Installation Instructions
for Dryers
Original Instructions
Keep These Instructions for Future Reference.
CAUTION: Read the instructions before using the machine.
(If this machine changes ownership, this manual must accompany machine.)
www.speedqueen.com
Part No. D514320R3
August 2017
WARNING
IMPORTANT: Purchaser must consult the local gas
supplier for suggested instructions to be followed if
the dryer user smells gas. The gas utility instructions
plus the SAFETY and WARNING note directly above
must be posted in a prominent location near the dryer
for customer use.
WARNING
Risk of fire. Highly flammable material.
WARNING
W881
Read all instructions before using unit.
•
WARNING
•
•
FOR YOUR SAFETY, the information in this manual
must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death.
W033
WARNING
Installation of unit must be performed by a qualified installer.
Install clothes dryer according to manufacturer’s
instructions and local codes.
DO NOT install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type)
duct is installed, it must be of a specific type
identified by the appliance manufacturer as suitable for use with clothes dryers. Refer to section
on connecting exhaust system. Flexible venting
materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct
clothes dryer airflow and increase the risk of fire.
W729R1
•
•
•
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Clear the room, building or area of all occupants.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the
fire department.
Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
WARNING
To reduce the risk of severe injury or death, follow all
installation instructions. Save these instructions.
W894
WARNING
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
W053
W052
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
This product uses FreeRTOS V7.2.0 (www.freertos.org).
3
Part No. D514320R3
The following information applies to the state of Massachusetts,
USA.
•
•
•
•
This appliance can only be installed by a Massachusetts licensed plumber or gas fitter.
This appliance must be installed with a 36 inch [910 mm]
long flexible gas connector.
A “T-Handle” type gas shut-off valve must be installed in the
gas supply line to this appliance.
This appliance must not be installed in a bedroom or bathroom.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
4
Part No. D514320R3
Table of Contents
Dimensions............................................................................................. 6
Installation............................................................................................. 8
Before You Start............................................................................................. 8
Supplies..................................................................................................... 8
Parts Included............................................................................................. 8
Order of Installation Steps............................................................................8
Position and Level the Dryer............................................................................8
Connect Dryer Exhaust System...................................................................... 11
Exhaust Direction......................................................................................12
Exhaust System.........................................................................................12
Gas Dryers - Connect Gas Supply Pipe........................................................... 13
Electric Dryer Only - Connect Electrical Plug..................................................15
Earth/Ground Information.......................................................................... 15
Connecting Power Cord with Three-Wire Plug.............................................15
Connecting Power Cord with Four-Wire Plug.............................................. 17
Reverse Door, if Desired................................................................................18
Wipe Out Inside of Dryer...............................................................................20
Plug In the Dryer.......................................................................................... 20
Electric Dryer........................................................................................... 20
Gas Dryer................................................................................................. 20
Recheck Steps.............................................................................................. 21
Check Heat Source........................................................................................21
Electric Dryers.......................................................................................... 21
Gas Dryers................................................................................................21
Installer Checklist.................................................................................23
© Copyright
2017, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed
written consent of the publisher.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
5
Part No. D514320R3
Dimensions
Dimensions
Electric Models
A
B
G
I
K
J
C
E
H
D
F
A
* 40.42 in. [1027 mm]
B
* 39.61 in. [1006 mm]
C
* 15.44 in. [392 mm]
D
* 4 in. [102 mm]
E
15.4 in. [391 mm]
F
26.875 in. [683 mm]
G
* 4.5 in. [114 mm]
H
0.4 in. [10 mm]
I
8 in. [203 mm]
J
28 in. [711 mm]
K
23.5 in. [597 mm]
NOTE: Exhaust openings are 4 inch [102 mm] metal
ducting.
DRY2638N_SVG
* With leveling legs turned into base.
Gas Models
A
B
I
K
D C
E
F
H
J
L
G
© Copyright, Alliance Laundry Systems LLC -
6
M
1
DRY2639N_SVG
1. 3/8 in. NPT Gas Connection
DO NOT COPY or TRANSMIT
Part No. D514320R3
Dimensions
A
*40.42 in. [1027 mm]
B
*39.61 in. [1006 mm]
C
*15.44 in. [392 mm]
D
*2.8 in. [70 mm]
E
2.3 in. [60 mm]
F
15.4 in. [391 mm]
G
26.875 in. [683 mm]
H
4 in. [102 mm]
I
*4.5 in. [114 mm]
J
0.4 in. [10 mm]
K
8 in. [203 mm]
L
28 in. [711 mm]
M
23.5 in. [597 mm]
NOTE: Exhaust openings are 4 inch [102 mm] metal
ducting.
* With leveling legs turned into base.
NOTE: Gas models cannot be vented out left side of
cabinet because of burner housing.
IMPORTANT: The dryer should have sufficient clearance around it for needed ventilation and for the ease
of installation and servicing. For maximum drying performance, we recommend that more clearance be allowed around the dryer than the clearances that are
listed throughout this manual.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
7
Part No. D514320R3
Installation
Installation
Before You Start
•
•
•
•
Supplies
For most installations, the basic supplies you will need are:
1
2
3
Order of Installation Steps
4
1. Position and level the dryer.
2. Connect dryer to exhaust system.
3. For gas models only, connect the gas supply pipe. Check for
gas leaks.
4. For electric models only, connect the electrical cord.
5. Reverse the door, if desired.
6. Wipe out the inside of the dryer.
7. Plug in the dryer.
8. Recheck steps.
9. Start and run the dryer in a heat setting to verify dryer is heating.
8
6
7
User’s Guide
Dryer Rack Reply Card (Select Models Only)
Warranty Bond
Three screws (electric dryers only). Refer to Electric Dryer
Only - Connect Electrical Plug.
5
Position and Level the Dryer
1. Install dryer before washer. This allows room for attaching
exhaust duct.
2. Select a location with a solid floor. Dryers installed in residential garages must be elevated 18 inches [457 mm] above
the floor.
No other fuel burning appliance should be installed in the same
closet with the dryer.
DRY2586N_SVG
1.
2.
3.
4.
5.
6.
7.
8.
Wrench
1/4 inch Driver
Screwdrivers
Level
Gloves
Teflon Tape
Duct Tape
Safety Glasses
The dryer must not be installed or stored in an area where it will
be exposed to water and/or weather.
The dryer needs sufficient clearance and an adequate air supply
for proper operation and ventilation, and for easier installation
and servicing. (Minimum clearances are shown in Figure 3 ).
3. Place the dryer in position, and adjust the legs until the dryer
is level from side to side and front to back. Leveling legs can
be adjusted from inside the dryer with a 1/4 in. driver.
4. All four legs must rest firmly on the floor so the weight of the
dryer is evenly distributed. The dryer must not rock.
Figure 1
NOTE: This appliance is suitable for use in countries
having a warm, damp climate.
WARNING
Any disassembly requiring the use of tools must be
performed by a suitably qualified service person.
W299
Parts Included
An accessories bag has been shipped inside your dryer. It includes:
•
Installation Instructions
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
8
Part No. D514320R3
Installation
2
1
3
DRY2500N_SVG
1. Dryer Base
2. Level
3. Leveling Leg
Figure 2
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
9
Part No. D514320R3
Installation
Front View (Without Closet Door)
B
A
A
DRY2640N_SVG
Side View (Closet Door)
1
E
D
A
H
3
C
DRY2641N_SVG
Front View (Closet Door)
F
2 (G)
F
DRY2637N_SVG
1. Closet Door
2. Centered Air Openings (G) (2 Openings minimum)
3. Outer Wall of Enclosure
Figure 3
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
10
Part No. D514320R3
Installation
Area
Free Standing/Alcove Installation
Description
Closet Installation
A*
Dryer sides and rear clearance
0 in. [0 mm]
0 in. [0 mm]
B
Dryer top clearance
12 in. [305 mm]
12 in. [305 mm]
C
Dryer front clearance
Not Applicable
2 in. [51 mm]
D
Exhaust duct clearance to com- 2 in. [51 mm]
bustible material
2 in. [51 mm]
E
Weather hood to ground clearance
12 in. [305 mm]
12 in. [305 mm]
F
Distance from floor or ceiling
to air opening edge
Not Applicable
3 in. [76 mm]
G
Area of centered air openings
Not Applicable
in closet door. Louvered door
with equivalent air openings is
acceptable. (Minimum clearances are shown.)
40 sq. in./open [1016 sq. mm/
open]
H
For new installations, it is sug- 42 in. [1067 mm]
gested to locate top of wall vent
42 inches [1067 mm] above
floor to make venting easier to
connect.
42 in. [1067 mm]
*
Rear clearance is minimum. 2 inches [51 mm] is recommended for utility connection. 6 inches
[152 mm] is recommended when venting through rear of unit.
Table 1
IMPORTANT: In mobile home installations, gas dryers
MUST be permanently attached to the floor at the time
of installation. Order No. 526P3 Hold Down Kit (available at extra cost) for a manufactured (mobile) home installation. Follow the instructions supplied with the kit.
WARNING
To reduce the risk of fire and the accumulation of
combustion gases, DO NOT exhaust dryer air into a
window well, gas vent, chimney or enclosed, unventilated area, such as an attic, wall, ceiling, crawl
space under a building or concealed space of a
building.
Installation of unit must conform to the Manufactured Home
Construction and Safety Standards, Title 24 CF4, Part 32-80 or
Standard CAN/CSA-Z240 MH.
Connect Dryer Exhaust System
W045
WARNING
WARNING
To reduce the risk of fire and combustion gas accumulation the dryer MUST be exhausted to the outdoors.
This gas appliance contains or produces a chemical
or chemicals which can cause death or serious illness and which are known to the State of California
to cause cancer, birth defects, or other reproductive
harm. To reduce the risk from substances in the fuel
or from fuel combustion, make sure this appliance is
installed, operated, and maintained according to the
instructions in this manual.
W604
W115
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
11
Part No. D514320R3
Installation
•
WARNING
•
To reduce the risk of fire, DO NOT use plastic or thin
foil ducting to exhaust the dryer.
W354
•
•
•
WARNING
To reduce the risk of fire, the exhaust duct and
weather hood MUST be fabricated of a material that
will not support combustion. Rigid or flexible metal
pipe is recommended for a clothes dryer.
W048
•
•
•
•
Dryer exhaust duct MUST NOT terminate under mobile
home.
Exhaust duct must not be connected to any other duct, vent, or
chimney.
Dryer exhausts 220 cfm per unit (measured at back of dryer).
DO NOT install flexible duct in concealed spaces, such as a
wall or ceiling.
Static pressure in exhaust duct should not be greater than 0.6
inches water column [1.5 cm water column], measured with
manometer placed on exhaust duct 2 feet [610 mm] from dryer (check with dryer running and no load).
Exhausting dryer in hard-to-reach locations can be done by
installing 521P3 Flexible Metal Vent Kit (available as optional equipment at extra cost).
Sufficient make-up air must be supplied to replace the air exhausted by the dryer. The free area of any opening for outside
air must be at least 40 in.2 [25806 mm2] per unit.
Failure to exhaust dryer properly will void warranty.
A dryer will dissipate 60 Btu/ft2 [681,392 J/m2] of surface
area exposed to the conditioned air.
NOTE: Venting materials are not supplied with the dryer (obtain locally).
1
IMPORTANT: DO NOT block the airflow at the bottom of
the dryer’s front panel with laundry, rugs, etc. Blockage
will decrease airflow through the dryer, thus reducing
the efficiency of the dryer.
2
DRY2501N_SVG
1. Correct
2. Incorrect
Figure 4
•
•
•
•
•
•
•
•
•
DO NOT use plastic, thin foil or type B ducting. Rigid metal
duct is recommended.
Locate dryer so exhaust duct is as short as possible.
Be certain old exhaust ducts are cleaned before installing your
new dryer.
Use 4 inch [102 mm] diameter rigid or flexible metal duct.
The male end of each section of duct must point away from
the dryer.
Use as few elbows as possible.
Use of duct tape or pop-rivets on all seams and joints is recommended, if allowed by local codes. DO NOT use sheet
metal screws or fasteners on exhaust pipe joints which extend
into the duct and catch lint.
Ductwork that runs through unheated areas must be insulated
to help reduce condensation and lint build-up on pipe walls.
In mobile home installations, dryer exhaust duct must be secured to mobile home structure.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
Exhaust Direction
The dryer can be exhausted to the outdoors through the back, left,
right or bottom of the dryer. EXCEPTION: Gas dryers cannot be
vented out the left side because of the burner housing.
Dryer is shipped from factory ready for rear exhaust.
Exhausting the dryer through sides or bottom can be accomplished by installing a Directional Exhaust Kit, 528P3, available as
optional equipment at extra cost.
Exhaust System
For best drying results, recommended maximum length of exhaust system is shown in Table 2 .
To prevent backdraft when dryer is not in operation, outer end of
exhaust pipe must have a weather hood with hinged dampers (obtain locally).
NOTE: Weather hood should be installed at least 12 inches [305 mm] above the ground. Larger clearances
may be necessary for installations where heavy snowfall can occur.
12
Part No. D514320R3
Installation
Weather Hood Type
Number of 90° Elbows
Recommended
Use Only for Short Run Installations
1
1
D673I_SVG
1. 4 in. [102 mm]
1
D802I_SVG
1. 2.5 in. [64 mm]
Maximum length of 4 in. [102 mm] diameter rigid metal duct.
0
65 feet [19.8 m]
55 feet [16.8 m]
1
55 feet [16.8 m]
47 feet [14.3 m]
2
47 feet [14.3 m]
41 feet [12.5 m]
3
36 feet [11.0 m]
30 feet [9.1 m]
4
28 feet [8.5 m]
22 feet [6.7 m]
Table 2
NOTE: Deduct 6 feet [1.8 m] for each additional elbow.
WARNING
NOTE: The maximum length of a 4 in. [102 mm] diameter flexible metal duct must not exceed 7.87 ft. [2.4 m],
as required to meet UL2158, clause 7.3.2.A.
To reduce the risk of gas leaks, fire or explosion:
Gas Dryers - Connect Gas Supply Pipe
•
•
•
•
•
•
The dryer must be connected to the type of gas
as shown on nameplate located in the door recess.
Use a new flexible stainless steel connector.
Use pipe joint compound insoluble in L.P. (Liquefied Petroleum) Gas, or Teflon tape, on all pipe
threads.
Purge air and sediment from gas supply line before connecting it to the dryer. Before tightening
the connection, purge remaining air from gas line
to dryer until odor of gas is detected. This step is
required to prevent gas valve contamination.
Do not use an open flame to check for gas leaks.
Use a non-corrosive leak detection fluid.
Any disassembly requiring the use of tools must
be performed by a suitably qualified service person.
W316
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
13
Part No. D514320R3
Installation
NOTE: When connecting to a gas line, an equipment
shut-off valve in accordance with the National Fuel
Gas Code, ANSI Z223.1/NFPA 54 and the Natural
Gas and Propane Installation Code, CSA B149.1
must be installed within 6 feet [1.8 m] of the dryer.
An 1/8 in. NPT pipe plug must be installed as shown
for checking inlet pressure. Refer to Figure 5 .
1. Make certain your dryer is equipped for use with the type of
gas in your laundry room. Dryer is equipped at the factory for
Natural Gas with a 3/8 inch NPT gas connection.
NOTE: The gas service to a gas dryer must conform
with the local codes and ordinances, or in the absence of local codes and ordinances, with the latest
edition of the National Fuel Gas Code ANSI Z223.1/
NFPA 54 or the CAN/CSA-B149.1 Natural Gas and
Propane Installation Code.
1
Natural Gas, 1000 Btu/ft3 [37.3 MJ/m3], service must be supplied
at minimum 5.0 inch water column pressure to maximum 10.5
inch water column pressure.
5
For proper operation at altitudes above 3000 feet [915 m] the natural gas valve spud orifice size must be reduced to ensure complete combustion. Refer to Table 3 .
2
Natural Gas Altitude Adjustments
Altitude
feet [m]
3
4
Orifice Size
No.
inches [mm]
Part
No.
D233I_SVG
3000 [915]
43
0.0890 [2.26]
D503778
6000 [1830]
44
0.0860 [2.18]
58719
8000 [2440]
45
0.0820 [2.08]
D503779
9000 [2740]
46
0.0810 [2.06]
D503780
10,000 [3050]
47
0.0785 [1.99]
D503781
1. New Stainless Steel Flexible Connector – (Use design
CSA certified connector) Use only if allowed by local codes
2. 1/8 in. NPT Pipe Plug
3. Equipment Shut-Off Valve
4. Black Iron Pipe:
Shorter than 20 ft. [6.1 m] – Use 3/8 in. [9.5 mm] pipe.
Table 3
Longer than 20 ft. [6.1 m] – Use 1/2 in. [12.7 mm] pipe.
5. 3/8 in. NPT Gas Connection
2. Remove the shipping cap from the gas connection at the rear
of the dryer. Make sure you do not damage the pipe threads
when removing the cap.
NOTE: If gas supply connection is British Standard
Pipe Tapered thread (BSPT), order 44178804 brass
female NPT (FPT) to male BSPT gas pipe thread
adapter, available at extra cost.
3. Connect to gas supply pipe using thread sealant or Teflon
tape. Torque 90 - 175 inch-pounds [10.2 - 19.7 Nm].
NOTE: The connection of gas supply to the appliance shall be made with a flexible hose suitable for
the appliance category in accordance with national
installation regulations of the country of destination. If in doubt contact the dryer distributor or manufacturer.
Figure 5
4. Tighten all connections securely but don't overtighten to avoid
breaking or bending the gas valve bracket. Turn on gas and
check all pipe connections (internal & external) for gas leaks
with a non-corrosive leak detection fluid.
NOTE: The dryer and its appliance main gas valve must
be disconnected from the gas supply piping system
during any pressure testing of that system at test pressures in excess of 1/2 psi [3.45 kPa]. Refer to Check
Heat Source.
NOTE: DO NOT connect the dryer to L.P. Gas Service
without converting the gas valve. Install L.P. Gas Conversion Kit 649P3, available at extra cost.
L.P. (Liquefied Petroleum) Gas, 2500 Btu/ft.3 [93.1 MJ/m3], service must be supplied at 10 ± 1.5 inch water column pressure.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
14
Part No. D514320R3
Installation
For proper operation at altitudes above 3000 feet [915 m] the L.P.
gas valve spud orifice size must be reduced to ensure complete
combustion. Refer to Table 4 .
WARNING
Improper connection of the equipment earth/ground
conductor can result in a risk of electric shock.
Check with a qualified electrician or service person if
you are in doubt as to whether the dryer is properly
connected to a protective earth/ground.
L.P. Altitude Adjustments
Altitude
feet [m]
Orifice Size
No.
inches [mm]
W886
Part No.
3000 [915]
55
0.0520 [1.32]
58755
8000 [2440]
56
0.0465 [1.18]
D503786
Table 4
Electric Dryer Only - Connect Electrical
Plug
Dryer requires 120/240 Volt or 120/208 Volt, 60 Hertz, 3 or 4
wire electrical supply. Refer to serial plate for specific electrical
requirements.
IMPORTANT: Use only a new U.L. listed No. 10 (copper
wire only) three or four conductor power supply cord
kit rated 240 Volts (minimum) 30 Amperes and labeled
as suitable for use in a clothes dryer.
Do not modify the plug provided with the cord-kit - if it will not
fit the outlet, have a proper outlet installed by a qualified electrician.
The dryer has its own terminal block that must be connected to a
separate branch, 60 Hertz, single phase circuit, AC (alternating
current) circuit, fused at 30 Amperes (the circuit must be fused on
both sides of the line). Electrical service for the dryer should be
of maximum rated voltage (208 or 240 Volt, depending on heating element) listed on the serial plate. Do not connect dryer to
110, 115, or 120 Volt circuit.
Heating elements are available for field installation in dryers
which are to be connected to electrical service of different voltage than that listed on serial plate, such as 208 Volt.
NOTE: Branch circuit wire size requirements to laundry
room outlet are shown in table below.
NOTE: The wiring diagram is located in the control cabinet.
Wire Length
WARNING
To reduce the risk of fire, electric shock, serious injury or death, all wiring and grounding MUST conform with the latest edition of the National Electrical
Code, ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1, and such local regulations as
might apply. It is the customer’s responsibility to
have the wiring and fuses installed by a qualified
electrician to make sure adequate electrical power is
available to the dryer.
W521
Earth/Ground Information
This appliance must be properly connected to protective earth/
ground. In the event of malfunction or breakdown, the earth/
ground will reduce the risk of electric shock by providing a path
of least resistance for electric current.
The cord-kit must be equipped with a cord having an equipmentearth/ground conductor and an earth/ground plug. The plug must
be plugged into an appropriate outlet that is properly installed and
connected to a protective earth/ground in accordance with all local codes and ordinances.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
Wire
Less than 15 ft. [4.5 m]
Listed No. 10 AWG Copper
wire only
Longer than 15 ft. [4.5 m]
Listed No. 8 AWG Copper
wire only
Table 5
The power cord connection between wall receptacle and dryer
terminal block IS NOT supplied with dryer. Type of power cord
and gauge of wire must conform to local codes.
Connecting Power Cord with Three-Wire Plug
NOTE: Four-wire cord is required for new branch-circuit installations, mobile homes or where codes do not
permit grounding through neutral.
NOTE: The power cord is NOT supplied with the electric dryer. Type of power cord and gauge of wire must
conform to local codes and instructions. The method
of wiring the dryer is optional and subject to local code
requirements.
NOTE: Connect the dryer to the power supply with the
MAXIMUM RATED VOLTAGE listed on the serial plate.
15
Part No. D514320R3
Installation
NOTE: Use COPPER WIRE only.
Shorter than 15 ft. (4.5 m) – use 10 AWG
Longer than 15 ft. (4.5 m) – use 8 AWG
6
7
8
1
9
14
4
10
5
11
2
2
12
13
3
16
L1 L2
15
L1 L2
D816I_SVG
1. A typical 30-Amp Three-Wire Receptacle NEMA Type 10-30R
2. 120 ± 12 V.A.C.
3. 240 ± 12 V.A.C.
4. Intermediate Fuse Box (may be omitted if service entrance box is fused)
5. Wall Receptacle
6. Power Supply
7. 3-Wire Earth/Ground Neutral 120/240 Volt, 60 Hertz AC 1 Phase Service Entrance Switch Box (Refer to NOTE above)
8. 30 Ampere Fuses or Circuit Breaker
9. Neutral Wire
10. Metallic or Non-Metallic Sheathed Cable (Copper Wire Only)
11. Power Cord (Not supplied with dryer)
12. Neutral
13. Terminal Block in Dryer
14. Intermediate Shut-Off Box (may or may not be fused)
15. Direct Connection
16. Power Cord Connection
Figure 6
1. Disconnect power to dryer.
2. Remove access cover from rear of dryer.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
16
Part No. D514320R3
Installation
6. Secure the strain relief to the power cord, or wires, where they
enter the dryer cabinet.
7. Check the continuity of the earth/ground connection before
plugging the cord into an outlet. Use an acceptable indicating
device connected to the center earth/ground pin of the plug
and the green screw on the back of the cabinet.
8. Reinstall access cover and screw.
Connecting Power Cord with Four-Wire Plug
NOTE: Four-wire cord is required for new branch-circuit installations, mobile homes or where codes do not
permit grounding through neutral.
D695I_SVG
Figure 7
3. Use a strain relief and insert end of power cord through power
supply hole.
2
1
3
4
7
7
6
Figure 8
7
5
7
D696I_SVG
4. Use the three screws from the accessories bag to attach the
power cord wires to the terminal block. Refer to Figure 9 .
DRY2016N_SVG
3-Wire Connection
1.
2.
3.
4.
5.
6.
7.
1
2
Typical Four-Wire Receptacle
Power Cord – Not Supplied with Dryer
Strain Relief Nut
Strain Relief
0 V.A.C.
240 ± 12 V.A.C.
120 ± 12 V.A.C.
Figure 10
4
3
1. Disconnect power to dryer.
2. Remove access cover from rear of dryer.
DRY2508N_SVG
1.
2.
3.
4.
"L1" Terminal
Neutral Terminal
"L2" Terminal
Earth/Ground to Bulkhead
Figure 9
5. Using a screwdriver, tighten all screws firmly.
DRY2467N_SVG
IMPORTANT: Failure to tighten these screws firmly
may result in wire failure at the terminal block.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
Figure 11
17
Part No. D514320R3
Installation
3. Remove earth/ground screw from earth/ground to neutral wire
and save for use in Step 5. Earth/ground to neutral wire will
be attached to the neutral terminal in Step 6.
4-Wire Connection
8
1
7
2
1
3
6
DRY2468N_SVG
1. Earth/Ground Screw
4
5
DRY2482N_SVG
Figure 12
1.
2.
3.
4.
5.
6.
7.
8.
4. Use a strain relief and insert end of power cord through power
supply hole.
Neutral Terminal
“L2” Terminal
Black
White
Earth/Ground
Red
“L1” Terminal
Earth/Ground to Neutral Wire
Figure 14
DRY2469N_SVG
1. Strain Relief
Figure 13
5. Attach power cord earth/ground (green) wire to rear bulkhead
using earth/ground screw removed in Step 3.
6. Use the three screws from the accessories bag to attach the remaining power cord wires to the terminal block as follows:
a. Red wire to “L1” terminal.
b. Black wire to “L2” terminal.
c. White wire to Neutral terminal.
NOTE: When installing the white wire, loop the free
eyelet end of the earth/ground to neutral wire (removed in Step 3) and attach along with the white
wire to the neutral (center) terminal on the terminal
block.
7. Using a screwdriver, tighten all screws firmly.
IMPORTANT: Failure to tighten these screws firmly
may result in wire failure at the terminal block.
8. Secure the strain relief to the power cord, or wires, where they
enter the dryer cabinet.
9. Check the continuity of the earth/ground connection before
plugging the cord into an outlet. Use an acceptable indicating
device connected to the center earth/ground pin of the plug
and the green screw on the back of the cabinet.
10. Reinstall access cover and screw.
Reverse Door, if Desired
NOTE: Doors with windows cannot be reversed.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
18
Part No. D514320R3
Installation
The door on this dryer is completely reversible. To reverse door
proceed as follows:
1. Remove four hinge attaching screws.
D273P_SVG
Figure 18
DRY2052N_SVG
5. Remove door strike from door liner and reinstall on opposite
side.
Figure 15
2. Remove all nine screws.
DRY1917N_SVG
Figure 19
D272P_SVG
6. Insert liner under flange on bottom of door, then push top of
door liner into place.
Figure 16
3. Pull bottom of door liner out, then pull down, removing door
liner from door panel.
B
A
B
DRY1918N_SVG
Figure 20
A
DRY1916N_SVG
7. Reinstall nine screws removed in Step 2.
Figure 17
4. Rotate door panel 180 degrees as shown.
DRY1919N_SVG
Figure 21
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
19
Part No. D514320R3
Installation
8. Using screwdriver, remove two door plugs, and reinstall on
opposite side of door opening.
Electric Dryer
Connect the dryer to an electrical power source. Refer to Connect
Electrical Plug section for information on connecting power cord.
Connect to 30 Amp Circuit
DRY2503N_SVG
D275I_SVG2
Figure 22
9. Reinstall four hinge attaching screws, removed in Step 1.
Figure 25
Gas Dryer
Dryer requires 120 Volt, 60 Hertz electrical supply and comes
equipped with a 3-prong earth/ground plug. Refer to serial plate
for specific electrical requirements.
NOTE: The wiring diagram is located in the control cabinet.
WARNING
D606I_SVG
To reduce the risk of fire, electric shock, serious injury or death, all wiring and grounding MUST conform with the latest edition of the National Electrical
Code, ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1, and such local regulations as
might apply. It is the customer’s responsibility to
have the wiring and fuses installed by a qualified
electrician to make sure adequate electrical power is
available to the dryer.
Figure 23
Wipe Out Inside of Dryer
Before using dryer for the first time, use an all-purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside dryer drum.
W521
When plugging in the dryer:
•
•
•
•
DRY2504N_SVG
Figure 24
Plug In the Dryer
This appliance is to be supplied through a residual current device
(RCD) having a rated residual operating current not exceeding 30
mA.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
DO NOT overload circuits.
DO NOT use an extension cord.
DO NOT use an adapter.
DO NOT operate other appliances on the same circuit. Use
separately fused 15 Amp circuits.
The dryer is designed to be operated on a separate branch, polarized, three-wire, effective earth/ground, 120 Volt, 60 Hertz, AC
(alternating current) circuit protected by a 15 Ampere fuse,
equivalent fusetron or circuit breaker.
The three-prong earth/ground plug on the power cord should be
plugged directly into a polarized three-slot effective earth/ground
receptacle rated 120 Volts AC (alternating current) 15 Amps. Refer to Figure 26 to determine correct polarity of the wall receptacle.
20
Part No. D514320R3
Installation
Plug Cord Into Separately Fused 15 Amp Circuit
2
WARNING
This unit is equipped with a three-prong (earth/
ground) plug for your protection against shock hazard and should be plugged directly into a protective
earth/ ground three-prong receptacle. Do not cut or
remove the earth/ground prong from this plug.
3
1
8
6
W823
WARNING
7
4
Improper connection of the equipment earth/ground
conductor can result in a risk of electric shock.
Check with a qualified electrician or service person if
you are in doubt as to whether the dryer is properly
connected to a protective earth/ground.
5
W886
Do not modify the plug provided with the dryer – if it will not fit
the outlet, have a proper outlet installed by a qualified electrician.
DRY2022N_SVG
1.
2.
3.
4.
5.
6.
7.
8.
L1
Earth/Ground
Neutral
Round Earth/Ground Plug
Neutral Side
0 V.A.C.
120 ± 12 V.A.C.
120 ± 12 V.A.C.
NOTE: Have a qualified electrician check the polarity of
the wall receptacle. If a voltage reading is measured
other than that illustrated, the qualified electrician
should correct the problem.
Do not operate other appliances on the same circuit.
WARNING
To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to connect
the dryer to the electrical power source.
Figure 26
Earth/Ground Information
W037
This appliance must be properly connected to protective earth/
ground. In the event of malfunction or breakdown, the earth/
ground will reduce the risk of electric shock by providing a path
of least resistance for electric current.
Recheck Steps
The dryer is equipped with a cord having an equipment earth/
ground conductor and a three-prong earth/ground plug. The
three-prong earth/ground plug on the power cord should be plugged directly into a polarized three-slot effective earth/ground receptacle rated 110/120 Volts AC (alternating current) 15 Amps.
Check Heat Source
Refer to Installer Checklist on the back cover of this manual and
make sure that dryer is installed correctly.
Electric Dryers
1. Close the loading door and start the dryer in a heat setting (refer to the operation instructions).
2. After the dryer has operated for three minutes, the exhaust air
or exhaust pipe should be warm.
Gas Dryers
IMPORTANT: This operation is to be conducted by
qualified personnel only.
1. To view the burner flame, remove the lower front panel of the
dryer.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
21
Part No. D514320R3
Installation
2. Close the loading door and start the dryer in a heat setting (refer to the operation instructions). The dryer will start, the igniter will glow red and the main burner will ignite.
IMPORTANT: If all air is not purged out of gas line,
gas igniter may go off before gas is ignited. If this
happens, after approximately two minutes igniter
will again attempt gas ignition.
IMPORTANT: If igniter does not light, make sure gas
is turned on.
3. After the dryer has operated for approximately five minutes,
observe burner flame through lower front panel.
4. Adjust the air shutter to obtain a soft, uniform blue flame. (A
lazy, yellow-tipped flame indicates lack of air. A harsh, roaring, very blue flame indicates too much air.) Adjust the air
shutter as follows:
a. Loosen the air shutter lockscrew.
b. Turn the air shutter to the left to get a luminous yellowtipped flame, then turn it back slowly to the right to obtain
a steady, soft blue flame.
c. After the air shutter is adjusted for proper flame, tighten
the air shutter lockscrew securely.
5. Reinstall the lower front panel.
WARNING
To reduce the risk of serious injury or death, lower front panel must be in place during normal operation.
W158
6. After the dryer has operated for approximately three minutes,
exhaust air or exhaust pipe should be warm.
Shut-off Valve Only Applicable on Certain Models
5
1
6
4
3
2
DRY2753N_SVG
1.
2.
3.
4.
5.
6.
Air Shutter Lockscrew
Air Shutter
1/8 in. [3.1 mm] Pipe Plug (For checking manifold pressure)
Shut-off Valve Open Position
Shut-off Valve Closed Position
Shut-off Valve Handle
Figure 27
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
22
Part No. D514320R3
Installer Checklist
Installer Checklist
Fast Track for Installing the Dryer
1
Position and Level
the Dryer.
5
CHECK
Reverse Door, if Desired.
CHECK
DRY2634N_SVG
DRY2052N_SVG1
2
Connect Dryer Exhaust
System.
6
CHECK
Wipe Out Inside of
Dryer.
CHECK
DRY2501N_SVG1
3
GAS ONLY
• Connect Gas Supply Pipe.
• Check for Gas
Leaks.
DRY2504N_SVG1
7
CHECK
Plug In the Dryer.
Electric
CHECK
D275I_SVG1
Gas
D233I_SVG1
D254I_SVG
4
ELECTRIC ONLY
8
Recheck Steps.
Connect Electrical
Cord.
CHECK
CHECK
D679I_SVG1
9
Start and Run Dryer in Heat Setting to Verify Dryer is
Heating.
CHECK
Refer to the manual for more detailed information
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
23
Part No. D514320R3
Download PDF

advertising