IMPRESSA Z7 Instructions for Use - Jura

IMPRESSA Z7 Instructions for Use
KE
For your safety: read and understand manual before use.
Table of contents
Your IMPRESSA Z7
IMPORTANT SAFEGUARDS
4
Control elements
8
1 Preparing and using for the first time
10
JURA on the Internet ....................................................................................................................................10
Setting up the machine ..............................................................................................................................10
Filling the water tank ...................................................................................................................................10
Filling the bean container ............................................................................................................................11
First-time use .................................................................................................................................................11
Inserting and activating the filter..............................................................................................................12
Determining and adjusting the water hardness..................................................................................... 13
Adjusting the grinder ..................................................................................................................................15
2 Preparation
16
Ristretto, espresso and coffee ....................................................................................................................16
Preparing two specialty coffees at the touch of a button ....................................................................17
Special coffee ................................................................................................................................................17
Latte macchiato, cappuccino .....................................................................................................................17
Hot milk and milk foam ..............................................................................................................................18
Ground coffee ...............................................................................................................................................18
Permanently setting the amount of water for the cup size .................................................................19
Hot water ......................................................................................................................................................20
3 Daily operation
21
Switching on .................................................................................................................................................21
Daily maintenance .......................................................................................................................................21
Switching off ................................................................................................................................................ 22
4 Permanent settings in programming mode
23
Products ........................................................................................................................................................24
Energy-saving mode .................................................................................................................................. 27
Automatic switch-off ..................................................................................................................................28
Rinses ............................................................................................................................................................28
Rename .........................................................................................................................................................29
Logo ...............................................................................................................................................................30
Restore factory settings ..............................................................................................................................31
Viewing information and maintenance status ...................................................................................... 32
Unit for amount of water ........................................................................................................................... 32
Language ...................................................................................................................................................... 33
2
Table of contents
5
6
7
8
9
10
11
Maintenance
34
Rinsing the machine ...................................................................................................................................34
Rinsing the cappuccino frother ................................................................................................................ 35
Cleaning the cappuccino frother .............................................................................................................. 35
Dismantling and rinsing the cappuccino frother ..................................................................................36
Changing the filter ...................................................................................................................................... 37
Cleaning the machine ................................................................................................................................38
Descaling the machine ..............................................................................................................................39
Cleaning the bean container .....................................................................................................................42
Descaling the water tank ...........................................................................................................................42
Display messages
43
Troubleshooting
45
Transport and environmentally friendly disposal
47
Transport / Emptying the system............................................................................................................. 47
Disposal......................................................................................................................................................... 47
Technical data
48
Index
49
JURA contact details / Legal information
52
Symbol description
Warnings
J
J DANGER
This is the safety alert symbol. lt is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
J WARNING WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
J CAUTION
CAUTION, used with the safety alert symbol, indicates a hazardous situation
which, if not avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to personal injury.
Symbols used
T
Prompt to take action. This symbol means that you are being prompted to
perform some action.
E
Information and tips to make it even easier to use your IMPRESSA.
1 COFFEE
Display message
3
IMPORTANT SAFEGUARDS
IMPORTANT SAFEGUARDS
Follow the basic safety
precautions
When using electrical appliances, basic safety precautions shall
always be followed, to reduce the risk of fire, electric shock, and/or
injury to persons, including the following:
Z Read all instructions.
Z Do not touch hot surfaces. Use handles or knobs.
Z To protect against fire, electric shock and injury to persons, do
not immerse power cord, plugs, or body of machine in water
or other liquid.
Z Close supervision is necessary when any appliance is used by
or near children.
Z Unplug from outlet when not in use and before cleaning.
Allow to cool before putting on or taking off parts, and before
cleaning the appliance.
Z Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions, or has been damaged in any
manner. Return appliance to the nearest authorized service
facility for examination, repair or adjustment.
Z The use of an accessory attachment not recommended by the
appliance manufacturer may result in fire, electric shock, or
injury to persons.
Z Do not use outdoors.
Z Do not let the cord hang over the edge of a table or counter,
or touch hot surfaces.
Z Do not place on or near a hot gas or electric burner, or in a
heated oven.
Z Always attach plug to appliance first, then plug cord into the
wall outlet. To disconnect, turn any control to ‘OFF’ then
remove plug from wall outlet.
Z Do not use appliance for other than intended use.
Z Use extreme caution when dispensing hot steam, hot water
or hot coffee.
Z For household use only.
SAVE THESE INSTRUCTIONS.
Pass them on to any subsequent user.
4
IMPORTANT SAFEGUARDS
Intended use
The appliance is designed and intended for household use only. It
shall only be used for coffee preparation and to heat milk and water,
according to these instructions. Use for any other purpose will be
deemed improper. JURA Elektroapparate AG cannot accept any
responsibility for the consequences of improper use.
People, including children, who
Z do not have the physical, sensory or mental capabilities to use
the appliance safely or
Z are inexperienced or lack knowledge in how to use the appliance safely
must be supervised by a responsible person when using it, or must
be instructed in how to use it correctly.
Special power cord set
instructions
Z
Z
Z
Z
Z
The power cord is provided to reduce the risk resulting from
becoming entangled in or tripping over a long cord.
The cord shall be arranged so that it will not drape over the
counter top or table top where it can be pulled on by children
or tripped over.
This appliance has a 3-pin grounded plug. As a safety feature,
this plug will fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician.
Do not modify the plug in any way or attempt to defeat this
safety feature.
Do NOT use extension cords.
If the user chooses to use an extension cord,
Z the marked electrical rating of the extension cord shall be at
least as great as the electrical rating of the appliance, and
Z if the appliance is of the grounded type, the extension cord
shall be a grounding type 3-wire cord, and
Z the longer cord shall be arranged so that it will not drape over
the counter top or tabletop where it can be pulled on by children of tripped over.
J WARNING
To reduce the risk of fire or electric shock, DO NOT remove any service covers. DO NOT modify the appliance in any way that is not
described in these instructions. NO user serviceable parts included.
Repair MUST be done by authorized personnel only.
5
IMPORTANT SAFEGUARDS
In the event of signs of damage, for example if there is a smell of
burning, unplug the machine immediately from outlet and contact
JURA customer service.
J CAUTION
This appliance is for household use. Any servicing other than cleaning and user maintenance shall be performed by an authorized
service representative:
Z Do not immerse base in water or try to disassemble.
Z Do not put the appliance or any individual parts in the dishwasher.
Z Check voltage to be sure that the voltage indicated on the
name plate complies with your voltage.
Z Never use warm or hot water to fill the water container. Use
cold water only.
Z Keep your hands and the cord away from hot parts of the
appliance during operation.
There is a risk of scalds or burns on the spouts and the cappuccino
frother / nozzle.
Z Keep children away.
Z Do not touch any hot parts. Use the handles or knobs provided.
Z Ensure that the cappuccino frother / nozzle is correctly fitted
and clean. If incorrectly fitted or if they become blocked, the
cappuccino frother or its parts might come off.
NOTICE
6
Z
Z
Z
Never clean with scouring powders or hard implements.
Ensure that the ventilation slots are not covered.
Never pull out the drip tray during the brewing process. Only
pull the drip tray when the display instructs you or when the
appliance is ready for use.
IMPORTANT SAFEGUARDS
NEVER DO
(or you will void your
warranty protection):
Z
Z
Z
Z
Z
Z
Z
Never fill instant coffee, chocolate mix etc. into the bean container or ground coffee funnel (filler funnel for ground coffee).
It will damage the functioning of the brewing chamber.
Never fill sugar coated coffee beans into the bean container.
In case of doubt, call your dealer.
Never fill anything other than coffee beans into the bean container (no chocolate, no rice, no nuts, no spices, nothing other
than roasted coffee beans).
Never fill frozen beans into the bean container. If you store
beans in the freezer, let them thaw 3 to 4 hours before filling
them into the bean container.
Never fill anything but fresh, cold and clean water into the
water tank, except when decalcifying.
Never use mineral or carbonated water. You can use tap water,
bottled water, spring water and reverse osmosis water.
Never do anything with the machine which is not described in
these instructions. In case of doubt, call your dealer.
7
Control elements
Control elements
1
8
2
9
3
10
4
11
J HOT
5
J HOT
12
J HOT
6
7
Figure: Your machine may look different to the one shown.
1
2
3
4
5
6
7
8
Bean container cover
Water tank cover
Water tank
Power switch and power cord
(side view)
Height-adjustable cappuccino frother
Coffee grounds container
Drip tray
13
8
9
10
11
12
13
Grinder adjustment switch
Bean container with aroma preservation
cover
Filler funnel for ground coffee
Hot-water spout
Height- and width-adjustable coffee
spout
Cup platform
Control elements
1
4
1 Q
2 g
3 c
5
2
6
On/Off button
Rotary Switch
Maintenance button
7
3
8
9
4
5
6
7
8
9
10
11
12
z
q
p
e
m
u
i
o
10
11
12
Milk button
Latte Macchiato button
Cappuccino button
Special Coffee button
Display
Hot Water button
Ristretto button
Espresso button
Coffee button
9
1
1
Preparing and using for the first time
Preparing and using for the first time
JURA on the Internet
Visit us on the internet.
@ You can download short operating instructions for your
machine from the JURA website www.jura.com. You will also
find interesting and up-to-date information on your IMPRESSA
and on every aspect of coffee.
@ You can familiarize yourself with your IMPRESSA in a fun
way on the PC. The Knowledge Builder awaits you at
www.jura.com. The interactive assistant, LEO, will assist you
and explain the benefits of and how to use your IMPRESSA.
Setting up the machine
When setting up your IMPRESSA, please note the following:
Place the IMPRESSA on a horizontal surface that is not sensitive to water.
Choose a spot for your IMPRESSA which protects the machine
against overheating. Ensure that the ventilation slots are not
covered.
U
U
Filling the water tank
NOTICE
To enjoy the perfect cup of coffee we recommend changing the
water every day.
Milk, mineral water or other liquids can damage the water tank or
the machine.
T Only fill the water tank with fresh, cold water.
T Open the water tank cover.
T Remove the water tank and rinse it with cold water.
T Fill the water tank with fresh, cold water and reinsert the
tank.
T Close the water tank cover.
10
1
Preparing and using for the first time
Filling the bean container
The bean container has an aroma preservation cover. This will ensure
that your coffee beans retain their aroma for longer.
NOTICE
Coffee beans which have been treated with additives (e.g. sugar),
ground coffee or freeze-dried coffee will damage the grinder.
T Only use roasted, untreated coffee beans to fill the bean
container.
T Open the bean container cover and remove the aroma preservation cover.
T Remove any dirt or foreign objects from inside the bean
container.
T Fill the bean container with coffee beans, then close the
aroma preservation cover and the bean container cover.
First-time use
J WARNING
If the machine is operated with a defective power cord, there is a
danger of potentially fatal electric shock.
T Never use a machine which is damaged.
T Never use a machine which has a defective power cord.
E The water volume is given as standard in OZ. You can change
this setting to ML in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Unit for amount of
water’).
Precondition: The water tank and bean container are full.
T Insert the power plug into a power socket.
3 T Switch on the IMPRESSA using the power switch on the lefthand side of the machine.
Q T Press the On/Off button to switch the IMPRESSA on.
The Rotary Switch lights up. LANGUAGE ENGLISH
appears on the display.
E You can select another language by turning the Rotary Switch.
k T Press the Rotary Switch to confirm the language.
CONFIRMED appears briefly on the display to confirm the
setting.
PRESS RINSE, the Maintenance button c lights up.
11
1
Preparing and using for the first time
c
T Press the Maintenance button.
SYSTEM FILLS, the system fills up with water. The operation stops automatically and WELCOME TO JURA
appears on the display.
UNIT IS HEATING
PRESS RINSE, the Maintenance button c lights up.
c
Inserting and activating
the filter
T Place a receptacle under the coffee spout.
T Press the Maintenance button.
RINSING, the machine rinses. The operation stops automatically.
COFFEE READY appears on the display. Your IMPRESSA
is ready for use.
Your IMPRESSA no longer has to be descaled if you are using the
CLEARYL Blue filter cartridge.
E Perform the ‘inserting the filter’ operation without any interruptions. This will ensure that your IMPRESSA always produces
its best.
Precondition: COFFEE READY is displayed.
k T Press and hold the Rotary Switch until MAINTENANCE
appears on the display.
g T Turn the Rotary Switch until FILTER is displayed.
k T Press the Rotary Switch to enter the program item.
FILTER NO
g T Turn the Rotary Switch until FILTER YES is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED appears briefly on the display.
INSERT FILTER / PRESS BUTTON, the Maintenance button c lights up.
T Remove the filter cartridge extension from the Welcome
Pack.
T Fit the filter extension on top of a CLEARYL Blue filter cartridge.
T Remove and empty the water tank.
12
1
Preparing and using for the first time
T Open the filter holder and insert the filter cartridge into the
water tank, exerting slight pressure.
T Close the filter holder. It will click into place audibly.
E After three months, the filter will cease to work. You can check
the elapsed time by referring to the date plate on the filter
holder in the water tank.
c
T Fill the water tank with fresh, cold water and reinsert the
tank.
T Place a receptacle (at least 17 oz or 500 ml) under the cappuccino frother.
T Press the Maintenance button.
FILTER RINS.. Water flows out of the cappuccino
frother.
E You can interrupt rinsing of the filter at any time by pressing
any button. Press the Maintenance button c to continue rinsing of the filter.
E The water may be slightly discolored. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically after approximately 17 oz (500 ml). COFFEE READY appears on the
display. The filter is activated.
Determining and
adjusting the water
hardness
E If you are using the CLEARYL Blue filter cartridge and have
activated it in programming mode, you will not be able to
adjust the water hardness.
The harder the water is, the more frequently the IMPRESSA needs to
be descaled. It is therefore important to adjust the water hardness.
The water hardness can be adjusted on a continuous scale between
1 °dH and 30 °dH. It can also be deactivated, which means that the
IMPRESSA will not let you know when it has to be descaled.
13
1
Preparing and using for the first time
Level
Display German
Degree
(°dH)
Not active
–
Degrees of general
hardness
(°dGH)
Parts per
million
(ppm)
–
–
Indicator Strip
number of
‘reddish’ fields
–
Very soft water
<3
<3
< 53.4
Soft water
>4
>4
> 71
None
1
Hard water
> 8.4
> 8.4
> 150
2
Very hard water
> 14
> 14
> 250
3
Determining the water
hardness
You can find out what the water hardness is by using the Aquadur®
test strip supplied as standard.
T Hold the test strip briefly (for one second) under flowing
water. Shake off the water.
T Wait for about one minute.
T Read the degree of water hardness from the discoloration of
the Aquadur® test strip and the description on the packaging.
You can now adjust the water hardness.
Adjusting the water
hardness
Example: Proceed as follows to change the water hardness from
16°dH to 25°dH.
Precondition: COFFEE READY is displayed.
k T Press and hold the Rotary Switch until MAINTENANCE
appears on the display.
g T Turn the Rotary Switch until HARDNESS is displayed.
k T Press the Rotary Switch to enter the program item.
HARDNESS 16°dH
g T Turn the Rotary Switch until HARDNESS 25°dH is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED appears briefly on the display.
HARDNESS
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY appears on the display.
14
1
Adjusting the grinder
NOTICE
Preparing and using for the first time
You can adjust the grinder on a continuous scale to suit the degree
of roast of your coffee.
If you adjust the consistency of grind when the grinder is not operating, the grinder adjustment switch could be damaged.
T Only adjust the consistency of grind when the grinder is running.
The consistency of grind setting is correct if the coffee flows regularly from the coffee spout. In addition a fine, thick crema forms.
Example: Proceed as follows to change the consistency of grind
during the preparation of an espresso.
T Open the cover of the bean container.
T Place a cup under the coffee spout.
i T Press the Espresso button.
The grinder starts up. 1 ESPRESSO and the coffee
strength are displayed.
T Turn the grinder adjustment switch to the desired position
while the grinder is running.
The espresso is prepared and the consistency of grind is
adjusted.
T Close the cover of the bean container.
15
2 Preparation
2 Preparation
J WARNING
Hot coffee, hot steam and hot water can cause scalding. Scalding is
a serious burn.
T Use extreme care when handling hot liquid or steam.
T Allow liquid to cool down before drinking.
T In the event of scalding, rinse affected area with cold water
and seek medical attention.
T Keep children AWAY.
For a summary of the different temperatures, please refer to Chapter 4 ‘Permanent settings in programming mode – Products’.
E You can stop preparation of a specialty coffee, milk specialty
or hot water at any time. Just press any button.
E Before and during the grinding operation you can select the
coffee strength of individual products: extra-mild (ö),
mild (öö), normal (ööö), strong (öööö) or extrastrong (ööööö).
E During preparation, you can change the preset amount of
water by turning the Rotary Switch.
E The water volume is given as standard in OZ. You can change
this setting to ML in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Unit for amount of
water’).
E You can follow the current status of preparation on the
progress bar.
Ristretto, espresso
and coffee
All specialty coffees (ristretto u, espresso i and coffee o) are prepared following this model.
Example: Proceed as follows to prepare one coffee.
T Place a cup under the coffee spout.
o T Press the Coffee button.
Preparation starts. 1 COFFEE and the coffee strength is
displayed. The preset amount of water for coffee flows into
the cup.
Preparation stops automatically and ENJOY appears briefly
on the display. Then COFFEE READY is displayed.
16
2 Preparation
Preparing two specialty
coffees at the touch of a
button
To prepare two cups of coffee: Place two cups under the coffee
spout. Press the Coffee button twice o (within two seconds) to
start coffee preparation.
Special coffee
Example: Proceed as follows to prepare one special coffee.
T Place a cup under the cappuccino frother.
e T Press the Special Coffee button.
Preparation starts. SPECIAL and the coffee strength is
displayed. The preset amount of water for coffee flows into
the cup. Preparation stops automatically and ENJOY
appears briefly on the display. Then COFFEE READY is
displayed.
Latte macchiato,
cappuccino
Your IMPRESSA can prepare a latte macchiato or cappuccino at the
touch of a button. There is no need to move the glass or cup.
Example: Proceed as follows to prepare one latte macchiato.
T Attach the milk pipe to the cappuccino frother. Use the long
pipe for a milk carton/bottle and the short pipe for the milk
container.
T Insert the other end of the milk pipe into a milk carton/
bottle or connect it to a milk container.
T Place a glass under the cappuccino frother.
T Turn the setting wheel of the cappuccino frother to the milk
foam position 5.
q T Press the Latte Macchiato button.
E If an energy-saving mode is set, the machine heats up first.
Press the Latte Macchiato button once more as soon as
COFFEE READY is displayed again.
1 LATTE MAC. and the coffee strength is displayed.
1 LATTE MAC. / 1 MILK, the milk foam is prepared.
Preparation stops automatically when the preset amount of
milk is reached.
1 LATTE MAC.
17
2 Preparation
E There is a short interval while the hot milk separates from the
milk foam. This allows the typical layers of a latte macchiato
to form. You can choose the length of this interval in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Products’).
1 LATTE MAC. / COFFEE, coffee preparation starts.
The preset amount of water flows into the glass. Preparation
stops automatically and ENJOY appears briefly on the display. Then COFFEE READY is displayed.
To make sure the cappuccino frother always works properly, rinse
and clean it regularly (see Chapter 5 ‘Maintenance – Rinsing the
cappuccino frother’).
Hot milk and milk foam
Example: Proceed as follows to prepare milk foam.
T Attach the milk pipe to the cappuccino frother. Use the long
pipe for a milk carton/bottle and the short pipe for the milk
container.
T Insert the other end of the milk pipe into a milk carton/bottle or connect it to the milk container.
T Place a cup under the cappuccino frother.
T Turn the setting wheel of the cappuccino frother to the milk
foam position 5.
E If you want to heat the milk turn the setting wheel of the cappuccino frother to the milk position z.
z
T Press the Milk button.
1 MILK, the milk foam is prepared. Preparation stops automatically and COFFEE READY appears on the display.
To make sure the cappuccino frother always works properly, rinse
and clean it regularly (see Chapter 5 ‘Maintenance – Rinsing the cappuccino frother’).
Ground coffee
18
You can choose a second coffee variety, for example decaffeinated
coffee, with the filler funnel for ground coffee.
2 Preparation
E Never add more than two level measuring spoons of ground
coffee.
E Use ground coffee which is not ground too finely. Very fine
coffee can block up the system so that the coffee only comes
out in drips.
E If you did not fill the machine with a sufficient amount of
ground coffee, PRE-GROUND / NOT ENOUGH is displayed
and the IMPRESSA stops the operation.
E The desired specialty coffee must be prepared within approximately one minute after filling with the ground coffee.
Otherwise the IMPRESSA stops the operation and is once
more ready for use.
All specialty coffees with ground coffee are prepared following this
model.
Example: Proceed as follows to prepare an espresso using ground
coffee.
T Place an espresso cup under the coffee spout.
T Open the cover of the bean container.
T Open the cover of the filler funnel for ground coffee.
PRE-GROUND / FILL POWDER
T Place one level measuring spoon of ground coffee into the
filler funnel.
T Close the cover of the filler funnel for ground coffee.
PRE-GROUND / SELECT PRODUCT
i T Press the Espresso button.
Preparation will now begin. The preset amount of water for
espresso flows into the cup. Preparation stops automatically
and ENJOY appears briefly on the display. Then COFFEE
READY is displayed.
Permanently setting
the amount of water
for the cup size
It is easy to permanently set the amount of water for all specialty
coffees, milk specialties and hot water to the cup size. Adjust the
amount once as shown in the following example. Every time you
prepare a drink in the future, this amount of water will be dispensed.
Permanent setting of the amount of water to the cup size for all specialty coffees, milk specialties and hot water follows this model.
19
2 Preparation
Example: Proceed as follows to permanently set the amount of
water for one coffee.
Precondition: COFFEE READY is displayed.
T Place a cup under the coffee spout.
o T Press and hold the Coffee button.
1 COFFEE and the coffee strength is displayed.
o T Hold the Coffee button down until ENOUGH ? / PRESS
BUTTON appears.
o T Release the Coffee button.
Preparation starts and the coffee flows into the cup.
T Press any button as soon as there is sufficient coffee in the
cup.
Preparation stops. CONFIRMED and ENJOY appear
briefly on the display. The set amount of water for one coffee will be permanently stored. COFFEE READY appears
on the display.
E You can alter this setting at any time by repeating the above
procedure.
E You can also permanently set the amounts for all specialty coffees, milk specialties and hot water in programming mode in
the PRODUCTS program item.
Hot water
The following temperatures can be selected for preparing hot water:
low, normal, high.
J CAUTION
There is a danger of scalding from hot water splashes.
T Avoid direct contact with the skin.
m
T Place a cup under the hot-water spout.
T Press the Hot Water button.
HOT WATER and the temperature is displayed.
E By touching the Hot Water button several times (within
approximately 2 seconds) you can set the temperature to
your individual preference. This setting is not saved.
Hot water flows into the cup. Preparation stops automatically and COFFEE READY appears on the display.
20
3
3
Daily operation
Daily operation
Switching on
When the IMPRESSA is switched on, it automatically prompts you
to perform the rinse operation. Start the rinse operation by pressing
the Maintenance button c. In programming mode you can change
this setting so that the machine starts the switch-on rinse automatically (see Chapter 4 ‘Permanent settings in programming mode –
Rinses’).
Precondition: Your IMPRESSA is switched on at the power switch.
T Place a receptacle under the coffee spout.
Q T Press the On/Off button to switch the IMPRESSA on.
WELCOME TO JURA appears on the display.
UNIT IS HEATING
PRESS RINSE, the Maintenance button c lights up.
c
Daily maintenance
T Press the Maintenance button.
RINSING, the machine rinses.
The operation stops automatically and COFFEE READY
appears on the display.
To ensure that you get many years of reliable service out of your
IMPRESSA and to guarantee the optimum coffee quality, the
machine requires daily maintenance.
T Pull out the drip tray.
T Empty the coffee grounds container and the drip tray. Rinse
them with warm water.
T Dry the metal contacts on the back of the drip tray.
T Refit the coffee grounds container and the drip tray.
T Rinse the water tank with clean water.
T Dismantle and rinse the cappuccino frother (see Chapter 5
‘Maintenance – Dismantling and rinsing the cappuccino
frother’).
T Wipe the surface of the machine with a clean, soft, damp
cloth (e.g. microfiber cloth).
E In the interests of hygiene, we recommend changing the milk
pipe on a regular basis (approximately every 3 months).
Replacement pipes are available from specialized dealers
(JURA original accessory set for frothers).
21
3
Daily operation
Switching off
When you switch your IMPRESSA off, the spouts used to prepare a
specialty coffee are rinsed.
T Place a receptacle under the coffee spout and another under
the cappuccino frother.
Q T Press the On/Off button.
GOODBYE, the spouts used to prepare a specialty coffee or
milk are rinsed. The operation stops automatically and your
IMPRESSA is switched off.
E When the IMPRESSA is switched off with the On/Off button,
the machine consumes less than 0.01 W of standby energy.
The machine can be completely disconnected from the power
supply using the power switch.
22
4
4
Permanent settings in programming mode
Permanent settings in programming mode
J WARNING
Hot coffee, hot steam and hot water can cause scalding. Scalding is
a serious burn.
T Use extreme care when handling hot liquid or steam.
T Allow liquid to cool down before drinking.
T In the event of scalding, rinse affected area with cold water an
seek medical attention.
T Keep children AWAY.
For a summary of the different temperatures, please refer to Chapter 4 ‘Permanent settings in programming mode – Products.
You can make permanent settings in programming mode. You can
navigate through the program items and permanently save the
required settings simply by turning and pressing the Rotary Switch.
You can make the following settings with the Rotary Switch:
Program item
Sub-item
Explanation
MAINTENANCE
CAPPUCCINO CLEAN,
FILTER CHANGE (only if
T Select the desired maintenance
program.
If no action is taken in this program item,
programming mode is exited automatically after approximately five seconds.
filter is activated),
MACHINE CLEAN,
CAPPUCCINO RINSING,
MACHINE DESCALE (only
if filter is not activated),
PRODUCTS
MACHINE RINSING
PRODUCT / SELECT
PRODUCT
FILTER
YES, NO
T Indicate whether you are operating
your IMPRESSA with or without a
CLEARYL Blue filter cartridge.
HARDNESS
NOT ACTIVE,
1°dH – 30°dH
T Adjust the water hardness.
(only if filter is not
activated)
T Select your settings for specialty
coffees, milk specialties and hot water.
23
4
Permanent settings in programming mode
Program item
Sub-item
Explanation
ENERGY
SAVE NO,
SAVE LEVEL1,
SAVE LEVEL2
15 MIN, 30 MIN,
1 HRS – 15 HRS
T Select an energy-saving mode.
RINSES
START RINSE,
CAPPU. RINSE
T Change the settings for the switch-on
rinse and cappuccino rinse.
RENAME
PRODUCT NAME,
ON MESSAGE,
CLOSING
LOGO
T Change the individual texts.
PRODUCT,
ALL PROD.,
RESET ALL,
EMPTY SYSTEM
T Reset the permanently set values of all
products to the factory settings.
OFF AFTER
LOGO
RESET
T Select the logo to be displayed when
the graphic display is not being used to
display any other information.
T Keep track of all prepared products and
view the maintenance status.
INFORMATION
SETTINGS
T Set the time after which the IMPRESSA
should switch off automatically.
UNIT ML / OZ
T Select the unit for the amount of water.
LANGUAGE
T Select your language.
EXIT
T Exit programming mode.
Products
In the program item PRODUCTS you can make individual
settings for all specialty coffees, milk specialties and hot water.
J WARNING
24
Hot coffee, hot steam and hot water can cause scalding. Scalding is
a serious burn.
T Use extreme care when handling hot liquid or steam.
T Allow liquid to cool down before drinking.
T In the event of scalding, rinse affected area with cold water an
seek medical attention.
T Keep children AWAY.
4
Permanent settings in programming mode
The following permanent settings can be made:
Product
Temperature
Coffee strength
1 ristretto,
1 espresso,
1 coffee,
1 special
coffee
LOW
approx. 183 °F (84 °C)
NORMAL approx. 188 °F (87 °C)
HIGH
approx. 197 °F (92 °C)
XMILD ö
Amount of water:
MILD öö
0.5 OZ – 8.0 OZ
NORMAL ööö
(25 ml – 240 ml)
STRONG öööö
XSTRONG
ööööö
2 ristretti,
2 espressi,
2 coffees
LOW
approx. 183 °F (84 °C)
NORMAL approx. 188 °F (87 °C)
HIGH
approx. 197 °F (92 °C)
–
Latte
macchiato,
cappuccino
LOW
approx. 183 °F (84 °C)
NORMAL approx. 188 °F (87 °C)
HIGH
approx. 197 °F (92 °C)
XMILD ö
MILD öö
NORMAL ööö
STRONG öööö
XSTRONG
ööööö
Amount of milk:
3 SEC – 120 SEC
Interval:
0 SEC – 60 SEC
Amount of water:
0.5 OZ – 8.0 OZ
(25 ml – 240 ml)
–
3 SEC – 120 SEC
0.5 OZ – 15.0 OZ
Milk
Hot water
–
max. 149 °F (65 °C)
LOW
> 149 °F (> 65 °C)
NORMAL > 167 °F (> 75 °C)
HIGH
approx. 203 °F (95 °C)
Amount
Amount of water:
0.5 OZ – 8.0 OZ
(25 ml – 240 ml)
(per cup)
–
(25 ml – 450 ml)
Permanent settings in programming mode always follow the same
model.
Example: Proceed as follows to change the amount of milk for a
latte macchiato from 16 SEC to 20 SEC, the interval from
30 SEC to 20 SEC and the amount of water from 1.5 OZ
(45 ml) to 1.0 OZ (40 ml).
Precondition: COFFEE READY is displayed.
k T Press and hold the Rotary Switch until MAINTENANCE
appears.
g T Turn the Rotary Switch until PRODUCTS is displayed.
k T Press the Rotary Switch to enter the program item.
PRODUCT / SELECT PRODUCT
25
4
Permanent settings in programming mode
E Next select the button of the product for which you would like
to make settings. No product is prepared at this point.
E To change the setting for a double product, press the corresponding button twice within two seconds.
q
k
g
k
g
k
g
k
g
k
g
k
g
k
g
26
T Press the Latte Macchiato button.
1 LATTE MAC. / COFFEE 1.5 OZ (45 ml)
T Press the Rotary Switch to enter the program item.
1 LATTE MAC. / COFFEE 1.5 OZ (45 ml)
T Turn the Rotary Switch until 1 LATTE MAC. / COFFEE
1.0 OZ (40 ml) is displayed.
T Press the Rotary Switch to confirm the setting.
CONFIRMED appears briefly on the display.
1 LATTE MAC. / COFFEE 1.0 OZ (40 ml)
T Turn the Rotary Switch until 1 LATTE MAC. / MILK
16 SEC is displayed.
T Press the Rotary Switch to enter the program item.
1 LATTE MAC. / MILK 16 SEC
T Turn the Rotary Switch until 1 LATTE MAC. / MILK
20 SEC is displayed.
T Press the Rotary Switch to confirm the setting.
CONFIRMED appears briefly on the display.
1 LATTE MAC. / MILK 20 SEC
T Turn the Rotary Switch until 1 LATTE MAC. / PAUSE
30 SEC is displayed.
T Press the Rotary Switch to enter the program item.
1 LATTE MAC. / PAUSE 30 SEC
T Turn the Rotary Switch until 1 LATTE MAC. / PAUSE
20 SEC is displayed.
T Press the Rotary Switch to confirm the setting.
CONFIRMED appears briefly on the display.
1 LATTE MAC. / PAUSE 20 SEC
T Turn the Rotary Switch until 1 LATTE MAC. / EXIT is
displayed.
T Press the Rotary Switch to exit the program item.
PRODUCT / SELECT PRODUCT
T Turn the Rotary Switch until PRODUCT / EXIT is displayed.
4
Permanent settings in programming mode
k T Press the Rotary Switch to exit the program item.
PRODUCTS
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Energy-saving mode
In the program item ENERGY you can permanently set an energysaving mode (Energy Save Mode, E.S.M.©):
U
U
U
ENERGY SAVE NO
U Your IMPRESSA is constantly ready for use.
U All coffee and milk products as well as hot water can be prepared without having to wait.
ENERGY SAVE LEVEL1 (Energy saving of up to 30%)
U Your IMPRESSA is only constantly ready for use for coffee
products and hot water.
U The machine must heat up before milk preparation.
ENERGY SAVE LEVEL2 (Energy saving of up to 40%)
U Approximately five minutes after the last preparation your
IMPRESSA switches to the energy-saving temperature and is
not ready for use.
U The machine must heat up before the preparation of coffee,
hot water or milk.
Example: Proceed as follows to change the energy-saving mode
from ENERGY SAVE NO to ENERGY SAVE LEVEL1.
Precondition: COFFEE READY is displayed.
k T Press and hold the Rotary Switch until MAINTENANCE
appears.
g T Turn the Rotary Switch until ENERGY is displayed.
k T Press the Rotary Switch to enter the program item.
ENERGY SAVE NO
g T Turn the Rotary Switch until ENERGY SAVE LEVEL1 is
displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED appears briefly on the display.
ENERGY
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
27
4
Permanent settings in programming mode
Automatic switch-off
By instructing your IMPRESSA to automatically switch itself off, you
can cut down your energy consumption. If this function is activated,
your IMPRESSA switches off automatically after the preset time following the last action on the machine.
You can set the automatic switch-off to 15 minutes, 30 minutes or
1 – 15 hours.
Example: Proceed as follows to change the automatic switch-off
from 1 HRS to 15 MIN.
Precondition: COFFEE READY is displayed.
k T Press and hold the Rotary Switch until MAINTENANCE
appears.
g T Turn the Rotary Switch until OFF AFTER 1 HRS is displayed.
k T Press the Rotary Switch to enter the program item.
OFF AFTER 1 HRS
g T Turn the Rotary Switch until OFF AFTER 15 MIN is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED appears briefly on the display.
OFF AFTER 15 MIN
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Rinses
In the program item RINSES you can make the following settings:
U
START RINSE MANUAL
U
START RINSE AUTO
U
U The switch-on rinse must be started manually.
U The switch-on rinse is started automatically.
CAPPU. RINSE AFTER 10 MIN
U You are prompted to perform a cappuccino rinse 10 minutes
after preparation of a milk product.
U
CAPPU. RINSE NOW
U You are prompted to perform a cappuccino rinse immediately after preparation of a milk product.
28
4
Permanent settings in programming mode
Example: Proceed as follows to make the machine prompt you to
perform the cappuccino rinse immediately after preparing a milk
product.
Precondition: COFFEE READY is displayed.
k T Press and hold the Rotary Switch until MAINTENANCE
appears.
g T Turn the Rotary Switch until RINSES is displayed.
k T Press the Rotary Switch to enter the program item.
START RINSE MANUAL
g T Turn the Rotary Switch until CAPPU. RINSE AFTER
10 MIN is displayed.
k T Press the Rotary Switch to enter the program item.
CAPPU. RINSE AFTER 10 MIN
g T Turn the Rotary Switch until CAPPU. RINSE NOW is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED appears briefly on the display.
CAPPU. RINSE NOW
g T Turn the Rotary Switch until RINSES / EXIT is displayed.
k T Press the Rotary Switch.
RINSES
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Rename
You can change all product names, the welcome text and the closing
text.
Example: Proceed as follows to change the product name from
1 COFFEE to MY COFFEE.
Precondition: COFFEE READY is displayed.
k T Press and hold the Rotary Switch until MAINTENANCE
appears.
g T Turn the Rotary Switch until RENAME is displayed.
k T Press the Rotary Switch to enter the program item.
RENAME / PRODUCT NAME
E By turning the Rotary Switch you can select the welcome and
closing texts.
29
4
Permanent settings in programming mode
k T Press the Rotary Switch to enter the program item.
PRODUCT NAME / CHANGE
k T Press the Rotary Switch.
PRODUCT NAME / SELECT PRODUCT
E Next select the button of the product you want to rename. No
product is prepared at this point.
o T Press the Coffee button.
1 COFFEE is briefly displayed.
_ / ABCDEFG...w
g T Turn the Rotary Switch to select the required character.
k T Press the Rotary Switch to confirm the character.
MY COFFEE / ABCDEFG...w
E To delete the last character entered, select the y symbol at the
end of the alphabet and press the Rotary Switch.
T Select the w symbol at the end of the alphabet and press the
Rotary Switch to confirm the entry.
CONFIRMED appears briefly on the display.
RENAME
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Logo
You can choose which logo is displayed when the display is not
being used to display any other information. The available logos
include:
JURA logo
Animated coffee cup
No logo (NOT ACTIVE)
U
U
U
Example: Proceed as follows to display the JURA logo.
Precondition: COFFEE READY is displayed.
k T Press and hold the Rotary Switch until MAINTENANCE
appears.
g T Turn the Rotary Switch until LOGO is displayed.
k T Press the Rotary Switch to enter the program item.
LOGO
30
4
Permanent settings in programming mode
g T Turn the Rotary Switch until LOGO / JURA is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED appears briefly on the display.
LOGO / JURA
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY / JURA
Restore factory settings
In the program item RESET you can reset various settings to their
factory settings:
U
PRODUCT
U The settings (amount of water, aroma, temperature etc.) for
any product can be reset individually to the factory settings.
The corresponding double product is reset to the factory
settings at the same time.
U
ALL PROD.
U The settings (amount of water, aroma, temperature etc.) for
all products are reset to the factory settings.
U
RESET ALL
U All customer settings are reset to the factory settings. Your
IMPRESSA then switches off.
Example: Proceed as follows to reset the values for ‘Espresso’ to the
factory settings.
Precondition: COFFEE READY is displayed.
k T Press and hold the Rotary Switch until MAINTENANCE
appears.
g T Turn the Rotary Switch until RESET is displayed.
k T Press the Rotary Switch to enter the program item.
RESET / PRODUCT
k T Press the Rotary Switch to enter the program item.
RESET / SELECT PRODUCT
i T Press the Espresso button.
CONFIRMED appears briefly on the display and the settings for ‘Espresso’ are reset to the factory settings.
RESET / PRODUCT
g T Turn the Rotary Switch until RESET / EXIT is displayed.
31
4
Permanent settings in programming mode
k T Press the Rotary Switch to exit the program item.
RESET
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Viewing information and
maintenance status
In the program item INFORMATION you can view the following
information:
Number of prepared specialty coffees, milk specialties and hot
water
Maintenance status and number of maintenance programs
performed (cleaning, descaling, changing the filter)
Number of cappuccino frother cleaning operations performed
Software version
U
U
U
U
Precondition: COFFEE READY is displayed.
k T Press and hold the Rotary Switch until MAINTENANCE
appears.
g T Turn the Rotary Switch until INFORMATION is displayed.
k T Press the Rotary Switch to enter the program item.
TOTAL, the total number of prepared specialty coffees and
milk specialties is displayed.
g T Turn the Rotary Switch to view additional information.
E The maintenance status can also be displayed in addition to
the number of performed maintenance programs. The bar
shows the current maintenance status. When the bar is completely filled, your IMPRESSA will request the respective maintenance program.
k T Press the Rotary Switch to exit the program item.
INFORMATION
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Unit for amount of water
The water volume is given as standard in OZ. You can change this
setting to ML in programming mode.
Example: Proceed as follows to change the unit for the amount of
water from OZ to ML.
32
4
Permanent settings in programming mode
Precondition: COFFEE READY is displayed.
k T Press and hold the Rotary Switch until MAINTENANCE
appears.
g T Turn the Rotary Switch until SETTINGS / UNIT OZ is
displayed.
k T Press the Rotary Switch to enter the program item.
SETTINGS / UNIT OZ
g T Turn the Rotary Switch until UNIT ML is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED appears briefly on the display.
SETTINGS / UNIT ML
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Language
In this program item you can set the language used by your
IMPRESSA.
Example: Proceed as follows to change the language from
ENGLISH to DEUTSCH.
Precondition: COFFEE READY is displayed.
k T Press and hold the Rotary Switch until MAINTENANCE
appears.
g T Turn the Rotary Switch until LANGUAGE ENGLISH is
displayed.
k T Press the Rotary Switch to enter the program item.
LANGUAGE ENGLISH
g T Turn the Rotary Switch until SPRACHE DEUTSCH is displayed.
k T Press the Rotary Switch to confirm the setting.
GESPEICHERT appears briefly on the display.
SPRACHE DEUTSCH
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
BITTE WÄHLEN
33
5
5
Maintenance
Maintenance
J WARNING
Use of maintenance products that are harmful to health and discharge of liquids during maintenance program. Harmful if swallowed. Irritating to eyes and skin.
T Keep children AWAY.
T Keep children away from the machine while it is performing a
maintenance program.
T Avoid contact with skin and eyes.
T Avoid generation of dust. Do not inhale dust.
T When using do not eat or drink.
T Keep maintenance products away from food, drink and animal food.
T Keep container tightly closed and dry. Keep in a cool place.
Your IMPRESSA has the following integrated maintenance programs:
Cleaning the cappuccino frother
Rinsing the cappuccino frother
Changing the filter
Cleaning the machine
Rinsing the machine
Descaling the machine
U
U
U
U
U
U
E Clean or descale the machine or change the filter when the
display prompts you to do so.
Rinsing the machine
You can initiate the rinse operation manually at any time.
Precondition: COFFEE READY is displayed.
T Place a receptacle under the coffee spout.
k T Press and hold the Rotary Switch until MAINTENANCE
appears.
k T Press the Rotary Switch to enter the program item.
CAPPUCCINO CLEAN
g T Turn the Rotary Switch until MACHINE RINSING is displayed.
34
5
Maintenance
k T Press the Rotary Switch to initiate the rinse operation.
RINSING
Rinsing stops automatically and COFFEE READY appears
on the display.
Rinsing the cappuccino
frother
After each milk preparation, the IMPRESSA prompts you to run a
cappuccino rinse.
Precondition: COFFEE READY / CAPPU RINSE is displayed
and the Maintenance button c lights up.
T Place a receptacle under the cappuccino frother.
c T Press the Maintenance button.
CAPPUCCINO RINSING, the cappuccino frother is
rinsed.
COFFEE READY
Cleaning the cappuccino
frother
To ensure that the cappuccino frother always works properly, you
should clean it daily when you have been preparing milk. Your
IMPRESSA will not prompt you to clean the cappuccino frother.
J WARNING
Non-recommended cleaning agents will not optimally remove milk
residues. This may cause the cappuccino frother to become blocked
and fly off the machine. Discharge of hot steam.
T Use only original JURA milk system cleaner.
J WARNING
Harmful and irritating cleaning agent. Harmful if swallowed. Irritating to eyes and skin.
T Keep children AWAY.
T Avoid contact with skin and eyes.
T After contact with skin, wash immediately with plenty of
water. In case of skin irritation, seek medical advice.
T After eye contact, immediately flush eyes with plenty of water
and seek medical advice.
T If swallowed, rinse mouth immediately and drink large quantities of water. Do not induce vomiting. Seek medical advice
immediately and show label.
35
5
Maintenance
E JURA milk system cleaner is available from specialized dealers.
Precondition: COFFEE READY is displayed.
k T Press and hold the Rotary Switch until MAINTENANCE
appears.
k T Press the Rotary Switch to enter the program item.
CAPPUCCINO CLEAN
k T Press the Rotary Switch.
c
c
Dismantling and rinsing
the cappuccino frother
CLEANER FOR CAPPUCCINO / PRESS BUTTON
T Pour 8.5 oz (250 ml) of fresh water into a receptacle and add
one capful of milk system cleaner.
T Immerse the milk pipe in the receptacle.
T Turn the setting wheel of the cappuccino frother to the milk
foam 5 or milk z position.
T Place another receptacle under the cappuccino frother.
T Press the Maintenance button.
CAPPUCCINO CLEANING, the cappuccino frother and
the pipe are cleaned.
WATER FOR CAPPUCCINO / PRESS BUTTON
T Rinse the receptacle thoroughly, fill it with 8.5 oz (250 ml) of
fresh water and immerse the milk pipe in the water.
T Empty the other receptacle and place it under the cappuccino frother again.
T Press the Maintenance button.
CAPPUCCINO CLEANING, the cappuccino frother and
the pipe are rinsed with fresh water.
COFFEE READY appears on the display.
T Carefully pull the cappuccino frother down and off.
T Dismantle the frother completely.
T Rinse all frother parts thoroughly under running water.
T Reassemble the cappuccino frother.
E Ensure that all individual parts are correctly and firmly connected to ensure correct operation of the cappuccino frother.
T Firmly attach it to the connector.
36
5
Changing the filter
Maintenance
E After 2000 oz (60 liters) of water have flowed through, the filter will cease to work. Your IMPRESSA will automatically
prompt you to change the filter.
E After three months, the filter will cease to work. You can check
the elapsed time by referring to the date plate on the filter
holder in the water tank.
E If the CLEARYL Blue filter cartridge is not activated in programming mode, you will not be prompted to change the filter.
Precondition: COFFEE READY / FILTER CHANGE is displayed and the Maintenance button c lights up.
c T Press the Maintenance button.
CHANGE TIME 20 MIN / START YES
E If you do not want to start changing the filter just yet, turn the
Rotary Switch until CHANGE / START NO is displayed. Press
the Rotary Switch to exit the maintenance program. The
prompt to change the filter remains active.
c
c
T Press the Maintenance button.
CHANGE FILTER / PRESS BUTTON
T Remove and empty the water tank.
T Open the filter holder and remove the old CLEARYL Blue filter cartridge and extension piece.
T Fit the filter extension on top of a new filter cartridge.
T Insert the filter cartridge into the water tank, exerting slight
pressure.
T Close the filter holder. It will click into place audibly.
T Fill the water tank with fresh, cold water and reinsert the
tank.
T Place a receptacle (at least 17 oz or 500 ml) under the cappuccino frother.
T Turn the setting wheel of the cappuccino frother to the
steam position n.
T Press the Maintenance button.
FILTER RINS., water flows out of the frother.
37
5
Maintenance
E You can interrupt rinsing of the filter at any time by pressing
any button. Press the Maintenance button c to continue rinsing of the filter.
E The water may be slightly discolored. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically after approximately 17 oz
(500 ml). The IMPRESSA heats up and is once more ready for use.
Cleaning the machine
After 220 preparations or 80 switch-on rinses, the IMPRESSA will
prompt you to clean it.
J WARNING
Non-recommended (e.g. liquid) cleaning agents may contain substances that could damage the machine or leave residues.
T Use only original JURA cleaning tablets. These are specially
formulated for your machine.
J WARNING
Harmful and irritating cleaning agent. Harmful if swallowed. Irritating to eyes and skin.
T Keep children AWAY.
T Avoid contact with skin and eyes.
T Avoid generation of dust. Do not inhale dust.
T After contact with skin, wash immediately with plenty of
water. In case of skin irritation, seek medical advice.
T After eye contact, immediately flush eyes with plenty of water
and seek medical advice.
T If swallowed, rinse mouth immediately and drink large quantities of water. Do not induce vomiting. Seek medical advice
immediately and show label.
E The cleaning program lasts approximately 20 minutes.
E Do not interrupt the cleaning program. The quality of cleaning
will be impaired if you do so.
E JURA cleaning tablets are available from specialized dealers.
Precondition: COFFEE READY / CLEAN is displayed and the
Maintenance button c lights up.
c T Press the Maintenance button.
CLEANING TIME 20 MIN / START YES
38
5
Maintenance
E If you do not want to start cleaning just yet, turn the Rotary
Switch until CLEANING / START NO is displayed. Press
the Rotary Switch to exit the maintenance program. The
prompt to clean the machine remains active.
c
c
c
Descaling the machine
J WARNING
T Press the Maintenance button.
TRAY / EMPTY
T Empty the drip tray and coffee grounds container and put
them back into the machine.
PRESS BUTTON, the Maintenance button c lights up.
T Place one receptacle under the coffee spout and another
under the cappuccino frother.
T Press the Maintenance button.
MACHINE IS CLEANING, water flows out of the coffee
spout.
The operation is interrupted, ADD TABLET.
T Open the cover of the bean container.
T Open the cover of the filler funnel for ground coffee.
T Insert a JURA cleaning tablet into the filler funnel.
T Close the cover of the filler funnel and the cover of the bean
container.
PRESS BUTTON, the Maintenance button c lights up.
T Press the Maintenance button.
MACHINE IS CLEANING, water flows repeatedly out
of the coffee spout and the cappuccino frother.
The operation is interrupted, TRAY / GROUNDS EMPTY.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
Cleaning is now complete. The IMPRESSA is once more
ready for use.
The IMPRESSA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of
calcification depends on the hardness of your water.
Non-recommended descaling agents (e.g. vinegar) may contain
substances that could damage the machine or leave residues.
T Use only original JURA descaling tablets. These are specially
formulated for your machine.
39
5
Maintenance
J WARNING
NOTICE
Harmful and irritating descaling agent. Harmful if swallowed. Irritating to eyes and skin.
T Keep children AWAY.
T Avoid contact with skin and eyes.
T Avoid generation of dust. Do not inhale dust.
T After contact with skin, wash immediately with plenty of
water. In case of skin irritation, seek medical advice.
T After eye contact, immediately flush eyes with plenty of water.
Remove contact lenses. Seek medical advice.
T If swallowed, rinse mouth immediately and drink large quantities of water. Do not induce vomiting. Seek medical advice
immediately and show label.
If the descaling operation is interrupted, there may be damage to
the machine.
T Allow the descaling program to run to the end.
E The descaling program lasts approximately 45 minutes.
E JURA descaling tablets are available from specialized dealers.
E If you use a CLEARYL Blue filter cartridge and this is activated,
you will not be prompted to descale.
E If the descaling agent comes into contact with sensitive surfaces (e.g. marble), damage cannot be ruled out. Clean up any
splashes immediately.
Precondition: COFFEE READY / DESCALE is displayed and
the Maintenance button c lights up.
c T Press the Maintenance button.
DECALCIFYING TIME 45 MIN / START YES
E If you do not want to start descaling just yet, turn the Rotary
Switch until DECALCIFYING / START NO is displayed.
Press the Rotary Switch to exit the maintenance program. The
prompt to descale the machine remains active.
c
T Press the Maintenance button.
TRAY / GROUNDS EMPTY
T Empty the drip tray and coffee grounds container and put
them back into the machine.
SOLVENT IN TANK
40
5
c
Maintenance
T Remove and empty the water tank.
T Completely dissolve the contents of one blister (three JURA
descaling tablets) in a receptacle holding 20 oz (600 ml) of
water. This may take several minutes.
T Pour the solution into the empty water tank and insert it into
the machine.
SOLVENT IN TANK / PRESS BUTTON, the Maintenance button c lights up.
T Remove the cappuccino frother.
T Place one receptacle under the hot-water spout and another
under the connector of the cappuccino frother.
T Press the Maintenance button.
MACHINE IS DECALCIFYING
Water flows out of the hot-water spout and the connector of
the cappuccino frother. The Maintenance button flashes
during the descaling operation.
The operation stops automatically, TRAY / GROUNDS
EMPTY.
T Empty the receptacles from under the hot-water spout and
the connector of the cappuccino frother.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
WATER TANK FILL
c
T Remove the water tank and rinse it thoroughly.
T Fill the water tank with fresh, cold water and reinsert the
tank.
PRESS BUTTON, the Maintenance button c lights up.
T Refit the cappuccino frother.
T Place one receptacle under the hot-water and coffee spout
and another under the cappuccino frother.
T Press the Maintenance button.
MACHINE IS DECALCIFYING, water flows out of
the cappuccino frother and the hot-water spout.
UNIT IS HEATING, RINSING, water flows out of the
coffee spout.
The operation stops automatically, TRAY / GROUNDS
EMPTY.
41
5
Maintenance
T Empty the drip tray and coffee grounds container and put
them back into the machine.
Descaling is now complete. The IMPRESSA heats up and is
once more ready for use.
E If the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
Cleaning the bean
container
Coffee beans may be covered with a slight oil film which remains on
the walls of the bean container. These traces may negatively affect
the coffee result. For this reason clean the bean container from time
to time.
Precondition: COFFEE READY / FILL BEANS is displayed.
k T Switch the machine off with the On/Off button.
3 T Switch the machine off at the power switch.
T Open the bean container cover and remove the aroma preservation cover.
T Clean the bean container with a soft, dry cloth.
T Fill the bean container with coffee beans, then close the
aroma preservation cover and the bean container cover.
Descaling the water tank
42
Limescale deposits may form in the water tank. To ensure correct
function of the machine, descale the water tank from time to time.
T Remove the water tank.
T If you use a CLEARYL Blue filter cartridge, remove this.
T Descale the tank with a mild conventional descaling agent
in accordance with the manufacturer's instructions.
T Rinse out the water tank thoroughly.
T If you use a CLEARYL Blue filter cartridge, insert this again.
T Fill the water tank with fresh, cold water and reinsert the
tank.
6 Display messages
6 Display messages
Message
Cause/Result
Action
WATER TANK FILL
The water tank is empty.
You cannot prepare any
products.
T Fill the water tank (see
Chapter 1 ‘Preparing and using
for the first time – Filling the
water tank’).
GROUNDS EMPTY
The coffee grounds container
is full.
You cannot prepare any coffee
products, but you can prepare
hot water and milk.
T Empty the coffee grounds
container and the drip tray.
TRAY EMPTY
The drip tray is full.
You cannot prepare any
products.
T Empty the drip tray.
T Clean and dry the metal
contacts on the back of the
drip tray.
TRAY MISSING
The drip tray is not inserted
correctly or is not inserted at
all.
You cannot prepare any
products.
T Fit the drip tray.
COFFEE TRAY MISSING The coffee grounds container
is not inserted correctly or is
not inserted at all.
You cannot prepare any
products.
T Fit the coffee grounds
container.
PRESS RINSE
The IMPRESSA is prompting
you to perform a rinse or
continue a maintenance
program that was already
started.
T Press the Maintenance
button to start the rinse or to
continue the maintenance
program.
COFFEE READY /
FILL BEANS
The bean container is empty.
You cannot prepare any coffee
products, but you can prepare
hot water and milk.
T Fill the bean container (see
Chapter 1 ‘Preparing and using
for the first time – Filling the
bean container’).
43
6 Display messages
Message
Cause/Result
Action
COFFEE READY /
CAPPU RINSE
The IMPRESSA requests a
cappuccino rinse.
T Press the Maintenance
button to start the cappuccino
rinse.
POWDERFUNNEL
The filler funnel for ground
coffee is not fitted.
T Fit the filler funnel.
COFFEE READY / CLEAN
or CLEAN (flashing),
CLEAN NOW / CLEAN
(flashing)
The IMPRESSA is prompting
you to clean it.
T Perform cleaning (see
Chapter 5 ‘Maintenance –
Cleaning the machine’).
COFFEE READY /
DESCALE or DESCALE
(flashing), DESCALCIFY
NOW / DESCALE (flashing)
COFFEE READY /
FILTER CHANGE or
FILTER CHANGE
(flashing), CHANGE NOW /
FILTER CHANGE
The IMPRESSA is prompting
you to descale it.
T Perform descaling (see
Chapter 5 ‘Maintenance –
Descaling the machine’).
The filter cartridge no longer
works.
T Replace the CLEARYL Blue
filter cartridge (see Chapter 5
‘Maintenance – Changing the
filter’).
BEANCOVER / MISSING
The aroma preservation cover
is not inserted correctly or is
not inserted at all.
You cannot prepare any coffee
products, but you can prepare
hot water and milk.
T Fit the aroma preservation
cover.
PRE-GROUND / NOT
ENOUGH
There is insufficient ground
T The next time you prepare a
coffee in the machine; the
beverage, add more ground
IMPRESSA stops the operation. coffee (see Chapter 2 ‘Preparation – Ground coffee’).
(flashing)
44
7
7
Troubleshooting
Troubleshooting
Problem
Cause/Result
Action
Insufficient foam is produced
when the milk is frothed or
milk sprays from the cappuccino frother.
The cappuccino frother is
dirty.
T Rinse and clean the cappuccino frother (see Chapter 5
‘Maintenance – Rinsing the
cappuccino frother’).
Coffee only comes out in drips
when it is being prepared.
Coffee or ground coffee has
been ground too finely and
is blocking the system.
T Set the grinder to a coarser
setting or use coarser ground
coffee (see Chapter 1 ‘Preparing
and using for the first time –
Adjusting the grinder’).
Water hardness cannot be
adjusted.
The CLEARYL Blue filter
cartridge is activated.
T Deactivate the filter cartridge
in programming mode.
COFFEE READY / FILL
BEANS is not displayed
The bean monitor is dirty.
T Clean the bean container (see
Chapter 5 ‘Maintenance –
Cleaning the bean container’).
The metal contacts of the
drip tray are dirty or wet.
T Clean and dry the metal
contacts on the back of the drip
tray.
The water tank float is
trapped.
T Descale the water tank (see
Chapter 5 ‘Maintenance –
Descaling the water tank’).
Grinder is making a very
loud noise.
There are foreign objects in
the grinder.
T Contact customer support in
your country (see Chapter 11
‘JURA contact details / Legal
information’).
ERROR 2 is displayed.
If the machine was exposed
to the cold for a long period
of time, heating is disabled
for safety reasons.
T Warm the machine at room
temperature.
–
T Contact customer support in
your country (see Chapter 11
‘JURA contact details / Legal
information’).
although the bean container
is empty.
TRAY EMPTY is always
displayed.
WATER TANK FILL
is displayed although the
water tank is full.
Other ERROR messages are
displayed.
45
7
Troubleshooting
Problem
Cause/Result
Action
Little or no water or steam
comes out of the cappuccino
frother. The pump is very
quiet.
The connector of the
cappuccino frother may
be blocked by milk residues
or limescale fragments
loosened during descaling.
T Remove the cappuccino
frother.
T Unscrew the black connector
with the aid of the hexagonal
hole on the measuring spoon
for ground coffee.
T Clean the connector
thoroughly.
T Screw the connector back on
by hand.
T Carefully tighten it using the
hexagonal hole on the
measuring spoon, turning by no
more than a quarter of a
rotation.
E If you were unable to solve the problem, contact customer
support in your country (see Chapter 11 ‘JURA contact details /
Legal information’).
46
8
8
Transport and environmentally friendly disposal
Transport and environmentally friendly disposal
Transport / Emptying
the system
In order to protect the IMPRESSA from frost during transport, the
system must be emptied.
Precondition: COFFEE READY is displayed.
k T Press and hold the Rotary Switch until MAINTENANCE
appears.
g T Turn the Rotary Switch until RESET is displayed.
k T Press the Rotary Switch to enter the program item.
RESET / PRODUCT
g T Turn the Rotary Switch until RESET / EMPTY SYSTEM
is displayed.
k T Press the Rotary Switch.
WATER TANK EMPTY
c
Disposal
T Remove the water tank.
PRESS RINSE, the Maintenance button c lights up.
T Place one receptacle under the hot-water spout and another
under the cappuccino frother.
T Press the Maintenance button.
EMPTYING, a small amount of water flows out of the hotwater spout and the cappuccino frother. The operation stops
automatically and your IMPRESSA switches off.
Please dispose of old machines in an environmentally friendly way.
H
47
9 Technical data
9 Technical data
Voltage
120 V ~, 60 Hz
Power
1350 W
Safety test
Directives
Energy consumption SAVE NO
Approx. 23 Wh
Energy consumption SAVE LEVEL1
Approx. 16 Wh
Energy consumption SAVE LEVEL2
Approx. 6 Wh
Pump pressure
Static, max. 15 bar
Holding capacity of water tank
96 oz
(2.8 l)
Holding capacity of bean container
10 oz
(280 g)
Holding capacity of coffee grounds
container
Max. 20 portions
Power cord length
Approx. 59 in.
(Approx. 1.5 m)
Weight
30.4 lb
(13.8 kg)
Dimensions (W  H  D)
12.2  14.76  17.7 in.
(31  37.5  45 cm)
The machine complies with the following directives:
Standard UL 1082,
Canadian Standard CSA C22.2 No. 64
U
U
48
Index
10
A
B
C
Index
Customer support 52
Addresses 52
Automatic switch-off 28
D
Bean container 8
Bean container with aroma preservation
cover 8
Cleaning 42
Filling 11
Bus bar
Technical data 48
Button
Cappuccino button 9
Coffee button 9
Espresso button 9
Hot Water button 9
Latte Macchiato button 9
Maintenance button 9
Milk button 9
On/Off button 9
Ristretto button 9
Special Coffee button 9
E
Cappuccino 17
Cappuccino frother
Cleaning 35
Rinsing 35
Cleaning
Bean container 42
Cappuccino frother 35
Machine 38
CLEARYL Blue filter cartridge
Changing 37
Inserting and activating the filter 12
Coffee 16
Coffee grounds container 8
Coffee spout
Height- and width-adjustable coffee
spout 8
Consistency of grind
Adjusting the grinder 15
Grinder adjustment switch 8
Contact details 52
Cup platform 8
F
G
H
I
Degree of water hardness 13
Descaling
Machine 39
Water tank 42
Determining and adjusting the water
hardness 13
Display 9
Display messages 43
Display messages 43
Drip tray 8
Emptying the system 47
Energy-saving mode 27
Errors
Troubleshooting 45
Espresso 16
Factory settings
Restore factory settings 31
Filler funnel
Filler funnel for ground coffee 8
Filling
Bean container 11
Water tank 10
Filter
Changing 37
Inserting and activating the filter 12
First-time use 11
Frother
Cappuccino frother 8
Ground coffee 18
Hotline 52
Hot milk 18
Hot water 20
Hot-water spout 8
Important safeguards
Safety 4
Internet 10
49
Index
J
K
L
M
P
JURA
Contact details 52
Internet 10
Restore factory settings 31
Rinses 28
Unit for amount of water 32
R
Knowledge Builder 10
Language 33
Latte macchiato 17
Machine
Cleaning 38
Descaling 39
Rinsing 34
Setting up 10
Switching off 22
Switching on 21
Maintenance
Daily maintenance 21
Maintenance 34
Milk
Hot 18
Milk foam 18
Permanently setting the water for the cup
size 19
Permanent settings in programming mode
23
Preparation 16, 17
Cappuccino 17
Coffee 16
Espresso 16
Ground coffee 18
Latte macchiato 17
Milk 18
Ristretto 16
Special coffee 17
Problems
Troubleshooting 45
Programming mode 23
Automatic switch-off 28
Energy-saving mode 27
Language 33
Logo 30
Products 24
50
S
T
U
Rinses 28
Rinsing
Cappuccino frother 35
Machine 34
Ristretto 16
Rotary Switch 9
Safety
Important safeguards 4
Settings
Permanent settings in programming
mode 23
Setting up
Setting up the machine 10
Short operating instructions 10
Special coffee 17
Switching off 22
Switching on 21
Switch-off
Automatic switch-off 28
Symbol description 3
Technical data 48
Telefon 52
Troubleshooting 45
Unit for amount of water 32
Use, First-time 11
W
Water tank 8
Descaling 42
Filling 10
Website 10
– intentionally blank –
51