VISTA-128FBPN
Commercial Fire and Burglary
Partitioned Security System with Scheduling
Programming Guide
800-06308 4/10 Rev. B
Table of Contents
Relay Voice Descriptors and Custom Word
Substitutes Vocabulary........................................ 43
System Layout Worksheets.................................... 45
Output Devices Worksheets ................................... 57
Scheduling Menu Prompts ..................................... 63
Scheduling Worksheets.......................................... 64
Programming Field Settings for UL864 Compliance 2
Recommended Programming Procedure................. 8
Program Field Index ................................................. 9
VISTA-128FBPN Programming Form .................... 10
Partition-Specific Fields.......................................... 16
Programming With #93 Menu Mode ...................... 18
5800 Series Transmitters Loop Designations ........ 23
Alpha Descriptor Vocabulary.................................. 33
Programming Field Settings for UL864 Compliance
NOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING JURISDICTION, AND OTHER INVOLVED
PARTIES
This product incorporates field-programmable software. In order for the product to comply with the requirements
in the Standard for Control Units and Accessories for Fire Alarm Systems, UL 864, certain programming features
or options must be limited to specific values or not used at all as indicated below.
Program feature or option Permitted in Possible settings
Settings permitted in UL 864
UL864? Y/N
✱08 TEMPORAL SIREN
PULSE
N
0 = disable
1 = enable
Not used at this time. Must be set to
“0” (disable).
✱13 ALARM SOUNDER (BELL)
TIMEOUT
✱14 TRIGGER OR RS232
Y
Enter 01-15 multiplied by 2 minutes.
00 = no timeout.
0 = trigger
1 = RS232 input
0 = disable
1 = enable
Enter 01 - 09 for the first digit;
enter11 for “*” or 12 for “#” for the
second digit.
0 = disable
1 = enable
Must be set to “3” (Minimum of 6
minutes).
Must be set to “0”.
0 = disable
1 = enable
Enter 0001-9999 for the test report
interval in hours.
Enter 0000 for test reporting.
0 = disable
1 = enable
0 = disable
1 = enable
0 = EOLR supervision
1 = N.C. loops
Enter the wait time for dial tone
detection:
0 = 5 seconds; 1 = 11 seconds; 2 = 30
seconds.
Enter 00 to disable ring detection.
Enter 01-14 for ring counts of 1-14.
Enter 15 to select Answering Machine
Defeat Mode
Must be set to “0” (disable).
N
✱17 AC LOSS KEYPAD
SOUNDING
✱20 VIP MODULE PHONE
CODE
N
✱22 KEYPAD PANIC
ENABLES (PARTITION
SPECIFIC)
✱26 INTELLIGENT TEST
REPORTING
✱27 TEST REPORT INTERVAL
N
✱28 POWERUP IN PREVIOUS
STATE
✱37 DOWNLOAD COMMAND
ENABLES
✱41 NORMALLY CLOSED OR
EOLR (ZONES 3-8)
✱42 DIAL TONE PAUSE
Y
✱44 RING DETECTION
COUNT
N
N
Y
N
N
Y
N
–2–
Must be set to “1” (enabled).
Not used. Must be set to “00”.
Must be set to “000” for partition 1
in fire systems.
Must be set to “0024” (Maximum 24
hours)
Must be set to “1” (enable).
Must be set to “0” for all entries
(disable).
Must be set to “0” (EOLR
Supervision).
Must be set to “0” (5 seconds).
Must be set to “00” (disable).
Program feature or option
✱54 UNATTENDED MODE
✱56 DYNAMIC SIGNALING
DELAY
✱77 AUTO TROUBLE
RESTORE
✱80 ZONE TYPE RESTORES
FOR TYPES 9, 10 & 14
1✱12 PROGRAM
NOTIFICATION SIGNAL
1✱13 SYSTEM SENSOR
REVERSING RELAY
Permitted in
UL864? Y/N
N
Y
Y
N
Y
N
1✱18 AFFECTS LOBBY
N
1✱19 ARMS LOBBY
N
1✱22thru 1✱25 CROSS-ZONING
PAIRS (1 – 4)
1✱28 RF TRANSMITTER LOW
BATTERY SOUND
1✱29 RF TRANSMITTER LOW
BATTERY REPORTING
1✱30 RF RECEIVER
SUPERVISION CHECK-IN
INTERVAL
N
1✱31 RF TRANSMITTER
CHECK-IN INTERVAL
N
1✱35 ACCESS CONTROL
DIALER ENABLES
1✱44 WIRELESS KEYPAD
TAMPER DETECTION
1✱48 WIRELESS KEYPAD
ASSIGNMENT
1✱49 SUPPRESS TX
SUPERVISION SOUND
1✱53 DISABLE DOWNLOAD
CALLBACK
1✱57 5800 RF BUTTON
GLOBAL ARM
1✱58 5800 RF BUTTON FORCE
ARM
1✱60 ZONE 5 AUDIO ALARM
VERIFICATION
1✱72 EVENT LOG PRINTER
ONLINE
1✱73 PRINTER BAUD RATE
N
N
N
N
N
N
N
N
N
N
N
N
N
1✱76 CONTROL RELAY
(PART-SPECIFIC)
1✱78 EXTENDED HOME
CONT EVENTS
N
1✱79 HOME CONTROL
EVENTS
2✱07 AUTO-DISARM DELAY
(PART SPECIFIC)
N
N
N
Possible settings
0 = disable
1 = enable
Enter 00-15 times 15 seconds.
Settings permitted in UL 864
Must be set to “0” (disable).
Must be set to “6” (90 seconds).
0 = disable
1 = enable
0 = disable
1 = enable
0 = no
1 = yes
Must be set to “1” (enable).
0=use neither Zone 1 or Zone 2 inputs
1=use Zone 1 input;
2=use Zone 2 input;
3=use Zone 1 and Zone 2 inputs.
0 = disable
1 = enable
0 = disable
1 = enable
Enter 001-128
Enter 000,000 to disable
0 = disarmed state only
1 = both armed and disarmed states
0 = disable
1 = enable
Enter 02–15 times 2 hours (4–30
hours)
Enter 00 to disable receiver
supervision
Enter 02–15 times 2 hours (4–30
hours)
Enter 00 to disable transmitter
supervision
0 = disable
1 = enable
0 = disable
1 = enable
0 = none
1-8 = partition number
0 = disable
1 = enable
0 = callback required
1 = no callback required
0 = disable
1 = enable
0 = disable
1 = enable
0 = disable
1 = enable
0 = disable
1 = enable
0 = 1200
1 = 300
01-96 = relay number
00 = relay not used.
Not Used. Must be set to “0”.
1 = extended
0 = limited
0 = disable
1 = enable
00 = no delay.
01-14 times 4 minutes (04-56) delay.
15 = no auto disarming.
–3–
Must be set to “1” (enable) for zone
type 9.
Must be set to “1” (yes).
Must be set to “0” (disabled) for
partition 1.
Must be set to “0” (disabled) for
partition 1.
Must be set to “000,000” (disabled)
for fire zones.
Must be set to “1” (both armed and
disarmed states).
Must be set to “1” (enable).
Maximum is 02 (4 hours) for fire
installations.
Maximum is 02 (4 hours) for fire
installations.
Not used. Must be set to “0”.
Not used. Must be set to “0”.
Not used. Must be set to “0”.
Must be set to “0” (disable).
Must be set to “0” (callback
required).
Must be set to “0” (disable).
Must be set to “0” (disable).
Must be set to “0” (disable).
Not used. Must be set to “0”.
Not used.
Must be set to “00” (relay not used)
for partition 1.
Not used. Must be set to “0”.
Not used. Must be set to “0”in each
entry.
Must be set to “15” (no auto
disarming) for partition 1.
Program feature or option
Permitted in
UL864? Y/N
2✱18 ENABLE GOTO FOR
THIS PARTITION (partitionspecific)
2✱21 SUPERVISION PULSES
FOR COMMUNICATIONS
DEVICE
2✱22 DISPLAY FIRE ALARMS
OF OTHER PARTITIONS
2✱23 DISPLAY BURG, PANIC
AND CO ALARMS FOR OTHER
PARTITIONS
2✱24 DISPLAY TROUBLES OF
OTHER PARTITIONS
3✱01 EVENTS DISPLAY LOCK
N
0 = disable
1 = enable
Must be set to “0” (disable) for
partition 1.
N
0 = disable
1 = enable
Not used. Must be set to “00000”
(disable).
N
0 = disable
1 = enable
0 = disable
1 = enable
Must be set to “0” (disable) for
partition 1.
Must be set to “0” (disable) for
partition 1.
Must be set to “0” (disable) for
partition 1.
Must be set to “1” (enable).
3✱12 ZN TYPE 18 DELAY USE
N
3✱13 FIRE SUPERVISORY
RESPONSE TO OPEN/SHORT
(APPLIES TO ZONE TYPE 18)
3✱14 WATERFLOW ALARM
SILENCE OPTION
3✱16 DELAY FOR ZONE
TYPES 17 & 18
(Waterflow/Supervisory)
3✱18 EXTENDED DELAY FOR
ZONE TYPES 17 & 18 Multiplies
delay in 3*16 x 4)
3✱19 AUXILIARY INPUT
ALTERNATE FUNCTION
ENABLE
3✱20 TRIGGER OUTPUTS
FUNCTION SELECTION
3✱21 MAXIMUM NUMBER OF
DIALER ATEMPTS
3✱50 ZONE TYPE RESTORE
ENABLES FOR TYPES 16-18
3✱55 RESET ON SECOND OFF
FOR BELL 1
3✱56 RESET ON SECOND OFF
FOR BELL 2
3✱57 BELL 2 AND AX RELAY
CONFIRM ARMING DING
3✱59 ENABLE BELL 2 &
AUXILIARY RELAY CHIME
ANNUNCIATION
3✱60 BELL 2 & AUX RELAY
TIMEOUT
3✱82 BURGLARY FEATURES
ON PARTITION 1 ENABLE
RESTRICTION FOR FIRE
RELAYS
N
0 = disable
1 = enable
0 = disable
1 = enable
0 = disable
1 = enable
0 = Trouble on open/Supv on short
1 = Supv on open/Supv on short
0 = Silenced by User Code + OFF
1 = Silenced when zone restores
Enter 01-15 times 2 seconds
Enter 00 for no delay
Must be set to “0” (Silenced by User
Code + OFF).
Must be set to 00 (no delay).
N
0 = no extended delay
1 = multiply delay by 4
Must be set to 0 (no extended delay).
N
0 = disable
1 = enable
Must be set to 0 (disable).
N
0 = remote keypad sounder
1 = keyswitch LEDs
1-8
Must be set to 0 (remote keypad
sounder).
Must be set at 3, 4 or 5.
0 = disable
1 = enable
0 = disable
1 = enable
0 = disable
1 = enable
0 = disable
1 = enable
0 = disable
1 = enable
Must be set to “1” (enable).
N
N
N
N
N
Y
N
N
N
N
N
Y
N
Y
Possible settings
Enter 01-15 multiplied by 2 minutes.
00 = no timeout.
0 = disable
1 = enable
Yes
No
Settings permitted in UL 864
Must be set to “0” (disable).
Must be set to “0”.
Must be set to “0” (disable).
Must be set to “0” (disable).
Must be set to “0, 0” (disable).
Must be set to “0” (disable) if Bell 2
or Aux Relay is used for Fire.
Must be set to “3” (Minimum of 6
minutes).
Must be set to “0” (disable).
Restriction for # 70 must be set to
Yes when programming fire relays.
NOTE: When there is a conflict between UL864 and CP-01, UL864 will take precedence.
–4–
SIA CP-01 Quick Reference Chart
The minimum required system for SIA CP-01 is a UL Listed Control, Keypad and Bell.
Item
*09
*10
*11
*12
*28
*57
*84
*88
1*21
1*22 – 1*25
Feature
Range
Entry Delay # 1
02 – 15 multiplied by 15
seconds
00 = 240 sec (4
minutes)
Exit Delay #1
03 – 15 multiplied by 15
seconds
Entry Delay # 2
02 – 15 multiplied by 15
seconds
00 = 240 sec (4
minutes)
Exit Delay #2
03 – 15 multiplied by 15
seconds
Power Up in
0 = no
Previous State
1 = yes
Dynamic Signaling
0 = primary dialer
Priority
1 = Communicator as
first reporting destination
Swinger Suppression 01= 1 alarm
02= 2 alarms
Abort Window Time
1 = 15 seconds
(for non-fire zones)
2 = 30 seconds
3 = 45 seconds
Exit Time Reset
0=no
1=Resets Exit Delay to
programmed value
after zone is closed
and then faulted prior
to end of exit delay.
Cross Zoning
Zone 001 – 128
000, 000 = Disabled
1*42
Call Waiting Defeat
1*61
Abort Verify
Zone
Programming
Auto Stay
Zone, Zone
type 04 has
this feature
enabled by
default
Zone
Programming
(Abort
Window
Enable)
Auto Stay Arm or
Occupied Premises
Abort Window (for
non-fire zones)
0 = no
1 = yes
0 = Disable
1 = Enable
0 = Disable
1 = Enable
Shipping
Default
30 Seconds`
At least 30 Seconds **
60 Seconds
60 Seconds
30 Seconds
At least 30 Seconds **
60 Seconds
60 Seconds
Yes
Yes
0 (primary dialer)
0 (primary dialer)
1 alarm
1 alarm
30 Seconds
At least 15 Seconds **
1 (Enabled)
1 (Enabled)
Disabled
Enabled
Enabled and two (or
more) zones
programmed
Enabled if user has
call waiting
Enabled
1 (Enabled)
Enabled
1 = yes
Yes (all non-fire zones)
Disabled (0)
0 = no abort window
1 = yes, use abort
window according to
*88 selection
–5–
SIA Requirement*
Zone
Programming
(Swinger
Suppression
Enable)
Swinger Suppression
Enable
0 = no suppression
1 = yes, suppress
alarms according to
*84 selection
Yes (enabled)
Yes (enabled (all
zones))
Item
Feature
Range
Shipping
Default
SIA Requirement*
Zone
Programming
Tamper
Option
-
Fire Alarm
Verification
For Zone Response
Type 16 (Fire) tamper
selection must be set
to “0”
Always Enabled
Disabled
Enabled unless
sensors can self verify
Enabled
Enabled
5 minutes
Enabled
NA
Enabled
Not required to be
programmable
Enabled
Both zones must be
faulted within 5
minutes
NA
Per
Manufacturer
Per walk path in
protected premises
Disabled
Disabled
-
-
User
Authority
Level 6
Exit Time and
Progress
Annunciation/Disable
for Remote Arm (Not
Evaluated for SIA
CP-01)
Cancel Window
Cancel Annunciation
- Keypad displays
“Alarm Cancel”
when report is
received
Programmable Cross
Zoning Time
Duress Feature
* Programming at installation may be subordinate to other UL requirements for the intended application.
** In accordance with UL standards, the combined Entry Delay time and Abort Window cannot exceed 1 minute.
–6–
The purpose of this document is to provide a quick and easy way to program your entire system. A recommended
programming procedure is included, followed by a list of program fields with the corresponding program group they belong to
(system-wide, partition-specific, scheduling, etc.). Two program forms are included. One contains all the programming fields,
and the other contains the partition-specific fields. If you are setting up a single-partition system, the partition-specific fields
become system-wide fields.
Following the program forms are system layout worksheets. We recommend that you use these sheets to plan your system
before programming is performed. If you need further information about specific programming options, see the VISTA128FBPN Installation and Setup Guide.
Make sure that one two-line alpha keypad is connected to the control and is set to device address "00."
Single-Partition System
The system default is for a single-partition system. Use the VISTA-128FBPN SINGLE PARTITION PROGRAMMING
FORM when programming for single-partition usage. Follow the steps outlined in RECOMMENDED PROGRAMMING
PROCEDURE of this document for proper programming procedure.
Multiple-Partition System
You must enter the number of partitions you are using in data field 2*00 to set the system for multiple partitions. Use the
VISTA-128FBPN SINGLE PARTITION and the PARTITION-SPECIFIC PROGRAM FORMS when programming the
system for multiple partitions. Follow the steps outlined in RECOMMENDED PROGRAMMING PROCEDURE of this
document for proper programming procedure.
•
•
•
•
•
•
•
•
•
SUMMARY OF PROGRAMMING COMMANDS
To enter program mode, enter installer code + [8] + [0] + [0] + [0]
To set standard defaults, press ✱97
To change to next page of program fields, press ✱94
To return to previous set of fields, press ✱99
To erase account and phone number field entries, press [✱] + field number + [✱]
To assign zone descriptors, press #93 + follow menu prompts
To add custom words, press #93 + follow menu prompts
To enter Installer's Message, press #93 + follow menu prompts
To exit program mode, enter ✱99 OR ✱98: ✱99 allows re-access to programming mode by installer code.
✱98 prevents re-access to programming mode by installer code. The only way to re-access programming
mode is by depressing both the [✱] and [#] keys at the same time within 30 seconds of power-up.
Standard default (✱97) values are shown in brackets [ ], otherwise default = 0.
–7–
Recommended Programming Procedure
The following is a step-by-step procedure recommended for programming your VISTA-128FBPN system.
1. Set the keypads (and other peripheral devices) to the appropriate addresses.
2. Set factory defaults by pressing ✱97.
This will automatically enable keypad addresses 00-01, so be sure at least one keypad is set to one of these
addresses.
3. Program system-wide (global) data fields.
Using the programming form as a guide, enter program mode and program all system-wide programming
fields. These options affect the entire system, regardless of partitions. They include control options,
downloader and dialer options, RF options, event logging options, etc. Refer to the Program Field Index for a
listing of the program fields and their function.
Note that field 2✱00 (number of partitions) must be programmed before continuing.
4. Program partition-specific fields.
When the system-wide fields have been programmed, program all partition-specific programming fields by
first pressing ✱91 to select a partition (while still in data field program mode). Then enter the first partitionspecific field number ✱09. When you are finished, the next partition-specific field is automatically displayed.
Partition-specific fields can have different values for each partition. To program the fields for the next partition,
press ✱91, enter the desired partition number, then enter field ✱09. Refer to the MECHANICS OF
PROGRAMMING section in the VISTA-128FBPN Installation and Setup Guide for detailed instructions.
5. Use #93 Menu Mode for device programming.
Refer to Device Programming in this guide to assign keypad ID numbers and default partitions for each
keypad, and to selectively suppress certain keypad sounding options. Also use this mode to assign RF
receivers, relay modules, and Communicators (7845i-ent, 7845i-GSM, 7845GSM).
6. Use #93 Menu Mode for zone programming.
Refer to Zone Programming in this guide to program zone response types, assign right loop zones and
wireless zones, assign zones to partitions, and to program alarm report codes.
7. Use #93 Menu Mode for programming outputs.
Refer to Output Programming in this guide to program desired output operation.
8. Program Communication options.
Refer to System Communication section in the VISTA-128FBPN Installation and Setup Guide for detailed
instructions. Then use #93 menu mode to program report codes.
9. Use #93 Menu Mode for programming alpha descriptors.
Refer to Alpha Programming in this guide to enter zone and partition descriptors and a custom installer's
message.
10. Use #80 Mode for programming schedules.
Refer to the Scheduling Menu Prompts in the VISTA-128FBPN Installation and Setup Guide to program
open/close schedules, temporary and holiday schedules, limitation of access schedules, and time-driven
events.
11. Define user access codes.
Refer to User Access Codes in the VISTA-128FBPN Installation and Setup Guide to program authority level,
O/C reporting option, partition assignments, and wireless key assignments for each user.
12. Exit Programming Mode.
Exit programming mode by pressing either ✱98 or ✱99. Additional entries of ✱99 are required if the exit is
being done from fields 1✱00 and above.
To prevent re-access to programming mode using the Installer's code, use ✱98. The only way to re-access
programming mode is by depressing both the [✱] and [#] keys at the same time within 30 seconds of powerup.
Exiting by using ✱99 always allows reentry into programming mode using the Installer code. Either way of
exiting allows access via downloading. Note that if local programming lockout is set via downloading,
programming mode cannot be entered at the keypad.
–8–
Program Field Index
On the following pages, the programming fields have been arranged in numerical order. Use this index to cross-reference the
fields on the programming form.
Field
Group
Field Group
Field Group
*00
*04
*05
*06
*08
*09
*10
*11
*12
*13
*14
*15
*16
*17
*19
*20
*22
*24
*25
*26
*27
*28
*29
*30
*31
*32
*33
*34
*35
*36
*37
*38
*39
*40
*41
*42
*43
*44
*45
*46
*47
*48
*49
*50
*51
*52
*53
*54
*56
System-Wide
System-Wide
System-Wide
Partition-Specific
System-Wide
Partition-Specific
Partition-Specific
Partition-Specific
Partition-Specific
Partition-Specific
System-Wide
System-Wide
Partition-Specific
System-Wide
System-Wide
System-Wide
Partition-Specific
System-Wide
System-Wide
Communications
Communications
System-Wide
Partition-Specific
Communications
Communications
Partition-Specific
Communications
Communications
System-Wide
System-Wide
System-Wide
Partition-Specific
Partition-Specific
Communications
System-Wide
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
System-Wide
Communications
*57
*58
*59
*77
*79
*80
*83
*84
*85
*87
*88
*89
*90
1*11
1*12
1*13
1*15
1*17
1*18
1*19
1*21
1*22
1*23
1*24
1*25
1*26
1*28
1*29
1*30
1*31
1*33
1*34
1*35
1*42
1*43
1*44
1*47
1*48
1*49
1*53
1*55
1*56
1*57
1*58
1*60
1*61
1*70
1*71
1*72
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Partition-Specific
Partition-Specific
Partition-Specific
Partition-Specific
Communications
Partition-Specific
System-Wide
System-Wide
System-Wide
Communications
System-Wide
Partition-Specific
Partition-Specific
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
Partition-Specific
System-Wide
System-Wide
System-Wide
System-Wide
Communications
Communications
Communications
Communications
Partition-Specific
System-Wide
Partition-Specific
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
–9–
1*73
1*74
1*75
1*76
1*77
1*78
1*79
1*80
2*00
2*01
2*02
2*05
2*06
2*07
2*08
2*09
2*10
2*11
2*18
2*19
2*20
2*21
2*22
2*23
2*24
3*00
3*01
3*12
3*13
3*14
3*16
3*17
3*18
3*19
3*20
3*21
3*30
3*31
3*50
3*55
3*56
3*57
3*59
3*60
3*61
3*82
3*85
System-Wide
System-Wide
System-Wide
Partition-Specific
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
Partition-Specific
Partition-Specific
Partition-Specific
Partition-Specific
Partition-Specific
Partition-Specific
System-Wide
Partition-Specific
Partitioning
Partition-Specific
System-Wide
Partition-Specific
Partition-Specific
Partition-Specific
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
Partition-Specific
Partition-Specific
Partition-Specific
System-Wide
System-Wide
System-Wide
VISTA-128FBPN Programming Form
Some fields are programmed for each partition (shown as shaded fields). If you are programming a multiple-partition system,
see the Partition-Specific Fields section for programming these fields. Standard default (*97) values are shown in brackets [ ];
otherwise, default = 0.
*00 INSTALLER CODE
| | |
*17 AC LOSS KEYPAD SOUNDING
Enter 4 digits, 0-9 [5140]
[1]
1=enable; 0=disable
Must be "1" for Commercial Fire installations.
*04 ENABLE RANDOM TIMERS
*19 RANDOMIZE AC LOSS REPORT
1
2
3
4
5
6
7
8
Enter 1 to make available the randomizing of pre-programmed
time driven events for each partition. [0=disable].
Must be "0" for Commercial Burg installations.
*05 SYSTEM EVENTS NOTIFY
0= within 2 minutes; 1=10-40 min; 2=1-3 hours; 3=6-12 hours
without Type 13, 1-3 hours with Type 13.
*20 VIP MODULE PHONE CODE - Not used.
|
[0]
*06 QUICK EXIT
[1]
1=enable; 0=disable
*22 KEYPAD PANIC ENABLES
*08 TEMPORAL SIREN PULSE – Not Used at this time.
00 (240 seconds), 02-15 times 15 seconds
Maximum "03" for Commercial Burglary installations.
The entry delay time and Abort Window (field *88) combined
cannot exceed 60 seconds for SIA installations.
*10 EXIT DELAY #1
*24 IGNORE EXPANSION ZONE TAMPER
*25 BURG.TRIGGER FOR RESPONSE TYPE 8 [1]
03-15 times 15 seconds
Maximum "04" for Commercial Burglary installations.
Minimum 60 seconds “04” for SIA installations.
*11 ENTRY DELAY #2
1=enable; 0=disable
*26 INTELLIGENT TEST REPORTING
|
[02]
00 (240 seconds), 02-15 times 15 seconds (must be longer
than Entry Delay #1). Maximum "03" for Commercial Burglary
installations.
The entry delay time and Abort Window (field *88) combined
cannot exceed 60 seconds for SIA installations.
*12 EXIT DELAY #2
*28 POWER UP IN PREVIOUS STATE
[1]
1=enable; 0=disable
Must be “1” for Commercial Burglary and Commercial Fire
installations.
*29 QUICK ARM
[0]
[1]
1=enable; 0=disable
Enter 1 to set J2 Pin 5 as a RS232 input to enable system to
receive serial data (75 baud).
Enter 0 to enable J2 Pin 5 as fire alarm trigger.
Must be set to “0”.
*15 KEYSWITCH ASSIGNMENT
| | |
Enter interval in hours, 0001-9999; 0000=no report;
Max. 0024 for Commercial Burglary and Commercial Fire
installations.
01-15 times 2 minutes. Must be minimum 16 minutes for
Commercial Burglary installations. Must be minimum 6
minutes for Commercial Fire and SIA installations.
*14 TRIGGER OR RS232 INPUT
[0024]
*27 TEST REPORT INTERVAL
|
[03]
[0]
1=enable (no report sent if any other report was recently sent);
0=disable (send report at programmed interval, field *27)
Must be “0” for Commercial Burglary and Commercial Fire
installations.
|
[04]
03-15 times 15 seconds (must be longer than Exit Delay #1).
Maximum "04" for Commercial Burglary installations.
Minimum 60 seconds “04” for SIA installations.
*13 BELL 1 TIMEOUT
[0]
1=Ignore; 0=Enable tamper for RF and V-Plexs.
Must be "0" for Commercial Burglary and Commercial Fire
installations if using these devices.
|
[04]
[001]
1=enable; 0=disable
995 996 999
NOTE: Use for burglary panic types only. Do not use in
partition 1 in Fire systems.
|
[02]
|
Enter 01 - 09 for the first digit; enter
[00],
[11]
11 for “*” or 12 for “#” for the second digit.
Must be set to "00" for Commercial Burglary and Commercial
Fire installations.
1=yes, (messages sent via the RS232 port).
0=no, (no messages sent).
*09 ENTRY DELAY #1
[2]
*30 MAIN DIALER TOUCHTONE OR ROTARY
[1]
1=TouchTone; 0=rotary
*31 PABX ACCESS CODE
[0]
|
|
|
|
|
|
|
|
00-09; B-F (11-15)
Enter partition in which keyswitch used, 1-8; 9=silences
Notification Appliance Circuit if fire present; 0=disable
*32 PRIM. SUBS. ACCT #
Enter 00-09; B-F (11-15) [15 15 15 15]
*16 BELL 1 CONFIRMATION OF ARMING DING [1]
1=enable; 0=disable.
NOTE: If using a keyfob, when the button is pressed, either for
arming or disarming, the bell will ding indicating that the button
is working.
Must be "1" for Commercial Burglary installations.
– 10 –
*33 PRIMARY PHONE NUMBER
*46 LOW SPEED FORMAT (Primary)
[0]
0= ADEMCO Low Speed; 1=Sescoa/Radionics
*47 SECONDARY FORMAT
[1]
0=Low Speed; 1=Contact ID; 2= ADEMCO High Speed;
3= ADEMCO Express
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2-second pause
*48 LOW SPEED FORMAT (Sec.)
*34 SECONDARY PHONE NUMBER
[0]
0= ADEMCO Low Speed; 1=Sescoa/Radionics
*49 CHECKSUM VERIFICATION
[0] [0]
1=enable; 0=disable
*50 SESCOA/RADIONICS SELECT
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2-second pause
|
|
|
[0]
1=yes; 0=no If used with Spilt Reporting "1" option (1*34),
alarms and alarm restores go to both primary and secondary
numbers, while all other reports go to secondary only. If used
with Split Reporting "2" option, alarms and alarm restores go
to both, open/close and test messages go to secondary only,
while all other reports go to primary. If used with Split
Reporting “3” option, fire alarms and fire restores signals go to
both, all other reports go to secondary only.
*36 DOWNLOAD ID NO.
|
[0]
*51 DUAL REPORTING
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2-second pause
|
Sec
1=Sescoa; 0=Radionics
*35 DOWNLOAD PHONE NO.
|
Prim
|
|
*52 STANDARD/EXPANDED REPORT FOR PRIMARY
Enter 00-09; A-F (10-15) [15 15 15 15 15 15 15 15]
[0 0 0 0 0 0]
Alarm Rstr
*37 DOWNLOAD COMMAND ENABLES
0
Dlr ShtdwnSys ShtdwnNot UsedRmt BypRmt DisarmRmt ArmUpld PgmDwnld Pgm
See field 1*53 for Callback disable option; [1=enable];
0=disable. For Commercial Burglary and Commercial Fire
installations, all entries must be "0."
*38 PREVENT ZONE XXX BYPASS
[000]
*39 ENABLE OPEN/CLOSE REPORT FOR
O/C LoBat
[0 0 0 0 0 0]
Alarm Rstr
| |
Byp
Trbl
O/C LoBat
0=standard; 1=expanded;
NOTE: Expanded overrides 4+2 format.
*54 UNATTENDED MODE
[1]
[1]
0=disable, 1=enable, if automatic downloads will be allowed
Must be "0" for Commercial Fire installations.
INSTALLER CODE 1=enable; 0=disable
*40 OPEN/CLOSE REPORT FOR KEYSWITCH
[0]
*56 DYNAMIC SIGNALING DELAY
1=enable; 0=disable
*41 NORMALLY CLOSED or EOLR (Zones 3-8)
*42 DIAL TONE PAUSE
[0]
*57 DYNAMIC SIGNALING PRIORITY
[0]
[0]
*58 COMM CENTRAL STATION #1 CATEGORY ENABLE
[1]
1=wait for true dial tone; 0=pause, then dial
[0 0 0 0 0 0]
|
[00]
|
0=Primary dialer; 1=Communicator, as first reporting
destination.
NOTE: Must be set to “0” for SIA installations.
0=5 seconds; 1=11 seconds; 2=30 seconds.
Must be "0" Commercial Burglary and Commercial Fire
installations.
*43 DIAL TONE DETECTION
[03]
Select the delay time (00-15) times 15 seconds before sending
to second destination.
NOTE: When Communicator is used as a backup to the dialer,
the Dynamic Signaling Delay (*56) should be set to a minimum
of 1 minute.
1=N.C.loops; 0=EOLR supervision.
Must be "0" for Commercial Burglary and Commercial Fire
installations.
01-14; 15=answering machine; 00=no detection.
Must be "00" for Commercial Burglary and Commercial Fire
installations.
*45 PRIMARY FORMAT
Trbl
*53 STANDARD/EXPANDED REPORT FOR SECONDARY
001-128; 000 if all zones can be bypassed
*44 RING DETECTION COUNT
Byp
0=standard; 1=expanded;
NOTE: Expanded overrides 4+2 format.
Alarm Trbl
Byp
O/C
Syst
Test
0=disable, 1=enable for reports for primary subs ID of
communicator.
*59 COMM CENTRAL STATION #2 CATEGORY ENABLE
[1]
[0 0 0 0 0 0]
0=Low Speed; 1=Contact ID; 2=ADEMCO High Speed;
3= ADEMCO Express
Alarm Trbl
Byp
O/C
Syst
Test
0=disable, 1=enable for reports for secondary subs ID of
communicator.
– 11 –
*77 AUTO TROUBLE RESTORE
“manual bypasses” and will not be unbypassed upon
disarming the system.
Zones that were in a bypassed state at the time a System
Shutdown is sent from the Compass Downloading software
will be unbypassed when the System Shutdown is removed.
[1]
0=disable, 1=enable
*79 ZONE TYPE RESTORE ENABLES FOR ZONE TYPES
1*12 PROGRAM NOTIFICATION SIGNAL
1-8
1
2
3
4
5
6
7
[1]
1=yes; 0=no
Must be "1" for Commercial Fire installations.
8
1=enable; [0=disable]
1*13 SYSTEM SENSOR REVERSING RELAY – Not Used.
*80 FOR TYPES 9, 10 and 14
[0]
9
10
14
0=use neither Zone 1 or Zone 2 inputs; 1=use Zone 1 input;
2=use Zone 2 input; 3=use Zone 1 and Zone 2 inputs.
1=enable; [0=disable]
Restores must be set to “1” for Commercial Fire installations.
|
*83 FIRST TEST REPORT TIME
|
1*15 CANCEL VERIFY
|
[Day 00; hour 12; min 00]. Days 01-07, Hours 00-23, Min 0059; 00 in all boxes = instant (Day 01= Monday)
*84 SWINGER SUPPRESSION
|
[01]
[1]
0=disable, 1=enable alarm output pulse upon kissoff of
Cancel report. NOTE: Field 1✳52 must be enabled to send a
Cancel report to the central station.
NOTE: Cancel reports must be enabled in system group 1.
01= 1 alarm
02= 2 alarms
NOTE: Fire zones are exempt from this requirement.
Must be "00" (disabled) for Commercial Burglary installations.
1*17 LOBBY PARTITION
[0]
Enter the "common lobby" partition (1-8)
1*18 AFFECTS LOBBY
[0]
Enter 1 if this partition affects the common lobby;
Enter 0 if it does not.
Must be "0" for Commercial Burglary and Commercial Fire
installations.
*85 ENABLE DIALER REPORTS FOR PANICS & DURESS
1=enable; [0=disable]
995 996 999 Duress
*87 ENTRY WARNING
1*19 ARMS LOBBY
[1]
Enter 1 if arming this partition attempts to arm lobby;
Enter 0 if it does not.
Must be "0" for Commercial Burglary and Commercial Fire
installations.
1=continuous; 0=3 beeps
*88 ABORT WINDOW
[2]
1=15 seconds; 2=30 seconds; 3=45 seconds
Must be "0" for Commercial Burglary installations.
Must be “2” for SIA installations.
*89 ALARM RESTORE REPORT TIMING
1*21 EXIT DELAY RESET
Enter 00-09; B-F (11-15)
|
|
|
|
[15 15 15 15]
1*11 ZONE BYPASS AFTER DISARM
FIELDS 1✳22-1✳25: Allow four sets of two zones each to be linked
so that both must fault within a 5-minute period to cause an alarm.
Default for these fields = [000], [000].
1*22 CROSS-ZONING PAIR ONE
| |
| |
1*23 CROSS-ZONING PAIR TWO
| |
| |
1*24 CROSS-ZONING PAIR THREE
| |
| |
1*25 CROSS-ZONING PAIR FOUR
| |
| |
1*26 PANIC BUTTON OR SPEEDKEY
[00000000]
1
2
3
4
[1]
0=No; 1=Resets Exit Delay to programmed value after zone
is closed and then faulted prior to end of exit delay.
Must be "0" for Commercial Burglary installations. Exit Delay
must be enabled “1” for SIA installations.
[0]
0 = Restore is sent when zone is restored or at disarming,
whichever occurs first.
1 = Restore is sent at disarming whether zone is restored or
not, or at bell timeout, but only if restored.
2 = Restore is sent at disarming, whether the zone is restored
or not.
This field applies only to Burglary zone types. It does not
apply to Fire or Panic zone types.
Must be "2" for Commercial Burglary installations.
*90 SEC. SUBS. ACCT #
[0]
5
6
7
[00, 00, 00, 00]
8
|
|
|
|
A
B
C
D
Enter speedkey macro # (01-32) to use keys A-C for macro.
Otherwise enter 00 to use as panic. For D key, enter macro
# 01-32, or 00 to select macro when key is pressed.
1=enable; 0=disable
Enter 1 for each partition in which zones will remain
bypassed after disarm.
NOTES:
For each partition in which field 1✳11 is enabled, the USER
CODE + OFF will no longer unbypass zones. To unbypass
ALL zones, you must enter USER CODE + # + 64. To
unbypass zones INDIVIDUALLY, you must enter USER
CODE + 6 + zone number.
Any zone that was automatically bypassed by the system will
be unbypassed upon disarming of the system (e.g., STAY
mode, Auto-STAY, etc.).
Vent zones and zones bypassed by a programmed AutoBypass schedule (Timed Driven Event) are considered
1*28 RF TX LOW BATTERY SOUND
[0]
1=immediate; 0=when disarmed
Must be 1 for UL installations.
1*29 RF TX LOW BATTERY REPORTING
– 12 –
1=enable; 0=disable
Must be 1 for UL installations.
[0]
1*30 RF RCVR CHECK-IN INTERVAL
|
[02]
1*58 5800 RF BUTTON FORCE ARM
02-15 times 2 hours; 00 disables supervision
Maximum is 2 (4 hr) for UL installations.
1*31 RF XMITTER CHECK-IN INTERVAL
1=enable. If a zone is faulted after pressing button, console
will beep once. User should press button again within 4 sec.
to force bypass those zones. 0=disable.
Must be "0" for Commercial Burglary and Commercial Fire
installations.
|
[02]
02-15 times 2 hours; 00 disables transmitter supervision
Maximum is 2 (4 hr) for UL installations.
1*33 TOUCHTONE W/ROTARY BACKUP
1*60 ZONE 5 AUDIO ALARM VERIFICATION
[0]
[0]
Enter 1 if 2-way audio (AAV) is being used; Enter 0 if it is not.
Must be "0" for Commercial Burglary and Commercial Fire
installations.
1=enable; 0=disable
1*34 COMM. SPLIT REPORTING
[0]
[0]
1*61 ABORT VERIFY
0=no; 1=alarms and alarm restores primary, others
secondary; 2=open/close, test secondary, others primary;
3=fire alarms and fire restores to primary and secondary, all
others to secondary. See T51 for comments if using with
dual reporting.
NOTE: Split reporting should not be used with Dynamic
Signaling.
[1]
0=disable; 1=enable
Must be enabled “1” for SIA installations.
1*70 EVENT LOG TYPES
[1 0 0 0 1 0]
Alarm Chk
Byp
O/C
Syst
Test
1=enable; 0=disable
1*35 ACCESS CONTROL DIALER ENABLES - Not Used.
1*71 12/24 HOUR TIME STAMP FORMAT
[0]
0=12 hour; 1=24 hour
[0 0 0 0 0 0]
Trace Trbl
Byp Not Used Syst
1*72 EVENT LOG PRINTER ON-LINE - Not Used. Must Be
Alm
Set To “0”.
1=enable; 0=disable
Must Be Set To “0”.
1*42 CALL WAITING DEFEAT
[0]
[0]
0=disable; 1=enable
1=enable; 0=disable
1*43 PERM. KEYPAD BACKLIGHT
1*44
1*73 PRINTER BAUD RATE - Not Used. Must Be Set To
[0]
“0”..
1=enable; 0=disable, when disabled, display lights when any
key is pressed, and turns off after period of keypad inactivity.
WIRELESS KEYPAD TAMPER DETECTION – Not
Used. Must be set to “0”.
[0]
1=300; 0=1200
1*74 RELAY TIMEOUT XXX MINUTES [000]
[0]
1*47 CHIME ON BELL 1
[0]
1=enable; 0=disable
1*48 WIRELESS KEYPAD ASSIGNMENT - Not Used. Must
be set to “0”.
1*75 RELAY TIMEOUT YYY SECONDS [000]
0=disable; enter partition in which RF keypad used, 1-8.
[1]
1*76 CONTROL RELAY
1=disable; 0=enable.
Must be "0" for Commercial Burglary and Fire installs.
1*53 DOWNLOAD CALLBACK
1*55 EUROPEAN DATE FORMAT
1*56 AC 50/60 Hz CLOCK SPEED
1*77 LOG FIRST MAINTENANCE SIGNAL
1*78 EXTENDED HOME CONT EVENTS
[0]
Not Used. Must Be Set To “0”.
0=Limited home control command set (32 commands).
1=Extended home control command set (255 commands).
[0]
1=50 Hz; 0=60 Hz.
1*57 5800 RF BUTTON GLOBAL ARM
[0]
0=No Log; 1=Log first maintenance signal from each smoke
detector.
[0]
0=disable (mm/dd/yy); 1=enable (dd/mm/yy).
|
[00]
Relay will be pulsed for 2 seconds whenever code + [0] is
pressed. Enter relay number 01-96; 00=none.
Must be "00" for Commercial Burglary and Commercial Fire
installations.
[0]
1=callback not required; 0=callback required.
Must be "0" for Commercial Burglary and Commercial Fire
installations.
| |
Enter relay timeout, 0-127 seconds, desired for #80 Menu
Mode time driven event relay command numbers "05/10" and
#93 Menu Mode Output Programming command "57."
[0]
1*49 SUPPRESS TX SUPERVISION SOUND
| |
Enter relay timeout, 0-127 in multiples of 2 minutes, desired
for #80 Menu Mode time-driven event relay command
numbers "04/09" and #93 Menu Mode Output Programming
output command "56."
1=enable; 0=disable.
[0]
1=enable; 0=disable
Must be "0" for Commercial Burglary and Commercial Fire
installations.
– 13 –
1*79 HOME CONTROL EVENTS
2*18 ENABLE GOTO FOR THIS PARTITION
1=Allow log-on from other partitions; 0=disable
NOTE: Must be disabled for partition 1 in Commercial Fire
installations.
[0 0 0 0 0 0]
Alarm Trbl
Byp
O/C
Syst
Test
Not Used. Must Be Set To “0” In Each Entry.
1=enable; 0=disable. Select the type of events (status
reports) transmitted via the RS232 output.
1*80 LOG FAULTS AND RESTORES
[0]
2*19 USE PARTITION DESCRIPTORS
[0]
0=disable; 1=enable
[1]
2*20 ENABLE J2 TRIGGERS FOR PARTITION
0=Disabled
1=Enabled
[1]
0=disable; 1=enable for displayed partition
2*21 ENABLE SUPERVISION PULSES FOR LRR -
3rd Page Programming Fields (press *94)
Not Used. Must Be Set To “00000”.
2*00 NUMBER OF PARTITIONS
[1]
00000]
Enter 1-8
2*01 DAYLIGHT SAVING TIME [03, 11]
START/END MONTH
F
|
Start
End
[2, 1]
|
00-12; if no daylight saving time, enter 00,00
2*02 DAYLIGHT SAVING TIME
START/END WEEKEND
Start | End
Enter 1-7. 1=first; 2=second; 3=third; 4=fourth; 5=last; 6=next
to last; 7=3rd from last [1,5]
2*05 AUTO-ARM DELAY
This is the time during which the user is warned to exit the
premises prior to the auto-arming of the system (beeps every
15 seconds; "ALERT" displayed). Enter 01-15 minutes.
00=instant at end of arming delay.
2*07 AUTO-DISARM DELAY
|
[15]
2*23 DISPLAY BURG, PANIC and CO
0=disable; 1=enable.
Must be set to “0” (disable) for partition 1.
2*24 DISPLAY TROUBLES OF OTHER
[0]
PARTITIONS
0=disable; 1=enable
Must be set to “0” (disable) for partition 1.
[0]
3*00 DISPLAY TRBL INSTEAD OF CHECK
[0]
0=CHECK; 1=TRBL
3*01 EVENTS DISPLAY LOCK
[1]
0=scroll all alarms; 1=lock display of first fire alarm
NOTE: Must be set to “1” for Commercial Fire Installations.
2*09 OPEN/CLOSE REPORTS BY EXCEPTION [0]
1=enable; 0=disable
If enabled, only openings and closings occurring outside the
scheduled opening/closing windows will trigger dialer reports.
Opening reports will also be suppressed during the closing
window, in order to prevent false reports when the user arms
the system and then reenters the premises to retrieve a
forgotten item.
3*12 ZN TYPE 18 DELAY USE
[1]
0=disable; 1=enable
NOTE: Must be set to “0” for Commercial Fire Installations.
3*13 FIRE SUPERVISORY RESPONSE TO OPEN/SHORT
(Applies to Zone Type 18)
[0]
0=Trouble on open/Supervisory on short
1=Supervisory on open/Supervisory on short
NOTE: Must be set to “0” for Commercial Fire Installations.
[0]
ARMING/DISARMING WINDOWS
0=disable; 1=enable
See system-wide field 2*11 if enabling field 2*10. This
feature adds high security to the installation.
2*11 ALLOW DISARM OUTSIDE WINDOW
[0]
ALARMS OF OTHER PARTITIONS
0=disable; 1=enable
2*10 ALLOW DISARMING ONLY DURING
[0]
4th Page Programming Fields (press *94)
This is the time between the end of the disarming window
and the start of auto-disarming. Enter 01-14 times 4 minutes;
00=instant at end of window; 15=no auto-disarm.
2*08 ENABLE FORCE ARM FOR AUTO-ARM
T
OTHER PARTITIONS
|
[15]
S
0=disable; 1=enable.
Must be set to “0” (disable) for partition 1.
Enter the time between the end of the arming window and the
start of auto-arming warning period, in values of 1-14 times 4
minutes 00=instant; [15=no auto arm at all]. When this delay
expires, the Auto-Arm Warning Period begins.
2*06 AUTO-ARM WARNING PERIOD
P
2*22 DISPLAY FIRE ALARMS OF
|
[15]
B
Used only for supervised connection to non-ECP supported
LRR.
Enter 0 to disable or 1 to enable the listed outputs.
F= Fire; B= Burglary/Audible Panic; P= Silent Panic/Duress;
S= Supervisory; T= Trouble.
|
3*14 WATERFLOW SILENCE OPTION
[0]
0=silence on code = off; 1=silence when waterflow restores
NOTE: Must be set to “0” for Commercial Fire Installations.
[0]
IF ALARM OCCURS
Used only if field 2*10 is set to "1." If this field is enabled ("1")
the system can be disarmed outside the disarm window if an
alarm has occurred. If "0," disarming can only be done during
the disarm window. If field 2*10 is set to "0" for a partition,
this field has no effect for that partition.
3*16 DELAY FOR ZONE TYPE 17 & 18
|
[00]
Enter 00-15 times 2 seconds
Delay cannot exceed 90 seconds in UL installations.
NOTE: Must be "00" for Commercial Fire installations.
3*17 ALTERNATE FUNCTION (TAMPER)
FOR ZONE 6 0=disable; 1=enable
– 14 –
[0]
3*18 EXTENDED DELAY FOR TYPES 17 & 18
3*59 ENABLE BELL 2 & AUX RELAY
[0]
0=disable; 1=enable
NOTE: Must be "0" for Commercial Fire installations.
3*19 AUX INPUT ALTERNATE FUNC ENABLE
CHIME ANNUNCIATION
[0]
3*60 BELL 2 & AUX RELAY TIMEOUT
[0]
3*61 AUX RELAY FUNCTION
[8]
3*82 ENABLE BURG FEATURES ON PART 1
[1]
[1]
0=disable (disables AWAY, STAY, MAX, TEST, INSTANT
and CHIME); 1=enable;
NOTE: Must be "0" for Commercial Fire installations.
0=disable; 1=enable
Main Backup
NOTE: If 3*30 is disabled (0, 0), the panel does not report at
all via Communicator.
3*85 ENABLE FIRE & SYSTEM ZONE BYPASS [1]
[0]
0=disable; 1=only installer can bypass;
2=only installer and master can bypass.
Applies to fire zone types 9, 16, 17, and 18 and system
zones 970-977 and to partition 1 only.
1=TouchTone; 0=Rotary
3*50 ZONE TYPE RESTORE ENABLES
FOR ZONE TYPES 16-18
1=enable; [0=disable]
Restores must be set to “1” for Commercial Fire installs.
3*55 RESET ON SECOND OFF FOR BELL 1
[0]
0=disable; 1=enable
NOTE: Must be set to “0” for Commercial Fire Installations.
3*56 RESET ON SECOND OFF FOR BELL 2
[0]
0=disable; 1=enable
NOTE: Must be set to “0” for Commercial Fire Installations.
3*57 BELL 2 & AUX RELAY CONFIRM
|
0=trouble/supervisory; 1=alarm, silenced by code = off;
2=smoke detector reset; 3=battery save; 4=alarm, silenced
by code = # = 67
NOTE: See Data Field Descriptions in the Installation and
Setup Guide for specific information.
[1,0]
3*31 BACKUP DIALER TOUCHTONE/ROTARY
|
Bell 2
Aux
Enter 00-15 times 2 minutes; 00=no timeout [00,00]
Minimum 16 minutes for Commercial Burglary installations.
1-8 (3, 4 or 5 for NFPA72 compliant systems when a
secondary phone number is programmed (field *34))
3*30 DIALER SELECTION
Aux
NOTE: Must be “0, 0” if Bell 2 or Aux. Relay is used for fire
application.
0=Communicator full connection & remote console sounder;
1=Communicator limited connection and keyswitch LEDs
2=Communicator fire only connection and 5140LED
NOTE: Must be set to “0” for Commercial Fire Installations.
3*21 MAX NUMBER OF DIALER ATTEMPTS
Bell 2
0=disable; 1=enable
0=pins 5 and 9 function as per filed 3*20;
1=pins 5 and 9 function as RXD and DTR
NOTE: Must be set to “0” for Commercial Fire Installations.
3*20 TRIGGER OUTPUT SELECTION
[0,0]
[0,0]
ARMING DING
Bell 2 Aux
0=disable; 1=enable.
NOTE: If using a keyfob, when the button is pressed, either
for arming or disarming, the bell will ding indicating that the
button is working.
Must be “1” for Commercial Burglary installations.
– 15 –
Partition-Specific Fields
(Duplicate this page for each partition in the installation.)
To program these fields,
1. Press *91 to select a partition.
2. Enter a partition-specific field number (ex. *09).
3. Make the required entry.
4. Repeat steps 1-3 for each partition in the system.
PARTITION #____ PROGRAM FIELDS
1st Page Fields
*39 ENABLE OPEN/CLOSE REPORT
*06 QUICK EXIT
[1]
[1]
FOR INSTALLER CODE
1=enable; 0=disable
1=enable; 0=disable
*09 ENTRY DELAY #1
*84 SWINGER SUPPRESSION
|
[02]
01= 1 alarm
02= 2 alarms
NOTE: Fire zones are exempt from this requirement.
Must be "00" (disabled) for Commercial Burglary installations.
00 (240 seconds), 02-15 times 15 seconds
Maximum "03" for Commercial Burglary installations.
The entry delay time and Abort Window (field *88) combined
cannot exceed 60 seconds for SIA installations.
*10 EXIT DELAY #1
|
[04]
*85 ENABLE DIALER REPORTS FOR PANICS & DURESS
03-15 times 15 seconds
Maximum "04" for Commercial Burglary installations.
Minimum 60 seconds “04” for SIA installations.
*11 ENTRY DELAY #2
1=enable; [0=disable]
995 996 999 Duress
*87 ENTRY WARNING
|
[02]
|
[04]
[1]
1=continuous; 0=3 beeps
00 (240 seconds), 02-15 times 15 seconds (must be longer
than Entry Delay #1). Maximum "03" for Commercial Burglary
installations.
The entry delay time and Abort Window (field *88) combined
cannot exceed 60 seconds for SIA installations.
*12 EXIT DELAY #2
*88 ABORT WINDOW
[2]
1=15 seconds; 2=30 seconds; 3=45 seconds
Must be "0" for Commercial Burglary installations.
Must be “2” for SIA installations.
*90 SEC. SUBS. ACCT #
03-15 times 15 seconds
Maximum "04" for Commercial Burglary installations.
Minimum 60 seconds “04” for SIA installations.
Enter 00-09; B-F (11-15)
|
|
|
|
[15 15 15 15]
2nd Page Fields
1*18 AFFECTS LOBBY
*13 BELL 1 TIMEOUT
|
[03]
1*19 ARMS LOBBY
*16 BELL 1 CONFIRMATION OF ARMING DING [0]
1*26 PANIC BUTTON OR SPEEDKEY
[001]
1=enable; 0=disable
995 996 999
NOTE: Use for burglary panic types only. Do not use in
partition 1 in Fire systems.
*29 QUICK ARM
[00, 00, 00, 00]
|
|
|
[000]
|
1*43 PERM. KEYPAD BACKLIGHT
|
|
[0]
1=enable; 0=disable
When disabled, display lights when any key is pressed, and
turns off after period of keypad inactivity.
Enter 00-09; B-F (11-15) [15 15 15 15]
*38 PREVENT ZONE XXX BYPASS
|
A
B
C
D
Enter speedkey macro # (01-32) to use keys A-C for macro.
Otherwise enter 00 to use as panic. For D key, enter macro
# 01-32 or 00 to select macro when key is pressed.
[1]
1=enable; 0=disable
|
[0]
Enter 1 if arming this partition attempts to arm lobby; enter 0
if it does not
Must be “0” for Commercial Burglary and Commercial Fire
installations.
1=enable; 0=disable.
NOTE: If using a keyfob, when the button is pressed, either for
arming or disarming, the bell will ding indicating that the button
is working.
Must be "1" for Commercial Burglary installations.
*32 PRIM. SUBS. ACCT #
[0]
Enter 1 if this partition affects the common lobby; enter 0 if it
does not.
Must be set to “0” for Commercial Burglary and Commercial
Fire installations.
01-15 times 2 minutes. Must be set to a minimum 16 minutes
for Commercial Burglary installations. Must be minimum 6
minutes for Commercial Fire and SIA installations.
*22 KEYPAD PANIC ENABLES
|
[01]
| |
001-128; 000 if all zones can be bypassed
– 16 –
1*47 CHIME ON BELL 1
2*18 ENABLE GOTO FOR THIS PARTITION
[0]
1=enable; 0=disable
1*76 CONTROL RELAY FOR PART.
1=Allow log-on from other partitions; 0=disable
NOTE: Must be disabled (0) for partition 1 in Commercial
Fire installations.
|
[00]
Relay will be pulsed for 2 seconds whenever code + [0] is
pressed. Enter 00-96; 00=none.
Must be "00" for Commercial Burglary and Commercial Fire
installations.
2*20 ENABLE J2 TRIGGERS BY PARTITION
2*22 DISPLAY FIRE ALARMS OF
0=disable; 1=enable
Must be set to “0” (disable) for partition 1.
Enter the time between the end of the arming window and
the start of auto-arming warning period, in values of 1-14
times 4 minutes 00=instant; [15=no auto arm at all]. When
this delay expires, the Auto-Arm Warning Period begins.
2*06 AUTO-ARM WARNING PERIOD
2*23 DISPLAY BURG, PANIC AND CO ALARMS [0]
OF OTHER PARTITIONS
0=disable; 1=enable
Must be set to “0” (disable) for partition 1.
|
[15]
This is the time during which the user is warned to exit the
premises prior to the auto-arming of the system (beeps every
15 seconds; "ALERT" displayed). Enter 01-15 minutes.
00=instant at end of arming delay.
2*07 AUTO-DISARM DELAY
This is the time between the end of the disarming window
and the start of auto-disarming. Enter 01-14 times 4 minutes;
00=instant at end of window; 15=no auto-disarm
2*08 ENABLE FORCE ARM FOR AUTO-ARM
2*24 DISPLAY TROUBLES OF OTHER
0=disable; 1=enable
Must be set to “0” (disable) for partition 1.
4th Page Fields
3*57 BELL 2 & AUX RELAY CONFIRM
[0]
Bell 2 Aux
0=disable; 1=enable.
NOTE: If using a keyfob, when the button is pressed, either
for arming or disarming, the bell will ding indicating that the
button is working.
Must be set to “1” for Commercial Burglary installations.
2*09 OPEN/CLOSE REPORTS BY EXCEPTION [0]
2*10 ALLOW DISARMING ONLY DURING
3*59 ENABLE BELL 2 & AUX RELAY
[0, 0]
CHIME ANNUNCIATION
Bell 2 Aux
0=disable; 1=enable
NOTE: Must be “0, 0” if Bell 2 or Aux. Relay is used for fire
application.
[0]
ARMING/DISARMING WINDOWS
[0,0]
ARMING DING
0=disable; 1=enable
1=enable; 0=disable. If enabled only openings and closings
occurring outside the scheduled opening/closing windows
trigger dialer reports. Opening reports will also be
suppressed during the closing window, in order to prevent
false reports when the user arms the system and then reenters the premises to retrieve a forgotten item.
[0]
PARTITIONS
|
[15]
[0]
OTHER PARTITIONS
|
[15]
[1]
0=disable for displayed partition; 1=enable for displayed
partition
3rd Page Fields
2*05 AUTO-ARM DELAY
[0]
3*60 BELL 2 & AUX RELAY TIMEOUT
See system-wide field 2*11 if enabling field 2*10. This
feature adds high security to the installation.
0=disable; 1=enable
|
|
Bell 2
Aux
Enter 00-15 times 2 minutes; 00=no timeout [00, 00]
Minimum 16 minutes for Commercial Burglary installations.
SUMMARY OF PROGRAMMING COMMANDS
•
•
•
•
•
•
•
•
•
– 17 –
To enter program mode, enter installer code + [8] + [0] + [0] +
[0]
To set standard defaults, press *97
To change to next page of program fields, press *94
To return to previous set of fields, press *99
To erase account and phone number field entries, press [*] +
field number + [*]
To assign zone descriptors, press #93 + follow menu prompts
To add custom words, press #93 + follow menu prompts
To enter Installer's Message, press #93 + follow menu prompts
To exit program mode, enter *99 OR *98: *99 allows re-access
to programming mode by installer code. *98 prevents re-access
to programming mode by installer code.
Programming With #93 Menu Mode
NOTE: The following field should be preset before beginning: 2*00 Number of Partitions. In addition, receivers should
be programmed via Device programming.
After programming all system related programming fields in the usual way, press #93 while still in programming mode to
display the first choice of the menu driven programming functions. Press 0 (NO) or 1 (YES) in response to the displayed menu
selection. Pressing 0 will display the next choice in sequence.
#93 MENU MODE KEY COMMANDS
The following is a list of commands used while in the menu mode.
#93
Enters Menu mode
[Q]
Serves as ENTER key. Press to have keypad accept entry.
[#]
Backs up to previous screen.
0
Press to answer NO
1
Press to answer YES
001-009 All data entries are either 2-digit or 3-digit entries.
000
Exits menu mode, back into field programming mode, when entered at the first question for each category.
Menu selections are as follows:
PROMPT
EXPLANATION
ZONE PROG?
1 = YES 0 = NO
For programming the following:
• Zone Number
• Zone Response Type
• Partition Number for Zone
• Dialer report code for zone
• Input Device Type for zone (whether RF, polling loop, etc.)
• Enrolling serial numbers of 5800 Series transmitters & serial polling loop devices into the system.
• Zone Attributes (e.g., Arm w/Fault, Silent, etc.)
EXPERT MODE?
1 = YES 0 = NO
0
0
Same as Zone Programming except:
• Done with a minimum number of keystrokes.
• Can program wireless keys using pre-defined templates.
NOTE: Be aware some of the zone attributes cannot be programmed in the Expert Mode. These can only be
done in Zone Programming.
REPORT CODE PROG?
1 = YES 0 = NO
0
For programming the following:
• Alarm report codes for zones
• Restore & supervisory codes
• All other system report codes
ALPHA PROG?
1 = YES 0 = NO
For entering alpha descriptors for the following:
• Zone Descriptors
• Default Screen
• Custom Words
• Partition Descriptors
DEVICE PROG?
1 = YES 0 = NO
0
0
For defining the following device characteristics for addressable devices, including keypads, RF receivers
(5881ENHC), output relay modules (4204/4204CF), and Communicators (7845i-ent, 7845i-GSM, 7845GSM).
• Device Address
• Device Type
• Keypad Options (incl. partition assignment)
• RF House ID
• Communicator Options (incl. programming communicators)
For defining output relay functions.
OUTPUT PGM?
1 = YES 0 = NO
0
RLY VOICE DESCR?
1 = YES 0 = NO
0
Not Used. Must be set to “0”.
– 18 –
PROMPT
EXPLANATION
CUSTOM INDEX?
1 = YES 0 = NO
Not Used. Must be set to “0”.
0
ACCESS POINT PGM
1 = YES 0 = NO
0
Not Used. Must be set to “0”.
Not Used. Must be set to “0”.
ACCESS GRP PGM
1 = YES 0 = NO
0
Not Used. Must be set to “0”.
EVENT/ACTION PGM
1 = YES 0 = NO
0
SCHEDULED CHK-IN
1 = YES 0 = NO
0
For defining the schedule for the system to automatically call the downloader.
NOTE: Must be set to “0” for Commercial Fire installations.
Zone Programming
•
All Fire zones should be assigned to partition 1.
•
If using 5800 Series transmitters, do not the install batteries until you are ready to enroll them. After
enrolling the transmitter, the battery need not be removed. This is to prevent enrolling the wrong serial
number.
PROMPT
EXPLANATION
ZONE PROG?
1 = YES 0 = NO
0
SET TO CONFIRM?
1 = YES 0 = NO
ENTER ZONE NO.
000 = QUIT
0
010
Zone 010 entered ↑
010 ZT P RC In L
00 1 10 00 1
Press 1 to enter ZONE PROGRAMMING mode. The following screens appear. Press [✱] to display the next
screen. Press # to display a previous screen.
This prompt appears once upon entering Zone Programming Mode.
If “Yes,” Confirmation prompts will be displayed after the device’s Serial and Loop numbers have been
entered later.
Enter the 3-digit zone number to be programmed, as follows:
Protection Zones = 001–128
Relay Zones = 601–632 (use for relays on 4204CF modules only).
ECP Device Supervisory Zones = 800–830
System Supervisory Zones = 988, 990, 992 (duress), 997
Keypad Panic Zones = 995 (Do not use in Fire Alarm applications), 996, 999
Press [✱] to continue.
This display appears, showing a summary of the zone's current programming. ZT = Zone Type, P =
Partition, RC = Report Code, In = the input type of device, and L = the device's loop number to which the
sensor is connected.
Some devices can support more than one zone by means of individual loops (for example 5817CB, etc.). If
the zone is not programmed, the display appears as shown here. If you are checking a zone's programming,
and it is programmed satisfactorily, press [#] to back up one step and enter another zone number, if desired.
Press [✱] to continue.
– 19 –
PROMPT
EXPLANATION
010 ZONE TYPE
PERIMETER
Each zone must be assigned a zone type, which defines the way in which the system responds to faults in
that zone. Refer to the Zone Type Definitions section in the VISTA-128FBPN Installation and Setup Guide
for detailed definitions of each zone type. Enter the zone type desired (or change it, if necessary). Available
zone types are listed below.
03
Zone number 010 and
Zone Type 03 entry shown
† These are special zone
types used with 5800
Series Wireless
Pushbutton Units that
result in arming the system
in the STAY or AWAY
mode, or disarming the
system, depending on the
selection made.
00 = Assign for Unused Zones
01 = Entry/Exit #1, Burglary
02 = Entry/Exit #2, Burglary
03 = Perimeter, Burglary
04 = Interior Follower, Burglary
05 = Trouble Day/Alarm Night
06 = 24 Hr. Silent Alarm
07 = 24 Hr. Audible Alarm
08 = 24 Hr. Auxiliary (Not for Medical Use)
09 = Fire Without Verification
10 = Interior Delay, Burglary
12 = Panel Link Supervision – Not Used
13 = Remote P/S
14 = CO Detector Alarm
16 = Fire With Verification
17 = Waterflow
18 = Fire Supervisory
19 = 24-Hour Trouble
20 = Arm–STAY†
21 = Arm AWAY†
22 = Disarm†
23 = No Alarm Response (e.g., relay activation)
27 = Access Point – Not Used
28 = MLB Supervision (if VGM installed) – Not Used
29 = Momentary Exit (used with VistaKey module) - Not Used
Press [✱] to continue.
010 Arm w/ Fault?
1 = YES 0 = NO
0
010 Force Arming?
1 = YES 0 = NO
0
010 Vent zone ?
1 = YES 0 = NO
0
010 Vent Re-arm ?
1 = YES 0 = NO
1
010 STAY MODE
None
0
010 Auto-stay ?
1 = YES 0 = NO
0
If you selected response type 1, 2, 4, or 10, this prompt appears. Enter 1 to enable arming of the partition
with this zone faulted. The zone must be restored (see Force Arming, the next prompt) before the exit delay
expires otherwise the system starts the entry delay and must be disarmed, or an alarm occurs.
If you entered 1 (YES) at the previous prompt, this prompt appears. Enter 1 to enable the system to
automatically bypass the zone if it is faulted at the end of the exit delay.
If you enter 0 to disable and the zone is faulted at the end of exit delay, the system either performs the exit
error logic or an alarm occurs.
NOTE: Force Arming cannot be enabled for UL installations.
If you selected response type 3, this prompt appears. Enter 1 to enable the arming of the partition with this
zone faulted (force arm). The zone is automatically bypassed.
NOTE: The zone may be unbypassed simply by restoring the zone (e. g., closing the window), if the Vent
Re-arm option (next prompt) for the zone is enabled.
Enter 0 to disable.
Press [✱] to continue.
If you entered 1 (YES) at the previous prompt, this prompt will appear. Enter 1 to enable the system to
automatically unbypass the zone when it is restored (e.g., by closing the window).
Enter 0 to disable. The zone is bypassed for the duration of the armed period regardless of the zone status.
Press [✱] to continue.
If you selected response type 1, 2, 3, 4, 5, or 10, this prompt will appear. Enter the STAY mode for this
zone (0-2).
0 = None. The zone is not bypassed when the partition is armed STAY.
1 = Stay 1. The zone is automatically bypassed when the user enters [User Code] + [3] (STAY) + [1].
2 = Stay 2. The zone is automatically bypassed when the user enters [User Code] + [3] (STAY) + [2].
NOTES:
0 (None) cannot be selected for response types 4 and 10.
Response types 4 and 10 are defaulted for STAY mode 1.
If the user enters [User Code] + [3] (STAY) + [3], all zones assigned to Stay mode 1 and 2 in the partition
are automatically bypassed.
If none of the zones in the partition are assigned to Stay mode 2, then when the user enters [User Code] +
[3] (STAY), all zones assigned to Stay mode 1 are automatically bypassed.
Press [✱] to continue.
If you selected response type 1, 2, 3, 4, 5, or 10, this prompt will appear. Enter 1 to enable. The zone is
automatically bypassed if none of the entry/exit zones are opened during the exit delay time (no one exits the
premises). Enter 0 to disable.
NOTES: All zones enabled for auto-stay except types 3 and 5 have exit delay time when the partition is
armed. If auto-stay is enabled, make sure at least one zone is programmed for entry/exit in the same
partition, otherwise this zone will be automatically bypassed every time the partition is armed.
Press [✱] to continue.
– 20 –
PROMPT
EXPLANATION
010 Silent ?
1 = YES 0 = NO
1
If you selected response type 1, 2, 3, 4, 5, or 10, this prompt will appear. Enter 1 to enable. The zone
follows all the selected response type’s characteristics, except in the alarm condition, the alarm output and
the keypad sounder do not sound and the keypad does not display the alarm condition.
Enter 0 to disable.
Press [✱] to continue.
010 Bypass Group
01-15
01
If you selected response type 1, 2, 3, 4, 5, or 10, this prompt will appear. Enter the bypass group for the
zone (01–15). This enables the user to bypass a group of zones by entering [User Code] + [6] (Bypass) +
[✱] + [Group No.] (01-15).
Enter 00 for None.
Press [✱] to continue.
1
Enter the partition number (1–8) you are assigning this zone to.
Press [✱] to continue.
010 Abort Window
1 = YES 0 = NO
1
0 = No abort window.
1 = Yes, use abort window according to field *88 selection.
010 Swinger Sup?
1 = YES 0 = NO
1
0 = No suppression.
1 = Yes, suppress alarms according to field *84 selection.
010 Partition
010 REPORT CODE
1st 03 2nd 12
3C
010 BELL/RLY SEL
0
010 INPUT TYPE
RF Xmitter
Input types 4 & 5 are
valid for certain 5800
Series transmitters only
If using input type 02
with a door/window type
transmitter, only loop 1
may be used.
010 SMART CONTACT
1 = YES 0 = NO
3
Enter the report code. The report code consists of 2 hexadecimal digits, each in turn consisting of 2
numerical digits. For example, for a report code of "3C," enter 03 for "3" and 12 for "C."
(Refer to the System Communication section in the Installation and Setup Guide for more information about
report codes and reporting formats.)
Press [✱] to continue.
Each zone can be assigned to activate either one or both Notification Appliance Circuits and/or the system’s
auxiliary relay. Enter one of the following assignments:
0=none; 1=bell 1; 2=bell 2; 3=bell 1 & bell 2; 4=aux relay; 5=bell 1 & aux relay; 6=bell 2 & aux relay; 7=bell 1
& bell 2 & aux relay.
Press [✱] to continue.
Enter the input device type as follows:
00 = not used
01 = hardwired
02 = RF motion (RM type)
03 = supervised RF transmitter (RF type)
04 = unsupervised RF transmitter (UR type)
05 = RF button-type transmitter (BR type)
06 = serial number polling loop device (SL type)
07 = DIP switch-type polling loop device
08 = right loop of DIP switch type device
09 = keypad input (code + #73)
Right loops refer to the use of the right loop on a 4190WH Zone Expander Module and/or 4278EX PIR,
which allow hardwired devices to be monitored by the polling loop.
If you are programming hardwired or DIP switch polling loop devices, the summary display appears after
completing this entry.
NOTE: After programming, refer to the Installation and Setup Guide test section for testing of the RF
devices.
Press [✱] to continue.
If input type 3 or 6 was selected, this prompt will be displayed. Enter 1 for devices that monitor maintenance
signals (ex. 5193SD, 5193SDT) or can be used to limit fault signals in the disarmed state (ex. Quest
2260SN). Otherwise, enter 0.
NOTES:
1. The Smart Contact option must ONLY be selected for devices that support the feature, otherwise
unpredictable results may occur.
2. if using the new 5193SD/SDT V-Plex smoke detectors (or older 5192SD/SDT with the maintenance DIP
sw enabled) the "Smart" option must be selected in zone programming or when they enroll unpredictable
results may occur if the smoke goes into a High Sens or Low Sens condition.
– 21 –
PROMPT
EXPLANATION
001 Tamper Option
none
If you selected input type 1, 6, 7, or 8, this prompt displays. If the zone has a tamper switch wired in the
loop in addition to a sensor contact, enter the tamper option.
Enter 1 if the tamper switch is normally closed (wired in series) with the EOL resistor.
Enter 2 if the tamper switch is normally open (wired in parallel) with the EOL resistor.
Enter 0 if a tamper switch is not being used in the loop.
NOTE: For zone response types 9 or 16 (Fire), the tamper selection must be “0” none.
0
010 V-PLEX RELAY?
1 = YES 0 = NO
If you selected input type 6, this prompt is displayed. Enter 1 if using a 4101SN Relay Module for this
zone. Otherwise enter 0.
Press [✱] to continue.
010 CONS ECP ADDR
(00-30)
01
If you selected input type 09, this prompt is displayed. Enter the ECP address of the keypad that is being
used for entry/exit for this access point (00-30).
Press [✱] to continue.
010 ACCESS POINT
(01-15)
01
If you selected input types 06 this prompt is displayed. Enter the access point (01-15) to be controlled by
the input type.
NOTE: For input type 06, the selected address must be 00.
Press [✱] to continue.
010 INPUT S/N:
AXXX-XXXX
L
1
For Serial Number entry and Loop Number entry, do one of the following:
a. Transmit two open and close (or close and open) sequences. For a button-type transmitter, press and
release the button, wait approximately 4 seconds, then press and release the button a second time.
OR
b. Manually enter the 7-digit serial number printed on a label on the transmitter, using the Alpha keypad.
Then press the [✱] key, the cursor moves to the “L” position. You can edit the loop number, if necessary.
When the loop number is acceptable, press [✱].
OR
c. Press key [C] to copy the last serial number enrolled (used when programming a transmitter with several
input loops).
Press [✱] to accept.
010 INPUT S/N:
A022-4064
L
1
The cursor will then move to the Loop column (L) with the previously entered/transmitted serial number
displayed.
Enter the loop number (refer to 5800 Series Transmitters Loop Designations below).
To Delete an Existing Serial Number, enter “0“ in the loop number field. The serial number will change to
“0”s.
If “0” was entered in error, simply re-enter the loop number or press [#], and the serial number will return to
the display.
Press [✱] to accept.
010 INPUT S/N:
A022-4064
L
1
The system will then check for a duplicate serial/loop number combination.
If a duplicate serial/loop number combination is found, the keypad will emit a single long beep, and display
the serial number along with a “?” for the loop number, allowing you to re-enter the correct loop number.
If the serial/loop number combination is not a duplicate in the system, a display appears showing the serial
number and loop number entry.
Press [✱] to continue.
– 22 –
5800 Series Transmitters Loop Designations
PROMPT
EXPLANATION
XMIT TO CONFIRM
PRESS ✱TO SKIP
Confirmation Option: This prompt only appears if you answered “Yes” at the first prompt. The system
enters a confirmation mode so that the operation of the actual programmed input can be confirmed. Activate
the loop input or button that corresponds to this zone. At any time during this step, you may press the [✱] key
on the keypad to save the serial and loop number combination without confirming.
Entd
Rcvd
A022-4063
A022-4064
1
If the serial number transmitted does not match the serial number entered, a display similar to the one
at the left appears. If the loop number does not match, it is also displayed.
If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary
display does not appear), press the [#] key twice and then enter or transmit the correct serial number.
010 ZT P RC In L
03 1 3C RF 1s
If the serial number transmitted does match the serial number entered, the system beeps 3 times and a
summary display appears, showing that zone’s programming. Note that an “s” indicates that a transmitter’s
serial number has been enrolled.
Press [✱] to accept the zone information.
ENTER ZONE NO.
000 = QUIT
011
The system now returns to the “ENTER ZONE NO.” prompt for the next zone.
When all zones have been programmed, enter “000” to quit.
After you have enrolled each wireless device, remove ONE of the serial number labels from that device and affix it in
the appropriate column on the worksheets provided later in this Programming Guide; then enter the other information
(zone number, zone type, etc.) relevant to that device.
When you have finished programming all zones, test each using the system's Test Mode. Do not use the
Transmitter ID Sniffer Mode. The system checks only for transmission of one zone on a particular
transmitter, NOT the zones assigned to each additional loop, and also does not verify polling loop type
zones.
– 23 –
Expert Mode Zone Programming
Expert mode allows you to program zones using the minimum number of screens and keystrokes.
Expert Mode Zone Programming does not provide the capability to program some of the zone’s attributes,
such as Arm w/Fault, Vent Zone, STAY mode, Auto-STAY, Bypass Group, etc. If you want to program a
zone for any of these attributes, you must use Zone Programming.
Enter the Programming mode with [Installer Code] + 8 0 0 0
Before programming your zones, do the following:
1. Program field 2✱00: Number of Partitions.
2. Enable your RF Receiver in Device Programming menu mode.
To program your zones, press ✱93 to display the "ZONE PROG?" prompt. Enter “0” (NO) to each prompt until the “EXPERT
MODE?” prompt appears.
PROMPT
EXPLANATION
EXPERT MODE?
1 = YES 0 = NO
Press 1 to enter Expert mode.
0
SET TO CONFIRM?
0 = NO 1 = YES
0
Zn ZT P RC In
001 03 1 10 HW
L
-
This prompt appears once upon entering Expert Mode.
If you select “Yes,” Confirmation prompts will be displayed after the device’s Serial and Loop numbers have
been entered later.
A summary display appears, showing zone 1’s current programming or default values.
Zn ZT P RC In
L
010 03 1 10 RF 1s
Enter the desired 3-digit zone number and press [✱].
NOTE: If you want to exit the Expert mode, enter “000” + [✱].
If an “s” appears after the loop number, it indicates that the transmitter’s serial number has been enrolled.
Use the [D] key to enter and duplicate wireless keys (see “Entering Wireless Keys” later)
Zn ZT P RC In L
010 03 1 10 RF -
Enter all zone information except for Loop number, or press “C” to copy the zone information on this screen
from the last saved zone (including Loop).
ZT = Zone Type
P = Partition
RC = Report Code
In = Input Device Type
L = Loop number to which the sensor is connected.
NOTE: Pressing the [C] copies the zone information from the last saved zone, which includes the
input type. Verify this information is correct for this zone.
On this screen:
•
•
Use the [A] key to move to the right.
Use the [B] key to move to left and to back up to “ZT” field.
Press [✱] to accept the existing or newly-entered zone information.
– 24 –
PROMPT
EXPLANATION
ZN B M V A C E AD
010 2 1 1 0 1 1 01
Enter the remainder of the zone’s information, or press the [C] key to copy the zone attributes on this screen
from the last saved zone.
B = Bell/Relay Assignment
M = Maintenance (only used if “In” = 3 or 6)
V = Do Not Use. Must be set to “0”.
AC = Access Point (only used if In = 6)
E = Do Not Use. Must be set to “0”.
AD = Address (only used if “In” = 9)
If “In” = 9, enter the Device Address
NOTE: Pressing the [C] copies the zone attributes from the last saved zone. Verify the attributes for
this zone are correct.
On this screen:
•
•
Use the [A] key to move to the right.
Use the [B] key to move to left and to back up to “V” field.
Press [✱] to accept existing information.
010 INPUT S/N:
A XXX-XXXX
If you entered RM, RF, BR, UR or SL for the Input Type, this screen displays. Otherwise the summary
screen for the next zone displays.
Enter the 7-digit serial number, using one of the following methods:
a. Transmit two open and close (or close and open) sequences. For a button-type transmitter, press and
release the button, wait approximately 4 seconds, then press and release the button a second time.
OR
b. Manually enter the 7-digit serial number printed on a label on the transmitter, using the alpha keypad.
Then press the [✱] key, the cursor will move to the “L” position. You can edit the loop number, if
necessary. When the loop number is acceptable, press [✱].
OR
c. Press key [C] to copy the last serial number enrolled (used when programming a transmitter with several
input loops).
Remember, you can use the [A] key to move to the right or the [B] key to move to the left.
You can also use the [#] key to back up without saving.
L
-
010 INPUT S/N:
A022-4064
L
1
Press [✱] to accept the serial number and advance to the “L” position (if method “a” or “c” was used), then
enter the loop number.
If necessary, press the [#] key to back up without saving, and re-enter or edit the serial number before
pressing [✱] to save
The system checks for a duplicate. If a duplicate serial/loop number combination is found, the keypad will
emit a single long beep, and display the serial number along with a “?” for the loop number, allowing you to
re-enter the correct loop number.
010 INPUT S/N:
A000-0000
L
1
To Delete an Existing Serial Number, enter “0“ in the loop number field. The serial number will change to
“0”s.
If “0” was entered in error, simply re-enter the loop number or press [#], and the serial number will return to
the display.
The prompt to confirm appears. This prompt only appears if you answered “Yes” at the “SET TO
CONFIRM?” prompt.
The system enters a confirmation mode so that the operation of the actual programmed input can be
confirmed. Activate the loop input or button that corresponds to this zone. At any time during this step, you
may press the [✱] key on the keypad to save the serial and loop number combination without confirming.
XMIT TO CONFIRM
PRESS ✱TO SKIP
Entd
Rcvd
Zn
011
A022-4063
A022-4064
ZT
00
P
1
RC
10
1
In L
00 1
If the serial number transmitted does not match the serial number entered, a display similar to the one
at the left appears. If the loop number does not match, it also is displayed.
If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary
display for the next zone does not appear), press the [#] key twice and then enter or transmit the correct
serial number.
Activate the button on the wireless key again after re-entering the serial number.
If the serial number transmitted matches the serial number entered, the system beeps 3 times and
advances to the summary display for the next zone's programming.
After all the zones have been programmed, enter 000 for the zone number to quit.
After you have enrolled each wireless device, remove ONE of the serial number labels from that device and affix it in
the appropriate column on the worksheets provided later in this Programming Guide; then enter the other information
(zone number, zone type, etc.) relevant to that device.
– 25 –
Report Code Programming
All report codes are entered using #93 Menu Mode Programming, either through Report Code Programming, or through Zone
Programming while entering other zone information. In the VISTA-128FBPN, reports are divided into six categories. These
categories represent the main menu options in Report Code Programming. Reports and the categories in which they are
found are as follows:
ALARM CODES
Zone Alarm Reports
SYSTEM GROUP #2
Arm STAY
Time Set, Log Reset
Dialer Queue Overflow
Exit Error by Zone
Recent Close
RESTR, SUPV. CODES
(for groups of 16 zones)
Alarm Restore
Trouble
Trouble Restore
Bypass
Bypass Restore
SYSTEM GROUP #3
Early Open
Early Close
Late Open
Late Close
Failed to Open
Failed to Close
Auto-Arm Failed
Schedule Change
SYSTEM GROUP #1
Closing (arm AWAY)
Opening (disarm)
System Low Battery
Low Battery Restore
AC Loss
AC Restore
Periodic Test
Power
Cancel
Program Tamper
SYSTEM GROUP #4
Fire Walk-Test Start
Fire Walk-Test End
Off-Normal
The programming sequence that follows assumes that you will be entering all reports for the system at one time. In actuality,
you may skip from one main menu option to another by pressing 0 (N) at each main menu option. Main menu options are
highlighted in bold text. To enter report codes, do the following:
Enter Program Mode: [Installer Code] + 8 0 0 0. Then press #93. Enter 0 (N) at each main menu option until the Report
Code Programming option is displayed.
PROMPT
EXPLANATION
REPORT CODE PROG
1 = YES 0 = NO
0
Press 1 (Y) to enter to Report Code Programming.
Zone Alarm Reports
PROMPT
ALARM, ID DIGIT?
1 = YES 0 = NO
EXPLANATION
Press [1] (Y) to enter Alarm Report Codes for zones. Press [0] (N) to skip to the next main menu option.
0
ENTER ZONE NO.
000 = QUIT
001
Enter the zone number for which you are entering the report code.
Press [✱] to continue.
001 REPORT CODE
1st 00 2nd 00
00
Enter the first digit of the Alarm report code (double-digit entry) and press [✱]. Enter the 2nd digit of the
Alarm Report code.
Press [✱] to continue.
ENTER ZONE NO.
000 = QUIT
001
Enter the zone number for which you are entering the report code. When all zone Alarm Codes have been
programmed, enter 000 to Quit.
Press [✱] to continue.
QUIT REPORT MENU
1 = YES 0 = NO
0
If you have completely finished entering report codes, press [1] (Y) to quit Report Code Programming. If you
wish to enter other system report codes, enter 0 (N).
Press [✱] to continue.
– 26 –
Restore/Supervisory Codes
PROMPT
EXPLANATION
RESTR, SUPV. CODE
1 = YES 0 = NO
0
Press [1] (Y) to enter Restore and Supervisory Codes for zones.
ENTER ZN FOR GRP
000 = QUIT
001
Enter one zone for each group of 16 zones (001-016, 017-032, etc.).
ALARM RESTORE
GRP 001-016
00
Enter the first digit of the Alarm Restore Report Code for this group of zones (double-digit entry). The
second digit (for two-digit reporting formats) is automatically the ID (second) digit of the Alarm Report Code
for each zone (if programmed).
Press [✱] to continue.
TROUBLE
GRP 001-016
00
Enter the first digit of the Trouble Report Code for this group of zones (double-digit entry). The second digit
(for two-digit reporting formats) is automatically the ID (second) digit of the Alarm Report Code for each zone
(if programmed).
Press [✱] to continue.
TROUBLE RESTORE
GRP 001-016
00
Enter the first digit of the trouble restore code (single-digit entry) and press [✱]. The second digit (for twodigit reporting formats) is automatically the ID (second) digit of the alarm report code for each zone (if
programmed).
Press [✱] to continue.
BYPASS
GRP 001-016
00
Enter the first digit of the Bypass Report Code (double-digit entry) and press [✱]. The second digit (for twodigit reporting formats) is automatically the ID (second) digit of the Alarm Report Code for each zone (if
programmed).
Press [✱] to continue.
00
Enter the first digit of the Bypass Restore Report Code (double-digit entry) and press [✱]. The second digit
(for two-digit reporting formats) is automatically the ID (second) digit of the Alarm Report Code for each zone
(if programmed).
Press [✱] to continue.
ENTER ZN FOR GRP
000 = QUIT
017
Enter one zone for each group of 16 zones. When you are finished entering Restore and Supervisory Codes
for all zone groups, enter 000.
Press [✱] to continue.
QUIT REPORT MENU
1 = YES 0 = NO
If you have completely finished entering report codes, press [1] (Y) to quit Report Code Programming. If
you wish to enter other system report codes, enter 0 (N).
Press [✱] to continue.
BYPASS RESTORE
GRP 001-016
0
System Group #1 Codes
PROMPT
EXPLANATION
SYSTEM GROUP #1?
1 = YES 0 = NO 0
To enter System Group #1 codes, press 1 (Y).
CLOSE
1st 00
Enter the first digit of the Closing (Arm-AWAY) report. Press [✱]. Enter the second digit of the report. If the
user number is desired as the second digit, enter 01 (not necessary for Contact ID or High Speed formats).
Press [✱] to continue.
2nd 00
– 27 –
PROMPT
EXPLANATION
Enter the rest of the codes in the same manner. Other report codes in System Group #1 are:
•
Opening (Disarm) Also, enable this if you desire Callback Requested reports (the panel answers a
phone call from the downloader).
•
System Low Battery
•
Low Battery Restore
•
AC Loss
•
AC Restore
•
Periodic Test
•
Power
•
Cancel – Starting at the end of the Abort Window the period of time in which a user can cancel the
alarm is 5 minutes. If an alarm has been previously transmitted, a cancel signal is transmitted if either
the alarm system is disarmed or both a disarm and a function key is depressed during the Cancel
Window. Additionally, when an alarm cancel has been sent on the keypad within the 5 minutes, the bell
will ding momentarily.
•
Program Tamper
Once you have entered these report codes, the system prompts you with the Quit menu.
QUIT REPORT MENU
1 = YES 0 = NO
0
If you have completely finished entering report codes, press 1 (Y) to quit Report Code Programming. If you
wish to enter other system report codes, enter 0 (N).
Press [✱] to continue.
System Group #2 Codes
PROMPT
EXPLANATION
SYSTEM GROUP #2 ?
1 = YES 0 = NO 0
To enter System Group #2 codes, press [1] (Y).
STAY
1st 00
Enter the first digit of the Arm-STAY report. Press [✱]. Enter the second digit of the report. If the user
number is desired as the second digit, enter 01 (not necessary for Contact ID or High Speed formats).
Press [✱] to continue.
2nd 00
Enter the rest of the codes in the same manner. Other codes in System Group #2 are:
•
Time Set, Log Reset
•
Dialer Queue Overflow
•
Exit Error by Zone
•
Recent Close– A Recent Closing transmission is sent if an alarm occurs within 2 minutes of the
expiration of the Exit Time. The user number is included in the Recent Closing transmission when
available.
Once you have entered these report codes, the system prompts you with the Quit menu.
QUIT REPORT MENU
1 = YES 0 = NO
0
If you have completely finished entering report codes, press [1] (Y) to quit Report Code Programming. If you
wish to enter other system report codes, enter 0 (N).
Press [✱] to continue.
– 28 –
System Group #3 Codes
PROMPT
EXPLANATION
SYSTEM GROUP #3 ?
1 = YES 0 = NO 0
To enter System Group #3 codes, press [1] (Y).
EARLY OPEN
1st 00 2nd 00
Enter the first digit of the Early Opening Report Code. Press [✱]. Enter the second digit of the report code.
If the user number is desired as the second digit, enter 01 (not necessary for Contact ID or High Speed
formats).
Press [✱] to continue.
Enter the rest of the codes in the same manner. Other codes in System Group #3 are:
•
Early Close
•
Late Open
•
Late Close
•
Failed to Open
•
Failed to Close
•
Auto-Arm Failed
•
Schedule Change
Once you have entered these report codes, the system prompts you with the Quit menu.
QUIT REPORT MENU
1 = YES 0 = NO
0
If you have completely finished entering report codes, press [1] (Y) to quit Report Code Programming. If you
wish to enter other system report codes, enter 0 (N)
Press [✱] to continue.
System Group #4 Codes
PROMPT
EXPLANATION
SYSTEM GROUP #4 ?
1 = YES 0 = NO 0
To enter System Group #4 codes, press [1] (YES).
WALK TEST START
1st 00 2nd 00
Enter the first digit of the Fire Walk Test Start Report Code. Press [✱]. Enter the second digit of the report
code.
Press [✱] to continue.
Enter the rest of the codes in the same manner. Other codes in System Group #4 are:
•
Fire Walk-Test End.
•
Off-Normal.
Once you have entered these report codes, the system prompts you with the Quit menu.
QUIT MENU MODE?
1 = YES 0 = NO 0
Enter 1 to exit back to normal Programming mode. Enter 0 to stay in Menu mode.
– 29 –
Alpha Descriptors Programming
You can program a user-friendly English language description/location for all protection zones, relays, keypad panics, polling
loop short, and RF receiver supervision troubles.
Each description can be composed of a combination of words (up to 3) that are selected from a vocabulary of 244 words
stored in memory, and any word can have an "s" or " 's " added to it.
NOTE: Due to the use of 3-digit zone numbers, the first word of the descriptor is limited to 6 characters if you want it to fit on
the top line of the display.
In addition, up to 60 installer-defined words can be added to those already in memory. Thus, when an alarm or trouble occurs
in a zone, an appropriate description for the location of that zone will be displayed at the keypad.
A custom installer's message can be programmed for each partition which is displayed when the system is "Ready" (e.g., THE
PETERSONS’).
1. To program alpha descriptors, enter Programming mode, then press #93 to display "ZONE PROG?"
2. Press [0] (NO) twice to display "ALPHA PROG?".
3. Press [1] to enter Alpha Programming.
There are 6 submenu selections that will be displayed one at a time.
Press [1] to select the mode desired.
Press [0] to display the next mode available. The alpha menu selections are:
4.
ZONE DESCRIP?
For entering zone descriptors.
DEFAULT SCREEN?
For creating custom message; displayed when system is ready.
CUSTOM WORD?
For creating custom words for use in descriptors.
PART DESCRIP?
For creating 4-character partition names.
EXIT EDIT MODE?
Press [1] to exit back to #93 Menu Mode.
Refer to the sections that follow for procedures for adding alpha descriptors.
Zone Descriptors
1. Select ZONE DESCRIPTOR mode.
The keypad keys perform the following functions:
[3] Scrolls both alphabet and actual words in ascending alphabetical order.
[1] Scrolls both alphabet and actual words in descending alphabetical order.
[2] Adds or removes an "s" or " 's " to a vocabulary word.
[6] Switches between alphabet and actual word list; used to accept entries.
[8] Saves the zone description in the system's memory.
[#] [#] plus zone number displays the description for that zone.
2. Enter the zone number to which you want to assign a descriptor.
For example, key [✱] 001 to begin entering the description for Zone 1, (key [✱] 002 for Zone 2, [✱] 003 for Zone 3, etc.).
The following is displayed: ✱ ZN 001 A.
Note that the first letter of the alphabet appears after the zone number, and that the zone number is automatically
included with the description.
3. Enter the descriptor for that zone.
Use one of two methods as follows:
(Assume, for example, that the desired description for Zone 1 is BACK DOOR.)
a) Press [#] followed by the 3-digit number of the first word from the fixed dictionary shown later in this section (e.g.,
[0][1][5] for BACK).
Press [6] in order to accept the word and proceed, or press [8] to store the complete descriptor and exit;
or
b) Select the first letter of the desired description (note that "A" is already displayed). Use the [3] key to advance
through the alphabet and the [1] key to go backward.
Press [3] key repeatedly until "B" appears (press [1] to go backwards if you happen to pass it), then press [6] to
display the first available word beginning with “B”.
Press [3] repeatedly to advance through the available words until the word “BACK” is displayed.
To add an "s" or "'s," if you need to, press 2. The first depression adds an "s," the second depression adds
an " 's, " the third depression displays no character (to erase the character), the fourth depression adds an
"s," etc.
– 30 –
4.
5.
6.
7.
Accept the word.
To accept the word, press [6], which switches back to the alphabet list for the next word, or press [8] to store the
complete descriptor and then exit.
Select the next word.
For selection of the next word (DOOR), repeat step 3a (word #063) or 3b, but selecting the word "DOOR.”
To accept the word, press [6], which again switches back to alphabet list.
Store the descriptor.
When all desired words have been entered, press [8] to store the description in memory.
To review the zone descriptors, key [#] plus zone number (e.g., #001).
To edit zone descriptors, key [✱] plus zone number (e.g., ✱001)
Exit Zone Description Mode: enter 000.
Default Screen (Custom Message Display)
Normally, when the system is in the disarmed state, the following display is present on the keypad.
****DISARMED****
READY TO ARM
Part or the entire above message can be modified to create a custom installer message for each partition. For example,
“****DISARMED****” on the first line or “READY TO ARM” on the second line could be replaced by the installation company
name or phone number for service.
NOTE: There are only 16 character spaces on each of the two lines.
To create a custom display message, proceed as follows:
1. Select Default Screen mode.
The keypad asks for the partition number for this message.
Enter the partition number. Press [✱] to accept entry.
The following display appears:
****DISARMED****
READY TO ARM
2.
3.
4.
A cursor is present at the extreme left of the first line (over the first "star"). Press [6] to move the cursor to the right and [4]
to move the cursor to the left. Press [7] to insert spaces or erase existing characters.
Create the message.
For example, to replace “READY TO ARM” with the message “SERVICE 424-0177,” proceed as follows:
Press [6] to move the cursor to the right, and continue until the cursor is positioned over the first location on the second
line.
Press [3] to advance through the alphabet to the first desired character (in this case, "S"). Press [1] to go backward, when
necessary. When the desired character is reached, press [6].
The cursor then moves to the next position, ready for entry of the next character (in this example, "E"). When the cursor
reaches a position over an existing character, press [3] or [1] to advance or back up from that character in the alphabet.
Proceed in this manner until all characters in the message have been entered.
Save the message.
Store the new display message in memory by pressing [8].
The system asks for a new partition number.
Enter 0 to quit or 1-8 for a new partition number.
Custom Words
Up to 60 installer-defined words can be added to the built-in vocabulary. Each of the 60 "words" can actually consist of several
words, but bear in mind that a maximum of 10 characters can be used for each word string.
1. Select CUSTOM WORD Mode.
The keys perform the following functions:
[3] Advances through alphabet in ascending order.
[1] Advances through alphabet in descending order.
[6] Selects desired letter; moves the cursor 1 space to the right.
[4] Moves the cursor one space to the left.
[7] Inserts a space at the cursor location, erasing any character at that location.
[8] Saves the new word in the system's memory.
[✱] Returns to Description Entry Mode.
2. Enter the custom word number (01-60) you want to create.
For example, if you are creating the first word (or word string), enter 01; when creating the second word, enter 02, and so
on. A cursor now appears at the beginning of the second line.
– 31 –
3.
4.
5.
6.
7.
Type the word using one of two methods as follows:
a) Press [#], followed by the 2-digit entry for the first letter you would like to display (e.g., 65 for "A").
When the desired character appears, press [6] to select it. The cursor will then move to the right, in position for the
next character. Press [#] plus the 2-digit entry for the next letter of the word.
or
b) Press 3 to advance through the list of symbols, numbers, and letters.
Press 1 to move back through the list.
When you have reached the desired character, press [6] to select it. The cursor then moves to the right, in position
for the next character.
Repeat step 3 to create the desired custom word (or words).
Press [4] to move the cursor to the left if necessary.
Press [7] to enter a blank (or to erase an existing character).
Each word or word string cannot exceed 10 characters.
Save the word by pressing [8].
This returns you to the “CUSTOM WORD?” display. The custom word (or string of words) is automatically added to the
built-in vocabulary at the end of the group of words beginning with the same letter.
Custom words are retrieved as word numbers 255 to 314 for words 1 to 60, respectively, when using method 3a to enter
alpha descriptors.
When using method 3b to enter alpha descriptors, each word appears at the end of the group of words that begin with the
same letter as it does.
Repeat steps 2 through 6 to create up to a maximum of 60 custom words (or word strings).
Exit Custom Word Mode by entering 00 at the “CUSTOM WORD” prompt.
Partition Descriptors
1. Select "Part DESCRIPT." Mode.
The system asks for the partition number desired. Enter the number as a single-key entry 1-8.
2. Follow the same procedure as for custom words.
NOTE: The partition descriptors are limited to 4 characters (e.g., WHSE for warehouse).
– 32 –
Alpha Descriptor Vocabulary
(For entering alpha descriptors. To select a word, press [#] followed by the word's 3-digit number.)
NOTE: This vocabulary is not to be used for relay voice descriptors. See the Relay Voice Descriptors section when
programming relay voice descriptors.
000 (Word Space)
• 001 AIR
• 002 ALARM
004 ALLEY
005 AMBUSH
006 ANTENNA
• 007 AREA
• 008 APARTMENT
009 ART
• 010 ATTIC
011 AUDIO
012 AUX
013 AUXILIARY
• 015 BACK
• 016 BAR
017 BARN
• 018 BASEMENT
• 019 BATHROOM
• 021 BEDROOM
022 BELL
023 BELL 1
024 BELL 2
• 025 BLOWER
• 026 BOILER
027 BOTTOM
028 BOX
029 BREAK
• 030 BUILDING
031 BURNER
•
•
•
•
032
034
036
037
038
039
040
041
042
043
044
045
046
047
048
049
050
051
033
053
• 054
055
• 056
057
CABINET
CAMERA
CASE
CASH
CCTV
CEILING
CELLULAR
CENTRAL
CIRCUIT
CLIP
CLOSED
COIN
COLD
COATROOM
COLLECTION
COMBUSTION
COMPUTER
CONTACT
CORRIDOR
058
• 059
061
062
• 063
• 065
• 066
067
• 068
069
• 070
DIALER 2
DINING
DISPLAY
DOCK
DOOR
DOWN
DOWNSTAIRS
DRAWER
DRIVEWAY
DRUG
DUCT
• 071
072
073
035
074
075
• 076
077
• 078
079
EARTH
EAST
ELECTRIC
ELEVATOR
EMERGENCY
ENTRY
EQUIPMENT
EXECUTIVE
EXIT
EXTERIOR
• 080
081
082
• 084
085
• 086
• 087
088
• 090
091
• 092
094
FACTORY
FAILURE
FAMILY
FENCE
FILE
FIRE
FLOOR
FLOW
FOYER
FREEZER
FRONT
FURNACE
095
• 096
• 097
098
• 099
100
101
102
GALLERY
GARAGE
GAS
GATE
GLASS
GROUND
GUEST
GUN
112 JEWELRY
• 113 KITCHEN
• 114 LAUNDRY
• 115 LEFT
116 LEVEL
• 117 LIBRARY
• 118 LIGHT
119 LINE
120 LIQUOR
• 121 LIVING
• 122 LOADING
064 LOBBY
• 083 LOCAL
123 LOCK
124 LOOP
125 LORRA
126 LOW
• 127 LOWER
• 128
131
089
• 132
• 134
135
• 020
093
129
137
138
• 140
141
108
• 109
110
111
164
• 165
166
167
168
130
169
133
136
003
170
• 171
• 172
173
•
•
•
•
•
•
•
• 143 NORTH
144 NURSERY
• 103 HALL
• 104 HEAT
105 HIGH
106 HOLDUP
• 139 HOOD
• 052 HORN_CKT
107 HOUSE
060 HVAC
DELAYED
DEN
DESK
DETECTOR
DIALER 1
MACHINE
MAIN
MAN_PULL
MASTER
MEDICAL
MEDICINE
MEN
MIDDLE
MODULE
MONEY
MONITOR
MOTION
MOTOR
163 QUAD
INFRARED
INSIDE
INTERIOR
INTRUSION
• 145
146
• 147
148
• 149
150
151
OFFICE
OIL
OPEN
OPENING
OUTSIDE
OVERFLOW
OVERHEAD
• 153
152
154
• 155
156
• 157
158
159
160
161
• 162
PANIC
PARKING
PASSIVE
PATIO
PERIMETER
PHONE
PHOTO
POINT
POLICE
POOL
POWER
•
•
174
175
142
176
177
178
187
179
180
181
182
183
184
185
186
188
189
190
191
192
194
195
196
198
193
199
200
201
203
197
204
205
206
207
208
• 209
210
COMMUNICATOR
REAR
RECREATION
REFRIG
REFRIGERATION
RELAY
RELAY 1
REMOTE
RESTAURANT
RESTROOM
RF
RIGHT
ROOM
ROOF
SAFE
SCREEN
SECURITY
SENSOR
SERVICE
SHED
SHIPPING
SHOCK
SHOP
SHORT
SHOW
SIDE
SKYLIGHT
SLIDING
SMOKE
SOUNDER
SOUTH
SPRINKLER
STAIRWAY
STATION
STORE
STORAGE
STORY
STRIKE
STROBE
SUMP
SUPERVISED
SUPERVISION
SWITCH
SYSTEM
TAMPER
TAPE
TELCO
TELEPHONE
TELLER
TEMPERATURE
THERMOSTAT
• 211
212
213
214
•
•
•
•
•
•
•
•
TOOL
TRANSMITTER
TRAP
TRIGGERS
202
216
217
218
219
220
221
222
223
UNIT
UP
UPPER
UPSTAIRS
UTILITY
VALVE
VAULT
VIBRATION
VOLTAGE
224
225
226
215
227
228
229
230
014
231
WALL
WAREHOUSE
WASH
WATERFLOW
WEST
WINDOW
WINE
WING
WOMEN
WORK
232 XMITTER
233 YARD
234 ZN-1
• 235 ZONE
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
0
1
1ST
2
2ND
3
3RD
4
4TH
5
5TH
6
6TH
7
7TH
8
8TH
9
9TH
Custom Word 1
to
314 Custom Word 60
CHARACTER (ASCII) CHART
32
33
34
35
36
37
38
39
40
41
(space)
!
"
#
$
%
&
'
(
)
42
43
44
45
46
47
48
49
50
51
*
+
,
.
/
0
1
2
3
52
53
54
55
56
57
58
59
60
61
(For Adding Custom Words)
4
62
>
5
63
?
6
64
@
7
65
A
8
66
B
9
67
C
:
68
D
;
69
E
<
70
F
=
71
G
NOTE: This factory-provided vocabulary of words is subject to change.
– 33 –
72
73
74
75
76
77
78
79
80
81
H
I
J
K
L
M
N
O
P
Q
82
83
84
85
86
87
88
89
90
R
S
T
U
V
W
X
Y
Z
Device Programming
This menu is used to program keypads, receivers, and relay modules, etc.
Device Address 00 is always set as an alpha keypad assigned to Partition 1 with no sounder suppression
options, and these settings cannot be changed.
From Data Field Programming mode, press #93 to display "ZONE PROG?" Press [0] repeatedly to display "DEVICE PROG?"
PROMPT
EXPLANATION
DEVICE PROG?
1=YES 0=NO
Press [1] to enter Device Programming.
DEVICE ADDRESS
01-30, 00=QUIT
0
01
The device address identifies the device to the control. Enter the 2-digit device address number to match
the device's physical address setting (01-30).
Press [✱] to accept entry.
Select the type of addressable device as follows:
DEVICE TYPE
00
00 = device not used
01 = alpha keypad (6160/6160CR-2)
03 = RF receiver (5881ENHC, 5883H)
04 = output relay module (4204)
05 = Do Not Use
06 = communicator
09 = Do Not Use
10 = Do Not Use
12 = RIS (Remote Interactive Services)
Press [✱] to accept entry.
Alpha Keypad
PROMPT
EXPLANATION
01 CONSOLE PART.
If you selected device type 01 (alpha keypad), this prompt appears. Enter the addressable device's default
partition number (1 to maximum number of partitions programmed for system in field 2*00). This is the
primary partition for the device. Enter 9 to make this keypad a "Master" keypad for the system.
Press [✱] to accept entry.
1
01 SOUND OPTION
00
01 KEYPAD GLBL?
0
01 AUI ?
1 = YES 0 = NO
If you entered device type 01 (alpha keypad), this prompt appears. Keypads can be individually
programmed to suppress arm/disarm beeps, entry/exit beeps and chime mode beeps. This helps prevent
unwanted sounds from disturbing users in other areas of the premises.
Enter a number 0-3 for the keypad sounding suppression options desired for the keypad as follows:
0 = no suppression
1 = suppress arm/disarm & entry/exit beeps
2 = suppress chime mode beeps only
3 = suppress arm/disarm, entry/exit and chime mode beeps
Press [✱] to accept entry.
If you entered device type 01 (alpha keypad), this prompt appears. Each keypad can give users with access
to multiple partitions the ability to arm and disarm those partitions from it. To enable this keypad for global
arming/disarming, enter 1. To prevent the ability to use this keypad for global arming/disarming, enter 0.
Press [✱] to accept entry.
Do Not Use. Must be set to “0”.
0
Press [✱] to accept entry.
– 34 –
RF Expander
PROMPT
EXPLANATION
01 RF EXPANDER
HOUSE ID
00
If you selected device type 03 (RF receiver), this prompt appears. Enter the 2-digit House ID (00-31).
Press [✱] to accept entry.
Output Relay Module
PROMPT
EXPLANATION
01 SUPERVISED CF?
If you selected device type 04 (relay module), this prompt appears. Enter 1 if the unit is a 4204CF. If not,
enter 0. If you enter 1, only Relay 1 (Output A) and Relay 3 (Output B) on each module may be programmed
for functions.
NOTE: For Commercial Fire installations, only one notification appliance module may be used, and only one
notification appliance output (A or B) may be used on that module.
Press [✱] to accept entry.
0
Communicator
If you selected device type 6, the 6160/6160CR-2 Keypad functions similarly to the Programming Tool. See Figure 1 for the
functions of the keys on the 6160CR-2.
(A)
BS/ESC
1
READY
SHIFT
FUNCTION
WHEN LIT
POWER
ALARM
SILENCED
2
(B)
/
4
MAX
5
(C)
N/Y
7
8
READY
6 BYPASS
CODE
X
9
CHIME
0
#
6160CR2-001-V1
SHIFT
TEST
STAY
F
ENTER
SPACE
(D)
3
T
S
INSTANT
AWAY
E
D
SUPV
TROUBLE
OFF
C
B
A
ARMED
Figure 1: 6160CR-2 Key Functions for Programming the Communicator
Each key has two possible functions: a normal function and a SHIFT function. To perform a normal key function, simply press
the desired key. To perform a SHIFT key function, press SHIFT key, then press desired function key.
Normal and SHIFT key Functions:
Key
Normal Key Function
SHIFT Key Function
BS/ESC
[BS]: Press to delete entry
[ESC]: Press to quit Program Mode
Also, can reset EEPROM defaults *
↓/↑
[↓]: Scroll down programming
[↑]: Scroll up programming
N/Y
[N]: Press for "NO" answer
[Y]: Press SHIFT-Y for "YES" answer
SHIF
Press before pressing a SHIFT key function. Will light READY LED. LED goes out once a key is
T
pressed. Press again for each SHIFT function desired.
1/A
[1]: For entering the number 1
[A]: Used for entering C.S. ID number
2/B
[2]: For entering the number 2
[B]: Used for entering C.S. ID number
3/C
[3]: For entering the number 3
[C]: Used for entering C.S. ID number
4/D
[4]: For entering the number 4
[D]: Used for entering C.S. ID number
5/E
[5]: For entering the number 5
[E]: Used for entering C.S. ID number
6/F
[6]: For entering the number 6
[F]: Used for entering C.S. ID number
7/S
[7]: For entering the number 7
[S]: Not used
8/T
[8]: For entering the number 8
[T]: Not used
9/X
[9]: For entering the number 9
[X]: No SHIFT function
*/SPACE
[*]: Not used with 7845i-ent
[SPACE]: Not used
0
[0]: For entering the number 0
No SHIFT function
#/ENTER
[#/ENTER]: Press to accept entries
No SHIFT function
* Active only when the "REVIEW?" prompt is displayed.
– 35 –
The 6160/6160CR-2 Keypad displays the following prompts, which are sent by the Communicator to the control.
NOTE: These prompts are for the 7845i-ent Communicator only. If you are using a different communicator, refer to
the communicator’s instructions for the correct prompts.
PROMPT
EXPLANATION
DEVICE ADDRESS
Enter the device address of the Communicator. The default address is 3.
ID #
Enter the 4-digit customer account number, 0001-9999. This ID number will appear in the messages
generated by the Communicator. Messages generated by the panel and transmitted by the Communicator
will contain the ID number programmed into the panel. The Communicator and the panel should have the
same ID number, if possible.
(1234)
If a different 4-digit customer account number is used in the Communicator that is programmed into the alarm
control, the Communicator will transmit Communicator-specific messages (power-on reset, AC fail, etc.) using the
Communicator customer number, and alarm messages using the control panel’s customer number. If these
numbers are different, you will be billed for two AlarmNet Communicator accounts.
PROMPT
EXPLANATION
En.AlarmNetI Y/N
Press [Y] to enable alarm delivery via the Internet to an AlarmNet central station.
Press [N] to disable AlarmNet-i functionality.
AES Encrypt. Y/N
Press [Y] to use the AES Encryption method.
Press [N] to use the Blowfish Encryption.
(N)
Using the keypad, enter Port (443).
Web Port
(433)
Use Mstr Act [Y/N]
(N)
Press [Y] to use the account information assigned for Remote Access.
Press [N] to use AlarmNet-i specific account information.
Primary City ID
Enter the 2-digit primary city code, 01-99 (decimal).
Primary CS ID
Enter the primary central station's system ID number, 01-FE.
Primary Sub ID
Enter the 4-digit customer account number, 0001-9999.
En. 2nd CS Y/N
Press [Y] if redundant reporting to a second central station is desired.
Press [N] if not desired.
2nd City ID
Enter the 2-digit secondary city code, 01-99 (decimal).
2nd CS ID
Enter the secondary central station's system ID number, 01-FE.
2nd Sub ID
Enter the secondary 4-digit customer account number, 0001-9999.
Enable DW Y/N
(N)
Press [Y] to enable Direct Wire Downloading over IP.
Press [N] to disable Direct Wire Downloading over IP.
– 36 –
PROMPT
EXPLANATION
Supervision
(24 Hour)
Choices: 24 hours, 1 hour, US UL Line 6 min, CN UL Line Lvl 3 (3 min.), US UL Line 90 (seconds), CN UL
Line Lvl 4 (90 seconds), CN UL Line Lvl 5 (75 seconds), None.
NOTE: For Commercial Fire installations must be set to 90 seconds.
The 7845i-ent sends a supervision message once during the supervision period. AlarmNet transmits a
communications failure alarm to the central station if the supervision message is not received within the
period.
To scroll through the available choices:
•
Press the [space] key to scroll forward through the list of choices.
•
Press the [backspace] key to scroll back through the list if the desired entry has scrolled past.
Press the [Enter] key to select the time displayed.
Old Alarm Time
(10 Minutes)
The old alarm time sets how long an undeliverable alarm is retried for delivery to AlarmNet. If the message
is not validated, it is retried until the old alarm time is reached or the message is validated. The choices
available are: 10 Min., 15 Min., 30 Min., 1Hr, 2Hr, 4Hr, 8Hr, 12Hr and 24Hr. To scroll through the available
choices:
•
Press the [space] key to scroll forward through the list of choices.
•
Press the [backspace] key to scroll back through the list if the desired entry has scrolled past.
Press the [Enter] key to select the time displayed.
Fault Time (mins)
(05)
Enter the time delay (01-99 minutes) before the 7845i-ent notifies the control panel that there is loss of
contact with the network, or enter “00” if you do not want the 7845i-ent to alert the control panel of loss of
contact with the network. The 7845i-ent will alert the control panel of the loss of contact via a dedicated
status message. Refer to Table 3-5 in this Section for more information regarding the ECP Status Codes.
– 37 –
Output Programming
The system supports up to 96 outputs. Outputs can be used to perform many different functions and actions. Each output
must be programmed to begin one of four types of ACTIONS at a designated START event, and end that ACTION at a
designated STOP event. The options used to start and stop these devices are described below, followed by the actual screen
prompts and available entries.
NOTE: If you are using outputs on the polling loop (e.g., 4101SN) no more than 20 of the polling loop outputs may be
programmed for the same START or STOP condition. Also, if you are using ZONE # for the START of a polling loop
output and want that output to stop when the same zone restores, the STOP programming MUST BE BLANK.
If you are using Zone Type 17 (Waterflow) or 18 (Fire Supervisory) to trigger an output, you must program an Event
for the START (alarm, trouble, etc.). All other Zone Type/System Operations do not require an Event.
The letter(s) in parentheses after each function described below, such as (A) after ACTION, are those that appear in the
various summary displays of programmed data during programming.
ACTION (A)
START (STT)
STOP (STP):
The "ACTION" of the device is how the device will respond when it is activated by the "START"
programming. You may want the device to activate momentarily, to pulse on and off continuously, or to
remain activated until some other event occurs to stop it. There are five different action choices:
•
ACTIVATE for 2 SECONDS and then reset. If selected, it is not necessary to program a stop
parameter.
•
ACTIVATE and REMAIN ACTIVATED until stopped by some other event.
•
PULSE ON and OFF until stopped by some other event.
•
NO RESPONSE when the device is not used.
•
TOGGLE on and off alternately with each activation of event. Do not program a stop parameter as
this may cause unpredictable results.
The "START" programming determines when and under what conditions the device is activated. The
following START options are available:
1) EVENT (EV) is the condition (alarm, fault, trouble) that must occur to a zone or group of zones (zone
list) in order to activate the device. These conditions apply only when a zone list is used. The different
choices for "EVENT" are listed below and in “Programming Relays” later in this section.
•
ALARM
Action begins upon any alarm in an assigned zone in the zone list.
•
FAULT
Action begins upon any opening of an assigned zone in the zone list.
•
TROUBLE
Action begins upon any trouble condition in an assigned zone in the zone list.
•
NOT USED
Action is not dependent upon one of the above events.
ZONE LIST (ZL) is a group of zones to which the “EVENT” applies in order to activate a particular
device. Note that there are a total of 15 zone lists that can be programmed; when the selected EVENT
(alarm, fault or trouble) occurs in any zone in the selected “Start” ZONE LIST (01-15), activation of the
selected device will START.
2) ZONE # A specific zone going into alarm, fault, trouble, or restore (Event programming) can be used to
start the relay action. Enter the 3-digit zone number (000-128).
3) ZONE TYPE/SYSTEM OPERATION (ZT). If all zones to be used to start the device have the same
response type, and there are no other zones of this type that are not to activate this device, then
“ZONE TYPE” may be used instead of a "ZONE LIST" and "EVENT” to activate the device.
If a system operation, such as “DISARMING” or “ANY FIRE ALARM,” is to activate the device, enter
the appropriate choice under the “ZONE TYPE” option.
The “ZONE TYPE/SYSTEM OPERATION” option functions independently of the “EVENT/ZONE
LIST” combination.
If a specific "ZONE TYPE" is chosen, any zone of that response type going into alarm, trouble, or fault
will cause the device to activate as selected in "ACTION.” If the same “ZONE TYPE” is also chosen for
the STOP programming, any zone of that type that restores will de-activate the device.
If a "SYSTEM OPERATION" is chosen, that operation will cause the device to activate as selected in
"ACTION.” The different choices for "ZONE TYPE" and "SYSTEM OPERATION" are listed in
“Programming Relays” later in this section, and on the Programming Form.
4) PARTITION NO. (P). The device's "Start" ZONE TYPE/SYSTEM OPERATION may be limited to an
occurrence on one partition (1-8), or any partition (0).
The "STOP" programming determines when and under what conditions the device is de-activated. The
following options are available:
1). RESTORE ZONE LIST (ZL). If a "ZONE LIST" is used as the “Stop” event, the device de-activates
when all the zones in that list restore from a previous fault, trouble, or alarm condition. This occurs
regardless of what is programmed to "START" the device; therefore, a "RESTORE ZONE LIST" is
normally only used when a "ZONE LIST" is used to start the device.
– 38 –
2). ZONE TYPE/SYSTEM OPERATION (ZT). Instead of using a "RESTORE ZONE LIST," you can select
a specific zone (response) type or system operation action to de-activate the device.
If you choose a specific "ZONE TYPE," any zone of that response type that restores from a previous
alarm, trouble, or fault condition will cause the device to de-activate.
If you choose a "SYSTEM OPERATION," that operation causes the device to de-activate. The
different choices for "ZONE TYPE" and "SYSTEM OPERATION" are listed in “Programming Relays”
later in this section, and in the Programming Form.
3) PARTITION NO. (P). The device's "Stop" Zone Type/System Operation may be limited to an
occurrence on one partition (1-8), or on any partition (0).
The “ZONE TYPE/SYSTEM OPERATION” option functions independently of the
“RESTORE/ZONE LIST” combination.
Output Devices Programming
From Data Field Programming Mode, press #93 to display the "ZONE PROG?" prompt. Press [0] (NO) to each menu option
until the "OUTPUT PGM?" prompt appears. Press [1] (YES).
While in this mode, press [✱] to advance to next screen. Press [#] to back up to the previous screen.
PROMPT
EXPLANATION
ENTER RELAY #
(00=QUIT)
01
Enter the relay (output device) identification number 01-96. This is a reference number only, used for
identification purposes. The actual module address and relay number on the module are programmed in the
last two prompts.
Press [✱] to continue.
02 A EV ZL ZT P
STT 0 0 00 00 0
Press [✱] to continue.
02
STOP
The keypad displays a summary STOP screen.
Press [✱] to continue.
A ZL ZT P
0 00 00 0
02 RELAY ACTION
NO RESPONSE
0
The Relay Action is the way in which the relay will respond when activated by the "start" event. Enter the
desired action for this relay as follows:
0=not used; 1=close for 2 secs.; 2=stay closed; 3=pulse on/off; 4= toggle on and off alternately
NOTE: For options 1 and 4, do not program a “Stop” parameter.
02 START EVENT
NOT USED
0
02 START: ZN LIST
00
02 START: ZONE #
000
02 START: ZN TYPE
NO RESPONSE
00
An output may be activated by an Event/Zone List combination, and/or by a Zone Type/System Operation.
For an Event/Zone List combination, enter the event code as follows:
0=not used; 1=alarm; 2=fault; 3=trouble
NOTE: An Event is required for Zone List, Zone Number and Zone Types 17 and 18.
If you are not using a Zone List to activate the relay, enter 0.
Press [✱] to continue.
A zone list is a set of zones that can be used to initiate the start or stop relay action. If a zone list is being
used to start this relay action, enter the zone list number, 1-15. If a zone list is not being used, enter 0.
Press [✱] to continue.
A specific zone can be used instead of or in addition to an Event/Zone List or Zone Type/System Operation
combination to start the relay action. Enter the 3-digit zone number.
Press [✱] to continue.
A Zone Type/System Operation can be used instead of or in addition to an Event/Zone List combination or
a specific zone to start the relay action. If a Zone Type/System Operation is being used, enter the 2-digit
code as listed in the table that follows.
Press [✱] to continue.
– 39 –
Choices for Start/Stop Zone Types and System Operations:
00 = No Response (Not Used)
22 = Disarming (Code + Off)
01 = Entry/Exit #1
23 = No Alarm Response
27 = Access Point (allows more than one
02 = Entry/exit #2
03 = Perimeter
relay to be controlled by activation if access
04 = Interior Follower
point request) - Not Used
05 = Trouble Day/Alarm Night
28 = MLB Supervision - Not Used
06 = 24-Hr. Silent
29 = Momentary Exit - Not Used
07 = 24-Hr. Audible
30 = On Second Code + Off
08 = 24-Hr. Auxiliary (Not for Medical Use) 31 = End of Exit Time
09 = Fire Alarm or Trouble
32 = Start of Entry Time
10 = Interior W/Delay
33 = Any Burglary Alarm
12 = PLM Supervision - Not Used
34 = Code + [#] + 71 K0ey Entry
13 = Remote P/S
35 = Code + [#] + 72 Key Entry
14 = CO Detector Alarm
36 = At Bell 1 Timeout **
16 = Fire With Verification
37 = 2x Bell 1 Timeout **
17 = Waterflow*****
38 = Chime
18 = Fire Supervisory
39 = Fire Alarm
19 = 24-Hour Trouble
40 = Bypassing
20 = Arming-STAY***
41 = AC Power Fail
21 = Arming-AWAY****
42 = System Battery Low
*
Stop condition only
** Or at disarming, whichever occurs earlier
*** The output also activates when the partition is armed in the INSTANT mode
**** The output also activates when the partition is armed in the MAXIMUM mode
***** Use an event of fault or alarm as the START option
43 = Communication failure
44 = RF Low Battery
45 = Polling Loop Failure
47 = Console Failure
51 = RF Receiver Failure
52 = Kissoff
54 = Smoke Detector Reset
55 = Disarm + 1 Minute
56 = XX Minutes (enter XX in field 1*74) *
57 = YY Seconds (enter YY in field 1*75) *
58 = Duress
60 = Audio Alarm Verification (must be
selected for both START and STOP
operation)
61 = Code + [#] + 67
62 = Bell 2 Timeout
63 = Auxiliary Relay Timeout
If you are using options 56 and/or 57 (usually as the STOP Zone Type), you must program data fields 1*74
and 1*75 for the respective relay timeouts for minutes and seconds.
Do not use a zone programmed with an RF Button (Input Type BR) to STOP a relay. The system will not deactivate the relay.
PROMPT
EXPLANATION
02 STOP: ZN LIST
If a zone list is being used to stop this relay action, enter the zone list number, 1-15. The restore of a zone
on the zone list stops the relay. If a zone list is not being used, enter 0.
Press [✱] to continue.
00
02 STOP: ZN TYPE
NO RESPONSE
00
If a Zone Type/System Operation is being used to stop the relay action, enter the 2-digit code listed in the
Choices for Start/Stop System Operation chart.
NOTE: If a 4204CF is being used, the stop action for a NAC must be programmed as zone type 62, Bell 2
Timeout. Only one relay of the 4204CF may be used for this function.
Press [✱] to continue.
02 STOP: PARTN
ANY PARTITION
This is the partition to which the stop condition will be limited. Enter 0 for any partition. Enter 1-8 for specific
partition number.
Press [✱] to continue.
0
02 RELAY GROUP
00
Relays may be grouped for common activation by time-driven events (commands 06-10). Enter 00 (no
group) or 01-15 for a specific group number.
Press [✱] to continue.
Enter 1 only if this output is to be used to activate a fire alarm sounder.
02 FIRE BELL
1=YES 0=NO
0
02 RESTRICTION
1=YES 0=NO
0
Press [✱] to continue.
The system may have some devices that are not intended to be under end user control, such as relays
activating fire doors or machinery.
NOTE: #70 must be set to yes for Commercial Fire installations.
Enter 1 if the end user will be restricted from accessing this relay group.
Press [✱] to continue.
– 40 –
PROMPT
EXPLANATION
02 RELAY TYPE
V-PLEX
Enter 0 for V-Plex (polling loop) devices. Enter 1 for (ECP) relay modules (4204/4204CF).
Press [✱] to continue.
0
02 V-PLEX ZONE #
000
For polling loop trigger outputs (4101SN), enter the protection zone number (001-128) linked to each output,
if used. Be sure to enroll the module’s serial number (see Zone Programming).
Press [✱] to continue.
02 ECP ADDRESS
If you selected 1 or 3 for (4204/4204CF), enter the actual module's address (01-15 – 4204/4204CF) as set
by its DIP switches. Up to 8 4204/4204CF modules can be installed in a system.
Press [✱] to continue.
00
02 MODULE RELAY#
0
For 4204 Relay Outputs, enter the specific relay number on that module (1-4). For 4204CF outputs, enter
only module relay number 1 (Output A) or relay number 3 (Output B). These are the only two
programmable relays on the 4204CF Module.
Press [✱] to continue.
The keypad will display the Start and Stop summary screens again.
Press [✱] to continue.
When all relays have been programmed, enter 00 at the "ENTER RELAY NO." prompt.
If you are defining a zone list, continue to the next section. If not, enter 00 + [✱] at the next two prompts. You will then be
asked "Quit Menu Mode?" Enter 1 for "Yes," 0 for "No." Then enter ✱99 to exit programming completely.
If supervision of the 4204CF Relay Output is desired, enter a response type for that output's corresponding supervisory zone.
This is equal to 600 + [Relay ID No.]. For example, if you are programming Relay ID No. 1, the relay's supervisory zone 601.
Program this zone with response type 05 (Day/Night) in Zone Programming.
Zone List Programming
After all relays have been programmed, upon entering 00 at the "ENTER RELAY NO." prompt, you are asked to enter a zone
list. If a zone list number was used to start or stop a relay, you must define the zones belonging to that list as follows:
PROMPT
ENTER Zn LIST ?
00=QUIT
01 ADD ZONE #
000=QUIT
01 Del Zn LIST ?
1=YES 0=NO
01 DEL ZONES ?
1=YES 0=NO
EXPLANATION
Enter the zone list number 01-15. Enter 00 to quit.
00
000
Using 3-digit entries enter each zone to be included in this zone list. Press [✱] after you enter each zone
number.
When you have entered all zones, enter 000.
Press [✱] to continue.
Enter 0 to save this zone list. Enter 1 to delete it.
0
0
Enter 1 to delete one or more zones in that zone list. Enter 0 if no changes are necessary. If you enter 1,
the following screen appears; otherwise, the "Enter Zone LIST" prompt reappears.
01 Zn to DELETE ?
000=QUIT
000
Enter each zone number to be deleted from the zone list, pressing [✱] after each number.
VIEW Zn LIST ?
00=QUIT
This display appears if you pressed 00 at the “Enter Zone LIST” prompt. Enter the zone list number that you
wish to view.
Press [✱] to continue.
00
01 ASSIGNED ZONE
000=QUIT
000
Press [✱] to scroll through all zones in that list. Enter 000 +[✱] to quit.
Press [1] to exit Menu Mode.
Press ✱99 to exit Program Mode.
– 41 –
Relay Voice Descriptors
Each voice descriptor can consist of up to 3 words selected from the Relay Voice Descriptors and Custom Word Substitutes
Vocabulary list (later in this section).
The index numbers from this vocabulary list are to be used for relay voice descriptors only. For normal
system voice annunciation (e.g., alarms, troubles, status), use the highlighted words in the alpha vocabulary
list in the Alpha Programming part of this guide.
To enter relay voice descriptors, do the following:
1. From Data Field Programming mode, press #93 to display the "ZONE PROG?" prompt.
2. Press [0] (NO) to each menu option until the "RLY VOICE DESCR?" prompt is displayed. Follow the instructions below.
While in this mode, press [✱] to advance to next screen. Press [#] to back up to previous screen.
PROMPT
EXPLANATION
RLY VOICE DESCR?
1=YES 0=NO
Press [1] to program voice descriptors for relays.
0
ENTER RELAY NO.
00=QUIT
01
Enter the 2-digit relay number (01-32) for the relay desired, or enter 00 to quit Relay Voice Descriptor
Programming Mode.
Press [✱]
01 ENTER DESC d1
From the Relay Voice Descriptors and Custom Word Substitutes Vocabulary list, enter the 3-digit index
number for the first word of the relay descriptor phrase.
Press [✱] to accept entry.
01 ENTER DESC d2
From the Relay Voice Descriptors and Custom Word Substitutes Vocabulary list, enter the 3-digit index
number for the second word of the relay descriptor phrase. If second word is not desired, press [000].
Press [✱] to accept entry.
01 ENTER DESC d3
From the Relay Voice Descriptors and Custom Word Substitutes Vocabulary list, enter the 3-digit index
number for the third word of the relay descriptor phrase. If third word is not desired, press [000].
Press [✱] to accept entry. The “ENTER RELAY NO.” prompt appears. Enter the next relay number to be
programmed. When you have programmed all output devices, enter 00 to quit.
Enter ✱99 to exit Program Mode.
– 42 –
Relay Voice Descriptors and Custom Word Substitutes Vocabulary
Word
Index
Air ............................ 116
Alarm ....................... 255
And .......................... 067
Apartment ................ 117
Appliances ............... 161
Area ......................... 118
Attic.......................... 119
Back......................... 121
Bar ........................... 122
Basement................. 021
Bathroom ................. 051
Battery ..................... 053
Bedroom .................. 015
Blower...................... 123
Boiler........................ 124
Bright ....................... 162
Building .................... 125
Burglary ................... 039
Central ..................... 089
Chime ...................... 054
Closed...................... 126
Computer ................. 127
Console.................... 066
Den .......................... 052
Detector ................... 128
Word
Index
Device ......................060
Dim ...........................163
Dining .......................031
Door..........................016
Down ........................008
Downstairs................184
Driveway...................130
Duct ..........................131
Word
Index
Gas .......................... 138
Glass........................ 139
Hall........................... 050
Heat ......................... 010
Inside ....................... 209
Kitchen ..................... 022
East ..........................132
Eight .........................077
Eighth .......................221
Equipment ................133
Exit ...........................004
Factory .....................134
Fence .......................135
Fifth ..........................218
Fire ...........................040
First .........................136
Five...........................074
Floor .........................029
Four ..........................073
Fourth .......................217
Foyer ........................137
Front .........................087
Garage .....................023
Word
Index
Off............................ 011
Office ....................... 147
On............................ 058
One.......................... 070
Open........................ 148
Outside .................... 210
Laundry .................... 140
Left ........................... 027
Library ...................... 141
Light ......................... 019
Living........................ 030
Loading .................... 142
Lower ....................... 094
Machine.................... 143
Master ...................... 144
Medical..................... 014
Motion ...................... 145
Nine.......................... 078
Ninth......................... 222
No ............................ 165
North ........................ 146
Not ........................... 012
– 43 –
Panic........................ 013
Partition.................... 090
Patio ........................ 149
Phone ...................... 061
Power ...................... 063
Pump ....................... 166
Rear ........................ 088
Right ........................ 028
Room ....................... 018
's .............................. 007
Second..................... 056
Service..................... 150
Seven ...................... 076
Seventh.................... 220
Shed ........................ 151
Shop ........................ 152
Side .........................153
Six............................075
Sixth.........................219
Word
Index
Smoke ..................... 024
South....................... 155
Stairs ....................... 006
Station ..................... 156
Storage.................... 157
Sun.......................... 154
System .................... 062
Temperature ............ 158
Third ........................ 159
Three ....................... 072
Tool ......................... 213
Two ......................... 071
Up............................ 025
Upper ...................... 187
Upstairs ................... 183
Utility ....................... 185
West ........................ 215
Window.................... 017
Wing ........................ 216
Zero......................... 069
Zone ........................ 002
Scheduled Check-in
The system can be programmed to call the downloader automatically, at a scheduled time. Once the connection is made, the
downloader can perform any and all functions (arm, disarm, upload, etc.). The downloader determines the functions it
performs.
To enter scheduled check-in, do the following:
1. From Data Field Programming mode, press #93 to display the "ZONE PROG?" prompt.
2. Press [0] (NO) to each menu option until the "SCHEDULED CHK-IN" prompt is displayed.
PROMPT
SCHEDULED CHK-IN
1=YES 0=NO
Chk-In Interval
None
EXPLANATION
Enter [1] at this prompt.
0
0
Enter the check-in interval.
0 = None; 1 = Weekly; 2 = Monthly; 3 = Quarterly; 4 = Yearly.
Press [✱] to accept entry.
DAY: M T W T F S S
1 2 3 4 5 6 7 1
If you selected 1 (weekly), the Day of the Week prompt is displayed. Enter the day of the week (1-7).
Press [✱] to accept entry and move to the Time of the Day prompt.
Quarter of Year
JAN, APR, JUL, OCT
If you selected 3 (quarterly), the Quarter of the Year prompt is displayed. Enter the quarter of the year. 0 =
January, April, July, and October; 1 = February, May, August, and November; 2 = March, June, September,
and December.
Press [✱] to accept entry and move to the Day of the Month prompt.
Month of Year
(01-12)
Day of Month
(01-28)
0
01
If you selected 4 (yearly), the Month of Year prompt is displayed. Enter the month (01-12).
Press [✱] to accept entry and move to the Day of the Month prompt.
01
If you selected 2 (monthly), the Day of the Month prompt. Enter the day of the month (01-28).
Press [✱] to accept entry and move to the Time of the Day prompt.
The Time of the Day prompt is displayed. Enter the time of day for the check-in. Enter the hour of the day
(01-12). Press [✱] to accept entry. The cursor moves to the minutes position. (Press the [#] to move the
cursor backwards.)
Enter the minutes of the hour (00-59). Press [✱] to accept entry.
The cursor moves to the AM/PM position. Press [✱] to accept the current selection or press any key (1-9)
except the [✱] or [#] to toggle the AM/PM selection.
NOTE: The programming of field 1*71 determines the time of day format (12- or 24-hour).
Time of Day
12:00AM
QUIT MENU MODE?
1 = YES 0 = NO
Enter 1 to exit back to normal programming mode. Enter 0 to stay in menu mode.
0
– 44 –
System Layout Worksheets
Before programming any security system, you should first define the installation. To help you lay out a partitioned
system, use the following worksheets. This will further simplify the programming process.
Partition #
Descriptor
(4-char max)
Prim.
Sub. #
PARTITIONS
Sec.
Sub. #
Alpha Default Message
(32-character maximum)
Partition 1
Partition 2
Partition 3
Partition 4
Partition 5
Partition 6
Partition 7
Partition 8
Keyswitch Arming Partition Assignment (1-8):
Wireless Keypad Partition Assignment (1-8):
Use Partition Descriptor (yes/no)?
Common Lobby Partition Assignment (1-8):
Option
COMMUNICATION OPTIONS BY PARTITION
Part. 1
Part. 2
Part. 3
Part. 4
Part. 5
Part. 6
Part. 7
Part. 8
Swinger Suppression Count 00-15; 00=no suppression
Cancel Report After Disarm
Dialer Reports for Panic (* + 1)
Dialer Reports for Panic (# + 3)
Dialer Reports for Panic (* + #)
Dialer Reports for Duress
Burglary Alarm Communications Delay (16 sec.)
SYSTEM DEFINITIONS BY PARTITION (enter values or yes/no)
Option
Part. 1
Part. 2
Part. 3
Part. 4
Part. 5
Part. 6
Part. 7
Part. 8
Entry Delay #1 (00, 30-225 seconds):
Exit Delay #1 (00, 45-225 seconds):
Entry Delay #2 (00, 30-225 seconds):
Exit Delay #2 (00, 45-225 seconds):
Quick Arming
Multiple Alarms per Arming
Console Panic for Zone 995 (* + 1)
Console Panic for Zone 996 (# + 3)
Console Panic for Zone 999 (* + #)
Allow Sign-on (GOTO function)
Non-Bypassable Zone (001-128)
Bell 1Sounder Duration (2 min. increments)
Bell 2 and Aux Relay Sounder Duration for (2 min. incr.)
Console Annunciation During Entry (3 beeps or continuous)
Console Annunciation During Exit
Bell 1Confirmation of Arming Ding
Bell 2 and Aux Relay 1Confirmation of Arming Ding
Chime on Bell 1
Chime on Bell 2 and Aux Relay
Access Control Relay (field 1*76)
Affects Lobby (check partitions that apply)
Arms Lobby (check partitions that apply)
Display Fire Alarms of Other Partitions
Display Burg and Panic Alarms of Other Partitions
Display Troubles of Other Partitions
– 45 –
PRINTER OPTIONS
Parallel or Serial printer
12- or 24-hour Time format
Printer On-Line (yes/no)
1200 or 300 baud Printer Baud Rate
Addr
Type
Part
Sound
Opt
00.
01.
02.
03.
04.
05.
06.
07.
08.
09.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
EVENT LOG TYPES
No
Option
Yes
Alarm
Trouble
Bypass
Open/Close
System
Test
DEVICES (keypads, 4204, rf receivers, communicator)
Supv
House
Kypd
Panel
CF?
ID
Glbal
ID
Device Types:
00 = Device Not Used
01 = Alpha Console
03 = RF Receiver
04 = Output Relay Module
05 = Not Used
06 = Communicator
09 = Not Used
10 = Not Used
Console Sounder Options:
0 = No Suppression
1 = Suppress Arm/Disarm and Entry/Exit Beeps
2 = Suppress Chime Mode Beeps Only
3 = Suppress Arm/Disarm, Entry/Exit and Chime
Mode Beeps
Defaults:
Addresses 00 =
Alpha Keypad; No Suppression
ACCESS CODES and USER DEFINITIONS FOR PARTITIONS 1 and 2
4-digit
Security
Code
Access
Group
0; 1-8
3-Digit
User #
Auth.
Level
Partition 1
Open/
Group
Close
Bypass
RF
Key
– 46 –
Global
Arm
3-Digit
User #
Auth.
Level
Partition 2
Open/
Group
Close
Bypass
RF
Key
Global
Arm
ACCESS CODES and USER DEFINITIONS FOR PARTITIONS 3 and 4
4-digit
Security
Code
Access
Group
0; 1-8
4-digit
Security
Code
Access
Group
0; 1-8
4-digit
Security
Code
Access
Group
0; 1-8
3-Digit
User #
Auth.
Level
Partition 3
Open/
Group
Close
Bypass
RF
Key
Global
Arm
3-Digit
User #
Auth.
Level
Partition 4
Open/
Group
Close
Bypass
RF
Key
Global
Arm
RF
Key
Global
Arm
RF
Key
Global
Arm
ACCESS CODES and USER DEFINITIONS FOR PARTITIONS 5 and 6
3-Digit
User #
Auth.
Level
Partition 5
Open/
Group
Close
Bypass
RF
Key
Global
Arm
3-Digit
User #
Auth.
Level
Partition 6
Open/
Group
Close
Bypass
ACCESS CODES and USER DEFINITIONS FOR PARTITIONS 7 and 8
3-Digit
User #
Auth.
Level
Partition 7
Open/
Group
Close
Bypass
RF
Key
Global
Arm
3-Digit
User #
Authority Levels: 1=Master (arm, disarm, bypass, and/or modify lower level users)
2=Manager (arm, disarm, bypass, and/or modify lower level users)
3=Operator A (arm, disarm, bypass)
4=Operator B (arm, disarm)
5=Operator C (arm, disarm only if system was armed with this code)
6=Duress code (arm, disarm, triggers silent panic alarm)
– 47 –
Auth.
Level
Partition 8
Open/
Group
Close
Bypass
Defaults:
User
4-Digits
User 1 (Installer)
5140
User 2
1234
Alpha
INSTLR
MASTER
— 48 —
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Zone
No.
Zone
Type
Part
1-8
Input
Type
Arm
w/Fault
Vent
Zone
STAY
Mode
AutoSTAY
Silent
Bypass Access Panel Tamper
Group
Point
ID #
Serial # / Loop
ZONE DEFINTION FOR ZONES 001-025
Bell/Relay
Activation
Rpt.
Code
Zone Information & Alpha
Descriptor (3 words max.)
— 49 —
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
Zone
No.
Zone
Type
Part
1-8
Input
Type
Arm
w/Fault
Vent
Zone
STAY
Mode
AutoSTAY
Silent
Bypass Access Panel Tamper
Group
Point
ID #
Serial # / Loop
ZONE DEFINTION FOR ZONES 026-050
Bell/Relay
Activation
Rpt.
Code
Zone Information & Alpha
Descriptor (3 words max.)
— 50 —
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
Zone
No.
Zone
Type
Part
1-8
Input
Type
Arm
w/Fault
Vent
Zone
STAY
Mode
AutoSTAY
Silent
Bypass Access Panel Tamper
Group
Point
ID #
Serial # / Loop
ZONE DEFINTION FOR ZONES 051-075
Bell/Relay
Activation
Rpt.
Code
Zone Information & Alpha
Descriptor (3 words max.)
— 51 —
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
Zone
No.
Zone
Type
Part
1-8
Input
Type
Arm
w/Fault
Vent
Zone
STAY
Mode
AutoSTAY
Silent
Bypass Access Panel Tamper
Group
Point
ID #
Serial # / Loop
ZONE DEFINTION FOR ZONES 076-100
Bell/Relay
Activation
Rpt.
Code
Zone Information & Alpha
Descriptor (3 words max.)
— 52 —
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
Zone
No.
Zone
Type
Part
1-8
Input
Type
Arm
w/Fault
Vent
Zone
STAY
Mode
AutoSTAY
Silent
Bypass Access Panel Tamper
Group
Point
ID #
Serial # / Loop
ZONE DEFINTION FOR ZONES 101-125
Bell/Relay
Activation
Rpt.
Code
Zone Information & Alpha
Descriptor (3 words max.)
— 53 —
128
127
126
Zone
No.
Zone
Type
Part
1-8
Input
Type
Arm
w/Fault
Vent
Zone
STAY
Mode
AutoSTAY
Silent
Bypass Access Panel Tamper
Group
Point
ID #
Serial # / Loop
ZONE DEFINTION FOR ZONES 126-128
Bell/Relay
Activation
Rpt.
Code
Zone Information & Alpha
Descriptor (3 words max.)
ZONE DEFINITIONS FOR KEYPAD PANIC ZONES 995, 996, and 999
Enter yes/no for each partition-field *22
Zone
No.
Zone
Type
1
2
3
4
5
6
7
8
Bell/Relay
Activation
Report
Code
Zone Information and
Alpha Descriptor (3 words max.)
995
(see
note
below)
996
999
NOTE: Do Not Use Zone No. 995 in a Fire Alarm application.
ZONE DEFINITIONS FOR SYSTEM ZONES; 970 − 975, 988; 990 and 997
Zone
No.
Zone
Type
Bell/Relay
Activation
Zone Information
and
Alpha Descriptor (three words max.)
Report
Code
970
971
972
973
974
975
988
990
997
— 54 —
ZONE DEFINITIONS FOR RELAY SUPERVISORY ZONES 601-632
Zone
No.
Zone
Type
Report
Code
Zone Information
and
Alpha Descriptor (3 words max.)
Zone
No.
601
617
602
618
603
619
604
620
605
621
606
622
607
623
608
624
609
625
610
626
611
627
612
628
613
629
614
630
615
631
616
632
Zone
Type
Report
Code
Zone Information
and
Alpha Descriptor (3 words max.)
NOTE: Only the relays on 4204CF modules may be supervised. If supervision is programmed for other
types of Output Devices, unpredictable results may occur.
— 55 —
ZONE DEFINITIONS FOR SUPERVISORY OF ECP DEVICE ZONES 800-830
Zone
No.
Zone
Type
Zone Information
and
Alpha Descriptor (3 words max.)
Report
Code
Zone
No.
800
816
801
817
802
818
803
819
804
820
805
821
806
822
807
823
808
824
809
825
810
826
811
827
812
828
813
829
814
830
Zone
Type
Report
Code
Zone Information
and
Alpha Descriptor (3 words max.)
815
Zone Types
00=zone not used
07=24-hour audible
16=fire w/verification
22=disarm
01=entry/exit 1
08=24-hour auxiliary
17=waterflow
23=no alarm response
02=entry/exit 2
09=supervised fire
18=supervisory
27=Not Used
03=perimeter
10=interior (delay)
19=24-hour trouble
28=Not Used
04=interior (follower)
12=Not Used
20=arm stay
29=Not Used
05=day/night burglary
13=Remote P/S
21=arm away
06=24-hour silent
14=CO Detector alarm
Input Types
00=not used
Bells/Auxiliary Relay Activation
07=Dip switch-type polling loop
0=none
4=auxiliary relay
01=hardwired
08=right loop dip switch poll loop
1=bell 1
5=bell 1 and auxiliary relay
02=RF motion transmitter
09=keypad input
2=bell2
6=bell 2 and auxiliary relay
03=supervised RF transmitter
10=Not Used
3=bells 1 and 2
7=bells 1 and 2 and auxiliary relay
04=unsupervised RF transmitter
11=Not Used
05=RF button transmitter
12=Not Used
06=serial number polling loop
13=Not Used
— 56 —
Output Devices Worksheets
Applicable only if relays (4204/4204CF) or V-Plex are used.
Output Devices – Programmed in the #93 Menu Mode in the Output Programming Section. Fill in the required data on
the worksheet below and follow the procedure in the installation instructions as you enter the data during the displays
and prompts that appear in sequence.
For 4204/4204CF, the Device Programming section must be programmed for the device address. Set the
NOTES: 1.
DIP switches on the device for that address.
2.
For V-Plex, devices must be programmed in the Zone Programming section
3.
If you are using outputs on V-Plex (e.g., 4101SN) no more than 20 of the V-Plex outputs may be
programmed for the same START or STOP condition. Also, if you are using ZONE # for the START of a
V-Plex output and want that output to stop when the same zone restores, the STOP programming MUST
BE BLANK.
S T A R T
OUTPUT
DEV #
A
EV/ZL
Zone
S T O P
ZT / P
ZL
ZT / P
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
— 57 —
Relay
Group
Restrict
0=V-Plex
1=4204/
4204CF
V-Plex Zone #
or
Dev Add
4204/4204CF
Relay # for
4204/
4204CF
OUTPUT DEVICES WORKSHEET (cont’d)
S T A R T
OUTPUT
DEV #
A
EV/ZL
Zone
S T O P
ZT / P
ZL
ZT / P
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
— 58 —
Relay
Group
Restrict
0=V-Plex
1=4204/
4204CF
V-Plex Zone #
or
Dev Add
4204/4204CF
Relay # for
4204/
4204CF
OUTPUT DEVICES WORKSHEET (cont’d)
S T A R T
OUTPUT
DEV #
A
EV/ZL
Zone
S T O P
ZT / P
ZL
ZT / P
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
— 59 —
Relay
Group
Restrict
0=V-Plex
1=4204/
4204CF
V-Plex Zone #
or
Dev Add
4204/4204CF
Relay # for
4204/
4204CF
OUTPUT DEVICES WORKSHEET (cont’d)
S T A R T
OUTPUT
DEV #
A
EV/ZL
Zone
S T O P
ZT / P
ZL
ZT / P
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
— 60 —
Relay
Group
Restrict
0=V-Plex
1=4204/
4204CF
V-Plex Zone #
or
Dev Add
4204/4204CF
Relay # for
4204/
4204CF
A = DEVICE ACTION
0 = No Response; 1 = Close for 2 sec; 2 = Close and stay closed; 3 = Pulse on and off; 4 =
Toggle alternately between START and STOP events
EV = EVENT
0 = Not used; 1 = Alarm; 2 = Fault; 3 = Trouble; 4 = Restore
ZL = ZONE LIST
01-15, 00 = Not Used
"START" ZONE LIST: Upon alarm, fault, trouble or restore of ANY zone in this list, device
action will START.
"STOP" ZONE LIST:
Upon restore of ALL zones on this list, device action will STOP. It
need not be same list as used for START.
ZT = ZONE TYPE/SYSTEM OPERATION
Choices for Zone Type/System Operation are:
00 = No Response (Not Used)
01 = Entry/Exit #1
02 = Entry/exit #2
03 = Perimeter
04 = Interior Follower
05 = Trouble Day/Alarm Night
06 = 24-Hr. Silent
07 = 24-Hr. Audible
08 = 24-Hr. Auxiliary
09 = Fire Alarm or Trouble
10 = Interior W/Delay
12 = PLM Supervision - Not
Used
13 = Remote P/S
14 = CO Detector Alarm
16 = Fire With Verification
17 = Waterflow*****
18 = Fire Supervisory
19 = 24-Hour Trouble
20 = Arming-STAY***
21 = Arming-AWAY****
22 = Disarming (Code + Off)
23 = No Alarm Response
27 = Access Point (allows more than one
relay to be controlled by activation if access
point request) - Not Used
28 = MLB Supervision - Not Used
29 = Momentary Exit - Not Used
30 = On Second Code + Off
31 = End of Exit Time
32 = Start of Entry Time
33 = Any Burglary Alarm
41 = AC Power Fail
42 = System Battery Low
43 = Communication failure
44 = RF Low Battery
45 = Polling Loop Failure
47 = Console Failure
51 = RF Receiver Failure
52 = Kissoff
54 = Fire Zone Reset
55 = Disarm + 1 Minute
56 = XX Minutes (enter XX in field 1*74) *
57 = YY Seconds (enter YY in field 1*75) *
34 = Code + [#] + 71
35 = Code + [#] + 72
36 = At Bell Timeout **
37 = 2 Times Bell Timeout **
38 = Chime
39 = Fire Alarm
40 = Bypassing
58 = Duress
60 = Audio Alarm Verification (must be
selected for both START and STOP
operation)
61 = Code + [#] + 67
62 = Bell 2 Timeout
63 = Auxiliary Relay Timeout
*
Stop condition only
** Or at disarming, whichever occurs earlier
*** The output also activates when the partition is armed in the INSTANT mode
**** The output also activates when the partition is armed in the MAXIMUM mode
***** Use an event of fault or alarm as the START option
P=
PARTITION No. 1-8, 0 = Any
ZONE LISTS FOR OUTPUT DEVICES – Programmed in the #93 Menu Mode in the Output Programming Section. Fill in the
required data on the worksheet below and follow the procedure shown earlier in this Programming Guide as you enter the
data during the displays and prompts that appear in sequence. Up to 15 zone lists may be created
NOTE:Record desired zone numbers below. More or fewer boxes than shown may be needed, as any list may include any or
all of system's zone numbers.
Zone List 1: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 2: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 3: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 4: Started or stopped by zone numbers (enter 000 to end entries).
— 61 —
Zone List 5: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 6: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 7: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 8: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 9: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 10: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 11: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 12: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 13: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 14: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 15: Started or stopped by zone numbers (enter 000 to end entries).
— 62 —
Scheduling Menu Prompts
To program schedules, enter Scheduling program mode by pressing [User Code] + # + 80 to display the first choice of the
menu driven programming functions. NOTE: Only users with an Installer or Master level user code may enter the #80 mode.
Press 0 (NO) or 1 (YES) in response to the displayed menu selection. Pressing 0 will display the next choice in sequence.
Menu selections are as follows:
PROMPT
EXPLANATION
Time Window ?
1 = YES 0 = NO
For defining up to 20 time windows each with a start and a stop time programmed by entering the hours and
minutes.
0
O/C Schedules ?
1 = YES 0 = NO
0
Holidays ?
1 = YES 0 = NO
0
Timed Events ?
1 = YES 0 = NO
Access Sched. ?
1 = YES 0 = NO
For defining the daily open and close schedules for the 8 partitions. Each partition can be programmed with
an opening and closing window for each day of the week and holidays.
For defining up to 16 holidays for which partitions they apply.
0
0
For defining up to 20 time driven events with the following parameters:
•
Time window
•
Action desired
•
Action specifier
•
Activation time
•
Days of the week
For defining the limitation of access schedules for the user codes. Each schedule can be programmed with
two window for each day of the week and holidays
#80 and #81 MENU MODE KEY COMMANDS
The following is a list of commands used while in the Menu mode.
#80 or #81
[Q]
Enters Menu mode
Serves as ENTER key. Press to have keypad accept entry.
[#]
Backs up to previous screen.
0
Press to answer NO.
1
Press to answer YES.
01-09
00
All data entries are either 2-digit entries.
Exits Menu mode, returns to normal operation mode when entered at the first question for each category.
— 63 —
Scheduling Worksheets
Time Windows Definitions Worksheet. The system provides 20 time windows that are defined with start and stop times.
They are programmed in the #80 Menu Mode. Fill in the required data on the worksheet below and follow the procedure in
the installation instructions as you enter the data during the displays and prompts that appear in sequence.
Time Window
Start Time
Stop Time
Number
(HH:MM)
(HH:MM)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
(Keep this worksheet handy, as you will be asked for a given time window number later in this section).
Because the time windows are shared among all partitions, it is important to make sure that
changing a time window does not adversely affect desired actions in other partitions.
Daily Open/Close Schedule Worksheet: Using the time windows previously defined, fill in the required data on the
worksheet below and follow the procedure in the installation instructions as you enter the data during the displays and
prompts that appear in sequence.
Part
Mon
Op
Cl
Tues
Op
Cl
Wed
Op
Cl
Thur
Op
Cl
1
2
3
4
5
6
7
8
— 64 —
Fri
Op
Cl
Sat
Op
Cl
Sun
Op
Cl
Hol
Op
Cl
Holiday Schedule Worksheet: The system provides up to 16 holidays that can be assigned for the system. Each holiday
can be assigned to any combination of partitions. Fill in the required data on the worksheet below and follow the procedure in
the installation instructions as you enter the data during the displays and prompts that appear in sequence.
HOL
Partition
Month/Day
1
/
2
/
3
/
4
/
5
/
6
/
7
/
8
/
9
/
10
/
11
/
12
/
13
/
14
/
15
/
16
/
1
2
3
4
5
6
7
8
Time-Driven Event Worksheet: The system provides up to 20 time-driven events that can be programmed for the system.
Fill in the required data on the worksheet below and follow the procedure in the installation instructions as you enter the data
during the displays and prompts that appear in sequence.
Sched
Num.
1
Time
Window
Day(s)
M T W T F S S H
Action
Desired
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
— 65 —
Action
Specifier
Activation
Time
Automatic Refresh: The system automatically updates the status of all Time-Driven Events upon any of the following
occurrences:
•
Changing of the time or date via #63 mode
•
Exiting #80 Scheduling Menu mode
•
Exiting Program mode
•
After a disconnect from the downloader
•
On a power-up
•
At Daylight Saving Time adjustment.
Below is a list of the "Action" codes (desired actions) used when programming time-driven events. Note that these codes are
independent of the "relay codes" programmed during the #93 Menu Mode–Output Programming mode. If using Time Driven
Events, the following menu items must first be programmed using #93 Menu Mode - Output Programming:
Enter Relay No. (reference identification number)
Zone No.
(V-Plex)
Relay Group
(if applicable)
ECP Address
(4204/4204CF)
Restriction
Relay No.
(4204/4204CF)
Relay Type
(V-Plex or 4204/4204CF)
Relay commands:
Action Specifier for commands 01-05 is Relay No.; Action Specifier for commands 06-10 is Relay Group No.
01 = Relay On
02 = Relay Off
03 = Relay Close for 2 seconds
04 = Relay Close XX minutes (field 1*74)
05 = Relay Close YY seconds (field 1*75)
06 = Relay Group On
07 = Relay Group Off
08 = Relay Group Close for 2 seconds
09 = Relay Group Close XX minutes (field 1*74)
10 = Relay Group Close YY seconds (field 1*75)
Arm/Disarm commands:
Action Specifier for commands 20-24 is Partition(s). Activation times 1 (Beginning), 2 (End), 3 (During), 5 (Random Start), 6
(Random End), 7 (Random During) are the only valid choices for auto-arming and disarming functions.
20 = Arm-Stay
21 = Arm Away
22 = Disarm
23 = Force Arm Stay (Auto-bypass faulted zns)
24 = Force Arm Away (Auto-bypass faulted zns)
25 = Arm Instant
26 = Arm Maximum
Bypass commands:
Action Specifier for commands 30-31 is Zone List #, Activation times 1 (Beginning), 2 (End), 3 (During), 5 (Random Start), 6
(Random End), 7 (Random During) are the only valid choices for bypass commands.
30 = Auto bypass - Zone list
31 = Auto unbypass - Zone list
Open/Close Windows:
Action Specifier for commands 40-41 is Partition(s), for 42 is Access Group and for 50 no specifier is programmed.
Activation time 3 (During), 7 (Random During) are the only valid choices for these commands.
40 = Enable Opening Window
41 = Enable Closing Window
42 = Enable Access Window
50 = Off-Normal Reminder (Starts local keypad beeping if off-normal condition exists)
Additional Commands
Action Specifier for command 78 is Group.
78 = Access Point Group Disable
— 66 —
Activation time:
Refers to when the action is to take place relative to the time window.
1 = Beginning of time window
4 = Beginning and end of time window
2 = End of time window
5 = Random Start of the time window ✳
3 = During time window active period only (On at
6 = Random End of the time window ✳
beginning of window, off at end).
7 = Random During the time window ✳
✳ The activation time of the window is randomized up to 30 minutes and is initialized by either of two methods:
a. [User Code] + [#] + [41] − Initiates the random schedule for all devices in the partition.
b. [User Code] + [#] + [42] − Initiates the random schedule for all devices in the partition with a time window within 6
PM and 5 AM.
Limitation of Access Worksheet The system provides up to 8 Access Schedules that can be programmed for the system.
Fill in the required data on the worksheet below and follow the procedure in the installation instructions as you enter the data
during the displays and prompts that appear in sequence.
Acc
Sch
Mon
W1
Tues
W2
W1
W2
Wed
W1
W2
Thurs
W1
Fri
W2
W1
Sat
W2
W1
Sun
W2
W1
W2
Hol
W1
W2
1
2
3
4
5
6
7
8
Temporary Schedule #81 Menu Mode. The system provides a Temporary Schedule for each partition. Enter the temporary
scheduling mode by pressing [Installer Code] + [#] + [81]. Fill in the required data on the worksheet below and follow the
procedure in the installation instructions as you enter the data during the displays and prompts that appear in sequence.
Partition/Windows
1
Mon
Tue
Wed
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
2
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
Start Time
HH:MM
Stop Time
HH:MM
— 67 —
Thu
Fri
Sat
Sun
Partition/Windows
3
Mon
Tue
Wed
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
4
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
5
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
6
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
7
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
8
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
Start Time
HH:MM
Stop Time
HH:MM
— 68 —
Thu
Fri
Sat
Sun
NOTES
— 69 —
NOTES
— 70 —
— 71 —
8 Seconds
8 Seconds
8 Seconds
Control Unit Delay, Seconds
Model
BL
BL
OUTPUT
1
+
2k
2k
(NOTE 5)
2. See instructions on setting addresses & for
max # of keypads and wire run length
restrictions.
7. If supervision of the batteries is required, they
should be connected to the Battery Sense
Module. The Battery Sense Module is then
connected to the panel. Refer to the Battery
Sense Module instructions for connections.
6. 2k EOLR is Ademco Model EOL20.
5. Maximum Loop Impedance is 1.17 ohms.
4. No more than one (1) wire per terminal may
be connected.
3. Use only 14-22 AWG wire.
6
9
+
10
6 7 8
9
13
Blk Grn
12
KEYPAD PORT #1
Red
+
11
14
Yel
ECP Bus: Max. Line Impedance: 50 Ohms
Special Application Circuit.
Fire & Burglary Devices on the ECP Bus
must be isolated using an ECP Isolator.
Refer to Instructions for specific examples.
2k
N.O.
N.C.
ZONE 8
Maximum Loop I: 9mA
Maximum Loop V: 13.3VDC
Loop Short: 0 - 2.2V - (0 - 300 ohms)
Loop Normal: 5 - 9V (0.9k - 3.4k)
Loop Open: 10V - 13.3V, 3.8k -
ZONE INPUT SPECIFICATIONS
FOR INSTRUCTIONS
SEE 800-06306,
DATED 4/10
- Maximum fire loop capacitance
is 100 uf.
2k
N.O.
N.C.
ZONE 4
21
ZONE 5
2k
N.O.
N.C.
22
23
ZONE 6
24
2k
N.O.
N.C.
ZONE 7
2k
N.O.
N.C.
25
26
ZONE 8
TEST BURGLARY SYSTEM WEEKLY
ZONE 9
Maximum Loop I: 4mA
Maximum Loop V: 13.3V
Loop Short: NA
Loop Normal: 0 - 1.5V (0 ohms - 400 ohms)
Loop Open: 5.3V, 2.2k -
The Main Dialer Complies with
FCC Rules, Part 68
FCC Reg. No.: AC3-USA-68192-AL-E
Ringer Equivalence: 0.7B
2k
N.O.
N.C.
GLASS
BREAK
WARNING:
TO PREVENT
RISK OF
ELECTRICAL
SHOCK,
DISCONNECT
TELCO
JACK BEFORE
SERVICING
THIS PANEL
PHONE JACK
RJ31X
Connect
RJ31X using
cable supplied.
Supervision is
programmable
The impedance at which a ground
fault is annunciated is 1,000 ohms
See instructions for
proper earth ground
connections
W6
(BLUE)
MAIN DIALER ON HOOK
VOLTAGE THRESHOLD
INTACT:25V
CUT: 13V
EARTH GROUND
30
ASSEMBLED
IN MEXICO
V128FBPN-SOC-V1
See instructions for compatible devices and for max
wire run length. Fire and Burglary devices on the
polling loop must be isolated by use of a 4297 or
VSI module. Refer to instructions for specific examples.
Polling Loop: Class B, Style 3.
Polling Loop Ratings:
(supervised) 128mA max. See note 1.
8-11 VDC
20 Ohms Max. Impedance
TO OTHER DEVICES
4208U
5193SD
SMOKE
4208SNF
+
29
MAIN
J3
INTERFACE TO 5140DLM
NOTE: J2 Voltage triggers can only be used with the
4146 keyswitch for fire applications. Trigger Wiring
must be run in conduit within 20ft of the Control Panel.
1 2 3 4 5 6 7 8 9
VOLTAGE
J2
TRIGGERS
(not supervised)
Make connections using 4142TR cable
J2 VOLTAGE TRIGGERS
See instructions for trigger use and programming
(default functions shown)
1. OUT 4 (SILENT PANIC/DURESS)
2. OUT 7 (TROUBLE)
3. OUT 3 (BURGLARY/AUDIBLE PANIC)
4. OUT 6 (SUPERVISORY)
5. OUT 2 (FIRE)
6. OUT 5 (REMOTE KEYPAD SOUNDER)
7. OUT 1 (OPEN/CLOSE)
8. GROUND
9. IN 1 (N.O. LOOP)
RATINGS: OUT 1, 5, 7:
LOW: 2K TO GROUND
HIGH: 10 - 14VDC, 20mA MAX
OTHER OUTS: LOW: 1K TO GROUND
HIGH: 10 - 14VDC THRU 5K
POLLING
LOOP
27 27 28
CONNECTION OF THE FIRE ALARM
SIGNAL TO A FIRE ALARM HEADQUARTERS OR A CENTRAL STATION
SHALL BE PERMITTED ONLY WITH
THE APPROVAL OF THE LOCAL
AUTHORITY HAVING JURISDICTION.
THE BURGLARY ALARM SIGNAL
SHALL NOT BE CONNECTED TO A
POLICE EMERGENCY NUMBER.
• All zones are Class B and provide Style B supervision
• Zone resistance (excluding EOLR):
- Zones 1, 2, 8: 100 ohms max
- Other zones: 300 ohms max
• Zone response: 350 - 500mS (all zones)
• Do not mix fire and burg. sensors on one loop.
N.C. contacts for burg. usage only.
• Voltage rating, all zones - 12VDC.
20
ZONE 3
PINS 2, 3, 6, 8 & 9 NOT USED
J4 KEYPAD PORT #2
See instr. regarding port #2 use
1. GROUND (to keypad black wire)
4. DATA IN 2 (to keypad green wire)
5. AUX PWR #2 (to keypad red wire)
Rating: 10 - 14 VDC,
400mA max. See note 1
7. DATA OUT 2 (to keypad yellow wire)
19
BACK-UP DIALER EARTH
GROUND SCREW
(wire to main PCB
terminal #30)
(connect using supplied cable)
Supervision is programmable
OPTIONAL 5140DLM BACK-UP DIALER MODULE
MAIN PCB SHIELD
ZONE 1-8 NOTES
• Ratings for zones 1,2:
- 2mA max for all smoke det.
(up to 16 detectors of the type
specified in the instructions can
be used)
- UL compatibility ID: A
2k
N.O.
N.C.
Connect to main PCB
header J3 using ribbon
cable (supplied)
BACK-UP TLM ON HOOK
VOLTAGE THRESHOLD (BLUE)
INTACT: 25V
CUT: 13V
BACK-UP PHONE JACK
SEE TELCO
JACK SHOCK
RJ31X
WARNING
BELOW
Attach 5140DLM module to main PCB shield using
4 standoffs (supplied)
The 5140DLM Dialer
Complies with FCC Rules, Part 68
FCC Reg. No.: AC398U-68628-MO-N
Ringer Equivalence: 0.7B
BACK-UP LINE SEIZE
LED (GREEN)
VISTA-128FBPN SUMMARY OF CONNECTIONS
ZONES 2-7 EOLR CONFIG.
Maximum Loop Current (short loop): 7.4mA
Maximum Loop Voltage (open loop): 13.3VDC
Loop Short: 0V - 1.5V - 300 ohms total resistance)
Loop Normal: 4.2 - 6.8V, 1.2k - 2.6k
Loop Open: 7.2V - 13.3V, 3k -
ALL POWER-LIMITED WIRING MUST BE
SEPARATED FROM NON-POWER LIMITED
AND HIGH VOLTAGE WIRING BY 1/4 INCH
(6.4 mm)
For commercial fire, bell timeout must be a minimum of
6 minutes.
ALL CIRCUITS ARE POWER LIMITED EXCEPT THE OUTPUT
OF THE 1451 TRANSFORMER AND BACKUP BATTERIES.
BURG CKTS: Supervision not req'd. EOLRs not req'd.
May use non polarized devices.
1.7A max. See note 1, see instructions for compatible devices.
FIRE CKTS: Use only devices listed as Special Application
NAC Devices in Installation and Setup Guide. Supervise
using 2k EOLR. Use polarized sounding devices and
backup batteries.
N.O.
N.C.
18
ZONE 2
SMOKE
17
SMOKE
16
ZONE 1
2k (note 6)
15
J4
REMOTE KEYPADS:
6160, 6160CR-2,
AUX RELAY (FORM C)
SEE NOTE 2
programmable response
(not supervised)
Contact Rating:
28VAC/VDC, 2.8A AUXILIARY POWER #1
resistive loads
1.0A MAX (STANDBY) (For Canada 650mA)
1.7A MAX (ALARM) (See Note 1.)
Max. Impedance: 0.6 Ohms
Special Application Circuit.
8
AUX. RELAY
7
5
Make connections using
4142TR cable (supplied)
2 3 4
KEYPAD PORT #2
1
Each output is Class B and may be selected for Style Y
supervision or no supervision. (See main PCB jumpers
W1, W4 and #93 Menu Mode.)
ALARM POLARITY SHOWN
HORN
BELL
+
BELL 2
5
HORN
BELL
4
BELL OUTPUTS
BELL 1
3
W4
(WHITE)
W1
(WHITE)
1. The combined standby current drawn from
aux pwr #1, aux pwr #2 and polling loop
cannot exceed 1.0A (for Canada, 650mA).
The combined alarm current drawn from aux
pwr #1, aux pwr #2, polling loop, bell 1 and
bell 2 cannot exceed 2.3A
(for Canada, 1.95A).
NOTES
OUTPUT: 18VAC
72VA
2
TRNSFMR
TRANSFORMER
W/ENCLOSURE
ADEMCO No.1451 WH
BLACK
(supplied)
INPUT: 120VAC,
INPUT
60HZ,
1.0A max. Connect to a
dedicated circuit.
AC WIRING IS
SUPERVISED
OPTIONAL REMOVABLE
TERMINAL BLOCK KIT:
ADEMCO NO. 4142BLK
BELL 2
N.O
.
BELL 1
LE
PO
Connect to 12V, 12AH min/34.4AH max
lead acid batteries using cables supplied.
See instructions for required capacity.
Float charging voltage: 13.7VDC. Battery
normally need not be replaced for
at least 3 yrs.
BELL CIRCUIT SUPERVISION JUMPERS
DO NOT CUT
N.C
.
SP
A
PO RE A
WR
U
#1 X
Special Application Circuit
Connect Only Fire Keypads to
AUX PWR # 2.
Data in
RED
Data out
+
2-WIRE SMOKE
DETECTOR LOOP
BATTERY TABS
(SEE NOTE 7) BLK
This equipment should be installed in accordance with the National Fire Protection Association's Standard 72
(National Fire Protection Assoc., Batterymarch Park, Quincy, MA. 02169). Printed information describing
proper installation, operation, testing, maintenance and repair service is to be provided with this equipment.
Delay, Seconds
Smoke Detector
THE DELAY TIME MARKED ON THE INSTALLED DETECTOR(S) IS TO BE USED.
Zone 1
Zone 2
Aux Relay
Circuit (zone)
This unit includes a Fire Alarm Verification feature that will result in a delay of
the System Alarm Signal from the indicated Fire Alarm circuits. The total delay
(Control Unit plus Smoke Detectors) shall not exceed 30 seconds. No other
Smoke Detector shall be connected to these circuits unless approved by the
local authority having jurisdiction.
PROGRAMMABLE
AS TAMPER LOOP
WARNING:
2-WIRE SMOKE
DETECTOR LOOP
TYPES OF FIRE SIGNALLING SERVICE:
Manual fire alarm, automatic fire alarm, sprinkler supervisory and waterflow alarm, DACT, Radio Frequency (RF) and Multiplex.
UL Listed local control (non-coded). UL Listed central station and remote station protected premises unit when used with
5140DLM back-up dialer module. Installation limits under jurisdiction of local authority.
PROGRAMMABLE
AS KEYSWITCH LOOP
FOR DRY, INDOOR USE ONLY
COMMERCIAL FIRE AND BURGLAR ALARM PROTECTED PREMISES CONTROL UNIT
2-WIRE GLASS BREAK
DETECTOR LOOP
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2010 Honeywell International Inc.
www.honeywell.com/security
Ê800Ê800-063086Š
800-06308 4/10 Rev. B