Natural Gas and Propane Installation Code.
2 In accordance with the current ANSI 2223.1 NFPA 54, National Fuel Gas Code.
* These Numbers are only estimates. Clearances are in accordance with local installation codes and the requirements
of the gas supplier.
f A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single family
dwellings and it serves both dwellings.
+ Permitted only if verandah, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor.
NOTE: Venting terminals shall not be recessed into walls or siding.
12
Installation Planning
The recommended order of installation is as follows:
1 – Familiarize yourself with this manual.
2 – Check the minimum installation dimensions and vent installation.
3 – Check your local installation codes.
4 – Check you have the parts and components necessary to complete the installation.
5 – Check the gas and electrical supplies are ready.
6 – Prepare opening (remove any loose materials)
7 – Install Venting
8 – Install base unit and connect vent
9 – Connect gas and electrical supplies.
10 – Install operational components and prepared for first test fire
11 – Check to verify adequate accessibility clearance for service & proper operation
12 – Check operation of unit
13 – Take time to explain operation to customer (most call backs are caused by the customer not understanding the operation
of the unit.)
Existing Gas Supply
Before interrupting the existing gas supply it is recommended that the following be checked.
Shut down all gas appliances and carry out a pressure test to ensure there are no leaks in the system.
Before connecting the appliance to the gas supply line, double check that the appliance you have purchased is designed for the
gas type you are using. The gas type markings are located on the certification label and also on the appliance’s gas valve.
Check the gas pressure immediately upstream to ensure you will be able to supply the minimum inlet pressure for the
appliance.
Check your pipe sizing to ensure sufficient volume will be supplied to the appliance.
Gas Supply Installation
Provide adequate clearance for the proper installation and checking of the gas connection.
Have your gas supplier or a qualified gas fitter run a gas supply line into the gas fireplace. The line must be properly sized
and fitted according to the installation codes. Upstream of the appliance supply connection, the fitter shall provide an easily
accessible manual shut-off valve.
The gas supply pipe should enter the appliance case through the opening at the right side. The supply pipe should be
connected to the appliance gas inlet pipe situated at the right side of the control unit. Supply line connection to the inlet pipe
is 3/8 NPT.
Use only new black iron or steel pipes or copper tubing if acceptable – check local codes.
Note that in the USA copper tubing must be internally tinned for protection against sulfur compounds.
Unions in gas should be of ground joint type. Sealant used must be resistant to the action of all gas constituents including LP
gas. Sealant should be applied lightly to male threads to ensure excess sealant does not enter gas lines.
Pressure testing the supply line for leaks
The appliance and its individual shut-off valve must be disconnected from the gas supply piping system during any pressure
testing of the system at test pressures in excess of ½ psig (3.4kPa). The appliance must be isolated from the gas supply piping
system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test
pressures equal to or less than ½ psig (3.5kPa). Failure to do so will damage the appliance’s gas valve. Such damage is not
covered by the manufacturer’s warranty.
When testing for leaks:
Make sure that the appliance is turned off.
Open the manual shut-off valve.
Test for leaks by applying a liquid detergent or soap solution to all ball joints. Bubbles forming indicate a gas leak.
Correct any leak detected immediately.
Never use an open flame to check for leaks.
The pressure test point locations are built in to the regulator that controls the burner manifold pressure. The correct pressure
range is shown in the table in the specification section of this manual. The pressure check should be made with the burner lit.
See lighting instruction section for full operating details.
13
Placing and Securing Non-Combustible Panels
The Riviera 42 is shipped with five (5) separate panels of non-combustible panels which must be
installed with the appliance to conform with to certified safety standards. Two of the panels are
secured to the Cleanface from at the factory and require no special attention and are mentioned
only to avoid confusion. The large 42”x34.25” inch front panel utilizes the cutout for installation
under the appliance. The 14 ½ x 3 ½ must be installed at the top of the wall opening when
venting is routed horizontally from the rear of the appliance.
Metal panel brace
Plate for horizontal
Venting through
combustible wall
Non-combustible front panel
Cleanface Surround
Cut out from front panel must
be placed under appliance
before installation
14
Attaching the Cleanface Mounting Frame before Installation.
As noted previously, Gas and Electrical lines should be hooked to the appliance before attaching
Cleanface Surround and fitting Non-combustible front.
The Cleanface Front Assembly is fastened to the front of the Firebox unit by the self-tapping
sheet metal screws. (Fig 1)Before beginning take care to push up the left and right tabs for
supporting the cover grille to be installed on completion.
Figure 1
Figure 2
A Power drill with ¼ Hex Nut driver should be used to attach surround as shown in Figure 2. Prepunched holes are provided. Once the top has been secured locate the two pre-punched holes
located on the lower inside faces. Secure the sides to the appliance with tapping screws (Figure 3)
Next, secure the supplied metal wallboard brace onto the vertical framing on either side. The
brace height should be set so that it will adequately support the Non-combustible panel and the
drywall upon completion.
Figure 3
Figure 4
15
The brace should be fastened by either or screws to secure it in place. The Non-combustible
board can be fastened with standard drywall screws through the recessed holes provided when the
appliance is ready to close in
Figure 5
Figure 6
Install metal brace at 36” from bottom
of floor or base of elevation
16
Door Removal and Re-Installation Instructions
WARNING: Do not abuse the appliance’s glass by striking, slamming or similar trauma. Do not use the
appliance with the door removed, glass panel cracked or broken. Only use tempered glass approved for use
with this appliance. Do not use substitute materials. Replacement of the panel should only be carried out by a
licensed qualified service person
1) Remove the Control Valve Compartment cover grille which provides access to the door latch
mechanism
2) Door latch mechanisms located on the lower edge of the glass door are pulled forward then moved
down. The latch is spring loaded so sufficient effort is required to clear it from the door frame
before it will release.
3) Holding the bottom edge of the door frame tilt out the door assembly 4-5” then lift up to slide the
frame off the two retaining tabs located at the top of the Fire Box Enclosure
Picture of cover grille here
Window Re-Installation
To Re-install the Glass Door Assembly it is simply a reversal of the removal procedure. Hold the Door assembly at
about a 45° angle and line up the two top slots located on the frame top edge onto the two retaining tabs (shown in
illustration). Once in the grooves, the door should simply close down into place. If the assembly is not aligned well
some adjustment to the left or the right may be required to permit proper closure. DO NOT FORCE ASSEMBLY!
When Door assembly is aligned pull latch mechanism forward and up to secure door. Replace the Valve Compartment
Grille
17
Electrical Diagram
This appliance is equipped with a three pronged (grounding) plug for your protection against
shock hazard and should be plugged directly into a properly grounded three prong
receptacle. Do not cut or remove the grounding prong from this plug
L1(BK)
Fan Motor
Resistor Adjustable
Thermal disk (close on rise)
L2 (W)
G
Electrical Schematic
This appliance, when installed, must be
electrically grounded in accordance with
local codes or, in the absence of local
codes, with the National Electrical Code,
ANSI/NFPA 70, or the Canadian
Electrical Code, CSA C22.1.
CAUTION: Label all wires
prior to disconnection when
servicing controls.
Wiring errors can cause
improper and dangerous
operation.
VERIFY PROPER OPERATION
AFTER SERVICING
Optional Fan Kit
Each kit contains:
-Fan assembly with mounting
gasket
-Grounded electrical harness
-Rheostat & thermal switch
18
Lighting Instructions
For your safety, read the following before lighting:
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage
and personal injury or death
A. This appliance is equipped with an ignition device which
Automatically lights the pilot. Do Not try to light the pilot
by hand.
B. BEFORE LIGHTING smell all around the appliance area
For gas. Be sure to small next to the floor because some
gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMAELL GAS – Do not try to
Light the appliance – Do not touch any electric switch; do
not. Use any phone in your building – Immediately call your
gas supplier from a neighbour’s phone. Follow the gas
supplier’s instructions. – If you cannot reach your gas supplier,
call the fire department
C.
Use only your hand to push in or turn control knob.
Never use tools. If the knob will not push in or turn
by hand don’t try to repair it, call a qualified service
technician. Force or attempt repair may result in a
fire or explosion.
D.
Do not use this appliance if any part has been under
Water. Immediately call a qualified service
technician. To inspect the appliance and replace any
part which has been under water.
Operating Instructions
1.
STOP! Read the safety information above on
this label.
Set the thermostat to lowest setting or switch
to off
Turn off all electrical power to the appliance.
This appliance is equipped with an ignition
device which automatically lights the pilot.
Do not try to light the pilot by hand.
Remove control access cover
Identify that the module control switches are
set to the desired operation. Check if the
electronic module is powered by back up
batteries and/or AC adapter. The back up
batteries will light the appliance even if the
AC power has been turned off.
2.
3.
4.
5.
6.
7.
Wait five minutes to clear out any gas. Then
smell for gas, including near the floor. If you
smell gas, STOP! Follow “B” in the safety
information on this label. If you don’t smell gas
go on to the next step.
8. Turn up thermostat or turn on power switch –
sufficient time must be allowed for air to escape
from lines if the unit is being lit for the first
time.
9. Replace control access cover.
10. Turn on all electric power to the appliance.
11. Set thermostat to desired setting.
12. If the appliance will not operate, follow the
instructions “To Turn Off Gas To Appliance”
and call your service technician or gas supplier.
To Turn Off Gas to Appliance
1.
2.
3.
Set the thermostat to lowest setting or
on/off switch to off.
Turn off all electrical power to the
appliance
Remove control access.
4.
5.
Remove backup batteries if service is to be
performed or for extended shutdown.
Replace control access.
19
Final Checks
Installer: Before leaving the appliance with the customer, you
must check the operation of the appliance.
*Check correct rating by clocking the appliance at 15 minutes.
(See label)
*Check flame description as seen on page 14. Adjust primary air
if required.
*Take time to go through the unit with the customer.
Note: When first fired, the unit will produce an odour. This is
normal and is part of the paint curing process. It is recommended
that you open a few windows to ventilate the room. This will be
noticeable for at least 4 hours. During the first hour, smoke
detectors in the house may be set off.
*Following the initial burn-in period, the glass panel may require
cleaning.
Caution: Do not clean the glass when the appliance
is hot!
*When the appliance is fired from cold, the glass may fog up.
This is due to condensation and is normal.
*Make yourself familiar with these instructions before operating
the appliance.
*Check any loose electrical wires that may cause a shock.
*Check all around the appliance for gas leaks. If you smell gas,
follow the instructions on the front cover of this manual.
*Check to see that logs are correctly positioned. The pilot light
should be visible.
*Check to make sure that venting is secure.
*Check all external parts, such as grills, doors and control covers
to make sure they are attached and fastened properly.
Caution: Do not turn the unit off and on again without
a minimum of a 60 second wait.
*The appliance area must be kept clear & free from combustible
materials, gasoline, and other flammable vapors or liquids.
Log set & burner require no maintenance.
Important – Glass Cleaning – Mineral Deposits
One of the by-products of the combustion process in a gas
appliance is a mineral which can show up as a white film on the
ceramic glass of the viewing door. The composition of the
deposit varies widely from various locations and also from the
time in the same location. You may have the problem for a time
and then not see it again for months when it will reappear in your
area. It seems this is associated with the varying sulfur content of
the gas. Ceramic glass manufacturers cannot give us a definitive
answer to this problem. Dealers may provide various cleaning
products with varying results. The following recommendations
will not guarantee results in your particular case.
Note: This is a problem beyond CFHMfg’s control and is not
covered under warranty.
1.
Clean the glass regularly as soon as you notice
the buildup, (white film). If the film is left for a
longer period of time, build up will bake on.
Once baked, it is much harder, if not
impossible, to remove.
2.
Never use an abrasive cleaner on the
glass. Any abrasion of the surface has the
3.
4.
immediate effect of lessening the strength of the
glass. An emulsion type cleaner is
recommended.
Use a soft damp cloth to apply the cleaner. Dry
the glass with a soft dry and preferably cotton
cloth. Most paper towels and synthetic
materials are abrasive to ceramic glass and
should be avoided.
Our dealers have had good results from the
products listed below. We cannot however
guarantee the results of these products.
A) Brasso
B) Polish Plus by Kel Kem
C) Cook Top Clean Crème by Elco
D) White Off by Rutland
Cold Weather Operation
When using any gas appliance (LP or NG Fuels) water is a
byproduct of the combustion process. Under normal conditions,
this is expelled through the vent into the atmosphere and does not
cause any harm. In extremes of cold weather however, the vapors
may condense and freeze on any exposed surface it comes into
contact with. This can cause a problem by restricting or blocking
the vent, particularly with direct vent wall terminations as the
exhaust is only a few inches away from the outside wall surface.
What happens to the moisture after it leaves the vent cannot be
controlled by the manufacturer. To extend the vent further out
from the wall can sometimes be an advantage. Extending the vent
out from the wall can present other design problems such as ice
falling from the eaves above. It is the home owner’s
responsibility to ensure that there is not an excessive build-up of
ice on the termination.
Caution: When operating your appliance during
cold weather, you must frequently check the
exhaust cap for excessive ice build-up.
Operating Your Fire
The operating instructions are also on a chained plate inside the
control access door. For your safety, this appliance is fitted with a
flame supervision device which will shut off the gas supply if for
any reason, the pilot flame goes out. This device incorporates a
fixed probe, which senses the heat from the pilot flame. If the
probe is cool, the device will prevent any gas flow unless the
burner control knob is kept pushed in at the “PILOT” position.
When first turned on, the decorative flames will appear
predominantly blue. After approximately 15 minutes, the flames
will turn yellow.
20
Thermostat Installation
Thermostat or wall switch installation
The burner control switch is located in the centre of the control department opening. For your convenience, the
unit can also be operated by a thermostat or a wall switch control. Electronic are available from any authorized
CFHMfg dealer. Please note, bedroom installations require the use of a wall thermostat. Mount the thermostat or
switch in the desired location and run “two conductor thermostat wires” to the heater’s lower right hand corner,
close to the gas supply line.
Note: The thermostat or wall switch MUST be rated for electronic
Minimize splicing in all wiring and solder all unavoidable splices.
Thermostat Wire Information
AWG
22
20
18
16
14
mm
0.6
0.8
1.0
1.3
1.6
ft.
10
25
40
64
100
m
3.0
7.6
12.2
19.5
30.5
Wireless Remote Control Option
The Riviera 42 Electronic Valve system utilizes and Remote Ready Control Module. No
additional components need to be installed. The module is simply switched to remote operation
and the handheld remote if fully functional. Remote Part Number is FP1001TH
Pilot Check: The Riviera 42 utilizes an electronic pilot which only operates when the unit is
activated. Pilot flame should adequately cover the spark and flame electrodes as shown in the
Illustration above
WARNING: Incorrect adjustment of flame can lead to improper combustion which can be a safety hazard.
21
Flame Quality Adjustment
Adjustment Prodedure.
Air / Fuel mixture is adjusted at the burner tube.
Access to this feature is done through the top of the burner cover by removing the two fasteners from the
rectangular metal cover. Once the screws have been remove lift off the metal cover plate.
Rotating Air/Fuel Mixture Sleeve
A rotating sleeve located at the fuel entry of the burner tube directly after the gas orifice.. Once an adjustment has
been made the cover must be replaced and the unit re-started to evaluate the change. Please allow unit to reach
normal operating temperatures to properly determine final flame quality.
Flame Types
1. Blue at the base and
light orange above.
Medium height (ideal)
2. Mostly blue with little
or no orange. Short
height (too much air)
3. Mostly yellow with
little or no blue. Long
stringy flame (no air)
May result in carbon
deposits on logs & glass
Adjustment
None
Close damper
Open damper
WARNING: Incorrect adjustment of flame can lead to improper combustion which can be a safety hazard.
22
Replacement Parts List
BURNER COMPONENTS
Burner Tube
Glass Door (Robax panel in frame)
Pilot Assy. (NG)
Riviera 42 Valve Tray
Valve tray Gasket
Gas Valve American Flame Electronic 4000 (NG)
CFH Electronic Pilot Assembly
LP Pilot Orifice (Danna Controls)
Main Burner Orifice (Liquid Propane)
Main Burner Orifice (Natural Gas)
CDC006PT
RGD42RIV
DC006NG
Riv 42 Gas Tray
GK01
GC1001
DC006E
LPPO
MB042LP
MBO42NG
NON-COMBUSTABILE COMPONENTS
Front Panel 43”X 34 ¼”w/ Base Panel (for under Riviera 42) FB001
Through wall Panel 14 ¼” X 3 ½””
FB002
DECORATIVE PARTS
Replacement Cement Board for CFLKRIV42
Touch up Aerosol Paint (Hi-temp Flat Black)
CFLK42NCB
1A51H200A116A1
FAN PARTS
12 inch Fan Only
Speed Control Only
Fan Thermoswitch
Wiring Harness, Complete
Power Junction Box
DCFK12
VEC25
FL120
WH001
BJB01
23
For maintenance, proper re-assembly and resealing of the venting system is required.
Valve Tray Assembly Removal
-Remove door assembly
-Remove any decorative materials ( glass beads, chips, etc.)
-Remove the Burner Cover fasteners and remove burner cover trays
-Remove burner tube by unfastening the two hold down screws and lifting it out.
-Disconnect gas supply
-Disconnect all electrical leads (label leads prior to removal)
-Remove the screws that hold the valve plate assembly
-Carefully lift out the assembly
Venting System
The appliance should be inspected before use and at least annually by a professional
service person.
More frequent cleaning may be required due to excessive lint from carpet bedding material etc. It
is imperative that control compartment, covers of the appliance to be kept clean.
24
Conditions and Limitations of Warranty
CFHMfg warrants its products against manufacturing defects to the original purchaser only – i.e., the individual or legal entity
(registered customer) whose name appears on the warranty registration card filed with CFHMfg – provided that the purchase was
made through an authorized CFHMfg dealer and is subject to the following terms and limitations:
This factory warranty is nontransferable and may not be extended whatsoever by any of our representatives.
The gas fireplace or fireplace insert must be installed by a licensed, authorized service technician, or contractor. Installation must
be done in accordance with the installation instructions included with the product and all local and national building and fire
codes.
This limited warranty does not cover damage caused by misuse, lack of maintenance, accident, alterations, abuse, or neglect, and
parts installed from other manufacturers will nullify this warranty.
This limited warranty further does not cover any scratches, dents, corrosion, or discolouring caused by excessive heat, abrasive
and chemical cleaners, nor breakage of logs and embers, nor any venting components used in the installation of the fireplace.
CFHMfg warrants its steel burners against defects in workmanship and material for life, subject to the following conditions:
During the first 10 years, CFHMfg will replace or repair the defective parts at our option free of charge. From 10 years to life,
CFHMfg will provide replacement burners at 50% of the current retail price.
In the first year only, this warranty extends to the repair or replacement of warranted parts which are defective in material or
workmanship provided that the product has been operated in accordance with the operation instructions and under normal
conditions.
After the first year, with respect to the Luxor Limited Lifetime Warranty, CFHMfg may, at its discretion, fully discharge all
obligations with respect to this warranty by refunding to the original warranted purchaser the wholesale price of any warranted but
defective part(s).
After the first year, CFHMfg will not be responsible for installation, labour, or any other costs or expenses related to the
reinstallation of a warranted part, and such expenses are not covered by this warranty.
Notwithstanding any provisions contained in this Luxor Limited Lifetime Warranty, CFHMfg’s responsibility under this warranty
is defined as above and it shall not in any event extended to any incidental, consequential, or indirect damages.
This warranty defines the obligation and liability of CFHMfg with respect to the Luxor gas appliance and any other warranties
expressed or implied with respect to this product, its components, or accessories are excluded.
CFHMfg neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of
this product. CFHMfg will not be responsible for: over-firing, downdrafts, spillage caused by environmental conditions such as
rooftops, buildings, nearby trees, hills, mountains, inadequate vents, or ventilation, excessive venting configurations, insufficient
makeup air, or negative air pressure which may or may not be caused by mechanical systems such as exhaust fans, furnaces,
clothes dryers, etc.
Any damages to fireplace, combustion chamber, or other components due to water, weather, longs periods of dampness,
condensation, chemicals, or cleaners, will not be the responsibility of CFHMfg.
The bill of sale or copy will be required together with a serial number and a model number when making any warranty claims
from your authorized dealer. The warranty registration card MUST be returned within fourteen days of purchase to register the
warranty.
CFHMfg reserves the right to have its representative inspect any product or part thereof prior to honouring any warranty claim.
25
Download PDF

advertising