TWIN TANK AIR COMPRESSOR 5 GALLON / 3 PEAK

COMPONENT
COMPOSANT
COMPONENTE
#691298
TWIN TANK AIR COMPRESSOR
5 GALLON / 3 PEAK HP
COMPRESOR DE AIRE DE DOBLE TANQUE
5 GALONES (18,93 L) / 3 HP MÁXIMO
(2 237,10 watts)
COMPRESSEUR D’AIR À
RÉSERVOIR DOUBLE
18,9 LITRES (5 GALLONS)
3 HORSE-POWER
DE POINTE
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS
PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT
LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
CE MANUEL CONTIENT DES INFORMATIONS IMPORTANTES CONCERNANT LA SÉCURITÉ, LE FONCTIONNEMENT ET LE
REMISAGE DE CE PRODUIT. LIRE, ÉTUDIER ET VEILLER À BIEN COMPRENDRE TOUTES LES MISES EN GARDE ET INSTRUCTIONS
ET AUTOCOLLANTS APPOSÉS SUR LE PRODUIT AVANT DE L’UTILISER. NE PAS RESPECTER CES INSTRUCTIONS POURRAIT
ENTRAÎNER DES BLESSURES ET/OU DES DOMMAGES MATÉRIELS.
ESTE MANUAL CONTIENE INFORMACIÓN IMPORTANTE SOBRE LA SEGURIDAD, OPERACIÓN, MANTENIMIENTO Y ALMACENAMIENTO DE ESTE PRODUCTO. ANTES DE USARLO, LEA Y COMPRENDA TODAS LAS PRECAUCIONES, ADVERTENCIAS,
INSTRUCCIONES Y ETIQUETAS DEL PRODUCTO. DE LO CONTRARIO PODRÍA SUFRIR LESIONES GRAVES O CAUSAR DAÑOS
MATERIALES.
87-1904-60957
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™
MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
PARA EL SERVICIO
PARA EL CONSUMIDOR
1-800-590-3723
Printed in China
Imprimé dans la Chine
Impreso en China
KAWASAKI™ EST UNE MARQUE DE COMMERCE DE KAWASAKI™
MOTORS CORP., U.S.A., QUI NE FABRIQUE PAS ET NE DISTRIBUE
PAS CE PRODUIT THIS PRODUCT. LES QUESTIONS DES CONSOMMATEURS DOIVENT ÊTRE ADRESSÉES À :
KAWASAKI™ ES UNA MARCA REGISTRADA CON LICENCIA DE
KAWASAKI™ MOTORS CORP., E.U.A., QUE NO FABRICA NI
DISTRIBUYE ESTE PRODUCTO. LAS CONSULTAS DE LOS
CONSUMIDORES DEBEN DIRIGIRSE A:
©COPYRIGHT 2007 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
691298 – Twin Tank Air Compressor, Compresor de aire de doble
tanque, Compresseur d’air à réservoir double_Rev 3/26/07
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT, DO NOT RETURN THIS
PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL,
HAVE THE FOLLOWING INFORMATION AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE A SUGGESTION OR
COMMENT, GIVE US A CALL OR EMAIL US AT: INFO@ALLTRADETOOLS.COM. YOUR FEEDBACK IS VITAL TO US.
POUR TOUTE QUESTION OU EN CAS DE PROBLÈME AVEC LE PRODUIT ALLTRADE, NE PAS LE RETOURNER AU MAGASIN OÙ IL
A ÉTÉ ACHETÉ. APPELER LE SERVICE APRÈS-VENTEAU 1-800-590-3723. AVANT D’APPELER, VEILLER À SE PROCURER LES
INFORMATIONS SUIVANTES : No. DE MODÈLE, DATE DE L’ACHAT ET ADRESSE DU MAGASIN. UN REPRÉSENTANT D’ALLTRADE
PEUT RÉSOUDRE VOTRE PROBLÈME PAR TÉLÉPHONE. POUR TOUT COMMENTAIRE OU SUGGESTION, N’HÉSITEZ PAS À NOUS
APPELER OU NOUS CONTACTER PAR COURRIEL À L’ADRESSE : INFO@ALLTRADETOOLS.COM. VOS COMMENTAIRES NOUS
SONT EXTRÊMEMENT PRÉCIEUX.
SI TIENE DUDAS O SURGEN PROBLEMAS CON SU PRODUCTO ALLTRADE, NO LO DEVUELVA A LA TIENDA LLAME A NUESTRO
DEPARTAMENTO DE SERVICIO AL CLIENTE AL 1-800-590-3723. ANTES DE LLAMAR, TENGA A MANO LA SIGUIENTE
INFORMACIÓN: No. DE MODELO, FECHA DE COMPRA Y DIRECCIÓN DE LA TIENDA. UN REPRESENTANTE DE ALLTRADE PUEDE
RESOLVER SU PROBLEMA POR TELÉFONO. SI DESEA HACER ALGUNA SUGERENCIA O COMENTARIO, LLÁMENOS O ENVÍENOS
UN MENSAJE DE CORREO ELECTRÓNICO A. INFO@ALLTRADETOOLS.COM. SUS COMENTARIOS SON FUNDAMENTALES PARA
NOSOTROS.
TABLE OF CONTENTS
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
SAFETY ALERT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . . .3
UNPACKING & INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
SAFETY WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8
GENERAL SAFETY WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8
INSTALLATION AND LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
GROUNDING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-10
EXTENSION CORDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-11
COMPRESSOR FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-14
ASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-16
OPERATING THE AIR COMPRESSOR . . . . . . . . . . . . . . . . . . . . . . . . . .16-17
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-20
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-25
PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26-30
PARTS DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30-31
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32-35
CONGRATULATIONS!
Thanks for choosing this product. At Alltrade, our aim is to provide you with quality
products at an affordable price, and we want you to be totally satisfied with your
product and our Customer Service. If any help and advice is needed, please
contact us at 1-800-590-3723. Properly cared for, this product will give you many
years of satisfaction.
SPECIFICATIONS
SPECIFICATIONS
Two Pole Induction Motor
Power
Air Delivery
Maximum Pressure
Duty Cycle
3.0 Peak HP / 1.3 Running HP
SPECIFICATIONS
5 Gallon Twin Stack Air Tank
Oil Lubricated Direct Drive Pump
Cast Iron Cylinder
Thermal Overload Protection for Safety
High Flow Regulator for Precision Air Flow Control
Tank and Outlet Pressure Gauges
Dual Quick Connect Coupler
DUTY CYCLE:
This air compressor pump is capable of running continuously. However, in order to prolong the life of your air compressor, it is recommended that a 50% to 75% average duty
cycle be maintained. Duty cycle refers to the percentage of time a compressor can safely run within a given amount of time expressed as a ratio. Example: Oil lubricated compressors are typically rated at a 50% duty cycle, meaning that the compressor motor can
run about 50% of the total time it is being used to supply air to a tool. During the ON time,
the motor is running to pressurize the tank. During the OFF time, the motor is stopped
and the tools are running off on the pressurized air stored in the tank. If your air tools are
draining pressure off of the tank too quickly, the compressor motor must run more than
50% of the time the compressor is in use. This can lead to overheating and will significantly shorten the life of the compressor.
INTRODUCTION
This oil lubricated air compressor is designed for Household Use Only and is not
intended for commercial applications. It is well suited for do-it-yourselfers with a
variety of automotive and home uses.
This instruction manual is intended for your benefit. Please read and follow the safety, installation, maintenance and troubleshooting steps described within to ensure
your safety and satisfaction. The contents of this instruction manual are based upon
the latest product information available at the time of publication. The manufacturer reserves the right to make product changes at any time without notice.
SAFETY ALERT
3400 RPM
115V, 60 Hz, 15 Amps
5.1 SCFM output @ 40 PSI
4.1 SCFM output @ 90 PSI
125 PSI
75%
Read and understand this entire instruction manual
before attempting to assemble, install, operate or maintain this air compressor. Failure to comply with the instructions may result in serious personal injury
and/or property damage!
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
1
2
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS
The safety instructions provided in this manual are not intended to cover all possible
conditions and practices that may occur when operating, maintaining and cleaning
power equipment.
Always use common sense and pay particular attention to all the DANGER,
WARNING, CAUTION and NOTE statements of this manual.
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
Do not operate this air compressor if damaged during
shipment, handling or misuse. Damage may result in bursting, which can
cause serious injury or property damage. All damaged parts must be
repaired or replaced as needed prior to operating this air compressor.
Check to see that all nuts, bolts and fittings are secure before putting this air compressor into service. If you have any questions, or require assistance with damaged
or missing parts, please contact our Consumer Helpline: Phone: 1-800-590-3727
E-Mail: info@alltradetools.com
Please have the serial number, model number, date of purchase, and parts list (with
missing parts identified) available for reference when calling.
MODEL NUMBER:
SERIAL NUMBER:
DATE OF PURCHASE:
SAFETY WARNINGS
READ ALL SAFETY WARNINGS BEFORE USING AIR COMPRESSOR.
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
GENERAL SAFETY WARNINGS
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
Keep work area clean. Messy areas and cluttered workbenches invite personal injury and/or property damage.
NOTE provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
UNPACKING & INSPECTION
After opening the carton, unpack your new air compressor and related parts &
accessories. Please inspect it carefully for any damage that may have occurred during transit. Please check it against the photograph on carton. If any parts are missing, please contact our Consumer Helpline: Phone: 1-800-590-3723 E-Mail:
info@alltradetools.com
Use care when lifting or moving tool. This air compressor is very heavy and could cause injury if handled incorrectly.
3
Keep children and visitors away. All children should be kept away from the
work area. DO NOT let children handle the compressor or extension cord.
Maintain a safe distance for any person near the work area.
Operating any tools or equipment under the influence of drugs, alcohol, or
medication can cause personal injury to yourself and others.
Wear proper apparel. Remove your jewelry before using air compressor. Do
not wear loose clothing, necklaces, rings, bracelets, or other jewelry, which may
get caught in moving parts. Nonskid footwear and electrically non-conductive
gloves are highly suggested while working. Wear protective hair covering to
contain long hair.
Protect your eyes. The operation of any air compressor can result in foreign
objects being thrown into the eyes, which can result in severe eye damage.
Always wear eye protection that meets ANSI Z28.1 specifications during air
compressor operation. Eyeglasses are not always safety glasses.
Be responsible for your hearing. Wear hearing protection during extended
periods of operation.
Use the right tool. Use tools properly and for their intended task. Do not force
a small tool to do the job of a heavy-duty tool. Using the right tool to do the
right job will make doing the job safer.
Check damaged parts before use of any air tools or attachments. A guard or
other part that is damaged should be carefully checked to ensure that it will
operate properly and perform its intended function. Check for misalignment or
binding of moving parts, breakage of parts, mounting, or any other conditions
that may affect tool operation. A guard or other part that is damaged should be
properly replaced. See replacement parts list for additional details.
Avoid unintentional starting. Be sure that your air compressor is in the OFF
position before plugging it into a power cord or electrical receptacle.
Store all maintenance tools away from the immediate area before turning ON
your air compressor.
Do not overreach. Proper footing and balance is a must at all times while using
tools. Unstable support may lead to personal injury. Do not stand on the tool.
Serious injury could result if the tool tips over or you accidentally contact tool.
Never leave the air compressor running unattended. Always turn the power to the
OFF position and do not leave the air compressor until it comes to a complete stop.
When using air accessories, consult the owner’s manual provided by the
manufacturer. The use of improper accessories may cause risk of injury to
yourself and others.
Always make sure the tool is in the OFF position and unplugged from the
electrical receptacle when making adjustments, changing parts, or performing any maintenance.
Secure work. When possible, the use of clamps or a holding device is much
safer than holding the work piece with your hands.
Keep protective guards in place and in proper working condition.
Maintain tools and equipment with care. They will function better and more
safely when kept clean and in good working condition. Keeping the air compressor clean, dry, and free of grime will add to its life and performance.
Childproof the workshop. The use of master switches and padlocks is highly
recommended. Remove starter keys where applicable.
5
Some dust created by spraying, blowing, power sanding, sawing, grinding,
drilling and other construction activities contains chemicals known to the
State of California to cause cancer, birth defects or other reproductive harm.
Reduce your exposure to these chemicals by wearing approved safety equipment such as dust masks that are designed to filter out microscopic particles.
Use of this product will expose you to chemicals known to the State of
California to cause cancer, birth defects, and reproductive harm. AVOID INHALING VAPORS AND DUST. WASH HANDS AFTER USING.
This product contains chemicals, including lead, known to the State of
California to cause cancer, birth defects, and reproductive harm. WASH HANDS
AFTER HANDLING.
Handling the power cord on this product may expose you to lead, a chemical
known to the state of california to cause cancer and birth defects or other
Reproductive harm. WASH HANDS AFTER HANDLING.
DRAIN LIQUID FROM AIR TANK DAILY
• Use the drain valve located on the bottom of the lower air tank to drain. Failure to
properly drain liquid from the tank will cause rust from moisture buildup, which
weakens the tank and could lead to a violent tank explosion. Periodically inspect the
tanks for unsafe conditions such as corrosion, cracked welds, and leaks.
• Release air slowly when draining moisture or depressurizing the air compressor. Fast moving air will stir up dust, dirt and debris that may be harmful.
RISK OF FIRE OR EXPLOSION
Avoid dangerous environments. Do not spray combustible/flammable liquid in
a confined area. Spray area must be well ventilated. Do not smoke while spraying or spray where spark or flame is present. Arcing parts — keep compressor
at least 20’ away from spraying area and all explosive vapors. Do not use compressor near gasoline or other flammable materials. Operate the air compressor in a well-ventilated area. Do not direct paint or other spray material towards
the compressor. Read and follow all safety instructions for the material you are
spraying. Be sure to use an approved respirator designed for use with your specific application.
RISK OF INJURY
Do not direct air stream at body. Use eye protection. Compressor starts automatically. Do not touch MOVING PARTS. Keep guards in place. Compressor
does not supply breathable air.
RISK OF BURSTING
• Do not adjust regulator to result in output pressure greater than marked maximum pressure of attachment. If a regulator has not been installed, use only
attachment rated at 200 PSI or higher. Do not weld on or repair tank — A
DAMAGED TANK MUST BE REPLACED IMMEDIATELY. Do not operate without
proper safety valve in place.
• Never attempt to repair or make modifications to the tank or its attachments.
Welding, drilling, or any other modifications may weaken the tank, which may
result in damage from rupture or explosion. Never remove or attempt to adjust the
pressure switch, safety valve, or other components that control tank pressure.
Never substitute parts or attempt to alter the factory set operating pressures.
RISK OF ELECTRICAL SHOCK
Disconnect air compressor from power source before servicing. USE PROPERLY grounded ELECTRICAL CONNECTIONS — do not use grounding adapters.
Do not use in wet or damp locations or expose to rain. Keep all connections
dry and off the ground. Do not allow power cords to come into contact with
water. Do not touch the plug with wet hands. Do not pull on the electrical cord
to disconnect from the power outlet. Store air compressor indoors when not in
use. Any electrical wiring or repairs performed on this air compressor should
be done by authorized service personnel in accordance with federal and local
electrical codes.
RISK TO BREATHING
• This air compressor is not designed, nor intended for the supply of breathable
quality air. Air produced by this unit may contain carbon monoxide or other
toxic vapors. Do not inhale air from the compressor or from a breathing
device connected to it.
• Operate the air compressor in a well-ventilated area. Read and follow all safety instructions for the material you are spraying. Be sure to use an approved
respirator designed for use with your specific application.
RISK OF BURNS
Touching exposed metal such as the compressor head or exhaust tube can
result in serious burns. Keep hands and fingers away from exposed metal parts
on air compressor during or immediately after operation. Air compressors generate significant heat during normal operation and will remain hot for some time
after use. Do not reach around protective shrouds or attempt any maintenance
until compressor has been allowed to cool.
RISK OF FLYING OBJECTS
Do not direct compressed air stream at people or pets. The powerful compressed air stream can damage exposed skin and easily propel loose dirt and
other small objects at high-speed, resulting in serious injury. Always wear eye
protection that meets ANSI Z28.1 specifications. Use only OSHA approved air
blowguns. Never leave a pressurized air compressor unattended. Shut OFF air
compressor and relieve pressure before performing maintenance or repairs. Do
not move the air compressor while the air tank is pressurized. Never attempt to
move the air compressor by pulling on the air hose.
RISK OF FALLING
Portable air compressors can fall from a table, workbench, or roof causing
damage to the compressor and could result in serious injury or death to the
operator. Always operate air compressor in a stable and secure position to prevent accidental movement of the unit. Never operate air compressor on a roof
or other elevated position. Use additional air hose to reach high locations.
RISK OF PROPERTY DAMAGE WHEN TRANSPORTING COMPRESSOR
Oil can leak or spill and could result in fire or breathing hazard, serious injury or
death. Oil leaks will damage carpet, paint, or other surfaces in vehicles or trailers.
AIR TOOLS AND ACCESSORIES
Do not exceed the pressure rating of any air tools, spray guns, air accessories,
or inflatables. Excess pressure can cause them to explode, resulting in serious
injury. Follow the manufacturers recommended pressure settings for all air
tools and air accessories.
INSTALLATION AND LOCATION
In order to avoid damaging the air compressor, do not allow the unit to be tilted more than 10º from the normal horizontal position when operating.
The compressor must be run with the rubber feet resting on a flat and stable
horizontal surface.
The air compressor must be used in a clean and well-ventilated area. The compressor requires an unobstructed airflow and must be located a minimum of 20
inches from any walls or other obstructions that may prevent proper ventilation.
8
DO NOT place air compressor in an area:
Improper installation of the grounding plug can result in a risk of electric
shock. If repair or replacement of the cord is necessary, do not connect the
grounding wire to either flat blade terminal. The wire with GREEN insulation
with or without yellow stripes is the grounding wire.
• Where there is evidence of oil or gas leaks.
• Where flammable gas vapors or materials may be present.
• Where air temperatures fall below 32ºF or exceed 104ºF.
• Where extremely dirty air or water could be drawn into the air compressor.
Serious injury or death may occur if electrical sparks
from motor and pressure switch come in contact with flammable vapors,
combustible dust, gases or other combustible materials. When using the
air compressor for spraying paint, place the air compressor as far away from
the work area as possible, using extra lengths of air hose to extend the working reach instead of extension cords.
GROUNDING INSTRUCTIONS
This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric
current. This product is equipped with a cord having a grounding wire with an
appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.
This product is for use on a nominal 120-volt circuit and has a three-prong grounding plug that looks like the plug illustrated in Figure 1. A temporary adapter similar to the adapter illustrated in sketch B (See Page 9) may be used to connect this
plug to a 2-pole receptacle as shown in illustration B when a properly grounded
outlet is not available. The temporary adapter shall be used only until a properly
grounded outlet (Illustration A) is installed by a qualified electrician. Tab for
grounding screw, lug, or similar part extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover.
Whenever the adapter is used, it must be held in place by a metal screw.
The use of a GFCI outlet is strongly recommended. The third prong is to be
used to ground the tool and provide protection against electrical shock.
Never remove the third prong.
Check with a qualified electrician or serviceman if the grounding instructions
are not completely understood, or if in doubt as to whether the product is
properly grounded. Do not modify the plug provided. if it will not fit the outlet, have the proper outlet installed by a qualified electrician.
EXTENSION CORDS
A
B
GROUNDED RECEPTACLE
UNGROUNDED AC RECEPTACLE
COVERPLATE
MOUNTING SCREW
TOOL POWER CORD
TOOL POWER CORD
GROUNDING PIN
TAB FOR
GROUNDING SCREW
THE USE OF AN EXTENSION CORD WITH THIS PRODUCT IS NOT RECOMMENDED as this can result in the loss of power to your air compressor which
can prevent the motor from starting or running properly. This can also cause
your fuse to blow or circuit breaker to trip. Running your air compressor on an
undersized extension cord will cause permanent damage to internal switches
and overheating of the electric motor. Use an additional length of air hose rather
than an extension cord.
FIGURE 1. CONNECTING THE AIR COMPRESSOR TO THE AC POWER RECEPTACLE
If you must use an extension cord, it should be plugged into a GFCI found in circuit
boxes or protected receptacles. Use only UL listed 3-wire extension cords that have
a 3-blade grounding plug and a 3-slot receptacle that will accept the plug on the
product. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will
draw. Refer to the guide on the next page for minimum gauge required for extension cords.
9
10
GROUNDING ADAPTER
EXTENSION CORD LENGTH
WIRE SIZE (AWG)
Up to 25 Feet
14
26 to 50 Feet
12
51 to 100 Feet
Do Not Use
COMPRESSOR FEATURES
13
6
8
7
5
9
3
4
Use only extension cords that are intended for outdoor use. These cords are identified by a marking “ACCEPTABLE FOR USE WITH OUTDOOR APPLIANCES, STORE
INDOORS WHEN NOT IN USE.” Examine extension cord before use. DO NOT USE
DAMAGED EXTENSION CORDS. Do not pull on cord to disconnect from receptacle;
always disconnect by pulling on plug. Keep cord away from heat and sharp edges.
Always shut OFF the air compressor AUTO/ON pressure switch before unplugging
the compressor. Always disconnect the extension cord from the receptacle before
disconnecting the product from the extension cord.
11
12
12
1
Avoid electrical shock hazard. Never use this compressor with a damaged or frayed electrical cord or extension cord. Inspect all
electrical cords regularly. Never use in or near water or in any environment
where electric shock is possible. To reduce the risk of electrocution, keep all
connections dry and off the ground. Do not touch the plug with wet hands.
Guard against electrical shock. Avoid body contact with grounded services such as
pipes, ovens, stoves, and refrigerator enclosures. If not properly grounded, this air
compressor can incur the potential hazard of light trickle shock, particularly when
used in damp locations. If electrical shock occurs, there is the potential of secondary hazard such as your hands contacting an operating air tool.
11
2
10
12
COMPRESSOR FEATURES:
1. OIL LUBRICATION: Oil lubricated direct drive pump with cast-iron cylinder for
durability.
2. OIL FILL SIGHT GLASS: Located on the face of the crankcase, the oil fill sight
glass provides a convenient way to check the oil fill level within the pump. The
oil level must be checked prior to each use to ensure proper fill level.
Do not operate the compressor without lubricant, or with
low lubrication level. The manufacturer is not responsible for damage caused
to the compressor due to operation without proper lubrication.
3. AUTOMATIC ON/OFF PRESSURE SWITCH: This compressor is equipped with
an automatic on/off pressure switch. The compressor will only run when the
switch is in the ON/AUTO position. Once the tank has reached the desired preset pressure (“cut-out” pressure), the pump motor will automatically shut off.
While the switch is in the ON/AUTO position, the pump motor will automatically
turn back on once the pressure in the tank drops below the minimum preset
pressure (“cut-in” pressure).
Do not leave the compressor unattended while the power
switch is in the on/auto position.
4. INSTRUMENT PANEL: Top mounted instrument panel provides easy access.
5. AIR TANK PRESSURE GAUGE: The tank pressure gauge provides a reading of
the air pressure inside of the compressor tank.
6. PRESSURE REGULATOR: The regulator allows you to select the amount of air
pressure that is output through the air hose into tools and accessories. Turn the
pressure regulator knob clockwise to increase discharge pressure, and counter
clockwise to decrease discharge pressure. Please refer to the air delivery
requirements of your tools for the proper pressure settings.
CAUTION: Be careful not to overtighten pressure regulator knob when it “bottoms out” as this may damage pressure regulator.
9. SAFETY RELIEF VALVE: This compressor is equipped with a safety relief valve
that is designed to prevent system failures by relieving pressure from the system when the air pressure reaches a predetermined level. The safety relief valve
is preset by the manufacturer. DO NOT attempt to modify or remove the safety
relief valve.
10.AIR TANK DRAIN VALVE: Moisture is produced whenever air is compressed. It
is critical to drain water from the air tank on this compressor frequently. If unit
is used only occasionally, tank should be drained after each use and prior to
the next use. To drain the tank, slowly open the tank drain fitting by turning
clockwise. Once all moisture has drained out, close the fitting securely. NOTE:
Air tank will not pressurize while drain valve is open.
11.AIR INTAKE FILTER: This compressor is equipped with an externally accessible
air intake filter that is designed to clean air coming into the pump. The filter
element is easily removed for periodic cleaning. Use compressed air to blow
loose dirt and debris from the paper filter element and reinstall. Replace paper
filter element when necessary.installation instructions.
A dirty air filter will reduce air compressor performance
and can lead to product failure.
12.MANUAL THERMAL OVERLOAD SWITCH: The electric motor has a manual
thermal overload protector. If the motor overheats for any reason, the thermal
overload protector will shut off the motor. Turn pressure switch to the “off”
position and wait for unit to cool before pushing the reset button and restarting
the compressor. NOTICE: This air compressor is designed for household use
only and is not intended to operate heavy-duty air tools. If your application’s
demands exceed the capacity of this air compressor, a larger air compressor
that is matched to your application is recommended. If the unit shuts down
again, please call the consumer helpline at 1-800-590-3723 for assistance.
13.CARRY HANDLE: Convenient handle for easy transport.
7. OUTLET PRESSURE GAUGE: The outlet pressure gauge provides a reading of
the air pressure at the outlet side of the regulator. This pressure is controlled by
the pressure regulator and is always less than or equal to the air tank pressure.
8. DUAL AIR OUTLET PORTS: The air outlet ports are located on the pressure
manifold behind the instrument panel. These ports feature quick connect couplers that are preinstalled into standard 1/4" NPT (F) threads in the pressure
manifold. Use PTFE thread-sealing tape on the threads to make sure you have
an airtight connection when replacing quick connect couplers.
13
14
ASSEMBLY INSTRUCTIONS
The compressor is shipped without oil in the crankcase.
Add oil as indicated below.
STEP 1 – PUMP LUBRICATION
This air compressor features an oil lubricated pump that requires the use of SAE 30
weight non-detergent air compressor oil.
ADDING COMPRESSOR OIL:
1. Place air compressor on a flat, level
surface.
STEP 2 – INSPECTION CHECK
ASSEMBLY CHECK:
In order to complete the assembly of your new air compressor, a careful inspection
should be made to ensure that all of the parts are properly aligned and securely fastened.
1. Inspect air filter to ensure that it is installed and secure.
2. Check oil fill level in crankcase.
OPERATING THE AIR COMPRESSOR
INITIAL SETUP / BREAK-IN PROCEDURE:
2. Remove RED plastic oil fill
breather plug (see Figure 2).
Do not attach air hose, air tools or other air accessories
to the air outlet until break-in procedure has been successfully completed.
3. Open supplied oil bottle and pour oil
into crankcase until the oil level reaches
the center of the red circle in the oil
level sight glass (see Figure 3). Be
careful not to overfill.
1. Read and understand the entire instruction manual, including all safety warnings before setting up air compressor.
2. Place air compressor on a flat, level surface.
FIGURE 2
4. See diagram for determining proper oil
fill level using oil fill sight glass
(see Figure 4).
5. Install supplied RED plastic oil fill
breather plug securely into oil fill hole.
3. Check oil fill level in crankcase and add oil as needed.
4. Turn the pressure regulator knob fully clockwise to open airflow from air outlet
port.
Be careful not to overtighten pressure regulator knob when
it “bottoms out” as this may damage pressure regulator.
5. Turn the power switch to the OFF position.
CAUTION
CHECK OIL
LEVEL DAILY!
7. Open the tank drain valve to allow air to escape preventing air pressure buildup
in the air tank.
OIL LEVEL OK
FIGURE 3
8. Turn the compressor ON by moving the switch to the AUTO/ON position and
run the air compressor for a period of 20 minutes to break-in the air pump.
REFILL OIL
IMMEDIATELY
OIL CAPACITY: 28oz
(833ml)
FIGURE 4
Do not operate the compressor without lubricant, or with
low lubrication level. The manufacturer is not responsible for damage caused
to the compressor due to operation without proper lubrication.
15
6. Plug power cord directly into a properly grounded power source of the correct
voltage (see Grounding Instructions on page 5 of this instruction manual).
9. With the compressor still running, at the end of the 20-minute break-in period,
close the tank drain valve. The air compressor will build air pressure to the
maximum preset pressure (“cut-out” pressure) and automatically shut off.
10.Slowly turn the tank drain valve to open airflow from drain and bleed off air
from the air tank. The air compressor will automatically restart once the pressure in the air tank drops below the minimum preset pressure (“cut-in” pressure).
16
11.Turn the compressor off by moving the switch to the OFF position.
12.Release pressure from the system. Drain moisture from the air tank by slowly
opening the air tank drain valve by turning clockwise.
Tilt tank to remove all moisture. Once all the moisture has drained out, close
the fitting securely.
NOTE: Air tank will not pressurize while drain valve is open.
When operating in cold weather (under 45°F) the compressor must be allowed to warm up before use. This can be accomplished by
loosening drain valve enough to allow any air to escape the tanks. Start up compressor and allow to run with drain valve open for approximately 3-5 minutes
to warm up before closing drain valve and proceeding with use.
13.Disconnect the power cord from the power outlet.
NOTE: Make sure the power switch is in the OFF position when connecting or
disconnecting power cord from electrical outlet.
MAINTENANCE AND CLEANING
14.Your new air compressor is now ready to use.
STARTUP:
1. Before each startup, make sure the power switch is in the OFF position.
2. Place air compressor on a flat, level surface.
3. Check oil fill level in crankcase and add oil as needed.
Disconnect AIR COMPRESSOR from power source and
bleed off all air pressure before attempting any maintenance or repair.
SHUTDOWN AND STORAGE:
NOTE: NEVER stop the air compressor by unplugging it from the power outlet as
this may result in damage to the compressor.
4. Release pressure from the system. Drain moisture from the air tank by slowly
opening the air tank drain valve by turning clockwise. Once all the moisture
has drained out, close the fitting securely. NOTE: Air tank will not pressurize
while drain valve is open.
1. Turn the switch to the OFF position
5. Turn the pressure regulator knob fully counterclockwise to close airflow from
air outlet port.
3. Turn the pressure regulator knob fully counterclockwise to close airflow from
air outlet port. Check the outlet pressure gauge to ensure that it reads 0 PSI.
6. Attach air hose and accessories.
4. Remove the air hose and any air accessories.
Too much air pressure causes a hazardous risk of bursting.
Check the manufacturer’s maximum pressure rating for air tools and accessories.
The regulator outlet pressure must never exceed the maximum pressure rating.
7. Before connecting the compressor to the grounded outlet, check oil level, check for
broken components and accessories, and check for damage to the hose.
8. Plug power cord directly into a properly grounded power source of the correct
voltage (see Grounding Instructions on page 5 of this instruction manual).
2. Disconnect the power cord from the power outlet. Disconnect the power cord
from the power outlet by grabbing the plug (not the cord). Loop around electric
cord holder for storage.
5. Drain moisture from the air tank by slowly opening the air tank drain valve by
turning clockwise. Tilt tank to remove all moisture. Once all the moisture has
drained out, close the fitting securely.
6. Allow the compressor to cool down.
7. Wipe the air compressor clean and store it in a clean, dry, and non-freezing location.
WHEN PERFORMING ANY MAINTENANCE OR SERVICE:
1. The air compressor must be turned off.
2. Disconnect compressor from the power source.
9. Turn the compressor ON by moving the switch to the AUTO/ON position and
allow the tank pressure to build. Once the air pressure reaches the maximum
preset pressure (“cut-out” pressure) it will automatically shut off.
3. Open tank drain to bleed off all air pressure before attempting any maintenance
or repair.
10.Slowly turn the pressure regulator knob clockwise to open airflow from air outlet port until desired output pressure is reached. NOTE: The air compressor
will automatically restart once the pressure in the air tank drops below the
minimum preset pressure (“cut-in” pressure).
Check the air compressor frequently for any visible problems and follow maintenance procedures each time the compressor is used.
17
18
4. Allow compressor to fully cool before attempting any maintenance or repair.
5. Remove oil drain plug.
All air compressors contain maintenance parts that require
periodic replacement. These used parts, including air filters and used lubricating oil, may contain regulated substances that must be disposed of in accordance with local, state, and federal laws and regulations.
1. Turn compressor off and release pressure from the system. Drain moisture
from the air tank by slowly opening the air tank drain valve by turning clockwise. Tilt tank to remove all moisture. Once all the moisture has drained out,
close the fitting securely.
2. Wipe the compressor clean.
6. Allow oil to drain completely. Tilt air
compressor towards the oil drain to
assist draining.
7. Clean and replace oil drain plug.
8. Refill crankcase with SAE 30 weight
non-detergent air compressor oil until
the oil level reaches the center of the
red circle in the oil level sight glass. Be
careful not to overfill.
9. Reinstall the oil fill breather plug.
MAINTENANCE CHECKLIST:
Daily:
• Check oil level.
• Drain accumulated liquid from tank.
• Check for oil leaks.
• Check for unusual noise
and/or vibrations.
• Check that all fasteners are secure.
• Wipe compressor clean.
Weekly:
• Inspect and clean air filter.
• Clean breather holes on oil fill plug.
Monthly:
• Check for air leaks.+
• Check safety relief valve.
FIGURE 5
CHECKING SAFETY RELIEF VALVE:
Safety RELIEF valve must be replaced if it cannot be
actuated or it leaks air after the ring is released.
1. The air compressor must be turned OFF.
2. Disconnect compressor from the power source.
3. Open tank drain to bleed off all air pressure before attempting any maintenance
or repair.
SIX MONTHS OR 200 OPERATING HOURS:*
• Change compressor oil. Use only SAE 30 weight non-detergent air compressor oil.
• Replace oil more frequently when used in dusty operating environments.
+ Apply a solution of soapy water around joints. Look for air bubbles around joints
when compressor reaches the pressure cut-out limit and the pump turns off.
* The pump oil must be changed after the first 20 hours of operation. Thereafter,
change oil every 200 hours of operation or every six months, whichever comes
first. In harsh operating conditions, maintenance must be performed more frequently.
OIL CHANGE:
Used lubricating oil may contain regulated substances that must be disposed of in
accordance with local, state, and federal laws and regulations.
1. The air compressor must be turned OFF.
2. Allow compressor to fully cool before attempting any maintenance or repair.
3. Place a suitable oil drain pan below oil drain plug (see Figure 5).
4. Remove oil fill breather plug to allow air to enter crankcase.
19
4. Allow compressor to fully cool before attempting any maintenance or repair.
5. Grasp the wire ring on the safety relief valve.
6. Pull and release the ring a few times to ensure that the plunger moves in and
out. Replace the safety relief valve if plunger does not move or is difficult to
move.
CHECKING AIR FILTER ELEMENT:
1. The air compressor must be turned OFF.
2. Disconnect compressor from the power source.
3. Open tank drain to bleed off all air pressure before attempting any maintenance
or repair.
4. Allow compressor to fully cool before attempting any maintenance or repair.
5. Remove the face of the filter body to access the filter element by pushing and
rotating the front portion of the filter body in a counter clockwise direction to
release the locking tabs.
6. Use compressed air to blow loose dirt and debris from the paper filter element.
Replace filter element if it cannot be cleaned sufficiently.
7. Reinsert filter element into filter body and reinstall filter faceplate.
MOISTURE IN COMPRESSED AIR
Moisture is a normal by-product of compressing air. As the moisture builds during
compressor use, it can be carried though the air hose. When using paint spray gun
or sandblasting gun, the use of a special filter to remove moisture from the air line
is highly recommended. Moisture in the compressed air will cause water spots in
paint jobs and cause blasting media to clog the sandblasting gun.
TROUBLESHOOTING GUIDE
THE COMPRESSOR DOES NOT START OR RESTART:
THE COMPRESSOR MOTOR STALLS:
PROBABLE CAUSE:
Overloaded motor.
Improper lubrication.
Low oil level.
Defective check valve.
PROBABLE CAUSE:
Power cord not plugged in.
Motor/Pressure switch in
OFF position
Motor thermal overload
switch has tripped
SOLUTION:
Plug cord into grounded outlet.
Move switch to AUTO position.
Fuse blown or circuit
breaker has tripped.
Replace fuse or reset circuit breaker.
Check for proper fuse amperage.
Check for low voltage conditions.
Disconnect any other electrical appliances from
circuit or operate air compressor on its own
branch circuit.
Wrong gauge wire or length
of extension cord.
Air tank pressure exceeds
motor/pressure switch
"cut-in" pressure.
Pressure release valve on
motor/pressure switch has
not unloaded pump head
pressure.
Defective motor, motor
capacitor, motor/pressure
switch.
Check chart in instruction manual for proper gauge
wire and cord length.
Worn bearings.
Motor will start automatically when air tank
pressure drops below "cut-in" pressure of
motor/pressure switch.
Noisy check valve.
Turn air compressor off, wait until the
motor is cool, then press motor thermal
overload (red) button firmly until click is
heard.
Bleed the line by moving the switch to the OFF
position.
Contact Consumer Helpline at 1-800-590-3723
21
SOLUTION:
Have a certified electrician check the motor
and wiring. Proceed with his or her
recommendations.
See LUBRICATION section in instruction
manual.
Check oil level and fill if necessary.
Replace check valve.
EXCESSIVELY NOISY OPERATION:
PROBABLE CAUSE:
Loose motor pulley
or pump flywheel.
Lack of oil in the pump
crankcase.
Carbon deposits on pistons
or valves.
Bearing, piston or connecting
rod failure.
Worn connecting rod.
Worn piston wrist pin bushing.
SOLUTION:
Tighten pulley and/or flywheel
(where applicable).
Check oil level. If low, check for possible
bearing damage. Add correct amount of oil.
Remove cylinder head and inspect.
Clean or replace parts as needed.
STOP THE COMPRESSOR! Contact
Consumer Helpline at 1-800-590-3723.
Replace with new connecting rod.
Remove piston/connecting rod assembly from
the compressor and inspect for excess wear.
Replace worn parts as needed.
Replace worn bearings as needed.
Note: Dirty oil can cause accelerated wear.
Change oil frequently using recommended oil.
Replace check valve.
WHEN IN THE START / STOP OPTION, MOTOR RUNS CONTINUOUSLY:
PROBABLE CAUSE:
Motor/Pressure switch does
not shut off motor when air
compressor reaches "cut-out"
pressure and safety relief
valve activates
Air compressor is incorrectly
sized.
SOLUTION:
Move the motor/pressure switch to the OFF
position. If the motor does not shut off,
unplug the air compressor. If the electrical
contacts are welded together, replace the
pressure switch.
Limit the air pressure to the capacity of the air
compressor. Either use a smaller tool or a
larger air compressor.
22
OVERHEATING:
PROBABLE CAUSE:
Poor ventilation
Dirty cooling fins.
AIR LEAKS AT FITTINGS:
SOLUTION:
Relocate the air compressor to an area with an
ample supply of cool, dry, and well-circulated
air is available.
Clean the outer surfaces of the cooling fins on
the pump and motor assembly.
AIR CONTINUES TO LEAK AT MOTOR/PRESSURE SWITCH RELEASE VALVE
AFTER MOTOR STOPS:
PROBABLE CAUSE:
Defective pilot valve, the check
valve is stuck open.
SOLUTION:
Remove, clean or replace.
AIR CONTINUES TO LEAK AT MOTOR/PRESSURE SWITCH RELEASE VALVE
WHILE MOTOR IS RUNNING:
PROBABLE CAUSE:
Defective motor/pressure switch
Check valve stuck in open
position.
SOLUTION:
Replace.
Replace check valve.
DANGER– Do not disassemble the check valve
with tank pressurized. Open tank petcock
valve to allow air to escape from tank prior to
servicing.
AIR LEAKS FROM SAFETY RELIEF VALVE:
PROBABLE CAUSE:
Possible defective safety
relief valve.
Excessive tank pressure.
SOLUTION:
Operate safety relief valve manually by pulling
on ring. If it still leaks, it should be replaced.
Defective motor/pressure switch. Replace.
AIR LEAKS AT PUMP:
PROBABLE CAUSE:
Blown gaskets.
SOLUTION:
Replace blown gaskets and torque head bolts
to 20 ft./lbs. CAUTION– Replace head gasket
with a new one each time the head is removed
to ensure proper sealing.
23
PROBABLE CAUSE:
Fittings are not tight enough.
SOLUTION:
Tighten fittings where air can be heard
escaping. Check fittings with soapy water
solution. DO NOT OVERTIGHTEN.
AIR LEAKS IN AIR TANK:
PROBABLE CAUSE:
Defective or rusted air tank.
SOLUTION:
Air tank must be replaced. DO NOT ATTEMPT
TO REPAIR AIR TANK!
AIR BLOWING FROM INLET FILTER:
PROBABLE CAUSE:
Damaged inlet (reed) valve.
SOLUTION:
Contact Consumer Helpline at
1-800-590-3723.
INSUFFICIENT PRESSURE AT AIR TOOL OR AIR ACCESSORY:
PROBABLE CAUSE:
Pressure regulator knob is
not turned to high enough
pressure.
Defective motor/pressure
regulator switch.
Restricted air intake filter.
Air leaks.
Hose or hose connections
are too small or long.
Air compressor is not large
enough for air requirement.
SOLUTION:
Adjust pressure regulator knob to proper setting.
Replace.
Clean or replace the filter element.
Check for leaks by applying soap solution to
all fittings and connections. Bubbles will
appear at leakage points. Tighten or replace
leaking fittings or connections as needed.
Replace with larger hose or connectors.
Check the accessory air requirement. If it is
higher than the CFM or pressure supply of the
air compressor, you need a larger air
compressor.
24
AIR COMPRESSOR NOT MAKING ENOUGH AIR:
PROBABLE CAUSE:
Restricted air intake filter.
Leaking (reed) valve.
Restricted pilot valve.
Low compression.
SOLUTION:
Clean or replace the filter element.
Drain air tank and measure pump up time.
Compare to specifications. If lower, remove
pump head and inspect valve plate, valve
seats, and valve reeds. Clean or replace as
needed.
Clean or replace.
Low pressure may be due to worn piston
rings and cylinder walls. Inspect for excessive
wear and replace worn parts as needed.
EXCESSIVE OIL CONSUMPTION:
PROBABLE CAUSE:
Restricted air intake filter.
Air compressor on unlevel
surface.
Crankcase overfilled with oil.
Plugged oil dipstick vent.
Oil leaks.
Worn piston rings or
scored cylinder.
Improper oil viscosity.
SOLUTION:
Clean or replace air filter element.
Do not incline the air compressor more
than 10 degrees in any direction while running.
Drain oil. Refill to proper level with 30 weight
non-detergent air compressor oil.
Clean and check breather for proper
ventilation.
Repair.
Replace worn or damaged parts as needed.
Drain oil. Refill to proper level with 30 weight
non-detergent air compressor oil.
OIL HAS MILKY APPEARANCE:
PROBABLE CAUSE:
Water in oil due to
condensation.
SOLUTION:
Change oil and move air compressor to a less
humid environment.
MOISTURE IN DISCHARGE AIR:
PROBABLE CAUSE:
Condensation in air tank
caused by high level of
atmospheric humidity or air
compressor is not running
long enough.
SOLUTION:
Drain tank after every use. Drain air tank
more often in humid weather and use
an air line filter.
PARTS LIST
NO.
PART NO.
DESCRIPTION
1
691298-1
Bolt
4
2
691298-2
Spring Washer
4
3
691298-3
Cylinder Head
1
4
691298-4
Exhaust Elbow
1
5
691298-5
Gasket, Cylinder Head
1
6
691298-6
Valve Plate
1
7
691298-7
Bolt
2
8
691298-8
Spring Washer
2
9
691298-9
Plate Washer
2
10
691298-10
Valve Plate
1
11
691298-11
Reed Valve, Intake
1
12
691298-12
Pin
2
13
691298-13
Reed Valve, Exhaust
1
14
691298-14
Piston
1
15
691298-15
Valve Plate Gasket
1
16
691298-16
Cylinder
1
17
691298-17
Cylinder Base Gasket
1
18
691298-18
Compression Ring
2
19
691298-19
Oil Ring
1
20
691298-20
Piston Pin
1
21
691298-21
Circlip
2
22
691298-22
Connecting Rod
1
23
691298-23
Crank Shaft
1
24
691298-24
Bolt LH
1
26
QTY
PARTS LIST
NO.
PART NO.
DESCRIPTION
25
691298-25
26
PARTS LIST
QTY
NO.
PART NO.
DESCRIPTION
QTY
Oil Fill Plug
1
50
691298-50
Spring Washer
4
691298-26
Screw
6
51
691298-51
Wave Washer
1
27
691298-27
Oil Sight
1
52
691298-52
Circlip for Motor Shaft
1
28
691298-28
Oil Sight Seal Ring
1
53
691298-53
Motor Shroud
1
29
691298-29
Crankcase Cover
1
54
691298-54
Bolt
2
30
691298-30
Rubber Gasket
1
55
691298-55
Screw
2
31
691298-31
O-Ring
1
56
691298-56
Nut
1
32
691298-32
Crankcase
1
57
691298-57
Bolt
1
33
691298-33
Nut
4
58
691298-58
Pressure Guage (0-200psi)
2
34
691298-34
Plate Washer
8
59
691298-59
Quick Coupler
2
35
691298-35
Bolt
4
60
691298-60
Safety Valve (140psi)
1
36
691298-36
Oil Drain Plug
1
61
691298-61
Nut
1
37
691298-37
Nut
1
62
691298-62
Plug 1/8 NPT
2
38
691298-38
Washer
1
63
691298-63
Manifold
1
39
691298-39
Capacitor
1
64
691298-64
Elbow
1
40
691298-40
Spring Washer
2
65
691298-65
Bracket
1
41
691298-41
Plate Washer
2
66
691298-66
Plate Washer
2
42
691298-42
Bolt
2
67
691298-67
Bolt
2
43
691298-43
Bearing
1
68
691298-68
Front Plate
1
44
691298-44
Rotor
1
69
691298-69
Bolt
6
45
691298-45
Bearing
1
70
691298-70
Plate Washer
6
46
691298-46
Stator
1
71
691298-71
Nut
6
47
691298-47
Motor Back Cover
1
72
691298-72
Sleeve
1
48
691298-48
Motor Fan
1
73
691298-73
Pressure Switch
1
49
691298-49
Bolt
4
28
PARTS LIST
PARTS LIST
NO.
PART NO.
DESCRIPTION
QTY
NO.
PART NO.
DESCRIPTION
74
691298-74
Plug 1/4 NPT
3
98
691298-98
Power Cord
1
75
691298-75
Connector
1
99
691298-99
Air Filter Kit
1
76
691298-76
Nut G3/8
1
100
691298-100
Thermal Overload Switch
1
77
691298-77
Gasket
1
78
691298-78
Connecting
1
79
691298-79
Check Valve
1
80
691298-80
Grip Handle
1
81
691298-81
Tank 2 x 2.5 Gallon
1
82
691298-82
Rubber Plug
2
83
691298-83
Drain Valve
1
84
691298-84
Padding
4
85
691298-85
Bolt
4
86
691298-86
Plate Washer
4
87
691298-87
Rubber Footpad
4
88
691298-88
Exhaust Tube
1
89
691298-89
Fin Tubing
1
90
691298-90
Nut
4
91
691298-91
Copper Washer
4
92
691298-92
Strain Relief
2
93
691298-93
Inlet Tube
1
94
691298-94
Unloader Tube
1
95
691298-95
Nut
1
96
691298-96
Cable Connector (O)
2
97
691298-97
Cable Connector (U)
1
29
PARTS DIAGRAM
30
QTY
PARTS DIAGRAM
1 YEAR LIMITED WARRANTY
ALLTRADE TOOLS LLC AIR COMPRESSORS
Express and Exclusive Limited Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter “Alltrade”) expressly warrants to the original retail
purchaser of the accompanying air compressor and no one else all parts of the
product (except those parts referred to below which are specifically excluded from
such warranty (see Exclusions)) to be free from defects in materials and workmanship during the following periods from the original date of purchase:
For one (1) year from the date of purchase:
• Compressor Pump
• Tank assembly
• Plumbing
31
For six (6) months from date of original purchase:
• Pressure Switch
• Regulator
• Pilot Valve
• Check Valve
• Copper/Stainless Steel Line
For ninety (90) days from the original date of purchase:
• Pressure Gauge
• Safety Release Valves
• Drain Valve
• Quick Couplers
For thirty (30) days from the original date of purchase:
• Air Accessories
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified or altered. This warranty does not apply to any other
product and/or component thereof manufactured or distributed by Alltrade, and
does not apply to products and/or components thereof designed, manufactured
and/or assembled by others, for which Alltrade makes no warranties whatsoever.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF.
Warranty Performance
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (ADDRESS: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service (TELEPHONE: 1800-590-3723.) within the applicable warranty period, with a written request by purchaser that Alltrade repair and/or replace the nonconforming item and/or part. We
recommend that you keep the original product packaging in the event you need to
ship the unit. We suggest the package be insured against loss or in transit damage.
When sending your product include your name, address, phone number, dated
proof of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion to
determine whether any item or part is nonconforming and, if so, whether the item
and/or part will be repaired and/or replaced. If Alltrade chooses to replace the product, it may replace it with a new or reconditioned one of the same or comparable
design. The repaired or replaced unit will be warranted under the terms of the
remainder of applicable warranty period(s). Typically, covered defective parts not
subject to normal wear and tear or other exclusions will be repaired or replaced, at
Alltrade’s option, during the above stated warranty periods. Alltrade’s repair and/or
replacement of any nonconforming item and/or part thereof shall constitute fulfillment of all obligations to the purchaser. Alltrade shall not be responsible or liable
for any expense, including freight charges, or repairs made outside Alltrade’s facility, unless expressly agreed to by Alltrade in writing. Under no circumstances shall
Alltrade bear any responsibility for loss of the unit, loss of time or rental, inconvenience, commercial loss or consequential damages.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal conditions, misapplication, misuse, abuse, accidents, operation at other than recommended pressures or temperatures, improper storage or freight damage. Parts
damaged or worn by operation in dusty environments are not warranted. Failure to
follow recommended operating and maintenance procedures also voids warranty.
The following additional items are not covered under this warranty: pump or valve
failure caused by rain, excessive humidity, corrosive environments or other contaminants; cosmetic defects that do not interfere with compressor functionality; and
rusted tanks, including but not limited to rust due to improper drainage or corrosive
environments.
This warranty shall not apply when: the air compressor has been used for commercial or rental purposes; defects in materials or workmanship or damages result from
repairs or alterations which have been made or attempted by others or the unauthorized use of nonconforming parts; damage is due to abuse (including overloading
of the air compressor beyond capacity), improper maintenance, neglect or accident,
or the damage is due to use of the air compressor after partial failure or use with
improper accessories.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons; pre-delivery services such as assembly, oil or lubricants, and adjustment; maintenance services that are normally required to maintain the air compressor.
The use of other than genuine Alltrade Repair Parts will void warranty.
Warranty Disclaimers
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE AIR
COMPRESSOR OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY
AND/OR BY ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED
BY ALLTRADE AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND
WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS
AND/OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PUR-
CHASER’S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE WARRANTY IS MADE WITH REGARD TO THIS AIR COMPRESSOR. ALL EXPRESS
AND/OR IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY
ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE AIR COMPRESSOR OR
ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER
ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION, WRITTEN OR
ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR
OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE,
ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR
ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY
AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION
ARISING THEREFROM OR BASED THEREON.
PURCHASER’S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER, AND/OR THE
EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF
ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES. IN NO
EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT, WARRANTY, TORT
(INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL ALLTRADE’S AND/OR ITS
REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF THE AIR COMPRESSOR.
ANY AND ALL LIABILITY CONNECTED WITH THE USE OF THIS AIR COMPRESSOR
SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE.
Limitations on Warranty Disclaimers
Some states do not allow limitations on how long an implied warranty lasts and
some states do not allow the exclusion or limitation of the incidental or consequential damages, so part or all of the above limitations or exclusions may not apply to
you. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department at 1-800-590-3727 for general repair information and charges.
34
Download PDF

advertising