BVF 23-FA - UHS | Electric Floor Heating | Infra Panel

User manual
BVF 23-FA
RF Thermostat with plug receiver
TECHNICAL DATA
Thermostat Operating Voltage: 2 x AAA 1.5V, alkaline batteries
Receiver Current Load:
230V, 50/60Hz
Backup Storage:
EEPROM
Maximum load:
230V / 16A
Frequency:
868MHz / 433MHz
Switching options:
5+1+1 day, 4 periods each day
Temperature settings:
5°C ~ 30°C, 0.5°C increments
Accuracy:
+/- 0.5°C
Thermostat dimensions:
135mm x 88mm x 22mm
Receiver dimensions:
114mm x 86mm x 30mm
Color:White
IP protection rating:
20
Certification:
CE
PRODUCT FEATURES
•
•
•
•
•
•
Large display can be clearly read with the background
lighting
Easy to fit without installation works
Six buttons make it easy to use
4 periods of each day programmable (5+1+1)
The display shows the set and the measured temperature
The thermostat is supplied with a wall-fixing fram and
desktop stand
The unit consists of two parts: 23-F controller and 23-A receiver. The controller has been developed to operate electric heating panels or conventional electric heating units. Receiver part is designed for standard electric outlet. The controller can be accommodated anywhere in the room.
1. DISPLAY AND BUTTONS
11
13
1
10
9
12
14
15
2
8
3
7
6 5 4
1
+ button
Increase temperature (change value at settings)
12 Power on LED indicator
2
– button
Decrease temperature (change value at settings)
13 Heating on LED indicator
3
Back
Back to main page
14 Setup in progress LED indicator
4
Menu
Set time / Select Mode
15 Pairing device button
5
PRG
Programming
6
On/Off
Turn unit On /Off
7
Actual mode
Displays actual mode
8
Temperature
Displays actual temperature
9
Clock
Displays actual time
10 Weekday
Displays actual weekday
11 Cycle time
Displays actual cycle time
www.bvfheating.com
User manual
2. TEMPERATURE CALIBRATION
You might need to calibrate the temperature sensor for the first use. Turn off the controller, press and hold the MENU button for 3 seconds. Use
the + and – buttons to set the temperature value. This value can be adjusted within -8 to +8°C in 0,5°C increments.
3. SETUP TIME AND SELECT MODE
Set up actual time and weekday
After turning the controller on, press MENU button and hold 3 seconds, the time display will start flashing. Change the minutes by + and –
button. Press MENU button again, and change the hours. Press MENU button again and set the day of the week: 1-Monday; 2-Tuesday etc. After
setting up time and day push the BACK button to save changes.
Select mode
The controller offers four different pre-set modes. The PRG mode sets up temperature using 4 different programmed cycle times a day. The
Comfort mode
, Energy saving mode
and the holiday mode
keeps the assigned temperature all around the week.
You may switch between modes using MENU button.
4. SETUP PROGRAM MODE
Pre-set factory values of the program mode might be modified easy as follows:
Monday to Friday
Saturday
Sunday
Cycle
1
2
3
4
1
2
3
4
1
2
3
4
Time
6:30
8:00
18:00
22:30
8:00
10:00
18:00
23:00
9:00
12:00
19:00
0:00
Temperature
21°C
18°C
21°C
16°C
21°C
21°C
21°C
16°C
23°C
21°C
16°C
21°C
B
A
D
Weekdays are displayed on the top left area of the screen (B) from Monday to Sunday (1-7). You can
adjust cycle times (D) and temperatures (C) for each period: one for the working days (1-5), one for
Saturday (6) and one for Sunday (7). All three periods have a daily routine of four cycles with its own
starting time and temperature value.
C
1.
To modify values in program mode press PRG button for 3 seconds. Time starts flashing (A) Set
the starting time of the cycle within the period using + and – buttons, and after pushing PRG
button again, set the desired temperature value of the cycle.
2.
Press PRG button and display will jump to the next cycle. Program all values of the working
days, then Saturday and Sunday.
3.
You may save changes and return using the BACK button.
5. PAIRING WITH THE RECEIVER
The receiver is usually paired with the receiver; still in some cases you might need to repeat pairing, which is fast and easy:
1.
Connect the receiver to the power outlet. The
2.
Push the pairing button on the receiver. The LED light starts flashing.
LED light turns on.
3.
Turn thermostat off and press MENU for 3 sec. The LED turns off, pairing is ready. When you set the temperature higher than room
temperature, the
LED will light.
6. MOUNTING
Mounting on wall:
www.bvfheating.com
Desktop:
Download PDF

advertising