Professional SLIM
STEAM POCKET® MOP
S3455UKJR
OWNER’S GUIDE
IMPORTANT SAFETY INSTRUCTIONS
Fsr Hsusehsld Use Only
WHEN USING YOUR SHARK®
STEAM MOP, BASIC SAFETY
PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS
BEFORE USING YOUR
STEAM MOP.
DANGER OF SCALDING.
Please use caution when
using the steam mop. The steam
emitted from the steam mop is
very hot.
IMPORTANT:
This appliance is not intended
for use by persons (including
children) with reduced physical,
sensory or mental capabilities
or lack of experience and
knowledge unless they have
been given supervision or
instruction concerning use
of the appliance by a person
responsible for their safety.
Children should be supervised to
ensure that they do not play with
the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY:
1.
Use the system only for its intended
use.
2. DO NOT use outdoors.
3. DO NOT leave the appliance
unattended when plugged in.
Always unplug the power cord from
the electrical outlet when not in use
and before servicing.
4. DO NOT allow the appliance to be
used by children. Close attention
is necessary when used by or near
children, pets or plants.
5. Children should be supervised to
ensure that they do not play with the
appliance.
6. Use only as described in this manual.
7 . Use only manufacturer’s
recommended accessories.
8. DO NOT operate the appliance with
a damaged plug or cord, or if the
unit has been dropped or damaged.
To avoid the risk of electric shock,
do not disassemble or attempt to
repair the appliance on your own. If
the supply cord is damaged, it must
be replaced by a qualified electrician
in order to avoid a hazard. Incorrect
re-assembly or repair can cause a
risk of electrical shock or injury to
persons when the appliance is used.
9. To protect against a risk of electric
shock, DO NOT immerse the steam
mop into water or any other liquids.
10. DO NOT handle plug or steam mop
with wet hands or operate appliance
without shoes.
11. DO NOT pull or carry by power cord,
use power cord as handle, close a
door on the power cord, or pull the
power cord around sharp edges or
corners. Keep power cord away from
heated surfaces.
www.sharkclean.co.uk
12. DO NOT unplug by pulling on
power cord. To unplug, grasp the
plug not the power cord. Do not
use extension cords or outlets
with inadequate current carrying
capacity.
13. DO NOT put any objects into
openings. Do not use with any
opening that is blocked.
14. DO NOT put hands or feet under the
steam mop. Unit gets very hot.
15. Use ONLY on flat, horizontal
surfaces. Do not use on walls,
counters or windows.
16. DO NOT use on leather, wax polished
furniture or floors, synthetic fabrics,
velvet or other delicate, steam
sensitive materials.
17. Liquid or steam must not be directed
towards equipment containing
electrical components, such as the
interior of ovens.
18. DO NOT add cleaning solutions,
scented perfumes, oils or any other
chemicals to the water used in this
appliance as this may damage the
unit or make it unsafe for use. If
you live in a hard water area, we
recommend using distilled water in
your steam mop.
19. When in use, NEVER turn the
appliance over or on its side. NEVER
DIRECT STEAM TOWARDS PEOPLE,
ANIMALS OR PLANTS.
20. NEVER LEAVE THE STEAM MOP IN
ONE SPOT ON ANY SURFACE FOR
ANY PERIOD OF TIME WITH THE
CLEANING POCKET ATTACHED
AS THIS WILL DAMAGE YOUR
FLOORS.
21. Carefully remove the cleaning
pocket immediately after you have
unplugged and allowed the steam
mop to cool.
22. When cleaning the steam mop,
unplug the power cord from the
electrical outlet and clean with a dry
or damp cloth. Do not pour water or
use alcohol, benzene or paint thinner
on the unit.
23. Extreme caution should be
exercised when using this appliance
to clean stairs.
24. Never use steam mop without a
cleaning pocket attached.
25. Keep your work area well lit.
26. Store steam mop indoors in a cool,
dry place.
27. To avoid circuit overload, do not
operate another appliance on the
same socket (circuit) as the steam
cleaner.
28. If an extension cord is absolutely
necessary, an extension cord rated
a minimum of 15 ampere, 14 gage
cord should be used. Cords rated for
less amperage may overheat. Care
should be taken to arrange cord so
that it cannot be pulled or tripped
over.
29. DO NOT leave unattended when
the system is connected to a power
supply or electrical outlet. Turn off
all controls before unplugging the
unit.
30. DO NOT store unit with damp or wet
cleaning pocket attached. Never
leave the steam mop in one spot on
any surface for any period of time
with a damp or wet cleaning pocket
attached as this will damage your
floors
31. Always unplug and allow the steam
mop to cool before removing or
changing mop heads.
32. Make sure that the water tank door
closed when using the appliance.
WARNING: Your steam mop is
designed to clean hard floor surfaces
that will withstand high heat. Do not
use on unsealed wood or unglazed
ceramic floors. On surfaces that
have been treated with wax or some
no wax floors, the sheen may be
removed by the heat and steam
action. It is always recommended to
test an isolated area of the surface to
be cleaned before proceeding. We
also recommend that you check the
use and care instructions from the
floor manufacturer.
SAVE THESE
INSTRUCTIONS
www.sharkclean.co.uk
This appliance complies with the WEEE-Directive 2002/96/EC on the disposal of
electrical and electronic equipment (WEEE).
This appliance complies with the European directives for electromagnetic
compatibility (EMC) 2004/108/EC and its revisions, as well as Low Voltage
Directive (LVD) 2006/95/EC and its revisions.
This marking indicates that this product should not be disposed
with other household wastes throughout the EU. To prevent possible
harm to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse of
material sources. To return your used device, please use the return
and collection systems or contact the retailer where this product was
purchased. They can take this product for environmental safe recycling.
This product has no on/off switch and operates when plugged into the main supply
source. Disconnect the plug from mains after use.
Although the product is not provided with standby mode or off mode, it still fulfills
the requirements of 1275/2008/EC - the directive for Eco-Design requirements
since according to technical justification, it is considered as inappropriate to
provide standby and off modes when connecting to mains. To reduce energy
consumption be sure to unplug the unit after use.
Guarantee: This product is unconditionally guaranteed for one year against all
defects of workmanship and materials. This guarantee does not affect your
statutory rights. If this product proves unsatisfactory please contact our customer
service department on freephone 0800 781 7831.
This manual covers model:
S3455UKJR 11
TECHNICAL SPECIFICATIONS
Voltage:
220-240V~, 50/60Hz.
Power:
1550 Watts
Water Capacity: 300 ml
www.sharkclean.co.uk
Nst ts be dispssed
sf with sther
hsusehsld waste.
IPX4
Csntents
Thank you
for purchasing
the Shark®
Professional SLIM
Steam Pocket®
Mop.
Getting Started ......................................................................2
Using Your Steam Mop .......................................................5
Care of Your Steam Mop ....................................................8
Troubleshooting Guide .......................................................10
www.sharkclean.co.uk
1
Getting Started
When assembling your steam mop
there may be a little water in or around
the water tank. This is because we test
all our steam mops 100% before you
buy them, so you get a quality Shark ®
Professional SLIM Steam Pocket® Mop.
g
h
a
d
b
i
j
c
e
k
f
a Steam Mop Body
g Quick Release Swivel Cord Wrap
b Mop Handle
h Cord Clip
c All-Purpose Mop Head (1)
i Water Tank
d Filling Flask
e Two-Sided All Purpose Cleaning
Pockets for the All-Purpose Mop
Head (2)
f (1) 6mm x 52mm Large Screw*
*Phillips or flat head screwdriver can be
used. Screwdriver not included.
2
www.sharkclean.co.uk
j STEAM CONTROL Button
k Mop Head Release Button
fig. 1
IMPORTANT: Always make sure the
mop is UNPLUGGED from the wall
when not in use. Never fill the mop,
attach the mop head, change or
remove the cleaning pocket when
the mop is plugged into the wall.
To prolong the life of your Shark ®
Professional SLIM Steam Pocket®
Mop, we recommend using distilled
water. Make sure you only add water
to the tank. Chemicals or cleaning
solution may damage the appliance
and could be unsafe for you and your
family.
1
ASSEMBLE
Insert the Mop handle end labeled
“Front” into the steam mop body.
Make sure it is inserted past the
line printed on the pole. Secure the
assembled handle and pole by using
the large screw and a Phillips or a flat
head screwdriver (screwdriver not
included). (fig. 1)
www.sharkclean.co.uk
3
Getting Started - csnt’d
fig. 2
fig. 4
fig. 5
fig. 3
2
Use the lavender loop on the side of
the cleaning pocket to slide the mop
head into the cleaning pocket. Then
secure the quick fasteners on the top
of the pocket to lock in place. (fig. 2)
3
Snap the mop head into the base to
secure it. (fig. 3)
4 Open the water tank door. (fig. 4)
Use the filling flask and pour water
into the tank. Do not overfill. Press
the water tank door firmly to close.
(fig. 5)
4
www.sharkclean.co.uk
IMPORTANT: Do not use on unsealed
wood or unglazed ceramic floors.
On surfaces that have been treated
with wax or some no wax floors,
the sheen may be removed by
the heat and steam action. It is
always recommended to test an
isolated area of the surface to be
cleaned before proceeding. We
recommend that you check the use
and care instructions from the floor
manufacturer.
Using Ysur Steam Msp
IMPORTANT: Do not use the mop
without attaching a cleaning pocket
and adding water to the tank first.
When you are using the mop for
the first time, it might take longer
than the normal 30 seconds to start
steaming.
st
ea
m
l
ro
nt
co
fig. 7
fig. 6
IMPORTANT: Sweep or vacuum your
floors prior to cleaning with your
Steam Mop.
1
Pull and twist the quick release cord
holder to unwrap the power cord
completely. Plug into an electrical
outlet. (fig. 6)
2
The SBEAM CONBROL button will
flash blue. If the light does not turn
on, reference the troubleshooting
section on page 10. (fig. 7)
www.sharkclean.co.uk
5
Using Ysur Steam Msp - csnt’d
m
ea
st
l
ro
nt
co
fig. 8
Press the SBEAM CONBROL button
once to activate the LOW steam
setting.
3
Press the SBEAM CONBROL button
twice to activate the HIGH steam
setting.(fig. 8)
4 Clean your floors with a forward and
backward motion. (fig. 9)
To stop the steam, press the SBEAM
CONBROL button a third time.
The SBEAM CONBROL button will
flash blue to indicate the mop is in
SBANDBY mode.
6
www.sharkclean.co.uk
fig. 9
fig. 10
5 When one side of the cleaning
pocket gets dirty, just flip the mop
over and you can quickly start using
the other side. (fig. 10)
6 When the water tank is empty, the
steam mop will stop producing
steam. You can refill the water
tank at any time as long as the
mop is unplugged from the outlet.
Reference the filling instructions
from page 4.
NOTE: Please wait 2-3 minutes
for the Steam Mop to cool off
before removing the mop head or
the cleaning pocket. Never leave
the steam mop with a damp/wet
cleaning pocket on any floor.
www.sharkclean.co.uk
7
Care sf Ysur Steam Msp
fig. 11
fig. 13
fig. 12
AFTER USE AND STORAGE
When you have finished using
the steam mop, press the SBEAM
CONBROL button until the LED light
turns flashing BLUE. This stops the
unit from steaming. Unplug the cord
from the outlet and place the mop
into the upright position. Let the unit
cool for 2-3 minutes.
1
Remove the cleaning pocket by
releasing the quick fasteners and
using the lavender loop on the side
of the pocket, avoiding contact with
the hot pad or dirt. (fig. 11)
8
www.sharkclean.co.uk
2
Empty the water tank before storage.
Open the water tank door and empty
the tank over a sink. Close the water
cap. (fig. 12)
3 To store the Shark ® Professional SLIM
Steam Pocket® Mop hanging up, first
remove the head (after it has cooled
and the steam has been released)
then hang on a large hook. (fig. 13)
fig. 16
40°
DECALCIFYING YOUR STEAM MOP
Calcium and mineral deposits can
build up and impact the performance
of your steam mop over time.
fig. 14
fig. 15
CARE OF YOUR ALL PURPOSE
CLEANING POCKET
1 We recommend washing your
cleaning pocket separately from
other fabrics to avoid picking up
lint. Only use liquid detergent (no
powder detergent). Do not use any
fabric softeners or bleach. Line dry.
Do not tumble dry. (fig. 14)
2 If there are loose threads on the
cleaning pocket carefully cut the
thread with scissors. Do not pull on
them or cut at the base. (fig. 15)
ORDERING REPLACEMENT PARTS
To order additional parts and
accessories, feel free to contact us at
JML, Unit 1 Eastside
Port of Tyne
South Shields
NE33 5SP
info@JMLgroup.co.uk
Freephone 0800 781 7831
CLEANING THE NOZZLE
Your steam mop should not normally
require cleaning, however, should
you notice a decrease in the steam
output, it may be necessary to
remove mineral deposits built up
around the nozzle.
1 Unplug the steam mop from the
electrical outlet.
2 Use a small diameter stiff metal
wire, such as a straightened metal
paperclip, and carefully insert the
end of the wire into the nozzle
orifice. (fig. 16)
3 Move the wire back and forth several
times to remove any deposits.
4 Plug the steam mop in to the power
outlet and test steam output.
PART
PART NO.
1 2 All Purpose Pockets
2 Carpet Glider
XT3901UKJR
XCG3450UKJR
www.sharkclean.co.uk
9
Trsubleshssting Guide
PROBLEM
The Professional SLIM
Steam Pocket® Mop
will not turn-on.
The unit will not
make steam.
Cannot select steam
setting/flashing blue
light remains on.
The Professional SLIM
Steam Pocket® Mop
leaves water on the
floor.
The Professional SLIM
Steam Pocket® Mop
left a white spot on
the floor.
POSSIBLE REASONS & SOLUTIONS
Your steam mop should be securely plugged into an electrical
outlet only.
Check your fuse or breaker.
If your unit still does not work, give us a call at:
Freephsne 0800 781 7831.
Is there water in the water tank? If not, add water to your steam
mop following instructions on page 4.
If the unit still doesn’t make steam, follow the decalcification
instructions on page 9.
If you have already plugged in your unit, unplug and try a
different outlet. This may reset the Standby mode.
Add water to the tank and press the SBEAM CONBROL button
to select a steam setting.
If your unit still does not work, call 0800 781 7831.
Check to see if your cleaning pocket is soaked through. We
recommend you unplug the steam mop and change the
cleaning pocket.
Make sure the cleaning pocket is attached correctly.
Do not leave your steam mop on the floor with a damp or wet
cleaning pad.
If you’re using tap water we recommend switching to
distilled water.
Make sure the cap is securely on the water tank.
The pad might be dirty, change the pad.
If you washed the cleaning pad with powder detergent, then it
might be ruined.
Floors are cloudy,
streaky or spotty
after steaming.
The Professional SLIM
Steam Pocket® Mop is
hard to push.
10
www.sharkclean.co.uk
You might have left the mop in the same spot for too long. Do
you have hard water? If you do, you might want to switch to
distilled water.
This might be leftover from past cleaners used on the floor
surface. Use the steam mop a few more times and see if the
leftover cloudiness is removed. If this does not work, we suggest
rinsing the floor with water, letting it dry, and then steam
mopping again with a clean pad. One or more rinses generally
removes the residue. A more stubborn case may require you
to rinse the floor with a mix of one part vinegar and two parts
water.
Make sure the cleaning pocket is attached correctly.
Check to see if the cleaning pad is excessively dirty. Replace if
the cleaning pad is too dirty or wet.
Notes
www.sharkclean.co.uk
11
JML, Unit 1 Eastside
Port of Tyne
South Shields
NE33 5SP
info@JMLgroup.co.uk
Freephone 0800 781 7831
www.sharkclean.co.uk
Registered address: JML House, NW5 3EG
Technical Details
Model number: S3455UKJR 11
Input: 1550 Watts
Main unit voltage: 220-240V~, 50/60Hz
Printed in China
Illustrations may differ from actual product.
S3455UKJR.E.130212.4
Nst ts be dispssed
sf with sther
hsusehsld waste.
IPX4