AXIS T8342 Door/Window Sensor
User Manual
AXIS T8342 Door/Window Sensor
Table of Contents
Solution overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to add a device to a Z-Wave Network . . . . . . . . . . . . . . . . . . . . . .
How to test the Z-Wave device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operational guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to program the Z-Wave device . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
3
4
5
6
6
7
10
11
AXIS T8342 Door/Window Sensor
Solution overview
Solution overview
The device is Z-Wave® enabled and fully compatible with any Z-Wave enabled network. The device can be set up in a Z-Wave
network to communicate directly with other end devices such as lighting controllers, or to report directly to a Z-Wave controller like
the AXIS M5065 PTZ Network Camera.
3
AXIS T8342 Door/Window Sensor
Product overview
Product overview
1. LED
2. Battery
3. Tamper switch
4. Magnet
5. Detector
6. Screw hanger
7. Battery protection film
4
AXIS T8342 Door/Window Sensor
How to add a device to a Z-Wave Network
How to add a device to a Z-Wave Network
Auto inclusion
The detector supports the auto inclusion feature where it will automatically enter Inclusion mode when first powered up.
1. Put a Z-Wave controller into inclusion mode.
2. Remove the strip of battery protection film sticking out from the battery cover on the front of the casing. The LED on
the device should turn ON.
3. Enter PIN number into the Z-Wave controller. The PIN number can be found on the device. See where in the installation
guide.
4. The inclusion process should be completed when the LED stops blinking.
5. Perform test before you refit the battery cover. See How to test the Z-Wave Device.
Manual inclusion
You can also choose to manually add the Z-Wave device to a control device. Please follow the steps described below.
Note
For best results, exclude the device before starting the inclusion process. For more details see the installation guide.
1. Remove the battery cover.
2. Press the tamper switch 3 times within 1.5 seconds to put the unit into learning (inclusion/exclusion) mode.
3. Enter PIN number into the Z-Wave controller. The PIN number can be found on the device. See where in the installation
guide.
4. The inclusion process should be completed when the LED stops blinking
5. Perform test before you refit the battery cover. See How to test the Z-Wave Device.
Manual exclusion
1. Remove the battery cover.
2. Press the tamper switch 3 times within 1.5 seconds to put the unit into learning (inclusion/exclusion) mode.
3. The exclusion process should be completed when the LED stops blinking
4. Refit the battery cover.
5
AXIS T8342 Door/Window Sensor
How to test the Z-Wave device
How to test the Z-Wave device
•
Remove the battery cover with the tamper switch not being pressed on the detector (test mode)
•
Separate the magnet from the detector. The detector should then flash.
•
Put the battery cover back on the detector, and the detector will enter normal mode.
Note
If you have removed the batteries, wait 5 seconds before you refit them.
Operational guidelines
•
Due to the limited power supplied from the batteries, the device may not operate continuously for an extended period of
time. Therefore, the set up time for device should be minimized, and repeated presses of the tamper switch should be
avoided, in order to prevent incidents caused by a quick battery voltage drop.
•
You can enter test mode by releasing the tamper switch. If the magnetic sensor is triggered during that time, then the LED
will be illuminated. You can confirm whether the tamper switch has been pressed properly by testing this function.
•
When the tamper switch has been pressed and the device has entered normal mode, the LED will not be illuminated even
if the magnetic sensor is triggered, unless low battery is detected.
6
AXIS T8342 Door/Window Sensor
How to program the Z-Wave device
How to program the Z-Wave device
Note
Programming Z-Wave devices using a Z-Wave controller is recommended for experienced users only.
Z-Wave Group
The detector supports either one of two Z-Wave Association Groups:
Group 1: Association with 1 controller node.
Group 2: Association with 4 nodes (i.e. end devices such as smart plugs and other lighting controllers). This allows the detector to
transfer commands directly to end devices without the participation of the controller. This has the effect that when the detector
triggers, all devices associated with detector will be operated.
Note
Association-group support can vary among Z-Wave Controllers. The AXIS M5065 supports Z-Wave Association Group 1.
Group 1 commands:
•
If the device already is a part of a Z-Wave network when powered up, the device will send a Notification Report to
the node in Group 1.
•
When setting up the device or changing the device’s status, the device will send a Binary Switch Report to the node of
Group 1. When the device is turned OFF, the Switch Binary Report Value = 0x00. When the device is turned ON, the
Switch Binary Report Value = 0xFF.
•
Device Reset: When performing Factory Reset, the device will send Device Reset Locally Notification to the node of Group1.
Group 2 commands:
•
When the button on the device is pressed, the device will send a Basic Set command to the nodes of Group 2. When the
device is OFF, Basic Set Value = 0x00. When the unit is ON, Basic Set Value = 0xFF
® info
Z-Wave Plus®
Role type
Node type
Installer Icon
User Icon
Slave Sleeping report
Z-Wave Plus node
Sensor Notification Device Type
(Access Control)
Sensor Notification Device Type
(Access Control)
Version
Protocol library
3 (Slave_Enhance_232_Library)
Protocol version
4.6 ( 6.71.00)
Manufacturer
Manufacturer ID
Product Type
Product ID
0x0364
0x0003
0x0001
AGI (Association Group Information) table
7
AXIS T8342 Door/Window Sensor
How to program the Z-Wave device
Group
Profile
Command Class & Command
(List) N bytes
Group Name (UTF-8)
1
General
Notification Report
Device Reset Locally Notification
Lifeline
2
Control
Basic Set
PIR Control
Notification
Event
Type
Event
Event Parameters
Length
The power is applied for the first time
0x08
0x01
null
The battery is Low
0x08
0x0A
null
Door sensor trigger OPEN
0x06
0x16
null
Door sensor detector trigger Close
0x06
0x17
null
Tamper switch pressed for more than 10 seconds
and then released
0x07
0x03
null
Tamper switch pressed
0x07
0x00
null
Battery
Battery Report (value)
Description
0x64
Battery is high
0x10
Battery is normal
0xFF
Battery is low
Command classes
This product supports the following command classes:
•
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
•
COMMAND_CLASS_ASSOCIATION_V2
•
COMMAND_CLASS_ASSOCIATION_GRP_INFO
•
COMMAND_CLASS_TRANSPORT_SERVICE_V2
•
COMMAND_CLASS_VERSION_V2
•
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
•
COMMAND_CLASS_DEVICE_RESET_LOCALLY
•
COMMAND_CLASS_POWERLEVEL
•
COMMAND_CLASS_SECURITY
•
COMMAND_CLASS_SECURITY_2
•
COMMAND_CLASS_SUPERVISION
•
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
•
COMMAND_CLASS_BATTERY
8
Event Parameters
AXIS T8342 Door/Window Sensor
How to program the Z-Wave device
•
COMMAND_CLASS_WAKE_UP_V2
•
COMMAND_CLASS_NOTIFICATION_V4
Wake up command class
After the detector has been included into a Z-Wave network it will go to sleep, but it will send a wake-up notification command to
the controller periodically at a preset period . The detector will stay awake for at least 10 seconds and then go back to sleep to
conserve battery life.
The time interval between wake up notification commands can be set in the wake up command class based on the range values below:
Minimum wake up interval
600s (10 minutes)
Maximum wake up interval
86400s (1 day)
Default wake up interval
14400s (4 hours)
Wake up interval step seconds
600s (10 minutes)
9
AXIS T8342 Door/Window Sensor
Troubleshooting
Troubleshooting
The table below explains the status in the Z-Wave controller as well as the LED indication on the device.
Action/Status
Description
LED indication
No node ID.
The Z-Wave controller could not find the device and did not
provide a node ID.
2-second on, 2-second off for 2
minutes.
Factory Reset
1. Press the tamper switch 3 times within 1.5 seconds to put the
unit into exclusion mode.
(This procedure
should only be used
when the controller
is inoperable.)
2. Within 1 second of step 1, press the tamper switch again and
hold for 5 seconds.
3. Node ID is excluded. The device reverts to factory default state.
2-second on, 2-second off for 2
minutes.
Failed or successful results in including/excluding the ID can be viewed on the Z-Wave Controller.
Table below lists typical problems encountered:
Symptom
Possible cause
Recommendation
Cannot carry out inclusion
and association.
1. The device is still connected, or has been
accidentally included, to a previous network.
2. The entered PIN code is incorrect
3. The battery has run out of power.
4. Battery polarity is reversed.
5. Detector is malfunctioning.
1. Exclude the device before
including it again.
2. Make sure you have
entered the correct PIN
code
3. Replace the battery.
4. Refit the battery with the
correct polarity.
5. Ensure the detector is
working properly.
Cannot control the connected
modules.
1. The device is still connected, or has been
accidentally included, to a previous network.
2. The battery has run out of power.
3. Detector is malfunctioning.
1. Exclude the device before
including it again.
2. Replace the battery.
3. Ensure the detector is
working properly.
The detector is not working.
1. The device is still connected, or has been
accidentally included, to a previous network.
2. The battery has run out of power.
3. Distance between the Alert Button and the
receiver(s) too far.
4. Detector is malfunctioning.
1. Exclude the device before
including it again.
2. Replace the battery.
3. Move closer to the
receivers.
4. Ensure the detector is
working properly.
Note
For best results, exclude the device before starting the inclusion process. For more details see the installation guide.
10
AXIS T8342 Door/Window Sensor
Specifications
Specifications
To find the latest version of the product’s datasheet, go to the product page on axis.com and locate Support & Documentation.
Specifications
Battery
CR2450 3.0V Lithium Battery x 2
Battery life
1 year*
Range
Up to 100 meters line of sight
Frequency range
908.42 MHz (US), 922.5 MHz (JP)
Specifications are subject to change without notice
*measured at 10 triggers per day
11
User Manual
AXIS T8342 Door/Window Sensor
© Axis Communications AB, 2017 - 2018
Ver. M1.7
Date: January 2018
Part No. T10117078
Download PDF

advertising