Operating and installation instructions Cooker hood - S-bol

Operating and installation instructions
Cooker hood
To prevent the risk of accidents or damage to the appliance, it is
essential to read these instructions before it is installed and used for
the first time.
en-GB
M.-Nr. 10 093 460
Contents
Warning and Safety instructions .......................................................................... 4
Caring for the environment ................................................................................. 13
Guide to the appliance......................................................................................... 14
Modes of operation.............................................................................................. 16
Operation .............................................................................................................. 17
Switching the fan on .............................................................................................. 17
Fan run-on after cooking........................................................................................ 17
Switching the fan off .............................................................................................. 17
Switching the hob lighting on/off ........................................................................... 17
Energy saving tips................................................................................................ 18
Cleaning and care ................................................................................................ 19
Casing .................................................................................................................... 19
Grease filter............................................................................................................ 20
Charcoal filter......................................................................................................... 22
Disposing of the charcoal filter ......................................................................... 22
Changing a halogen lamp ...................................................................................... 23
After Sales / Guarantee ....................................................................................... 24
Position of the data plate ....................................................................................... 24
Installation ............................................................................................................ 25
Before installation .................................................................................................. 25
Assembly parts ...................................................................................................... 26
Appliance dimensions............................................................................................ 28
Safety distance between hob and cooker hood (S)............................................... 29
Installation recommendations................................................................................ 30
Attaching the front panel........................................................................................ 35
Aligning the deflector plate .................................................................................... 35
Fitting the grease filter ........................................................................................... 36
Exhaust socket ...................................................................................................... 36
Setting up for recirculation mode .......................................................................... 37
Electrical connection.............................................................................................. 38
Electrical connection ........................................................................................... 39
Connection for air extraction .............................................................................. 40
Condensate trap .................................................................................................... 41
Silencer .................................................................................................................. 41
2
Contents
Technical data ...................................................................................................... 43
3
Warning and Safety instructions
This appliance complies with all relevant local and national safety
requirements. Inappropriate use can, however, lead to personal
injury and damage to property.
To avoid the risk of accidents and damage to the appliance,
please read these instructions carefully before using it for the first
time. They contain important notes on the safety, installation, use
and maintenance of the appliance. Miele cannot be held liable for
non-compliance with these instructions.
Keep these instructions in a safe place and ensure that all users
are familiar with the contents. Pass them on to any future owner of
the appliance.
Correct application
 This cooker hood is intended for use in domestic households and
similar working and residential environments.
 The cooker hood is not intended for outdoor use.
 It must only be used as a domestic appliance to extract vapours
and remove odours from cooking.
Any other usage is not supported by the manufacturer and could be
dangerous.
 Where a recirculation cooker hood is fitted above a gas hob,
please ensure that there is an adequate supply of fresh air into the
room in which it is installed. Please seek the advice of a qualified
gas fitter (e.g. GasSafe in the UK) if necessary.
4
Warning and Safety instructions
 The cooker hood can only be used by people with reduced
physical, sensory or mental capabilities, or lack of experience and
knowledge, if they are supervised whilst using it, or have been
shown how to use it in a safe way and recognise and understand the
consequences of incorrect operation.
Safety with children
 Children under 8 years of age must be kept away from the cooker
hood unless they are constantly supervised.
 Children 8 years and older may only use the cooker hood
unsupervised if they have been shown how to use it safely and
recognise and understand the consequences of incorrect operation.
 Children must not be allowed to clean or maintain the cooker
hood unsupervised.
 Please supervise children in the vicinity of the cooker hood and
do not let them play with it.
 Danger of suffocation. Packaging, e.g. plastic wrappings, must be
kept out of the reach of babies and children. Whilst playing, children
could become entangled in packaging or pull it over their head and
suffocate.
5
Warning and Safety instructions
Technical safety
 Unauthorised installation, maintenance and repairs can cause
considerable danger for the user. Installation, maintenance and
repairs must only be carried out by a Miele authorised technician.
 A damaged appliance can be dangerous. Check it for visible signs
of damage. Do not use a damaged appliance.
 The electrical safety of this appliance can only be guaranteed
when correctly earthed. It is essential that this standard safety
requirement is met. If in any doubt please have the electrical
installation tested by a qualified electrician.
 Reliable and safe operation of this cooker hood can only be
assured if it has been connected to the mains electricity supply.
 Before connecting the appliance to the mains supply, ensure that
the connection data on the data plate (voltage and frequency) match
the mains electricity supply. This data must correspond in order to
avoid the risk of damage to the appliance. Consult a qualified
electrician if in any doubt.
 Do not connect the appliance to the mains electricity supply by a
multi-socket unit or an extension lead. These are a fire hazard and
do not guarantee the required safety of the appliance.
6
Warning and Safety instructions
 For safety reasons, this appliance may only be used after it has
been built in.
 The cooker hood must not be used in a non-stationary location
(e.g. on a ship).
 Tampering with electrical connections or components and
mechanical parts is highly dangerous to the user and can cause
operational faults.
Only open the housing as described in the instructions given in the
installation sheet and in the Cleaning and care section of this
booklet. Under no circumstances should any other parts of the
housing be opened.
 The manufacturer's warranty will be invalidated if the appliance is
not repaired by a Miele approved service technician.
 Miele can only guarantee the safety of the appliance when
genuine original Miele replacement parts are used. Faulty
components must only be replaced by Miele spare parts.
 If the electrical connection cable is faulty it must only be replaced
by a Miele authorised service technician to protect the user from
danger.
 During installation, maintenance and repair work, the appliance
must be disconnected from the mains electricity supply.
7
Warning and Safety instructions
Using at the same time as other heating appliances that depend on the air
from the room
 Warning - danger of toxic fumes
Great care should be taken when using the cooker hood at the
same time and in the same room or area of the house as another
heating appliance which depends on the air in the room.
Such appliances include gas, oil, wood or coal-fired boilers and
heaters, continuous flow or other water heaters, gas hobs,
cookers or ovens which draw air in from the room and duct
exhaust gases out through a chimney or extraction ducting.
When used in extraction mode, with or without an external motor
fitted, or in recirculation mode with a recirculation box installed
outside the room, the appliance draws air in from the room in
which it is installed and from neighbouring rooms.
If there is insufficient air, an underpressure will occur. The heating
appliance will be starved of oxygen, impairing combustion.
Harmful gases could be drawn out of the chimney or extraction
ducting back into the room, with potentially fatal consequences.
8
Warning and Safety instructions
In order to ensure safe operation, and to prevent gases given off
by the heating appliances from being drawn back into the room
when the cooker hood and the heater are in operation
simultaneously, an underpressure in the room of 0.04 mbar (4 pa)
is the maximum permissible.
Ventilation can be maintained by air inlets which cannot be
blocked, in windows, doors or outside wall vents, or by other
technical measures, such as ensuring that the cooker hood can
only be switched on when the heating appliance is switched off or
vice versa. A ventilation brick alone is not generally sufficient to
ensure safe ventilation.
The overall ventilation condition of the dwelling must be taken into
account. If in any doubt, the advice of a competent builder or, for
gas a qualified gas fitter (registered with an official gas safety
body in accordance with national safety regulations, GasSafe in
the UK) must be sought.
If the cooker hood is used in recirculation mode, where the air is
directed back into the room in which it is located, operating a
heating appliance which depends on the room air at the same
time is no cause for concern.
9
Warning and Safety instructions
Correct use
 Never use a naked flame beneath the cooker hood. To avoid the
danger of fire, do not flambé or grill over a naked flame.
When switched on, the cooker hood could draw flames into the filter.
Fat deposits could ignite, presenting a fire hazard.
 The cooker hood can become damaged when exposed to
excessive heat.
– When using the cooker hood over a gas hob, ensure that any
burners in use are always covered by a pan. Switch the cooking
zone off when a pan is removed, even for a short time.
– Select a pan which is suitable for the size of the burner.
– Regulate the flame so that it does not burn up the sides of the
pan.
– Avoid overheating the pan (e.g. when cooking with a wok).
 Always switch the cooker hood on when a cooking zone is in use,
otherwise condensation may collect in the hood, which could cause
corrosion.
 When cooking with oil or fat, chip pans and deep fat fryers etc, do
not leave the pans unattended. Never leave an open grill unattended
when grilling. Overheated oil and fat can ignite and could set the
cooker hood on fire.
10
Warning and Safety instructions
 Do not use the cooker hood without the filters in place. This way
you will avoid the risk of grease and dirt getting into the appliance
and hindering its smooth operation.
 There is a risk of fire if the cooker hood is not cleaned as
described in these operating instructions.
 The cooker hood can get very hot during cooking due to heat
rising from the hob.
Do not touch the housing or the grease filters until the cooker hood
has cooled down.
Correct installation
 Refer to the cooker or hob manufacturer's instructions as to
whether a cooker hood may be operated above the cooker/hob.
 Safety regulations prohibit the fitting of a cooker hood over solid
fuel stoves.
 Insufficient distance between the cooker or hob and the cooker
hood can result in damage to the hood.
The minimum safety distances between the top of the cooker or hob
and the bottom of the cooker hood given in the "Installation" section
must be maintained, unless the hob manufacturer states that a
greater distance is required.
If more than one cooking appliance is fitted beneath the cooker
hood, and they have different minimum safety distances to the
cooker hood, select the greater distance.
 The distances given in "Installation" must be observed when
fitting the cooker hood.
 Exhaust ducting must be of non-inflammable material. Suitable
material is available from Miele specialist dealers or the Miele Spares
Dept.
 The appliance must not be connected to a chimney or flue which
is in use. Neither should it be connected to ducting which ventilates
rooms with fireplaces.
11
Warning and Safety instructions
 If exhaust air is to be extracted into a chimney or ventilation duct
no longer used for other purposes, seek professional advice.
Cleaning and care
 Do not use a steam cleaning appliance to clean this appliance.
The steam could reach electrical components and cause a short
circuit.
Accessories
 Only use genuine original Miele accessories with this appliance.
Using accessories from other manufacturers will invalidate the
guarantee, and Miele cannot accept liability.
12
Caring for the environment
Disposal of the packing
material
The packaging is designed to protect
the appliance from damage during
transportation. The packaging materials
used are selected from materials which
are environmentally friendly for disposal
and should be recycled.
Recycling the packaging reduces the
use of raw materials in the
manufacturing process and also
reduces the amount of waste in landfill
sites.
Disposal of your old appliance
Electrical and electronic appliances
often contain valuable materials. They
also contain materials which, if handled
or disposed of incorrectly, could be
potentially hazardous to human health
and to the environment. They are,
however, essential for the correct
functioning of your appliance. Please
do not therefore dispose of it with your
household waste.
Please dispose of it at your local
community waste collection / recycling
centre or contact your Dealer for
advice.
Ensure that it presents no danger to
children while being stored for disposal.
13
Guide to the appliance
14
Guide to the appliance
a Exhaust socket for air extraction/recirculation
b Controls
c Grease filter
d Pull-out deflector plate
e Hob lighting
f Charcoal filter
Accessory required for recirculation mode
g Sliding switch for the hob lighting
h Sliding switch for the fan
i Drop-down front panel
A front panel to match your kitchen furniture may be fitted instead of this panel
(DML 400 installation kit required).
15
Modes of operation
Depending on the model of the cooker
hood, the following options are
available:
Recirculation mode
(requires purchase of conversion kit and
charcoal filter: see "Technical Data")
Extraction mode
The air is drawn in and cleaned by the
grease filter and directed outside.
Non-return flap
The non-return flap is designed to
prevent the exchange of room and
outside air taking place.
The flap is closed when the cooker
hood is switched off.
When the cooker hood is switched on,
the non-return flap opens for the
cooking vapours to be blown directly
outside.
If the on-site ventilation system does
not have a non-return flap, the nonreturn flap supplied must be fitted in the
exhaust socket in the motor unit.
16
The air is drawn in and cleaned first by
the grease filter and then by a charcoal
filter. The cleaned air is then
recirculated back into the kitchen.
Operation
Switching the fan on
For light to heavy cooking vapours
select from power levels 1 to 3. For
short periods of strong vapours and
cooking odours, e.g. whilst searing
meat, select the IS (Intensive) setting.
 Pull the deflector plate out. For
optimum extraction with minimum
noise levels always pull the deflector
plate out to its full extent.
Switching the hob lighting
on/off
The hob lighting can be switched on
and off with the deflector pushed in or
pulled out and independently of the fan.
 Use the lighting switch  to switch
the hob lighting on (1) or off (0).
 Switch the fan on with the fan switch
 and select the power level you
want.
Fan run-on after cooking
 It is advisable to run the fan for a few
minutes after cooking has finished to
neutralise any lingering vapours and
odours in the air.
Switching the fan off
 Push the deflector plate in to switch
the fan off. The next time the
deflector plate is pulled out the
cooker hood will operate at the
power level it was at previously.
 Slide the fan switch to 0.
17
Energy saving tips
This cooker hood operates very
efficiently and economically. The
following will help you to save even
more energy when using it:
– Ensure that there is sufficient
ventilation in the kitchen when
cooking. In extraction mode, if there
is insufficient air flow the cooker
hood cannot operate efficiently and
this causes increased operating
noise levels.
– Always cook with the lowest possible
setting. This produces fewer cooking
vapours, so you can use a lower
cooker hood power level and
therefore benefit from reduced
energy consumption.
– Check the power level selected on
the cooker hood. A lower power level
is generally sufficient for the majority
of cooking. Only use the intensive
setting when necessary.
– When a large volume of cooking
vapours are being produced, switch
to a high power level in good time.
This is more efficient than operating
the cooker hood for longer to try to
capture cooking vapours which have
already been distributed throughout
the kitchen.
– Make sure that you switch the cooker
hood off after use.
– Clean or change the filters at regular
intervals. Heavily soiled filters reduce
performance, increase the risk of fire
and are unhygienic.
18
Cleaning and care
Casing
General information
The surfaces and controls are
susceptible to scratches and
abrasion.
Please observe the following
cleaning instructions.
 All external surfaces and controls can
be cleaned using hot water with a
small amount of washing-up liquid
applied with a well wrung-out soft
sponge or cloth.
Do not let moisture get into the
cooker hood.
Only use a damp cloth when
cleaning. This is particularly
important around the controls.
 After cleaning, wipe the surfaces dry
using a soft cloth.
Do not use:
– cleaning agents containing soda,
acids, chlorides or solvents,
– abrasive cleaning agents, e.g.
powder cleaners or cream cleaners
and abrasive sponges, as well as pot
scourers or sponges which have
been used previously with abrasive
cleaning agents. These will damage
the surface material.
Important for appliances with
stainless steel surfaces
(This information does not apply to the
controls).
 Stainless steel surfaces can be
cleaned with a proprietary nonabrasive cleaning agent designed
specifically for use on stainless steel.
 To help prevent re-soiling, a
proprietary conditioning agent for
stainless steel (available from Miele)
can also be used. Follow the
manufacturer’s instructions on the
packaging.
Important for the controls
Do not leave soiling on the controls
for any length of time.
Otherwise they may suffer
discolouration or damage.
Remove soiling straight away.
 Please observe the general notes on
cleaning earlier in this section.
Do not use stainless steel cleaning
agents on the controls.
19
Cleaning and care
Grease filter
The re-usable metal grease filter in the
appliance removes solid particles from
the kitchen vapours (grease, dust, etc)
preventing soiling of the cooker hood.
 An oversaturated filter is a fire
hazard.
Cleaning interval
When removing the grease filter do
not tilt it downwards at an angle.
This can damage the retaining pins.
Grease which is left to accumulate over
time will harden and become difficult to
remove. The grease filter should
therefore be cleaned at least every 3 - 4
weeks.
Removing a grease filter
The grease filter can fall out when
you are handling it.
This can result in damage to the filter
and the hob below.
Make sure you hold the filter
securely at all times when handling
it.
 With the deflector plate pushed in,
grip the front of the deflector plate
and hold the grease filter securely.
Whilst holding the grease filter pull
the deflector plate out as shown.
 Then lower the grease filter
downwards to remove it.
 Switch off the fan.
Cleaning the grease filter by hand
 Clean the filter with a soft nylon brush
in a mild solution of hot water and a
small amount of washing-up liquid.
Do not use "neat" washing up liquid.
20
Cleaning and care
Unsuitable cleaning agents
Fitting the grease filter
Unsuitable cleaning agents can cause
damage to the surface of the filters if
used regularly.
Do not use:
– cleaning agents containing descaling
agents
– powder cleaners, cream cleaners
– aggressive multi-purpose cleaning
agents or spray cleaners for grease
– oven sprays
Cleaning the grease filter in a
dishwasher
 Place the filter as upright as possible
in the lower basket, or at an angle,
ensuring the spray arm is not
obstructed.
 Use a proprietary household
dishwasher detergent.
 Select a dishwasher programme with
a wash temperature between 50°C
and 65°C.
 When fitting the grease filter, make
sure that the red plastic guides are at
the front and facing upwards.
 Replace the grease filter in the front
of the deflector plate, press it
upwards and push it in together with
the deflector plate. It will slide onto
the retaining pins at the back. Finally,
push the grease filter back a little
more.
Depending on the cleaning agent
used, cleaning a filter in a dishwasher
can cause permanent discolouration
to internal surfaces. However, this will
not affect the functioning of the filter
in any way.
After cleaning
 After cleaning, leave the filter to dry
on an absorbent surface before
replacing it.
 When removing the filter for cleaning,
also clean off any residues of oil or
fat from the now accessible casing to
prevent the risk of these catching fire.
21
Cleaning and care
Charcoal filter
If the cooker hood is connected for
recirculation, a charcoal filter must be
inserted in addition to the grease filter.
This is designed to absorb cooking
odours.
It is fitted in the canopy above the
grease filter.
Replacement charcoal filters can be
obtained from your Miele retailer or via
the internet at www.miele-shop.com.
See back of manual for contact details,
and "Technical data" for type and
reference number.
Fitting/replacing the charcoal filter
 Before fitting or replacing the
charcoal filter, the grease filter must
first be taken out (see previous
section for instructions on how to do
this).
 Take the charcoal filter out of its
packaging.
 Fit the charcoal filter into the frame.
 Replace the grease filter.
22
When to change the charcoal filter
 Always replace the charcoal filter
when it no longer absorbs kitchen
odours effectively.
It should, however be replaced at
least every 6 months.
Disposing of the charcoal filter
 Used charcoal filters can be disposed
of with the normal household waste.
Cleaning and care
Changing a halogen lamp
The halogen lamps should be replaced
with the following:
Manufacturer................................ EGLO
Lamp type .................................... GU10
Specification ................................ 11427
Wattage ........................................... 3 W
These halogen lamps are available from
Miele or from specialist retailers.
 Pull out the deflector plate, and
remove the grease filter as described
earlier.
 Switch off the fan and the lighting.
Note that halogen lamps become
very hot when in use.
They can cause burns even after
being switched off for some time!
Allow the lamps to cool down for a
few minutes before changing them.
 Remove the charcoal filter if the
cooker hood is being used in
recirculation mode.
 Disconnect the cooker hood from the
mains electrical supply before
replacing the lamps (see "Warning
and Safety instructions").
 Push down the lighting unit slightly
via the opening in the safety panel.
 Turn the halogen lamp anti-clockwise
and pull it out.
 Screw the new halogen lamp into the
socket and push it upwards. Please
follow the manufacturer's safety
instructions.
 Replace the grease filter and, if being
used in recirculation mode, the
charcoal filter.
23
After Sales / Guarantee
In the event of a fault which you cannot
remedy yourself, please contact your
Miele dealer or the Miele Service
Department.
Contact details for Miele are given at
the back of this manual. N.B. A call-out
charge will be applied to service visits
where the problem could have been
resolved as described in these
instructions.
When contacting your dealer or Miele,
please quote the model and serial
number of your appliance.
These are shown on the data plate.
Position of the data plate
The data plate is visible after removing
the grease filter.
Guarantee: U.K.
In the U.K., the appliance is guaranteed
for 2 years from the date of purchase.
However, you must activate your cover
by calling 0330 160 6640 or registering
online at www.miele.co.uk.
Guarantee: Other countries
For information on the appliance
guarantee specific to your country
please contact Miele. See end of this
booklet for contact details.
24
Installation
Before installation
 Before installation, it is important
to read the information given on the
following pages as well as the
"Warning and Safety instructions" at
the beginning of this booklet.
25
Installation
Assembly parts
26
Installation
a 1 exhaust connection
for exhaust ducting  150 mm
b 1 reducing collar
for exhaust ducting  125 mm
c 1 non-return flap
for fitting into the exhaust
connection on the motor unit (not
needed for recirculation mode)
d 2 brackets
for securing the cooker hood into
the wall unit
e 1 spacer strip
for concealing the gap between the
rear of the appliance and the wall
f Conversion kit for recirculation
mode
(not supplied, but available as an
optional accessory - see "Technical
data"). The kit contains an exhaust
grille and flexible aluminium hose
with hose clips.
14 screws 4 x 15 mm
for securing the cooker hood into the
wall unit
8 screws M4 x 12 mm
for securing the cooker hood to the
brackets
4 of the screws can be used instead of
the plastic rivets to secure the spacer
strip.
4 plastic rivets
for securing the spacer strip
g DML 400 installation kit for fitting
a drop-down front panel
(not supplied but available as an
optional accessory). Contains
hinging and screws for fitting a front
panel to match kitchen furniture.
27
Installation
Appliance dimensions
a The front section of the wall housing unit must be fitted with a shelf to the
depth of the partition wall. If the appliance is fitted further back, e.g. to
accommodate a front panel, then the shelf depth should be correspondingly
deeper.
b The partition wall in the wall unit must be removable.
c For extraction mode: the height of the wall unit and the cut-out dimensions
must take account of any accessories fitted, e.g. a silencer.
d Recirculation mode with conversion kit DUU 151.
e When installing the cooker hood with a DAR 3000 drop-down frame, make sure
that you note the different wall unit height (please refer to the dimensions given
in the DAR 3000 building-in diagram).
28
Installation
Safety distance between hob and cooker hood (S)
When planning the installation height of your cooker hood, the minimum safety
distance between the top of a cooker or hob and the bottom of the cooker
hood is as follows, unless a greater distance is specified by the manufacturer of
your cooking appliance.
See "Warning and Safety" instructions for further information.
Cooking appliance
Minimum distance S
Electric hob
450 mm
Electric grill, deep fat fryer (electric)
650 mm
Multi-burner gas hob,
total output ≤ 12.6 kW, no burner > 4.5 kW
650 mm
Multi-burner gas hob,
total output > 12.6 kW and ≤ 21.6 kW,
no burner > 4.8 kW.
760 mm
Multi-burner gas hob,
total output > 21.6 kW,
or multi-burner gas hob where one burner > 4.8 kW.
Single burner gas hob, output ≤ 6 kW.
Single burner gas hob, output > 6 kW and ≤ 8.1 kW.
Single burner gas hob, output > 8.1 kW
Not possible
650 mm
760 mm
Not possible
If you are fitting a front panel made of wood or plastic to the cooker hood,
observe the safety distances given by the hob manufacturer regarding the use
of easily flammable materials.
29
Installation
Installation recommendations
– To achieve optimum vapour
extraction, the cooker hood must
cover the hob. It should be
positioned centrally over the hob, not
to the side of it.
– The hob should be no wider than the
cooker hood, and if possible, it
should be narrower.
– The installation area must be easily
accessible. The cooker hood should
be easily accessible and easy to
dismantle in the event that service is
required. This should be taken into
consideration when planning the
position of cupboards, shelves,
ceilings or features in the vicinity of
the cooker hood.
30
Installation
a Example: Installation without a front
panel fitted and with the front edge
of the deflector plate flush with the
front edge of the furniture housing
unit. This installation needs a shelf
of at least 95 mm deep.
b Example: Installation with a front
panel to match the kitchen furniture.
This installation requires dimension
b for the front panel plus 5 mm for
the DML 400 fixing bracket to be
added to the shelf dimension.
The shelf must be correspondingly
deeper.
The remaining installation gap must be
at least 180 mm in depth. If it is less
than 180 mm, position the appliance
further back, and reduce measurement
T accordingly.
The position of the deflector plate can
be adjusted in depth by a maximum of
35 mm at the front.
To position the cooker hood correctly,
cut the spacer strip to the required
depth T and then attach it to the back
of the appliance:
T= Depth of carcase K minus depth of
appliance G
 Cut the spacer strip supplied to
measurement T. Score along the
groove for the smaller measurement
as shown, and remove the surplus.
31
Installation
 Secure the spacer strip underneath
the housing unit sides, flush with the
rear wall.
 Draw a vertical line up both inside
walls of the housing from the front of
the spacer strip.
32
 The brackets are designed for 16 and
19 mm thick unit sides. Orientate the
bracket so that the vertical depth
matches the thickness of the unit
side.
Screw the brackets onto the right and
left inside walls of the housing unit as
shown. The back edge of the bracket
should align with the vertical line
drawn up from the front of the spacer
strip and the lower edge should align
with the lower edge of the housing
unit side wall.
Installation
To avoid scratching the deflector
late, do not remove the protective
film between the deflector plate and
the casing until the hood has been
placed in the housing unit.
 Installation of the cooker hood is
carried out without the grease filter
placed in position. If the grease filter
has already been fitted, then it should
be removed (see "Cleaning and
care").
 Lift the appliance up into the housing
from below until the spring mounts at
the side engage in the brackets.
 Push the cooker hood back against
the spacer strip.
 Note for dismantling the cooker
hood: Undoing the screws on the left
and right inside the housing releases
the spring mounts allowing the
appliance to be removed from the
unit.
33
Installation
 Secure the cooker hood to the
brackets from below using two
screws on each side.
 Pull out the deflector plate and
remove the protective film between
the deflector plate and the casing.
 Secure the cooker hood to the floor
of the housing unit from below using
4 screws (6 screws are required for a
90 cm wide cooker hood).
To avoid damaging the deflector
plate when it is pulled out, care
should be taken to screw the fixing
screws in straight and to ensure that
the screwheads are countersunk.
34
 Secure the spacer strip to the back of
the appliance from behind using 4
plastic rivets as shown.
Installation
Attaching the front panel
Aligning the deflector plate
The front of the deflector plate can be
fitted with a front panel to match
existing kitchen furniture units.
The front panel must not exceed
1300 g. This applies to front panels with
a depth of up to 30 mm. For larger and
heavier front panels, the weight must
be reduced by e.g. machining it away at
the back.
The position of the deflector plate can
be brought forward by up to 35 mm
using the adjusting screws on either
side of the deflector plate. This allows
the deflector plate to be aligned to the
front of the kitchen furniture units on
either side.
A DML 400 installation kit, available as
an optional accessory, is required for
this.
 Follow the installation instructions
supplied.
 Use a screwdriver to align the
deflector plate correctly.
35
Installation
Fitting the grease filter
 Remove the protective foil around the
edge of the grease filter.
 When fitting the grease filter, make
sure that the red plastic guides are at
the front and facing upwards.
 Replace the grease filter in the front
of the deflector plate, press it
upwards and push it in together with
the deflector plate. It will slide onto
the retaining pins at the back. Finally,
push the grease filter back a little
more.
36
Exhaust socket
 Insert the non-return flap, if required.
Make sure that it opens easily and
closes again by itself.
 Attach the exhaust ducting, e.g.
flexible hose, to the exhaust socket
using a hose clip (available as an
optional accessory). When using
 125 mm ducting, fit the reducing
collar supplied into the exhaust
socket (see "Connection for air
extraction").
dai2699
Installation
Setting up for recirculation
mode
 Attach the exhaust ducting to the
exhaust socket on the cooker hood.
 See "Connection for air extraction"
for further instructions on fitting the
ducting.
If site conditions are not suitable for the
cooker hood to be used with air
extraction, the appliance must be set
up for recirculation. Conversion kit DUU
151, available through your dealer of
from Miele, is required for operating the
cooker hood in recirculation mode. You
will also need a charcoal filter (see
"Technical data").
 Fit the conversion kit as described in
the installation instructions supplied
with the kit. Make sure that the slats
in the exhaust grille point towards the
centre of the room and not towards a
37
Installation
wall or the ceiling.
A non-return flap is not used in
recirculation mode.
 Fit the charcoal filter (see "Cleaning
and care").
Electrical connection
Refer to the notes in “Electrical
connection” and “Warning and
Safety instructions” before
connecting to the electricity supply.
 Connect the cooker hood to the
electricity supply.
38
Electrical connection
All electrical work should be
undertaken by a suitably qualified
and competent person in strict
accordance with current national and
local safety regulations (BS 7671 in
the UK).
Installation, repairs and other work
by unqualified persons could be
dangerous, for which the
manufacturer cannot be held liable.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
The connection data is given on the
data plate. This is visible when the
grease filters have been removed.
Ensure that this data matches the
household mains supply.
If the switch is not accessible after
installation (depending on country), an
additional means of disconnection must
be provided for all poles.
For extra safety it is advisable to protect
the appliance with a suitable residual
current device (RCD). Contact a
qualified electrician for advice.
Important
This appliance is supplied for
connection to an a.c. 230 V single
phase 50 Hz supply. The wires in the
mains lead are coloured in accordance
with the following code:
Green/yellow ..................................earth
Blue..............................................neutral
Brown ................................................live
WARNING:
THIS APPLIANCE MUST BE
EARTHED
Connection of this appliance should be
made via a suitable isolator or a double
pole fused spur connection unit which
complies with national and local safety
regulations and the On-Off switch
should be easily accessible after the
appliance has been built in. When
switched off there must be an all-pole
contact gap of 3 mm in the switch
(including switch, fuses and relays
according to EN 60335).
39
Connection for air extraction
 If this cooker hood is used at the
same time as a heating appliance
that relies on oxygen from the same
room there is a risk in certain
circumstances of toxic fumes
building up.
It is essential that the "Warning and
Safety" instructions are observed.
The cooker hood should be installed
according to local and national
building regulations. Seek approval
from the building inspector where
necessary.
 Use smooth or flexible ducting made
from approved non-flammable
materials for exhaust ducting.
 To achieve the most efficient air
extraction with the lowest noise
levels, please note the following:
– To ensure efficient air extraction, the
diameter of the exhaust ducting
should not be less than 150 mm.
– If flat ducting is being used, the cross
section must not be smaller than the
cross sectional area of the exhaust
connection.
– The exhaust ducting should be as
short and straight as possible.
– Only use wide radius bends.
– The exhaust ducting must not be
kinked or compressed.
– Ensure that all connections are
strong and airtight.
Remember that any constriction of
the air flow will reduce extraction
performance and increase operating
noise.
40
 If the exhaust is ducted through an
outside wall, a telescopic wall vent or
a roof vent (available as an optional
accessory) is recommended.
 If the exhaust air is to be ducted into
a flue, the ducting must be directed
in the flow direction of the flue.
 When ducting is horizontal it must be
laid to slope away at at least 1 cm
per metre. This is to ensure that
condensate cannot drain back into
the appliance.
 If the exhaust ducting is to run
through rooms, ceiling space etc.
where there may be great variations
in temperature between the different
areas, the problem of condensation
will need to be addressed. The
exhaust ducting will need to be
suitably insulated.
Connection for air extraction
Condensate trap
In addition to insulating the exhaust
ducting, we recommend that a suitable
condensate trap is also installed to
collect and evaporate any condensate
which may occur.
Condensate traps for 125 mm or 150
mm ducting are available as optional
accessories.
 When installing a condensate trap,
ensure that it is positioned vertically
and as closely as possible above the
exhaust socket.
The arrow on the housing indicates
the direction of air-flow.
Silencer
To achieve even further reductions in
noise levels, a special silencer (optional
accessory) can be fitted in the ducting
system.
Extraction mode
The silencer not only reduces noise
from the motor outside the house, but
also sounds from outside (e.g. traffic
noise). For this reason the silencer must
be positioned as close as possible to
the ducting exit .
41
Connection for air extraction
Recirculation mode
The silencer needs to be positioned
between the exhaust socket and the
exhaust grille . Ensure there is
adequate space for fitting it.
42
Technical data
Fan motor
Hob lighting
Total connected load
Voltage, frequency
Fuse rating
110 W
2x3W
116 W
AC 230 V, 50 Hz
5A
Mains connection cable length
1.5 m
Weight
12 kg
Special accessories for recirculation mode:
Conversion kit DUU 151 and charcoal filter DKF 13-1.
43
Technical data
Data sheet for domestic cooker hoods
In acc. with delegated regulation (EU) No. 65/2014 and regulation (EU) No.
66/2014
MIELE
Model name / identifier
DA 3366
Annual Energy Consumption (AEChood)
61,4 kWh/year
Energy efficiency class
A+ (most efficient) to F (least efficient)
C
Energy efficiency index (EEIhood)
80,5
Fluid Dynamic Efficiency (FDEhood)
14,2
Fluid Dynamic Efficiency class
A (most efficient) to G (least efficient)
D
Lighting Efficiency (LEhood)
53,3 lx/W
Lighting Efficiency class
A (most efficient) to G (least efficient)
A
Grease Filtering Efficiency
89,0 %
Grease Filtering Efficiency class
A (most efficient) to G (least efficient)
B
Airflow at best efficiency point
246,8 m3/h
Air flow (min. speed)
150 m3/h
Air flow (max. speed)
320 m3/h
Air flow (intensive or boost setting)
430 m3/h
Max. air flow (Qmax)
430 m3/h
Air pressure at best efficiency point
217 Pa
Airborne acoustical A-weighted sound power emissions (min. speed)
44 dB
Airborne acoustical A-weighted sound power emissions (max. speed)
51 dB
Airborne acoustical A-weighted sound power emissions (intensive or
boost setting)
58 dB
Electrical power input at best efficiency point
105,0 W
Power consumption in off mode (Po)
0,00 W
Power consumption in standby mode (Ps)
W
Nominal power of lighting system
6,0 W
Average illumination of the lighting system on the cooking surface
320 Ix
Time increase factor
1,5
44
United Kingdom
Miele Co. Ltd.
Fairacres, Marcham Road
Abingdon, Oxon, OX14 1TW
Customer Contact Centre Tel: 0330 160 6600
E-mail: mielecare@miele.co.uk
Internet: www.miele.co.uk
Australia
Miele Australia Pty. Ltd.
ACN 005 635 398
ABN 96 005 635 398
1 Gilbert Park Drive, Knoxfield, VIC 3180
Tel: 1300 464 353
Internet: www.miele.com.au
China
Miele (Shanghai) Trading Ltd.
1-3 Floor, No. 82 Shi Men Yi Road
Jing' an District
200040 Shanghai, PRC
Tel: +86 21 6157 3500, Fax: +86 21 6157 3511
E-mail: info@miele.cn, Internet: www.miele.cn
Miele (Hong Kong) Limited
41/F - 4101, Manhattan Place
23 Wang Tai Road
Kowloon Bay, Hong Kong
Tel: (852) 2610 1331, Fax: (852)2610 1013
Email: mielehk@miele.com.hk
India
Miele India Pvt. Ltd.
Ground Floor, Copia Corporate Suites
Plot No. 9, Jasola
New Delhi - 110025
Tel: 011-46 900 000, Fax: 011-46 900 001
E-mail: customercare@miele.in, Internet: www.miele.in
Ireland
Miele Ireland Ltd.
2024 Bianconi Avenue
Citywest Business Campus, Dublin 24
Tel: (01) 461 07 10, Fax: (01) 461 07 97
E-Mail: info@miele.ie, Internet: www.miele.ie
Manufacturer: Miele & Cie. KG
Carl-Miele-Straße 29, 33332 Gütersloh, Germany
45
Malaysia
Miele Sdn Bhd
Suite 12-2, Level 12
Menara Sapura Kencana Petroleum
Solaris Dutamas No. 1, Jalan Dutamas 1
50480 Kuala Lumpur, Malaysia
Phone: +603-6209-0288
Fax: +603-6205-3768
New Zealand
Miele New Zealand Limited
IRD 98 463 631
Level 2, 10 College Hill
Freemans Bay, Auckland 1011, NZ
Tel: 0800 464 353
Internet: www.miele.co.nz
Singapore
Miele Pte. Ltd.
163 Penang Road
# 04 - 03 Winsland House II
Singapore 238463
Tel: +65 6735 1191, Fax: +65 6735 1161
E-Mail: info@miele.com.sg
Internet: www.miele.sg
South Africa
Miele (Pty) Ltd
63 Peter Place, Bryanston 2194
P.O. Box 69434, Bryanston 2021
Tel: (011) 875 9000, Fax: (011) 875 9035
E-mail: info@miele.co.za
Internet: www.miele.co.za
United Arab Emirates
Miele Appliances Ltd.
P.O. Box 11 47 82
Gold & Diamond Park, Sheikh Zayed Road
Building 6 / Offices Nos. 6-214 to 6-220
Dubai
Tel: +971-4-341 84 44
Fax: +971-4-341 88 52
E-Mail: info@miele.ae
Internet: www.miele.ae
DA 3366

en-GB
M.-Nr. 10 093 460 / 01
Download PDF

advertising