SUBARU
UNLOCKING
TECHNOLOGY
SUBARU MANUAL
CONTENTS
APPLICATIONS
DIAGNOSTIC SOCKETS
GENERAL OPERATION
SPECIAL FUNCTIONS
TIPS AND HINTS
REMOTE CONTROL PROGRAMMING
APPLICATIONS
SUBARU
1234
BAJA
SPORTS
ALL
BAJA
TURBO
ALL
FORESTER
X,XT,XS
ALL
IMPREZA
SEDAN
ALL
IMPREZA
SPORTS
WAGON
ALL
LEGACY
WAGON
ALL
LEGACY
SEDAN
ALL
OUTBACK
ALL
OUTBACK
SPORT
ALL
OUTBACK
WAGON
ALL
OUTBACK
SEDAN
ALL
TRIBECA
ALL
DTC
APPLICATIONS
SUBARU USA
1234
FORESTER
2.5 XT
ALL
IMPREZA
WRX—STI
ALL
LEGACY
WAGON 2.5
GT
ALL
LEGACY SEDAN 2.5 GT
ALL
OUTBACK
2.5 XT &
3.0R
ALL
TRIBECA
ALL
DTC
APPLICATIONS
SUBARU
WHAT YOU NEED TO PROGRAM….
CABLE = ADC151
CABLE = ADC117
DONGLE = A (OBD 1998 >)
DONGLE = E (OBD > 1998)
DONGLE = E (9 Pin)
CABLE = ADC117 + ADC119
CABLE = ADC110-B or
CABLE = ADC110-B + ADC119
DIAGNOSTIC SOCKETS
SUBARU
IMPREZA
LEGACY
LEGACY—9 PIN
FORESTER
JUSTY
GENERAL OPERATION
INTRODUCTION
There are two types of systems fitted to Subaru vehicles that can generally be
identified by the model year, however this is not always the case.
Detailed below is a guide to help you determine which system is fitted.
> 2000
This system can normally be identified by having a keypad in the glovebox.
These vehicles can also be fitted with a Sigma alarm that have a separate remote
control.
The tester cannot be used to program these remote controls. Programming of the
remotes can only be performed using the Sigma alarm programmer.
2000 >
On these systems the keypad is now located in the fuse box and is only required if
the alarm needs de-activating. The key is now integrated with the alarm/central
locking remote control in the head of the key.
The remote control is programmed manually (Refer to the Remote Programming
section F). Also for UK vehicles please take note of the special instructions in the
Tips & Hints section.
Notes:
1. On vehicles around 2000, both systems might have to be tried to determine the
correct system even if the system physically represents the system described
above.
2. When programming keys with tester the alarm must be disarmed.
3. Only Genuine Subaru transponders must be used when programming keys.
FUNCTIONS AVAILABLE
ECU IDENTIFICATION
PROGRAM KEYS
GENERAL OPERATION
General Subaru Immobiliser info.
Immobiliser operation
With the vehicle stopped and the ignition off, there is a red LED on the dashboard
which flashes as an anti theft deterrent with a 0.2 second on time and a 2 second off
time. This indicates the vehicle is in an immobilised state. If you insert the ignition
key and start the engine, the LED will remain off, indicating no faults are found.
If an attempt is made to start the engine with an incorrect non programmed key,
the engine will start but stop after 2 seconds and the check engine light will flashengine cannot be subsequently restarted. If the read only memory plugs (on early
vehicles) are connected, the engine control unit will show code 53- using the correct
transponder will allow the vehicle to be started and the engine warning light will remain on (because code 53 is stored) until the read memory plugs are disconnected.
The ignition key utilises a transponder chip which has no battery inside, when the
key is turned on an engine request signal is sent from the engine ECU to the immobiliser ECU. The immobiliser control unit energises the antenna and amplifier situated around the ignition key barrel. The antenna sends a frequency signal of 125
KHz to the transponder chip which replies with an ID code. This code is then sent to
the immobiliser ECU which sends it back to the engine ECU and a conformation signal, if this signal code is the same as is stored within the engine ECU then the engine function is enabled. All this process takes less than 100 milliseconds. When the
ignition is switched off, the rolling code will be updated to a random value and the
engine ECU will send this new code via it's communication line to the immobiliser
ECU. In this way, the engine control unit is ready to receive the correct code next
time the Immobiliser sends it.
If a new Engine or Immobiliser control unit is fitted or if the keys are replaced, the
system must be initialised using the tester and appropriate software. Up to four keys
may be programmed using the tester and code 53 is "incorrect transponder code detected"
Specifications
Rolling code. Input of 10 incorrect codes will cause the control unit to shut down for
10 seconds. A combination scan of all available codes will take approx 432 hours
Antenna uses inductive energy transmission (passive transponder)
Maximum code pick up distance from key approx 3cm
Response time less than 100ms
System current draw 15ma (shut down state)
30ma during code transmission
Power supply
6 - 16v d.c.
Engine control unit EGI situated lower steering column
Antenna frequency 125 KHz
Immobiliser control unit Siemens SWK4690 situated lower steering column or passenger floor.
SPECIAL FUNCTION
POST 2000 MODELS
NOTE:
1.
THE ALARM SYSTEM MUST BE DISSARMED PRIOR TO PROGRAMMING
2.
ONLY GENUINE SUBARU TRANSPONDERS MUST BE USED WHEN PROGRAMMING
KEYS.
VEHICLE SELECTION MENU
At the VEHICLE SELECTION menu select the
required vehicle and press the ENTER key.
SUBARU
PRESS ENTER KEY
- > 2000
2000 - >
TURN IGNITION ON
PRESS ENTER KEY
PLEASE WAIT
TRYING TO COMMUNICATE
SUBARU
IMMOBILISER
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
SPECIAL FUNCTIONS
DIAGNOSTIC MENU
PROGRAM KEYS
Select the vehicle model year and press the ENTER
key.
Note: On vehicles around 2000, both systems
might have to be tried to determine the correct
system.
Turn Ignition ON and press the ENTER key.
The tester will now attempt to communicate with
the ECU.
If communication is successful the system
information will be displayed as shown.
Press the ENTER key.
Select SPECIAL FUNCTIONS and press the ENTER
key.
Select PROGRAM KEYS and press the
ENTER key.
PROGRAM KEYS
PLEASE INSERT
FIRST KEY
PRESS ENTER KEY
Please insert first key to be programmed and press
the ENTER key.
SPECIAL FUNCTION
PROGRAM KEYS
PLEASE WAIT
SECURITY CODE 1 SENT
PROGRAM KEYS
PLEASE WAIT
SECURITY CODE 2 SENT
PROGRAM KEYS
PLEASE WAIT
ERASING KEYS
PROGRAM KEYS
PLEASE WAIT
STORING KEY 1
PROGRAM KEYS
Note: If no more keys are required to be
programmed press BACK. If more keys are to be
programmed press ENTER and follow the on
screen instructions.
A Maximum of 4 keys can be
programmed
WOULD YOU LIKE TO
PROGRAM KEY NO 2
OK=ENTER
CLEAR=BACK
PROGRAM KEYS
REGISTERING KEY/S
PROGRAM KEYS
KEY REGISTRATION
COMPLETE
PRESS ENTER KEY
Procedure complete
SPECIAL FUNCTION
PRE 2000 MODELS
VEHICLE SELECTION MENU
At the VEHICLE SELECTION menu select the
required vehicle and press the ENTER key.
SUBARU
PRESS ENTER KEY
Select the vehicle model year and press the ENTER
key.
- > 2000
2000 - >
TURN IGNITION ON
Turn Ignition ON and press the ENTER key.
PRESS ENTER KEY
PLEASE WAIT
TRYING TO COMMUNICATE
SUBARU
IMMOBILISER
PRESS ENTER KEY
The tester will now attempt to communicate with
the ECU.
If communication is successful the system
information will be displayed as shown.
Press the ENTER key.
DIAGNOSTIC MENU
ECU IDENTIFICATION
SPECIAL FUNCTIONS
Select SPECIAL FUNCTIONS and press the ENTER
key.
DIAGNOSTIC MENU
PROGRAM KEYS
PROGRAM KEYS
KEY PROGRAMMING
PLEASE WAIT
PRESS ENTER KEY
Select PROGRAM KEYS and press the
ENTER key.
SPECIAL FUNCTION
KEY PROGRAMMING
IGNITION OFF
WAIT 2 SECONDS
IGNITION ON
PRESS ENTER TO CONTINUE
COMPLETE
PRESS ENTER TO CONTINUE
NOTE : ONLY 1 KEY CAN BE PROGRAMMED INTO
THIS SYSTEM.
NOTE : IF MORE KEYS ARE REQUIRED CLONE THE
PROGRAMMED KEY USING THE AD90
TIPS & HINTS
GENERAL
1.
2.
3.
4.
5.
6.
7.
8.
When programming keys with tester the alarm must be disarmed.
Only Genuine Subaru transponders must be used when programming keys.
The alarm system must always be disarmed before programming.
Vehicles with no communication must have the engine cranked for a few
seconds before initialising communication.
A Maximum of 4 keys can be programmed
If the tester only powers up with the ignition on, this is not a fuse fault and is
normal for some vehicles.
On vehicles fitted with a Sigma alarm that have a separate remote control,
programming of the remotes can only be performed using the Sigma alarm
programmer.
On >2000 models only I key can be programmed into the system. If more keys
are required, the existing key must be cloned using the AD90.
Procedure to modify and program a new remote key on Subaru models:
NOTE: New keys supplied by Subaru UK are 2 button variety and are incorrect
in frequency for UK vehicles (which are 1 button). The following procedure must be
followed to modify the remote key:
1.
2.
3.
4.
5.
6.
7.
Unscrew the cross-head screw from new (2 button key)
Cut-off the right hand button (viewed from above)
Discard the circuit board
Open new remote key package (part number SACC3507)
Insert new circuit board and new 1 button cover for key
Re-fit cover
Program manually.
REMOTE CONTROL PROGRAMMING
BAJA (2003 to 2006)
FORESTER (2001 to 2004)
IMPREZA (2002 to 2004)
LEGACY/OUTBACK (1999 to 2004)
Synchronization Procedure
1.
Press remote LOCK or UNLOCK button 6 times.
2.
Synchronization should be complete, check operation
Programming
1.
2.
3.
4.
5.
6.
Press remote UNLOCK button to deactivate alarm.
Open Drivers door.
Enter vehicle and close drivers door.
Within 15 seconds turn ignition ON and back to LOCK 10 times.
NOTE : Horn will sound to indicate programming mode.
Within 40 seconds open drivers door and closed drivers door and press the lock
or unlock button on one of the remote controls.
NOTE : Horn will sound 2 times to indicate it is programmed.
Repeat for all additional remote controls up to a maximum of 4.
IMPREZA (1999 to 2001)
FORESTER (1999 to 2000)
Programming
1.
2.
3.
4.
5.
6.
7.
Open Drivers door and switch ignition ON.
Press and hold the programming button (Located under steering wheel)
After 15 seconds doors will lock and unlock 3 times.
Press the LOCK button on one of the remote controls.
After 15 seconds doors will lock and unlock 3 times.
Press the LOCK button on each of the other remotes that need to be programmed. The doors will lock and unlock once for each one programmed.
After programming release the programming button.
REMOTE CONTROL PROGRAMMING
LEGACY/OUTBACK (2003 to 2006)
FORESTER (2005 to 2006)
IMPREZA (2005 to 2006)
Programming
1.
2.
3.
4.
5.
6.
7.
Press remote UNLOCK button to deactivate alarm.
Open Drivers door.
Enter vehicle and close drivers door.
Within 15 seconds turn ignition ON and back to LOCK 10 times.
NOTE : Horn will sound to indicate programming mode.
Within 40 seconds open drivers door and closed drivers door and press the lock
or unlock button on one of the remote controls.
NOTE : Horn will sound 2 times to indicate it is programmed.
Repeat for all additional remote controls up to a maximum of 4.
Once last transmitter is programmed remove key from ignition.
NOTE : Horn will sound 3 times to indicate end of programming.
LEGACY 2004 on
1.
2.
3.
4.
5.
Remove the keyless transmitter from the ignition switch.
Remove the lower trim cover at driver’s side, then connect the registration
connectors. (1 pole white connector)
Press the door lock switch (1) located under the power window main switch to
UNLOCK. (Make sure the room light blinks and buzzer sounds, and then system
is in registration mode.)
While pressing the button of keyless transmitter to be registered twice with
door lock switch pressed to UNLOCK. (Button for LOCK, UNLOCK and TRUNK are
acceptable)
When the registration is completed normally, the door lock actuator will lock/
unlock. If the lock/unlock operation is not carried out, repeat the procedure 4).
• When pressing the keyless transmitter button, slowly press for first and sec
ond (press longer for second) to check operation of door lock actuator.
• Do not press the button of keyless transmitter more than twice.
6.
7.
Repeat the steps 4) if there is an additional keyless transmitter to be registered.
Pull out the registration connector, and install the lower trim cover at driver’s
side.
NOTE: The transmitter can be registered only when the door lock switch is
remain pushed to UNLOCK.
Continuing to press the door lock switch to UNLOCK again allows to be
registered although the door lock switch is released for once.
When adding the keyless transmitter, re-registration of keyless transmitter
which was already registered is necessary.
Advanced Diagnostics Ltd
Diagnostics House
Eastboro Fields
Hemdale
Nuneaton
CV11 6GL
T: +44(0)2476 347000
F: +44(0)2476 347100
W: www.advanced-diagnostics.co.uk
Download PDF

advertising