Operating instructions
Directly coupled
screw compressors
Series
C 3 L...C 7 L
C 3 LR...C 7 LR
C 3 LDR...C 7 LDR
Separate manuals:
Compressor control
Refrigeration compressed air dryer (C LDR)
Operating instructions
for directly coupled
screw compressors
–
–
–
–
C 3 L / C 3 LR / C 3 LDR
C 4 L / C 4 LR / C 4 LDR
C 5 L / C 5 LR / C 5 LDR
C 7 L / C 7 LR / C 7 LDR
(2.2 kW)
(3.0 kW)
(4.0 kW)
(5.5 kW)
BOGE KOMPRESSOREN
Postfach 10 07 13
33507 Bielefeld
Otto-Boge-Straße 1-7
33739 Bielefeld
Phone:
Fax:
Mail:
Net:
+49 5206 601-0
+49 5206 601-200
info@boge.com
www.boge.com
Issue: 05 / 2011
No. 596.1144.01
Nominal price: € 5.00
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page I
Index
Index
Part 1:
General
Part 2:
Product description
1.1
General safety instructions ...........................................................
Safety instructions for compressor operation ...................................
Special hazard warnings...................................................................
Electrical energy hazards .................................................................
Obligations of the owner ...................................................................
Personnel requirements....................................................................
Personal protective equipment .........................................................
Safety instructions for maintenance and repair of the compressor...
Accident prevention regulations........................................................
1.2
Introduction..................................................................................... 6
Symbols used ................................................................................... 7
Symbols on the compressor ............................................................. 8
Intended use ..................................................................................... 9
Foreseeable Misuse ......................................................................... 9
Transport damage ............................................................................ 9
Data on the type plate..................................................................... 10
Service............................................................................................ 10
2.1
Technical data............................................................................... 11
2.2
Function description ....................................................................
Function principle of the air end......................................................
Air circuit .........................................................................................
Oil circuit .........................................................................................
14
14
15
16
2.3
Compressor control .....................................................................
Network pressure............................................................................
Operating states .............................................................................
Operating modes ............................................................................
Short operating times......................................................................
17
17
17
17
18
2.4
Control devices............................................................................. 18
Operating pressure transmitter ....................................................... 18
2.5
Safety and monitoring devices....................................................
General ...........................................................................................
Safety valve ....................................................................................
Safety temperature limiting device..................................................
Monitoring the drive motor ..............................................................
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
1
1
2
3
3
4
4
4
5
18
18
19
19
19
Page III
Index
Part 3:
Installation
3.1
Transport and storage..................................................................
General ...........................................................................................
Transport possibilities .....................................................................
Intermediate storage .......................................................................
21
21
21
22
3.2
Compressor room.........................................................................
Installation, maintenance conditions and application for
compressed air receivers arranged below or separately ................
Installation surface ..........................................................................
Fire protection .................................................................................
Sound protection.............................................................................
Admissible environmental influences..............................................
Ventilation .......................................................................................
Cooling air requirement ..................................................................
Condensate disposal ......................................................................
23
23
23
23
24
24
24
25
25
3.3
Installation.....................................................................................
General ...........................................................................................
Checking the delivery scope ...........................................................
Installing the compressor ................................................................
Connecting the compressor to the compressed air network...........
Checking the oil level......................................................................
26
26
26
26
27
27
3.4
Electrical connection.................................................................... 27
3.5
Commissioning.............................................................................
Check installation requirements......................................................
Checking the rotational direction ....................................................
Check compressed air outlet for tightness......................................
Opening the stop valves .................................................................
Checking for leaks ..........................................................................
Conduct trial run .............................................................................
Commissioning following extended stoppages ...............................
Refrigeration compressed air dryer ................................................
3.6
Dismantling ................................................................................... 32
Part 4:
Faults
4.1
General .......................................................................................... 33
4.2
General faults ................................................................................ 33
Part 5:
Maintenance
5.1
Safety instructions ....................................................................... 35
5.2
General ..........................................................................................
Maintenance through BOGE customer service ..............................
Review of regular maintenance work..............................................
Maintenance intervals .....................................................................
Page IV
28
29
29
29
30
30
30
31
31
37
37
37
38
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Index
5.3
Part 6:
Appendix
General information concerning the lubricants used ......................
Disposal of used operating material ...............................................
Pressure hoses...............................................................................
Spare and wearing parts.................................................................
40
41
41
41
Regular maintenance work ..........................................................
Draining off the condensate from the compressed air receiver ......
Draining off the condensate from the compressed air receiver
with automatic condensate separator .............................................
Clean or change suction filter .........................................................
Cleaning the filter cartridge.............................................................
Drive motors with permanent lubrication ........................................
Checking the oil level, topping up oil ..............................................
Changing the oil filter ......................................................................
Changing the oil separator..............................................................
Oil change.......................................................................................
Flushing the oil circuit .....................................................................
Cleaning the compressed air/oil cooling unit ..................................
Checking the safety valve...............................................................
42
42
43
43
44
44
45
46
47
48
50
51
52
5.4
Spare parts and optional equipment .......................................... 53
List of spare and wearing parts (for maintenance) ......................... 53
List of available optional equipment................................................ 53
6.1
Flow chart...................................................................................... 55
Air cooled version, standard ........................................................... 56
6.2
List of maintenance and service work........................................ 58
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page V
General
Part 1: General
1.1
General safety instructions
1.1 General safety instructions
Caution!
Nonobservance of the following safety instructions may lead to injuries and
damage to the compressor.
Also observe the generally valid safety and accident prevention regulations
in addition to the information in these operating instructions!
Safety instructions for
compressor operation
1. Ensure that no commissioning and maintenance work on the compressor
is undertaken until these operating instructions are understood.
2. Only use the compressor for its intended use, as described in these
operating instructions.
3. The owner must ensure:
– that only appropriately trained and authorized personnel work on this
compressor,
–
that no persons work on this compressor, whose ability to react is
restricted due to misuse of e.g. drugs, alcohol, medication etc.,
–
that the operating, maintenance and repair personnel has been made
fully familiar with all safety instructions, and that they are being
observed,
–
that the compressor is only operated in a safe operating condition.
4. Avoid any operating method which may impair the safety of the compressor.
5. Always wear your compulsory personal protective quipment as a protection against injuries from sharp corners or edges when working on the
compressor.
6. To avoid dangers from debris or parts lying around, the service area of the
compressor has always to be kept tiedied up and clean.
7. Always squat when working on components mounted at low height, never
stoop. When working on components mounted higher up always stand
upright and erect.
8. Do not exceed the limit value for the final compression pressure specified
on the type plate.
9. Do not operate the compressor without the attendant protection and safety
devices.
Do not dismantle any built-in safety devices or put them out of operation.
Ensure that all safety claddings and doors are closed prior to commissioning/starting up the compressor and that they are not opened during operation.
10. Place the compressor out of operation as described in these operating
instructions, when dismantling the safety claddings or safety devices for
repair or maintenance work. Reattach and close all cladding and safety
devices immediately upon completion of the repair or maintenance work.
11. Only operate the compressor using the additional equipment (options) recommended or authorized by the manufacturer.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 1
General
1.1
General safety instructions
12. Undertake conversions and modifications of the compressor only with
BOGE prior approval, taking all relevant safety regulations into consideration. The manufacturer is not liable for damages resulting from independent modifications on the compressor.
13. Never start the compressor when one or several parts (e.g. cable, plug)
are damaged, when not in perfect working order and when damage is
detected or suspected.
14. Observe all safety and danger signs directly attached on the compressor!
Special hazard warnings
–
Always wear your compulsory personal protective equipment when working on pressure pipes and connections!
–
A protective grid serves to prevent you from accidentally reaching into the
impeller of the cooling fan.
Caution: Risk of injury!
A protective grid serves to prevent you from accidentally reaching into the
impeller of the cooling fan!
Please note that the cooling fan may run on for a certain time even after the
compressor has been switched off!
–
During operation, the compressor generates a high sound pressure level
which may cause permanent hearing damage due to continuous noise
stress. As a rule, the compressor may only be operated with its housing
cover closed. Make sure to additionally wear a hearing protection in case
of a noise pressure level above 80 dB(A)!
–
A rigidly screwed-down protective cover prevents you from accidentally
reaching into the drive coupling during operation of the compressor.
Caution: Risk of injury!
Never operate the compressor with dismantled coupling protection. There is
a risk that you reach into the fast rotating coupling!
Any servicing on the coupling may only be carried out during standstill of the
compressor!
–
Page 2
The pressure relief valves as well as the intake and exhaust opening on
the suction filter are mounted at the back in order to prevent the compressed air exhaust jet from pointing toward the operator.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
General
1.1
General safety instructions
Electrical energy
hazards
Warning: Voltage!
There is danger of life when working on the electrical equipment of the
compressor!
Obligations of the owner
–
Disconnect mains connection prior to starting to carry out works on the
compressor and use padlock to secure against switching on again.
–
Only duly authorized professional electricians (e.g. plant electricians) are
allowed to carry out works in the electrical area of the machine.
–
Make sure to check the electrical equipment of the compressor at regular
intervals for defects such as loose connections or scorched cables and
have any defects repaired immediately.
–
Make sure to have all electrical equipment and fixed electrical installations checked by a professional electrician at least every 4 years.
–
Any modifications that may have been carried out after examination must
conform to DIN EN 60204-1:2007.
–
Make sure to check all safety installations on the machine for proper functioning at regular intervals.
–
Only use original fuses.
The owner is obliged to,
–
operate the compressor only in technically perfect condition,
–
check the Emergency Stop device of the compressor regularly for completeness and functionality,
–
assess the hazards of the machine working places in his area of responsibility and to issue the ensuing operating instructions,
–
to name a person responsible beeing in charge of the safe operation of the
machine as well as the coordination of all service work performed on it,
–
avoid stress situations while operating the compressor by means of technological and organizational operation scheduling,
–
ensure a proper workplace lighting at the compressor control section according to the local health and safety regulations,
–
observe the safety data sheet of the used lubricants and to customize the
personnel all information as to said data sheet,
–
provide the compulsory personal protective equipment and to stipulate
and check the wearing of said protective equipment on a regular basis,
–
assign the personnel responsible for various tasks and work on the machine,
–
instruct the personnel on a regular basis with respect to all obligations as
to compressor related preservation of safety and tidiness.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 3
General
Personnel requirements
1.1
General safety instructions
Work on and with the compressor may only be carried out by personnel duly
authorized by the owner of the compressor.
The personnel working on the compressor has to observe all industrial safety
regulations and operating instructions, properly recognize responsibilities and
read and understand the operating instructions. It is essential to wear the compulsory personal protective equipment when working on the compressor!
Personal protective
equipment
In general for all work on the compressor
–
protective clothing,
–
chemicals resistant gloves,
–
slip-resistant safety shoes and
–
hearing protection, if applicable,
are compulsory.
For special duties
–
protective helmets (for transport work with lifting gear) and
–
safety goggles (when working on the compressed air system, on the control pneumatics and/or on the cooling system of the built-in dryer)
must be worn.
Before starting work using oils or greases a skin protection cream must be
applied. Having finished the work a skin care product must be applied.
Safety instructions for
maintenance and repair
of the compressor
Caution!
Only use original spare parts, compressor oils and operating materials released by BOGE during repair or maintenance!
Warning: Voltage!
When working on the electrical system there is a constant danger of getting
into contact with live parts!
To avoid such dangers the mains connection must be equipped with a disconnecting device!
The mains disconnecting device has to meet the requirements of DIN EN
60204-1:2007!
1. Ensure that maintenance work is only carried out by appropriately trained
persons.
2. Ensure that setting work, malfunction rectification and repair is only carried
out by specialists or appropriately trained persons.
Page 4
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
General
1.1
General safety instructions
3. Prior to maintenance or repair work:
– Press Emergency Stop button.
–
Open mains disconnecting device.
–
Secure mains disconnecting device against unintentional switching on
by means of a padlock.
–
Fix a warning label to the control and fill in the name of the person responsible who is authorized to switch on the maschine again.
–
Check to ensure that all parts are currentless.
–
Disconnect the compressor from the compressed air network (relieve
or block pressurized lines).
4. Exercise extreme caution during repair or maintenance work requiring the
compressor to be operational.
Ensure that persons keep out of reach of the hazardous area.
5. Ensure that work on the electrical equipment is only executed by qualified
electricians.
6. Work on parts and devices under current is prohibited. Exceptions are
governed by the appropriate regulations, e.g. DIN VDE 0105.
7. Prior to starting work on the electrical system the power supply has to be
switched off and secured against unintentional switching on again. Immediately after having finished the work all dismantled claddings and safety
devices must be refitted.
8. The operator is responsible to check the compressor daily for externally
visible damage and defects, and to immediately report any changes
(including operational behaviour).
9. When the automatic restart (Auto-Restart) is activated, the compressor will
start automatically following a voltage loss. Prerequisite: The net pressure
is lower than the set switch-on pressure.
Accident prevention
regulations
The owner of a compressor plant is responsible to ensure that it is properly
installed, operated and maintained.
Prior to commissioning, owners in the Federal Republic of Germany urgently
have to read the currently valid regulations of the Main Association of the
Industrial Employers' Liability Insurance. Apart from other regulations particularly the Ordinance on Industrial Safety and Health (BetrSichV) is applicable.
The regulations are available at the following locations:
Berufsgenossenschaft (Industrial Employers' Liability Insurance)
Carl-Heymanns-Verlag KG, Luxemburger Straße 449, D-50939 Köln
Beuth Verlag GmbH, Burggrafenstraße 6, D-10787 Berlin
For operation of the compressor plant outside the Federal Republic of Germany, the accident prevention regulations of the country, where the compressor is operated, must be observed in addition to the data contained in these
operating instructions.
In the event that measures are required above and beyond the legal regulations specified in the Federal Republic of Germany or the data contained in
these operating instructions, then it is of utmost importance that these be carried out prior to commissioning the compressor plant.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 5
General
1.2
Introduction
1.2 Introduction
The purpose of these operating instructions is to familiarize the user with the
function and all application possibilities of the compressor.
These operating instructions contain important information on how to operate
the compressor safely, economically and according to its intented use. Observing these operating instructions will assist in avoiding danger, to reduce
repair costs and down times and to increase the reliability and service life of
the compressor. It contains important information concerning the required
maintenance and repair measures, assists in case of malfunctions and contains data concerning spare and wearing parts.
The operating instructions must be available to the compressor operating personnel at the place of operation, at all times.
The operating instructions must be carefully read and applied by all persons
engaged to undertake the following work on the compressor:
–
Operation, including fault rectification and daily care
–
Maintenance (service, inspection, repair)
–
Commissioning
–
Transport
The compressor and its additional equipment must not be installed and commissioned until the operating instructions are understood.
These operating instructions can be supplemented with instructions on the
basis of existing national regulations concerning accident prevention and environmental protection.
In the illustrations, the compressor is shown in part without safety cladding or
safety devices for better visualization. However, operation without these components is prohibited!
Page 6
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
General
Symbols used
1.2
Introduction
In these operating instructions the most important safety notes and tips are
especially characterized by the following symbols:
Caution: Risk of injury!
This symbol indicates information warning of possible danger to life and limb
of the operator or other persons.
Attention!
This symbol indicates information warning of dangers to life and limb of the
operator or other persons or dangers, which might destroy or damage the
compressor.
Warning: Voltage!
This symbol indicates information warning of life threatening electrical voltage levels.
It indicates work which must be exclusively performed by skilled electricians.
Note!
This symbol indicates information and tips concerning the economical and
careful operation of the compressor.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 7
General
1.2
Introduction
Symbols on the
compressor
Note!
All warning signs on the compressor and in its surrounding must always be
kept in a legible condition. Missing or damaged signs must be replaced at
once!
The following symbols and warning signs are fitted on the compressor:
Warning!
Hot surfaces: Do not touch!
Warning!
The unit is operated by remote control, and might start without warning.
Note!
Instructions for the operating personnel must be read.
Prohibited!
Never open the valve before the air hose (connection to the compressed air
network) is connected.
Page 8
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
General
1.2
Introduction
Intended use
Caution!
BOGE compressors, including their additional equipment, are exclusively
intended for the compression of air. The air taken in must not contain any
explosive or chemically instable gases or vapours.
Do not exceed the specified final compression temperature.
BOGE compressors are designed for stationary operation.
Ensure that they are only installed and operated in dry and clean rooms.
Operation and control are designed to be executed by trained and authorized
operators.
Foreseeable Misuse
Caution!
Never direct the produced compressed air towards persons.
Danger to life!
Oil is injected into the pressure rooms of the compressor.
Only use the produced compressed air for breathing or let it come in contact
with foods, if it was treated beforehand.
This BOGE compressor is not explosion protected.
Do not operate in explosive areas or in a possibly explosive atmosphere!
Do not operate the compressor in rooms in which extreme dust, toxic or flammable vapours and gases may occur.
The following is not permitted:
–
Transport damage
Compression of other media than those mentioned under intended use
or compression of air loaded with contaminants.
–
Exceeding the final compression pressure indicated on the type plate.
–
Altering the safety devices and safety cladding or placing them out of
operation.
–
Removing or painting over signs and symbols on the compressor.
–
Operation of the compressor by unauthorized or untrained persons.
BOGE does not accept any liability for breakage or transport damage. Please
inspect the compressor immediately after delivery and direct damage claims
to the last haulier – even when the packing is not damaged!
To safeguard claims against the haulier we recommend leaving the machine,
devices and packing material in the same condition as they were in when the
damage was detected.
In the event of any other complaints, please inform us within six days after
arrival of the delivery.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 9
General
Data on the type plate
1.2
Introduction
Enter the data of your compressor from the type plate or enclosed data sheet
in the illustration below. This will ensure that in the event of enquiries, you will
always have the most important data to hand.
Type
Year of construction
Serial number
F.a.d.
max.
Final compression pressure
Motor speed
Motor power
m3/min
bar
min–1
kW
Otto-Boge-Straße 1– 7 · D-33739 Bielefeld · Telefon (0 52 06) 6 01-0
Postfach 10 0713 · D-33507 Bielefeld · Fax (0 52 06) 6 01-2 00
www.boge.com · info@boge.com
Fig. 1.1: Data on the type plate
Service
Please do not hesitate to contact BOGE service if you have any questions.
Please call:
Telephone: +49 5206 601-140
In the event of inquiries, always specify the following data of your compressor
to prevent any delays:
–
Type
–
Year of manufacture
–
Machine number
Attention!
Only BOGE service technicians or persons authorized by BOGE in writing
may repair or alter the compressor during the warranty period. Otherwise all
warranty claims will expire!
Page 10
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Product description
2.1
Part 2: Product description
Technical data
2.1 Technical data
Technical data for C 3 L...C 7 L Compressor assembly, part 1
Type
C3L
C4L
C5L
C7L
Dimensions
– Width
[mm]
755
755
755
755
– Depth
[mm]
485
485
485
485
– Height
[mm]
492
492
492
492
– silenced
[kg]
105
110
125
130
– super silenced
[kg]
–
–
–
–
[dB(A)]
61
62
67
68
[dB(A)]
13
13
13
13
[dB(A)]
74
75
80
81
[°C]
110
110
110
110
Weight
Max. sound pressure level
[±3 dB(A)]
accord. to DIN 45635, part 13
– silenced / super silenced
Reference surface measure
– silenced / super silenced
Sound power level
– silenced / super silenced
Compressor
max. final compression temperature
Volume flow according to
ISO 1217 appendix C at:
8 bar
[m3/min]
–
–
–
–
– pmax = 10 bar
[m3/min]
0.240
0.340
0.545
0.728
– pmax = 13 bar
[m3/min]
–
0.234
–
0.525
2.2
3.0
4.0
5.5
– pmax =
Drive motor
Rated power
[kW]
Nominal speed
[min–1]
– 50 Hz
Protection type
Design
1500
1500
3000
3000
IP
55
55
55
55
IMB
35
35
35
35
F
F
F
F
ISO class
Electrical connection
Mains voltage 1)
Frequency 1)
Min. fuse protection
2) 3)
Recommended fuse protection
1)
2)
3)
2) 3)
[V]
230/400
400
400
400
[Hz]
50/50
50
50
50
[A]
16/10
16
16
20
[A]
16/16
20
25
25
Standard equipment. Mains voltages and frequencies are specified on a plate in the switch cabinet.
Only for 400 V / 50 Hz. The fuse values change in the case of other mains voltages and frequencies.
Use fuse gL – gG or circuit-breaker with C-characteristic only.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 11
Product description
2.1
Technical data
Technical data for C 3 LR...C 7 LR Compressed air system, 90-litre-receiver, 10 bar, part 1
C 3 LDR...C 7 LDR Compressed air centre, 270-litre-receiver, 10 bar, part 1
Type
C 3 LR
C 4 LR
C 5 LR
C 7 LR
C 3 LDR
C 4 LDR
C 5 LDR
C 7 LDR
Dimensions
– Width
[mm]
1185
1185
1185
1185
1725
1725
1725
1725
– Depth
[mm]
550
550
550
550
675
675
675
675
– Height
[mm]
965
965
965
965
1165
1165
1165
1165
[l]
90
90
90
90
270
270
270
270
– silenced
[kg]
175
180
195
200
245
250
265
270
– super silenced
[kg]
–
–
–
–
–
–
–
–
[dB(A)]
61
62
67
68
61
62
67
68
[dB(A)]
13
13
13
13
13
13
13
13
[dB(A)]
74
75
80
81
74
75
80
81
[°C]
110
110
110
110
110
110
110
110
Receiver volume
Weight
Max. sound pressure level
[±3 dB(A)]
accord. to DIN 45635, part 13
– silenced / super silenced
Reference surface measure
– silenced / super silenced
Sound power level
– silenced / super silenced
Compressor
max. final compression temperature
Volume flow according to
ISO 1217 appendix C at:
– pmax =
[m3/min]
8 bar
– pmax = 10 bar
–
–
–
–
–
–
–
–
3
0.240
0.340
0.545
0.728
0.240
0.340
0.545
0.728
3
–
–
–
–
–
–
–
–
[m /min]
– pmax = 13 bar
[m /min]
Drive motor
Rated power
[kW]
2.2
3.0
4.0
5.5
2.2
3.0
4.0
5.5
Electrical power intake dryer
[kW]
–
–
–
–
0.19
0.21
0.21
0.28
Nominal speed
[min–1]
– 50 Hz
Protection type
Design
1500
1500
3000
3000
1500
1500
3000
3000
IP
55
55
55
55
55
55
55
55
IMB
35
35
35
35
35
35
35
35
F
F
F
F
F
F
F
F
230/400
400
400
400
230/400
400
400
400
ISO class
Electrical connection
Mains voltage compressor 1)
Mains voltage dryer
[V]
1)
Frequency 1)
Min. fuse protection
2) 3)
Recommended fuse protection
1)
2)
3)
2) 3)
[V]
230
–
–
–
230
230
230
230
[Hz]
50/50
50
50
50
50/50
50
50
50
[A]
16/10
16
20
20
16/10
16
20
20
[A]
16/16
20
25
25
16/16
20
25
25
Standard equipment. Mains voltages and frequencies are specified on a plate in the switch cabinet.
Only for 400 V / 50 Hz. The fuse values change in the case of other mains voltages and frequencies.
Use fuse gL – gG or circuit-breaker with C-characteristic only.
Page 12
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Product description
2.1
Technical data
Technical data for C 4 LR, C 7 LR Compressed air system, 160-litre-receiver, 13 bar, part 1
C 4 LDR, C 7 LDR Compressed air centre, 350-litre-receiver, 13 bar, part 1
Type
C 4 LR
C 7 LR
C 4 LDR
C 7 LDR
Dimensions
– Width
[mm]
1445
1445
1755
1755
– Depth
[mm]
550
550
720
720
– Height
[mm]
1080
1080
1215
1215
[l]
160
160
350
350
– silenced
[kg]
230
250
300
320
– super silenced
[kg]
–
–
–
–
[dB(A)]
62
68
62
68
[dB(A)]
13
13
13
13
[dB(A)]
75
81
75
81
[°C]
110
110
110
110
Receiver volume
Weight
Max. sound pressure level
[±3 dB(A)]
accord. to DIN 45635, part 13
– silenced / super silenced
Reference surface measure
– silenced / super silenced
Sound power level
– silenced / super silenced
Compressor
max. final compression temperature
Volume flow according to
ISO 1217 appendix C at:
– pmax =
[m3/min]
8 bar
– pmax = 10 bar
–
–
–
–
3
–
–
–
–
3
0.234
0.525
0.234
0.525
[m /min]
– pmax = 13 bar
[m /min]
Drive motor
Rated power
[kW]
3.0
5.5
3.0
5.5
Electrical power intake dryer
[kW]
–
–
0.21
0.28
Nominal speed
[min–1]
– 50 Hz
Protection type
Design
1500
3000
1500
3000
IP
55
55
55
55
IMB
35
35
35
35
F
F
F
F
400
400
400
400
ISO class
Electrical connection
Mains voltage compressor 1)
Mains voltage dryer
[V]
1)
Frequency 1)
Min. fuse protection
2) 3)
Recommended fuse protection
1)
2)
3)
2) 3)
[V]
–
–
230
230
[Hz]
50
50
50
50
[A]
16
20
16
20
[A]
20
25
20
25
Standard equipment. Mains voltages and frequencies are specified on a plate in the switch cabinet.
Only for 400 V / 50 Hz. The fuse values change in the case of other mains voltages and frequencies.
Use fuse gL – gG or circuit-breaker with C-characteristic only.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 13
Product description
2.2
Function description
Technical data for C 3 L...C 7 L Compressor assembly / Compressed air system, part 2
C 3 LDR...C 7 LDR Compressed air centre, part 2
C3L
C 3 LR
C 3 LDR
C4L
C 4 LR
C 4 LDR
C5L
C 5 LR
C 5 LDR
C7L
C 7 LR
C 7 LDR
[l]
4
4
4
4
[l]
1
1
1
1
Type
Oil filling quantity
Total oil filling quantity
Oil topping up quantity
between min. + max.
Intake air temperature
– min.
[°C]
5
5
5
5
– max.
[°C]
40
40
40
40
– free-standing installation
[m3/h]
800
1200
1600
2000
– with supply and exhaust
3
[m /h]
–
–
–
–
– free ventilator pressure
[Pa]
–
–
–
–
– free ventilator pressure
[mm WC]
–
–
–
–
8 bar: Switch-off press. pmax [bar]
–
–
–
–
Switch-on press. pmin [bar]
–
–
–
–
– pmax = 10 bar: Switch-off press. pmax [bar]
10
10
10
10
Switch-on press. pmin [bar]
9
9
9
9
– pmax = 13 bar: Switch-off press. pmax [bar]
–
13
–
13
Switch-on press. pmin [bar]
–
12
–
12
Cooling air requirement
Operating pressure values
(factory settings)
– pmax =
1)
Safety valve
Activation pressure at:
8 bar
[bar]
11
11
11
11
– pmax = 10 bar
[bar]
11
11
11
11
– pmax = 13 bar
[bar]
14
14
14
14
– pmax =
1)
Compressors for other operating pressures Pmin = Pmax –1 bar.
2.2 Function description
Function principle of the
air end
The air end operates according to the displacement principle. In the housing,
the main and secondary screws are driven by means of an electric motor.
Both screws have screw-shaped profiles, intermeshing without contact. Together with the housing wall, these screws form chambers which gradually reduce in size, seen in air flow direction.
Rotation of the rotors causes the air taken in to be compressed to the final
pressure in the chambers.
During compression oil is continuously injected into the air end. This having a
cooling, sealing and lubricating function.
Page 14
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Product description
2.2
Function description
Air circuit
Fig. 2.1: Components of the air circuit
1 Intake filter
The intake filter cleans the air suctioned by the air end.
2 Intake regulator
The intake regulator opens (load operation) or closes (idling operation or
standstill) the suction line depending on the operating condition of the
compressor.
3 Air end
The air end compresses the sucked in air.
4 Compressed air/oil receiver
The compressed air separates from the oil under the force of gravity in the
compressed air/oil receiver.
5 Oil separator
The oil separator separates the residual oil contained in the compressed
air.
6 Minimum pressure check valve
The minimum pressure check valve does not open until the system pressure has increased to 3.5 bar. This causes a rapid build-up of the system
pressure and ensures lubrication in the starting phase. Once the compressor has been switched off, the check valve prevents the compressed
air from flowing back out of the mains line.
7* Compressed air after-cooler (air cooled)
The compressed air is cooled in the compressed air after-cooler, causing
the water contained in the air to condensate.
8 Stop valve
The screw compressor may be isolated from the mains by means of the
stop valve.
* Optionally for receiver systems without refrigeration compressed air dryers
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 15
Product description
Oil circuit
2.2
Function description
The oil injected into the air end has the following functions:
–
It dissipates the compression heat (cooling)
–
It seals the gaps between the screws and between screws and housing
–
It lubricates the bearings
Fig. 2.2: Components of the oil circuit
1 Compressed air/oil receiver
The oil separated from the compressed air through the force of gravity collects in the compressed air/oil receiver.
The system pressure forces it out of the receiver into the air end.
2 Thermostatic oil control valve
Depending on the oil temperature, the thermostatic oil control valve either
allows the oil to pass through the oil cooler or through a bypass (e.g. in
the starting phase).´
Thus the oil constantly maintains its optimum operating temperature.
3 Oil cooler (air or water cooled)
The oil cooler cools down the hot oil to operating temperature.
4 Oil filter
The oil filter traps impurities in the oil.
5 Air end
The injected oil returns to the compressed air/oil receiver together with the
compressed air. There, it is separated through the force of gravity.
6 Drainage line
The air end suctions the residual oil which collects in the oil separator
back into the oil circuit via a drainage line.
Page 16
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Product description
2.3
Compressor control
2.3 Compressor control
Network pressure
For the compressor, the pressure downstream of the check valve is termed
network pressure. The control system switches the compressor on and off during operation depending on the network pressure.
Operating states
All screw compressor controls are based on three basic operating states:
1. Load operation
–
The compressor delivers its maximum amount of compressed air.
–
It consumes its maximum energy.
2. Idling operation
–
The compressor runs but does not deliver any compressed air.
–
It consumes approx. 75% less energy than in load operation.
–
When compressed air is required, it switches to load operation without
delay.
–
Idling operation reduces switching frequencies which can damage the
drive motor, and reduces wear of the system.
3. Standstill ready for operation
Operating modes
–
The compressor is standing still but ready for operation.
–
When compressed air is required, it switches automatically to load
–
operation.
The two most important operating modes are achieved by combining the three
operating states:
1. Intermittent operation
In intermittent operation the energy balance is perfect.
–
The compressor operates in load operation.
–
Upon reaching the switch-off pressure pmax the compressor switches
to standstill. It does not consume any energy.
–
Once the pressure has dropped to the switch-on pressure pmin the
compressor switches back to load operation.
2. Continuous operation
Continuous operation limits the drive motor switching cycles and reduces
wear to the system.
–
The compressor operates in load operation.
–
Upon reaching the switch-off pressure pmax the compressor switches
to idling operation.
–
Once the pressure has dropped to the switch-on pressure pmin the
compressor switches from idling operation back to load operation.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 17
Product description
2.4
Control devices
Short operating times
Attention!
During short operating times, the compressor does not reach its operating
temperature. It operates below the dew point. The generated condensate
mixes with the oil. The lubricating ability of the oil is reduced. This leads to
damage on the air end.
It is of utmost importance to consult BOGE, if you operate your system with
short operating times.
2.4 Control devices
Operating pressure
transmitter
The operating pressure transmitter enables an operation of the compressor
within the set switching limits.
Switch-on pressure pmin
If the supply pressure drops to the set switch-on pressure pmin, the compressor
switches on.
Switch-off pressure pmax
If the supply pressure increases to the switch-off pressure pmax, the compressor either switches off (intermittent operation) or switches to idling operation
(continuous operation).
2.5 Safety and monitoring devices
General
The safety devices guarantee a high degree of operational safety, in connection with the BOGE monitoring system.
When one of the safety devices responds, the control system reacts as follows:
–
The compressor is immediately switched off.
–
A flashing fault number in the left field of the display indicates the cause of
the fault.
Caution: Risk of injury!
Do not operate the compressor without built-in safety devices.
Do not dismantle the safety devices or put them out of operation.
The following monitoring devices are standard for BOGE control systems:
Page 18
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Product description
2.5
Safety and monitoring devices
Safety valve
The safety valve 1 on the
compressed air/oil receiver
prevents the maximum
admissible pressure being
exceeded.
Fig. 2.3: Safety valve
Caution: Risk of injury!
When the maximum pressure is exceeded (e.g. incorrect setting of the operating pressure value), the entire delivery volume of the compressor is ejected.
Safety temperature
limiting device
Monitoring the drive
motor
The safety temperature limiting device switches off the compressor once the
maximum admissible final compression temperature has been reached.
The compressor does not switch on when dropping below the minimum temperature.
–
Rectify the fault.
–
Acknowledge fault by pressing ENTER-key
–
Switch on the compressor (ON-button).
.
The drive motor is monitored by PTC resistors.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 19
Installation
3.1
Transport and storage
Part 3: Installation
3.1 Transport and storage
General
Please observe the generally accepted safety and accident prevention regulations when transporting the compressor. BOGE accepts no liability for damage caused by improper transport!
Attention!
The transport of the compressor may only be carried out by adequately instructed and authorized personnel!
The capacity of the lifting gear (lifting cart or forklift truck) must correspond at
least to that of the compressor (see Technical Data)!
Mind the position of the mass centre prior to lifting the compressor! The position of the mass centre is specified both in the attached dimensioned drawing
and on the packing of the compressor.
The compressor is delivered filled with oil. Do not tilt during transport!
Transport possibilities
Forklift truck or lifting cart transport
Ensure that the forks are underneath the
base frame of the compressor (see illustration).
See below if there is no base frame (crane
transport).
Fig. 3.1: Transport with forklift truck
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 21
Installation
3.1
Transport and storage
Crane transport
Attention!
Do not subject the safety cladding to force during transport. Protect the compressor using wooden spacers (see arrows in the following illustrations).
Remove the transport timbers.
Only use suitable transport slings having a
minimum length of approx. 8 metres.
Position the slings at the ends underneath
the base frame of the compressor.
Fig. 3.2: Crane transport
Intermediate storage
In case the compressor is not installed immediately after delivery, it has to be
stored at a sheltered location. It must be ensured that during the intermediate
storage neither dust nor humidity can penetrate.
Note!
In case of an intermediate storage please observe the specifications and
directions as to permissible environmental impacts (see chapter „3.2 Compressor room: Installation, maintenance conditions and application for compressed air receivers arranged below or separately“).
In case of a careless storage we assume no liability for consequent damages!
In the event of an extended intermediate storage you should consult BOGEService.
Please observe the directions for commissioning after an extended standstill
(see chapter „3.5 Commissioning“) if the intermediate storage takes longer
than two months.
Page 22
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Installation
3.2
Compressor room
3.2 Compressor room
Installation,
maintenance conditions
and application for
compressed air
receivers arranged
below or separately
Caution!
–
Protect compressed air receivers against damage through mechanical
effects (e.g. falling objects).
–
Operate the compressed air receiver and its equipment from a safe location.
–
Adhere to safety areas and safety clearances.
–
Ensure that the compressed air receiver stands securely. It must not shift
or tilt due to external forces. This also includes the additional weight during a pressure test!
–
The compressed air receiver must not be bolted to the base.
–
Ensure that the compressed air receiver is easily accessible from all
sides (for recurring tests). For the necessary operating and maintenance
areas have a look at the attached dimensioned drawings.
–
Ensure that the factory label is clearly visible.
–
Ensure that compressed air receivers are adequatly protected against
corrosion.
–
Only use the compressed air receiver for compressors operating with
cut-in and cut-out mode if the pressure fluctuation range amounts to
∆ p ≤ 20 % of the maximum operating pressure.
Installation surface
A level industrial floor without foundation is adequate for the installation of the
compressor. No special fastening elements are required.
Fire protection
The following applies to rooms in which compressors with oil injection cooling
are to be installed:
Caution!
–
For compressors with motor ratings exceeding 40 kW, ensure that the
compressor room is equipped with special fire protection.
–
Install compressors with motor ratings exceeding 100 kW in a separate
fire protected room.
Requirements of fire protected compressor rooms:
–
Walls, ceilings, floor and doors must be designed in fire protection class
F30 or higher.
–
Flammable liquids must never be stored in the compressor room.
–
The floor around the compressor must be made of non-flammable material.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 23
Installation
3.2
Compressor room
–
Leaking oil must not spread out over the floor.
–
No inflammable materials must be located within a radius of at least 3 metres around the compressor.
–
No inflammable machine parts, such as cable ducts, may run overhead of
the compressor.
Sound protection
Only install compressors in workrooms if the sound pressure level of
their measuring surfaces does not exceed 85 dB (A).
Admissible
environmental
influences
The compressor room must be clean, dry, cool and free of dust.
Admissible ambient temperatures
Maximum ambient temperature:
+ 40°C
Minimum ambient temperature:
+ 5°C
Attention!
Nonobservance of the admissible ambient temperature may lead to the
following problems:
–
The compressor will switch off when the admissible final compression
temperature is exceeded or gone below.
–
Pipe lines and valves will freeze up at low temperatures.
–
Damage due to reduced lubricating ability of the compressor oil.
Measures to be taken to ensure that admissible ambient temperatures
are observed:
Ventilation
–
Avoid any pipe lines or units radiating heat in the vicinity of the compressor, or insulate them well.
–
Never install the compressor in the cooling air flow of other machines.
–
Provide the supply air openings with adjustable louvres to ensure that the
minimum temperature is not gone below in winter.
–
Use of anti-freeze function (only in mode: Ready for operation).
If the following instructions are not observed, the admissible final compression temperature may be exceeded. In this case, the compressor
will switch off automatically.
Caution!
Arrange the compressor intake openings or ducts in such a way, that dangerous admixtures (e.g. explosive or chemically unstable materials) cannot
be drawn in.
Ventilation openings (free-standing installation)
Page 24
–
Arrange supply air openings close to the floor.
–
Arrange exhaust air openings in the ceiling or at the top of the wall.
–
The required cross sections for the supply openings (as well as for the
flaps and weather protection grids) are indicated in the table.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Installation
3.2
Compressor room
Ventilators
Ensure that the heated exhaust air is not taken in again.
If necessary, the heated air must be extracted by ventilators.
To ensure perfect cooling even at higher temperatures in the summer, the ventilators must be designed as follows:
Cooling air requirement
–
The ventilator capacity must be rated approx. 10 – 15% higher than the
sum of the cooling air quantity required for all machines operated in the
room (VDMA Code of Practice sheet 4363 "Ventilation of compressor
rooms").
–
For a free-standing installation, the cooling air requirement specified in the
table corresponds to the required ventilator capacity.
Please refer to the following table for the cooling air requirement and size of
the supply air openings for your compressor. Ensure that flaps and weather
protection grids have the necessary free cross section. We generally recommend contacting a specialist company for performing the duct construction
work and planning.
Type
C 3 L / C 3 LR / C 3 LDR
C 4 L / C 4 LR / C 4 LDR
C 5 L / C 5 LR / C 5 LDR
C 7 L / C 7 LR / C 7 LDR
*
Drive rating
* Cooling air
requirement
for free
standing unit
Necessary inlet
opening
for free
standing unit
[kW]
[m3/h]
[m2]
2.2
3.0
4.0
5.5
800
1200
1600
2000
0.10
0.20
0.20
0.25
For the cooling air requirements the basis is a 4°C temperature difference between room and outside temperature
Tab. 3.1: Cooling air requirement, necessary aperture dimensions
Condensate disposal
The air taken in contains water in form of vapour, which turns into condensation during compression.
Attention!
The condensate contains oil. Never lead it into the public sewage system
without prior treatment.
Strictly observe the effluent disposal laws of your local authorities.
Oil-water separator
The BOGE-oil-water-separator separates the oil from the condensate.
The cleaned water may be fed directly into the public sewage system.
The oil is collected in a separate container. Dispose of the oil according to
environmental regulations.
If, due to special operating conditions, the oil should emulsify, use an emulsion cracking plant.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 25
Installation
3.3
Installation
3.3 Installation
General
BOGE compressor units are supplied ready for connection. Only the work described in the following paragraphs needs to be carried out during the installation.
Caution!
Only have the installation work carried out by appropriately trained persons
or specialists.
Lay out all energy supply lines in a trip-proof and barrier-free manner so that
potential accidents can be avoided!
Prior to delivery, each compressor is subjected to a trail run at the factory. It
is carefully tested and set. However, possible transport damage cannot be
excluded.
Checking the delivery
scope
–
Please inspect the compressor immediately after delivery and direct damage claims to the last haulier – even when the packing is not damaged! To
safeguard claims against the haulier we recommend leaving the machine,
devices and packing material in the same condition as they were in when
the damage was detected.
–
Prior to commissioning, check the compressor for external damage.
–
Observe the compressor very closely during commissioning and the following trial run.
–
If malfunctions occur, switch off the compressor immediately and inform
the BOGE-Service.
The delivery scope depends on your order.
Prior to commissioning, please check whether all required parts have been
provided. Please check the order confirmation for any possible accessory
equipment.
–
Installing the
compressor
Page 26
The delivery scope includes the following component parts:
–
Operating instructions
–
Electric circuit diagram (in the compartment of the switch cabinet)
–
List of electrical equipment (in the compartment of the switch cabinet)
–
Oil drainage hose
–
Head nut (in the compartment of the switch cabinet)
–
Spare parts list
–
Remove the packing material on and in the compressor.
–
Install compressor and align horizontally.
The compressor must stand firmly on the ground on all feet.
–
For compressor assemblies of the series C 3 L to C 7 L the operating
height of he control has to be 400 mm according to EN 60204 400.
–
For this reason the compressor assembly has to be installed on a console
or pedestal (on site).
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Installation
Connecting the
compressor to the
compressed air network
3.4
Electrical connection
–
The compressors have to be installed in such a manner that an ergonomically convenient operation from the operator's stand is guaranteed.
–
The local specifications of the EN 60204 regulations always have to be
complied with.
–
Connect the compressor to the compressed air network or a compressed
air receiver.
–
For this, use a BOGE high pressure hose.
For pneumatic connection see dimensioned drawing.
Note!
Do not install a check valve in the pressure line.
The compressor is already equipped with a check valve.
Checking the oil level
BOGE compressors are supplied with a complete oil filling.
Prior to commissioning/start up, check the oil level as described in chapter
"Maintenance".
3.4 Electrical connection
Warning: Voltage!
Ensure that work on the electrical equipment of the compressor is only carried out by authorized electricians.
When connecting to the power supply, observe the valid VDE, DIN and EVU
regulations or the local safety regulations.
Also observe the regulations of your local power supply company regarding
the load rating of your power supply.
Mains disconnecting device
According to accident prevention regulation VBG 5, § 12, the customer is responsible to provide the following safety measures:
Each compressor plant has to be equipped with a power disconnecting device
according to DIN EN 60204-1:2007.
Please refer to the "Technical data" for the design and fuse rating.
Rated voltage
The data of your mains (operating voltage, control voltage, type of current, frequency, ...) must coincide with the data on the type plate on the switch cabinet.
In the event of deviations, please contact the BOGE service or your supplier.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 27
Installation
3.5
Commissioning
Connecting the leads
–
Check to ensure that all terminals in the switch cabinet are firmly tightened. If necessary, retighten the screw connections.
–
Guide the lead cable through the PG screw connection.
–
Connect the leads L1, L2, L3, N, Pe (PEN) firmly to the power supply terminal.
A clockwise rotational field must be created.
–
Retighten the electrical connections after the first 50 operating hours.
Caution: Risk of injury!
Prior to any work on the compressor:
–
Press Emergency Stop button, open mains disconnection device and
secure against unintentional switch on by means of a padlock.
–
Check to ensure that all conducting machine parts are voltage free.
–
Depressurize all areas under pressure.
Never omit a single safety step! Otherwise, you will risk injuries due to restarting, electric shock or self-releasing parts.
Caution!
With an activated automatic restart (Auto-Restart) the compressor may restart automatically after a voltage failure.
Prerequisite: The network pressure is lower than the set cut-in pressure of
the operating switch and it was already switched on before the mains failure
– green indicator lamp = ON.
3.5 Commissioning
Note!
We recommend the drawing up of a commissioning certificate in which the
test results during the commissioning process can be listed up.
Caution: Risk of injury!
The commissioning may only be carried out by experienced and authorized
qualified personnel!
Always wear protective gloves when working on the compressor to avoid
bruising of fingers or hands while opening or closing components!
Page 28
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Installation
3.5
Commissioning
Check installation
requirements
Attention!
Make sure that the compressor is installed according to the installation requirements!
List up the test results in the commissioning certificate.
Checking the rotational
direction
Attention!
Always check the rotational direction of the drive motor prior to commissioning/initial start up.
Even brief operation in the wrong direction of rotation (more than approx.
5 seconds) may cause total destruction of the air end!
List up the test results in the commissioning certificate.
Caution!
Ensure that the rotational direction coincides with the rotational direction arrow on the air end.
–
Close mains disconnecting device.
–
Switch the compressor on and immediately off again to check the rotational direction.
Changing the rotational direction
Caution: Risk of injury!
Press Emergency Stop button, open mains disconnection device and secure
against unintentional switch on by means of a padlock.
–
Interchange two phases (L1, L2 or L3) in the power cable.
Check compressed air
outlet for tightness
Caution: Risk of injury!
Work on the compressed air system may only be carried out by experienced
and authorized qualified personnel!
Always wear protective clothing and goggles!
Immediately after having switched on the machine the connection of the
compressed air outlet must be checked for tightness!
Make sure to observe an appropriate safety distance during the inspection!
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 29
Installation
3.5
Commissioning
–
Close mains disconnecting device.
–
To conduct the inspection switch on the compressor and check the compressed air outlet for tightness.
–
Switch off compressor.
Caution: Risk of injury!
Press Emergency Stop button, open mains disconnection device and secure
against unintentional switch on by means of a padlock.
Opening the stop valves
–
If necessary, have leakages repaired by skilled qualified pesonnel.
–
List up the test results in the commissioning certificate.
Open ball valve on the compressor delivery.
Checking for leaks
Caution: Risk of injury!
In case of leakages in the oil circuit there is a certain danger to slip and fall
because of oil spills!
Have all connections of the oil circuit checked for leakages by authorized
qualified personnel!
During the inspection slip-resistant safety shoes and protective clothing are
obligatory!
Undertake the following to prevent leaks:
Conduct trial run
–
Check screw connection of the lines and retighten, if necessary.
–
Close mains disconnecting device.
–
Switch on the compressor using the ON key. The compressor starts.
–
When the factory-set switch-off pressure is reached, the compressor cuts
off automatically.
–
Check network pressure on control display. If necessary, reset operating
pressure (pressure target value).
–
The compressor is ready for operation.
Switch off the compressor after a trial run of several hours under maximum
load.
List up the test results in the commissioning certificate.
Page 30
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Installation
Commissioning
following extended
stoppages
3.5
Commissioning
If an extended stoppage is scheduled, you should contact BOGE-Service beforehand.
Following an extended stoppage of more than 2 months, fill a small amount of
oil in the suction controller prior to starting the compressor.
Attention!
Only fill the suction controller with the grade of oil used to operate the compressor.
Never mix different oil grades and brands.
Caution: Risk of injury!
Press Emergency Stop button, open mains disconnection device and secure
against unintentional switch on by means of a padlock.
–
Unscrew the plug on the
suction controller 1.
–
Fill approx. 1/4 l compressor oil into the suction
controller.
–
Reclose the controller
using the plug.
–
Turn compressor stage
at the shaft by hand 5- to
10 times to spread the oil
evenly.
Fig. 3.3: Suction controller
Refrigeration
compressed air dryer
Before commissioning the refrigeration compressed air dryer read attached
operating instructions.
Caution: Risk of injury!
Observe all safety notes specified in the attached operating instructions
when working with coolants!
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 31
Installation
3.6
Dismantling
3.6 Dismantling
Note!
To avoid dangers when dismantling the compressor please consult your
BOGE Service:
Telephone: +49 5206 601-140
Caution!
Dismantling of the compressor may only be carried out by experienced and
authorized qualified personnel!
Make also sure to observe all information in the attached operation instructions as to a safe dismantling of the refrigeration compressed air dryer and a
secure disposal of the coolant!
Warning: Voltage!
All work on the electrical installation may only be carried out by authorized
and skilled electricians!
Prior to starting the work the power cable to the switch cabinet must be disconnected from the mains and secured against unintentional switching on!
Page 32
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Faults
Part 4: Faults
4.1
General
4.1 General
The tables on the following pages give information on the possible causes
of operating faults and measures for their rectification (please also refer to
operating instructions of the compressor control).
Caution!
Ensure that any work required to rectify faults is only carried out by qualified
personnel or specialists.
Ensure that components which have a safety function are only set, repaired
or exchanged by BOGE Service!
Please contact BOGE-Service at the following telephone number, if you have
any questions.
Telephone: +49 5206 601-140
4.2 General faults
Fault
Possible cause
Rectification
No quantity delivered,
no pressure build-up,
max. pressure 0.5 bar
System components in the
compressor are leaking
Check oil and compressed air lines inside the compressor; tighten
and/or reseal screw connections, if necessary
Minimum pressure valve is
defective
Close ball valve and check whether pressure builds up; if so, open
ball valve again immediately; replace minimum pressure valve
Electromagnetic venting valve
does not close
Check solenoid valve and replace, if necessary
Suction controller does
not open
Suction controller or solenoid valve is defective; check and replace,
if necessary
No electric power to compressor
Check electrical connection
Fuses are defective
Check the mains and control fuses, replace if necessary
Machine has not vented
perfectly
Check venting valve and replace, if necessary
Voltage fluctuations in the electrical mains power
Ensure constant voltage in accordance with IEC 38
Compressor oil is very viscous
due to low ambient temperature
Heat up the compressor system (additional heater available as an
option)
Compressor system does
not start up
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 33
Faults
4.2
General faults
Fault
Possible cause
Rectification
Oil in suction filter
Minimum pressure non-return
valve is leaking
Check the minimum pressure check valve and replace, if necessary
Suction controller is leaking
Check the suction controller and replace, if necessary
Cut-out performed by
emergency-off switch
Cut-out normally via O-key
Drain line is blocked
Dismantle and clean drain line
Defective oil separator element
Check oil separator and replace, if necessary
Excessive oil filling
Drain off oil
Operating pressure target value
maladjusted
Set operating pressure to maximum permissible pressure of the
screw compressor
Defective safety valve
Replace safety valve
Venting valve does not open
Check venting valve and replace, if necessary
Check valve is leaking
Check the valve and replace, if necessary
Excessive oil
consumption
Safety valve blows
System pressure does
not decrease when
switching off
Page 34
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Maintenance
Part 5: Maintenance
5.1
Safety instructions
5.1 Safety instructions
Caution!
Ensure that maintenance work is ony carried out by specialists or appropriately trained persons.
–
Prior to starting any maintenance work, always stop the compressor as
described in these operating instructions before removing any safety
cladding or safety devices. Refit the safety cladding or safety devices
immediately upon completion of the maintenance work.
–
Heavy components may only be lifted up by various persons in due consideration of the local industrial safety regulations.
–
Only use original spare parts, compressor oils and operating materials
released by BOGE for the maintenance work.
–
With an activated automatic restart (Auto-Restart) the compressor may
restart automatically after a voltage failure.
Prerequisite: The net pressure is lower than the set switch-on pressure.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 35
Maintenance
5.1
Safety instructions
Caution: Risk of injury!
Always adhere to the prescribed operating method described below for all
maintenance work. Never omit a single safety step!
Otherwise you will risk injury from restarting, electric shock or parts which
may fly off.
Prior to all maintenance work:
1. Switch off the compressor using the OFF button.
2. Press Emergency Stop button.
3. Press Emergency Stop button, open mains disconnection device and
secure against unintentional switch on by means of a padlock.
4. Fix a warning label to the control and fill in the name of the person responsible who is authorized to switch on the maschine again.
5. Check to ensure that all machine elements are definitely currentless.
6. Prior to starting work let cool down all hot components of the compressor
to 50°C.
7. Separate the compressor from the compressed air network by closing
the ball valve at the compressed air outlet.
8. Vent the compressor.
To do so,open the safety valve on the combined compressed air-oil receiver as follows:
– Turn the knurled nut anticlockwise until you can feel a resilient resistance.
–
Tun the knurled nut a little further.
Any possibly existing air will escape.
The system pressure gauge will indicate a pressure of 0 bar.
–
Once the residual air has completely escaped from the system, firmly
retighten the knurled nut.
9. Remove all safety cladding necessary to perform the maintenance work.
Once the maintenance work has been concluded:
10. Reattach all removed safety cladding.
11. Open the ball valve at the compressed air outlet.
12. Prior to switching on again, check whether anyone else is working on the
compressor!
13. Remove warning sign not until then and release mains disconnecting
device.
14. Unlock Emergency Stop button.
Page 36
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Maintenance
5.2
General
5.2 General
Maintenance through
BOGE customer service
Have BOGE service check your compressor every 3.000 operating hours or
annually.
Note!
Maintenance agreement!
Enter into a maintenance agreement with BOGE.
BOGE service will carry out the proper maintenance on your compressor at
regular intervals. This guarantees maximum safety and realiability of your
compressed air supply.
Review of regular
maintenance work
Fig. 5.1: Review of regular maintenance work
1 Check / adjust pressure
2 Clean oil cooler
3 Top up oil in the suction controller after an extended down time
4 Check suction filter
– Clean / Change filter cartridge
5 Change oil filter
6 Change oil separator
7 – Check oil level
– Top up oil
8 Change oil
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 37
Maintenance
Maintenance intervals
5.2
General
The maintenance intervals specified in the table are based on average operating and ambient conditions.
Extreme conditions may require shorter maintenance intervals.
Note!
Note down any maintenance work in the table on the last page. This will facilitate trouble shooting for Boge service.
Attention!
Check monthly if all screw connections on the compressor are fully tightened.
Oil change:
Please change oil and replace oil filter and nozzle with dirt catch after the first
500 operating hours!
Page 38
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Maintenance
5.2
General
Maintenance intervals in operating hours 1)
Maintenance work
weekly,
monthly
1.000
annually
1.500
annually
3.000
annually
Page
9.000
every
2 years
General maintenance work
Check final compression temperature
(set point value: 70...100°C)
w
Control
Check compressor for leaks
X
–
Check system relief on system pressure gauge (22)
(set point value: 0 – 1.5 bar)
w
Control
Check function of EMERGENCY STOP button
m
–
Clean oil cooler
X
51
Draining off condensate from compr. air receiver
w
–
Check automatic condensate drainage
w
–
Check if electrical connections are tightened
X
–
Air circuit
Check and if necessary clean suction filter
m
43
Change suction filter cartridge
X
44
Check safety valve
X
52
Replace minimum pressure valve
(wearing parts set)
X
–
Replace suction controller
X
–
Oil circuit
X
Check oil level and top up as required 2)
45
Change oil separator 2)
X
47
Change oil filter 2)
X
46
X
Change oil 2)
48
Replace oil regulator (wearing parts set)
X
–
Replace nozzle with dirt catch
X
–
Drive
1)
2)
Lubricate drive motor bearings
Drive motors with permanent lubrication
Replace motor bearing
Depending on mains frequency: 50 Hz 10.000 operating hours
60 Hz 8.000 operating hours
44
If the compressor is not often used, undertake the maintenance according to the specified intervals (weekly/monthly/annually) depending on the number of operating
hours.
The specified intervals only apply when BOGE compressor oil Syprem 8000 S is used! The service life may differ depending on the ambient temperature. In this case
have the oil analyzed by your BOGE service!
Tab. 5.1: Maintenance intervals
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 39
Maintenance
5.2
General
General information
concerning the
lubricants used
Caution: Risk of injury!
Oil presents a potential danger to health and environment due to their
additives.
–
Avoid contact with skin and eyes.
Wear protective gloves made of resistant synthetic material.
Wash yourself thoroughly after contact with oils.
–
Do not inhale the fumes or mist.
–
Protect your environment.
Ensure that no oil is spilt.
–
Fire, naked flames and smoking is strictly prohibited when handling oil.
We recommend using only oil according to the following specification:
Page 40
–
Viscosity range of 55 mm2/s at 40°C.
–
Minimum viscosity at 100°C of 8 mm2/s.
–
Maximum viscosity at 0°C of 1.000 mm2/s.
–
Failure load stage 10, FZG-Test, DIN 51 354-02/ ISO DIS 14 635-1.
–
Test Method A/8,3/90 10.
–
Excellent oxidation stability: Meets requirements of Pneurop oxidation
test.
–
Antifoam – additives.
–
Additives to prevent residue formation.
–
Compatibility with all materials which are resistant to mineral hydrocarbons, e.g. Neoprene, NBR, FPM, PTFE, acrylic and epoxy resin pains,
nylon (polyamide) and PVC.
–
Flash point (DIN ISO 2592) > 230°C.
–
Excellent demulsifying properties.
–
Additives for corrosion protection of metallic surfaces.
–
Excellent oxidation stability: Rotating bomb oxidation Test (ASTM D 2272)
higher than 2,400 minutes.
–
Meets VDL requirements DIN 51 506 (including Pneurop test).
–
Or you use BOGE compressor oil Syprem 8000 S.
The stated maintenance intervals refer to the use of Syprem 8000 S only.
–
Syprem 8000 S can be purchased from BOGE retailers.
–
Never mix different oil types and brands. The additives may be incompatible. It may lead to foam formation, premature aging or loss of lubricating
ability.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Maintenance
5.2
General
Disposal of used
operating material
Attention!
The handling and disposal of mineral oils is subject to legal regulations.
It is an offense not to ensure correct and safe disposal of old oil!
Please instruct one of the known service companies to dispose of used
operating materials or deliver them to an authorized disposal point.
Observe the following points when disposing of old oil:
–
Never mix the oil with other material or liquids.
–
Used oil filters and oil separator cartridges require special waste treatment and must be kept separate from normal waste!
Pressure hoses
Caution!
Risk of injury and damage to compressor due to obsolete pressure hoses!
Never use pressure hoses beyond the prescribed service life!
Check hoses and connections regularly for leakages! Check the service life
of the hoses and replace them in due time!
As replacement only use original spare parts released by BOGE!
Used pressure hoses are not permitted as a replacement!
Spare and wearing parts
Caution!
Only use original spare parts, compressor oils and operating materials
released by BOGE for repair and maintenance work.
BOGE is not liable for any damage resulting from the use of other spare parts
or operating materials.
Attention!
If the nozzle with dirt catch is soiled the oil consumption may increase significantly!
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 41
Maintenance
5.3
Regular maintenance work
5.3 Regular maintenance work
Draining off the
condensate from the
compressed air receiver
Draining:
If no automatic condensate darining is fitted, then drain off the condensate at
least once a week.
Attention!
The compressor is lubricated with oil. The condensate contains oil and may
not be drained off into the public sewage system!
Pay attention to the pertaining rules and regulations of your local authorities!
–
Switch off the compressor using the OFF button.
Caution: Risk of injury!
Press Emergency Stop button, open mains disconnection device and secure
against unintentional switch on by means of a padlock.
–
Depressurize receiver.
–
Place a suitable basin underneath the condensate drain of the receiver.
–
Open the ball valve and drain off the condensate.
–
Close the ball valve again.
–
Dispose the condensate properly.
Fig. 5.2: Draining off the condensate manually
Page 42
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Maintenance
Draining off the
condensate from the
compressed air receiver
with automatic
condensate separator
5.3
Regular maintenance work
The fully automatic, electronically controlled condensate separator is equipped
with a wear free sensor which monitors the condensate level in the integrated
collecting basin. As soon as the collecting basin is full, a solenoid valve opens
and the condensate is drained off.
Note!
Unlike the Konsatronik the fully automatic condensate separator operates
without causing any pressure losses. In the event of a malfunction a red LED
lights up and a potential-free contact is switched. Regularly check the function using the additional test switch on the device.
Fig. 5.3: Fully automatic, electronically controlled condensate separator
1 Condensate shut-off valve on receiver
2 Condensate outlet (to oil-water separator)
3 Electr. power supply
Clean or change suction
filter
Cleaning:
–
1x monthly, however, at least every 500 operating hours.
–
Correspondingly earlier if the air taken in is heavily soiled.
Change:
–
In the event of damage.
–
After the second cleaning.
–
Switch off the compressor with the OFF button.
Caution: Risk of injury!
Press Emergency Stop button, open mains disconnection device and secure
against unintentional switch on by means of a padlock.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 43
Maintenance
5.3
Regular maintenance work
Removing the filter cartridge
Remove lid (1) of the filter
housing.
Remove filter cartridge (2).
Fig. 5.4: Changing the suction filter
Cleaning the filter
cartridge
Attention!
Do not clean filter cartridges in liquids.
Do not use any hard objects when cleaning to avoid damaging the filter
paper.
Refit a new filter cartridge in the event of damage or when it has been
cleaned twice.
–
Hit on the filter cartridge using the palm of your hand to knock out coarse
dust.
–
Blow out fine dust from the inside to the outside using dry compressed
air (maximum pressure 5 bar).
–
Clean the sealing surface of the filter cartridge.
Fitting a filter cartridge
Drive motors with
permanent lubrication
–
Insert filter cartridge into the filter housing.
–
Attach lid of the filter housing.
As a rule, the bearings of the drive motors are provided with a maintenance
free permanent lubrication.
Under normal operating conditions (coolant temperature max. 40°C, continous
operation) the bearings are maintenance free for the service life.
For motor maintenance see operating instructions of the compressor comtrol.
Page 44
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Maintenance
5.3
Regular maintenance work
The service life decreases or increases as thermal stress increases or
decreases (due to increased or reduced coolant temperature).
Attention!
Have BOGE service dismantle the bearings and install new bearings once
the specified service life has expired!
Checking the oil level,
topping up oil
Check:
–
Prior to commissioning/start-up of the compressor.
–
Then every 1.000 operating hours, however at least once a year.
Topping up:
–
When the oil level has dropped below the "min." mark (see sketch).
Attention!
Always use the same oil type when topping up. Never mix different oil types
and brands.
–
Switch off the compressor using the OFF button.
Caution: Risk of injury!
Press Emergency Stop button, open mains disconnection device and secure
against unintentional switch on by means of a padlock.
–
Close ball valve at the compressed air outlet.
–
Vent the compressor (as described in the beginning of the chapter).
–
Wait approx. 3 minutes to permit the oil to settle.
Caution: Risk of injury!
Danger of burning due to hot oil!
Always wear safety gloves!
–
Remove plug (1) of oil filling socket (2) (see figure below).
–
Check oil level.
The oil level must not drop below the "min." mark (see sketch).
–
If necessary, top up with oil to the lower edge of the thread ("max." mark)
on the oil filling socket.
–
Screw plug ‚ back in.
–
Open ball valve at the compressed air outlet.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 45
Maintenance
5.3
Regular maintenance work
Fig. 5.5: Checking the oil level, topping up with oil
Changing the oil filter
Change:
–
After the first 500 operating hours.
–
After 3.000 operating hours, however, no later than after one year.
–
With each oil change!
–
Switch off the compressor using the OFF button.
Caution: Risk of injury!
Press Emergency Stop button, open mains disconnection device and secure
against unintentional switch on by means of a padlock.
–
Close ball valve at the compressed air outlet.
–
Vent the compressor (procedure as described above).
–
Wait approx. 3 minutes to permit the oil to settle.
Caution: Risk of injury!
Do not touch hot surfaces!
Page 46
–
Slacken screws on service cover (3) and remove cover.
–
Take out oil filter cartridge (4) and remove from support body (5).
–
Slide support body into the new oil filter cartridge.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Maintenance
5.3
Regular maintenance work
Attention!
Over-current / Non-return valve(6) must be fitted facing up.
–
Fit oil filter cartridge (4) with support body (5).
–
Check o-rings on service cover for damage and replace if necessary.
–
Fit service cover (3) and tighten screws.
–
Open ball valve at the compressed air outlet.
–
Switch on compressor and run till it reaches operating temperature.
–
Check tightness of service cover and re-tighten screws.
Fig. 5.6: Changing the oil filter / Changing the oil separators
Changing the oil
separator
Change:
–
When warning message "8" appears on the control system display (RATIO
only).
–
After 3.000 operating hours, however, no later than after one year.
Caution: Risk of injury!
If the prescribed maintenance intervals are not observed, the oil separators
might become blocked. In this case, the differential pressure will increase
until the safety valve blows.
–
Switch off the compressor using the OFF button.
Caution: Risk of injury!
Press Emergency Stop button, open mains disconnection device and secure
against unintentional switch on by means of a padlock.
–
Do not touch hot surfaces!
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 47
Maintenance
Oil change
5.3
Regular maintenance work
–
Slacken screws on service cover (3) and remove cover.
–
Pull oil disperser cartridg (1) up out of the o-ring seal.
–
Check seat of o-ring.
–
Lightly oil bottom of new cartridge in and press into o-ring seal.
–
Check o-rings on service cover for damage and replace if necessary.
–
Fit service cover (3) and tighten screws.
–
Open ball tap at compressed air exit.
–
Switch on compressor and run till it reaches operating temperature.
–
Check tightness of service cover and re-tighten screws.
Change:
–
After 9.000 operating hours, however, at the latest after two years.
–
For other types of oil the appropriate oil change intervals must be complied
with.
Note!
The service life of the oil, the oil filter and oil separators is reduced under the
following conditions:
–
When the compressor is operated at extreme ambient temperatures.
–
When the intake air is extremely soiled.
Building up a pressure cushion
The combined compressed air / oil receiver is located at the lowest point of the
system. Therefore, a light pressure cushion (approx. 1.5 bar system pressure)
must be applied to drain the oil. This pressure cushion forces the oil through
the drain hose into a suitable collecting basin.
–
Switch off the compressor using the OFF button.
Caution: Risk of injury!
Press Emergency Stop button, open mains disconnection device and secure
against unintentional switch on by means of a padlock.
Draining old oil
–
Switch off compressor.
–
Open ball valve at the compressed air outlet.
–
Switch off compressor. After approx 2 sec screw cap nut (5) on the bleed
aperture of the magnetic valve (the nut is located in the storage compartment of the switch cabinet).
Caution: Risk of injury!
Danger of burning due to hot oil!
Always wear safety gloves!
Page 48
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Maintenance
5.3
Regular maintenance work
–
Remove blind plu (1) at oil drain (3) with the tap closed.
–
Fit oil drainage hose (2) (the hose is located on the machine).
–
Place the oil drain hose into a suitable container.
–
Slowly open the stop valve. The pressure cushion forces the oil into the
container.
–
Once the compressed air/oil receiver has been completely drained, close
the stop valve.
–
Remove oil drainage hose and replace blind plug with new copper seal.
–
Remove the cap nut from the solenoid valve.
–
Change oil filter (procedure as described above).
–
Change oil separators (procedure as described above).
Filling with new oil:
–
Fill up to the edge of the thread of the filling socket (max.) (procedure as
described above).
Attention!
After each oil change you have to fill a small quantity of oil into the suction
controller before starting the compressor.
For oil quantity and procedure see chapter "Installation", chapter "Commissioning following extended stoppages".
Attention!
Always fill with the same oil type as previously used. Never mix different oil
types and brands.
The oil circuit must be flushed prior to changing the oil type.
–
Conduct trial run.
Caution: Risk of injury!
Press Emergency Stop button, open mains disconnection device and secure
against unintentional switch on by means of a padlock.
–
Check the oil filters and oil separators for leaks and tighten by hand, if
necessary (procedure as described above).
–
Check oil level (procedure as described above).
Top up oil losses, if any.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 49
Maintenance
5.3
Regular maintenance work
Fig. 5.7: Solenoid valve on the suction controller with the cap nut screwed on
Fig. 5.8: Oil drain from oil compressed air receiver
Fig. 5.9: Oil drain with fitted oil drainage hose
Flushing the oil circuit
Flushing the oil circuit with clean oil becomes necessary:
–
When the oil is excessively soiled.
–
Prior to changing the oil type.
Attention!
Detailed information as to the flushing with BOGE oils you can obtain from
the following service number:
Telephone: +49 5206 601-140
Page 50
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Maintenance
Cleaning the
compressed air/oil
cooling unit
5.3
Regular maintenance work
Cleaning:
–
After 1.500 operating hours, however, at the latest after one year.
Note!
The service life of the compressed air/oil cooling unit depends on the degree
of soiling (dust, oil vapour) of the suctioned cooling air. Extreme external soiling of the cooling unit leads to an increased temperature in the oil circuit.
–
Switch off the compressor using the OFF button.
Caution: Risk of injury!
Press Emergency Stop button, open mains disconnection device and secure
against unintentional switch on by means of a padlock.
Attention!
Do not use any sharp objects for cleaning!
These could damage the cooling unit!
–
Blow down the dirt with compressed air in the opposite direction to the
normal cooling air flow. Vacuum out the dirt using an industrial vacuum
cleaner.
If the cooling unit is excessively soiled (cleaning is no longer possible with
compressed air), have it disassembled and cleaned by BOGE service.
Compressed air/oil cooling unit
Fig. 5.10: Cleaning the compressed air/oil cooling unit
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 51
Maintenance
Checking the safety
valve
5.3
Regular maintenance work
Check:
–
After approx. 3.000 operating hours, however, at least once a year.
Check safety valve by opening the screw plug (1).
Caution: Risk of injury!
Danger of burning due to hot oil!
Take extreme care when checking the safety valve with the compressor
running taking all safety measures into consideration.
Always wear safety gloves!
A hot air-oil mixture escapes when opening!
–
Open the threaded plug (1) anticlockwise. The compressed air escapes.
–
Tighten the threaded plug by turning clockwise.
Fig. 5.11: Check safety valve
Page 52
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Maintenance
5.4
Spare parts and optional equipment
5.4 Spare parts and optional equipment
List of spare and
wearing parts
(for maintenance)
Designation
Compressor oil Syprem 8000 S
Maintenance kit consisting of:
oil filter, oil separator, suction filter cartridge, gaskets, nozzle with dirt catch
Wearing part kits for:
oil regulator, minimum pressure valve, solenoid valve
Intake regulator incl. solenoid valve
List of available optional
equipment
Designation
Optional equipment for compressed air treatment
Oil/water separator
Automatic condensate draining unit Bekomat
Attention!
When ordering, please specify the data on the type plate:
–
Type
–
Year of manufacture
–
Machine number
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 53
Appendix
Part 6: Appendix
6.1
Flow chart
6.1 Flow chart
On the following pages you will find the individual flow charts for the different
machine types and components.
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 55
Appendix
6.1
Flow chart
Air cooled version,
standard
Page 56
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Appendix
6.1
Flow chart
101 Intake air INLET
102 Compressed air OUTLET
1 Suction filter
4 Suction controller
5 Ventilation and regulation control valve
7 Drive motor
8 Compressor air end
9 Final compression temperature display and switch
10 Combined compressed air/oil receiver
11 Oil separator
12 Safety valve
15 Compressed air after-cooler
Optionally for receiver systems without refrigeration compressed airdryer
16 Thermostatic oil control valve
17 Oil cooler
18 Oil filter
21 Minimum pressure check valve
23 Network pressure transmitter
24 Pressure gauge reading in display
25 Stop valve, compressed air outlet
27 Stop valve, oil drainage
28 Throttle with filter
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Page 57
Page 58
Operating
hours
System
pressure
** Co = Control
** Ch = Change
Network
pressure
Temperature
Intake
filter
*
Oilfilter
Öllevel
**
Oilseparator
Cooling
unit
cleaning
Motor
maintenance
Compressed
air dryer
Remarks
6.2
* Cl = Cleaning
* Ch = Change
Date
Please note the completed maintenance work in the respective columns
Appendix
List of maintenance and service work
6.2 List of maintenance and service work
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Operating
hours
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
System
pressure
** Co = Control
** Ch = Change
Network
pressure
Temperature
Intake
filter
*
Oilfilter
Öllevel
**
Oilseparator
Cooling
unit
cleaning
Motor
maintenance
Compressed
air dryer
Remarks
6.2
* Cl = Cleaning
* Ch = Change
Date
Please note the completed maintenance work in the respective columns
Appendix
List of maintenance and service work
Page 59
Page 60
Operating
hours
System
pressure
** Co = Control
** Ch = Change
Network
pressure
Temperature
Intake
filter
*
Oilfilter
Öllevel
**
Oilseparator
Cooling
unit
cleaning
Motor
maintenance
Compressed
air dryer
Remarks
6.2
* Cl = Cleaning
* Ch = Change
Date
Please note the completed maintenance work in the respective columns
Appendix
List of maintenance and service work
BOGE Operating instructions for C 3 L...C 7 L series screw compressors
Download PDF

advertising