JU-1000 English Operation Manual - AV-iQ

IP CONTROL SYSTEM JUNCTION UNIT
JU-1000
OPERATING INSTRUCTIONS
Safety Instructions
Carefully read all safety messages in this manual and safety Instructions on your equipment.
Follow recommended precautions and safe operating practices.
SAFETY ALERT SYMBOL
!
This is the “Safety Alert Symbol.” This symbol is used to call your attention to items or operations
that could be dangerous to you or other persons using this equipment. Read these messages and
follow these instructions carefully.
It is essential that you read the instructions and safety regulations before you attempt to assemble or use this
equipment.
The definitions of signal words are as follows:
! WARNING
WARNING: Personal danger
Warning notes indicate any condition or practice, which if not strictly observed, could result
in personal injury or possible death.
! CAUTION
CAUTION: Possible damage to equipment
Caution notes indicate any condition or practice, which if not strictly observed or remedied,
could result in damage or destruction of the equipment.
NOTE
NOTE: Notes indicate an area or subject of special merit, emphasizing either the
products capabilities or common errors in operation or maintenance.
! WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
COLOR CAMERA TO RAIN OR MOISTURE.
AVERTISSEMENT
Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas exposer l’appareil á la pluie ou á l’humidité.
Afin d’écarter tout risque d’électrocution, garder le coffret fermé.
Ne confier l’entretien de l’appareil qu á un personnel qualifié.
VORSICHT
Um Feuergefahr und die Gefahr eines eiektrischen Schiages zu vermeiden, darf das Gerät weder Regen
noch Feuchtigkeit ausgesetzt werden.
Um einen elektrischen Schiag zu vermeiden, darf das Gehäuse richt geöffnet werden.
Überiassen Sie Wartungsarbeiten stets nur einem Fachmann.
B
Important Safety Instructions
1.
Read Instructions
All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future reference.
3. Heed Warnings
All warnings on the product and the operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub;
in a wet basement; or near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult and serious damage to the product. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the
product should follow the manufacturer's instructions, and should use a mounting accessory
recommended by the manufacturer.
9. Moving
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to
overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these openings must not be blocked or covered.
The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.
This product should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer's instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If
company. For products intended to operate from battery power, or other sources, refer to the operating
instructions.
12. Grounding or Polarization
This product is equipped with a three-wire grounding-type plug a plug having a third (grounding) pin. This
plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert
the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the grounding-type plug.
13. Power-Cord Protection
Power-supply cords should be routed to that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plug, convenience receptacles, and the point
where they exit from the product.
14. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet. This will prevent damage to the product due to
lightning and power-line surges.
15. Overloading
Do not overload wall outlets, extension cords or integral convenience receptacles as this can result in a
risk of fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the
product.
17. Inflammable and Explosive Substance
C
Avoid using this product where there are gases, and also where there are inflammable and explosive
substances in the immediate vicinity.
18. Heavy Shock or Vibration
When carrying this product around, do not subject the product to heavy shock or vibration.
19. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
20. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
a. When the power-supply cord or plug is damaged.
b. if liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance-this indicates a need for service.
21. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts
specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
22. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating condition.
23. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
24. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
D
Wichtige Sicherheitsanweisungen
1.
Alle Anweisungen lesen.
Vor Betrieb des Erzeugnisses sollten alle Sicherheits-und Bedienungsanleitungen gelesen werden.
2. Die Anweisungen aufbewahren.
Die Sicherheits-und Bedienungsanleitungen sollten fünftigen Bezug aufbewahrt werden.
3. Warnungen beachten.
Die Warnungen auf dem Erzeugnis und in den Bedienungsanleitungen solten beachtet werden.
4. Anweisungen befolgen.
Alle Bedienungsanleitung-und
Verwendungsanweisungen sollten befolgt werden.
5. Reinigung
Den Stecker des Geräts vor Reinigung aus der Steckdose ziehen. Keine flüssigen Reinigungsmittel oder
Aerosolreiniger verwenden. Zum Reinigen einen feuchten Lappen verwenden.
6. Zubehör
Nur vom-Hersteller des Erzeugnisses empfohlenes Zubehör verwenden, da es sonst zu Störungen
kommen kann.
7. Wasser und Feuchtigkeit
Dieses Erzeugnis nicht in der Nähe von Wasser verwenden - z.B, in der Nähe einer Badewanne, eines
Waschbeckens, einer Küchenspüle, eines Waschzubers, in einem nassen Keller, in der Nähe eines
Schwimmbeckens usw.
8. Aufstellung
Das Erzeugnis nicht auf einen unstabilen Wagen, Stand, Dreifuß, Träger oder Tisch stellen.
Das Erzeugnis kann sonst herunterfallen und ein kind oder einen Erwachsenen schwer verietzen.
Außerdem kann das Gerät schwer beschädigt werden. Nur mit einem Wagen, Stand, Dreifuß, Träger
oder Tisch verwenden, der vom Hersteller empfohlen oder mit dem Erzeugnis verkauft worden ist. Für
jegliche Anbringung sollten die Anweisungen des Herstellers befolgt werden, und das vom Hersteller
empfohlene Anbringungszubehör sollte verwendet werden.
9. Eine Kombination von Erzeugnis und Wagen sollte vorsichtig bewegt werden.
Schneller Halt, übermäßige Krafteinwirkung und unebene Oberflächen können Umkippen der kombination
von Erzeugnis und Wagen verursachen.
10. Ventilation
Schlitze und Öffnungen im Gehäuse dienen der Ventilation. Sie sind für zuverlässigen Betrieb des
Gerätes und Schutz vor Überhitzung erforderlich und dürfen nicht blockiert oder abgedeckt werden.
Die Öffnungen sollten niemals dadurch blockiert werden, daß, das Gerät auf ein Bett, ein Sofa, einen
Teppich oder eine ähnliche Oberfläche gestellt wird.
Das Gerät sollte nur dann in Einbauinstallierung wie in einem Bücherschrank oder einem Gestell
verwendet werden, wenn angemessene Ventilation vorgesehen ist bzw. Die Anweisungen des
Herstellers befolgt worden sind.
11. Stromversorgung
Dieses Erzeugnis sollte nur an der auf dem Typenschild angegebenen Stromversorgungsart betrieben
werden. Wenn Sie nicht sicher sind, was für eine Stromversorgung Sie haben, so wenden Sie sich bitte
an Ihren Erzeugnishändler oder an das lokale Elektrizitätswerk. Beziehen Sie sich für Batteriebetrieb
oder andere Stromquellen vorgesehene Erzeugnisse bitte auf die Bedienungsanleitungen.
12. Erdung oder Polarisierung
Dieses Erzeugnis ist mit einem Schutzkontaktstecker mit drei Leitern ausgerüstet, mit einem
Erdungskontakt. Dieser Stecker paßt nur in ein schuko-Steckdose. Dies ist eine Sicherheitsmaßnahme.
Wenn Sie den Stecker nicht in die Steckdose stecken können, so wenden Sie sich bitte an ihren Elektriker,
damit er die veraltete Schuts des Schutzkontaktsteckers unwirksam.
13. Netzkabelschutz
Netzkabel sollten so verlegt werden, deß möglichst nicht darauf getreten wird und daß sie nicht
eingeklemmt werden, mit besonderer Beachtung der kabel an Stackern, Verlängerungskabeln und dem
Austritt des Kabels aus dem Erzeugnis.
E
14. Blitzschlag
Für zusätzlichen Schutz des Erzeugnisses während eines Gewitters oder bei Nichtverwendung für lange
Zeit den Stecker aus der Steckdose ziehen. Dies verhütet Beschädigung durch Blitzschlag und
Netzspannungsstöße.
15. Überlastung
Wandsteckdosen, Verlängerungskabel und eingebaute Bequemlickkeitssteckdosen nicht überlasten, da
dies Feuer oder elektrischen Schlag verursachen kann.
16. Eindringen von Fremdkörpern und Flüssigkeit
Niemals Objekte irgendwelcher Art durch die Öffnungen in das Gerät schieben, da diese unter hoher
Spannung stehende Teile berühren oder kurzschließen können, wodurch es zu Feuer oder elektrischem
Schlag kommen kann. Niemals Flüssigkeiten irgendwelcher Art auf das Erzeugnis verschütten.
17. Entflammbare und explosive Substanzen
Vermeiden Sie Verwendung dieses Erzeugnisses an Orten mit Gasen bzw. entflammbaren oder
explosiven Substanzen in der direkten Umgebung.
18. Starke stöße oder Vibrationen
Setzen Sie das Erzeugnis beim Transport nicht starken Stößen oder Vibrationen aus.
19. Wartung
Versuchen Sie nicht, dieses Erzeugnis Selbst zu warten, da Sie sich durch Öffnen bzw. Entfernen von
Abdeckungen hohen Spannungen und sonstigen Gefährdungen ausserzen können.
Beziehen Sie sich für jegliche Wartung auf qualifiziertes Wartungspersonal.
20. Beschädigung, die Wartung erfordert
Ziehen Sie den Stecker dieses Erzeugnisses aus der Steckdose und wenden Sie sich an qualifiziertes
Wartungspersonal, wenn eine der folgenden Bedingungen vorliegt:
a. Wenn das Netzkabel oder der Stecker beschädigt ist.
b. Bei Eindringen von Flüssigkeit oder Fremdkörpern in das Gerät.
c. Wenn das Erzeugnis Regen oder Wasser ausgesetzt worden ist.
d. Wenn das Erzeugnis bei Befolgen der Bedienungsanleitungen nicht normal funktioniert.
Nur die Regelelemente verstellen, die in den Bedienungsanleitungen behandelt werden, da
unangemessene Einstellung anderer Regelelemente Beschädigung verursachen kann und oft
beträchtliche Arbeit durch einen qualifizierten Techniker erfordert, um das Erzeugnis wieder, zu normalem
Betrieb zurückzubringen.
e. Wenn das Erzeugnis fallen gelassen oder beschädigt worden ist.
f. Wenn das Erzeugnis eine klare Änderung in der Leistung zeigt-dies weist darauf hin, daß Wartung
erforderlich ist.
21. Ersatzteile
Wenn Ersatzteile erforderlich sind, darauf achten, daß der Wartungstechniker nur die vom Hersteller
festgelegten Ersatzteile oder Teile mit den gleichen Charakteristiken wie die ursprünglichen Teile
verwendet. Unautorisierte Ersatzteile können Feuer, elektrischen Schlag oder sonstige Gefährdungen
verursachen.
22. Sicherheitsprüfung
Bitten Sie den Wartungstechniker nach der Vollendung von Wartung oder Reparaturarbeiten an diesem
Erzeugnis um die Durchführung von Sicherheitsprüfungen, um zu bestimmen, daß das Erzeugnis im
angemissenen Betriebszustand ist.
23. Anbringung an der Wand oder an der Decke
Das Erzeugnis sollte nur entsprechend den Empfehlungen des Herstellers an einer Wand oder an der
Decke angebracht werden.
24. Wärme
Das Erzeugnis sollte fern von Wärmequellen wie Radiatoren, Heizwiderständen, Öfen und anderen
Wärme erzeugenden Erzeugnissen (einschließlich Verstärkern) aufgestellt werden.
F
Mises en Garde Importantes
1.
Lire les instructions
Lire toutes les instructions de sécurité et de fonctionnement avant de faire fonctionner l’appareil.
2. Conserver ces instructions
Conserver les instructions de sécurité et de fonctionnement á des fins de référence ultérieure.
3. Tenir compte des avertissements
Tous les avertissements qui figurent sur l’appareil et dans le mode d’emploi devront être respectés.
4. Observer les instructions
Observer toutes les instructions de fonctionnement et d’utilisation.
5. Nettoyage
Avant de procéder au nettoyage, débrancher l’appareil de la prise secteur. Ne pas utiliser de produits de
nettoyage liquides ou en aérosol.
Nettoyer l’appareil avec un chiffon humide.
6. Fixations
Ne pas utiliser de fixations non recommandées par le fabricant de l’appareil car elles pourraient être
source de danger.
7. Eau et humidité
Ne pas utiliser l’appareil á proximité d’eau-par exemple prés d’une baignoire, d’un lavabo, d’un évier ou
d’un bac á lessive, dans un sous-sol humide, ou prés d’une piscine, etc.
8. Accessoires
Ne pas placer l’appareil sur un chariot, un socle, un pied, un support ou one table instables L’appareil
pourrait tomber, blessant griévement des enfants ou des adultes, et étant sérieusement endommagé.
Utiliser exclusivement le chariot, le socle, le pied, le support ou la table recommandés par le fabricant, ou
vendus avec l’appareil. Pour tout montage de l’appareil, respecter les instructions du fabricant, et utiliser
á cette fin l’accessoire de montage recommandé par le fabricant.
9. L’appareil monté sur son chariot devra être déplacé avec précaution.
Des arrêts brusques, une force excessive et des surfaces irréguliéres pourraient provoquer le
renversement de l’ensemble appareil-chariot.
10. Ventilation
Les fentes et les ouvertures du coffret sont prévues pour la ventilation ainsi que pour garantir un
fonctionnement en toute sécurité de l’appareil et le protéger de toute surchauffe, et ces ouvertures ne
devront donc être ni obstruées ni recouvertes. Ne jamais obstruer les ouvertures en plaçant l’appareil sur
un lit, un sofa, un tapis ou toute surface similaire. Ne jamais placer l’appareil dans un support confiné,
par exemple une bibliothèque ou une é tagé re, sans ventilation suffisante ou sans respecter les
instructions du fabricant.
11. Sources d’allmentation
L’appareil devra être alimenté exclusivement sur le type d’alimentation indiqué sur l’étiquette signalétique.
Sil’ on n’est pas sûr du type d’alimentatio du local, consulter le revendeur de l’appareil ou la compagnie
d’électricité locale. Pour les appareils qui fonctionnent sur batterie ou sur d’autres sources, voir le mode
d’emploi.
12. Mise á la terre ou polarisation
L’appareil est doté d’une fiche trifilaire avec mise á la terre, dont la troisiéme broche assure la mise á la
terre. Cette fiche ne rentrera que dans les prises trifilaires de mise á la terre. Ceci est une mesure de
sécurité. Si la fiche ne rentre pas dans la prise, faire remplacer la prise désuéte par un électricien.
Ne pas rendre vaine la measure de sécurité assurée par cette prise avec mise á la terre.
13. Protection du cordon d’alimentation
Acheminer les cordons d’alimentation de facon qu’on ne risque pas de marcher dessus ou de les coincer
sous un objet placé dessus ou contre eux.
Faire particulièrement attention aux fiches des cordons, á la proximité des prises, et á l’endroit oú ils
ressortent de l’appareil.
14. Foudre
Pour renforcer la protection de l’appareil pendant un orage, ou si l’on s’en éloigne ou qu’on reste
longtemps sans l’utiliser, le débrancher de la source d’alimentation. Ceci permettra d’éviter tout
dommage de l’appareil dú á la foudre et aux surtensions de ligne.
15. Surcharge
Ne pas surcharger les prises, rallonges et prises multiples car cela pourrait entraîner un risque de feu ou
de choc électrique.
G
16. Pénétration d’objets et de liquides
Ne jamais enfoncer d’objets d’aucune sorte dans les ouvertures de l’appareil car ils pourraient toucher des
points de tension dangereuse ou court-circuiter des piéces, ce qui pourrait provoquer un feu ou un choc
électrique. Ne jamais renverser de liquide d’aucune sorte sur l’appareil.
17. Substances inflammabes et explosives
Eviter d’utiliser l’appareil en présence de gaz, ainsi qu’á proximité immédiate de substances inflammables
et explosives.
18. Chocs ou vibrations violents
Lorsqu’on transporte l’appareil, ne pas le soumettre á des chocs ou des vibrations violents.
19. Réparations
Ne pas tenter de réparer l’aapareil soi-même car le fait d’ouvrir ou de retirer les caches risque d’exposer
l’utilisateur á des tensions dangereuses notamment. Confier toute réparation á un personnel qualifié.
20. Dommages nécessitant réparations
Débrancher l’appareil de la source d’alimentation et confier les réparations á un personnel qualifié dans
les cas suivants:
a. Lorsque le cordon d’alimentation ou sa fiche sont endommagés
b. Si du liquide s’est renversé sur l’appareil ou que des objets sont tombés dedans
c. Si l’appareil a été exposé á la pluie ou á l’eau.
d. Si l’appareil ne fonctionne pas normalement lorsqu’on observe les instructions d’utilisation.
Ne régler que les commandes couvertes par le mode d’emploi ; en effet, un réglage incorrect des autres
commandes pourrait entrainer des dommages et nécessiteront souvent des travaux de réparation coûteux
par un technicien qualifié pour remettre l’appareil en état de marche.
e. Si l’appareil est tombé ou qu’il a été endommagé.
f. Si l’appareil affiche une nette modification de ses performances, cela signifie qu’il a besoin d’être
réparé.
21. Piéces de rechange
Si l’on a besoin de piéces de rechange, veiller á ce que le technicien de réparation utilise exclusivement
les piéces de rechange spécifiées par le fabricant ou des piéces ayant les mêmes caractéristiques que les
piéces d’origine. Les piéces de rechange non autorisées risquent de provoquer un feu, un choc
électrique et autres dangers.
22. Vérificaton de sécurité
Aprés tout travail d’entretien ou de réparation de l’appareil, demander au technicien de réparation
d’effectuer les vérifications de sécurité pour s’assurer que l’appareil est en bon état de marche.
23. Montage au mur ou au plafond
L’appareil ne pourra être monté au mur ou au plafond que de la maniére recommandée par le fabricant.
24. Chaleur
Eloigner l’appareil des sources de chaleur, telles que radiateurs, appareils de chauffage, cuisiniéres, et de
tour produit engendrant de la chaleur (y compris les amplificateurs).
H
IMPORTANT NOTICE
For USA
These products have been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this product in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at his
own expense.
WARNING
Changes or modifications not expressly approved by Hitachi Kokusai Electric responsible for compliance could
void the user’s authority to operate the equipment.
For Canada
This product does not exceed the class A/class B limits for radio noise emissions from digital apparatus as set
out in the radio interference regulations.
Le présent appareil n’émet pas de bruits radioélectriques dépassant les limités applicable aux appareils
numériques de classe A prescrites dans le rVglement sur le brouillage radioélectrique édicter par le ministére
des communications du canada.
I
Contents
Safety Instructions .................................................................................................................................. B
Important Safety Instructions.................................................................................................................. C
Wichtige Sicherheitsanweisungen ......................................................................................................... E
Mises en Garde Importantes .................................................................................................................. G
IMPORTANT NOTICE ............................................................................................................................. I
Contents ................................................................................................................................................ 10
Introduction............................................................................................................................................ 11
Facility names & Functions ................................................................................................................... 12
Features & Functions ............................................................................................................................ 13
Specifications ........................................................................................................................................ 14
JU-1000 Connection Diagram ............................................................................................................... 15
Gateway PC Software Installation ......................................................................................................... 16
CCU - CU-HD1000-S5 Network Settings .............................................................................................. 17
Resetting the CCU IP Address .............................................................................................................. 21
Gateway PC program install & setup .................................................................................................... 26
IP Control System - Setting screen ....................................................................................................... 27
IP Control System - Control screen ....................................................................................................... 29
Notes about IP Control System ............................................................................................................. 31
General Troubleshooting ....................................................................................................................... 32
- 10 -
Introduction
1. General
This system provides remote control of Hitachi HDTV production cameras via a customer
provided data network. The expanded camera IP control system consists primarily of the
data multiplexer/ serializer unit JU-1000. This unit is configured and controlled via the
customer provided gateway PC via USB cable as shown below.
The gateway PC provides the network access via standard TCP/IP for the remote control of
the camera CCUs.
Customer Provided
Dedicated LAN
IP Control System
Camera Head
S K -HD1000
Joint Unit
RU-3400JY
JU-1000
( 8unit Max)
Fiber Cable
USB Cable
Network HUB
Network HUB
Camera Control Unit
CU-H D 1000
Network Cable
Network Cable
Camera Head
Procotol ConverTer Soft(*3)
Installation
S K -HD1000
Fiber Cable
Procotol Converter Soft(*3) : Procotol Converter AND Switcher
Camera Control Unit
CU-H D 1000
Network Cable
2. Features
(1) The HDTV camera remote control is provided via TCP/IP as follows:
 The control panel junction unit model JU-1000 is configured and controlled via HITACHI
provided software using a standard PC.
 A standard USB port is used as the connection between the PC and the JU-1000.
 Eight (8) camera remote control panels can be directly connected to the JU-1000.
(2) Power supply details of the JU-1000
 The USB port provided on the JU-1000 uses the 5VDC provided via the USB port PC
voltage supply.
 Power for up to eight (8) remote control panels is provided by the externally provided
HITACHI power supply.
- 11 -
Facility names & Functions
FRONT VIEW
A1
REAR VIEW
A5
A4
A2
A3
A1
POWER SW
A2
DC POWER INPUT (Adaptor connection)
A3
REMOTE INPUT CONNECTOR (Remote cable connection)
A4
USB2.0 (USB cable connection)
A5
JU-1000 LABEL
- 12 -
Features & Functions
Function
(1) Remote control panel connections:

RU-3400JY (X8)
(2) POWER ON/OFF (Front panel side)

The front panel POWER SWITCH turns on/off the remote control panels connected.

The POWER SWITCH illuminates green when power is ON.
(3) Remote control panel power supply

DC13.8V is supplied with the supplied external AC adaptor.
(4) USB Port power supply

DC5V 500mA MAX is supplied from the connected personal computer.
(5) Physical Interface (JU-1000 rear panel)

USB2.0 X1: port (Type A) for PC serial data connection.
Accessory: USB cable 3m for connection of JU-1000 and personal computer
(Type A to A).

AC adapter X1: connector (HA16RA-4P:HIROSE)

Accessory: External Power Supply (IA-200a) with 2 meter DC cable.

RU Remote control connector X8 (HR10A-7R-4SC:HIROSE)

Labeling RU1 ~ RU8 (Eight positions).

Maximum cable distance to RU: 10 meter
- 13 -
Specifications
(1) Dimensions (WxDxH):
320 x 320 x 88mm
(2) Mass:
4Kg.
(3) AC Adapter Power input:
AC100~240V 50/60Hz
(4) Power consumption:
60W max. w/ (RU-3400 x 8)
(5) USB Supplied electricity:
DC5V 500mA (2.5W) Max.
(6) Ambient temperature:
0 to +40 C
o
Dimensions
(All units in mm)
- 14 -
JU-1000 Connection Diagram
■ JU-1000: Cable connection diagram
RU-3400 x 8 MAX
Gateway PC
REMOTE CABLE
L=10m
AC100~ 240V( 50/60Hz)
ADAPTOR CABLE
L=1.8m
IA-200
RU8
RU7
DC INPUT
RU6
RU5
RU4
RU3
RU2
RU1
JU-1000
AC ADAPTOR
DC CABLE
L=2.0m
RU-3400
POWER SW
■ Accessories parts list
PARTS
NAME
Net
AC ADAPTOR
ADAPTOR CABLE
DC CABLE
USB CABLE
DRIVER CD-ROM
SOFT CD-ROM
IA-200a
Accessories (IA-200a)
DC-S2
KB-USB-A3K
Communication Product Driver (Quatech)
IP Control Soft CD-ROM (HITACHI)
- 15 -
1
1
1
1
1
1
USB
USB CABLE
(L=3m)
Gateway PC Software Installation
1. In order for the gateway PC to configure and control the RU-3400JY-S11 connected to the
JU-1000, it is necessary to install the HITACHI provided software.
USB Cable
Junction Unit
JU-1000
Gateway PC
IP Control application software installation
2. Driver installation on PC
a. Connect the JU-1000 to the PC via USB cable.
RU-3400JY-S11 at this time.
It is not necessary to connect the
b. Insert the CD-ROM disc labeled “QUATECH Communication Product Drivers and
Manuals” in the PC’s CD/DVD drive. Follow the instructions on the PC for the
installation of the drivers.
c.
When the installation is completed remove the CD-ROM disc in step b above from the
PC’s optical drive.
d. Verify the drivers have been properly installed by: "My computer" →"Property"
→"Hardware" →"Device manager" select and expand the "Port (COM & LPT)”, the
eight (8) new USB ports for the JU-1000 should exist as shown below.
e. When connecting and disconnecting the JU-1000 from the PC’s USB port, ALWAYS
verify that these com ports are open and available for use.
(Please document the COM PORT NUMBERS shown in the window below since
they are needed for TCP/IP address assignment in later steps.)
COM Port x8
Addition
- 16 -
CCU - CU-HD1000-S5 Network Settings
The network IP address can be set by connecting a CROSSED RJ45 network cable
(crossed-cable) between a PC and the CU-HD1000-S5. The PC requires the HITACHI
provided software in order to communicate via the CU-HD1000-S5’s RJ45 port.
Camera Control Unit
CU-HD1000
Crossed Network Cable
← IP Address Set
DeviceInstaller(Lantronix)
Installation PC
a. XPORT web server device installation
 NOTE: Microsoft .NET Framework 2.0 or greater must be installed on
the PC beforehand
b. Insert the HITACHI provided CD-R disc labeled “IP Control Soft CD-ROM” into the
optical drive of your PC and look for the file name “Di32DL_4.2.0.3_Web.exe”The PC
does not have to be connected to the CU-HD1000-S5 at this time.
c.
Double click to install and follow the instructions on the screen to install the program
on the PC.
- 17 -
1.) Please set or change the TCP/IP protocol properties of the PC to “Obtain an IP address
automatically” because the IP Address initialization of CU-HD1000-S5 is an automatic
acquisition mode.
2.) Connect the CU-HD1000-S5 to the PC as shown in the above figure. Execute the Lantronix
DeviceInstaller application by START > ALL PROGRAMS > LANTRONIX > DeviceInstaller
4.2 > DeviceInstaller.
3.) Click on "Search" to display the current IP Address of the connected CU-HD1000-S5.
right pane will show the CU-1000 TCP/IP Network Settings.
- 18 -
The
4.) If the IP Address of the CU-HD1000-S5 is highlighted, and the "Home" button on the screen is
clicked, the Network Settings are displayed on the right pane of the DeviceInstaller program.
Note that only the IP Address can be changed on the Network Settings pane. When it is
necessary to change the port number of the CCU, click on the “Serial Settings” under Channel
1 on the Network Settings pane.
5.) Click on “OK” on the right pane then on “Apply Settings” on the left pane to change the IP
address.
6.) Confirm that the IP Address has been changed by re-starting the " DeviceInstaller " program
again by clicking on “Search ". The IP Address on the PC side should also change when
retrieving it.
- 19 -
7.) When CU-HD1000-S5 is changed to arbitrary [IP Address], [Subnet Mask], and [Default
Gateway], and the address is retrieved, it is necessary to match IP Address of PC, Subnet
Mask, and Default Gateway.
(Enough operational administrative to IP Address etc.)
- 20 -
Resetting the CCU IP Address
In the case of emergency when the CCU device is not displayed on the DeviceInstaller application
screen or you forgot the IP address necessary to access the CU-HD1000-S5 by the following
procedure to reset the IP address.
Requirements

"CU-HD1000-S5 MAC ADDRESS SHEET" initially attached on the CU-HD1000-S5 CCU.

Personal Computer for maintenance with installed Microsoft Windows XP SP2 (or greater)
Operation System and Microsoft Netframework 2.0 (or greater).

Crossed-type LAN (RJ45) cable.

IP address number to reset the CCU (CU-HD1000-S5) as provided by your network
administrator..
In this example, we use following address as re-setting IP address
[IP address: 172.16.0.11]
[Subnet Mask: 255.255.0.0]
[Default Gateway: 172.16.0.1]
1) Check MAC Address of CCU
Check the serial number of CCU to read out MAC address on "CU-HD1000-S5 MAC
ADDRESS SHEET".
In this example, we use the following MAC address
[MAC Address : 00-20-4a-95-18-84]
2) Define IP Address for the maintenance PC
We recommend using the IP address of the Default Gateway or any IP addresses that is
available and able to communicate with the IP address to be reset.
3) Connect the maintenance PC and CCU with a crossed- type LAN cable.
4) Start up the command prompt
Start up the command prompt program pre-installed on the Windows.
"START" -> "PROGRAM" -> "ACCESSORIES" -> "COMMAND PROMPT"
5) Register the ARP cache
Register the MAC address on the ARP table of the maintenance PC.
Command: arp -s <IP Address> <MAC Address>
Example PC screen display:
C:\Documents and Settings\Administrator>arp -s 172.16.0.11 00-20-4a-95-18-84
6) Check the ARP cache.
Confirm the ARP cache has been correctly registered on the maintenance PC.
Command : arp -a
- 21 -
Example PC screen display:
C:\Documents and Settings\Administrator>arp -a
Interface: 192.168.0.99 --- 0x2
Internet Address
Physical Address
Type
172.16.0.11
00-20-4a-95-18-84
static
7) Execute the Telnet command (1)
Try to access the IP address by the Telnet command with the port number "1".
NOTICE: Be sure to use the port number "1" although port number is typically used as
Telnet. It is the proper action for the next step although the telnet connection will fail.
Command: telnet <IP address> <PortNumber>
Example PC screen display:
C: \Documents and Settings\Administrator>telnet 172.16.0.11 1
8) Execute the Telnet command (2)
Next, access desired IP address by the telnet command with port number "9999".
NOTICE: When the command is correctly entered, the message "Press Enter for Setup
Mode" appears.
Press the "ENTER" key within 5 seconds to avoid the timeout of this prompt. When the
command is accepted, the following example screen is displayed on the PC.
*You can check current IP address.
*In case of time-out, start from 7) again.
Command : telnet <IP address> <PortNumber>
Example PC screen display:
C: \Documents and Settings\Administrator>
C: \Documents and Settings\Administrator>telnet 172.16.0.11
9999
MAC address 00204A951884
Software version V6.1.0.0 (051122) XPTEXE
Press Enter for Setup Mode
- 22 -
*** basic parameters
Hardware: Ethernet TPI
IP addr 192.168.0.21, no gateway set,netmask 255.255.255.0
*** Security
SNMP is enabled
Change Setup:
0 Server
1 Channel 1
3 E-mail
5 Expert
6 Security
7 Defaults
8 Exit without save
9 Save and exit
Your choice ?
9) Reset the IP address
Select the “0” Server, and reset IP address following the direction on the screen.
NOTICE:
The Netmask setting specifies the bit length used for the host addressing.
Example:
When the netmask setting is 255.0.0.0, the host addressing uses 24 bits.
When the netmask setting is 255.255.0.0, the host addressing uses 16 bits.
When the netmask setting is 255.255.255.0, the host addressing uses 8 bits.
NOTICE:
Never change the password for telnet.
Controlling this password is your responsibility.
- 23 -
Example PC screen display:
Change Setup:
0 Server
1 Channel 1
3 E-mail
5 Expert
6 Security
7 Defaults
8 Exit without save
9 Save and exit
Your choice? 0
IP Address : (192) 172.(168) 16.(000) 0.(021) 11
Set Gateway IP Address (N) ? Y
Gateway IP addr (000) 172.(000) 16.(000) 0.(000) 1
Netmask: Number of Bits for Host Part (0=default) (8) 16
Change telnet config password (N) ? N
10) Save the setting and Exit
Choose “9 Save and exit”.
Example PC screen display:
Change Setup:
0 Server
1 Channel 1
3 E-mail
5 Expert
6 Security
7 Defaults
8 Exit without save
9 Save and exit
Your choice? 9
Parameters stored...
11) Verify the connection
Verify the reset IP address is correct.
Command: ping <IP address>
- 24 -
Example PC screen display:
C:\Documents and Settings\Administrator>ping 172.16.0.11
Pinging 172.16.0.11 with 32 byte of data:
Reply from 172.16.0.11:bytes=32 time=0ms TTL=125
Reply from 172.16.0.11:bytes=32 time=0ms TTL=125
Reply from 172.16.0.11:bytes=32 time=0ms TTL=125
Reply from 172.16.0.11:bytes=32 time=0ms TTL=125
Ping statistics for 172.16.0.11:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
This is the end of the procedure for recovering the CU-HD1000-S5’s IP ADDRESS
- 25 -
Gateway PC program install & setup
1.) Installation
Copy the HITACHI “CTVIPcontrolSystem” Folder onto an arbitrary drive/folder.
The main application is registered to the STARTUP menu group after installation.
2.) File Configuration
IPCSYS.exe
CTVIPControlSystem.ini
CTVIPControlSystem.dat
LOG Folder
Main Application
Initialization File
Internal Data (Please do not delete it)
Communication Log
3.) Initialization File
[Socket]
connect_wait_time = 100
recv_retry_timeout = 10
recv_wait_time = 10
[Serial]
recv_retry_timeout = 10
4.) Log File
File name
IPCONTROL_
1_
=
=
=
socket connection timeout [msec]
received retry interval [msec]
received wait timeout [msec]
received retry timeout [msec]
IPCONTROL_1_20091003.log
fixed
RU’s number (1 ~ 8)
Configuration
2001, 2009-10-0317:37:19.761168,[CNTL ←CUCU], message box
1
2
3
4
1
2
3
Starting from number 1000, 1001 ~ 1008 indicate the transmission with RU.
Starting from number 2000, 2001 ~ 2008 indicate the transmission with CCU.
Record date the decimal point is μSec.
Transmission Direction
CNTL expresses the main system.
CUCU stand for CCU,
RURU stand for RU
CNTL → RURU transmitting from PC to RU
CNTL ← RURU receiving from PC to RU
CNTL → CUCU transmitting from PC to CCU
CNTL ← CUCU receiving from PC to CCU
4 Message box
Transmission data display HEX and ASCII array, string length.
The others display message.
(Example)
Socket Connect Success [192.168.0.2:10001] = Connect Success
Serial Connect Success [9600, n, 8, 1] = Connect Success
Serial Disconnect Success = Disconnect Success
- 26 -
IP Control System - Setting screen
14
2
3
1
5
6
4
7
8
9
12
10
13
11
1 RU Protocol: The setting of the communication of RU is shown.(not available for the setting
changed).
2 CU Protocol: The setting of the communication of CU is shown.(not available for the setting
changed).
3 Sequence: When the communication log data is preserved, the check is put and SAVE is
selected. Since the log data preservation becomes load, we recommend you not to normal operation.
4
RU Setting – Use: Check RU of the camera system that controls IP.
5 RU Setting – Name: An arbitrary name is input to RU on the IP control side.
reflected it in the Control screen.)
6
(It is automatically
RU Setting – Port No.: "My computer" →"Property" →"Hardware" →"Device manager" →"Port"
The port number displayed here is input to“01.-08.“ of the IP Control screen in numerical order.
(Refer to Gateway PC Software Installation on Page-16)
7
CCU Setting – Name: Enter an arbitrarily name of CCU.
8
CCU Setting – IP: IP Address individually set to CCU is input.
- 27 -
(Refer to CCU - CU-HD1000-S5 NETWORK SETTINGS on page 17)
9 CCU Setting – Port No.: The port number set to CCU is input. (The setting when the factory is
shipped is 10001. )
10
Camera Setting – Name: Enter an arbitrarily name of Camera.
(It is automatically reflect it in the Control screen.)
11 Camera Setting – CCU: The name of CCU entered at
combination with the camera of 10 is displayed.
7
is automatically reflected, and the
While Off Line the combination of CCU can be changed from the pull-down tab.
(Item managed when combination of CCU and camera is physically changed)
(While off line cannot be changed.)
12
Cancel: The setting changed on the Setting screen is canceled.
13
Save: When the setting changed on the screen is executed or is preserved, click ”save” button.
14
Control / Setting: Switch tab on Control screen and Setting screen.
- 28 -
IP Control System - Control screen
2
3
4
1
5
6
8
7
9
10
1
RU Action
 ON Line ---------- Transmission status (Lit Blue)
 OFF Line --------- Non-transmission status (Lit Red)
 Taken Off -------- Deactivates the RU
2
RU Name
The User-programmable name for the RU connected.
(Provide a description that corresponds with the camera controlled by the RU.)
3
Camera Name
The User-programmable name for the Camera connected.
(Provide a description that corresponds with RU controlling this camera)
4
RU Status
 CON -------------- ERR -------------- RX ---------------- TX -----------------
Status of the RU communication (blue flashing)
RU abnormal connection (red flashing or steady)
RU is being received (blue flashing).
RU is being transmitted (blue flashing).
- 29 -
5
CCU Status
 CON -------------- ERR -------------- RX ---------------- TX -----------------
Status of the CCU communication (blue flashing)
CCU abnormal connection (red flashing or steady)
CCU is being received (blue flashing).
CCU is being transmitted (blue flashing).
6
RU Call
 Call is being received from the RU (red flashing or steady).
 Call of RU responds when C on the RU side of the Control screen is pushed (red steady +
Call sound).
7
CCU Call
 Call of CCU or the camera is received (red flashing or steady).
 Call of CCU and the camera responds when C on the CCU side of the Control screen is
pushed. (red steady + Call sound).
8
RU Progress Bar
The quantity of the data transmission buffer from PC to RU is displayed (blue gauge linear
display).
(A high PC CPU load causes data rate increase. There is a possibility that interference may
occur when the buffer and data transmission indicated becomes more than the half on the
blue linear display.)
9
CCU Progress Bar
The quantity of the data transmission buffer from PC to CCU is displayed (blue gauge linear
display).
(A high PC CPU load causes data rate increase. There is a possibility that interference may
occur when the buffer and data transmission indicated becomes more than the half on the
blue linear display.)
10
Camera Name Change
Only in the OFFLINE MODE; the camera can be selected from the pull-down menu and the
combination of RU and the CCU camera be changed.
(It is not possible to change in the OnLine operation state.)
- 30 -
Notes about IP Control System
1) Follow these instructions when starting the remote IP control system.
 Execute the program “IPCSYS exe” Start (OffLine Mode) → JU-1000 Power ON → Control
screen (ONLINE)
 Attention: When JU-1000 is started in the state of ON Line, the RU3400 on the IP side might
automatically acquire the operation priority.
 (Please begin from the state of OFFLINE when operating it.)
2) Do not remove the USB cable between JU-1000 and PC while they are live and communicating.
 If the USB cable comes loose or falls off the PC; close the “IPCSYS exe” program, insert the
USB cable, and re-open the “IPCSYS exe”.
(If the USB cable is disconnected, the control remains active on the RU-3400’s connected on
the CCU/ camera side.)
 Confirm that the PC recognizes the (8) eight COMM ports by "Port" on "Device Manager".
(Refer to 5-1)
NOTE: When “!” mark is displayed in each port, the port is not recognized.
3) Do not remove the network cable between PC<->CCU while they are live and communicating.
 The communication resets automatically when the cable is reconnected.
 When the cable is disconnected, ERR on the CCU side lights red.
 (Even when the network cable comes off, the control is possible on the camera system side.)
4) Do not remove the remote cable of RU while they are live and communicating.
 The communication resets automatically when the cable is reconnected.
 When the cable has come off, ERR on the RU side lights red.
 (Even when a remote cable comes off, the control is possible on the camera system side.)
5) Do not turn off the power supply (AC adaptor) of the JU-1000 while the system is online and
communicating.
 Upon restoring power; the JU-1000 becomes active and the communication is reestablished.
 ERR on the RU side lights red in the state of power supply OFF.
 (The control is possible even in the state of power supply OFF on the camera system side.)
6) Do not turn off the power supply of the PC while the system is live and communicating.
 When the power supply of the PC is restored, and IPCSYS exe program is opened again. Start
→JU-1000 Power ON re-setup.
 (Even when the power supply of PC fails, the control is possible on the camera system side.)
7) Do not end the Control Screen while communicating.
 The program, IPCSYS.exe will stop transmitting, (controlling traffic) and upon re-execution it
returns. Start →JU-1000 Power ON re-setup.
 (Even when the Microsoft Windows XP OS shuts down, the control is possible on the camera
system side.)
- 31 -
General Troubleshooting
The following is a brief list of Troubleshooting procedures in the case of problems during normal and
routine operation.
TROUBLE:
ACTION:
The RU’s connected to the JU-1000 suddenly stopped working but have power.
Check and assure that the IP Network Software is up and running.
TROUBLE:
The RU’s connected to the JU-1000 stopped working and all lamps are
extinguished.
Check the JU-1000 front panel POWER SWITCH. It should be lit and in the ON
position.
Check the EXTERNAL power supply that feeds 12VDC to the JU-1000. It should
be ON and its power switch illuminated. Check AC mains and replace AC LINE
FUSE if necessary.
ACTION:
TROUBLE:
ACTION:
One of the RU’s connected to the JU-1000 does not work.
Check to see if it is in OFFLINE mode.
Check to see if there is an ERROR light on.
Check to see if the camera head has control (camera TAKEN mode).
Troubleshooting items during the change of IP address on the CU-HD1000-S5
TROUBLE:
ACTION:
The CU-HD1000-S5 does not show in the [DeviceInstaller] program right pane.
Check the CCU presence using “LAN Cross Cable” connected directly to the PC.
Check that the CCU Power is ON.
Check the SUBNET MASK of the CCU and make sure it is the same as the PC’s.
TROUBLE:
ACTION:
The CCU forgets its IP address after setting or power cycle.
Need to set the ARP (Address Resolution Protocol) of MAC Address/ IP Address in
the CCU (CU-HD1000-S5). (See the X-Port operation manual)
Troubleshooting items in the IP Control Screen
TROUBLE:
ACTION:
The CCU side ERR light is illuminated Red.
Check to see if there is power supplied to the CCU.
Check to see if the network cable of the CCU is connected?
Check to see if the IP Address of the CCU is correctly set?
Refer to XX and XX
TROUBLE:
ACTION:
The RU side ERR is illuminated Red.
Check to see that there is a power supply connected to the JU-1000?
Refer to 7-6(5)
Check to see if the RU cable connected?
Check the setting of the port number on the Setting screen that corresponds to the
PC recognizes corresponding.
TROUBLE:
ACTION:
The RU operation doesn't react and ERR is unlit.
Check the USB cable between PC<>JU-1000 so that it is connected.
TROUBLE:
ACTION:
The screen of IP Control System is not displayed
Do not minimize it to the Windows Task Bar. Keep program running on top.
- 32 -
TROUBLE:
ACTION:
The application fails to start
When the gauge of the quantity of the transmission buffer is filled; there is a
possibility that abnormality is found in the network line. There is a possibility that
the load hangs to CPU data processing of PC.
Close all other running applications on the PC when the IPCSYS.EXE program is
running
TROUBLE:
ACTION:
Communication fails although the IP address is correct.
If the port number of CCU is not changed according to the kind of the network line,
it is likely not to communicate.
In this case, please confirm the port number that the network manager assigns.
It is necessary to change the CCU port number on the Setting screen.
It is necessary to change the port number of CCU.
(Please inquire of HITACHI when the trouble is not canceled for the
above-mentioned problem.)
- 33 -
Download PDF

advertising