Ancona Range Hood GCD430 GCD436 AN-1503

®
Ancona Range Hood
GCD430 GCD436
AN-1503 - AN-1504
User Manual
&
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
Carefully read the important information
regarding installation, safety and maintenance.
Keep these instructions for future reference.
MAAN1503-EN-01
2017-06-13
Before You Begin
INSTALLERS - Start Here
Safety Instructions are on pages 4 and 5 and
Installation Instructions are on pages 9 to 15.
Please perform these steps:
1. Read the safety instructions.
2. Read all instructions in the Installation section of
this manual BEFORE installing the range hood.
3. Remove all packing materials.
4. When finished, make sure to leave these instructions with the consumer.
5. Installation is to be done by a qualified technician only. However, the
ultimate responsibility for proper installation falls to the owner.
6. Product failure due to improper installation is not covered under the Warranty.
CONSUMERS - Start Here
Safety Instructions are on pages 4 and 5 and
Operating Instructions are on pages 16 and 17.
Please perform these steps:
1. Read the safety instructions.
2. Read all instructions in the manual BEFORE
operating the range hood.
3. Remove all packing materials.
4. Installation is to be done by a qualified technician only. However, the
ultimate responsibility for proper installation falls to the owner.
5. Product failure due to improper installation is not covered under the Warranty.
Hardware Note: For safety reasons, range hood mounting screws and anchors will not be
included due to the variation of cabinetry constructions and wall material. Please consult your
installation specialist regarding the optimal type of mounting screws and wall anchors to suit your
home’s construction.
—2—
Table of Contents
Before You Begin................................................................................................................................ 2
Table of Contents............................................................................................................................... 3
Important Safety Information............................................................................................................. 4
Included Parts.................................................................................................................................... 6
Range Hood Dimensions................................................................................................................... 7
Specifications..................................................................................................................................... 7
Mounting Brackets............................................................................................................................. 8
Installation.......................................................................................................................................... 9
Step 1 - Read the Safety Instructions............................................................................................. 9
Step 2 - Unpack Range Hood and Prepare Tools........................................................................... 9
Step 3 - Plan Desired Location....................................................................................................... 9
Step 4 - Test Unit Functions........................................................................................................... 9
Step 5 - Venting Installation Guidelines........................................................................................ 10
Step 6 - Preparations.................................................................................................................... 12
Step 7 - Installing the Hood Mounting Bracket............................................................................ 12
Step 8 - Installing the Upper Chimney Bracket............................................................................ 12
Step 9 - Installing the Glass.......................................................................................................... 12
Step 10 - Installing the Damper.................................................................................................... 13
Step 11 - Mount Range Hood Onto Wall...................................................................................... 13
Step 12 - Connect Ductwork........................................................................................................ 13
Step 13 - Install Chimney ............................................................................................................. 14
Step 14 - Connect to AC.............................................................................................................. 14
Step 15 - Install Filters.................................................................................................................. 15
Operation......................................................................................................................................... 16
Power Settings.............................................................................................................................. 16
Timer Function.............................................................................................................................. 16
Lights............................................................................................................................................ 16
Maintenance.................................................................................................................................... 17
Replacing the Light Bulbs............................................................................................................. 17
Range Hood Assembly.................................................................................................................... 18
Assembly.......................................................................................................................................... 19
Circuit Diagram............................................................................................................................. 19
Blower Assembly.......................................................................................................................... 19
Electrical Assembly....................................................................................................................... 19
Use and Care information................................................................................................................ 20
—3—
Important Safety Information
READ ALL INSTRUCTIONS BEFORE USE
Read and follow all instructions before using the range hood to prevent the risk of fire, electric shock,
personal injury, or damage when using the range hood or appliances with the range hood. This guide
does not cover all possible conditions that may occur. Always contact your service technician or
manufacturer about problems that you do not understand.
• The installation in this manual is intended
for qualified installers, service technicians or
persons with a similar qualified background.
Installation must be done by qualified
professionals and in accordance with all
applicable codes and standards, including
fire-rated construction.
• The range hood may have very sharp
edges; please wear protective gloves if it is
necessary to remove any parts for installing,
cleaning or servicing.
• Activating any switch to ON position before
completing installation may cause damage or
electric shock.
• Due to the size of this range hood, a twoperson installation is recommended.
To reduce the risk of fire, electric shock, or
injury to persons:
• For general ventilating use only. DO NOT use
to exhaust hazardous or explosive materials
and vapours.
disconnecting means to prevent power from
being switched on accidentally. When the
service disconnecting means cannot be
locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
• Clean grease-laden surfaces frequently. To
optimize performance and to disperse air
properly, make sure to vent air outside. DO
NOT vent exhaust into spaces between walls,
crawl spaces, ceilings, attics or garages.
• Ducted fans MUST always be vented to
the outdoors.
• This unit MUST be grounded and used with
metal ductwork only.
• Sufficient air is needed for proper combustion
and exhausting of gases through the duct to
prevent back drafting.
• When cutting or drilling into wall or ceiling, be
careful not to damage electrical wiring or other
hidden utilities.
• All electrical wiring must be properly installed,
insulated and grounded.
• WARNING: To Reduce The Risk Of Fire Or
Electric Shock, Do Not Use This Fan With Any
Solid-State Speed Control Device.
• Old ductwork should be cleaned or replaced
if necessary to avoid the possibility of a
grease fire.
• The combustion air flow needed for safe
operation of fuel-burning equipment may be
affected by this unit’s operation. Follow the
heating equipment manufacturer’s guideline
and safety standards such as those published
by the National Fire Protection Association
(NFPA), and the American Society of Heating,
Refrigeration and Air Conditioning Engineers
(ASHRAE), and other local code authorities.
• Check all joints on ductwork to ensure
proper connection; all joints should be
properly taped using a certified aluminum
or foil tape.
• Use this unit only in the manner intended
by the manufacturer. If you have questions,
contact the vendor.
READ AND SAVE THESE
INSTRUCTIONS
• Before servicing or cleaning the unit, switch
power off at service panel and lock the service
—4—
Important Safety Information
WARNING: TO REDUCE RISK OF A RANGE
TOP GREASE FIRE:
To reduce the risk of injury to persons in the
event of a gas leaks:
a) Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on
low or medium settings.
• Extinguish any open flame.
• DO NOT turn on the lights or any type of appliance.
• Open all doors and windows to disperse the
gas. If you still smell gas, call the gas company
and fire department.
b) Always turn range hood ON when cooking at
high heat or when flambéing food (i.e. Crepes
Suzette, Cherries Jubilee, etc.).
Your safety and the safety of others is very
important. We have provided many important
c) Clean ventilating fans frequently. Grease should
safety messages in this manual and on your
not be allowed to accumulate on fan or filter.
appliance. Always read and obey all safety
Before servicing or cleaning unit, unplug and
messages. All safety messages outline any
disconnect the hood from the power supply.
potential hazards, how to reduce the chance of
d) Use proper pan size. Always use cookware
injury, and possible risks if the instructions are not
appropriate for the size of the surface element. followed.
WARNING: TO REDUCE RISK OF INJURY TO
PERSONS IN THE EVENT OF A RANGE TOP
GREASE FIRE, OBSERVE THE FOLLOWING *
READ AND SAVE THESE
INSTRUCTIONS
a) SMOTHER FLAMES with a close-fitting
lid, cookie sheet, or metal tray, then turn
off the burner. BE CAREFUL TO PREVENT
BURNS. If the flames do not go out
immediately, EVACUATE AND CALL THE
FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - You may
be burned.
c) DO NOT USE WATER, including wet dishcloths
or towels - a violent steam explosion will result.
d) Use an extinguisher ONLY if:
1) You know you have a Class A, B, C
extinguisher, and you already know how to
operate it.
2) The fire is small and contained in the area
where it is started.
3) The fire department is being called.
4) You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips”
published by NFPA
—5—
Included Parts
Damper
Range Hood
Hood Mounting Bracket
Lower Chimney
Upper Chimney Bracket
Lower Chimney Bracket
Upper Chimney
4 x Screws / Washers
Installation of Glass Canopy
1 Filter
4 x Damper Screws
4 x Chimney Screws
Hardware Note: For safety reasons, range hood mounting screws and anchors will not be included due to
the variation of cabinetry constructions and wall material. Please consult your installation specialist regarding
the optimal type of mounting screws and wall anchors to suit your home’s construction.
—6—
Range Hood Dimensions
10.8”(275 mm)
12”
(305 mm)
19” - 37.75”
(480 mm 954 mm)
10
(2
mm)
2.72”
(69 mm)
19 ”
mm)
Glass Depth
15” (380 mm)
19.6” (500 mm)
15.71” (399 mm)
29.52” (750 mm) / 35.4” (900 mm)
Specifications
Body Design
Power Rating
Stainless Steel
120 V / 60 Hz (cETLus Certified)
Total Input Power
235.1 W
Motor Input Power
230 W
Total Amps
1.96 A
Speed Control Levels
3 Levels
Interference Levels
Motors
Radio Frequency Interference Protected
Single Motor
Control
Electronic Control Panel
Filtration
Illumination
Stainless Steel Baffle Filters
2 x 2.55 W LED
Venting Size
Top Round 6 inches (152 mm)
—7—
Mounting Brackets
Upper Chimney Bracket
Lower Chimney Bracket
Mounting Bracket Hook
—8—
Installation
STEP 1
Read the Safety Instructions
•
It is very important to read the safety instructions on pages 4 and 5.
IMPORTANT: It is the installer’s responsibility to comply with installation clearances.
STEP 2
Unpack Range Hood and Prepare Tools
•
Carefully unpack the range hood and parts. Make sure all parts are included as shown on page 6.
•
DO NOT remove the protective film covering the appliance until the installation is fully completed.
•
Consult a qualified and trained installer or check local codes for makeup air requirement, if any.
STEP 3
Plan Desired Location
• Plan a desirable location that fits all requirements in the Safety and Installation sections of this manual. Plan where
and how the ductwork will be installed.
• A straight or short duct run will allow the unit to perform most efficiently. Long duct runs, elbows and transitions
will reduce the performance of the unit. Each elbow is equivalent to 5 to 10 feet (1.5 m to 3 m) of straight run.
Proper size duct work should be 6 inches (152 mm) in diameter.
• To reach a 9 foot (2.7 m) ceiling make sure hood is installed 30 inches (76.2 cm) from cooking surface. If
you have a ceiling greater than 9ft, please visit anconahome.com to order a chimney extension.
•
If ductwork is already installed: ensure ductwork is free from debris and measures 6 inches (152 mm).
STEP 4
Test Unit Functions
•
Plug the unit in and test all of the functions before installing.
•
Place the range hood on a flat, stable surface. Connect the range hood to a designated standard outlet (120-Volt, 60Hz,
AC only) and turn on the range hood. Verify all operations of the range hood by referring to Range Hood Operations.
•
Turn power On in control panel.
•
Check all lights and fan operations.
WARNINGS:
• Please make sure to read ALL safety instructions on pages 4 and 5.
• Use two or more people to move and install range hood.
• Failure to follow these instructions can result in serious injury.
—9—
Installation
STEP 5
Venting Installation Guidelines
•
The following steps are for exterior ventilation.
•
If you require a ductless installation, please visit anconahome.com to purchase a recirculation kit.
IMPORTANT:
• Vent system must terminate to the outside (roof or side wall).
• DO NOT terminate the vent system in an attic or other
enclosed area.
• DO NOT use 4 in. (10.2 cm) laundry-type wall caps.
• Use metal/aluminum vent only. A rigid metal/aluminum
vent is recommended.
• DO NOT use a plastic vent.
• Always keep the duct clean to ensure proper airflow.
• Calculate the following figures before installation:
1. Distance from the floor to the ceiling
2. Distance between the floor and the countertop/stove
3. A distance of 24 in. to 30 in. (61 cm to 76.2 cm) is
recommended between stove top and the bottom of
range hood. 30 in. (76.2 cm) minimum is required for
gas stove tops.
4. Height of hood and duct cover.
For the most efficient and quiet operation:
• It is recommended that the range hood be vented
vertically through the roof through 6 in. (15.3 cm) or
bigger round metal/aluminum vent work.
• The size of the vent should be uniform.
• Use no more than three 90° elbows.
• Make sure there is a minimum of 24 in. (61 cm) of
straight vent between the elbows if more than one
elbow is used.
• DO NOT install two elbows together.
• The length of vent system and number of elbows should be
kept to a minimum to provide efficient performance.
• The vent system must have a damper. If roof or wall
cap has a damper, you may remove damper flaps from
damper to increase air flow.
• Only one flange is needed in the aire duct system,
either on top of the motor or outside.
• Use silver tape or duct tape to seal all joints in the
vent system.
• Use caulking to seal exterior wall or roof opening
around the cap.
Height and Clearance
To reach 9 ft (2.74 m) ceiling, make sure
range hood is installed at least
32-1/8 in. (816 mm) from cooking surface.
24 in. (610 mm) Min /
32-1/8 in. (816 mm) Max
— 10 —
Installation
IMPORTANT:
• A minimum of 6 in. (15.2 cm) round or 3-1/4 x 10 in. (25.4 cm
x 8.3 cm) rectangular duct (purchased separately) must be
used to maintain maximum airflow efficiency.
• Always use rigid type metal/aluminum ducts if available to
maximize airflow when connecting to provided duct.
• Please use Duct Run Calculation below to compute
total available duct run when using elbows, transitions
and caps.
• ALWAYS, when possible, reduce the number or
transitions and turns. If long duct run is required,
increase duct size from 6 in. (15.2 cm) to 7 in. (17.7
cm) or 8 in. (20.3 cm). If a reducer is used, install a
long reducer instead of a pancake reducer. Reducing
duct size will restrict airflow and decrease airflow, thus
reduce duct size as far away from opening as possible.
• If turns or transitions are required, install as far away
from opening and as far apart, between two (2), as
possible.
• Minimum mount height between stove top to hood
bottom should be no less than 24-inch (61 cm) for
electric cook tops and minimum of 30-inch (76.2 cm)
for gas stove tops and no higher than 30-inch (76.2 cm)
for electric cook tops.
• It is important to install the hood at the proper mounting
height. Hoods mounted too low could result in heat
damage and fire hazard; while hoods mounted too high
may be hard to reach and will lose its performance and
efficiency.
• If available, also refer to stove top manufacturer’s
height clearance requirements and recommended
hood mounting height above range.
• This range hood is factory set for venting through the roof or wall.
• Vent work can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed.
IMPORTANT:
• NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or
garages. All exhaust must be ducted to the outside.
•
Use metal/aluminum duct work only.
•
Fasten all connections with sheet metal screws and tape all joints with certified Silver Tape or Duct Tape.
•
Use caulking to seal exterior wall or roof opening around the cap.
TOP VENTING
ROOF EXHAUST
TOP VENTING
WALL EXHAUST
— 11 —
Installation
STEP 6
Preparations:
NOTE: To avoid damage to your hood, prevent debris from entering the vent opening.
•
Determine and mark the center line on the ceiling or wall where the range hood will be installed.
•
Make sure there is proper clearance within the ceiling or wall for exhaust vent.
•
Due to the weight and size of this unit, please make sure that the support system or framework being used is stable and
secure in the ceiling or wall.
•
Put a thick, protective covering over counter top, cook top or range to protect from damage or dirt.
•
Remove any hazardous objects around the area when installing.
CAUTION
If moving the cooking range is necessary to install the hood, turn OFF the power on an electric range at the main
electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE
STEP 7
Installing the hood mounting bracket
•
Use a pencil to mark on the wall the desired placement of
the range hood mounting screws.
•
The range hood will be installed on top of this bracket (See
Figure # 1).
•
Using references in Height & Clearance on Page 10 and
Measurements and Diagrams on Page 7, drill 3 holes that
will be used to fix the lower mounting bracket.
STEP 8
Installing the upper chimney bracket
190
Flush to the ceiling
115 115
Fig #1
•
Drill 2 holes according to the size of the upper mounting bracket. The upper mounting bracket should be positioned
flush with the top of the outside chimney (See Figure #1)
•
Screw upper and hood mounting brackets in tightly.
STEP 9
Installing the glass
•
Place the glass piece over the range hood and tighten
using the 4 designated screws. (See Figure # 2)
Fig #2
— 12 —
STEP 10
Installing the damper
•
Fix the damper on the top vent of hood with 4 screws. (See Figure # 3)
•
If ventilation system is equipped with an external air duct with a
different diameter, apply a reduction fitting. However, for maximum
performance and safety, a 6” round ducting is recommended.
Fig #3
STEP 11
Mount Range Hood Onto Wall
•
Hang the range hood on the hooks of the lower mounting bracket. (See Figure # 4)
•
Screw the range hood to the wall. (See Figure # 5)
CAUTION - Make certain the range hood is secure before releasing!
Fig #4
Fig #5
STEP 12
Connect Ductwork
•
Attach ductwork to damper. Secure the ductwork with duct tape to make sure joints are secure and air-­tight.
•
Do not install the duct tape too tightly as this may prevent the damper flaps from opening which will overwork the motor
and cause improper functioning of the unit.
•
Fasten all connections with sheet metal screws and tape all joints with certified aluminum or foil tape. Use caulking to
seal exterior wall or roof opening around the cap.
— 13 —
Installation
STEP 13
Install Chimney
•
Place chimney on top of the main housing.
•
Remove the protective coating from the upper
chimney. Carefully slide the upper chimney down
into the lower chimney.
•
Use 2 screws to fix the two chimneys together
with the lower chimney bracket, make sure upper
chimney is moving freely. (See Figure #6)
•
Screw the upper chimney to the upper mounting
bracket. (See Figure # 7)
Inner Chimney Bracket
Fig #6
Fig #7
STEP 14
Connect to AC
•
Connect AC plug into a grounded AC outlet having 120V, 60Hz. Place the outlet at a maximum distance of 33-1/2 in.
(851 mm) from where the cord exits on the hood.
•
SEE IMPORTANT INSTRUCTIONS ON THIS PAGE.
3-Pronged Plug
Ground Plug
3-Prong Receptacle
IMPORTANT:
• Observe all governing codes and ordinances.
• It is the customer’s responsibility to contact a qualified electrical installer.
• If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that
the ground path is adequate. A 120-Volt, 60 Hz, AC-only, fused electrical supply is required on a separate 15-amp
circuit, fused on both sides of the line.
• DO NOT ground to a gas pipe.
• Check with a qualified electrician if you are not sure that the range hood is properly grounded.
• DO NOT have a fuse in the neutral or ground circuit.
IMPORTANT: Save this Installation Guide for electrical inspector’s use.
GROUNDING INSTRUCTIONS:
• This appliance must be grounded. In the event of an electrical short-circuit, grounding reduces the risk of electric
shock by providing an escape wire for the electric current.
• This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged
into an outlet that is properly installed and grounded.
WARNING: Improper grounding can result in a risk of electric shock.
• Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to
whether the appliance is properly grounded. DO NOT use an extension cord. If the power supply cord is too short,
have a qualified electrician install an outlet near the appliance.
— 14 —
Installation
STEP 15
Install Filters
To install filters follow these four steps (See Figure # 8):
•
Angle the filter into slots at the back of the hood.
•
Push the button on handle of the filter.
•
Release the handle once the filter fits into a resting position.
•
Repeat to install all filters.
Fig #8
Cleaning Filters
IMPORTANT: Drain oil from baffles, spacers, filters, oil tunnels, oil containers before oil and residue overflow!
•
Remove all baffles, spacers, filters, grease tray, and oil containers and discard oil and residue.
•
Wash with warm soapy water. NOTE: Stainless steel baffles, spacers and oil tunnel are top rack dishwasher safe.
•
Dry thoroughly before replacing and follow directions for installation in reverse.
•
Filters should be cleaned after every 30 hours of use.
•
Should filters wear out due to age and prolonged use, replace with a new filter.
— 15 —
Operation
3 minute delay
On /
Speed Up
LCD
Power Settings
Press the button + once and the motor starts to
operate at Low speed.
u
Press the button + again and the motor will reach
Medium speed.
v
Press the button + once more and the motor will
reach High speed.
w
Press the button - to lower speeds in succession until
the motor stops working (power off).
x
Timer Function
The control module provides the option to run the
motor for a predetermined time period in order to
evacuate remaining vapors from the kitchen.
u
Press the timer button while the motor is
running. The motor will shut off automatically after 3
minutes.
v
Lights
Press the light button
off.
u
to turn LED lights on and
— 16 —
Off /
Slow down
Light
Maintenance
Replacing the Light Bulbs
IMPORTANT:
ALWAYS SWITCH OFF THE ELECTRICITY SUPPLY AT THE MAIN PANEL BEFORE CARRYING OUT ANY OPERATION
ON THE APPLIANCE.
Make sure the range hood is unplugged or turn OFF
breaker.
x
Open the filter and find the spring of the light.
y
u
Replace with a 4 Volt, 2.5 Watt max, LED lights. Do
not touch replacement bulb with bare hands!
Turn ON breaker and range hood to test for
operation.
v
w
Push the spring and the lights will slip out.
CAUTION: BULB MAY BE HOT, PLEASE TAKE OUT
THE BULB WHEN THE BULB IS COMPLETELY
COOL!
— 17 —
Range Hood Assembly
Number
1
2
— 18 —
Part
LED light puck
Decorative filter
3
Panel
4
Rubber
5
Rubber strip
6
Blower
7
Switch wire
8
Switch bracket
9
10
Switch box
Switch
11
Switch panel
12
13
Glass
Housing set
14
Hook
15
Outlet
16
Power cord
17
Electrical box base
18
PCB
19
Capacitor
20
Electrical box cover
21
Outer chimney
22
Inner chimney
23
Outer chimney bracket
24
Inner chimney bracket
Assembly
Circuit Diagram
Blower Assembly
Number
1
2
Part
Blower
Wind Wheel Nut
3
Wind Wheel
4
Motor
5
Incabloc Rubber
6
Aluminum Cover
7
Plastic Wind Net
8
Sealing Gasket
Electrical Assembly
Number
1
2
Part
Electrical Box Base
PCB
3
Capacitor
4
Electrical box cover
5
Switch box
6
Switch
— 19 —
Use and Care Information
Operations
•
Read and understand all instructions and warnings in this manual before operating the appliance. Save these
instructions for future reference.
•
Always leave safety grills and filters in place. Without these components, operating fans could catch on to hair, fingers
and loose clothing.
•
NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into fans.
•
NEVER leave cooking unattended. When frying, oil in the pan can easily overheat and catch fire. The risk of self
combustion is higher when the oil has been used several times.
•
NEVER cook on “open” flames under the range hood. Check deep-fryers during use; superheated oil may be
flammable.
Cleaning
•
The saturation of greasy residue in the fan and filters may cause increased inflammability. Keep unit clean and free of
grease and residue build-up at all times to prevent possible fires.
•
Filters must be cleaned periodically and free from accumulation of cooking residue (see Cleaning Instructions below).
Old and worn filters must be replaced immediately.
•
DO NOT operate fans when filters are removed. Never disassemble parts to clean without proper instructions.
Disassembly is recommended to be performed by qualified personnel only. Read and understand all instructions and
warnings in this manual before proceeding.
SAFETY WARNING: Never put your hand into area housing the fan while the fan is operating!
For optimal operation, clean range hood and all baffle/spacer/filter/grease tray/oil container regularly. Regular care
will help preserve the appearance of the range hood.
Cleaning Exterior Surfaces
•
Clean periodically with hot soapy water and clean cotton cloth. DO NOT use corrosive or abrasive detergent (e.g. Comet
Power Scrub®, EZ-Off® oven cleaner), or steel wool/scoring pads, which will scratch and damage the stainless steel
surface. For heavier soil use liquid degrease such as “Formula 409®” or “Fantastic®” brand cleaner.
•
If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of the hood. Avoid getting
cleaning solution onto or into the control panel. Follow directions of the stainless steel cleaner. CAUTION: DO NOT
leave on too long as this may cause damage to hood finish. Use soft towel to wipe off the cleaning solution, gently
rub off any stubborn spots. Use dry soft towel to dry the hood.
•
After cleaning, you may use non abrasive stainless steel polish such as 3M® or ZEP®, to polish and buff out the
stainless luster and grain. Always scrub lightly, with clean cotton cloth, and with the grain.
•
DO NOT allow deposits to accumulate or remain on the hood.
•
DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting.
•
DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel
for extended periods. Many of these compounds contain chemicals, which may be harmful.
•
Rinse with water after exposure to these compounds and wipe dry with a clean cloth.
— 20 —
Please register your product warranty by visiting the Ancona Home website.
Canada & USA
Phone: 1-800-350-4562
Fax: 800-350-8563
Email: service@anconahome.com
Website: www.anconahome.com
Ancona is in association with Mr Appliance for all after sales service calls.
Please contact their service provider or visit their website:
Phone: 1-888-998-2011
Website: www.mrappliance.com
MAAN1503-EN-01
© 2017 Copyright of Ancona Home. All rights reserved. This material may not be reproduced, displayed, modified or distributed.
— 21 —