Owner’s Manual
For professional use only
Do not use this equipment
before reading this manual!
PowrTex 1200 SF
Airless Texture and Paint Sprayer
Model Numbers:
Complete
Bare
Printed in USA
600-150
600-151
NOTE: This manual contains important warnings
and instructions. Please read and retain
for reference.
0110 •
© Titan Tool Inc. All Rights Reserved. Form No. 0528920A
Important Safety Information ·
Read all safety information before
operating the equipment. Save these instructions.
This symbol indicates a hazardous situation,
which, if not not avoided could result in death or
serious injury.
HAZARD:HAZARDOUS VAPORS
Paints, solvents, insecticides, and other materials
can be harmful if inhaled or come in contact with the
body. Vapors can cause severe nausea, fainting, or
poisoning.
To reduce the risks of fire or explosion, electrical
shock and the injury to persons, read and
understand all instructions included in this manual.
Be familiar with the controls and proper usage of
the equipment.
PREVENTION:
• Use a respirator or mask if vapors can be
inhaled. Read all instructions supplied
with the mask to be sure it will provide the
necessary protection.
• Wear protective eyewear.
• Wear protective clothing as required by coating manufacturer.
HAZARD: Injection injury
A high pressure paint stream produced by this
equipment can pierce the skin and underlying
tissues, leading to serious injury and possible
amputation. See a physician immediately.
DO NOT TREAT AN INJECTION INJURY AS A SIMPLE
CUT! Injection can lead to amputation. See a physician
immediately.
The maximum operating range of the sprayer is 3300 PSI / 22.8
MPa fluid pressure.
PREVENTION:
• NEVER aim the gun at any part of the body.
• Do not aim the gun at, or spray any person or animal.
• NEVER allow any part of the body to touch the fluid stream.
DO NOT allow body to touch a leak in the fluid hose.
• NEVER put your hand in front of the gun. Gloves will not
provide protection against an injection injury.
• ALWAYS lock the gun trigger, shut the pump off, and
release all pressure before servicing, cleaning the tip or
guard, changing tip, or leaving unattended. Pressure will
not be released by turning off the motor. The PRIME/
SPRAY valve or pressure bleed valve must be turned to
their appropriate positions to relieve system pressure.
Refer to the PRESSURE RELIEF PROCEDURE
described in this manual.
• ALWAYS keep the tip guard in place while spraying. The
tip guard provides some protection but is mainly a warning
device.
• ALWAYS remove the spray tip before flushing or cleaning
the system.
• Paint hose can develop leaks from wear, kinking and
abuse. A leak can inject material into the skin. Inspect
the hose before each use. Do not use hose to lift or pull
equipment.
• NEVER use a spray gun without a working trigger lock and
trigger guard in place.
• All accessories must be rated at or above 3300 PSI / 22.8
MPa. This includes spray tips, guns, extensions, and hose.
• Do not leave the unit energized or under pressure while
unattended. When the unit is not in use, turn off the unit and
relieve the pressure in accordance with the PRESSURE
RELIEF PROCEDURE described in this manual.
• Verify that all connections are secure before operating the
unit. Unsecured parts may eject at great force or leak a
high pressure fluid stream causing severe injury.
• Always engage the trigger lock when not spraying. Verify
the trigger lock is functioning properly.
HAZARD: EXPLOSION OR FIRE
Solvent and paint fumes can explode or ignite.
Property damage and/or severe injury can occur.
PREVENTION:
• Provide extensive exhaust and fresh air introduction to
keep the air within the spray area free from accumulation
of flammable vapors. Solvent and paint fumes can
explode or ignite.
• Do not spray in a confined area.
• Avoid all ignition sources such as static
electric sparks, open flames, pilot lights,
electrical appliances, and hot objects.
Connecting or disconnecting power cords or
working light switches can make sparks. Paint
or solvent flowing through the equipment is
able to result in static electricity.
• Do not smoke in spray area.
• Fire extinguisher must be present and in good working
order.
• Place pump at least 25 feet (7.62 meters) from the
spray object in a well ventilated area (add more hose if
necessary). Flammable vapors are often heavier than air.
Floor area must be extremely well ventilated. The pump
contains arcing parts that emit sparks and can ignite vapors.
• The equipment and objects in and around the spray area
must be properly grounded to prevent static sparks.
• Keep area clean and free of paint or solvent containers,
rags and other flammable materials.
• Use only conductive or grounded high pressure fluid hose.
Gun must be grounded through hose connections.
• For electric units — power cord must be connected to a
grounded circuit.
• Always flush unit into a separate metal container, at low
pump pressure, with spray tip removed. Hold gun firmly
against side of container to ground container and prevent
static sparks.
• Follow the material and solvent manufacturer’s warnings
and instructions. Know the contents of the paints and
solvents being sprayed. Read all Material Safety Data
Sheets (MSDS) and container labels provided with
the paints and solvents. Follow the paint and solvent
manufacturer’s safety instructions.
• Use extreme caution when using materials with
a flashpoint below 70ºF (21ºC). Flashpoint is the
temperature that a fluid can produce enough vapors to
ignite.
• Plastic can cause static sparks. Never hang plastic to
enclose a spray area. Do not use plastic drop cloths when
spraying flammable materials.
• Use lowest possible pressure to flush equipment.
• Do not spray onto pump assembly.
note to physician:
Injection into the skin is a traumatic injury. It is
important to treat the injury as soon as possible. DO
NOT delay treatment to research toxicity. Toxicity is a
concern with some coatings injected directly into the
blood stream. Consultation with a plastic surgeon or
reconstructive hand surgeon may be advisable.
2
© Titan Tool Inc. All rights reserved.
Important Safety Information ·
Read all safety information before
operating the equipment. Save these instructions.
Grounding Instructions
HAZARD: EXPLOSION HAZARD DUE TO
INCOMPATIBLE MATERIALS
Will cause property damage or severe injury.
PREVENTION:
• Do not use materials containing bleach or
chlorine.
• Do not use halogenated hydrocarbon solvents such as
bleach, mildewcide, methylene chloride and 1,1,1 trichloroethane. They are not compatible with aluminum.
• Contact your coating supplier about the compatibility of
material with aluminum.
This product must be grounded. In the event of an electrical
short circuit, grounding reduces the risk of electric shock by
providing an escape wire for the electric current. This product is
equipped with a cord having a grounding wire with an appropriate
grounding plug. The plug must be plugged into an outlet that
is properly installed and grounded in accordance with all local
codes and ordinances.
WARNING - Improper installation of the grounding plug can
result in a risk of electric shock.
If repair or replacement of the cord or plug is
necessary, do not connect the green grounding wire
to either flat blade terminal. The wire with insulation
having a green outer surface with or without yellow
stripes is the grounding wire and must be connected
to the grounding pin.
Check with a qualified electrician or serviceman if the grounding
instructions are not completely understood, or if you are in doubt
as to whether the product is properly grounded. Do not modify
the plug provided. If the plug will not fit the outlet, have the
proper outlet installed by a qualified electrician.
HAZARD: GENERAL
Can cause severe injury or property damage.
PREVENTION:
• Read all instructions and safety precautions before
operating equipment.
• Follow all appropriate local, state, and national codes
governing ventilation, fire prevention, and operation.
• The United States Government Safety Standards have
been adopted under the Occupational Safety and Health
Act (OSHA). These standards, particularly part 1910 of
the General Standards and part 1926 of the Construction
Standards should be consulted.
• Use only manufacturer authorized parts. User assumes
all risks and liabilities when using parts that do not meet
the minimum specifications and safety requirements of the
pump manufacturer.
• All hoses, fittings, and filter parts must be secured before
operating spray pump. Unsecured parts can eject at great
force or leak a high pressure fluid stream causing severe
injury.
• Before each use, check all hoses for cuts, leaks, abrasion
or bulging of cover. Check for damage or movement of
couplings. Immediately replace the hose if any of these
conditions exist. Never repair a paint hose. Replace it with
another grounded high-pressure hose.
• Do not kink or over-bend the hose. Airless hose can
develop leaks from wear, kinking and abuse. A leak can
inject material into the skin.
• Do not expose the hose to temperatures or pressures in
excess of those specified by manufacturer.
• Do not spray outdoors on windy days.
• Wear clothing to keep paint off skin and hair.
• Do not operate or spray near children. Keep children
away from the equipment at all times.
• Do not overreach or stand on an unstable support. Keep
effective footing and balance at all times.
• Use lowest possible pressure to flush equipment.
• Stay alert and watch what you are doing.
• Do not operate the unit when fatigued or under the
influence of drugs or alcohol.
• For electric units — Always unplug cord from outlet before
working on equipment.
• Do not use the hose as a strength member to pull or lift the
equipment.
• Do not lift by cart handle when loading or unloading.
© Titan Tool Inc. All rights reserved.
Grounded Outlet
Grounding Pin
Cover for grounded outlet box
Important: Use only a 3-wire extension cord that has
a 3-blade grounding plug and a 3-slot receptacle that will
accept the plug on the product. Make sure your extension
cord is in good condition. When using an extension cord,
be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. A 12
gauge cord is recommended. If an extension cord is to be
used outdoors, it must be marked with the suffix W-A after
the cord type designation. For example, a designation of
SJTW-A would indicate that the cord would be appropriate
for outdoor use.
important: When the sprayer is used with a generator
or uncontrolled line voltage, the use of Titan’s “Line Surge
Protector” (P/N 800-935) is recommended.
Specifications
Gallons per minute (GPM)���������������1.2 (4.5 LPM)
Maximum tip sizes���������������������������0.034
Maximum pressure��������������������������3300 PSI (22.8 MPa)
Voltage��������������������������������������������100~120V AC, 50/60 Hz
Power����������������������������������������������.2.4 HP Infinity Plus
Brushless® DC Motor
Maximum current consumption�������15 A
Weight���������������������������������������������95 lbs. (43.1 kg)
Maximum hose length���������������������300’ (91.4 m)
NOTE: Maximum hose length may vary depending
on the hose diameter and the viscosity of the
material being sprayed.
3
Setup
Table of Contents
Safety Precautions.................................................................... 2
Français............................................................................. 16
Español.............................................................................. 18
General Description.................................................................. 4
Operation.................................................................................... 4
Setup........................................................................................... 4
Preparing to Spray............................................................... 5
Spraying............................................................................... 5
Control Panel Indicators....................................................... 6
Pressure Relief Procedure................................................... 6
Xact Digital Control System Operation (if equipped)............ 6
Spraying Technique.................................................................. 8
Practice................................................................................ 8
Cleanup...................................................................................... 9
Cleaning the Inlet Screen..................................................... 9
Maintenance............................................................................... 9
General Repair and Service Notes...................................... 9
Replacing the Motor Assembly.......................................... 10
Replacing the Gears.......................................................... 10
Replacing the Transducer.................................................. 11
Replacing the PRIME/SPRAY Valve.................................. 11
Servicing the Fluid Section................................................. 12
Replacing the Filters.......................................................... 13
Troubleshooting...................................................................... 14
Xact Digital Control System Error Messages..................... 15
Parts Listings........................................................................... 20
Main Assembly................................................................... 20
Drive Assembly.................................................................. 21
Fluid Section Assembly...................................................... 22
High Rider Cart.................................................................. 23
Filter Plug Assembly.......................................................... 23
PRIME/SPRAY Valve Assembly........................................ 23
Filter Parts.......................................................................... 24
Labels................................................................................. 24
Accessories........................................................................ 26
Warranty................................................................................... 28
Perform the following procedure before plugging in the power
cord of an electric sprayer.
NOTE: If the sprayer will be used for spraying textured
products, removal of the inlet screen in the foot
valve may be necessary. This will allow proper
priming and flow of the textured product. Refer
to “Cleaning the Inlet Screen” in the Cleanup
section of this manual for removal instructions.
1. Ensure that the return hose is attached and secure.
2. Using a wrench, attach a minimum of 50’ of 1/4” nylon
airless spray hose to the outlet fitting on the sprayer.
Tighten securely.
3. Attach an airless spray gun to the spray hose. Using two
wrenches (one on the gun and one on the hose), tighten
securely.
NOTE: Do not attach the tip to the spray gun yet.
Remove the tip if it is already attached.
Make sure all airless hoses and spray guns are
electrically grounded and rated at or above the
maximum operating pressure range of the airless
sprayer.
4. Make sure the pressure control knob is in its OFF position
in the black zone.
5. Fill the oil cup with one tablespoon of piston seal lubricant
(Piston Lube).
Important: Never operate unit for more than ten seconds
without fluid. Operating this unit without fluid will cause
unnecessary wear to the packings.
6. Make sure the electrical service is 120V, 15 amp minimum.
7. Plug the power cord into a properly grounded outlet at
least 25’ from the spray area.
General Description
Important: Always use a minimum 12 gauge, three-wire
extension cord with a grounded plug. Never remove the
third prong or use an adapter.
This airless sprayer is a precision power tool used for spraying
many types of materials including textured products from a
ready-mixed or powdered formulation. Read and follow this
instruction manual carefully for proper operating instructions,
maintenance, and safety information.
Preparing a New Sprayer
If this sprayer is new, it is shipped with test fluid in the fluid
section to prevent corrosion during shipment and storage. This
fluid must be thoroughly cleaned out of the system with mineral
spirits before you begin spraying.
Important: Always keep the trigger lock on the spray gun
in the locked position while preparing the system.
1. Place the foot valve into a container of mineral spirits that
has a flash point of 140ºF (60ºC) or above.
2. Place the return hose into a metal waste container.
3. Set the pressure to minimum by turning the pressure
control knob to the “Min” setting in the yellow zone.
Motor
Pressure
Control
Knob
Spray Gun
w/ Splatter
Nozzle
Control
Panel
Indicators
Filter
Plug
Oil Cup
Min. – 1900 PSI (yellow zone)
PRIME/
SPRAY
Valve
Fluid
Section
Solid Green
1901-3300 PSI
OFF (black zone)
Return
Hose
Turbo PulseClean (red zone)
Outlet
Fitting
Max PSI
(Bar)
Pressure Control Knob
4. Move the PRIME/SPRAY valve down to the
PRIME position.
5. Turn on the sprayer by moving the ON/OFF
switch to the ON position.
6. Allow the sprayer to run for 15–30 seconds to
flush the test fluid out through the return hose
and into the waste container.
7. Turn off the sprayer by moving the ON/OFF switch to the
OFF position.
Operation
This equipment produces a fluid stream at extremely
high pressure. Read and understand the warnings
in the Safety Precautions section at the front of this
manual before operating this equipment.
Min PSI
(Bar)
lse
Pu ean
Cl
Motor Running
Foot
Valve
1901 – 3300 PSI
(green zone)
Blinking Yellow
0-200 PSI
Solid Yellow
201-1900 PSI
4
© Titan Tool Inc. All rights reserved.
Preparing to Spray
Spraying
1. Prepare the material to be sprayed according to the
guidelines given by the material manufacturer.
2. Place the foot valve into a container of material.
3. Place the return hose into a metal waste
container.
4. Set the pressure to minimum by turning the
pressure control knob to the “Min” setting in
the yellow zone.
5. Move the PRIME/SPRAY valve down to the
PRIME position.
Before spraying, it is important to make sure that the fluid in the
system is compatible with the material that is going to be used.
NOTE: Incompatible fluids and material may cause
the valves to become stuck closed, which
would require disassembly and cleaning of the
sprayer’s fluid section.
Min PSI
(Bar)
lse
Pu an
Cle
Important: Always keep the trigger lock on the spray gun
in the locked position while preparing the system.
1. Place the foot valve into a container of the appropriate
solvent for the material being sprayed (refer to
recommendations of the material manufacturer). An
example of an appropriate solvent is water for latex paint.
2. Place the return hose into a metal waste
container.
3. Set the pressure to minimum by turning the
pressure control knob to the “Min” setting in
the yellow zone.
4. Move the PRIME/SPRAY valve down to
the PRIME position.
NOTE:Hold the return hose in the waste
container when moving the PRIME/
SPRAY valve to PRIME in case the
sprayer is pressurized.
6. Turn on the sprayer by moving the ON/OFF switch to the
ON position.
7. Allow the sprayer to run until material is coming through
the return hose into the metal waste container.
8. Turn off the sprayer by moving the ON/OFF switch to the
OFF position.
9. Remove the return hose from the waste container and place
it in its operating position above the container of material.
10. Move the PRIME/SPRAY valve up to the
SPRAY position.
11. Turn on the sprayer.
12. Unlock the gun by turning the gun trigger
lock to the unlocked position.
Min PSI
(Bar)
lse
Pu an
Cle
Max PSI
(Bar)
NOTE:Hold the return hose in the waste
container when moving the PRIME/
SPRAY valve to PRIME in case the
sprayer is pressurized.
5. Turn on the sprayer by moving the ON/OFF switch to the
ON position.
6. Allow the sprayer to run for 15–30 seconds to flush the
old solvent out through the return hose and into the metal
waste container.
7. Turn off the sprayer by moving the ON/OFF switch to the
OFF position.
NOTE: Make sure that the spray gun does not have a tip
or tip guard installed.
13.
8. Move the PRIME/SPRAY valve up to the
SPRAY position.
9. Turn on the sprayer.
10. Unlock the gun by turning the gun trigger
lock to the unlocked position.
11.
12.
13.
14.
15.
14.
15.
16.
Ground the gun by holding it
against the edge of the metal
container while flushing. Failure to
do so may lead to a static electric
discharge, which may cause a fire.
Trigger the gun into the metal waste container until the old
solvent is gone and fresh solvent is coming out of the gun.
Lock the gun by turning the gun trigger
lock to the locked position.
Set down the gun and increase the
pressure by turning the pressure
control knob slowly clockwise into the
green zone.
Trigger lock in
Check the entire system for leaks. If
locked position.
leaks occur, follow the “Pressure Relief
Procedure” in this manual before tightening any fittings or
hoses.
Follow the “Pressure Relief Procedure” in this manual
before changing from solvent to material.
Ground the gun by holding it
against the edge of the metal
container while flushing. Failure to
do so may lead to a static electric
discharge, which may cause a fire.
Trigger the gun into the metal waste container until all air
and solvent is flushed from the spray hose and material is
flowing freely from the gun.
Lock the gun by turning the gun trigger
lock to the locked position.
Turn off the sprayer.
Attach tip guard and tip to the gun
as instructed by the tip guard or tip
Trigger lock in
manuals.
locked position.
POSSIBLE INJECTION HAZARD.
Do not spray without the tip guard in place. Never
trigger the gun unless the tip is in either the spray or
the unclog position. Always engage the gun trigger
lock before removing, replacing or cleaning tip.
NOTE: When spraying textured products, the use
of a splatter nozzle on the spray gun may be
necessary. The splatter nozzle adds atomizing
air to the fluid stream to create the desired
material consistency. Refer to the Splatter
Nozzle Instruction Sheet (P/N 313-2468) for
detailed instructions.
17. Turn on the sprayer.
18. Increase the pressure by turning the pressure control knob
slowly clockwise toward the green zone and test the spray
pattern on a piece of cardboard. Adjust the pressure
control knob until the spray from the gun is completely
atomized. Try to keep the pressure control knob at the
lowest setting that maintains good atomization.
Be sure to follow the pressure relief procedure
when shutting down the sprayer for any purpose,
including servicing or adjusting any part of the
spray system, changing or cleaning spray tips, or
preparing for cleanup.
© Titan Tool Inc. All rights reserved.
Max PSI
(Bar)
NOTE: Turning the pressure up higher than needed to
atomize the paint will cause premature tip wear
and additional overspray.
NOTE: If the sprayer is equipped with an Xact Digital
Control System, go to “Xact Digital Control
System Operation” at the end of the Operation
section of this Manual.
5
Control Panel Indicators
Pressure Relief Procedure
The following is a description of the control panel indicators.
Blinking Yellow
0-200 PSI
Solid Yellow
201-1900 PSI
Pressure
Indicator
Motor Running
Indicator
Be sure to follow the pressure relief procedure
when shutting the unit down for any purpose,
including servicing or adjusting any part of the
spray system, changing or cleaning spray tips, or
preparing for cleanup.
Solid Green
1901-3300 PSI
Min PSI
(Bar)
1. Lock the gun by turning the gun trigger
lock to the locked position.
2. Turn off the sprayer by moving the ON/
OFF switch to the OFF position.
3. Turn the pressure control knob
counterclockwise to its OFF position in Trigger lock in
the black zone.
locked position.
4. Unlock the gun by turning the gun
trigger lock to the unlocked position.
5. Hold the metal part of the gun firmly to
the side of a metal container to ground
the gun and avoid a build up of static
electricity.
6. Trigger the gun to remove any
pressure that may still be in the hose.
7. Lock the gun by turning the gun trigger lock
to the locked position.
8. Move the PRIME/SPRAY valve down to the
PRIME position.
lse
Pu ean
Cl
Motor Running
Max PSI
(Bar)
Pressure Indicator
The pressure indicator shows the current operating pressure of
the sprayer. It has three different indications: blinking yellow,
solid yellow, and solid green.
Blinking Yellow
When the pressure indicator is blinking yellow, the sprayer is
operating between 0 and 200 PSI. A blinking yellow pressure
indicator means:
• The sprayer is plugged in and turned “ON”
• The sprayer is at priming pressure (little or no pressure)
• It is safe to move the PRIME/SPRAY valve between
positions
• It is safe to change or replace the spray tip
NOTE: If the pressure indicator begins blinking yellow
when the pressure control knob is set at a higher
pressure and the PRIME/SPRAY valve is in the
SPRAY position, either the spray tip is worn or
the sprayer is in need of service/repair.
Xact Digital Control System Operation (if
equipped)
The Xact Digital Control System is an optional add-on that
increases the functionality of the sprayer. It is installed directly
below the pressure control knob on the control panel. It consists
of a display and four function keys. The display shows various
menu screens that allow the user to customize and monitor
sprayer operation using the function keys.
Solid Yellow
When the pressure indicator is solid yellow, the sprayer is
operating between 201 and 1900 PSI. A solid yellow pressure
indicator means:
• The sprayer is at the proper pressure setting for spraying
stain, lacquer, varnish, and multi-colors
• If the pressure indicator goes to solid yellow when the
pressure is set so that it starts at solid green, it indicates
one of the following:
a. Tip Wear Indicator — when spraying with latex or at
high pressure the solid yellow appears. This means the
tip is worn and needs to be replaced.
b. Tip Too Large — when a tip that is too large for the
sprayer is put in the gun, the pressure indicator will turn
from solid green to solid yellow.
c. Fluid Section Wear — if a solid yellow pressure
indicator appears when using a new tip and the pressure
is set at maximum, service may be required (worn
packings, worn piston, stuck valve, etc...).
Display
Function
Keys
MENU
1
+
2
3000
2950
–
3
SELECT
4
NOTE: The pressure control knob overrides the Xact
Digital Control System settings. Anytime the
pressure control knob is turned, the sprayer
pressure will change accordingly.
Function Keys
Solid Green
When the pressure indicator is solid green, the sprayer is
operating between 1901 and 3300 PSI. A solid green pressure
indicator means:
• The sprayer is at the proper pressure setting for spraying
oil-based and latex house paints
• The sprayer is operating at peak performance at a high
pressure setting
The function keys are numbered 1–4. Each key is labeled with
an additional function as well.
#1/Menu Key
Pressing the #1 key scrolls through the available menu screens
or performs a function described on the active menu screen.
#2/+ Key
Pressing the #2 key performs a function described on the active
menu screen or increases a value.
#3/- Key
Pressing the #3 key performs a function described on the active
menu screen or decrease a value.
#4/Select Key
Pressing the #4 key selects the active menu screen or performs
a function described on the active menu screen.
Motor Running Indicator
The Motor Running indicator is on when the motor is commanded
to run. This indicator is used by service centers to troubleshoot
motor problems.
SET PSI
ACTUAL PSI
6
© Titan Tool Inc. All rights reserved.
Menu Screens
The Service Time screen allows the user to set a service time
interval (in hours). Below the set time, the screens shows the
current amount of hours on the sprayer. To select the Service
Timer screen, press the #4 key.
SERVICE @
XXXHR
The screen will toggle between the
RUN HOURS
XX
service hours and a screen that allows
the user to change the service time interval.
When the service time interval is set and met by the run hours,
the display will toggle between the “Main screen” and a “Service
Required” screen at sprayer startup.  To stop the toggling, scroll
to the “Service Time” screen and either set a new service time
interval or set the service time to “0”.
Several menu screens are available for the user to customize
and monitor sprayer operation. They include Main Screen, User
Pre-Sets, Volume Pumped, Job Volume, Unit Serial #, TImers,
Job Timers, Service Time, Pressure, Security Code, Prime, and
Pulse Clean.
Main Screen
SET PSI
3000
The Main Screen is the default screen
2950
for the control system at sprayer startup. ACTUAL PSI
Pressing the #2 key switches between PSI and MPa units of
measure. Press the #1 key to scroll through the remaining menu
screens.
Pressure Screen
PRESSURE
The Pressure screen allows the user to
SELECT-4
MENU-1
see the current set point pressure as
well as the actual working pressure.
SET PSI
3000
To select the Pressure screen, press
2950
the #4 key. This screen is also the Main ACTUAL PSI
Screen.
User Pre-Sets Screen
USER PRE-SETS
The User Pre-Sets screen allows the
SELECT-4
MENU-1
user to set four different pressure
settings and save them for future use. To select the User PreSets screen, press the #4 key.
SELECT
Press keys 1 through 4 from the Select
PRE-SETS 1-4
screen to select or change a pre-set
pressure.
PSI SETTING
750
Press the #4 key to select the setting
SELECT-4
CHG-2
and the Main Screen will appear.
750
Press the #2 key to change the setting. PRE-SET #1
PRESS +/- TO CHG
On the following screen, use the #2/+
key to increase the setting or the #3/- screen to decrease the
setting. Once the desired setting has been reached, press the #4
key to set and the Main Screen will appear. To select or change
the remaining three pre-sets, scroll to the User Pre-Sets screen
and repeat the above procedure.
Volume Pumped Screen
The Volume Pumped screen shows the
total number of gallons or liters sprayed
by the sprayer.
To select the Volume Pumped screen,
press the #4 key.
Job Volume Screen
The Job Volume screen allows the user
to reset a gallon counter to track usage
on specific jobs.
To select the Job Volume screen, press
the #4 key.
Unit Serial # Screen
The Unit Serial # screen shows the
sprayers serial number.
To select the Unit Serial # screen, press
the #4 key.
Timers Screen
Security Code Screen
SECURITY CODE
The Security Code screen allows the
SELECT-4
MENU-1
user to set a four digit security code
to prevent unauthorized use of the sprayer. If a security code
has been set, the control system display will ask for the code at
startup. If the correct code is entered, the display will show the
Main Screen and the sprayer will operate. If the wrong code is
entered, the display will continue to ask for the correct code and
the sprayer will be disabled. To set or change the security code,
press the #2 key.
NOTE: If the sprayer is new, no security code is set and
the Main Screen will appear at startup. Also,
when setting a security code for the first time, the
“Enter Old Code Number” screen will not appear.
VOLUME PUMPED
SELECT-4
MENU-1
GALLONS XXXXXX
PRESS 1 FOR MENU
ENTER OLD CODE
Enter the old security code number to
NUMBER
access the screen that allows the code
change. If the wrong code is entered, the display will continue to
ask for the correct code and the security code cannot be changed.
ENTER NEW CODE
Enter the new security code. Once the
NUMBER
new code is entered, the display will
automatically ask that the new code be re-entered for verification.
If the same new code is re-entered, the display will confirm that
the new code has been accepted and return to the Main Screen.
If the new code is re-entered incorrectly, the display will return to
the “Enter New Code Number” screen and the process will repeat.
JOB VOLUME
SELECT-4
MENU-1
JOB GALLONS
XXXX
MENU-1
RESET-3
UNIT SERIAL #
SELECT-4
MENU-1
SER # XXXXXXXXXX
PRESS 1 FOR MENU
NOTE: To inactivate the X-Lock security function, enter
“1111” at the “Enter New Code Number” screen
(this is the default code that leaves the sprayer
unlocked). As a result, the Main Screen will
appear at sprayer startup.
TIMERS
The Timers screen shows the total time SELECT-4
MENU-1
the sprayer has been turned on as well
as the total time the sprayer has been running (pumping).
ON TIME XXXXX:XX
To select the Timers screen, press the
RUN TIME XXXX:XX
#4 key.
Prime Screen
PRIME
The Prime screen appears when the
pressure control knob is set at the “Min”
setting in the yellow zone.
Pulse Clean Screen
PULSE CLEAN
The Pulse Clean screen appears when
ACTUAL PSI
XXXX
the pressure control knob is set at the
PULSE CLEAN position in the red zone and the PRIME/SPRAY
valve is in the PRIME position.
Job Timers Screen
JOB TIMERS
The Job Timers screen allows the user
MENU-1
to reset the “ON TIME” and “RUN TIME” SELECT-4
to track time on specific jobs.
To select the Job TImers screen, press ON TIME XXXXX:XX
RUN TIME XXXX:XX
the #4 key. The screen will toggle
between the timers and a screen that allows the user to reset the
timers.
Service Time Screen
The Job Volume screen allows the user
to reset a gallon counter to track usage
on specific jobs.
© Titan Tool Inc. All rights reserved.
NOTE: If there is no action at any menu screen for 30
seconds, the display will go back to the Main
Screen.
SERVICE TIME
SELECT-4
MENU-1
7
Paint Spraying Technique
Overlap edges
POSSIBLE INJECTION HAZARD. Do not spray
without the tip guard in place. Never trigger the
gun unless the tip is in either the spray or the
unclog position. Always engage the gun trigger
lock before removing, replacing, or cleaning tip.
The following techniques, if followed, will assure professional
painting results.
NOTE: Modified spraying techniques may be necessary
when spraying textured products. This may
include adjustment to gun position, spraying
distance, and pressure settings as well as the
addition of a splatter nozzle.
Hold the gun perpendicular to the surface and always at equal
distance from the surface. Depending on the type of material,
surface, or desired spray pattern, the gun should be held at a
distance of 12 to 14 inches (30 to 35 cm).
1st
pass
Move the gun either across or up and down the surface at a
steady rate. Moving the gun at a consistent speed conserves
material and provides even coverage. The correct spraying
speed allows a full, wet coat of material to be applied without
runs or sags.
Maintain uniform spray stroke action. Spray alternately from left
to right and right to left. Begin movement of the gun before the
trigger is pulled.
pull
trigger
release
trigger
end
stroke
4th
pass
5th
pass
Practice
1. Make sure that the spray hose is free of kinks and clear of
objects with sharp cutting edges.
2. Set the pressure to minimum by turning the pressure
control knob to the “Min” setting in the yellow zone.
3. Move the PRIME/SPRAY valve up to its SPRAY position.
4. Turn the pressure control knob clockwise to its highest
setting in the green zone. The spray hose should stiffen
as material begins to flow through it.
5. Unlock the gun trigger lock.
6. Trigger the spray gun to bleed air out of the hose.
7. When material reaches the spray tip, spray a test area to
check the spray pattern.
8. Use the lowest pressure setting
necessary to get a good spray
pattern. If the pressure is set
Good spray pattern
too high, the spray pattern will
be too light. If the pressure is
set too low, tailing will appear
or the paint will spatter out in
gobs rather than in a fine spray.
Paint tailing pattern
Avoid arcing or holding the gun at an angle. This will result in an
uneven finish.
Offspray
Too Thick
Arcing
3rd
pass
For corners and edges, split the
center of the spray pattern on
the corner or edge and spray
vertically so that both adjoining
sections receive approximately
even amounts of paint.
When spraying with a shield,
hold it firmly against the surface. Angle the spray gun slightly
away from the shield and toward the surface. This will prevent
paint from being forced underneath.
Shrubs next to houses should be tied back and covered with a
canvas cloth. The cloth should be removed as soon as possible.
Titan gun extensions are extremely helpful in these situations.
Nearby objects such as automobiles, outdoor furniture, etc.
should be moved or covered whenever in the vicinity of a spray
job. Be careful of any other surrounding objects that could be
damaged by overspray.
Holding the gun closer to the surface deposits more material on
the surface and produces a narrower spray pattern. Holding the
gun farther from the surface produces a thinner coat and wider
spray pattern. If runs, sags, or excessive material occur, change
to a spray tip with a smaller orifice. If there is an insufficient
amount of material on the surface or you desire to spray faster, a
larger orifice tip should be selected.
start
stroke
2nd
pass
Gun at angle
Proper lapping (overlap of spray pattern) is essential to an even
finish. Lap each stroke. If you are spraying horizontally, aim
at the bottom edge of the preceding stroke, so as to lap the
previous pattern by 50%.
8
© Titan Tool Inc. All rights reserved.
Cleanup
Cleaning the Inlet Screen
The inlet screen will clog and must be
cleaned at least once a day.
1. Remove the retaining ring from the
foot valve housing
2. Remove the inlet screen from the
Foot valve housing.
3. Clean thoroughly with the
appropriate solvent.
Special cleanup instructions for use with
flammable solvents:
• Always flush spray gun preferably outside and at least one
hose length from spray pump.
• If collecting flushed solvents in a one gallon metal container,
place it into an empty five gallon container, then flush solvents.
• Area must be free of flammable vapors.
• Follow all cleanup instructions.
Important: The sprayer, hose, and gun should be cleaned
thoroughly after daily use. Failure to do so permits material
to build up, seriously affecting the performance of the unit.
1.
2.
3.
4.
5.
Inlet Screen
Retaining
Ring
Maintenance
Always spray at minimum pressure with the gun
nozzle tip removed when using mineral spirits or
any other solvent to clean the sprayer, hose, or
gun. Static electricity buildup may result in a fire
or explosion in the presence of flammable vapors.
Follow the “Pressure Relief Procedure” found in the
Operation section of this manual.
Remove the gun tip and tip guard and clean with a brush
using the appropriate solvent.
Place the foot valve into a container of the appropriate
solvent (refer to recommendations of the material
manufacturer). An example of an appropriate solvent is
water for latex paint.
Place the return hose into a metal waste container.
Move the PRIME/SPRAY valve down to its
PRIME position.
Before proceeding, follow the Pressure Relief
Procedure outlined previously in this manual.
Additionally, follow all other warnings to reduce
the risk of an injection injury, injury from moving
parts or electric shock. Always unplug the sprayer
before servicing!
General Repair and Service Notes
The following tools are needed when repairing this sprayer:
Phillips Screwdriver
3/8” Hex Wrench
Needle Nose Pliers
5/16” Hex Wrench
Adjustable Wrench
1/4” Hex Wrench
Rubber Mallet
3/16” Hex Wrench
Flat-blade Screwdriver
5/32” Hex Wrench
NOTE:Hold the return hose in the waste
container when moving the
PRIME/SPRAY valve to PRIME in
case the sprayer is pressurized.
1. Before repairing any part of the sprayer, read the
instructions carefully, including all warnings.
Important: Never pull on a wire to disconnect it. Pulling
on a wire could loosen the connector from the wire.
2. Test your repair before regular operation of the sprayer
to be sure that the problem is corrected. If the sprayer
does not operate properly, review the repair procedure
to determine if everything was done correctly. Refer to
the Troubleshooting Charts to help identify other possible
problems.
3. Make certain that the service area is well ventilated in
case solvents are used during cleaning. Always wear
protective eyewear while servicing. Additional protective
equipment may be required depending on the type of
cleaning solvent. Always contact the supplier of solvents
for recommendations.
4. If you have any further questions concerning your Titan
Airless Sprayer, call Titan:
Customer Service (U.S.)........................ 1-800-526-5362
Fax ................................................ 1-800-528-4826
Customer Service (Canada).................. 1-800-565-8665
Fax.................................................. 1-905-856-8496
6. Set the pressure to Turbo PulseClean by
turning the pressure control knob to its
PULSE CLEAN position in the red zone.
7. Turn on the sprayer by moving the ON/OFF
switch to the ON position.
8. Allow the solvent to circulate through the unit and flush the
paint out of the return hose into the metal waste container.
9. Turn off the sprayer by moving the ON/
OFF switch to the OFF position.
10. Move the PRIME/SPRAY valve up to its
SPRAY position.
11. Turn on the sprayer.
Ground the gun by holding it
against the edge of the metal
container while flushing. Failure to
do so may lead to a static electric
discharge, which may cause a fire.
12. Trigger the gun into the metal waste container until the
paint is flushed out of the hose and solvent is coming out
of the gun.
13. Continue to trigger the spray gun into the waste container
until the solvent coming out of the gun is clean.
Min PSI
(Bar)
lse
Pu an
Cle
Max PSI
(Bar)
NOTE: For long-term or cold weather storage, pump
mineral sprits through the entire system.
For short-term storage when using latex paint,
pump water mixed with Titan Liquid Shield
through the entire system (see the Accessories
section of this manual for part number).
14. Follow the “Pressure Relief Procedure” found in the
Operation section of this manual.
15. Unplug the unit and store in a clean, dry area.
Important: Do not store the unit under pressure.
© Titan Tool Inc. All rights reserved.
Foot Valve
Housing
9
Replacing the Motor Assembly
Replacing the Gears
1. Perform the Pressure Relief Procedure and unplug the
sprayer.
2. Loosen and remove the four motor shroud screws.
Remove the motor shroud.
3. Release the tie wrap on the top of the baffle assembly and
slip the baffle assembly down off of the motor.
4. Loosen and remove the three electronic cover screws. Lift
the electronic cover off of the electronic control assembly
on the motor.
5. Disconnect all wires between the motor and the sprayer.
6. Loosen and remove the three motor mounting screws.
7. Pull the motor out of the gearbox housing.
8. With the motor removed, inspect the gears in the gearbox
housing for damage or excessive wear. Replace the
gears, if necessary.
9. Install the new motor into the gearbox housing. Make sure
the housing gasket is positioned properly.
10. Secure the motor with the three motor mounting screws.
11. Reconnect the wires between the sprayer and the new
motor. (refer to the electrical schematic in the Parts List
section of this manual).
12. Position the electronic cover over the electronic control
assembly. Secure the electronic cover with the three
electronic cover screws.
13. Slip the baffle assembly up and around the motor. Secure
the baffle assembly with the tie wrap.
14. Slide the motor shroud over the motor. Make sure the
shroud gasket is positioned properly.
15. Secure the motor shroud with the four motor shroud
screws.
1. Perform the Pressure Relief Procedure and unplug the
sprayer.
2. Loosen and remove the four motor shroud screws.
Remove the motor shroud.
3. Release the tie wrap on the top of the baffle assembly and
slip the baffle assembly down off of the motor.
4. Loosen and remove the three electronic cover screws. Lift
the electronic cover off of the electronic control assembly
on the motor.
5. Disconnect all wires between the motor and the sprayer.
6. Loosen and remove the three motor mounting screws.
7. Pull the motor out of the gearbox housing.
8. Inspect the armature gear on the end of the motor for
damage or excessive wear. If this gear is completely worn
out, replace the front end bell assembly.
9. Remove and inspect the 1st stage gear and 2nd stage
gear assemblies for damage or excessive wear. Replace,
if necessary.
10. Remove and inspect the front gear box assembly for
damage or excessive wear. If damaged or worn, replace
the front gear box assembly.
NOTE: Clean and refill the gear box cavity up to the rear
face of each gear with Lubriplate (P/N 314-171).
11. Install the motor into the gearbox housing. Make sure the
housing gasket is positioned properly.
12. Secure the motor with the three motor mounting screws.
13. Reconnect the wires between the sprayer and the motor.
(refer to the electrical schematic in the Parts List section
of this manual).
14. Position the electronic cover over the electronic control
assembly. Secure the electronic cover with the three
electronic cover screws.
15. Slip the baffle assembly up and around the motor. Secure the baffle assembly with the tie wrap.
16. Slide the motor shroud over the motor. Make sure the
shroud gasket is positioned properly.
17. Secure the motor shroud with the four motor shroud
screws.
Motor Shroud Screws
Motor Shroud
Electronic Cover
Electronic Cover
Screw
Gearbox
Housing
Motor Mounting
Screw
Front End Bell
Assembly
Electronic Control
Assembly
Armature Gear
Motor
1st Stage Gear
2nd Stage Gear
Baffle Assembly
Housing Gasket
Shroud Gasket
Front Gear Box
Assembly
Housing
Gasket
Shroud
Gasket
10
© Titan Tool Inc. All rights reserved.
Replacing the Transducer
Replacing the prime/spray Valve
1. Perform the Pressure Relief Procedure and unplug the
sprayer.
2. Loosen and remove the four motor shroud screws.
Remove the motor shroud.
3. At the electronic control assembly, disconnect the wire
coming from the transducer.
4. Pull the grommet out of the mounting plate and slide it up
the shaft of the transducer until it is clear of the mounting
plate.
5. Using a wrench, loosen and remove the transducer from
the filter housing. Carefully thread the transducer wire out
through the mounting plate.
6. Slide the grommet off of the old transducer and onto the
new transducer.
7. Thread the new transducer wire through the mounting
plate and up to the electronic control assembly.
8. Thread the new transducer into the filter housing and
tighten securely with a wrench.
Perform the following procedure using PRIME/SPRAY valve
replacement kit P/N 800-915.
1. Push the groove pin out of the valve handle.
2. Remove the valve handle and the cam base.
3. Using a wrench, loosen and remove the valve housing
assembly.
4. Make sure the gasket is in place and thread the new valve
housing assembly into the filter block. Tighten securely
with a wrench.
5. Place the cam base over the valve housing assembly.
Lubricate the cam base with grease and line up the cam
with the filter block using the dowel pin.
6. Line up the hole on the valve stem with the hole in the
valve handle.
7. Insert the groove pin into the valve handle and through the
valve stem to secure the valve handle in position.
Gasket
NOTE: Make sure the o-ring on the transducer is in
place before threading the transducer into the
filter housing.
Valve Housing
Assembly
Cam Base
Valve
Handle
Motor Shroud Screws
Electronic Control
Assembly
Motor Shroud
Grommet
Transducer
Mounting Plate
© Titan Tool Inc. All rights reserved.
To
F
Filter
Housing
Dowel Pin
9. Push the grommet into the mounting plate.
10. Connect the transducer wire to the electronic control
assembly (refer to the electrical schematic in the Parts List
section of this manual).
11. Slide the motor shroud over the motor. Make sure the
shroud gasket is positioned properly.
12. Secure the motor shroud with the four motor shroud
screws.
ilte
r
11
Valve Stem
Groove Pin
Servicing the Fluid Section
NOTE: During reassembly, make sure the Viton o-rings
and the Teflon back-up rings between the upper
housing and lower housing as well as between
the lower housing and the foot valve housing
are lubricated with grease and in position.
Use the following procedures to service the valves and repack
the fluid section. Perform the following steps before performing
any maintenance on the fluid section.
1. Loosen and remove the four front cover screws. Remove
the front cover.
2. Position the crankshaft/slider assembly at the bottom,
dead-center of its stroke so that the connecting pin and
retaining ring are visible below the slider assembly. This
is done by turning the sprayer on and off in short bursts
until the connecting pin is visible below the slider housing.
3. Turn off and unplug the sprayer.
Repacking the Fluid Section
1. Remove the foot valve assembly
and the lower housing using
the steps in the “Servicing the
Valves” procedure above.
NOTE: The outlet valve does not
need to be disassembled
from the piston rod for
this procedure.
Before proceeding, follow the Pressure Relief
Procedure outlined previously in this manual.
Additionally, follow all other warnings to reduce
the risk of an injection injury, injury from moving
parts or electric shock. Always unplug the sprayer
before servicing!
2. Turn the upper housing
counterclockwise to loosen it
from the cylinder.
3. Slowly pull down the upper
housing just far enough to
expose the extension slider and
the connecting pin that connects
the piston rod to the extension
slider.
4. Push the connecting pin out of
the extension slider and piston
rod and remove the piston rod/
upper housing.
5. Place the upper housing upright
in a vise by clamping on the
wrench flats.
4. Remove the return hose from the hose clamp on the fluid
section.
5. Loosen and remove the high-pressure hose from the fitting
on the upper housing of the fluid section.
Upper
Housing
The design of the fluid section allows
Lower
access to the foot valve and seat
Housing
as well as the outlet valve and seat
without completely disassembling the
Foot Valve
fluid section. It is possible that the
Cage
valves may not seat properly because
Foot Valve
of debris stuck in the foot valve seat
Ball
or outlet valve seat. Use the following
instructions to clean the valves and
Foot Valve
reverse or replace the seats.
Seat
1. Loosen and remove the foot
O-ring
valve housing from the lower
Viton
housing.
O-Ring
2. Clean out any debris in the foot
Teflon
valve housing and examine the
Back-Up
housing and the foot valve seat.
Ring
If the seat is damaged, reverse
or replace the seat.
Foot Valve
Housing
3. Using two wrenches, hold the
upper housing at the wrench
flats with one wrench and loosen the lower housing with
the other. Remove the lower housing.
4. Using a 3/4” wrench, loosen and remove the outlet valve
retainer from the piston rod.
Upper
Housing
NOTE:Always service the outlet
valve with the piston rod
Piston Rod
attached to the pump.
Outlet Valve
This will prevent the
Seal
piston rod from rotating
during disassembly of
Outlet Valve
Cage
the outlet valve.
Outlet Valve
5. Clean out any debris and examine
Ball
the retainer and outlet valve seat.
Nylon
If the seat is damaged, reverse or
Washer
replace the seat.
Outlet Valve
6. Remove, clean, and inspect the
Seat
outlet valve cage and outlet valve
Outlet Valve
ball. Replace if they are worn or
Retainer
damaged.
Lower
7. Reassemble the valves by
Housing
reversing the steps above.
Servicing the Valves
NOTE: Do not over-tighten the
vise. Damage to the
upper housing may
occur.
Cylinder
Extension
Slider
Connecting
Pin
Upper Seal
Retainer
Spacer
Upper
Packing
Upper
Housing
Lower
Packing
Wear Ring
Piston Rod
6. Using a wrench, remove the
upper seal retainer.
7. Slide the piston rod out through
the bottom of the upper housing.
8. Inspect the piston rod for wear
and replace if necessary.
9. Remove the upper and lower packings from the upper
housing.
NOTE: Be careful not to scratch, score, or otherwise
damage the upper housing during removal of
the packings.
10. Clean the upper housing. Inspect the upper housing for
damage and replace if necessary.
11. Locate the new upper and lower packings and pack the
areas between the packing lips with grease. Lubricate the
o-rings on the exterior of the packings with grease.
Install upper packing
12. Insert the upper packing into the
with raised lip
top of the upper housing with the
facing down.
raised lip on the packing facing
down.
13. Insert the spacer on top of the
upper packing.
Raised Lip
14. Thread the upper seal retainer
into the upper housing and torque
to 25-30 ft. lbs.
15. Pre-form the lower packing using the lower packing sizing
tool (included in the repacking kit).
12
© Titan Tool Inc. All rights reserved.
Replacing the Filters
16. Insert the lower packing partially Install lower packing with
the side that has the o-ring
into the bottom of the upper
housing so that the side that has closest to the face of the
packing facing up.
the o-ring closest to the face of
the packing faces up.
Closer
17. Push the lower packing into
position using the lower packing
Top
insertion tool (see Fluid Section
Assembly parts list for lower
packing insertion tool P/N).
18. Place the piston insertion tool (included in the repacking kit)
over the top of the piston rod.
19. Insert the piston rod into the bottom of the upper housing,
through the lower packing, through the upper packing, and
out through the upper seal retainer.
Gun Filter
1. Pull the bottom of the trigger guard forward so that it
comes loose from the handle assembly.
2. Loosen and remove the handle assembly from the gun
head.
3. Pull the old filter out of the gun head.
4. Slide the new filter, tapered end first, into the gun head.
5. Make sure all the parts are clean and the handle seal is in
position inside the gun head.
6. Thread the handle assembly into the gun head until
secure.
7. Snap the trigger guard back onto the handle assembly.
NOTE: When repacking the fluid section, make sure the
raised lip on the bottom of the lower packing is
fully outside the packing around the piston rod
after insertion of the piston rod.
20. Remove the piston insertion tool from the top of the piston
rod.
21. Lubricate the threads on the upper housing with anti-seize
compound. Remove the upper housing from the vise.
22. Insert the piston rod into the extension slider. When the
connecting pin hole on the piston rod lines up with the hole
in the extension slider, insert the connecting pin.
23. Thread the upper housing into the cylinder, turning
clockwise.
24. Continue to turn the upper housing clockwise until it is
flush against the cylinder.
Trigger
Guard
Handle
Seal
Filter
Handle
NOTE: If the fitting on the upper housing does not face
the tool box side of the unit, turn the upper
housing counterclockwise until the nipple
faces the tool box side of the unit. Do not
turn the upper housing more than one full turn
counterclockwise.
25. Making sure that the Viton o-ring and Teflon back-up ring
are lubricated and in place, thread the lower housing into
the upper housing. Using two wrenches, hold the upper
housing at the wrench flats with one wrench and tighten
the lower housing with the other.
26. Attach the high-pressure hose to the fitting on the upper
housing and tighten with a wrench. Do not kink the hose.
27. Making sure that the Viton o-ring and Teflon back-up
ring are lubricated and in place, reassemble the foot
valve assembly and and thread it into the lower housing.
Tighten securely.
28. Replace the return hose into the clamp on the siphon tube.
29. Place the front cover on the gearbox housing and secure
in position using the four front cover screws.
30. Turn on the sprayer by following the procedure in the
“Operation” section of this manual and check for leaks.
NOTE: For more detail, part number information, and
complete assembly drawings, refer to the S-3
Airless Spray Gun Owner’s Manual (P/N 3132440).
Pump Filter
1. Loosen and remove the filter
body by hand.
2. Slip the filter off of the core
spring.
3. Inspect the filter. Based on
inspection, clean or replace
the filter.
4. Inspect the o-ring. Based on
inspection, clean or replace
the o-ring.
5. Slide the new or cleaned filter
over the core spring with the
filter spring adapter in place.
Push the filter into the center
of the filter housing.
6. Slide the filter body over the
filter and thread it into the filter
housing until secure.
NOTE: Repacking kit P/N 800-273 is available. For best
results use all parts supplied in this kit.
NOTE: The filter body should
be hand-tightened,
but make sure it is
seated fully into the
filter housing.
© Titan Tool Inc. All rights reserved.
Gun
Head
13
Filter Body
Filter Spring
Filter
Filter Spring
Adapter
Core Spring
O-ring
Filter Housing
Troubleshooting
Problem
A. The unit will not run.
B. The unit will not prime.
Cause
Solution
1. Plug the unit in.
2. Reset the breaker.
3. Turn the pressure control knob clockwise to supply
power to the unit and increase the pressure setting.
4. Inspect or take to a Titan authorized service center.
5. Allow motor to cool.
6. Replace the ON/OFF switch.
C. The unit will not build or
maintain pressure.
1. The spray tip is worn.
2. The spray tip is too large.
3. The pressure control knob is not set
properly.
4. The pump filter, gun filter, or inlet screen is clogged.
7. There is external fluid leak.
8. There is an internal fluid section leak
(packings are worn and/or dirty, valve balls
are worn).
9. Worn valve seats
E. Excessive surge at the spray
gun.
F. Poor spray pattern.
G. The unit lacks power.
5. Material flows from the return hose when
the PRIME/SPRAY valve is in the SPRAY
position.
6. Air leak in the siphon tube/siphon
assembly.
1. The PRIME/SPRAY valve is in the SPRAY position.
2. Air leak in the siphon tube/siphon
assembly.
3. The pump filter and/or inlet screen is
clogged.
4. The siphon tube/siphon assembly is
clogged.
D. Fluid leakage at the upper end
of the fluid section.
1. The unit is not plugged in.
2. Tripped breaker.
3. The pressure is set too low (pressure
control knob set at minimum setting does
not supply power to unit).
4. Faulty or loose wiring.
5. Excessive motor temperature.
6. ON/OFF switch is defective.
10. Motor powers but fails to rotate
1. The upper packings are worn.
2. The piston rod is worn.
1. Wrong type of airless spray hose.
2. The spray tip worn or too large.
3. Excessive pressure.
1. The spray tip is too large for the material
being used.
2. Incorrect pressure setting.
3. Insufficient fluid delivery.
4. The material being sprayed is too viscous. 1. The pressure adjustment is too low.
2. Improper voltage supply.
14
1. Rotate the PRIME/SPRAY valve clockwise to the
PRIME position.
2. Check the siphon tube/siphon assembly connection
and tighten or re-tape the connection with Teflon
tape.
3. Remove the pump filter element and clean. Remove
the inlet screen and clean.
4. Remove the siphon tube/siphon assembly and clean.
1. Replace the spray tip following the instructions that
came with the spray gun.
2. Replace the spray tip with a tip that has a smaller
orifice following the instructions that came with the
spray gun.
3. Turn the pressure control knob clockwise to increase
the pressure setting.
4. Remove the pump filter element and clean. Remove
the gun filter and clean. Remove the inlet screen
and clean.
5. Clean or replace the PRIME/SPRAY valve.
6. Check the siphon tube/siphon assembly connection
and tighten or re-tape the connection with Teflon
tape.
7. Check for external leaks at all connections. Tighten
connections, if necessary.
8. Clean the valves and service the fluid section
following the “Servicing the Fluid Section” procedure
in the Maintenance section of this manual.
9. Reverse or replace the valve seats following the
“Servicing the Fluid Section” procedure in the
Maintenance section of this manual.
10. Take unit to a Titan authorized service center.
1. Repack the pump following the “Servicing the Fluid
Section” procedure in the Maintenance section of this
manual.
2. Replace the piston rod following the “Servicing the
Fluid Section” procedure in the Maintenance section
of this manual.
1. Replace hose with a minimum of 50’ of 1/4”
grounded textile braid airless paint spray hose.
2. Replace the spray tip following the instructions that
came with the spray gun.
3. Rotate the pressure control knob counterclockwise to
decrease spray pressure.
1. Replace the spray tip with a new or smaller spray tip
following the instructions that came with the spray
gun.
2. Rotate the pressure control knob to adjust the
pressure for a proper spray pattern.
3. Clean all screens and filters.
4. Add solvent to the material according to the
manufacturer’s recommendations.
1. Rotate the pressure control knob clockwise to
increase the pressure setting.
2. Reconnect the input voltage for 120V AC.
© Titan Tool Inc. All rights reserved.
Xact Digital Control System Error
Messages
High Control Temperature Screen (E6)
HIGH CONTROL
The High Control Temperature screen
TEMPERATURE
appears when the temperature of the
Xact Digital Control System has risen too high. Take the sprayer
to a Titan authorized service center for repair.
The following error message screens appear whenever the Xact
Digital Control System detects a problem with the sprayer. Once
a problem occurs and the error message appears, the sprayer
will shut down.
High Load Check Mechanism Screen (E7)
HIGH LOAD
The High Load Check Mechanism
CHECK MECHANISM
screen appears when the sprayer shuts
down because of high current or when the sprayer goes into
current fold back mode.. Take the sprayer to a Titan authorized
service center for repair.
Before proceeding, follow the Pressure Relief
Procedure outlined previously in this manual.
Additionally, follow all other warnings to reduce the
risk of an injection injury, injury from moving parts
or electric shock. Always unplug the sprayer
before servicing!
Exceeded Pressure Limit Screen (E8)
Check Paint Screen (E1)
EXCEEDED
The Exceeded Pressure Limit screen
PRESSURE LIMIT
appears when the sprayer pressure
exceeds 3300 PSI / 22.8 MPa. Take the sprayer to a Titan
authorized service center for repair.
CHECK PAINT
The Check Paint screen appears when
the pump pressure drops to a very
low level and the pressure control knob has not been adjusted.
Check the paint level and refill. Restart the sprayer by following
the “Painting” procedure in the Operation section of this manual.
Communication Error Screen (E9)
COMMUNICATION
The Communication Error screen
ERROR
appears when the Xact Digital Control
System loses communication with the control panel. Take the
sprayer to a Titan authorized service center for repair.
Check Transducer Screen (E2)
CHECK TRANSDUCER
The Check Transducer screen appears
when the transducer has become
disconnected or is defective. Take the sprayer to a Titan
authorized service center for repair.
Check Motor Screen (E3)
CHECK MOTOR
The Check Motor screen appears when
the motor or motor sensor is defective.
Take the sprayer to a Titan authorized service center for repair.
Low Voltage Screen (E4)
LOW VOLTAGE
The Low Voltage screen appears when
the sprayer shuts down because of low
input voltage. Check the power supply and correct the problem.
Restart the sprayer by following the “Painting” procedure in the
Operation section of this manual.
High Motor Temperature Screen (E5)
HIGH MOTOR
The High Motor Temperature screen
TEMPERATURE
appears when the temperature of the
motor has risen too high. Take the sprayer to a Titan authorized
service center for repair.
© Titan Tool Inc. All rights reserved.
15
Consignes de sécurite important ·
Lire toutes ces consignes avant
d’utiliser l’appareil. Garder ces consignes.
DANGER : ÉMANATIONS DANGEREUSES
Certains produits (peintures, solvants, insecticides ou
autres) peuvent être nocifs s’ils sont inhalés ou entrent en
contact avec l’organisme. Les émanations de ces produits
peuvent provoquer de graves nausées, évanouissements
ou empoisonnements.
Indique une situation à risque, laquelle, si elle n’est pas
évitée, peut entraîner des blessures graves, voire la mort.
Pour réduire les risques d’incendie ou d’explosion, de
choc électrique et de blessure, vous devez lire et
comprendre les directives figurant dans ce manuel.
Familiarisez-vous avec les commandes et l’utilisation
adéquate de l’équipement.
MESURES PRÉVENTIVES :
• Se servir d’un masque ou d’un respirateur s’il
y a risque d’inhalation (lire toutes les directives
concernant ces dispositifs afin de s’assurer qu’ils
offrent la protection requise).
• Porter des lunettes de protection.
• Porter les vêtements de protection prescrits par le fabricant du
produit utilisé.
Danger : injection cutanée
A high pressure paint stream produced by this Le jet de
haute pression produit par cet appareil peut transpercer
la peau et les tissus sous-jacents, causant des blessures
graves pouvant entraîner l’amputation.
NE PAS TRAITER ce type de BLESSURE COMME
UNE SIMPLE COUPURE! Une amputation peut en résulter. ON doit
consulter un médicin sur-le-champ.
La pression maximale de ce pulvérisateur est d’environ 3 300 PSI / 22,8
MPa.
mesures PRÉVENtives :
• Ne pas pointer le pistolet vers une partie du corps.
• Ne pas pointer le pistolet vers une personne ou un animal; ne pas
pulvériser non plus de produit dessus.
• NE JAMAIS mettre une partie du corps devant le jet de produit.
NE JAMAIS toucher les fuites du flexible de pulvérisation.
• NE JAMAIS mettre la main, même gantée, devant le pistolet (les
gants n’offrent aucune protection contre les blessures par injection).
• TOUJOURS verrouiller la détente, arrêter la pompe et relâcher
toute la pression avant d’effectuer la maintenance de l’appareil ou
de le laisser sans surveillance, d’en nettoyer le protège-embout
ou l’embout, ou de remplacer ce dernier. La pression ne sera
pas relâchée par le simple arrêt du moteur; pour ce faire, on
doit se servir du bouton PRIME/SPRAY (se reporter à la section
Comment libérer la pression, du présent manuel).
• TOUJOURS s’assurer que le protège-embout est en place
avant de pulvériser. Il est cependant à noter que, s’il assure une
certaine protection, ce dispositif joue surtout un rôle préventif.
• TOUJOURS retirer l’embout avant de vidanger ou de nettoyer
l’appareil.
• toujours inspecter le flexible avant de commencer; celui-ci
peut présenter des fuites attribuables à l’usure, à une flexion
excessibe ou à un traitement abusif, lesquelles fuites présentent
des risques d’injection cutanée. Ne pas utiliser le flexible pour
soulever ou tirer l’équipement.
• NE JAMAIS utiliser de pistolet sans verrou de détente et protègedoigts.
• Tous les accessoires (pistolets, embouts, rallonges, flexibles etc.)
doivent pouvoir subir une pression nominale de 3 300 PSI / 22,8
MPa ou plus.
• Ne laissez pas l’appareil sous tension ou sous pression quand
vous vous en éloignez. Quand vous n’utilisez pas l’appareil,
éteignez-le et libérez la pression conformément aux instructions
Comment libérer la pression, du présent manuel.
• Vérifiez que toutes les connexions sont bien serrées avant
d’utiliser l’appareil. Toute pièce qui n’est pas fixée solidement
risque d’être projetée violemment ou d’entraîner la fuite d’un jet
de liquide à une pression extrêmement élevée, ce qui pourrait
causer des blessures graves.
• Verrouillez toujours la détente quand vous ne pulvérisez pas.
Vérifiez que le verrou de la détente fonctionne correctement.
DANGER : EXPLOSION OU INCENDIE
Les émanations de certains produits peuvent exploser
ou s’enflammer, et risquent d’entraîner des dommages
matériels ou de graves blessures.
MESURES PRÉVENTIVES :
• S’assurer que l’aire de travail est dotée de moyens d’évacuation
d’air vicié et d’introduction d’air frais pour éviter l’accumulation de
vapeurs inflammables. Les vapeurs dégagées par la peinture ou
les solvants peuvent provoquer une explosion ou s’enflammer.
• Ne pas pulvériser de produit dans un endroit clos.
• Ne pas travailler près de sources d’ignition (décharges
électrostatiques ou étincelles provoquées par le branchement/
débranchement d’appareils ou la commutation d’interrupteurs,
d’appareils électriques, flammes nues, veilleuses,
objets chauds, etc.). La peinture ou le solvant
s’écoulant dans l’équipement peut générer de
l’électricité statique.
• Ne pas fumer dans l’aire de travail.
• L’aire de travail doit être munie d’un extincteur en bon
état de marche.
• Prévoir un espace d’au moins 7.62 mètres entre la pompe et l’objet
à pulvériser s’ils sont dans la même pièce bien ventilée (rallonger le
flexible au besoin). Les vapeurs inflammables étant souvent plus lourdes
que l’air, l’espace au-dessus du plancher doit être particulièrement bien
aéré. La pompe contient des pièces qui produisent des arcs et émettent
des étincelles pouvant enflammer les vapeurs.
• Les appareils et objets à l’intérieur ou à proximité de l’aire de
travail doivent être adéquatement mis à la terre pour éviter les
décharges électrostatiques.
• Veillez à ce que la zone soit propre et exempte de contenants de
peinture ou de solvant, chiffons ou autres matériaux inflammables.
• Les flexibles dont on se sert doivent être conçus pour subir les
pressions élevées et faits de matériaux conducteurs ou mis à la
terre adéquatement; le pistolet sera mis à la terre par le biais de
ses raccords aux flexibles.
• Pour les appareils électriques — Le cordon d’alimentation doit
être branché à un circuit trifilaire.
• L’appareil doit toujours être vidangé à basse pression, embout
retiré, dans un contenant métallique distinct. Tenir le pistolet
contre la paroi du contenant de manière à mettre ce dernier à la
terre et à prévenir les décharges électrostatiques.
• Toujours respecter les mises en garde et les directives du
fabricant des produits et solvants utilisés. On doit connaître les
produits contenus dans les peintures et solvants qu’on pulvérise.
Lire les fiches techniques santé-sécurité (FTSS) et les étiquettes
des contenants fournies avec les peintures et solvants. Suivres
les consignes de sécurité du fabricant de peinture et de solvant.
• S’entourer de toutes les précautions possibles lorsqu’on utilise
des produits ayant un point d’éclair inférieur à 21°C (70°F). Le
point d’éclair est la température à laquelle le liquide peut créer
suffisamment de vapeurs et s’enflammer.
• Le plastique est générateur de décharges électrostatiques; ne jamais
en suspendre pour fermer une aire de travail ou en utiliser en guise
de toile de protection lorsqu’on pulvérise un produit inflammable.
• Se servir de la pression la plus basse possible pour vidanger
l’appareil.
• Ne pas pulvériser de produit sur la pompe.
remarque à l’intention des MÉDECINS :
Les injections cutanées sont des lésions traumatiques; il
importe donc de les traiter sans délai. On NE DOIT PAS retarder
ce traitement sous prétexte de vérifier la toxicité du produit en
cause, celle-ci n’étant conséquente que dans le cas d’injection
directe de certains produits dans le système sanguin. Il pourrait
s’avérer nécessaire de consulter un plasticien ou un spécialiste
en chirurgie reconstructive de la main.
Français
16
© Titan Tool Inc. Tous droits réservés.
Consignes de sécurite important ·
Lire toutes ces consignes avant
d’utiliser l’appareil. Garder ces consignes.
Instructions de mise à la terre
DANGER : EXPLOSION CAUSÉE PAR DES
PRODUITS INCOMPATIBLES
Ce type d’explosion peut entraîner des dommages
matériels ou des blessures graves.
MESURES PRÉVENTIVES :
• Ne pas utiliser de produits contenant du chlore ou du javellisant.
• Ne pas utiliser de solvants à base de halons comme l’eau de
javel, les agents antimoisissure, le chlorure de méthylène et le
trichloroéthane-1-1-1, lesquels ne sont pas compatibles avec
l’aluminium.
• Communiquer avec le fournisseur du produit concerné pour en
connaître la compatibilité avec l’aluminium.
Cet appareil doit être mis à la terre. La mise à la terre réduit les risques
d’électrocution lors d’un court-circuit en permettant au courant de
s’écouler par le fil de mise à la terre. Cet appareil est muni d’un cordon
électrique avec fil de mise à la terre ainsi que d’une fiche de terre. La
fiche doit être branchée sur une prise installée correctement et mise à la
terre conformément à la réglementation et aux codes en vigueur.
MISE EN GARDE - Le fait de ne pas brancher
correctement la fiche trifilaire de l’appareil peut entraîner
des risques de choc électrique.
DANGER : GÉNÉRALITÉS
D’autres dangers peuvent entraîner des dommages matériels ou des
blessures graves.
MESURES PRÉVENTIVES :
• Lire toutes les directives et consignes de sécurité avant d’utiliser
l’appareil.
• Observer tous les codes locaux, provinciaux, d’état et nationaux
régissant la ventilation, la prévention des incendies et le
fonctionnement de l’appareil.
• Aux États-Unis, le gouvernement a adopté des normes de
sécurité en vertu de l’Occupational Safety and Health Act
(OSHA). Le cas échéant, on doit les consulter, notamment les
parties 1910 des normes générales et 1926 des normes de
construction.
• N’utiliser que les pièces autorisées par le fabricant; les
utilisateurs qui choisiront d’utiliser des composants dont les
caractéristiques techniques et les exigences en matière de
sécurité sont inférieures devront en assumer tous les risques et
responsabilités.
• Tous les raccords, les tuyaux et les bouchons de remplissage
doivent être fixés solidement en place avant d’utiliser la pompe
de pulvérisation. Toute pièce qui n’est pas fixée solidement
risque d’être projetée violemment ou d’entraîner la fuite d’un jet
de liquide à une pression extrêmement élevée, ce qui pourrait
causer des blessures graves.
• Avant chaque utilisation, examiner tous les flexibles afin de
confirmer l’absence de coupures, de fuites, d’abrasions ou
de renflements. Vérifier également l’intégrité des raccords.
Remplacer sans délai les pièces qui semblent présenter des
défectuosités. Ne jamais tenter de réparer un flexible; remplacer
ceux qui font défaut par des modèles haute pression, avec mise à
la terre.
•. Ne faites pas de nouer avec le tuyau et ne le tordez pas trop. Le
tuyau à vide peut présenter des fuites suite à l’usure, les nouer
ou les mauvais traitements. Une fuite risque d’injecter du produit
dans la peau.
•. N’exposez pas le tuyau à des températures ou des pressions
supérieures à celles spécifiées par le fabricant.
• Ne pas pulvériser à l’extérieur par grands vents.
• Porter des vêtements aptes à protéger la peau et les cheveux du
produit utilisé.
• Ne pas utiliser le pistolet ou ne pas pulvériser de produits
en présence d’enfants à proximité. Éloigner les enfants de
l’équipement en tout temps.
• Ne pas s’étirer ni ne travailler sur un support instable. Toujours
garder les deux pieds au sol pour rester en équilibre.
• Se servir de la pression la plus basse possible pour vidanger
l’appareil.
• Rester vigilant et faire attention à ce que l’on fait.
• Ne pas se servir de l’équipement en cas de fatigue ou si vos
aptitudes sont affaiblies par la consommation de drogues ou de
boissons alcoolisées.
• Pour les appareils électriques — Débranchez toujours le cordon
électrique de la prise avant de travailler sur l’équipement.
• N’utilisez pas le tuyau pour tirer ou soulever l’équipement.
• Ne pas soulever par la poignée de chariot en chargeant ou en
déchargeant.
© Titan Tool Inc. Tous droits réservés.
Si on doit réparer ou remplacer le cordon ou la fiche, ne pas raccorder
le fil de terre à la borne des broches plates (lames) de cette dernière. Ce
fil, normalement vert (avec ou sans rayures jaunes), doit être relié à la
broche de terre.
Consulter un technicien ou un électricien qualifié à défaut de comprendre
l’ensemble des présentes directives ou en cas d’incertitude quant à la
mise à terre de l’appareil. Ne pas modifier la fiche de l’appareil; si elle ne
s’adapte pas dans la prise voulue, faire remplacer cette dernière par un
électricien qualifié.
Prise trifilaire
Broche de mise à la terre
Plaque murale de la prise
Important : Utiliser uniquement une rallonge à trois fils
munie d’une fiche de terre dans une prise secteur mise à la terre
correspondant au type de fiche de l’appareil. S’assurer que votre
rallonge est en bon état. Lorsque vous utilisez une rallonge,
assurez-vous qu’elle soit d’un calibre suffisant pour supporter
l’intensité du courant requise par l’appareil. Une rallonge trop
mince entraîne une chute de tension, une diminution de l’intensité
et une surchauffe. Une rallonge de calibre 12 est recommandée.
Si vous devez utiliser une rallonge à l’extérieur, celle-ci doit
comprendre la marque W-A après la désignation indiquant le type de
cordon. Par exemple, la désignation SJTW-A indique que le cordon
est conçu pour être utilisé à l’extérieur.
17
Français
Información de seguridad importante ·
Lea toda la información de
seguridad antes de operar el equipo. Guarde estas instrucciones.
PELIGRO: VAPORES PELIGROSOS
Las pinturas, solventes, insecticidas y demás materiales
pueden ser nocivos si se inhalan o toman contacto con
el cuerpo. Los vapores pueden causar náuseas graves,
desmayos o envenamiento.
Indica una situación peligrosa que, de no evitarse, puede
causar la muerte o lesiones graves.
Para reducir los riesgos de incendios, explosiones,
descargas eléctricas o lesiones a las personas, lea y
entienda todas las instrucciones incluidas en este
manual. Familiarícese con los controles y el uso
adecuado del equipo.
PREVENCIÓN:
PELIGRO: LESIÓN POR INYECCIÓN
El flujo de pintura a alta presión que produce este
equipo puede perforar la piel y los tejidos subyacentes,
ocasionando lesiones graves y posible amputación.
CONSULTE A UN MÉDICO INMEDIATAMENTE.
¡NO TRATE LA LESIÓN POR INYECCIÓN COMO UNA
CORTADURA SIMPLE! La inyección puede ocasionar amputación.
Consulte a un médico inmediatamente.
La gama operativa máxima de la pistola es de 3300 PSI / 22.8 MPa de
presión del líquido.
PREVENCIÓN:
• NUNCA apunte la pistola a ninguna parte del cuerpo.
• No apunte con la pistola ni rocíe a cualquier persona o animal.
• NUNCA deje que ninguna parte del cuerpo toque el flujo de
líquido. NO deje que el cuerpo toque una fuga de la manguera de
líquido.
• NUNCA ponga la mano frente a la pistola. Los guantes no
protegen contra una lesión por inyección.
• SIEMPRE ponga el seguro del gatillo, apague la bomba y
libere toda la presión antes de dar servicio, limpiar la boquilla o
protección, cambiar la boquilla o dejar la pistola sin supervisión.
No se libera la presión al apagar el motor. Debe girarse la perilla
PRIME/ SPRAY (CEBAR/ROCIAR) a PRIME (CEBAR) para
aliviar la presión. Consulte el PROCEDIMIENTO PARA ALIVIAR
LA PRESIÓN descrito en este manual.
• SIEMPRE mantenga la protección de la boquilla en su sitio
al rociar. La protección de la boquilla sirve principalmente de
dispositivo de advertencia.
• SIEMPRE retire la boquilla rociadora antes de enjuagar o limpiar
el sistema.
• La manguera de pintura puede presentar fugas por desgaste,
dobleces y maltrato. La fuga puede inyectar material traspasando
la piel. Inspeccione la manguera antes de cada uso. No use
mangueras para levantar o tirar del equipo.
• NUNCA use una pistola rociadora sin contar con el seguro y la
protección del gatillo.
• Todos los accesorios deben tener capacidades nominales de
3300 PSI / 22.8 MPa como mínimo. Esto incluye las boquillas
rociadoras, pistolas, extensiones y manguera.
• No deje el aparato con corriente ni con presión cuando nadie esté
pendiente de ella. Cuando no utilice el aparato, apáguelo y libere
la presión siguiendo las instrucciones del PROCEDIMIENTO
PARA ALIVIAR LA PRESIÓN descrito en este manual.
• Antes de utilizar el aparato, verifique que todas las conexiones
son seguras. Las partes no aseguradas pueden ser expulsadas
con gran fuerza o filtrar fluido a alta presión y provocar lesiones
severas.
• Ponga siempre el seguro del gatillo cuando no esté pulverizando.
Verifique que el seguro del gatillo funciona correctamente.
PELIGRO: EXPLOSIÓN O INCENDIO
Los vapores de solventes y pinturas pueden explotar o
inflamarse. Pueden producirse daños materiales, lesiones
graves o ambos.
PREVENCIÓN:
NOTA PARA EL MÉDICO:
La inyección a través de la piel es una lesión traumática. Es
importante tratar la lesión tan pronto sea posible. NO retrase
el tratamiento para investigar la toxicidad. La toxicidad es
un factor a considerar con ciertos revestimientos inyectados
directamente en la corriente sanguínea. Puede ser aconsejable
consultar con un cirujano plástico o un cirujano especialista en
reconstrucción de las manos.
Español
• Use un respirador o mascarilla si pueden
inhalarse los vapores. Lea todas las instrucciones
suministradas con la mascarilla para revisar que
brinde la protección necesaria.
• Use lentes protectores.
• Use ropa protectora según lo indique el fabricante del
revestimiento.
18
• Cuente con escape y entrada de aire fresco para mantener el aire
dentro de la zona de aplicación sin acumulaciones de vapores
inflamables. Los gases producidos por solventes o pinturas
pueden causar explosiones o incendios.
• No rocíe en lugares cerrados.
• Evite todas las fuentes de ignición como las chispas de
electricidad estática, las llamas expuestas,
appliances electricidad, las luces piloto y los
objetos calientes. La conexión o desconexión de
cables eléctricos o interruptores de luz operativos
puede producir chispas. Si la pintura o el solvente
fluyen por el equipo se puede generar electricidad
estática.
• No fume en el área de aplicación.
• Debe haber un extintor de incendios en buen estado.
• Coloque la bomba de pintura a un mínimo de 7.62 meters (25
pies) del objeto a pintar dentro de un área bien ventilada (añada
más manguera si es necesario). Los vapores inflamables son
generalmente más pesados que el aire. El área debe estar
sumamente bien ventilada.
• El equipo y los objetos dentro y alrededor del área a pintar deben
estar debidamente conectados a tierra para evitar las chispas de
estática.
• Mantenga el área limpia y libre de contenedores de pintura o
solvente, trapos y otros materiales inflamables.
• Use solamente una manguera conductora o conectada a tierra
para líquidos a alta presión. La pistola debe conectarse a tierra a
través de las conexiones de la manguera.
• Para las aparatos eléctricas — Debe conectarse el cable eléctrico
a un circuito a tierra.
• Siempre enjuague la unidad dentro de un recipiente metálico
separado, con la bomba a baja presión y habiendo sacado la
boquilla rociadora. Sostenga la pistola firmemente contra el
costado del recipiente para conectar a tierra el mismo y evitar
chispas de estática.
• Siga las advertencias e instrucciones del fabricante del material
y del solvente. Conozca los contenidos de las pinturas y los
solventes con los que rocía. Lea todas las Hojas de Datos sobre
Seguridad de Materiales (MSDS) y las etiquetas del contenedor
provistas con las pinturas y los solventes. Siga las instrucciones
de seguridad del fabricante de pinturas o solventes.
• Tenga muchísmo cuidado al usar materiales cuyo punto de
ignición sea inferior a 70°F (21°C). El punto de inflamación es la
temperatura a la que un fluido puede producir vapores suficientes
para encenderse.
• El plástico puede causar chispas de estática. Nunca cuelgue
plásticos para cerrar una zona a pintar. No use mantas plásticas
al aplicar materiales inflamables.
• Use la presión más baja posible para enjuagar el equipo.
• No rocíe el ensamblaje de la bomba.
© Titan Tool Inc. Todos los derechos reservados.
Información de seguridad importante ·
Lea toda la información de
seguridad antes de operar el equipo. Guarde estas instrucciones.
Instrucciones para conectar a tierra
PELIGRO: POSIBLE EXPLOSIÓN DEBIDO A
MATERIALES INCOMPATIBLES
Causará daños materiales o lesiones graves.
Este producto se debe conectar a tierra. En caso de que ocurra un
corto circuito, la conexión a tierra reduce el riesgo de choque eléctrico
al proporcionar un alambre de escape para la corriente eléctrica. Este
producto está equipado con un cable que tiene un alambre de conexión a
tierra con un enchufe de conexión a tierra apropiado. El enchufe se debe
enchufar en una toma de corriente que se haya instalado y conectado a
tierra debidamente, de acuerdo con todos los códigos y estatutos locales.
PREVENCIÓN:
• No use materiales que contengan blanqueador o
cloro.
• No use solventes de hidrocarburos halogenados como
blanqueador, mohocida, cloruro de metileno y 1,1,1 tricloroetano.
No son compatibles con el aluminio.
• Diríjase al proveedor de revestimientos para obtener los datos de
compatibilidad del material con el aluminio.
ADVERTENCIA - La instalación incorrecta del enchufe a
tierra puede ocasionar un riesgo de choque eléctrico.
PELIGRO: GENERAL
Puede causar daños materiales o lesiones graves.
PREVENCIÓN:
• Lea todas las instrucciones y las precauciones de seguridad
antes de operar el equipo.
• Siga todos los códigos locales, estatales y nacionales
correspondientes que rijan la ventilación, prevención de incendios
y operación.
• Se han adoptado las normas de seguridad del Gobierno de los
Estados Unidos según la Ley de seguridad ocupacional y salud
(Occupational Safety and Health Act, OSHA). Deben consultarse
estas normas, particularmente el apartado 1910 de las Normas
generales y el apartado 1926 de las Normas de construcción.
• Utilice solamente componentes autorizados por el fabricante.
El usuario asume todo riesgo y responsabilidad al utilizar
componentes que no cumplan con las especificaciones mínimas
y requisitos de seguridad del fabricante de la bomba.
• Todos los acopladores, las mangueras y las tapas de los filtros
deben estar asegurados antes de operar la bomba de rocío. Las
partes no aseguradas pueden ser expulsadas con gran fuerza o
filtrar fluido a alta presión y provocar lesiones severas.
• Antes de cada uso, revise todas las mangueras en busca de
cortes, fugas, abrasión o hinchazón de la cubierta. Revise
si hay daños o movimiento de los acoplamiento. Cambie
inmediatamente la manguera si existe alguna de estas
condiciones. Nunca repare una manguera de pintura. Cámbiela
por otra manguera conectada a tierra apta para alta presión.
• No retuerza ni doble la manguera en exceso. En la manguera
airless pueden aparecer fugas a causa del desgaste, de
retorcimientos o de un mal uso. Una fuga puede inyectar material
en la piel.
• No exponga la manguera a temperaturas o presiones que
superen las especificadas por el fabricante.
• No pinte en exteriores en días con viento.
• Use ropa que mantenga la pintura alejada de la piel y el cabello.
• No lo opere ni rocíe cerca de los niños. Mantenga a los niños
alejados del equipo en todo momento.
• No se asome ni se pare sobre soportes inestables. Mantenga
siempre la posición firme y el equilibrio efectivos.
• Use la presión más baja posible para enjuagar el equipo.
• Manténgase alerta y mire lo que hace.
• No utilice la unidad cuando se encuentre cansado o bajo la
influencia de las drogas o el alcohol.
• Para las aparatos eléctricas — Desenchufe siempre el cable
antes de trabajar en el equipo.
• No utilice la manguera como elemento de fuerza para tirar del
equipo o levantarlo.
• No levantar por la manija del carro al cargar o descargando.
© Titan Tool Inc. Todos los derechos reservados.
Si es necesario reparar o cambiar el cable o el enchufe, no conecte el
cable verde a tierra a ninguno de las terminales de espiga plana. El cable
con aislamiento de color verde por fuera con o sin rayas amarillas es el
alambre a tierra y debe conectarse a la espiga a tierra.
Consulte a un electricista o técnico de servicio capacitado si las
instrucciones para la conexión a tierra no se entienden claramente o si
tiene dudas en cuanto a que el producto esté debidamente conectado a
tierra. No modifique el enchufe que se incluye. Si el enchufe no encaja
en el receptáculo, pida a un electricistas capacitado que instale un
receptáculo adecuado.
Receptáculo conectado a tierra
Pata a tierra
Tapa de la caja de receptáculo conectada a tierra
ImportantE: Use solamente extensiones trifilares que tengan un
enchufe de conexión a tierra de 3 hojas y un receptáculo de triple
ranura que acepte el enchufe del producto. Asegúrese de que su
extensión esté en buenas condiciones. Cuando use una extensión,
asegúrese de usar una que sea lo suficientemente resistente como
para soportar la corriente que descargue su producto. Un cable de
un tamaño menor causará una caída de voltage en la línea que dará
como resultado una pérdida de energía y un sobrecalenta|ôento. Se
recomienda usar un cable de calibre 12. Si se utiliza un cable de
extensión en el exterior, tiene que estar marcado con el sufijo W-A
después de la designación del tipo de cable. Por ejemplo, SJTW-A
para indicar que el cable es apropiado para uso en exteriores.
19
Español
Parts List
Main Assembly
1
2
3
4
5
6
7
16
17
18
8
19
9
20
10
11
12
13
14
21
22
15
Item
1
2
3
4
5
6
7
8
9
10
11
12
Part #
800-600
800-477
800-478
800-479
----------
800-480
761-178
800-324
763-551
858-625
800-328
800-268
DescriptionQuantity
High rider cart............................................1
Bolt............................................................2
Flat washer................................................2
Tool box.....................................................1
Drive assembly (see separate listing).......1
Hex nut......................................................2
Screw.........................................................4
Pail hook....................................................1
Lock washer..............................................2
Screw.........................................................2
Knock-off nut.............................................1
Fitting . ......................................................1
Item
13
14
15
16
17
18
19
20
21
22
23
24
20
Part #
800-710
730-334
800-904
800-481
812-003
800-915
800-269
800-482
860-002
860-535
800-266
818-002
DescriptionQuantity
Fluid section assembly..............................1
Hose clamp................................................1
Return hose...............................................1
Filter plug assembly...................................1
Outlet fitting...............................................1
PRIME/SPRAY valve assembly................1
Fitting.........................................................1
Fitting.........................................................1
Lock washer..............................................2
Screw.........................................................2
Hose (not shown)......................................1
Elbow (not shown).....................................2
© Titan Tool Inc. All rights reserved.
Drive Assembly
1
2
3
4
29
5
30
6
31
7
32
33
8
34
9
17
18
19
20
21
10
11
12
35
22
13
23
14
24
36
25
26
27
28
15
37
16
Item Part #
1
800-078
2
800-205
3
800-984
4
800-525
5
800-541
6
800-261
7
800-262
8
800-260
9
704-380
10
800-510
11
800-253
12
700-283
13
800-483
14
800-284
15
800-382
16
800-753
17
800-229
18
779-568
19
800-077
20
800-076
21
800-688
22
704-486
23
704-488
24
704-473
38
DescriptionQuantity
Electronic cover.........................................1
Screw.........................................................3
Motor assembly.........................................1
Housing gasket..........................................1
Shroud gasket...........................................1
1st stage gear assembly...........................1
2nd stage gear asembly............................1
Front gearbox assembly............................1
ON/OFF switch..........................................1
Slider assembly.........................................1
Slider housing............................................1
Screw.........................................................4
Front cover................................................1
Screw.........................................................4
Retaining ring............................................1
Connecting pin..........................................1
Ground screw............................................1
Mounting plate...........................................1
Grommet....................................................1
Screw.........................................................1
Control panel.............................................1
Screw.........................................................4
Pressure control knob...............................1
Control panel cover (for sprayers without
Xact Digital Control System)......................1
© Titan Tool Inc. All rights reserved.
Item Part #
25
704-599
26
704-487
27
779-567
28
704-553
29
700-287
30
763-551
31
800-658
32
800-215
33
800-294
34
800-435
35
800-283
36
800-484
37
704-469
38
704-467
39
704-594
40
800-929
41
770-781
42
765-060
43
770-596
700-742
DescriptionQuantity
Dust cover (for sprayers without Xact
Digital Control System)..............................1
Screw.........................................................2
Strain relief................................................1
Power cord................................................1
Screw.........................................................3
Lock washer..............................................3
Electronic control assembly.......................1
Fan shroud................................................1
Fan assembly............................................1
Baffle assembly.........................................1
Screw.........................................................4
Motor shroud.............................................1
Xact Digital Control System assembly
(optional)....................................................1
Xact Digital Control system cover ..............
(optional)....................................................1
Surge suppressor (not shown)..................1
Fuse, 15A (not shown)..............................1
Electronic control mounting screw
(not shown)................................................4
Electronic control lock washer (not shown)... 4
Electronic control washer (not shown)......4
Tie wrap (not shown)
NOTE:All electrical work should be performed by a Titan
authorized service center.
21
Fluid Section Assembly (P/N 800-710)
1
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
11
12
13
2
3
14
15
16
4
17
18
5
6
7
8
9
10
30
19
20
21
22
Part #
800-634
800-643
800-636
800-638
800-637
800-639
800-325
800-327
800-353
800-351
800-355
800-354
800-332
800-333
800-352
800-246
800-348
800-244
704-702
800-245
800-243
800-336
800-322
288-011
800-241
762-058
800-635
451-018
431-054
800-720
800-730
800-359
23
DescriptionQuantity
Cylinder.....................................................1
Stopping spacer........................................1
Extension bushing.....................................1
Piston extension........................................1
Extension slider.........................................1
Connecting pin..........................................2
Upper seal retainer....................................1
Spacer.......................................................1
Upper packing assembly...........................1
Upper housing...........................................1
Lower packing assembly...........................1
Wear ring...................................................1
O-ring, Viton..............................................2
Back-up ring, Teflon..................................2
Lower housing...........................................1
Piston rod..................................................1
Outlet valve seal........................................1
Outlet valve cage.......................................1
Outlet valve ball.........................................1
Washer, nylon............................................1
Outlet valve seat........................................1
Outlet valve retainer..................................1
Foot valve cage.........................................1
Foot valve ball...........................................1
Foot valve seat..........................................1
O-ring.........................................................1
Foot valve housing....................................1
Inlet screen................................................1
Retaining ring............................................1
Piston assembly (includes items 16–22)...1
Repacking kit (includes items 8, 9, 11–14,
17, 19, 20, 24, and 26)
Lower packing insertion tool
NOTE: When repacking the fluid section, make sure the
raised lip on the bottom of the lower packing is
fully outside the packing around the piston rod
after insertion of the piston rod.
24
25
26
13
14
27
28
29
22
© Titan Tool Inc. All rights reserved.
High Rider Cart (P/N 800-600)
Filter Plug Assembly (P/N 800-481)
1
1
2
2
3
3
4
4
5
5
7
6
Item
1
2
3
4
5
6
7
10
11
6
7
12
8
13
9
14
DescriptionQuantity
Filter plug...................................................1
O-ring, Teflon.............................................1
Plug, 3/8”...................................................1
Filter housing.............................................1
PRIME/SPRAY valve assembly................1
Plug, 1/4”...................................................1
Transducer................................................1
NOTE: The flter plug assembly comes installed on the
sprayer and is used when spraying textured
products from a ready-mixed or powdered
formulation.
15
Item Part #
1
800-280
2
590-508
3
590-507
4
590-504
5
590-506
6
800-011
7
710-199
8
800-279
9
335-018
10
856-002
11
856-921
12
800-007
13
670-109
14
870-004
15
800-019
Part #
800-612
800-906
800-908
800-901
800-915
800-907
800-437
DescriptionQuantity
Handle
(includes items 2–5, 10, and 11)...............1
Roll pin.......................................................2
Snap button...............................................2
Sleeve........................................................2
Washer......................................................2
Spacer.......................................................2
Plug...........................................................2
Cart (includes items 7 and 9)....................1
Plug...........................................................2
Washer......................................................4
Screw.........................................................4
Axle............................................................1
Wheel........................................................2
Washer......................................................2
Cap............................................................2
PRIME/SPRAY Valve Assembly (P/N 800-915)
2
1
3
4
5
6
7
8
Item
1
2
3
4
5
6
7
8
Part #
800-915
700-537
222-012
221-012
700-721
700-897
700-252
700-759
700-697
DescriptionQuantity
PRIME/SPRAY valve assembly................1
Gasket.......................................................1
O-ring, Teflon.............................................1
O-ring, Viton..............................................1
Valve stem o-ring, Viton............................1
Valve stem o-ring, Teflon (optional)
Cam base..................................................1
Groove pin.................................................1
Valve handle..............................................1
NOTE: When using “hot” solvents, replace Viton valve
stem o-ring (item 5) with optional Teflon valve
stem o-ring (P/N 700-897). Install using o-ring
replacement tool (P/N 700-890).
© Titan Tool Inc. All rights reserved.
23
Filter Parts
Labels
NOTE: The following parts are included with the unit
and can be installed into the filter housing when
spraying standard materials.
1
Part #
0524939
0524938
313-1673
313-1847
313-2395
313-2324
313-2327
313-2328
313-2430
Description
Logo label
Front label
Warning label (injection/explosion)
Shock hazard label
Infinity logo label
X-Lock label
Xact Digital Control System label
Xact Instruction label
Transducer warning label
2
3
4
5
Item
1
2
3
4
5
Part #
800-705
800-252
730-067
702-251
757-105
DescriptionQuantity
Filter body..................................................1
Filter spring................................................1
Filter, 60 mesh...........................................1
Filter spring adapter..................................1
Core spring................................................1
24
© Titan Tool Inc. All rights reserved.
Electrical Schematic
Transducer
WHITE
Plug
Potentiometer
GREEN
Fuse, 15A
J1
Switch
J16
J2
BLACK
Ground
WHITE
AC-Motor
BLACK
Surge
Suppressor
AC-Line
J9
J12
J7
Motor
AC-Motor
AC-Neut
Control Panel
Board
WHITE
Electronic Control
Assembly
WHITE
NOTE:All electrical work should be performed by an
authorized service center.
© Titan Tool Inc. All rights reserved.
25
Accessories
Synergy Fine Finish Tips
Tips are selected by the orifice size and fan width. The proper
selection is determined by the fan width required for a specific job
and by the orifice size that will supply the desired amount of fluid
and accomplish proper atomization.
For light viscosity fluids, smaller orifice tips generally are desired.
For heavier viscosity materials, larger orifice tips are preferred.
Please refer to the chart below.
Airless Tip Selection
NOTE: Do not exceed the sprayer’s recommended tip
size.
WideSpray Reversible Tips
The following chart indicates the most common sizes and the
appropriate materials to be sprayed.
Tip Size
Spray Material
Filter Type
.011 – .013
Lacquers and stains
100 mesh filter
.015 – .019
Oil and latex
60 mesh filter
.021 – .026
Heavy bodied latex and blockfillers
30 mesh filter
• Operates your sprayer from over 100 feet away
• Works through walls, trees and other obstacles
• Increase or decrease the pressure of the sprayer without
climbing down off the ladder
Part #
Description
800-690.......I-Remote Control System
800-691.......I-Remote Control Only
800-692.......I-Remote Receiver Only
Liquid Shield Plus
Cleans and protects spray systems against
rust, corrosion and premature wear. Now with
-25º anti-freeze protection.
Part #
Description
314-483.......4 ounce bottle
314-482.......1 quart bottle
Xact Digital Control System
The Xact Digital Control System is an optional add-on that
increases the functionality of the sprayer. It consists of a display
and four function keys. The display shows the user menu
features that enable the user to become more productive and
profitable
• X-Lock Security Features (Individualized Codes)
• Pressure Reading — Set Pressure and Working Pressure
• User Preset Keys
• Total Gallons Sprayed
• Resetable Job Gallon Counter
• Total On Time and Run Time
• Resetable On Time and Run Time
• Programmable Service Time (Hour Meter)
• Advanced Diagnostics
Part #
Description
704-555.......Xact Digital Control System with Cover
Piston Lube
Specially formulated to prevent materials from
adhering to the piston rod, which becomes
abrasive to the upper seals. Piston Lube will
break down any material that may accumulate
in the oil cup and keep it from drying.
Part #
Description
314-481.......4 ounce bottle
314-480.......8 ounce bottle
LX-80II Airless Gun
3600 PSI
All metal construction
In-handle filter
High pressure swivel
Part #
Description
580-100.......LX-80II — 4 Finger Gun
581-085.......LX-80II — 2 Finger Gun
580-050.......LX-80II — 4 Finger GTH Kit
581-150.......LX-80II — 2 Finger GTH Kit
Miscellaneous
S-3 Stainless Steel Airless Gun
•
•
•
•
•
• Designed for high production applications
• Increase production up to 100%
• WideSpray will save time and make you more money
Part No.
Description
661-XXXX
WideSpray Reversible Tips
I-Remote Universal Remote Control System
Fan widths measuring 8” to 12” (20 to 30 cm) are preferred
because they offer more control while spraying and are less likely
to plug.
•
•
•
•
• Perfect for all fine finish work
• Ideal for lacquers, stain, enamels, urethane, and clear top
coats
• Increases standard tip life up to 80%
• Delivers up to a 27% finer atomization at lower pressures
• Increases transfer efficiency resulting in less overspray
Part #
Description
671-XXX
Synergy Fine Finish Tips
3900 PSI
Stainless Steel fluid passages
High Pressure Swivel
In-handle filter
4-finger trigger pull
Part #
Description
550-250
S-3 — 4 Finger Gun
26
Part #
Description
490-012.......Hose Coupling, 1/4” x 1/4”
730-397.......High Pressure Fl. Gauge
314-171.......Lubriplate, 14 ounce individual
314-172.......Lubriplate, 6 lb. can
700-1037.....Electrostatic discharge (ESD) wrist strap
© Titan Tool Inc. All rights reserved.
Patents
These products are covered by one or more of the following U.S. patents:
6,031,352
5,848,566
5,769,321
5,725,364
5,346,037
5,252,210
5,217,238
5,192,425
D384,676
6,179,222
5,934,883
4,723,892
5,671,656
4,908,538
5,435,697
4,768,929
5,228,842
4,744,571
Material Safety Data Sheets (MSDS) are available on Titan’s website or by calling Customer Service.
Brevets
Ces produits sont protégés par un ou plusieurs des brevets (U.S.A.) suivants :
6,031,352
5,848,566
5,769,321
5,725,364
5,346,037
5,252,210
5,217,238
5,192,425
D384,676
6,179,222
5,934,883
4,723,892
5,671,656
4,908,538
5,435,697
4,768,929
5,228,842
4,744,571
Des fiches techniques de sécurité des produits (FTSS) sont disponibles sur le site Internet de Speeflo’s ou par téléphone
en vous adressant au Service Client.
Patentes
Estos productos están protegidos por una de las siguientes patentes (U.S.A.):
6,031,352
5,848,566
5,769,321
5,725,364
5,346,037
5,252,210
5,217,238
5,192,425
D384,676
6,179,222
5,934,883
4,723,892
5,671,656
4,908,538
5,435,697
4,768,929
5,228,842
4,744,571
Las Hojas de Datos de Seguridad (Material Safety Data Sheets - MSDS) se encuentran disponibles en el sitio web de
Speeflo’s o llamando al Servicio al Cliente.
© Titan Tool Inc. All rights reserved.
27
Warranty • Garantie • Garantía
Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from
defects in material and workmanship. With the exception of any special, limited, or extended warranty published by Titan, Titan’s obligation under this warranty
is limited to replacing or repairing without charge those parts which, to Titan’s reasonable satisfaction, are shown to be defective within twelve (12) months after
sale to the End User. This warranty applies only when the unit is installed and operated in accordance with the recommendations and instructions of Titan.
This warranty does not apply in the case of damage or wear caused by abrasion, corrosion or misuse, negligence, accident, faulty installation, substitution of
non-Titan component parts, or tampering with the unit in a manner to impair normal operation.
Defective parts are to be returned to an authorized Titan sales/service outlet. All transportation charges, including return to the factory, if necessary, are to be
borne and prepaid by the End User. Repaired or replaced equipment will be returned to the End User transportation prepaid.
THERE IS NO OTHER EXPRESS WARRANTY. TITAN HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED
TO, THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TO THE EXTENT PERMITTED BY LAW. THE DURATION OF ANY
IMPLIED WARRANTIES WHICH CANNOT BE DISCLAIMED IS LIMITED TO THE TIME PERIOD SPECIFIED IN THE EXPRESS WARRANTY. IN NO CASE
SHALL TITAN LIABILITY EXCEED THE AMOUNT OF THE PURCHASE PRICE. LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES
UNDER ANY AND ALL WARRANTIES IS EXCLUDED TO THE EXTENT PERMITTED BY LAW.
TITAN MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
WITH RESPECT TO ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY TITAN. THOSE ITEMS SOLD,
BUT NOT MANUFACTURED BY TITAN (SUCH AS GAS ENGINES, SWITCHES, HOSES, ETC.) ARE SUBJECT TO THE WARRANTY, IF ANY, OF THEIR
MANUFACTURER. TITAN WILL PROVIDE THE PURCHASER WITH REASONABLE ASSISTANCE IN MAKING ANY CLAIM FOR BREACH OF THESE
WARRANTIES.
Titan Tools, inc. (« Titan ») garantit qu’au moment de la livraison à l’acheteur original (« Utilisateur »), l’appareil couvert par la présente garantie sera exempt
de défauts de matériaux et de fabrication. Avec l’exception de spécial, limité, ou garantie allongée publiée par de Titan, les responsabilités de Titan en vertu de
cette garantie se limitent au remplacement ou à la réparation sans frais des pièces dont on aura, à la satisfaction raisonnable de Titan, démontré la défectuosité
dans un délai de douze (12) mois après la date d’achat par l’Utilisateur. Cette garantie ne s’applique que si l’appareil a été installé et utilisé conformément aux
recommandations et directives de Titan.
Cette garantie ne s’applique pas dans les cas d’endommagement ou d’usure engendrés par de l’abrasion, de la corrosion, un mauvais usage, de la négligence,
un accident, une installation incorrecte, un remplacement par des composants non fournis par Titan ou toute intervention non autorisée apte à nuire au
fonctionnement normal de l’appareil.
Les pièces défectueuses doivent être envoyées à un centre de service/vente Titan autorisé; les frais de transport, incluant le retour à l’usine, le cas échéant,
doivent être défrayés à l’avance par l’Utilisateur. Une fois remplacées ou réparées, les pièces seront renvoyées à ce dernier par transport prépayé.
AUCUNE AUTRE GARANTIE EXPLICITE N’EST DONNÉE. PAR LES PRÉSENTES, TITAN SE DÉGAGE DE TOUTE AUTRE GARANTIE IMPLICITE,
INCLUANT, SANS TOUTEFOIS S’Y LIMITER, LES GARANTIES DE COMMERCIABILITÉ ET D’ADAPTATION À UN USAGE PARTICULIER, DANS LES
LIMITES PERMISES PAR LA LOI. LA DURÉE DES GARANTIES IMPLICITES NE POUVANT ÊTRE DÉCLINÉES SE LIMITE À LA PÉRIODE INDIQUÉE DANS
LA GARANTIE EXPLICITE. LES RESPONSABILITÉS DE TITAN NE SAURAIENT EN AUCUN CAS SE CHIFFRER À UN MONTANT SUPÉRIEUR À CELUI DU
PRIX D’ACHAT, ET CELLES RELATIVES AUX DOMMAGES CONSÉCUTIFS, ACCESSOIRES OU PARTICULIERS EN VERTU DE TOUTE GARANTIE SONT
ÉGALEMENT DÉCLINÉES, DANS LES LIMITES PERMISES PAR LA LOI.
TITAN NE DONNE AUCUNE AUTRE GARANTIE EXPLICITE ET DÉCLINE TOUTE GARANTIE IMPLICITE DE COMMERCIABILITÉ ET D’ADAPTATION
À UN USAGE PARTICULIER RELATIVEMENT AUX ACCESSOIRES, À L’ÉQUIPEMENT, AUX MATÉRIAUX OU AUX COMPOSANTS VENDUS MAIS
NON FABRIQUÉS PAR ELLE; CES ÉLÉMENTS (MOTEURS À ESSENCE, COMMUTATEURS, FLEXIBLES, ETC.) SONT PLUTÔT SOUMIS, LE CAS
ÉCHÉANT, AUX GARANTIES DE LEUR FABRICANT. TITAN S’ENGAGE À OFFRIR UN SOUTIEN RAISONNABLE AUX UTILISATEURS QUI FERONT DES
RÉCLAMATIONS RELATIVES À L’INOBSERVATION DE CES GARANTIES.
Titan Tool, Inc., (“Titan”) garantiza que en el momento de la entrega al comprador original para su uso (“Usuario final”), el equipo cubierto por esta garantía está
exento de defectos en material y fabricación. Con la excepción de cualquier especial, limitada, o extendido garantía publicado por Titan, la obligación de Titan
en virtud de esta garantía se limita a sustituir o reparar sin cargo las piezas que; a la entera satisfacción de Titan, demuestren estar defectuosas dentro de doce
(12) meses después de la venta al usuario final. Esta garantía corresponde solamente cuando la unidad se instala y funciona según las recomendaciones e
instrucciones de Titan.
Esta garantía no corresponde en el caso de daños o desgaste causados por abrasión, corrosión o uso indebido, negligencia, accidente, instalación errada,
sustitución de piezas con componentes que no sean Titan o alteraciones con la unidad de tal modo que se vea afectado el funcionamiento normal.
Las piezas defectuosas deben devolverse a un centro de ventas y servicio autorizado de Titan. Todos los cargos de transporte, incluso la devolución a la
fábrica, si es necesario, debe pagarlos previamente el usuario final. El equipo reparado o cambiado se devolverá al usuario final con porte prepagado.
NO EXISTE NINGUNA OTRA GARANTÍA EXPRESA. TITAN DESCONOCE POR LA PRESENTE TODA OTRA GARANTÍA IMPLÍCITA INCLUSIVE ENTRE
OTRAS, LAS DE COMERCIABILIDAD E IDONEIDAD PARA UN FIN PARTICULAR, EN LA MEDIDA QUE LO PERMITA LA LEY. LA DURACIÓN DE LAS
GARANTÍAS IMPLÍCITAS QUE NO PUEDEN DESCONOCERSE SE LIMITA AL PLAZO ESPECIFICADO EN LA GARANTÍA EXPRESA. EN NINGÚN CASO
EXCEDERÁ LA RESPONSABILIDAD DE TITAN EL MONTO DEL PRECIO DE COMPRA. LA RESPONSABILIDAD CIVIL POR DAÑOS Y PERJUICIOS
RESULTANTES, FORTUITOS O ESPECIALES BAJO TODA GARANTÍA QUEDA EXCLUIDA EN LA MEDIDA QUE LO PERMITA LA LEY.
TITAN NO OFRECE GARANTÍAS Y DESCONOCE TODA GARANTÍA IMPLÍCITA DE COMERCIABILIDAD E IDONEIDAD PARA UN FIN PARTICULAR
REFERENTE A ACCESORIOS, EQUIPO, MATERIALES O COMPONENTES VENDIDOS PERO NO FABRICADOS POR TITAN. AQUELLOS ARTÍCULOS
VENDIDOS, PERO NO FABRICADOS POR TITAN (COMO LOS MOTORES DE GAS, INTERRUPTORES, MANGUERAS, ETC.) ESTÁN PROTEGIDOS POR
LA GARANTÍA DE SU PROPIO FABRICANTE, SI LA HAY. TITAN PROPORCIONARÁ AL COMPRADOR ASISTENCIA RAZONABLE PARA EFECTUAR
RECLAMOS EN CASO DE INCUMPLIMIENTO DE ESTAS GARANTÍAS.
United States Sales & Service
Canadian Branch
International
Phone: 1-800-526-5362
Fax: 1-800-528-4826
Phone: 1-800-565-8665
Fax: 1-800-856-8496
Phone: 1-201-337-1240
Fax: 1-201-405-7449
200 Trowers Road, Unit 7B
Woodbridge, Ontario L4L 5Z8
1770 Fernbrook Lane
Minneapolis, MN 55447
1770 Fernbrook Lane
Minneapolis, MN 55447
www.titantool.com
28
© Titan Tool Inc. All rights reserved.