311396C, ProMix Auto Color and Catalyst Change Kits

Installation - Parts
ProMix™ Auto
Color and Catalyst Change Kits
311396C
For proportional mixing of plural component coatings. For professional use only.
See page 2 for kit information.
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
Wall Mount Fluid Panel
EN
Related Manuals
Contents
Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . .
Kit Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before Servicing . . . . . . . . . . . . . . . . . . . . . . . . .
After Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pressure Relief Procedure . . . . . . . . . . . . . . . . . . .
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
3
5
5
5
6
7
Wall Mount Fluid Panel . . . . . . . . . . . . . . . . . . . . . . 8
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Parts - Wall Mount Fluid Panel . . . . . . . . . . . . . 12
RoboMix II Fluid Panel . . . . . . . . . . . . . . . . . . . . . . 13
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Parts - RoboMix II Fluid Panel . . . . . . . . . . . . . . 16
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 18
Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 18
Related Manuals
Component Manuals in U.S. English
Manual
Description
311079
311189
310654
310655
308778
ProMix Auto Operation
ProMix Auto Service - Parts
Fluid Mix Manifold
Dispense Valve
G3000, G250, G3000HR, G250HR Flow
Meter
Coriolis Flow Meter
Color Change Valve Assembly,
Low Pressure
Color Change Valve, Low Pressure
Color Change Valve Assembly, High
Pressure
Color Change Valve, High Pressure
310696
312783
312782
312783
312782
311191
ProMix Auto™ Web Communications
Software
Kit Information
Wall Mount Color/Catalyst Change Kits:
RoboMix II Color/Catalyst Change Kits:
Kit 249973, 2 color/catalyst change
Kit 249970, 2 color/catalyst change
Kit 249974, 4 color/catalyst change
Kit 249971, 4 color/catalyst change
Kit 249975, 7 color/catalyst change
Kit 249972, 7 color/catalyst change
2
311396C
Warnings
Warnings
The following general warnings are for the setup, use, grounding, maintenance, and repair of this equipment. Additional, more specific warnings may be found throughout the body of this manual where applicable. Symbols appearing in the body of the manual refer to these general warnings. When these symbols appear throughout the manual,
refer back to these pages for a description of the specific hazard.
WARNING
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion:
•
•
•
•
Use equipment only in well ventilated area.
Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic
drop cloths (potential static arc).
Keep work area free of debris, including solvent, rags and gasoline.
Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes
are present.
•
Ground all equipment in the work area. See Grounding instructions.
•
Use only grounded hoses.
•
Hold gun firmly to side of grounded pail when triggering into pail.
•
•
If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment
until you identify and correct the problem.
Keep a fire extinguisher in the work area.
INTRINSIC SAFETY
Only models with a G3000 or G3000HR for both A and B meters are approved for installation in a Hazardous Location - Class I, Div I, Group D, T2 C. To help prevent fire and explosion:
• Do not install equipment approved only for non-hazardous location in a hazardous area. See the ID
label for the intrinsic safety rating for your model. Refer to instruction manuals for your model.
•
Do not substitute system components as this may impair intrinsic safety.
ELECTRIC SHOCK HAZARD
Improper grounding, setup, or usage of the system can cause electric shock.
•
•
•
Turn off and disconnect power at main switch before disconnecting any cables and before servicing
equipment.
Connect only to grounded power source.
All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations.
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like
just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.
•
Do not point gun at anyone or at any part of the body.
•
Do not put your hand over the spray tip.
•
Do not stop or deflect leaks with your hand, body, glove, or rag.
•
311396C
Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,
checking, or servicing equipment.
3
Warnings
WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
•
Do not operate the unit when fatigued or under the influence of drugs or alcohol.
•
Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.
•
Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information
about your material, request MSDS forms from distributor or retailer.
•
Check equipment daily. Repair or replace worn or damaged parts immediately with genuine Graco
replacement parts only.
•
Do not alter or modify equipment.
•
Use equipment only for its intended purpose. Call your Graco distributor for information.
•
Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
•
Do not kink or over bend hoses or use hoses to pull equipment.
•
Keep children and animals away from work area.
•
Comply with all applicable safety regulations.
MOVING PARTS HAZARD
Moving parts can pinch or amputate fingers and other body parts.
•
Keep clear of moving parts.
•
Do not operate equipment with protective guards or covers removed.
•
Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
•
Read MSDS’s to know the specific hazards of the fluids you are using.
•
Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic
fumes, burns, and hearing loss. This equipment includes but is not limited to:
4
•
Protective eyewear
•
Clothing and respirator as recommended by the fluid and solvent manufacturer
•
Gloves
•
Hearing protection
311396C
Service
Service
Before Servicing
4. Shut off ProMix™ Auto power (0 position). FIG. 1.
5. If servicing EasyKey™ Display, also shut off power
at main circuit breaker.
0 = OFF
•
Servicing EasyKey™ display exposes you to
high voltage. Shut off power at main circuit
breaker before opening enclosure.
•
Do not substitute system components as this
may impair intrinsic safety.
FIG. 1: Power Switch
1. Follow “Pressure Relief Procedure” on page 6.
After Servicing
2. Follow “Shutdown” on page 7 if service time will
exceed pot life time and before servicing fluid components.
After servicing the system, be sure to follow the
Start Up checklist and procedure in the ProMix™ Auto
Operation manual 311079.
3. Close main air shutoff valve on air supply line and
on ProMix™ Auto.
311396C
5
Pressure Relief Procedure
Pressure Relief Procedure
1. While in Mix mode (dispensing mix material), isolate
the A and B fluid supply.
2. Push the manual override on the A and B dispense
valve solenoids to relieve pressure. FIG. 2 (Wall
Mount Fluid Supply) and FIG. 3 (RoboMix II Fluid
Supply).
If Dose alarm occurs, clear alarm.
3. Purge mix material following the Purging section in
the ProMix™ Auto Operation Manual (311079).
Solenoid
Button
4. Isolate the solvent fluid supply.
5. Initiate purge sequence following the Purging section in the ProMix™ Auto Operation Manual
(311079).
6. Verify the solvent pressure is reduced to 0.
If Purge Volume alarm occurs, clear alarm.
FIG. 3: RoboMix II Fluid Supply Solenoids
Solenoid
Button
FIG. 2: Wall Mount Fluid Supply Solenoids
6
311396C
Shutdown
Shutdown
4. If servicing EasyKey™ Display, also shut off power
at main circuit breaker.
0 = OFF
•
Servicing EasyKey™ display exposes you to
high voltage. Shut off power at main circuit
breaker before opening enclosure.
•
Do not substitute system components as this
may impair intrinsic safety.
Service Shutdown
1. Follow “Pressure Relief Procedure” on page 6.
FIG. 4: Power Switch
2. Close main air shutoff valve on air supply line and
on ProMix™ Auto.
3. Shut off ProMix™ Auto power (0 position). FIG. 4.
311396C
7
Wall Mount Fluid Panel
Wall Mount Fluid Panel
Installation
See illustrations and “Parts - Wall Mount Fluid Panel” on
page 12 for component kit parts and referenced numbers throughout this procedure.
2. Remove plug on dosing valve. Replace with 90° fitting (5) to either color change dosing valve or catalyst change dosing valve. (See FIG. 6.)
90°
Fitting
Apply pipe sealant to all tapered threads when
installing kit. Do not apply sealant to swivel fittings.
1. Follow “Pressure Relief Procedure” on page 6.
2. Determine if you are installing color change or catalyst change.
If
If installing catalyst change dump valve, follow
same procedure for color side of Wall Mount Fluid
Panel.
Mount Dump Valve
Dump valve bracket mounts in same holes with same
hardware as manifold bracket.
1. Remove manifold from mounting plate. Place dump
valve bracket (7) in place and reinstall manifold
bracket. Dump valve bracket (7) will be installed
between plate and manifold bracket. (See FIG. 5.)
FIG. 6: Install 90° Fitting
3. Mount dump valve (12) to bracket (7) (use screw
(16) provided) from side of dispense valve air piston/cylinder. (See FIG. 7.)
4. Mount 90° fitting (5) into inlet of dump valve. (See
FIG. 6.)
FIG. 7: Mount Dump Valve to Bracket
FIG. 5: Mount Dump Valve Bracket
5. Connect fluid hose (10) from dosing valve to dump
valve.
Mount Solenoid Valve
8
Solenoid valve mounts into existing manifold.
311396C
Wall Mount Fluid Panel
1. Remove blank plate from position 5 for color change
or position 6 for catalyst change. (See FIG. 8.)
•
For catalyst change, wire solenoid valve into port J9,
Pin 13, and J9, Pin 14 (red in Pin 13 and black in Pin
14).
6
5
P14
P11 P12
P13
FIG. 8: Install Solenoid Valve
FIG. 9: Wire Solenoid Valve
2. Install solenoid (6) valve using screws provided in
place of blank plate. Verify that solenoid gasket
remains on solenoid. (See FIG. 8.)
3. Wire solenoid valve: (See FIG. 9.)
•
For color change, wire solenoid valve into port J9,
Pin 11 and J9, Pin 12 (red in Pin 11 and black in Pin
12).
Install Fittings
1. Remove electrical panel from mounting panel. To
complete this step, you may need to detach pneumatic tubing and lengthen wiring in electrical panel.
Label pneumatic tubing before detaching from manifold.
2. Remove 2 plugs for each solenoid on outbound side
of manifold. (See FIG. 10.)
Remove 2
pl
plugs per
solenoid,
FIG. 10: Outlet Ports
3. Thread in 1/8 in. NPT pneumatic push fittings (4).
311396C
9
Wall Mount Fluid Panel
4. Connect pneumatic tubing from push fittings (4)
down side of cabinet, through grommet, and to
dump valve (12). (See FIG. 11.)
Install Communication Network (CAN)
Cable
1. Wire CAN cable (9) (with strain relief (3) through
port on left side of electrical box) to J7 connector on
circuit board. (See FIG. 12.)
9
17
FIG. 12: CAN Cable Wiring
FIG. 11: Connect Pneumatic Tubing
2. Follow wiring diagram to connect Ferrules to Phoenix connector (17). See ProMix™ Auto Service and
Repair manual (311189). (See FIG. 12.)
5. Reinstall electrical panel.
3. Connect Phoenix connector (17) to board. (See FIG.
12.)
4. After connection is made, tighten strain relief fitting
(3).
5. Run CAN cable (9) to color change control assembly and connect to CAN input (See FIG. 13).
FIG. 13: CAN Cable
10
311396C
Wall Mount Fluid Panel
6. Provide air supply to main air inlet of color change
control assembly. (Main air inlet should be on bottom of assembly to prevent moisture buildup in manifold solenoid valves.) (See FIG. 14.)
FIG. 14: Air Inlet
7. Route tubing (14) (10 ft. of 5/32 in. tube for each
valve is included in kit) from outlet fitting of each
solenoid in color change control assembly to color
change fluid valve stack (15). (See FIG. 15.)
FIG. 15: Color Stack
Each color change control assembly includes a
solenoid for each color and a solenoid for solvent
flush.
Set Address
Follow procedures for setting address and termination
resistor according to ProMix™ Auto Operation manual
(311079).
311396C
11
Wall Mount Fluid Panel
Parts - Wall Mount Fluid Panel
Kit 249973, 2 color/catalyst change
Kit 249974, 4 color/catalyst change
Kit 249975, 7 color/catalyst change
17
3
15
6
4
7
9
8
11
16
14
12
5
FIG. 16: Wall Mount Fluid Panel Color/Catalyst Change Kit
Ref.
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
12
Ref.
No.
Part No. Description
054754
054757
111987
114263
114342
117356
15G443
15G450
15G612
24N345
249870
287394
590332
TUBE, nylon, rnd, 3 ft. (not shown)
TUBE, nylon, rnd, 3 ft. (not shown)
CONNECTOR, cord, strain relief
FITTING, connector, male
ELBOW, 1/4-18 NPSM
VALVE, solenoid, 12 VDC
BRACKET, valve mount
BRACKET, color change
CABLE, 50 ft.
HOSE, coupled, 1.5 ft. (not shown)
ASSY, control, color/catalyst change
VALVE, dispense
TUBE, poly-flo, 5/32 ID x 1/4 OD, 100
ft. (not shown)
Qty
1
1
1
2
2
1
1
1
1
1
1
1
1
14
Part No. Description
598095
15
16
17
18
256289
256291
256294
C19798
119248
110110
Qty
TUBE, 5/32 OD, nylon
Kit 249973, 30 ft.
Kit 249974, 50 ft.
Kit 249975, 80 ft.
Color/catalyst change valve stack
assy
3 valve assy used in kit 249973
5 valve assy used in kit 249974
8 valve assy used in kit 249975
SCREW, cap, socket head
CONNECTOR, plug, 5 position
SEALANT, pipe, SST (not shown)
-
1
1
1
5
1
1
311396C
RoboMix II Fluid Panel
RoboMix II Fluid Panel
Installation
See illustrations and “Parts - RoboMix II Fluid Panel” on
page 16 for component kit parts and referenced numbers throughout this procedure.
Apply pipe sealant to all tapered threads when
installing kit. Do not apply sealant to swivel fittings.
•
For catalyst change, wire solenoid valve into port J9,
Pin 13, and J9, Pin 14 (red in Pin 13 and black in Pin
14). (See FIG. 9.)
Outlet to
bulkhead
outlet fitting
1. Follow “Pressure Relief Procedure” on page 6.
2. Determine if you are installing color change or catalyst change.
Inlet
Mount Solenoid Valve
1. Remove blank plate from position 5 for color change
or position 6 for catalyst change.
2. Install solenoid valve (3) using screws provided in
place of blank plate. Use position 5 for color change
and position 6 for catalyst change. Verify solenoid
gasket remains on solenoid.
3. Route wiring from solenoid valve through grommet
(D) to board. (See FIG. 17.)
•
For color change, wire solenoid valve into ports J9,
Pin 11 and J9, Pin 12 (red in Pin 11 and black in Pin
12). (See FIG. 9.)
311396C
D
FIG. 17: RoboMix II Dump Valves and Grommet
Mount Dump Valve
1. Remove cap screw plugs from one of two open
positions on RoboMix II fluid panel. Mount dump
valve (13) in that position. Use screws (7) included
with kit to screw dump valve down to RoboMix II
housing assembly. (See FIG. 17.)
2. Mount outlet fitting (10) and inlet fitting (9) into dump
valve (13). (See FIG. 17.)
13
RoboMix II Fluid Panel
Install Fittings
1. Install bulkhead outlet fittings (4) for ports A and B;
tighten nut. (See FIG. 18.)
Install Communication Network (CAN)
Cable
1. Install strain relief fitting (15) into color change or
catalyst change port on back of RoboMix II housing
assembly. (See FIG. 19.)
15
FIG. 18: Outlet Fittings
2. Mount 1/4 in. PTFE tubing (19) (included in kit) into
fittings and tighten fittings:
a. Remove 1/4 in. plug from color dosing valve top
port or catalyst dosing valve top port.
b.
c.
Install fitting (9) from kit into port that plug was
removed from.
Route tubing from dosing valve to dump valve
(13). (See FIG. 17.)
d. Route tubing from dump valve (13) to bulkhead
outlet fitting (4). (See FIG. 17 and FIG. 18.)
FIG. 19: RoboMix II Strain Relief Fitting
2. Route CAN cable (6) through strain relief (15),
through assembly, and through grommet to board.
(See FIG. 19.)
3. Connect CAN cable (6) to J7 connector on board.
4. Follow wiring diagram to connect Ferrules to Phoenix connector. See ProMix™ Auto Service and
Repair manual (311189). (See FIG. 20.)
5. Connect Phoenix connector (16) to board. (See FIG.
20.)
6
16
FIG. 20: Phoenix Connector
14
311396C
RoboMix II Fluid Panel
6. After connection is made, tighten strain relief fitting
(15). (See FIG. 19.)
7. Run CAN cable (6) to color change control assembly (8) and connect to CAN input. (See FIG. 13.)
8. Provide air supply to main air inlet of color change
control assembly using tubing (11). (Main air inlet
should be on bottom of assembly to prevent moisture buildup in manifold solenoid valves.) (See FIG.
14.)
9. Route tubing (12) (10 ft. of 5/32 in. tube for each
valve is included in kit) from outlet fitting of each
solenoid in color change control assembly to color
change fluid valve stack (14). (See FIG. 15.)
Each color change control assembly includes a
solenoid for each color and a solenoid for solvent
flush.
Set Address
Follow procedures for setting address and termination
resistor according to ProMix™ Auto Operation manual
(311079).
311396C
15
RoboMix II Fluid Panel
Parts - RoboMix II Fluid Panel
Kit 249970, 2 color/catalyst change
Kit 249971, 4 color/catalyst change
Kit 249972, 7 color/catalyst change
14
10
5
18
3
6
13
8
15
11
7
4
9
FIG. 21: RoboMix II Fluid Panel Color/Catalyst Change Kit
Ref.
No.
1
2
3
4
5
6
7
8
9
10
11
16
Ref.
No.
Part No. Description
054754
054757
120014
120029
15G450
15G612
15G842
249868
249869
249870
510223
513308
590332
TUBE, nylon, rnd, 1 ft. (not shown)
TUBE, nylon, rnd, 1 ft. (not shown)
VALVE, solenoid, includes item 7
FITTING, bulkhead, compression
BRACKET, color change
CABLE, 50 ft.
FASTNER, SHCS, 1/4-20 x 1.625
ASSY, control, color/catalyst change
2 color, 1 flush
4 color, 1 flush
7 color, 1 flush
FITTING, elbow, male
FITTING, connector
TUBE, poly-flo, 5/32 ID x 1/4 OD
Qty
1
1
1
1
1
1
2
1
1
1
1
2
1
Part No. Description
12
598095
13
14
692022
15
16
949796
220020
220023
111987
119248
17
18
19
110110
110932
597350
Qty
TUBE, 5/32 OD, nylon (not shown)
Kit 249970, 30 ft.
Kit 249971, 50 ft.
Kit 249972, 80 ft.
VALVE, diaphragm, dispense
Color/catalyst change valve stack
assy
3 valve assy used in kit 249970
5 valve assy used in kit 249971
8 valve assy used in kit 249972
CONNECTOR, cord, strain relief
CONNECTOR, plug, 5 position
(not shown)
SEALANT, pipe, SST (not shown)
CONNECTOR, male
TUBE, PTFE, 3/8 OD, 3 ft.
(not shown)
-
1
1
1
1
1
1
1
2
1
311396C
Notes
Notes
311396C
17
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.Graco Information
Graco Information
For the latest information about Graco products, visit www.graco.com.
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 311396
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS, MN 55440-1441 • USA
Copyright 2005, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revised September 2012