AL-1660-EDPB
RS-360-EDPB
Deluxe Alarm & Remote Start w/ BLADE Technology
July 8, 2014
Operation Guide
Temporary cover. Color cover is in a separate file.
1
Table Of Contents
Transmitter Overview��������������������������������������������������������������������������������������������������� 3
Transmitter Functions��������������������������������������������������������������������������������������������������� 3
Low Battery/Low Temp Automatic Starting��������������������������������������������������������������� 6
Other Remote Start Features��������������������������������������������������������������������������������������� 6
Turbo Timer Feature������������������������������������������������������������������������������������������������� 7
Pit-Stop Feature������������������������������������������������������������������������������������������������������� 7
Manual Transmission Starting���������������������������������������������������������������������������������� 7
Security System Features�������������������������������������������������������������������������������������������� 7
Last Door Arming������������������������������������������������������������������������������������������������������ 7
Automatic Rearming������������������������������������������������������������������������������������������������� 7
Pre-Warn Detection�������������������������������������������������������������������������������������������������� 8
When The System Triggers�������������������������������������������������������������������������������������� 8
Using The Valet Switch������������������������������������������������������������������������������������������������� 8
Emergency Override������������������������������������������������������������������������������������������������ 8
Valet Mode���������������������������������������������������������������������������������������������������������������� 8
SecureCode������������������������������������������������������������������������������������������������������������� 9
The Status Light����������������������������������������������������������������������������������������������������������� 9
Anti-Carjacking Protection������������������������������������������������������������������������������������������ 10
Programming Transmitters������������������������������������������������������������������������������������������11
Programming Features������������������������������������������������������������������������������������������������11
User Programmable Features������������������������������������������������������������������������������������ 12
Installer Programmable Features������������������������������������������������������������������������������� 15
Programmable Features Matrix���������������������������������������������������������������������������������� 19
This device complies with FCC Rules part 15. Operation is subject to the following
two conditions, (1) This device may not cause harmful interference and, (2) This
device must accept any interference that may be received, including interference
that may cause undesired operation.
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the
user’s authority to operate the equipment.
2
Transmitter Overview
Transmitter part number:
1411-03
Call your dealer or visit
www.caralarm.com to order
replacement transmitters.
“lock”
button
Battery replacement:
Remove the small screw from the
lower back case, and separate the
transmitter halves� Replace the
CR2032 battery (or with 2 CR2016
batteries) and reassemble the
transmitter case�
“unlock”
button
“start”
button
“trunk”
button
This system is EChO compatible, which means you can upgrade at anytime to
have 2-way capability and greater range (up to 1-mile!). it’s a simple upgrade
that only takes minutes, so talk to your dealer about upgrading with EChO
TEChnOLOGy today!!
Transmitter Functions
LOCK / ARm: Press and release the “LOCK” button�
• THE SIREN / HORN WILL CHIRP & THE PARKING
LIGHTS WILL FLASH ONCE�
unLOCK / DiSARm: Press and release the “UNLOCK” button�
• THE SIREN / HORN WILL CHIRP TWICE & THE PARKING LIGHTS WILL FLASH TWICE, THEN ILLUMINATE FOR
30 SECONDS�
3
Transmitter Functions (cont’d)
TRunK RELEASE / ChAnnEL 2: Press the “TRUNK” button for 3
seconds�
• THE SYSTEM WILL DISARM / UNLOCK AND THE
TRUNK WILL OPEN (IF EQUIPPED)�
REmOTE START: Press and release the “START” button twice
within 5 seconds� (see user feature #8 for additional options)
x2
• THE PARKING LIGHTS WILL FLASH ONCE AND THE
STATUS LIGHT WILL FLASH RAPIDLY�
• THE SYSTEM WILL TURN ON THE IGNITIONS AND
PROCEED TO START THE ENGINE�
• ONCE THE ENGINE IS RUNNING, THE PARKING
LIGHTS WILL TURN ON AND STAY ON AND THE STATUS
LIGHTS WILL FLASH SLOWLY�
• If the engine stalls, the system will make up to 3 more attempts�
• Each time you park, set the climate controls as desired when you use the remote start� The
engine will run for the preset run time (see user feature #1)�
• Run Time Extender: Press the “START” button one time during remote start to restart the
engine run timer�
nOTE: This can only be used once per remote start cycle.
• If you decide not to drive your vehicle, you can turn off the remote start using the same method
to turn it on (Default = press “START” twice in 5 seconds)
nOTE: if remote start activation is programmed for 1 press, the 1st press activates Run
Time Extender so an additional press is required to turn off remote start.
• Upon entering the vehicle during remote start mode, turn the ignition key to the “ON/RUN” position (nOT START!!)� When you press the brake pedal, the remote start will turn off allowing the
ignition key to take over�
ChAnnEL 3: Press and hold the “TRUNK” & “START“ buttons for 3
seconds�
• YOUR SYSTEM WILL ACTIVATE THE CHANNEL 3
OUTPUT�
4
Transmitter Functions (cont’d)
ChAnnEL 4: Press and hold the “LOCK” & “TRUNK” buttons for 3
seconds�
• YOUR SYSTEM WILL ACTIVATE THE CHANNEL 4
OUTPUT�
ChAnnEL 5: Press and hold the “UNLOCK” & “START“ buttons for
3 seconds�
• YOUR SYSTEM WILL ACTIVATE THE CHANNEL 5
OUTPUT�
PAniC: Press and hold the “LOCK” or “UNLOCK” button for 3
seconds�
• THE SIREN / HORN WILL SOUND, THE PARKING LIGHTS WILL FLASH, AND THE DOORS WILL
LOCK OR UNLOCK DEPENDING WHICH BUTTON IS
PRESSED�
OR
SiLEnT LOCK / unLOCK: Press and release the “TRUNK” button
twice in 5 seconds�
• THE PARKING LIGHTS WILL FLASH, AND THE
SYSTEM WILL LOCK/ARM OR UNLOCK/DISARM
DEPENDING ON THE CURRENT SYSTEM STATE�
x2
REmOTE VALET: Press “LOCK” then “UNLOCK” then “TRUNK” +
“START” within 5 seconds�
1
2
3
• THE SYSTEM WILL ENTER ALARM VALET MODE�
SEE PAGE 8 FOR MORE INFO ON VALET MODES�
5
Transmitter Functions (cont’d)
SEnSOR ByPASS: Press and release the “TRUNK” button within 5
seconds of locking/arming the alarm system�
1
• THE SYSTEM WILL GIVE ONE CHIRP TO INDICATE
THE SENSOR IS BYPASSED�
NOTE: ALARM FUNCTIONS MUST BE ENABLED FOR
THIS OPERATION
2
LOW VOLTAGE/TEmP AuTO START: Press and release the
“START” button within 5 seconds of locking/arming the system�
1
2
• THE SYSTEM WILL GIVE ONE CHIRP TO INDICATE
THE LOW VOLT/LOW TEMP (15 DEGREES ONLY)
AUTOSTART IS ACTIVATED�
SEE BELOW FOR MORE INFO.
AuXiLiARy FunCTiOnS 1-4:
The actual operation of these functions will vary from car to car� They are designed to operate
extra functions like automatic sliding doors or motorized hatches� Aux 1-4 are virtual outputs only
available when this system is integrated with the vehicle’s data network� Consult with your installer
to find out if any of these functions are available, then confirm each operation and write them
below�
- Auxiliary 1 Function (___________________): To activate this function, press and release the
“trunk” and “start” buttons simultaneously)�
- Auxiliary 2 Function (___________________): To activate this function, press and release the
“lock” and “trunk” buttons simultaneously)�
- Auxiliary 3 Function (___________________): To activate this function, press and release the
“unlock” and “start” buttons simultaneously)�
- Auxiliary 4 Function (___________________): To activate this function, press and release the
“unlock” and “trunk” buttons simultaneously)�
Other Remote Start Features
LOW BATTERy/LOW TEmP AuTOmATiC STARTinG
This feature will automatically start the engine if the vehicle battery drops below 11 volts or the
interior temperature drops to 15 (or 32) degrees fahrenheit� You must activate these features each
time you park your car to use them� They can be activated one of two ways:
method 1 - Valet Switch
• Turn the ignition switch “on”, then “off” (engine not running), and within 7 seconds press the
valet switch twice� If there is a 2 second delay without additional valet button presses, the horn
will honk 3 times activating low voltage start mode�
• To activate low temp starting, enter low voltage start mode as described above but,
immeditately after the horn honks, press the valet switch 1 time (15 degrees) or 2 times
6 (32 degrees) within 5 seconds. The horn will honk to confirm your selection.
Other Remote Start Features (cont’d)
Method 2 - With The Controller (Low Volt + Low Temp - 15 Degrees Only)
• Within 5 seconds of pressing LOCK, press the START button. You will get one chirp to confirm.
NOTE: When low temp start mode is activated, low voltage start is also activated. These features
will operate once every two hours until the ignition key is turned “ON”.
Turbo Timer Feature
This is recommended for vehicles equipped with a turbocharger. It allows the engine to idle
after driving to cool the turbo. When this Installer Programmable Feature (#10) is enabled, the
system will automatically keep the engine running as follows:
• With the engine running, hold the brake pedal and engage the parking brake.
When the brake pedal is released, the system will keep the engine running for the programmed
time (1, 2, or 3 minutes), and then automatically turn it off. • The system may be locked while the engine is running. Turbo Timer can be prevented from
engaging, or “bypassed” if desired, by turning the engine off before engaging the parking brake.
Pit-Stop Feature
This feature allows you to leave your engine running for making quick errands. To use this feature, have the engine running normally from the ignition switch and your foot off the brake pedal.
Press the Valet Switch twice; the parking lights will flash and the horn chirps 5 times. Turn the key
off and the engine will remain running for the programmed run time.
Manual Transmission Starting
Remote starting with a manual transmission requires a different installation method and
installer feature #11 must be turned on. Also, a setup procedure that ensures the transmission
was left in neutral must be performed each time you leave your vehicle and intend to use remote
start later. Perform these steps:
1) With the car running, hold the brake pedal, apply the parking brake, release the brake pedal.
2) Use the transmitter as if you were activating remote start (default: press START twice). The
status light will start to flash slow.
3) Turn off the ignition key and exit the vehicle.
4) Press LOCK on the transmitter. The engine will shut down (unless turbo timer is on) and the
status light will flash every 2 seconds to indicate it is ready to be remote started.
NOTE: Manual transmission setup will cancel if you enter the vehicle.
Security System Features
NOTE: Security features are optional for the RS-360-EDPB. Talk to your dealer to learn
more about upgrading.
Last Door Arming
This system can be configured to arm automatically when all the vehicle’s doors are closed
(see user feature #9). When enabled, the siren/horn will chirp once when all of the doors are
closed. It will start a 30 second countdown (indicated by a fast flashing status light) after which,
the system will lock and/or arm. The 30 second arming delay will paused while a point of entry is
open. Turning ON the ignition key will cancel the arming sequence until the key is turned off and
the doors are all closed once again.
NOTE: Installer feature #13 must be on and the system must be wired for security functions
Automatic Rearming
This automatically rearms the alarm if the system is disarmed from the remote. (see user
feature #10). When disarmed by remote, the system will start a 90 second countdown (fast
flashing status light) to arm the system. This is useful if the controller accidentally disarms the
system when it’s kept in a purse or pocket where other items could potentially press the buttons.
ENHANCED AUTO REARM allows you to cancel the countdown by pressing UNLOCK a second
time within 5 seconds of the first press to disarm the alarm.
NOTE: Installer feature #13 must be on and the system must be wired for
7
security functions
Security System Features (cont’d)
Pre-Warn Detection
This system’s impact sensor (optional for the RS-360-EDPB) is designed, in addition to detecting a full impact, to warn away potential violators when it detects a light
impact to the vehicle. The system will respond by chirping the siren/horn 3 times and
locking the doors. This is very useful when an intruder attempts to unlock the door.
When The System Triggers
If the system were to be compromised while armed, it will trigger sounding the
siren/horn and flashing the parking lights for 30 seconds (programmable). When
disarming the system after a trigger event, the siren/horn will chirp 4 times and the
parking lights will flash 4 times instead of the standard 2 times.
LOCK ON TRIGGER: If a door is opened when the system is triggered, it will wait
until the door is closed again, then lock the doors. This patented feature is useful to
further deny a thief of further access to the vehicle.
STORM SAFE MODE: When the system is triggered, pressing the “UNLOCK” button
will stop the alarm from sounding but will leave the doors locked. This function is useful if you have a false triggering situation due to violent weather.
ZONE VIOLATION RECALL: The system is capable of telling you which zones were
triggered last. The system’s status light will flash to indicate which zone was triggered.
This occurs during the alarm cycle AND after disarming. The system will store the last
triggered zone until the vehicle’s ignition key is turned on. See “The Status Light” section oon page 9 for further explanation of this feature.
NUISANCE PREVENTION: If the system prewarns 5 times within 15 minutes, it will
bypass the zone for the remainder of the 15 minutes before rearming the pre-warn
zone. Additionally, if a full trigger zone is left open, the system will trigger a total of 3
times before bypassing the zone. Once the zone is closed, it will re-arm that zone.
Using The Valet Switch
Emergency Override
If you lose or break your controller, you’ll need to perform an emergency override to
disarm the system and use your vehicle. To do so, use the following steps:
STEP 1 - Enter the vehicle (the alarm should sound)
STEP 2 - Turn the ignition key to the “ON” position
STEP 3 - Press the valet switch (located in the window-mount antenna) once
NOTE: Enter your SecureCode at this time if programmed (user feature #13)
STEP 4 - Turn the ignition “OFF”.
Valet Mode
Valet mode completely disables all security & remote start functions. Keyless entry
is still operable. To enter valet mode, perform the following steps:
STEP 1 - Disarm the system by remote or by performing an emergency override.
STEP 2 - Press and hold the valet switch for 2 seconds. The system will chirp once
and the status light will turn on.
EXITING VALET MODE - Press and release the valet switch once. The status light
will turn off.
8
Using The Valet Switch (cont’d)
SecureCode
SecureCode allows you to customize the number of valet presses required to
perform an emergency override. SecureCode has 2 stages with the first requiring 1-9
button valet presses and the second requiring 0-9 valet button presses. This gives
you 99 possible combinations. To program a custom SecureCode, please refer to
user feature #13.
To perform an emergency override with SecureCode, use the following steps:
STEP 1 - With the system armed, enter the vehicle (the alarm will activate).
STEP 2 - Turn the ignition switch to the “ON” position.
STEP 3 - Within 5 seconds of step 2, press the valet switch to enter the first digit of
your programmed code.
STEP 4 - After a few seconds, the siren will stop sounding and chirp once (confirming
stage 1). The siren will then continue sounding.
STEP 5 - Now, within 5 seconds of step 4, press the valet switch to enter the second
digit of your code. If the code is correct, the alarm will disarm.
If the code is entered incorrectly, turn the ignition key OFF, then back ON to try
again. If 2 failed attempts are made, no further attempts can be made for 2 minutes.
The Status Light
The status lights, located in the window-mount antenna, provide a visual indication
of the system’s status.
SECURITY SYSTEM STATUS
OFF: The alarm is disarmed and not performing any automatic functions.
ON: The alarm is in valet mode.
FLASHING SLOW: The alarm is armed and monitoring all entry points.
FLASHING FAST: One of the automatic arming features is in progress.
AUTOMATIC TRANSMITTER VERIFICATION
Every time you turn on the ignition key, the status light will flash a number of times
equal to the number of transmitters programmed to the system. This unique security
feature combats potential thieves (valet attendant, mechanic, etc.) from adding their
own transmitter without your knowledge and accessing your vehicle at a later time.
ALARM ZONE VIOLATION RECALL
If the security system is triggered, upon disarming, the status lights will flash
a number of times to indicate exactly which zone(s), has been violated. It will
store the last 2 violated circuits and continually repeat the flash pattern until the
vehicle’s ignition key is turned ON.
2 FLASHES: Hood trigger
3 FLASHES: Door trigger
4 FLASHES: Sensor port trigger
REMOTE START STATUS
FLASHING SLOW: The engine was remote started successfully and is running.
FLASHING FAST: The remote start sequence has begun and is in process of starting
the vehicle’s engine.
2 FLASHES, PAUSE: The engine is running while the alarm is armed.
9
The Status Light (cont’d)
REMOTE START DIAGNOSTICS
The remote start system can also indicate which zone caused the last remote start
cycle to end. To see this indicator, place the system into alarm valet mode. Immediately after the chirp, the status light will flash to indicate which zone violation occured.
1 FLASH: Run time expired.
2 FLASHES: Brake pedal was pressed or the hood was opened.
3 FLASHES: Engine stalled or a bad tach signal.
4 FLASHES: Received transmitter command to stop.
5 FLASHES: The neutral safety circuit was triggered.
6 FLASHES: The alarm was triggered or low battery voltage.
Anti-Carjacking Protection
The system is equipped with two separate Anti-Carjacking protection features
(ignition, open door, or both) that are selectable via user feature #12. Once activated,
the user has 60 seconds to cancel the Anti-Carjacking protection process (described
below). If Anti-Carjacking is not cancelled, 53 seconds after being activated the siren
will begin to chirp for 7 seconds to alert the user that the system is about to enter into
an alarm condition. The Valet Switch may still be pressed once during this period to
cancel the Anti-Carjacking process.
If the Anti-Carjacking process is not cancelled before the 60 second countdown
expires, the system will enter an alarm condition, sounding the siren and flashing the
parking lights. 30 seconds after this occurs, or should the ignition be turned off in the
meantime, the stater interrupt will engage. Once the system enters the alarm condition, it will not respond to the transmitter, nor will the system reset automatically after
60 seconds, and it can only be disengaged by:
Step 1 Turning the vehicle’s ignition off.
Step 2 Turning the ignition back on.
Step 3 Within 5 seconds, perform an Emergency Override using the Valet Switch.
NOTE: SecureCode (see user feature #13) is required if it has been customized.
TYPES OF ANTI-CARJACKING PROTECTION
Ignition Activated Anti-Carjacking activates every time the vehicle’s ignition is
turned on. The Valet Switch must be pressed within 60 seconds of activating to
cancel Anti-Carjacking.
Door Anti-Carjacking activates when a door is opened after the vehicle is started
and the engine is running. The Valet Switch must be pressed within 60 seconds after
activation to cancel Anti-Carjacking.
10
Programming Transmitters
Standard Programming: This method to program additional or replacement transmitters does not affect the Unauthorized Transmitter Alert (UTA) feature. Before you
begin, have all transmitters which are to operate the system at hand.
Step 1Then, turn the ignition “on” (do not crank the engine).
Step 2Within 5 seconds of Step 1, press the Valet Switch 5 times. The siren/horn will
briefly sound, confirming that the system is ready to learn a transmitter code.
Step 3Press the “lock” button on each transmitter one at a time. The system will
chirp the siren/horn once to confirm that each was learned. If a code is not received
within 10 seconds of Step 2, the learning process will automatically exit.
Step 4Then, turn the ignition “off” or wait 10 seconds to exit programming mode.
If the Unauthorized Transmitter Alert feature is on, programming a transmitter to the
system will activate the “UTA” warning and the extended Status Light indication. For
the next 48 hours, the siren/horn will sound a brief series of chirps every time the
vehicle’s ignition key is turned on.
Special Programming procedure to turn on the UTA feature: Use this method to
program transmitters or optional controllers, and to turn on the Unauthorized Transmitter Alert feature.
Follow the same steps as the Standard Programming, but on any transmitter/controller being programmed instead of pressing the “lock” button, press the “lock” and
the “unlock” buttons together. This action turns on the Unauthorized Transmitter
Alert feature and at the same time programs the transmitter or controller to operate
the system.
Once the Unauthorized Transmitter Alert feature is turned on, the warning will
sound for 48 hours after any transmitter programming. This feature can only be
turned off again by sending the system back to Omega for a reset.
Programming Features
A matrix of all programmable features and their options are on the last page of this
guide. For detailed information on each feature, please refer to the next section. Use
the procedure below to make any necessary changes.
TO MANUALLY CHANGE FEATURES:
Step 1 Turn the ignition key “ON”, then “OFF” (do not crank the engine)
Step 2 Within 5 seconds of step 1, press the valet switch 5 times to access user
features (Press 10 times to access installer features).
~ The siren/horn will sound and the status light will turn on.
Step 3 Within 10 seconds of step 2, press the valet switch the number of times corresponding with the desired feature’s number.
~ The siren/horn will chirp equal to the selected feature.
Step 4 Change the feature by pressing the remote button that matches the desired
setting.
~ The siren/horn will chirp equal to the selected setting.
Step 5 If you wish to change more features, repeat steps 3 & 4 at this time.
Step 6 To exit programming, turn the ignition key “ON” then “OFF”. Or, it will exit
automatically after 10 seconds of no activity.
11
User Programmable Features
Feature #1 - Remote Start Run Time
10 Minutes (press “lock” button to program) - DEFAULT
5 Minutes (press “unlock” button to program)
15 Minutes (press “trunk” button to program)
20 Minutes (press “start” to program)
This sets the maximum amount of time that the remote start will keep the engine
running if it is not shut down by other methods.
Feature #2 - Flashing Light Confirmations
Unlock: ON, RS: ON (press “lock” button to program)
Unlock: ON, RS: Flash (press “unlock” button to program)
Unlock: Flash, RS: ON (press “trunk” button to program)
Unlock: Flash, RS: Flash (press “start” button to program) - DEFAULT
This feature affects the parking light confirmations for system unlock & remote start
functions. With the above options, you can select any combination of:
Unlock: Flash - Flashes twice after unlock
Unlock: ON - Flashes twice then stays on for 30 seconds after unlock
RS: ON - Stays on during remote start mode
RS: Flash - Flashes once every 1.5 seconds during remote start mode
Feature #3 - Confirmation Chirp Volume Low (softest) (press “lock” button to program)
Medium Low
(press “unlock” button to program)
Medium High
(press “trunk” button to program) - DEFAULT
High (loudest) (press “start” button to program)
This feature allows the choice different chirp volume levels, and when programming
it, each selection will be confirmed in the chosen volume making it easy to choose the
most suitable setting.
Feature #4 - BROWN Wire Audible Output
Pulsed Horn Low
(press “lock” button to program) - DEFAULT (RS-360-EDPB)
Pulsed Horn Medium (press “unlock” button to program)
Pulsed Horn High
(press “trunk” button to program)
Steady Siren(press “start” button to program) - DEFAULT (AL-1660-EDPB)
This changes the BROWN wire’s audible output when the alarm is triggered. Steady
siren must be selected when using a siren (other horn outputs stay at the Medium
setting). The horn honk options will affect all horn honk outputs used as well as
change the BROWN wire’s function.
Feature #5 - Ignition Controlled Lock/Unlock
Off(press “lock” button to program) - DEFAULT
Lock w/ Ignition On(press “unlock” button to program)
Unlock w/ Ignition Off (press “trunk” button to program)
Lock And Unlock w/ Ignition (press “start” button to program)
This feature controls the lock/unlock operations when the ignition key is turned on/off,
Feature #6 - Open Door Bypass of Ignition Locking
On
(press “lock” button to program) - DEFAULT
Off
(press “unlock” button to program)
This feature cancels the automatic locking or unlocking of the vehicle’s doors if one of
the doors is open when the ignition switch is turned on or off.
12
User Programmable Features (cont’d)
Feature #7 - Unlock w/ Trunk Release
On
(press “lock” button to program) - DEFAULT
Off
(press “unlock” button to program)
“2nd channel” is most commonly used for trunk release, in which case the alarm
should also disarm. This feature, when on, configures the system to unlock/disarm
when the 2nd channel is activated.
Feature #8 - Remote Start Activation From The Remote
Press “start” button 1 time (press “lock” button to program)
Press “start” button 2 times (press “unlock” button to program) - DEFAULT
Press “start” button 3 times (press “trunk” button to program)
Press “start” button 4 times (press start” button to program)
This feature changes how the remote start feature is activated from the remote.
Feature #9 - Last Door Arming
Off (press “lock” button to program) - DEFAULT
On w/o doors locking (press “unlock” button to program)
On w/ doors locking (press “trunk” button to program)
“Last Door Arming” has the system automatically arm itself every time you exit the
vehicle (the complete operation is described on page 7).
Feature #10 - Automatic Rearming
Off(press “lock” button to program) - DEFAULT
On w/o doors locking (press “unlock” button to program)
On w/ doors locking (press “trunk” button to program)
Enhanced auto rearm (press “start” button to program)
“Automatic Rearming”, described on page 7, rearms the alarm if accidentally disarmed. Options are to have Automatic Rearming operate with or without also locking
the doors when the system does rearm. Enhanced auto rearm allows you to cancel
the rearming sequence by pressing unlock a 2nd time after disarming.
Feature #11 - Confirmation Chirps
Siren + Horn(press “lock” button to program)
Siren Only(press “unlock” button to program) - DEFAULT
On Demand (siren+horn) (press “trunk” button to program)
Off(press “start” button to program)
This feature selects whether the siren and/or horn give confirmation chirps. Both
outputs will always sound when the alarm system is triggered or in panic mode.
Feature #12 - Anti-Carjacking
Ignition Only (press “lock” button to program)
Door Only (press “unlock” button to program)
Ignition + Door (press “trunk” button to program)
Off
(press “start” button to program) - DEFAULT
This selects between the 2 forms of anti-carjacking protection. Details on using anticarjacking protection are described on page 10.
13
User Programmable Features (cont’d)
Feature #13 - SecureCode
DEFAULT - 1 Press
SecureCode is a unique patented feature which allows you to custom select the
number of Valet Switch presses in two stages, instead of a single “1 press”, which
would be required in order to perform an Emergency Override. If any of the three anticarjacking features are utilized, a customized SecureCode would also be required to
turn it off once it is fully activated. SecureCode operation is described on page 9.
To custom program a new SecureCode:
Step 1Access user feature #13 (follow the steps on page 9).
Step 2Within 10 seconds slowly press and release the transmitter’s “arm/lock”
button the number of times equal to the desired SecureCode for stage 1, allow the
system to respond to each transmitter button press with a siren chirp before pressing
the button again. A few seconds after the final button press, the system will chirp the
horn/siren confirming the total number for stage 1.
Step 3Configure stage 2 of the SecureCode by pressing and releasing the “disarm/
unlock” button the number of times desired for the stage 2. The system will
confirm as it did for stage 1.
Feature #14 - Ignition Activated Override
On
(press “lock” button to program)
Off
(press “unlock” button to program) - DEFAULT
This feature allows an activated system to be overridden and disarmed by simply
turning the ignition switch on within 10 seconds of the system’s activation. After 10
seconds, the Emergency Override must be performed.
Feature #15 - Alarm Trigger Duration
30 Seconds (press “lock” button to program) - DEFAULT
60 Seconds (press “unlock” button to program)
90 Seconds (press “trunk” button to program)
120 Seconds (press “start” button to program)
This feature selects the period of time for which the system sounds the siren (and/or
horn) and flashes the lights when triggered. Caution: Before lengthening the Alarm
Duration you should always check and determine if there are any local antinoise or nuisance ordinances in your area.
Feature #16 - Arming Delay
3 Seconds
(press “lock” button to program) - DEFAULT
15 Seconds (press “unlock” button to program)
30 Seconds (press “trunk” button to program)
45 Seconds (press “start” button to program)
This selects how long the alarm waits to monitor trigger zones after arming.
Feature #17 - Open Door Warning Upon Arming
On
(press “lock” button to program)
Off
(press “unlock” button to program) - DEFAULT
When this feature is turned on, if one of the vehicle’s doors is open at the time that
the system is armed via the controller or transmitter, the siren will chirp 3 times and
the parking lights will flash 3 times instead of once.
14
Installer Programmable Features
This group of Installer Programmable Features are all accessed as a group in the second level of
features’ programming. These features have a direct affect upon the system’s operations related
to the installation and vehicle type AND SHOULD ONLY BE CHANGED BY THE INSTALLER!!!
Feature #1 - Remote Start Activation From The WHITE/BLUE Wire
1 pulse (press “lock” button to program) - DEFAULT
2 pulses (press “unlock” button to program)
3 pulses (press “trunk” button to program)
4 pulses(press start” button to program)
This feature changes how the remote start feature is activated from the (-) activation input wire.
Feature #2 - PINK/WHITE (IGN #2) Wire Function
Ignition (press “lock” button to program) - DEFAULT
Accessory(press “unlock” button to program)
Starter (press “trunk” button to program)
This feature changes the operation of the unit’s large PINK/WHITE output wire. This feature
should only be programmed by the installer.
Feature #3 - Engine Detection Method
Tachless Hi
(press “lock” button to program) - DEFAULT
Tachless Lo
(press “unlock” button to program)
Tach Wire
(press “trunk” button to program)
Data Tach
(press “start” button to program)
Crank Only
(press “lock” & “unlock” to program)
This feature selects the method in which the remote start monitors the engine’s running condition
in remote start mode.
“Tachless Hi” sensitivity mode uses a preset crank time (see installer feature #7) and monitors
the vehicle’s voltage level to determine if the engine is running. This setting looks for a voltage
increase of 0.3v after cranking.
“Tachless Lo” sensitivity mode operates like the “Tachless Hi” setting but looks for a voltage
increase of 0.5v after cranking.
“Tach Wire” Before this setting is programmed, refer to the “Violet/White wire” section of the
installation manual for proper wiring connection and the Tach Learn Procedure. It will crank the
engine for up to 3 seconds or until a tach signal is detected.
“Data Tach” mode operates just like the “Tach Wire” setting except it takes its reading from the
D2D data port instead of using the Violet/White wire. Before using, make sure this function is supported by the Databus Interface module.
“Crank Only” AKA “blind start” is similar to the “Tachless” settings however, it only makes one
start attempt and does not monitor engine running conditions. This is useful for many “push-tostart” vehicles.
Feature #4 - Gasoline Or Diesel Engine
Gasoline(press “lock” button to program) - DEFAULT
Diesel 15 Sec. Delay (press “unlock” button to program)
Diesel 20 Sec. Delay (press “trunk” button to program)
Diesel 30 Sec. Delay (press “start” button to program)
This feature changes the system’s timing of the ignition and starter output sequence for gas or
diesel engines. Gasoline: the starter output will occur 3 seconds after the ignitions turn on. When
in “Tachless” mode, the engine running status is determined 10 seconds after starting. Diesel:
the starter output will occur 15, 20, or 30 seconds after the ignitions turn on (allows for glow plug
warming). When in “Tachless” mode, the engine running status will be determined 40 seconds
after cranking.
15
Installer Programmable Features (cont’d)
Feature #5 - Light Relay Function
Dome Light Output (press “lock” button to program) - DEFAULT
Start(press “unlock” button to program)
Ignition Output (press “trunk” button to program)
Accessory Output (press “start” button to program)
Status(press “lock” & “unlock” button to program)
The system has two built-in relays, which can be programmed to perform several different functions. The primary function of this relay, is to operate the vehicle’s dome, or interior lighting as
part of the system’s operations. Optionally, if desired or needed, this relay can be programmed for
the other functions listed above.
Feature #6 Blue Satellite Port, Blue Wire Function
Ignition(press “lock” button to program)
Status / GWR (press “unlock” button to program) - DEFAULT
Defrost Pulse (press “trunk” button to program)
Pulse After Engine Off
(press “start” button to program)
Horn
(press “lock” & “unlock” button to program)
This determines the function of the Blue wire on the Blue satellite relay port.
The Status setting turns on briefly before the Ignition output and stays on during remote start
mode. The other pulse settings give a 0.8 second pulse under the selected condition. Defrost
Pulse will send a pulse after start only when the cabin temperature is below freezing (32 degrees
F / 0 degrees C).
Feature #7 - Starter Cranking Time
0.75 Second
(press “lock” button to program) - DEFAULT
1.00 Second
(press “unlock” button to program)
1.5 Seconds
(press “trunk” button to program)
2.25 Seconds (press “start” button to program)
This feature determines the crank time of the 1st start attempt when in “Tachless” mode. If the
engine doesn’t start on the first attempt, it will retry up to 3 more times extending the crank time by
an additional 0.2 second with each attempt..
Feature #8 - Door Lock/Unlock Outputs
0.8 Second Outputs(press “lock” button to program) - DEFAULT
3 Second Outputs(press “unlock” button to program)
Double Pulse Unlock Output (press “trunk” button to program)
Total Closure Lock Output (press “start” button to program)
This changes the system’s doorlocking outputs to suite different vehicle requirements. The total
closure setting provides a 28 second lock pulse (press LOCK or UNLOCK is during the pulse to
stop it) and a 0.8 second unlock pulse.
Feature #9 Remote Start Lock Control
Off(press “lock” button to program) - DEFAULT
Lock After Start(press “unlock” button to program)
Unlock before start(press “trunk” button to program)
Unlock Before RS & Lock After RS (press “start” button to program)
This feature allows for OEM alarm/lock control in relation to remote start operations thus eliminating extra wiring for OEM alarm control.
16
Installer Programmable Features (cont’d)
Feature #10 - Turbo Timer
Off(press “lock” button to program) - DEFAULT
Run 1 Minute (press “unlock” button to program)
Run 2 Minutes (press “trunk” button to program)
Run 3 Minutes (press “start” button to program)
This feature, the operation of which is described on page 7, when turned on
configures the system to automatically keep the engine running briefly after the key is turned
off. This operation is designed specifically for vehicles with turbocharged engines. NOTE: This
feature is dependent on the proper wiring of the neutral safety circuit.
Feature #11 - Manual Transmission Mode
On
(press “lock” button to program)
Off
(press “unlock” button to program) - DEFAULT
This feature changes the parameters of the system’s remote start operation to be suitable for
manual transmission-equipped vehicles via a “setup” procedure which must be followed upon exiting the vehicle to ensure the transmission is in neutral.
Feature #12 Data Port Protocol
Green: DBI, Black: DBI
(press “lock” button to program) - DEFAULT
Green: iData, Black: iData (press “unlock” button to program)
Green: DBI, Black: iData (press “trunk” button to program)
Green: iData, Black: DBI (press “start” button to program)
This feature determines which data protocol is used on each data port. Choose this based on the
accessory being connected to the port. NOTE: When a BLADE is inserted, this feature automatically switches to the ADS protocol.
Feature #13 - Alarm Functions
On
(press “lock” button to program) - DEFAULT (AL-1660-EDPB)
Off
(press “unlock” button to program) - DEFAULT (RS-360-EDPB)
This feature converts the system into a strictly Keyless Entry/Remote Start System by eliminating
all antitheft alarm-oriented operations and features.
Feature #14 - Pulse Ignition On Disarm
On
(press “lock” button to program)
Off
(press “unlock” button to program) - DEFAULT
This feature will pulse the ignition and activate any attached immobilizer bypass module for
vehicles that require the ignition to be turned on to disarm the OEM alarm.
Feature #15 Lock On Prewarn
On (press “lock” button to program) - DEFAULT
Off (press “unlock” button to program)
This feature will automatically lock the doors to combat unauthorized entry from lock picking when
the prewarn zone is triggered.
Feature #16 - Starter Interrupt Functions
Alarm Only(press “lock” button to program)
Anti-Grind Only(press “unlock” button to program) - DEFAULT (RS-360-EDPB)
Alarm & Anti-Grind (press “trunk” button to program) - DEFAULT (AL-1660-EDPB)
Automatic(press “start” button to program)
Alarm Only - The Starter Interrupt is operable whenever the alarm is armed.
Anti-Grind Only - The Starter Interrupt is operable whenever remote start is on.
Alarm & Anti-Grind - This setting engages starter interrupt when the alarm is armed AND when
the system is in remote start mode. This prevents the starter from grinding if the user accidentally
turns the key to “START” during remote start.
Automatic - This will cause the Starter Interrupt output to automatically engage 90 seconds after
the ignition switch is turned “off”, and after disarming the system.
17
Installer Programmable Features (cont’d)
Feature #17 Low Temp Crank Extender
0ms (Off) (press “lock” button to program)
200ms
(press “unlock” button to program) - DEFAULT
300ms
(press “trunk” button to program)
400ms
(press “start” button to program)
When the vehicle’s interior temperature is below freezing, this feature adds extra crank time to the
base timing (see installer feature #7). It applies to tachless modes only (installer feature #3)
Feature #18 - Arm, Disarm or Additional Channels
Arm / Disarm (press “lock” button to program) - DEFAULT
Arm / Channel 5 (press “unlock” button to program)
Channel 4 / Disarm (press “trunk” button to program)
Channel 4 / Channel 5 (press “start” button to program)
The system has outputs designed for arming and/or disarming a factory-equipped security system.
These wires may be used instead to provide further system outputs, which are remotely operated
by the controller or transmitter. These outputs are in addition to the 2nd channel and 3rd channel
outputs.As shown in the programming assignment, the arm, disarm, channel 4 and channel 5 are
programmable as various combinations. For example, if the disarm output is needed, but not the
arm output, then channel 4 may be made available for use.
Feature #19 - Horn Relay Functions
Horn Output(press “lock” button to program) - DEFAULT
Ignition(press “unlock” button to program)
Trunk Release (press “trunk” button to program)
Pulse After Start (press “start” button to program)
The primary function of this second relay, is to operate the vehicle’s existing horn; either in
conjunction with the electronic siren, or in place of the siren. Using both the siren and the horn
creates an extremely effective security system. Optionally, if desired or needed, this relay can be
programmed for the other functions listed above.
Feature #20 Low Current / Motorcycle Mode
On (press “lock” button to program)
Off (press “unlock” button to program) - DEFAULT
This feature, when on, reduces the system’s current draw by as much as 40% to maximize the
vehicle’s battery life while the alarm is armed. It causes the starter interrupt output to only operate when the ignition is turned on and reduces the frequency of the “armed” flashing status light
significantly. This is ideal when the system is to be used on vehicles that have limited battery
capacity and/or may sit for extended periods without charging the battery.
18
SECURITY
CONVENIENCE
User Feature Programming: Ignition on, off, press valet 5 times
# Feature
Lock Button
(Brake x 1)
Unlock button
(Brake x 2)
Trunk button
(Brake x 3)
Start button
(Brake x 4)
1 Remote Start Run Time
10 min
5 min
15 min
20 min
2 Flashing Light Confirmations
Unlock: ON
RS: ON
Unlock: ON
RS: Flash
Unlock: Flash
RS: ON
Unlock: Flash
RS: Flash
3 Confirmation Chirp Volume
Low
Med-Low
Med-High
High
4 BROWN Wire: Siren / Pulsed Horn
Pulse LOW
Pulse MED
Pulse HI
Steady Siren
5 Ignition Lock / Unlock
Off
Ign On = Lock
Ign. Off = Unlock
Lock + Unlock
6 Door Open Bypass for Feat. #5
On
Off
7 Unlock w/ Trunk Release
On
Off
8 RS Activation (Remote)
Start x 1
Start x 2
Start x 3
Start x 4
9 Last Door Arming
Off
On w/o Lock
On w/ Lock
10 Automatic Rearming
Off
On w/o Lock
On w/ Lock
Enhanced
11 Confirmation Chirps
Siren + Horn
Siren Only
On Demand
Off
12 Anti-Carjacking
Ignition
Door
Ignition + Door
Off
13 Secure Code
Read Page 14 For Programming Instructions
14 Ignition Override
On
Off
15 Alarm Trigger Duration
30 sec
60 sec
90 sec
120 sec
16 Arming Delay
3 sec
15 sec
30 sec
45 sec
17 Open Door Warning Upon Arming
On
Off
4 pulses
Lock + Unlock
(Brake x 5)
INSTALLER ONLY
Installer Feature Programming: Ignition on, off, press valet 10 times
1 RS Activation (WHITE/BLUE wire)
1 Pulse
2 pulses
3 pulses
2 PINK/WHITE Wire
Ignition
Accessory
Starter
3 Engine Detection
Tachless Hi
Tachless Lo
Tach Wire
Data-tach
4 Gasoline or Diesel Engine
Gasoline
15 sec Diesel
20 sec Diesel
30 sec Diesel
5 Light Relay Function
Dome Light
Start
Ignition
Accessory
Status
Pulse After
Engine Off
Horn
6 Blue Sat Port BLUE Wire
Ignition
Status
Pulse After Start
below freezing
7 Crank Time
0.75 sec
1 sec
1.5 sec
2.25 sec
8 Door Lock/Unlock Outputs
0.8 sec
3 sec
Double Unlock
Total Closure
9 Remote Start Lock Control
Off
Lock after
Start
Unlock before
Start
Lock + Unlock
10 Turbo Timer
Off
1 min
2 min
3 min
11 Manual Transmission
On
Off
12 Data Port Protocol
Green: DBI
Black: DBI
Green: iData
Black: iData
Green: DBI
Black: iData
Green: iData
Black: DBI
13 Alarm Functions
On
Off
14 Pulse Ign. on Disarm
On
Off
15 Lock On Prewarn
On
Off
16 Starter Interrupt
Alarm Only
Anti-grind Only Alarm/Anti-Grind
Automatic
17 Low Temp Crank Extender
0 ms
200 ms
300 ms
400 ms
18 Arm/Disarm or CH. 4/5
Arm/Disarm
Arm/CH. 5
CH. 4/Disarm
CH. 4/CH.5
19 Horn Relay Function
Horn
Ignition
Trunk Release
Pulse After
Start
20 Low Current/Motorcycle Mode
On
Off
Crank Only
19
Back Cover
Color cover is in a
separate file.
20