Jøtul GF 370 DV II - Vancouver Gas Fireplaces

WARNING: If the information in these
instructions is not followed exactly, a fire or
explosion may result causing property damage,
personal injury or loss of life.
– Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
– WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call
the fire department.
Jøtul GF 370 DV II
Direct Vent Gas Stove
Installation and
Operation Instructions
– Installation and service must be performed
by a qualified installer, service agency or
the gas supplier.
– In the Commonwealth of Massachusetts,
a carbon monoxide (CO) detector shall
be installed in the same room as the
appliance.
This appliance may be installed in an aftermarket,
permanently located, manufactured home or
mobile home, where not prohibited by local codes.
This appliance is only for use with the types of gas
indicated on the rating plate. A conversion kit is
supplied with the appliance.
Conforms to ANSI Z21.88-2016 • CSA 2.33-2016,
CAN/CGA 2.17-M09, and CSA P.4.1-15
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
139467_12 GF 370 DV II 12/17
THIS OWNER’S MANUAL PROVIDES INFORMATION TO
ENSURE SAFE INSTALLATION AND EFFICIENT, DEPENDABLE
OPERATION OF YOUR FIREPLACE INSERT. PLEASE READ
THESE INSTRUCTIONS IN THEIR ENTIRETY AND MAKE THEM
AVAILABLE TO ANYONE USING OR SERVICING THIS GAS
INSERT.
DO NOT ATTEMPT TO ALTER OR MODIFY THE CONSTRUCTION
OF THIS APPLIANCE OR ITS COMPONENTS. ANY
MODIFICATION OR ALTERATION WILL VOID THE WARRANTY,
CERTIFICATION AND LISTING OF THIS APPLIANCE.
THIS HEATER MUST BE INSTALLED AND MAINTAINED BY A
QUALIFIED SERVICE AGENCY.
Suggested Tools for Installation and Service
•
•
•
•
•
•
•
•
•
•
•
•
External regulator (for Propane only)
Piping which complies with local code
Manual shut-off valve T-Handle required in Massachusetts
Sediment trap - if required by code
Tee joint
• Work Gloves
Pipe wrench
• Safety glasses
Pipe sealant
• Torx T-20 screwdriver
10 mm open end wrench
• Tin snips
1/2”, 7/16” open end wrench
Phillips head screwdriver
Flat head screwdriver
1/4” nut driver
PLEASE NOTE:
It is normal for smoke and odor to occur during
the initial stages of operation, depending upon
temperatures generated over time. This “curing”
condition can be alleviated by promoting fresh
air circulation within the immediate vicinity of
the appliance.
FOR FUTURE REFERENCE....
Fill in the information form on page 38. The stove
serial number will be found on the shipping
carton label and also on the permanent rating
plate attached to the valve compartment.
Use this page to record maintenance records.
Installation Requirements for the
Commonwealth of Massachusetts
THIS PRODUCT MUST BE INSTALLED BY A
LICENSED MASTER OR JOURNEYMAN PLUMBER
OR GAS-FITTER WHEN INSTALLED IN THE
COMMONWEALTH OF MASSACHUSETTS.
1. If there is not one already present, on each
floor level where there are bedroom(s), a
carbon monoxide detector and alarm shall
be placed in the living area outside the
bedroom(s). The carbon monoxide detector
shall comply with NFPA 720 (2005 Edition).
2. A carbon monoxide detector shall:
a) Be located in the room that houses the
appliance or equipment;
b) Be either hard-wired or battery powered
or both; and
c) Shall comply with NFPA 720 (2002
Edition).
3. A Product-approved vent terminal must be
used, and if applicable, a Product-approved
air intake must be used. Installation
shall be in strict compliance with the
manufacturer’s instructions. A copy of
the installation instructions must remain
with the appliance or equipment at the
completion of the installation.
We recommend that
�
our gas products be
installed and serviced by
professionals who are
certified in the U.S. by
the National Fireplace
Institute® (NFI) as NFI Gas
Specialists.
Natural Gas / 70.53%
Propane
/ 63.23%
Based on CSA P.4.1-15
Jøtul GF 370 DV II
2
139467_12 GF 370 DV II
Table of Contents
Installation & Service Tools ...................2
Specifications................................................... 4
General Information........................................5
Safety Information ......................................... 6
Installation
Hearth Requirements ..........................7
Clearances................................................7
Vent Requirements
Approved Vent Manufacturers.......... 8
Vertical Termination............................. 8
Masonry Chimney Conversion........... 9
Horizontal Termination......................10
Vent Termination Clearances.............11
Vent Restriction Adjustments........... 12
Vent Termination Diagram................ 13
Stove Assembly
1. Glass Frame Removal ...................14
2. Routing the Power Supply ..........14
3. Gas Connection...............................14
4. Gas Pressure.................................... 15
5. Fuel Conversion..............................16
6. High Altitude Adjustment...........18
7. Skamol Panel Installation............18
8. Reflective Panel Installation........18
9. River Rock Installation..................19
10. StarFire Glass Installation...........19
11. Log Set Installation......................20
12. Outer Decorative Glass Panels... 21
13. System Check ................................ 22 14. Flame Picture Adjustment...........23
Operation
System Overview ............................... 24
Control Functions.................................25
12/17
Unpacking the Stove
1. Before beginning the installation, inspect the
stove for shipping damage and immediately report
any evidence of damage to your dealer.
2. Confirm stove contents.
The Jøtul GF 370 DV II includes the following loose
items shipped in the Miscellaneous Hardware bag;
• 4 mm hex key - used to remove the •
•
•
•
•
•
front glass panel for access to the firebox.
Remote Control Transmitter
Remote Control Wall Mount Bracket
AA Batteries, 4
Propane Fuel Conversion Kit 156800
Vent Collar Grate Inserts
Enamel Top Plate Shims, 3
3.Remove the Top Plate. Follow the instructions
regarding top plate shims found in the Appendix
on page 30 and fig. 63.
4. Confirm Firebox Components.
Some parts and accessories have been packed in
separate boxes, and include one or more of the
following items:
•
•
•
•
•
Traditional Log Set 156789
StarFire Glass 156815, Clear or 157342, Black
River Rocks 157428
Reflective Glass Panels 156817
Tumbled Stones 157229
5. Remove Pallet Screw. See fig. 1.
6. Safety Screen Barriers: Two side safety barriers
and one front barrier are shipped with the stove.
These must be attached over the glass fire-viewing
panels for protection from hot glass. Engage the
safety barrier mounting tabs over the edges of the
cast iron stove panels.
Maintenance
Annual Cleaning...................................27
Glass Replacement..............................27
Battery Replacement ......................... 28
Accent Lamp Replacement .............. 28
Wiring Diagram .................................. 29
Appendix
Top Plate Shims ..................................30 .
Correct Optional Flame Pictures ....30
Mobile Home Installation.................. 31
Illustrated Replacement Parts............ 32 - 35
Warranty Statement..................................... 36
Lighting Instructions .................................. 39
Figure 1.
Pallet screw location
3
139467_12 GF 370 DV II 12/17
Jøtul GF 370 DV II
Direct Vent Gas Stove
Manufactured and Distributed by:
Jøtul North America
Gorham, Maine USA
Jøtul AS
Fredrikstad, Norway
Test Standards
This appliance complies with
National Safety standards and is
tested and listed by Intertek Testing
Services of Middleton, Wisconsin.
In addition, the Jøtul GF 370
DV II has been tested and listed as
a direct vent gas fireplace heater and listed to
ANSI Z21.88-2016 • CSA 2.33-2016 and
CAN/CGA 2.17-M91.
Specifications
Accessories
Traditional Log Set ................................................ #156789
River Rocks Set .........................................................#157428
Tumbled Stones ..................................................... #157243
StarFire Glass Embers, Black ................................ #157342
StarFire Glass Embers, Clear ................................ #156815
Reflective Glass Firebox Liner .............................. #156817
Fuel Conversion Kit, Propane - 33% TD............. #156800
Fuel Conversion Kit, Natural Gas - 33% TD........#156801
High Altitude Adjustment Kit, NG..................... #156822
Input Rates
Natural Gas
28,000 BTU/hr. maximum input
18,170 BTU/hr. minimum input
Propane
24,000 BTU/hr. maximum input
20,750 BTU/hr. minimum input
Safety Screen
Barriers
Inlet Pressure:
MIN MAX
Natural Gas: 5.0 WC (1.24 kPa) 7.0 WC (1.74 kPa)
Propane: 11.0 WC (2.74 kPa) 13.0 WC (3.24 kPa)
Manifold Pressure: MIN MAX
Natural Gas: 1.6 WC (.398 kPa) 3.5 WC (0.87 kPa)
Propane:
6.4 WC (1.59 kPa) 10.0 WC (2.48 kPa)
• Steady State Efficiency: 74.41% NG / 79.30% LP
• AFUE:
68.01% NG / 68.34% LP
• CSA P4.1-15 Fireplace Efficiency:
70.53 % NG / 63.23% LP
• Intermittent Pilot Ignition ( IPI )
• Continuous Pilot Ignition Mode ( CPI or “standing pilot”) is available.
• Power Requirement: 120 VAC for Fan, Lamp, and Burner Control Module
• Remote Control Transmitter batteries, 3, AAA - 1.5 v
• Remote Control Receiver batteries : 4, AA
• Fan Control Module: 120V / 60 Hz
4
Figure 2. Overall dimensions
139467_12 GF 370 DV II
12/17
General Information
THIS HEATER MUST BE INSTALLED AND
MAINTAINED BY A QUALIFIED SERVICE AGENCY.
DO NOT ATTEMPT TO ALTER OR MODIFY
THE CONSTRUCTION OF THIS APPLIANCE
OR ITS COMPONENTS. ANY MODIFICATION
OR ALTERATION WILL VOID THE WARRANTY,
CERTIFICATION AND LISTING OF THIS APPLIANCE.
WARNING: FAILURE TO POSITION THE PARTS IN
ACCORDANCE WITH THE DIAGRAMS HEREIN
OR FAILURE TO USE ONLY PARTS SPECIFICALLY
APPROVED WITH THIS APPLIANCE MAY RESULT IN
PROPERTY DAMAGE OR PERSONAL INJURY.
IMPORTANT: SAVE THESE INSTRUCTIONS.
1. The installation and repair of this appliance must
be done by a qualified service person. Failure to
properly install and maintain this heater could
result in an unsafe or hazardous installation, which
may result in a fire, explosion, property damage,
personal injury or loss of life.
5. Do not operate this fireplace if any part of it has
been under water..
Immediately call a qualified service technician to
inspect the heater and to replace any part of the
control system and any gas control which has been
under water.
6. Do not operate the fireplace with the glass front
removed, cracked or broken. Replacement of the
glass should be done by a licensed or qualified
service person. Only remove glass for routine
service. Always handle glass carefully.
Pour utilisation avec les portes en verre cerifiers
aved l’appareil seulemend ou. Ne pas utiliser avec
des portes on verre.
7. Notify your insurance company before proceding
with installation of this fireplace.
2. This appliance should be inspected before use and
at least annually. More frequent cleaning may
be required due to excessive lint from carpeting,
bedding material, etc. It is imperative that control
compartments, burners and circulating air
passageways of the appliance be kept clean.
3. This appliance may be installed in an aftermarket
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by local
codes.
This appliance is only for use with the type(s) of
gas indicated on the rating plate. This appliance is
not convertible for use with other gases, unless a
certified kit is used.
4. The installation must conform to local codes. Your
local Jøtul authorized dealer can assist you in
determining what is required in your area for a safe
and legal installation. Some areas require a permit
to install a gas burning appliance. Always consult
your local building inspector or authority having
jurisdiction to determine what regulations apply in
your area.
In the absence of local codes, the installation
requirements must comply with the current
National codes. In the U.S., these requirements
are established in the National Fuel Code, ANSI
Z223.1.(NFPA 54). In Canada, the codes have been
established in CAN/CGA B149 Fuel Installation Code.
5
139467_12 GF 370 DV II 12/17
Safety Information

Due to the high operating temperatures this
appliance should be located out of traffic and
away from furniture and draperies. Maintain
proper clearance to combustible mantels and
fireplace trim.

Children and adults should be alerted to the
hazards of high surface temperatures and should
stay away to avoid burns or clothing ignition.

Young children should be supervised while they
are in the same room as the appliance. Toddlers,
young children and others may be susceptible
to accidental contact burns. A physical barrier,
such as a child guard, is recommended to be used
if there are at-risk individuals in the house. To
restrict access to a fireplace or stove, install an
adjustable safety gate to keep toddlers, young
children and other at-risk individuals out of the
room and away from hot surfaces.

A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and shall be installed for the protection
of children and other at-risk individuals.

If the barrier becomes damaged, the barrier shall
be replaced with the manufacturer’s barrier
for this appliance. See fig. 72, page 34 for part
numbers.

Any safety screen, guard, or barrier removed for
servicing an appliance must be replaced prior to
operating the appliance.

Clothing or other flammable materials should not
be placed on or near the fireplace.

Never allow anyone to use the fireplace if they are
unfamiliar with its operation.

NEVER store or use gasoline or any other
flammable vapors or liquids in the vicinity of this
appliance.

Never burn any solid materials (wood, cardboard,
paper, coal, etc.) in this appliance. Use with natural
gas or propane fuel ONLY.

Do not slam or strike the glass panel.

This appliance is NOT for use with aftermarket glass
doors.

Wear gloves and safety glasses while installing
or performing maintenance procedures on this
appliance.
6
WARNING!
Shock Hazard. Can cause severe injury or death.
This appliance is powered by line voltage. Do not
try to repair the components in this appliance.
In no way are the component enclosures to be
tampered with or opened. Disconnect from line
voltage during installation or performing any
maintenance.
ATTENTION!

Shut off the main gas supply to the appliance
during receiver or remote control battery
replacement.

Always shut off the main gas supply to the
appliance during inspection, maintenance, or
cleaning.
Electrical Hazards

Be aware of electrical wiring locations when cutting
holes in walls and ceilings for termination.

This appliance power supply must be electrically
grounded in accordance with local codes or,
in the absence of local codes, with the current
ANSI/NFPA 70, National Electrical Code or CSA
C22.1-Canadian Electrical Code.

This appliance power supply incorporates a
three-prong (grounding) plug for protection
against shock hazard and should be plugged
directly into a properly grounded three-prong
receptacle. DO NOT CUT OR REMOVE THE
GROUNDING PRONG FROM THE PLUG.

Do not disconnect the lamp and fan power cords
from the appliance power supply (Fan Control
Module). Use the rocker switch to control power
to these parts.

Always disconnect (unplug) the main power
supply from its outlet when performing routine
service on this appliance.
139467_12 GF 370 DV II
Installation
12/17
Stove and Vent Clearance
Requirements
Stove Location
In selecting a location for the stove, consider the
following points:
1) Heat distribution
2) Vent termination requirements
3) Gas supply routing
4) Traffic areas, furniture, draperies, etc.
5) 120V electrical outlet availability
This stove may be located on or near conventional
construction materials, however, proper clearance to
combustibles must be maintained in order to provide
adequate air circulation around the appliance. Also, it
is important to provide adequate access around the
stove for servicing and proper operation.
The clearances specified in this manual are the
minimum requirements established as a result of
safety testing. A combustible material is anything
that can burn; i.e. sheet rock , wall paper, wood,
fabrics, etc. These surfaces are not limited to those
that are visible and also include materials that may
be located behind non-combustible materials.
If you are not sure of the combustible nature
of a material, consult your local fire officials. “Fireresistant” materials are considered to be combustible.
They may be difficult to ignite, but will burn. “Fire
-rated” sheet rock is also considered combustible.
Hearth Requirements
Clearance is measured from the stove body as
illustrated - not the Safety Barriers.
Minimum Clearances: See figs. 3-5.
Rear:
3” (76 mm) - from Rear of the unit
Corner:
5” (127 mm) - from Stove Top
Ceiling:
Sides: 16 3/4” (425 mm) - from Stove Top
7” (178 mm) - from Stove Top
Minimum Clearances from the Vent Pipe
to Combustibles:
Horizontal Run:
Off the top of the pipe - 2” (51 mm) Alcove - 7” (178 mm)
Off the sides and bottom - 1” (25 mm)
Vertical Run: All sides
- 1” (25 mm)
Figure 4. Alcove and Wall Clearances.
The Jøtul GF 370 DV II has been approved for
installation directly on combustible floor materials,
including carpeting. No additional floor protection is
required, however, we recommend that the stove be
installed on a solid surface.
ALCOVE SPECIFICATIONS:
Maximum Alcove Depth:
21 3/4” (55.2 cm)
Minimum Alcove Width:
31 1/4” (79.3 cm)
Minimum Ceiling Height: 62 1/4” (158.1 cm)
Figure 3. Corner Clearances.
Figure 5. Parallel Wall Clearances.
7
139467_12 GF 370 DV II 12/17
Venting Requirements
There are three types of venting configurations
approved for use with this appliance:
• Vertical Venting / Vertical Termination
• Vertical Venting / Horizontal Termination
• Horizontal Venting / Snorkel Termination
This appliance is approved for use with the 4/6
direct vent systems manufactured by the companies
listed on page 8. Use parts of one manufacturer only
- DO NOT MIX VENT COMPONENTS FROM DIFFERENT
MANUFACTURERS WITHIN THE SAME SYSTEM.
Installation of any components not
manufactured or approved by Jøtul or failure to meet
all clearance requirements will void all warranties
and could result in property damage or bodily injury.
The approved vent configurations described
in this manual are derived from extensive testing
under controlled laboratory conditions. Gas
appliance performance can be negatively affected
by variables present in the installation environment,
i.e.; atmospheric pressure, strong prevailing winds,
adjacent structures and trees, snow accumulation,
etc. These conditions should be taken into
consideration by the installer and stove owner when
planning the vent system design.
Approved Vent Manufacturers
The Jøtul GF 370 DV II stove is approved for
installation with direct vent chimney components
supplied by the following manufacturers:
M&G DuraVent, Inc. (Direct Vent Pro Series)
P.O. Box 1510
Vacaville, CA 95696-1510
800-835-4429
Selkirk Corporation
1301 W. President George Bush Hwy, Suite 330
Richardson, TX 75080-1139 800-992-8368
American Metal Products (Amerivent)
8601 Hacks Cross Rd.
Olive Branch, MS 38654 800-423-4270
Security Chimneys International Limited
2125 Monterey, Laval, Québec
Canada, H7L 3T6
450-973-9999
Metal-Fab, Inc.
P.O. Box 1138
Wichita, KS 67201
316-943-2351
ICC, Inc.
400 J-F Kennedy St. Jerome, Quebec
Canada, J7Y 4B7
450-565 6336
IMPORTANT
• JOINT SEALING
REQUIREMENT:
APPLY A 1/8” BEAD OF
HIGH-TEMPERATURE
SEALANT OR MIL
PAC® TO THE MALE
SECTION OF THE
INNER VENT PIPE. THE
Figure 6.
CEMENT SHOULD
FORM A SEAL BETWEEN
THE INNER AND OUTER PIPES. DO NOT USE SILICONE.
SEE FIG. 6. SEE VENT MANUFACTURER’S INSTRUCTIONS.
• NEVER MODIFY ANY VENTING COMPONENT, OR
USE ANY DAMAGED VENTING PRODUCT.
• THE GAS APPLIANCE AND VENT SYSTEM MUST
BE VENTED DIRECTLY TO THE OUTSIDE OF THE
BUILDING AND NEVER ATTACHED TO A CHIMNEY
SERVING A SOLID FUEL OR GAS BURNING
APPLIANCE. EACH DIRECT VENT GAS APPLIANCE
MUST HAVE ITS OWN SEPARATE VENT SYSTEM.
COMMON VENT SYSTEMS ARE PROHIBITED.
• IF VENTING SYSTEM IS DISASSEMBLED FOR ANY
REASON, REINSTALL PER THE MANUFACTURER’S
INSTRUCTIONS PROVIDED FOR THE INITIAL
INSTALLATION.
Vertical Venting and Termination
The Jøtul GF 370 DV II can be vertically vented
through a roof or ceiling. Follow these guidelines
Steep roofs, nearby trees, or predominantly windy
conditions, can promote poor draft or down
draft conditions. In such cases, an increase to the
height of the vent may improve performance.

If an offset or elbow is necessary in the vertical
rise, the vent pipe must be supported every three feet
to avoid excessive stress on the offsets. Use listed Wall
Straps from any of the approved vent suppliers.

A maximum of two 90° or four 45° elbows may be
used in a vertical termination. Whenever possible,
use 45° elbows instead of 90° elbows as they
offer less restriction to the flow of flue gases and
intake air.

A listed firestop is required at any floor
penetration. The opening should be framed in
according to the manufacturer’s instructions.
Bernard Dalsin Manufacturing Co. (Pro Form)
5205 208th Street West
Farmington, MN 55024
651- 460-1080

Always maintain a minimum 1" clearance from
Olympia Chimney Supply Inc.
600 Sanders Street Suite 2
Scranton, PA 18505-3400

Minimum vertical termination height: 6 ft. of
8
570-496-8890
all sides of the vertical vent system to any
combustible material.
vent pipe.
Horizontal Overhang
18”.
min.
Termination
Cap
18”.
min.
Vertical Wall
139467_12 GF 370 DV II
12/17
#991 Vertical Termination Cap
Cap Adaptor-
Exhaust Gas
Lowest Discharge
Opening
Intake Air
18” min.
Figure 7. Minimum roof penetration height and clearance
from adjacent surfaces - vertical
termination.

IT IS NECESSARY to add restriction to a vertical vent
installation to compensate for excessive draft. See
page 13; Exhaust Restriction Adjustment.

GAS VENT HEIGHT: In no case shall any discharge
4” Flex Pipe
not included
in kit
Support/Wall
Thimble Cover
Use Standard
Simpson DuraVent GS Pipe
from stove to
thimble
opening on the cap be less than 18” (457 mm) horizontally from the roof surface. See fig. 7.

Maximum Vent Height: 35 ft. above the appliance.
Masonry or Prefabricated Chimney
Conversion
The GF 370 DV II is approved for use with direct vent
chimney conversion kits in a masonry chimney or
a prefabricated solid fuel listed chimney. These are
available from most of the manufacurer’s listed on
page 8.
The following installation requirements must be
followed:
1. Use the restrictor zone guidelines in the Vent
Window Diagram, fig. 17. In masonry chimney, a
fireclay liner or listed steel liner, must be contained
within the entire length of the chimney.
3. Overall venting should not exceed 35 ft. (10.67 m).
4. The liner must have an inside dimension of 6”
round or greater.
5. Prefabricated chimneys must be UL 103 or ULC
S-629 listed and have a minimum INSIDE diameter of 6 inches, (150 mm). Prefabricated chimneys
must be listed for the specific manufacturer’s
conversion kit.
Figure 8. Vent System through a masonry chimney
using the Simpson Dura-Vent Chimney Conversion Kit
46DV IIA-KMC and 46DV IIA-KCT components. Other
manufacturers use similar designs. Conversion kits
are also available for use with listed prefabricated
chimneys.
IMPORTANT NOTICE
THE USE OF AN EXISTING CHIMNEY AS
AN AIR INTAKE IS NOT COVERED UNDER
THE ANSI Z21.88-1999-CSA 2.33-M99
TEST METHODS AND RESULTING ITS/
WHI PRODUCT CERTIFICATION. THE CODE
AUTHORITY HAVING JURISDICTION MUST
BE CONSULTED PRIOR TO PROCEEDING WITH
THIS INSTALLATION METHOD.
9
139467_12 GF 370 DV II 12/17
Horizontal Termination
 Minimum vertical rise from the vent collar is a 24”
section vent pipe. See fig. 9. Minimum horizontal
run is 12” with natural gas and 18” with propane.
Figure 9. Minimum vent
pipe sections required for
horizontal termination:
A = 12” with NG
18” with LP

A maximum of two 90° or four 45° elbows may
be used in a horizontal termination. Whenever
possible, use 45° elbows instead a 90° elbow as
they offer less restriction to the flow of flue gases
and intake air. Reduce the overall horizontal run
by 5 feet for each additional elbow, whether 45° or
90°.
Listed Wall
Thimble

Snorkel Termination - ( 14” or 36”):
NATURAL GAS ONLY. DO NOT USE SNORKEL
TERMINATION WITH PROPANE FUEL.
A horizontal vent run may be made with a 90°
elbow directly to the rear of the stove only when
terminated by a 14 or 36 inch snorkel cap. Fig. 10
shows the minimum vent pipe requirements.
14” Snorkel: The maximum horizontal vent run
must not exceed a 24” section of pipe and must be
a minimum of 12”.
36” Snorkel: The maximum horizontal vent run
must not exceed 5 feet and must be a minimum
of 12”.
Figure 10. Minimum vent
pipe sections required for a 14”
Snorkel termination - Natural
Gas ONLY.
.

The termination cap must not be recessed into
the wall or siding. Do not fill air space in wall around
termination cap with any type of insulation.

Wall Cut-out: A minimum 10” X 10” square hole
is adequate for proper pipe clearance through a
wall, provided the vent is positioned to maintain
2” minimum clearance at the top. A 1” minimum
clearance must be maintained to combustible
material around the other sides. See fig. 11.
Listed Wall
Thimble
NG
ONLY

Any horizontal run of vent must have a 1/4” rise for
every foot of run toward the termination cap.

All horizontal terminations must comply with the
clearance specifications to adjacent structures as
indicated in fig. 12.

Installation of a Vinyl Siding Standoff is required
to prevent damage to vinyl siding between the
vent cap and the exterior wall.

A horizontal termination cap must maintain a 3”
clearance to any overhead combustible projections that
are 2 1/2” or less. It must also maintain a 12” clearance
from projections that exceed 2 1/2”. See fig. 13.
Vinyl siding projections require a default clearance of
18” to the vent terminal.
10
Figure 11. Install a
listed wall thimble
according to manufacturer’s instructions
to maintain required
clearance to combustible materials.
139467_12 GF 370 DV II
12/17
Horizontal Termination Clearance
Figure 13.
Termination Clearance
to overhangs.
Figure 12. Vent Terminal Clearances - ANSI Z21.88-2014, CSA 2.33-2014, and National Fuel Gas Code.
Canadian Installations 1
U.S. Installations 2
A
Clearance above grade, veranda, porch, deck,
or balcony
12 in. (30 cm)
12 in. (30 cm)
B
Clearance to window or door that may be
opened
12 in. (30 cm)
9 in. (23 cm) We recommend 12 in. to prevent
condensation on a window.
C
Clearance to permanently closed window
12 in. (30 cm)
9 in. (23 cm) We recommend 12 in. to prevent
condensation on a window.
D
Vertical clearance to ventilated soffit located
above the terminal within a horizontal
distance of 2 ft (60 cm) from the center line
of the terminal
18 in, (46 cm)
18 in, (46 cm)
E
Clearance to unventilated soffit
12 in,. (46 cm)
12 in,. (46 cm)
F
Clearance to outside corner
12 in,. (46 cm)
9 in. (23 cm) We strongly recommend 12 in.
particularly where strong winds prevail.
G
Clearance to inside corner
12 in,. (46 cm)
9 in. (23 cm) We strongly recommend 12 in.
particularly where strong winds prevail.
H
Clearance to each side of center line
extended above a gas meter or regulator
I
Clearance to service regulator vent outlet
3 ft. (91 cm) within a height 15 ft. above the
meter/regulator assembly
*
3 ft. (91 cm)
*
J
Clearance to nonmechanical air supply inlet
to building or the combustion air inlet to
any other appliance
12 in. (30 cm)
9 in. (23 cm)
K
Clearance to a mechanical air supply inlet
6 ft. (1.83 m)
L
Clearance above paved sidewalk or paved
driveway located on public property
7 ft. (2.13 m) 3
*
M
Clearance under veranda, porch, deck, or
balcony
12 in. (30 cm) 4
12 in. (30 cm) 4
N
Clearance to propane tank relief valve and
filler connection
5 ft. (1.52 m) 5 / 10 ft. (3.05 m) 6
5 ft. (1.52 m) 5 / 10 ft. (3.05 m) 6
1) In accordance with the current CSA B149.1, Natural Gas and Propane
Installation Code.
2) In accordance with ANSI Z223.1/NFPA 54, National Fuel Gas Code
*
For clearances not specified in ANSI Z223.1/NFPA or CSA B149.1, the
clearance will be in accordance with local installation codes and the
requirements of the gas supplier.
3 ft. (91) cm above if within 10 ft. (3 m)
horizontally
3) A vent shall not terminate directly above a sidewalk or driveway
which is located between two single family dwellings and serves both
dwellings.
4) Permitted only if veranda, porch, deck, or balcony is fully open on a
minimum of two sides beneath the floor.
5) Minimum clearance to tanks not filled on site.
6) Minimum clearance to tanks filled on site from bulk truck.
11
139467_12 GF 370 DV II 12/17
Vent Restriction Adjustments
The Jøtul GF 370 DV II features adjustment controls for
both intake air and exhaust to accommodate a variety
of conditions that result from variables inherent in the
vent configuration and environment. Both controls
can be accessed from outside the firebox to allow the
burner to be “dialed-in” under operation. See figures 14
and 16.
Use the Vent Termination Diagram, fig. 17, to
determine which zone your vent termination falls
within and make the appropriate exhaust and air
intake setting adjustments. Use these settings as
general guidelines to start from. The final settings
will ultimately be determined by the individual
characteristics of your particular installation.
There are no hard and fast rules.
Exhaust Vent Restriction
Exhaust restriction prevents overly strong draft
that can interfere with pilot function, cause poor
combustion or a weak flame picture. The shutter is
set in the fully open position at the factory. The final
position of the restriction shutter is determined by
where the vent termination falls within the vent
window diagram.
For example, if the vent rise is 20 feet and
includes one elbow in a horizontal run of 5 feet, the
appropriate exhaust setting will be Full Restriction.
Exhaust Restrictor Adjustment
1. Remove the Trim Rings from the Top Plate.
2. Loosen the locking screw and turn the restrictor
pivot plate to the appropriate indicator point as
specified in the vent window diagram, figure 17.
After the burner has been operating for 15 minutes,
make any further adjustment in 1/8” increments
until the desired flame picture is achieved. Do not
exceed the fully closed setting as shown in fig. 15.
Operate the burner for 10-15 minutes between additional adjustments.
3. Tighten the locking screw and replace the Trim
Rings.
Intake Air Adjustment
An Intake Air shutter plate allows further burner
adjustment for taller vent runs. It is located under the
firebox floor and is set fully open at the factory. See
fig. 16.
The shutter has an adjustment range of 1 inch.
To change the setting, loosen the wingnut and slide
the gasketed shutter stem backward to the half or
fully closed positions, depending on which vent zone
is appropriate. Retighten the wingnut before lighting
the burner to seal the gasket. Allow the flame pattern
to settle in for 10- 15 minutes between each setting
change.
Zone D
Top Plate
Vent terminations within Zone D are susceptible
to draft conditions that may interfere with the
intermittent Pilot Ignition functionality. In such
cases, we recommend that the stove be operated
only in Continuous Pilot Ignition mode. Pivot Plate
Figure 14. The Exhaust Restrictor is located within the
vent adaptor collar.
Air Intake Shutter
Stem
Figure 15. Exhaust Restrictor settings
12
Figure 16. Air intake shutter location.
139467_12 GF 370 DV II
two 90° or four 45°
elbows may be used.
Whenever possible,
use 45° elbows instead
of 90° elbows as these
offer less restriction to
the flow of flue gases
and intake air. Use of
elbows may adversely
affect IPI functionality.
In such cases, CPI
mode should be used.

Reduce the overall
horizontal run by 5 feet
for each additional 45°
and 90° elbow.

When two or more
elbows are used in a
horizontal run, a less
restricted setting may
be more effective
than that indicated by
the termination zone
diagram.




A maximum of
12/17
Intake Air - Fully Closed
Full Exhaust Restriction

Intake Air - Half Closed
Half Exhaust Restriction

­
Intake Air - Fully Open
No Exhaust Restriction
ANY VENTING WITH A VERTICAL RISE MUST
TERMINATE (END) WITHIN THE SHADED AREAS.
Figure 17 . Vent Termination Diagram.
13
139467_12 GF 370 DV II 12/17
Stove Assembly
1. Glass Frame Removal
To access the firebox, use the 4 mm hex key to
remove the four socket head screws that attach the
glass frame to the firebox. See fig. 18.
• Remove the labeled lower skamol retainer from
the firebox and discard.
2. Routing the Power Supply
The power cord located in the valve compartment is
connected to the Fan Control Module which is the
main power supply for all stove operating functions.
Route the cord through the pedestal and out the rear
of the pedestal base as in fig. 18, or through the floor.
CAUTION: Take care that the pedestal base does not
pinch the power cord. You should be able to feel free
play in the cord.
The 10 foot extension power cord, supplied in
the hardware bag, is intended to connect the interior
cord to the nearest 120V house current outlet.
Figure 18.
Glass frame
removal.
DO NOT CONNECT THE STOVE TO HOUSE CURRENT UNTIL THE INSTALLATION IS COMPLETE AND
YOU ARE READY TO INITIATE THE FIRST BURN.
3. Connecting the Gas Supply
Gas Supply Requirements
ALL INSTALLATIONS MUST COMPLY WITH LOCAL
CODE OR IN THE ABSENCE OF LOCAL CODE, MUST
COMPLY WITH THE MOST RECENT EDITION OF THE
NATIONAL FUEL GAS CODE ANSI Z223.1/NFPA 54 OR
CAN-B149.
THIS PRODUCT MUST BE INSTALLED BY A
LICENSED MASTER OR JOURNEYMAN PLUMBER
OR GAS-FITTER WHEN INSTALLED IN THE
COMMONWEALTH OF MASSACHUSETTS.
Shut-off Valve
All codes require a gas shut-off valve (gas
cock) and union to be installed in the supply line
within 6 feet of the appliance. This allows for
the disconnection of the stove for servicing and
maintenance. See Fig. 19.
A T-HANDLE GAS SHUT-OFF VALVE IS REQUIRED IN MASSACHUSETTS IN COMPLIANCE
WITH CODE 248CMR.
14
The stove and gas control valve must be disconnected from the gas supply piping during any pressure testing of the system at test pressures in excess
of 1/2 psig. For pressures lower than 1/2 psig, isolate
the gas supply by closing the manual shut-off valve.
Control Valve Connection
The gas supply line connection to the stove flex
line can be made at the rear of the base plate or
through the floor. The gas supply line should be a
minimum 3/8” inside diameter, or the appropriate
size to provide sufficient gas pressure to the valve
regardless of the input setting.
The use of flexible gas appliance connectors
is acceptable in many areas in the U.S. In Canada,
methods vary depending on local code. If local codes
permit, use flexible gas line for ease of installation
and service. For those locales where flexible gas lines
are not permitted, use the 3/8” iron fitting to make
the connection at the top side of the Control Valve.
See fig. 19.
Secure all joints tightly using appropriate tools
and sealing compounds (for propane units, be sure to
use compounds that are propane resistant). Turn on
gas supply and test for gas leaks using a 50/50 soapy
water solution or a gas detector.
139467_12 GF 370 DV II


12/17
Inlet Pressure
MIN MAX
Natural Gas: 5.0 WC (1.24 kPa)
7.0 WC (1.74 kPa)
Propane: 12.0 WC (2.99 kPa) 14.0 WC (3.48 kPa)
Manifold Pressure
MIN MAX
Natural Gas: 1.6 WC (0.398 kPa)
3.5 WC (.87 kPa)
Propane:
6.4 WC (1.59 kPa) 10.0 WC (2.48 kPa)


Figure 19. Gas supply valve types and fittings.
NEVER USE AN OPEN FLAME TO CHECK FOR GAS
LEAKS.
ALWAYS REFER TO THE LIGHTING INSTRUCTIONS
ON THE INSIDE BACK COVER OF THIS MANUAL
WHEN LIGHTING THE STOVE.
Soap Solution Leak Test
• Mix a 50-50 solution of water and dish soap.
• Light appliance - see lighting instructions on the
back cover of this manual or on the rating plate.
• Brush or spray all joints and connections with the
soapy water solution.
• If bubbles appear at any connection or seam or a
gas odor is detected, immediately turn gas control
knob to the OFF position.
Tighten or reconnect the leaking joint and retest
for any gas leaks.
4. Testing Gas Pressure
Proper gas pressure provides a consistent flow of gas
to the appliance and is instrumental in checking for
gas leaks. There are two pressure test points on the
front of the stove control valve where test gauge connections are made. See Fig. 20. Gauge connections
are identified by:
• E for inlet or supply pressure ( the amount of gas
coming to the valve.)
• A for manifold pressure (the amount of gas that is
coming out of the valve to the burner.)
The line must be disconnected from the gas
supply line by closing the main supply manual gas
shut-off valve (gas cock) during any pressure testing
of the gas supply piping system that is equal to or
exceeds pressures of 1/2 psig (3.5 kPa).
ALWAYS TEST PRESSURES WITH VALVE REGULATOR
CONTROL AT THE HIGHEST SETTING.
Symptoms of incorrect gas pressure include:
Insufficient gas pressure:
• Small pilot flame which can result in insufficient
millivolts.
• Little variation in flame picture between HI and LO
regulator settings.
• Insufficient gas to support more than one appliance causing nuisance outages or gas surges.
Excessive gas pressure:
• Permanent damage to valve causing complete appliance shut down.
• Too large a pilot flame resulting in overheating of
the power generator and consequent shut down.
• Sooting due to impingement and/or incorrect fuel
to air mix.
A
Manifold
E
Inlet
Pilot Adjustment
Figure 20. Pressure test points located on the front
of the valve.
WARNING
DO NOT ALLOW THE INLET GAS PRESSURE TO
EXCEED 14.0” WC (OR 1/2 PSIG) AS SERIOUS
DAMAGE TO THE VALVE MAY RESULT.
15
139467_12 GF 370 DV II 12/17
5. Fuel Conversion
The GF 370 DV II gas stove is shipped from the factory
equipped to burn Natural gas. Propane fuel conversion kit 156800 is included with the stove to enable
use with LP gas if necessary. The kit contains all the
components needed to complete the task and ensure
safe operation, including labels that must be affixed
to the stove.
CAUTION: Before proceeding with this conversion,
the gas supply must be shut off prior to disconnecting
the electrical power.
This conversion kit shall be installed by a qualified
service agency in accordance with the manufacturer’s
instructions and all applicable codes and requirements
of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire,
explosion, or production of carbon monoxide may result
causing property damage, personal injury or loss of life.
The qualified service agency is responsible for the proper
installation of this kit. The installation is not proper and
complete until the operation of the converted appliance
is checked as specified in the manufacturer’s instructions
supplied with the kit.
Cet équipement de conversion sera installé par une
agence qualifiée de service conformément aux instructions du fabricant et toutes exigences et codes applicables de l’autorisés avoir la juridiction. Si l’information
dans cette Instruction n’est pas suivie exactement, un
feu, explosion ou production de protoxyde de carbone
peut résulter le dommages causer de propriété, pert ou
blessure personnelle de vie. L’agence qualifiée do service
est esponsable de l’installation propre de cet équipemetn. L’installation n’est pas propre et complète jusqu’à
l’operation de l’appareil converi est chéque suivant les
critères établis dans les instruction de propriétaire provision nées avel l’équipement.
Conversion Kit
(LP #156800, NG #156801)
Tools required:
• 1/2” & 13 mm open end wrench or deep-well socket
• Torx T20 or slotted screwdriver
• 7/16” open end wrench • 1/4” nut driver
• 4 mm allen wrench
• Label B - apply to the rating plate in the space indicated on the plate.
• Small valve label - apply to valve body
• Conversion instructions
Fuel Conversion Procedure
1. Turn off gas supply to the stove and disconnect
from electrical power source.
2. Remove the glass frame. See fig. 18.
3. Loosen the primary air shutter wingnut and push
the stem all the way back. Fig. 21.
Figure 21.
Figure 21. Air Shutter location.
4. Pull the Burner Plate forward to disengage it from
the burner orifice and lift it out of the firebox.
5. Locate the main burner injector. See fig. 23 on
page 17. Slide the Air Shutter out of the way and
use a 1/2” open end wrench or deep-well socket to
remove the burner orifice from the brass orifice
holder. Replace with the orifice supplied in the
kit. Tighten securely.
6. Change the Air Shutter position: Lift the shutter
tube up in its hinge pin slots and turn the tube
over, so that the appropriate fuel type indicator
(LP or NG) is oriented facing you. See fig. 22. Push
the shutter all the way back over the injector.
7. Change the Dual-fuel Pilot Orifice. Use a 7/16”
wrench to just loosen the pilot base enough to
push the orifice lever to the left for LP, exposing
the red indicator. Retighten the base. See fig. 23.
Conversion Kit Contents:
• 1 regulator tower labeled for the appropriate fuel
• 2 regulator tower Torx screws
• 1 burner injector (#38 mm for NG, #53 for LP)
• Label A - to be completed and applied to the base
of the valve compartment
16
Figure 22. Primary air shutter orientation must be
changed for fuel type.
139467_12 GF 370 DV II
12/17
Pilot Hood
Ignitor
Flame Sensor
Primary Air
Shutter
Orifice Lever
Injector
Regulator
Diaphragm
IFC Reset Button
el
Apply Lab
“A” Here
Regulator
Tower
Use new Torx
screws supplied
Figure 23. Fuel conversion components and assemblies
8. Reinstall the Burner Plate by engaging the
venturi tube with the Air Shutter. BE CERTAIN
THE BURNER IS LEVEL AND SECURELY SEATED ON
THE SUPPORT LEGS ON THE FIREBOX FLOOR.
9. Replace the variable regulator. Using a Torx T-20
screwdriver, remove the two specialty screws
from the regulator tower on the front of the
valve. Note: To help identify which screws to remove,
refer to the new regulator in the kit. See fig. 23.
10. Disconnect the Regulator wire lead from
the receptacle housing terminal. Remove the
regulator tower and the rubber diaphragm.
11. Install the new variable regulator tower from the
kit. Be sure that the gasket is properly positioned
and tighten screws securely. Connect the wire
lead.
12 . Apply the identification labels to the stove so that they can
be seen by any person that may be servicing the stove.
• Label “A”: Apply to front lip of the valve compartment.
• Label “B”: Apply to the Rating Plate.
• Small valve sticker: Apply to valve.
13. Install the accessory panels and burner media as
appropriate. See pages 19-21.
14. Apply anti-seize lubricant to the socket head glass
frame screws before reinstalling the glass frame.
15. Apply gas to the system and check for leaks using
a soapy water solution or gas sensor.
16.Follow the System Check instructions on pages 22-23
for initial start-up and flame picture adjustment.
17
139467_12 GF 370 DV II 12/17
6. High Altitude Adjustment
The decreased atmospheric pressure of higher altitudes affects heat value of gaseous fuels. Most gas
suppliers derate the gas intended for use at elevations above 2000 feet. Check with your gas supplier
before performing derate adjustment to the burner.
This appliance may be adjusted for altitude over
2000 ft. (610 - 1371 m) for natural gas.
If the gas supplier does not derate fuels, install High
Altitude Adjustment Kit 156822 for Natural gas.
7. Firebox Panel Installation
Skamol Panels and optional
Reflective Glass Kit 156817
Skamol Panels
These insulating panels are installed at the factory.
If desired, the panels may be painted black using any
high-temperature paint.
DO NOT DERATE FOR PROPANE.
THE SKAMOL PANELS MUST BE LEFT IN PLACE.
DO NOT OPERATE THE STOVE WITHOUT THE SKAMOL
PANELS INSTALLED.
U.S & Canada per
ANSI Z21.88-2005•CSA 2.33-2005, CAN/CGA 2.17
Reflective Glass Panels
For natural gas installations from 610-1370 meters
(2000-4500 ft.) the orifice size (DMS) is #39. See
data plate for additional information. For high
altitude installations consult the local gas distributor
or the authority having jurisdiction for proper rating
methods. If the installer must convert the unit to
adjust for varying altitudes, the information sticker
must be filled out and applied to the appliance at the
time of the conversion.
Cet appareil est equippé pour des altitudes compries
entre 0 et 2000 pieds (0-610 m ) seulement.
Derating Procedure
• Follow Steps 1-6 of the Fuel Conversion procedure
on pages 16 to change the burner injector. Use the
injector supplied with the kit. Detailed instructions are also included in the kit.
• Conduct gas leak and gas pressure tests as detailed on page 15 of this manual.
• Conduct system check and flame picture adjustments as specified on pages 22-23.
INSTALLER: Fill out the appropriate information
and apply the high altitude conversion label provided to the rating plate on the appliance. See fig. 24.
This appliance has been converted for use at an
altitude of___________ .
Orifice Size: __________ Manifold Press. _______
Input Btu/Hr. _________ Fuel Type ___________
Date: ___/___/___ Converted by:_____________
Cet appreeil a été converti au _____ Injecteur_____
Pression à la tubulure d’alimentation ___________
Déoit calorifique ___________
Figure 24. High Altitude Conversion Label.
18
Tools: 1/4” socket driver
Optional: High-temp Black Paint may be applied
to the exposed edges of the side Skamol panels to
match the black glass.
Cotton gloves are provided with the glass panels. Use
them to handle the panels to prevent fingerprints on
the surfaces. Fingerprints are difficult to remove. Use a
clean cloth to remove any dust from the glass panels.
1. Remove the Upper Retainer Bracket from the
firebox with removal of three #8 x 12 sheet metal
screws. See fig. 25.
2. Remove the Lower Panel Retainer from the back
of the burner skirt with removal of three #8 x 12
sheet metal screws.
3. Orient the rear panel, smooth side out, textured
side in. Rest the bottom of the panel on the burner
skirt, centered against the back wall. See fig. 26.
4. Orient the side panels, smooth side out, and sliding
each behind the retainer wings. See Fig. 26a.
5. Push the Upper Retainer back against the glass
panels and tighten the three sheet metal screws.
6. Replace the Lower Panel Retainer.
139467_12 GF 370 DV II
12/17
8. Install Burner Media
River Rocks
CAUTION: THE ROCKS ARE FRAGILE! SUPPORT THE
ASSEMBLY FROM THE BOTTOM AND HANDLE CAREFULLY!
Upper
Panel Retainer
Bracket
Paint edge of side panels to
match black glass.
1. Engage the River Rock bed with the two center
burner pins as shown in fig. 27. Either side of the
rocks may face outward as desired.
2. Evenly disperse the Ember Stones supplied over
the burner plate around the log parts. DO NOT
ALLOW EMBER STONES TO BLOCK THE PILOT ASSEMBLY AREA. The carry-over ports directly in front
of the pilot must remain clear for proper pilot
ignition. See figs. 29 and 65 for examples.
Figure 25. Loosen the panel retainer screws.
StarFire Glass Embers
Do not use more than the four pounds (in two, 2 lb.
bags) of glass media provided. For best results, evenly
spread the contents of the bag over the entire burner
plate and rear skirt, mounding a crown toward the
center.
Rear Glass Panel
DO NOT COVER THE AREA IMMEDIATELY IN FRONT OF
THE PILOT ASSEMBLY. The carry-over ports directly in
front of the pilot assembly must be clear to ensure proper
pilot ignition. See fig. 66 page 34.
Figure 26. Install Rear Glass Panel.
Figure 26a. Install Side Glass Panels.
Figure 27. Set River Rock assembly on pins.
19
139467_12 GF 370 DV II 12/17
Tumbled Stones
Install the stones according to the instructions supplied with that kit.
Install the Log Set
The three-piece log set includes a bag of ember
stones that simulate glowing coals when the burner
is operating.
Use workgloves and handle the individual logs
carefully, supporting each with both hands. Install
the Logset and Ember Stones as shown in figures
28-31.
Figure 30. Engage the Left Log with the rear burner
plate pin.
Figure 28. Engage the Bottom Log with the two
center pins in the burner plate.
Figure 31.
Evenly disperse the Ember Stones evenly over the
burner plate around the log parts. DO NOT ALLOW
EMBER STONES TO BLOCK THE PILOT ASSEMBLY AREA.
The carry-over ports directly in front of the pilot must
remain clear for proper pilot ignition.
Figure 29. Lean the Right Log up against the upper
right corner of the firebox and engage its toe with the
indentation in the Bottom Log.
20
Replace the Glass Frame.
Reinstall the glass frame using the 4 mm hex key
and socket head screws previously removed.
139467_12 GF 370 DV II
10. Initial System Check
The burner and fan control system consists of the
following built-in or supplied components:
1) Remote Transmitter - 3, AAA batteries preinstalled
2) Remote Receiver - 4, AA backup batteries preinstalled
3) Fan Control Module - switched
All internal connections have been made at the
factory. The remote controls are preprogramed and
the entire system tested.
NOTE: Check the build date on the shipping
crate label. If it has been more than 6 months
since the build date, be prepared to replace
the Receiver and Transmitter batteries.
Follow this procedure for the initial system check
following installation:
1. Connect the power extension cord to the interior
power cord and to a 120V electrical outlet.
2. PURGING THE GAS LINE: Open the gas supply
valve. When lighting the appliance for the first
time it will take a few moments to clear the gas
line of air. Once the purge is complete, the pilot
light will be able to ignite.
12/17
3. Set the Pilot Mode:
• CPI for continuous pilot operation or Proflame 2 Remote functionality.
• IPI for intermittent operation.
4. Once the pilot is lit, burner operation is controlled
by the rocker switch located on the front panel. See
fig. 32.
ON / OFF - use for manual control of the burner.
It remains in the ON position for use with the
Proflame 2 remote transmitter.
T-STAT - use for optional wall thermostat.
5. PILOT FLAME: The pilot flame should be steady
-not lifting or floating. The flame should be blue in
color around the pilot hood, with traces of yellow
toward the outer edges. It is important that the
pilot flame engulf the top 1/8” of the flame sensor.
The pilot flame should project out of the pilot
hood 1” from both ports extending to reach the
burner plate ports. See fig. 36. The pilot flame can
be tuned by turning the adjustment screw located
on the front of the valve. See fig. 20.
6. INSTALLER PLEASE NOTE:
CHECK FUNCTIONALITY. The burner, remote
control and fan functions have each been tested at
the factory. However, it is important to run through
each function and be sure to familiarize the
homeowner with the operation procedures. See
the Operation section on pages 24-27 for details
regarding Remote Control functions and settings.
Flame
Sensor
Ignitor
Carry-over Ports
Figure 32. Correct Pilot flame pattern.
Figure 36. Correct Pilot flame pattern.
21
139467_12 GF 370 DV II 12/17
Flame Appearance / Air Shutter
Adjustment
WARNING:
AIR SHUTTER ADJUSTMENTS SHOULD ONLY BE
PERFORMED BY A QUALIFIED, PROFESSIONAL
SERVICE TECHNICIAN.
Locate the Primary Air Shutter control under the
firebox floor above the gas valve. See fig. 37. The
shutter is set at the midpoint of its adjustment
range at the factory. This will give good results in
the majority of installation configurations, however,
you may need find it necessary to adjust it to get the
best flame picture depending upon the your specific
installation.
With the burner operating, loosen the wingnut
on the shutter stem. Push the stem back toward the
rear of the stove will decrease combustion air. Pull it
forward to increase air.
Generally, flame appearance is a matter of
individual preference, however a warm yellowish
flame is most common.

Closing the air shutter - in extreme cases may
generate very long yellow flames resulting in soot.
Sooting produces black deposits on the logs, on the
inside walls of the appliance, and potentially on
the exterior termination cap.
Sooting is caused by incomplete combustion in the
flames and lack of combustion air entering the air
shutter opening.

Opening the air shutter - will generate a flame that
is blue and transparent, or “anemic”. This flame is
generally more efficient, but not as attractive.

Allow the burner to operate at the highest setting
for 20-30 minutes before making any adjustments.
Always make adjustments in 1/8” increments and
allow the burner to settle in for 10- 15 minutes
between additional adjustments.
Primary Air Shutter
Figure 37. Air Shutter location.
22
Figure 38. Proper flame picture -Traditional Logs.
Alternate flame pictures for Wishing Rock and Starfire
Glass are illustrated in figs. 64 and 65 in the Appendix on
page 30.
Operation Notes
1. For the first several hours of operation, it is
common to detect some odor as the metal and
manufacturing materials cure under heat. This
condition is temporary and can be alleviated by
allowing plenty of fresh air to circulate through the
area.
2. Condensation may develop on the glass upon each
lighting of the appliance. This “fog” will disappear
as the glass heats.
3. Keep the controls and the area under the appliance
free of dust. Always keep the appliance area clear
and free from combustible materials, gasoline and
other flammable liquids.
4. This appliance can be operated with a continuously
burning pilot flame. Exercise caution when using
household products containing combustible
vapors.
5. CAUTION: DO NOT OPERATE THIS APPLIANCE
WITH THE GLASS REMOVED, CRACKED OR BROKEN.
REPLACEMENT OF THE GLASS SHOULD BE DONE
BY A LICENSED OR QUALIFIED SERVICE PERSON.
USE ONLY REPLACEMENT GLASS PROVIDED BY
YOUR AUTHORIZED JØTUL DEALER. NEVER USE ANY
SUBSTITUTE MATERIALS.
139467_12 GF 370 DV II
Proflame 2
Remote Control
Features Overview
The Proflame 2 Integrated Fireplace Control (IFC)
incorporates electronic remote control of the Jøtul GF
370 DV II features. It is configured to control the on/
off operation both manually and thermostatically, with
standard and “Smart” thermostat features. It will also
control flame modulation, fan power and speed, accent
lighting function and level.
The system utilizes an IPI system (Intermittent Pilot
Ignition) and may also be switched to keep the pilot lit
continuously if desired (CPI - Continuous Pilot Ignition).
Power is provided to the IFC by 120V house current and
is backed-up by a 6V battery pack (4, AAA) for operation
during a power failure.
Remote Control Transmitter
The remote transmitter has all controls available on its
face for reliable, ease of use. It gives room temperature
readout, set temperature readout, all function abilities as
well as childproof lockout and low battery indicator. Icons
appear on the screen indicating which mode of operation
you are controlling. The four button controls are easy to
learn and simple to operate. The transmitter is powered
by 3, 1.5V AAA batteries.
Remote Control Receiver
The receiver is integrated with the IFC board which is
located within the valve compartment.
Integrated Fireplace Control (IFC)
The IFC is the electrical heart of the system. It provides
power to all components and converts to 6.5v DC in
the event of power failure. The IFC sends power to the
fan system and the accent light. When no line power is
available these features will not operate, however the
battery back-up allows remote control of burner operation.
Sit 885 Modulating Valve
This valve has the ability to be stepped down in six
increments between high and low. It can be done
manually or by setting the remote control to the Smart
thermostat modulation mode. Automatic modulation
means that as the room temperature approaches the limit
set for shut down, the valve gradually decreases or “stepsdown” the fire intensity. Conversely, as room temperature
cools, the valve gradually increases flame intensity. The
overall result is more comfortable, even heating that
minimizes temperature peaks and valleys.
12/17
Pilot Assembly
The pilot contains a pilot hood, igniter, and a flame
sensor. The igniter sends a spark to the pilot hood which
lights the gas. The sensor is then engulfed by the pilot
flame, flame rectification occurs and the unit remains lit.
If rectification does not occur, the main burner will not
light, and the pilot will shut down.
WARNING:
READ AND UNDERSTAND ALL OPERATING
INSTRUCTIONS BEFORE ATTEMPTING TO OPERATE
THIS APPLIANCE. DO NOT ALLOW ANYONE TO
OPERATE THIS APPLIANCE WHO HAS NOT READ
AND UNDERSTOOD THESE INSTRUCTIONS. KEEP
THE REMOTE CONTROL TRANSMITTER WHERE
CHILDREN CANNOT REACH IT.
WARNING:
SEVERE INJURY. THIS APPLIANCE CAN BE SET TO
OPERATE THERMOSTATICALLY. BE AWARE THAT
THE FIREPLACE MAY BE VERY HOT EVEN WHEN
THE BURNER IS NOT APPARENTLY OPERATING.
KEEP CHILDREN AWAY FROM THE APPLIANCE.
WARNING:
FIRE HAZARD. CAN CAUSE SEVERE INJURY OR
DEATH. THE APPLIANCE CAN TURN ON SUDDENLY. KEEP AWAY FROM THE APPLIANCE BURNER
WHEN OPERATING THE REMOTE SYSTEM.
WARNING:
OBSERVE CAUTION NEAR THE GLASS PANEL.
THE GLASS MAY SHATTER IF STRUCK BY AN OBJECT.
ALWAYS HANDLE THE GLASS PANEL WITH CARE.
ATTENTION:
• TURN “OFF” MAIN GAS SUPPLY PRIOR TO
REMOVING OR REPLACING BATTERIES.
• IN CASE OF REMOTE CONTROL MALFUNCTION,
TURN OFF THE IFC DEVICE USING THE MAIN
“ON/OFF” SWITCH.
• FOR INSTALLATION/MAINTENANCE SWITCH
“OFF” THE IFC DEVICE BY DISCONNECTING THE
MAIN POWER SUPPLY PLUG.
23
139467_12 GF 370 DV II 12/17
Control Functions
Initializing the System
Set the stove switch to CPI mode for Proflame 2
remote control. The IPI/CPI functionality will be
controlled by the remote transmitter.
2. Install three AAA batteries into the Transmitter.
1. Press the Controls Access Door to release the magnetic
catch and swing the panel down.
Switch the Burner to OFF.
Pilot Mode
Burner Control
Set the stove burner switch to ON for Proflame 2
remote control.
OFF - Turns off both remote and manual burner
functionality. Switch to OFF when the stove will not be
used for an extended period of time.
Remote Transmitter
The Transmitter features a simple button layout and
informative display screen. See figs. 51-52.
LCD DISPLAY - graphically indicates temperature
settings and status of the Thermostat, Burner, Fan, and
Accent Lamp.
ON / OFF Key - controls Burner, Fan, and Lamp functions.
THERMOSTAT Key - Used to set either Manual or
Thermostatic Control and index through thermostatic
functions.
3. Press the black (or red) button on the left front corner
of the IFC board, next to the controls switch plate.
The board will “beep” three times and a yellow LED
indicates a 10-second synchronization time limit.
4. Within the 10-second time frame, push the ON button
on the Transmitter. The IFC will “beep” four times to
indicate that it has acknowledged the transmitter
command and sets to the particular code of that
Transmitter.
5. After initialization, the burner switch must be placed
in the ON position and Pilot Mode switch placed in CPI.
The remote can then be used to control the burner.
To return to full Manual functionality, hold the red or
black initialization button down until it “beeps” three
or four times and the yellow LED illuminates. Within
10 seconds, push the button again until it signals the
acknowledgement.
UP / DOWN Arrow Key - Selects thermostat
temperature range, fan speed, and flame height.
MODE Key - used to select the component to be
controlled: CPI/IPI, Burner, Fan, and Accent Lamp.
Blue LCD Screen
The Wall Mount Bracket can be used for convenient
Transmitter storage.
Figure 40.
Remote
transmitter
function keys.
ON/OFF Key
THERMOSTAT Key
UP/DOWN Key
MODE Key


€


‚ƒ



 ­


Figure 41. Remote transmitter display data.
24

139467_12 GF 370 DV II
12/17
Remote Transmitter Controls, cont’d.
Temperature Indication Display

With the transmitter in the OFF position, press the
Thermostat Key and the Mode Key at the same
time. The display screen will show the current room
temperature cycling between Farenheit and Celsius
indicators each time the keys are pressed simultaneously. See fig. 42.
Figure 42. Room temperature readings
Turn on the Burner

Press the ON/OFF Key on the Transmitter.
The display will show all the active icons. At the
same time, the Receiver will activate the Pilot
Ignitor. First the pilot will ignite, followed shortly
by the burner. A single”beep” from the Receiver will
confirm reception of the command.
Figure 43. Burner shut-down
Turn off the Burner

Press the ON/OFF Key. The display will show only
the room temperature and icon. At the same time,
the Receiver will deactivate the call for heat and the
burner will shut down. Fig. 43. A single”beep” from
the Receiver will confirm reception of the command.
Remote Burner Control
There are six flame levels available.

With the system ON, and the burner flame level
Figure 44. Burner OFF.
Figure 45. Flame Level 1.
Figure 46. Flame Level 5.
Figure 47. Flame Level 6.
at maximum, press the Down Arrow Key once to
reduce the flame height by one step. Each time the
Down Key is pressed, the flame will step down until
the burner is finally turned off. Fig. 44.

The Up Arrow Key will increase the flame height
each tim it is pressed. If the U Arrow Key is pressed
while the system is on but the flame is off, the
flame will come on in the High position. Figs. 45-47.
A single “beep” will confirm reception of the command.
Room Thermostat (Transmitter Operation)
The Remote Control can operate as a room themostat.
The themostat can be set to a desired temperature to
control the comfort level in a room.
Room Temperature

To activate this function, press the Thermostat Key,
(Fig. 40.) The display will indicate that the room
thermostat is “ON” and the current Set Temperature
is now displayed. Fig. 48.

To adjust the Set Temperature, press the Up or
Down Arrow Keys until the desired Set Temperature
is displayed. Fig.49.
Set Temperature
Figure 48. Thermostat ON
Figure 49.
Change Set Temperature
25
139467_12 GF 370 DV II 12/17
SMART Thermostat Function
This function adjusts the flame intensity according to
the difference in the Set Point temperature and the
actual room temperature. As the room temperature
gets closer to the Set Point, the Smart Function will
modulate flame intensity down.

To activate this function, press the Thermostat Key
until the woed “SMART” appears to the right of the
thermometer bulb icon. Fig. 50.
Figure 50. Smart Mode
Figure 51. Smart Set Temp.
Figure 52. Fan Mode
Figure 53. Fan Speed
Figure 54. Lamp Control
Figure 55.. Lamp ON

To adjust the temperature, press the Up or Down
Arrow Keys until the desired Set Temperature is
displayed. Fig. 51.
Fan Speed Control

Fan speed can be adjusted through six settings. To
activate this function, press the Mode Key (Fig. 40)
to index to the Fan Control icon. See fig. 52.

Use the Up/Down Arrow Keys to turn ON, OFF, or
adjust the fan speed. Fig. 53. A single “beep” will
confirm reception of the command.
Accent Lamp Control ( Auxiliary 120V Outlet)

The auxiliary function controls the Accent Lamp
power. Press the Mode Key to index to the AUX
icon. Figs. 54-55.

Pressing the Up Arrow Key will turn the Lamp ON.
Lamp brightness can be adjusted by turning the
dimmer knob on the stove Control Panel.

Pressing the Down Arrow Key will turn the Lamp OFF.
Child Safety Lock
This function will lockout the Transmitter to prevent
unsupervised operation.

To activate the Lock, press the Mode key and UP Key
at the same time. Fig. 56.

To de-activate the Lock, press the Mode Key and UP
Key at the same time.
Low Battery Detection
The life-span of the batteries depends on various
factors; battery quality, the frequency of ignition calls,
the frequency of changes to Set Points, etc.

When Transmitter batteries are low, the Battery
icon will be displayed before all battery power is
lost. The icon will disappear when new batteries
are installed.

When Receiver batteries are low, no “beep” will
be emitted from the Receiver when it receives an
On/Off command from the Transmitter. This is an
alert for a low battery condition in the Receiver.
When the batteries are replaced, the “beep” will
26
Figure 56. Lock ON
Figure 57. Low Battery
be emitted from the Receiver when the ON/OFF
Key is pressed. See Battery Replacement under the
Maintenance section of this manual.
Manual By-Pass of the Remote System
When battery power is low or depleted, the burner
can still be operated manually by sliding the Receiver
switch to the ON position. It will immediately ignite
in the High position.
In the event of a power failure, flame modulation,
themostatic control, fan and lamp functions will be
unavailable. It is therefore aDV IIisable to keep a supply of good quality batteries on hand.
139467_12 GF 370 DV II
12/17
Maintenance
This appliance and its venting system should be
inspected before use and at least annually by a
qualified service technician.
WARNING!
THE IGNITION SYSTEM OF THIS APPLIANCE
CARRIES LIVE VOLTAGE. ALWAYS SHUT “OFF “
THE MAIN GAS SUPPLY AND DISCONNECT THE
POWER SOURCE BEFORE PERFORMING ANY
MAINTENANCE PROCEDURE.
TURN “OFF “ THE MAIN GAS SUPPLY AND
DISCONNECT THE POWER SUPPLY TO THE
APPLIANCE BEFORE REPLACING BATTERIES.
Annual Cleaning
Vent System
The entire vent system should be inspected and
cleaned every year. If the intake and exhaust
venting is disassembled for any reason, it should
be reassembled and sealed according to the vent
manufacturer’s instructions provided at the initial
installation.
Burner and Log Set
Periodically inspect the firebox and valve
compartment to BE CERTAIN THAT THE FLOW
OF COMBUSTION AND VENTILATION AIR IS
UNOBSTRUCTED. INSPECT THE PILOT ASSEMBLY FOR
CORROSION AND REPLACE ANY AFFECTED PARTS.
NOTE: INSPECT THE GLASS SURFACE FOR SCRATCHES
AS THESE CAN WEAKEN THE PANEL TENSILE
STRENGTH. REPLACE THE PANEL IF ANY SCRATCHES
ARE FOUND. USE ONLY JØTUL CERAMIC GLASS
PANELS: 156835 SIDE AND 156833 FRONT.
Glass Panel or Gasket Replacement
1. Use the 4 mm hex key to remove the four socket screws
that attach the Glass Frame to the firebox.
Remove the lower screws first and be sure to adequately
support the frame against the firebox while you remove
the upper screws.
2. Lay the assembly upside down on a flat surface, protecting
the frame from scratches using a blanket or towel.
3. The glass panel is held in place by four retainer tabs. Use
a screwdriver to carefully pry these up off the edge of
the glass retaining walls. If the tabs break off, use the
Tinnerman clips supplied with the replacement glass kit to
secure the glass panel within the frame.
4. Remove the old gasket material.
5. Beginning at the midpoint of the upper edge, apply the
new gasket around the glass panel, with the adhesive
side inside and the thicker portion on the outside. DO
NOT STRETCH THE GASKET MATERIAL. Trim off any excess,
leaving a 1/2” overlap as shown in fig. 58.
6. Lay the glass panel within the glass frame and press the tabs
back down or press the clips in place as shown in fig. 59.
The firebox should be vacuumed at least annually
to remove any surface build up. Use a soft brush
attachment and handle the logs carefully as they are
fragile.
Glass Care
Clean the glass as necessary. Wipe the surface with
a clean, dampened, soft cloth. Follow with a dry, soft
towel. Take care not to scratch the glass surface.
WARNING: DO NOT USE ABRASIVE CLEANERS
ON THE GLASS. NEVER CLEAN THE GLASS WHEN
IT IS HOT.
Gasket Inspection
It is important that the glass gasket be inspected at
least annually. Examine the ribbon gasket for signs of
deterioration and make sure the gasket has a positive
seal. Replace the gasket if necessary.
Figure 58.
Gasket application,
PN 129124
StarFire Glass Embers
NOTE: Glass embers may discolor over time, depending upon
frequency of use. Clean the embers by washing in warm, soapy
water, and dry thoroughly before reinstallation and use. After
washing, discard any permanently hazed pieces, or replace
embers annually. Colored glass embers, not supplied by Jøtul,
maybe used, but must be at least 1/2” and similar in size and
shape.
27
139467_12 GF 370 DV II 12/17
Figure 59.
156835
Front Glass
Replacement
Kit includes
gasket and spare
retainer clips.
Initializing the Remote Control
Each time you replace the batteries, you will need to
initialize communication between the Receiver and
the Transmitter.
1. Place the slider switch in the REMOTE position.
2. Insert the end of a paper clip into the hole marked
PRG on the Receiver cover. The Receiver will “beep”
three (3) times to indicate that it is ready to synchronize with the Transmitter.
3. Install 3 AAA batteries in the Transmitter bay and
push the ON button. The Receiver will “beep” four
times to indicate the Transmitter’s command is
accepted and sets to the particular code of that
Transmitter. The system is now initialized.
Accent Lamp Replacement
Battery Replacement
Battery life depends on many variables; the quality
of the batteries, frequency of remote use, and mode
of pilot operation. Keep a supply of good quality
batteries on hand to be assured of functional
continuity in the event of a power failure.
WARNING!
ALWAYS SHUT OFF THE GAS SUPPLY AND
DISCONNECT THE POWER CORD FROM HOUSE
CURRENT BEFORE REPLACING BATTERIES.
IFC Battery Replacement
Handle the replacement bulb with gloves. Skin oils
will cause the bulb to fail prematurely.
1. Remove the glass frame. See fig. 18.
2. Remove the two retainer screws with a short
phillips screwdriver. Pull the socket out of the
housing.
3. Plug the new bulb into the socket and re-install
the assembly into the lamp housing.
4. Replace the glass frame using the 4 mm hex key
and socket head screws previously removed.
PN 222943 Bulb, 130V / 50W
A red LED on the IFC board indicates low battery
power.
1. Switch the Burner to OFF and disconnect power
to the stove.
2. Access the battery box from the left side of the
control compartment. It is directly behind the
control switch plate. See fig. 68, #27. Disengage
the box from the hook & loop tape and pull it
out of the compartment.
3. Slide the cover back, install four, 1.5v AA
batteries and replace the box, tucking the wire
leads within the compartment.
4. Reconnect power to the stove.
5. Re-initialize the Remote Control transmitter
following the instructions below.
28
Figure 60. Accent Lamp Replacement.
139467_12 GF 370 DV II
Proflame 2 IFC
Wiring Diagram
12/17
Optional Proflame 2 Stepper Regulator
Electrode
Flame Sensor
CAUTION: LABEL
ALL WIRES PRIOR
TO DISCONNECTION
WHEN SERVICING
THE CONTROLS.
WIRING ERRORS CAN
CAUSE IMPROPER
AND DANGEROUS
OPERATION. ALWAYS
VERIFY PROPER
OPERATION AFTER
SERVICING THE
APPLIANCE.
ATTENTION: AU
MOMENT DE
L’ENTRETIENDES
COMMANDES,
ÉTIQUETEZ TOUS
LES FILS AVANT LE
DÉBRANCHEMENT.
DES ERREURS
DE CÂBLAGE
PEUVENT ENTRAÎUN
FONCTIONNEMENT
INADÉQUAT ET
DANGEREUX.
CPI / IPI
Switch
SIT Proflame 885 Valve
Battery Pack
Four, 1.5v AA
Burner Switch
Main IFC Harness
Optional
Variable Lamp
SIT Proflame 2 IFC
120VAC Power
Optional
Variable Speed
Blower
Figure 61. GF 370 DV II with Proflame 2 Premium Remote Control Accessories
Figure 62. Wiring Diagram - GF 370 DV II Fan
29
139467_12 GF 370 DV II 12/17
Appendix
1. Top Plate Shims
1. Remove the Top Plate.
2. Remove the three shims highlighted in the illustration below.
3. Matte Black Stoves: Replace the Top Plate and
discard the shims.
White Enamel Stoves: Locate the three larger
shims shipped separately within the firebox
and install these in the same locations as those
previously removed.
Replace the Top Plate.
Figure 63.
2. Correct Flame Pictures
Figure 64. River Rock flame picture. KEEP EMBER
STONES OFF PILOT CARRY-OVER PORTS.
30
Figure 65. Starfire Glass flame picture.
139467_12 GF 370 DV II
12/17
3. Mobile Home Installation
The Jøtul GF 370 DV II can be installed for use in a
mobile home in the U.S. and Canada provided:
1. The stove must be secured to the floor of the
mobile home. There is a hole for this purpose,
located in the pedestal base, through which a
lag screw or other appropriate fastener should
be secured to the floor. See Fig. 1, page 3.
2. The stove is installed in accordance with Title 24
CFR, Part 3280- Manufactured Home Construction and Safety Standard, in the U.S. Comply
with CSA Z240.4, Gas Equipped Recreational
Vehicles and Mobile Housing, in Canada.
3. Always contact your local officials about installation restrictions and requirements in your
area.
THIS APPLIANCE MAY BE INSTALLED AS AN OEM
INSTALLATION IN A MANUFACTURED (MOBILE)
HOME AND MUST BE INSTALLED IN ACCORDANCE
WITH THE MANUFACTURER’S INSTRUCTIONS AND
THE MANUFACTURED HOME CONSTRUCTION
AND SAFETY STANDARD, TITLE 24 CFR, PART
3280, STANDARD FOR MANUFACTURED HOME
INSTALLATION, ANSI/NCBCS A255.1 OR STANDARD
FOR CANADA, CSA Z240.4. THIS APPLIANCE IS ONLY
FOR USE WITH THE TYPE OF GAS THAT IS INDICATED
ON THE STOVE’S RATING PLATE. THIS APPLIANCE
MAY BE INSTALLED IN AN AFTERMARKET
PERMANENTLY LOCATED, MANUFACTURED
(MOBILE) HOME, WHERE NOT PROHIBITED BY
LOCAL CODE.
CET APPAREIL PEUT ETRE INSTALLE DANS UN
MAISON PREFABRIQUEE (MOBILE) DEJA INSTALLEE
A DEMEURE SI LES REGLEMENTS LOCAUX LE
PERMETTENT.
CET APPAREIL DOIT ETRE UTILISE UNIQUEMENT
AVEC LES TYPES DE GAS INDIQUES SUR LA PLAQUE
SIGNALETIQUE. NE PAS L’UTILISER AVEC D’AUTRES
GAS SAUF SI UN KITDE CONVERSION CERTIFIE EST
INSTALLE.
31
139467_12 GF 370 DV II 12/17
lllustrated Part Breakdown
Figure 66.
Firebox Part Identification.
No.
1
2
3
4
5
6
7
8
9
10
12
13
14
15
16
17
18
19
20
32
Part Number
9911
9962
117917
117967
117968
117978
118267
120004
129118
222580
22258892
22258992
22273592
156833
222943
222974
22298092
222981
222982
Description
Bolt, Hex Cap, M6x45, DIN 933, Class 8.8, Blk
Bolt, Hex Cap M6x10 DIN 933 8.8 Ser Flange Blk
Screw, HWH SMA 8 x 1/2 SL Blk Oxide
Screw, Pan Head #7 x 3/8 PH SMA Zinc
Nut, M6 Serrated Flange plain
Screw, Button Head Socket M6X10 Blk
Spacer, .375 O.D. x 1.50
Washer,Fender M6 DIN 9021B Zinc
Gasket, Starter
Firebox Weldment, GF 370
Baffle, Firebox, GF 370, MB
Glass Frame, Side, Inner, GF 370, MB
Glass Shade, Side, GF 370, MB
Replacement Front Glass & Gasket, GF 370
Light Bulb, 130 Volt, 50 Watt
Glass, Ceramic, Light Fixture, GF 370
Restrictor Indicator Washer
Delay Door, GF 370
Restrictor Plate, GF 370
No. Part Number Description
21
22298392
Simpson DV II Starter Collar, GF 370, MB
22
22298892
Light Box, Inner
24
223202
Intake Manifold, GF 370
25
22320592
Burner Skirt, Rear, GF 370, MB
26 156834
Replacement Inner Side Glass & Gasket, GF 370
27
22324392
Panel Retainer, GF 370
28 223295
Gasket, Intake Manifold, GF 370
29 118201
Screw, Button Head Socket, M6 X 16, Blk
30 22259292
Glass Frame, Curved, GF 370, MB
31
156824
Replacement Light Socket Ass’y, GF 370
32
222977
Gasket, Light Kit
33
222993
Gasket, Relief Door, GF 370
34
225403
Inner Rod, Exhaust Restrictor
35
118090
Screw, HWH SMA 8 x 5/8 SL Zinc
36 22321992
Shroud, Rear, GF 370, MB
37
22328292
Firebox Cover, GF 370, MB
38
225402
Outer Rod, Exhaust Restrictor
39* 223224
Skamol, Rear Panel
40* 223235
Skamol, Side Panel, 2
* not illustrated
139467_12 GF 370 DV II
Figure 67.
External parts
identification
12/17
41
42
No. Part Number
1
117874
2
99115
3
10447092
10447053
4
10431992
10431953
5
10448892
10448853
6
10453692
10453653
7
118019
8
117947
9
117968
10
117976
11
9906
12
117978
13
118095
14
120004
15
222664
16
222729
17
22299592
18
222998
19
222999
20
22320792
21
156843
22
156835
23
22321692
Description
Bolt, Hex Hd M8 x 16 Ser Flange, Blk
Bolt, Hex Hd M8 x 12 Ser Flange, Blk
Top Plate, Matte Black Paint
Top Plate, White Enamel
Pedestal Base, Matte Black Paint
Pedestal Base, White Enamel
Pedestal Side, Matte Black Paint
Pedestal Side, White Enamel
Access Cover, Matte Black Paint
Access Cover, White Enamel
Bolt, Hex Hd Serr Flange M6 x 25 Blk
Washer, Flat M6 -.062 DIN 125A Plain
Nut, M6 Serrated Flange plain
Screw, Flat Head Phillips M6 X 12 M/S Blk
Bolt, Hex Cap, M6x30, DIN 933, Class 8.8, Blk
Screw, Button Head Socket M6 x 10 Blk
Screw, HWH, SMA, #8 x 1”, SL, Zinc
Washer,Fender M6 DIN 9021B Zinc
Protection Cap, M8 Hex, Black
Door Handle, Plated, GF 370
Top Grill, GF 370, MB
Bracket, Firebox Mount, GF 370
Bracket, Side Support, GF 370
Bracket, Door Catch, GF 370, Matte Black
Lower Door Hinge Asy. GF 370, MB
Replacement Outer Side Glass, GF 370
Bracket, Blower Mount, GF 370, MB
No.
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Part Number Description
223220
Plate, Centering, GF 370
223227
Blower, Axial, 40 CFM, 120 V
22558492
Hinge, Door, MB
22606992
Hinge, Door, for White Enamel stove
223236
Label, Caution,
99625
Bolt, Hex Head Serr Flange M6x16 8.8 Blk
223290
Latch, Magnetic
156837
Replacement Outer Side Glass Clip Ass’y.
22328592
Bracket, Handle, MB
10446392
Door, Matte Black Paint
10446353
Door, White Enamel
10446492
Side Plate, Left, Matte Black Paint
10446453
Side Plate, Left, White Enamel
10446592
Side Plate, Right, Matte Black Paint
10446553
Side Plate, Right, White Enamel
118055
Kepnut, M4, Ext. Tooth Lockwasher, Stl, Zinc
22383292
Rear Cover, MB
224201
Gas Line Retainer
118236
Screw, M6 x 20
22385292
Rear Seam Molding, Matte Black Paint
223852WHP Rear Seam Molding, White Paint
157765
Front Safety Barrier Screen
157766
Side Safety Barrier Screen
226313
Side Plate Mounting Bracket, Left
226314
Side Plate Mounting Bracket, Right
33
43
42
40
39
YEL
41
RED
BLK
BLU
WHT
GRN
YEL/GRN
ORG
139467_12 GF 370 DV II 12/17
Figure 68.
GF 370 DVII Spud assembly parts
identification - For stoves with serial
numbers after 10000.
PILOT MODE
OPI
IPI
ProFlame 2
Remote
BURNER
ON
T-STAT
OFF
34
139467_12 GF 370 DV II
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
Part Number
118066
223204
224785
224791
129670
156812
9962
225561
225581
118214
222292
157410
222987
220734
118023
117975
223201
221390
129130
220731
117986
223231
224132
222280
223235
117922
225562
157265
118257
120517
223201
224781
117917
117921
129154
9962
22556092
157634
225563
157493
157495
223951BKP
157492
157494
Description
Screw, #12 X 2”, HWH Type A, STL zinc
Pilot Air Deflector
Pilot Assembly, Dual Fuel Flame Hood, PSE
Spacer, PSE Pilot, .188”
Gasket, Pilot Assembly
Burner Assembly, Complete
Bolt, Hex Cap M6x10 DIN 933 8.8 Ser Flange Blk
Weldment, PF2 Spud Plate
Gasket, Spud Plate,
Screw, #8 x 1/4”, Taptite, SLHWH, SZPL
Elbow, 90 deg, Brass 3/8 NTP X 3/8” Dia Tube
Rplcmt. Motorized Valve Kit, NG
Intake Restrictor
Gasket, 2.25” OD x .125”
Fender Washer, .250” x 2.25 “
Wing Nut, M6
Handle, Primary Air, GF 370
Primary Air Shutter Asby
Orifice, #38 / NG
Orifice, #53 / LP
Screw, #8 x 3/4” SL HWH SMA Zinc
Orifice Holder, Drop In Assembly
Spacer, Orifice Holder
Gasket, Drop In Orifice Holder
Flex tube w/ connectors (3/8” OD x 48”)
Nut, Hex M4 DIN 934 Plain
Battery Heat Shield
Replacement IPI Back-up Battery Box (4 AA)
Hook & Loop Tape, 1” wide, self-adhesive
Rocker Switch, SPST, Blk, Plain
Rocker Switch, SPDT, Center OFF, Blk, Plain
Conrol Face Plate, Silkscreened, IPI Stoves
Screw, HWH SMA #8 x 1/2” SL Blk Oxide
Screw, Pan Hd M4 x 12mm, 8.8 M/S, Blk Oxide
Terminal Block, 2 Pole 77 Series
Bolt, Hex Cap M6 x 10mm DIN 933 Ser. Flng
Control Bracket
Replacement Proflame 2 Control Board
Valve Brackets, PF2
Replacement Proflame 2 Wire Harness
Replacement Multifunction Remote
Replacement Remote Wall Bracket
Power Cord, 18 AWG, Grounded - 10 ft.
Replacement Burner Control Wire Harness
12/17
Use only genuine Jøtul Replacement Parts
available from your local Authorized Jøtul
Dealer or by contacting:
Jøtul North America
55 Hutcherson Dr.
Gorham, ME 04038
207 591-6601
35
139467_12 GF 370 DV II 12/17
Jøtul GF 370 DV II Limited Warranty
This warranty policy applies to gas products
identified by Jøtul, Scan, and Atra trade names, as set
forth below.
A. LIMITED FIVE YEAR WARRANTY - Cast Iron, Steel
Doors, Surround Components, Firebox:
Jøtul North America Inc. (JØTUL) warrants, to the
original retail purchaser, that those components
of the Jøtul, Scan, or Atra Gas Stove or Fireplace
specified above will be free of defects in material
and workmanship for a period of five (5) years from
the date of purchase. This warranty is subject to the
terms, exclusions and limitations set forth in the
following text.
B. LIMITED TWO YEAR WARRANTY - Burner, Burner
Treatments, Firebox Panels:
JØTUL warrants, to the original retail purchaser,
that those components of the Jøtul, Scan, or Atra
Gas Stove or Fireplace specified above will be free of
defects in material and workmanship for a period
of two (2) years from the date of purchase. This
warranty is subject to the terms, exclusions, and
limitations set forth in the following text.
C. LIMITED TWO YEAR WARRANTY - Enamel Finish:
JØTUL warrants, to the original retail purchaser,
the enamel finish on cast iron components of the
Jøtul Stove or Fireplace Insert specified above against
peeling or fading for a period of two (2) years from the
date of purchase. This warranty is subject to the terms,
exclusions and limitations set forth below.
D. LIMITED ONE YEAR WARRANTY - Gas & Electrical
Components (controls, plumbing, valve, blower):
JØTUL warrants, to the original retail purchaser,
that those components of the Jøtul, Scan, or Atra
Gas Stove or Fireplace specified above will be free of
defects in material and workmanship for a period of
one (1) year from the date of purchase. This warranty
is subject to the terms, exclusions, and limitations
set forth in the following text.
JØTUL warrants, to the original retail purchaser,
that those components of the Jøtul, Scan, or Atra
Gas Stove or Fireplace specified above will be free of
defects in material and workmanship for a period of
one (1) year from the date of purchase. This warranty
is subject to the terms, exclusions, and limitations
set forth in the following text.
JØTUL will repair or replace (including parts & labor), at its option,
any of the above components determined by JØTUL to be covered
by this warranty. You must, at your own expense, arrange to
36
deliver or ship the component to an authorized Jøtul, Scan, or Atra
dealer and arrange for pickup or delivery of the component after
repairs have been made. If, upon inspection, JØTUL determines
that the component is covered by this warranty, the repair or
replacement will be made as set forth above. This warranty is not
transferable and is extended only to, and is solely for the benefit of,
the original retail purchaser of the Jøtul, Scan, or Atra Gas Stove or
Fireplace. This paragraph sets forth the sole remedy available under
this warranty in the event of any defect in the Jøtul, Scan, or Atra
Gas Stove or Fireplace.
The warranty period for any replaced component will be the
remaining unexpired portion of the warranty period for the original
component.
Please retain your dated sales receipt in your records as proof of
purchase.
EXCLUSIONS AND LIMITATIONS
NOTICE: This warranty is void if installation or service is performed
by someone other than an authorized installer, service agency
or gas supplier, or if installation is not in conformance with the
installation and operating instructions contained in this owner’s
manual or local and/or national fire and building regulations. A
listing of local authorized installers, service agencies and gas
suppliers can be obtained from the National Fireplace Institute at
http://www.nficertified.org/.
This warranty does not cover the following:
1) Repair or replacement of parts that are subject to normal wear
and tear during the warranty period or to parts that may require
replacement in connection with normal maintenance. These parts
include gaskets and glass (except to the extent such parts suffer
damage from thermal stress).
2) Damage due to incorrect installations not in conformance with
the installation instructions contained in this owner’s manual or
local and/or national fire and building regulations.
3) Damage due to service performed by an installer, service agency
or gas supplier, unless otherwise agreed to in writing by JØTUL.
4) Labor or other costs associated with the repair of gas controls,
plumbing, burners, log set, or sheet metal firebox beyond the warranty
period.
5) Damage caused by unauthorized modification, use or repair.
6) Damage to enameled surfaces caused by improper operation or
misuse, including use that is not in conformance with the operating
instructions contained in this owner’s manual. Such damage can
typically be identified by bubbling, cracking, or discoloration of the
enamel finish.
7) Costs incurred by travel time and/or loss of service.
8) Damage incurred while the Jøtul, Scan, or Atra Gas Stove or
Fireplace is in transit.
IN NO EVENT SHALL JØTUL, ITS PARENT COMPANY, SHAREHOLDERS,
AFFILIATES, OFFICERS, EMPLOYEES, AGENTS OR REPRESENTATIVES
BE LIABLE OR RESPONSIBLE TO YOU FOR ANY SPECIAL, INDIRECT,
INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR OTHER SIMILAR
DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOST PROFITS,
LOST SALES, INJURY TO PERSON OR PROPERTY, OR DAMAGES TO
A STRUCTURE OR ITS CONTENTS, ARISING UNDER ANY THEORY
OF LAW WHATSOEVER. ALL IMPLIED WARRANTIES, INCLUDING
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, OR OTHERWISE, ARE LIMITED IN
DURATION TO THE LENGTH OF THIS WRITTEN WARRANTY. EXCEPT
139467_12 GF 370 DV II
12/17
AS EXPRESSLY SET FORTH HEREIN, JØTUL MAKES NO ORAL,
WRITTEN OR OTHER WARRANTY WITH RESPECT TO JØTUL,
SCAN OR ATRA GAS STOVES OR FIREPLACES.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, or limitations on
the length of implied warranties. Therefore, the above
exclusions or limitations may not apply to you. This
warranty gives you specific legal rights, and you may have
other rights, which vary from state to state.
JØTUL reserves the right to discontinue, modify or change the
materials used to produce the Jøtul, Scan, or Atra Gas Stove or
Fireplace. JØTUL shall have the right to replace any defective
component with substitute components determined by JØTUL
to be of substantially equal quality and price.
The dollar value of JØTUL’s liability for breach of this
warranty shall be limited exclusively to the cost of
furnishing a replacement component. JØTUL shall not in
any event be liable for the cost of labor expended by others
in connection with any defective component. Any costs or
expenses beyond those expressly assumed by JØTUL under
the terms of this warranty shall be the sole responsibility
of the owner(s) of the Jøtul, Scan, or Atra Gas Stove or
Fireplace.
No dealer, distributor, or other person is authorized to
modify, augment, or extend this limited warranty on
behalf of JØTUL. NO MODIFICATION OR CHANGE TO
THIS WARRANTY WILL BE EFFECTIVE UNLESS IT IS MADE
IN A WRITTEN DOCUMENT MANUALLY SIGNED BY AN
AUTHORIZED OFFICER OF JØTUL.
An authorized installer may have been provided with
certain information related particularly to the Jøtul, Scan, or
Atra Gas Stove or Fireplace; however, no authorized installer
or other person who may service the appliance is an agent
of JØTUL. No inference should be made that JØTUL has
tested, certified, or otherwise pronounced any person as
qualified to install or service the appliance. JØTUL shall not
be liable or otherwise responsible for any error or omission
by a person installing or servicing a Jøtul, Scan, or Atra Gas
Stove or Fireplace.
If you believe your Jøtul, Scan, or Atra Gas Stove or
Fireplace is defective, you should contact your nearest
authorized Jøtul, Scan, or Atra dealer, who will process a
warranty claim. IN ORDER TO QUALIFY FOR WARRANTY
COVERAGE, JØTUL MUST RECEIVE NOTICE OF A POSSIBLE
DEFECT WITHIN SIXTY (60) DAYS OF THE DATE THE DEFECT
IS FIRST DISCOVERED, OR REASONABLY COULD HAVE BEEN
DISCOVERED.
This warranty is given by Jøtul North America, Inc.,
55 Hutcherson Drive, Gorham, Maine 04038 USA
37
139467_12 GF 370 DV II 12/17
Your stove has a unique serial number stamped on
the rating plate which is located in the valve
compartment. Please record the serial number in the
space below. You may also wish to attach your purchase
receipt to this page for future reference.
MODEL NAME: Jøtul GF 370 DV II Gas Stove
SERIAL NUMBER:_______________________________
PURCHASE DATE:
____________________________
AUTHORIZED DEALER:__________________________
ADDRESS ___________________________________
PHONE: ____________________________________
INSTALLER:__________________________________
FUEL TYPE:____________________________________
FUEL CONVERSION:
NO _______
YES_____
NOTES:________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
38
139467_12 GF 370 DV II
LIGHTING INSTRUCTIONS
12/17
FOR YOUR SAFETY, READ BEFORE LIGHTING.
WARNING:
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION
MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR LOSS OF LIFE.
A. This appliance is equipped with an ignition
device which automatically lights the pilot.
Do not try to light the pilot by hand.
• If your gas supplier cannot be reached, call the
fire department.
C. Use only your hand to push in or turn the
gas control knob. Never use tools. If the knob
will not push in or turn by hand, do not try
to repair it. Call a qualified technician. Force
or attempted repair may result in a fire or
explosion.
B. BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the
floor because some gas is heavier than air and
will settle to the floor.
WHAT TO DO IF YOU SMELL GAS:
• Extinguish any open flame.
• Open windows.
• Do not light any appliance.
• Do not touch any electrical switches.
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone.
D. Do not use this appliance if any part has been
under water. Immediately call a qualified service technician to inspect the appliance and to
replace any part of the control system and any
gas control which has been under water.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above.
PILOT MODE
2. Set the thermostat to the lowest setting.
IPI
CPI
3. Set the Burner switch to the “OFF” position.
4. This appliance is equipped with an ignition device
which automatically lights the pilot. Do not try to
light the pilot by hand.
Proflame 2
Remote
BURNER
T-STAT
ON
5. Wait five (5) minutes to clear out any gas. Then smell
for gas, including near the floor. If you smell gas,
M
STOP! Follow “B” in the safety information above on
this label.
If you do not smell gas, go to the next step.
OFF
PILOT MODE AND BURNER CONTROLS
6.Set the Pilot Mode switch to CPI for continuous operation. The pilot will light. Set Pilot to IPI for thermostatic operation. The pilot will light when there is a
call for heat.
7. Set the Burner switch to the “ON” or “T-STAT” position.
8. Set the thermostat to the desired setting to light
the burner. If the appliance will not operate, follow
the instructions, ”To Turn Off Gas To Appliance”, and
call your service technician or gas supplier.
PILOT LIGHT FLAME PATTERN
TO TURN OFF GAS TO THE APPLIANCE:
1. Set the thermostat to the lowest setting.
2. Set the Burner Control Switch to the
“OFF” position.
3. Turn off all electrical power to the appliance if
service is to be performed.
4. Close control access door.
39
139467_12 GF 370 DV II 12/17
December, 2017
139647_12
This appliance must be installed in conformance with local and national building regulations. Before
beginning the installation, it is important that the these instructions be carefully read and understood.
Jøtul maintains a policy of continual product development. Consequently, products may differ in
specification, color or type of accessories from those illustrated or described in various publications.
Manufactured by
Jøtul North America
55 Hutcherson Dr.
Gorham, ME 04038-2634
U.S.A.
Jøtul AS
P.O. Box 1411
N-1602 Fredrikstad
Norway
40
www.jotul.us