Wzzard™ Starter Kits
HVAC Monitoring Bundle
SETUP MANUAL
HVAC MONITORING BUNDLE
Advantech B+B SmartWorx - Americas
707 Dayton Road
Ottawa, IL 61350 USA
Phone (815) 433-5100
Fax (815) 433-5105
Advantech B+B SmartWorx - European Headquarters
Westlink Commercial Park
Oranmore, Co. Galway, Ireland
Phone +353 91-792444
Fax +353 91-792445
www.advantech-bb.com
support@advantech-bb.com
Document Number: 2009WSKH00_R0_BB-WSK-HAC-1_2517m
2
HVAC MONITORING BUNDLE
CONTENTS
HVAC MONITORING STARTER KIT ......................................................................................................................4
WZZARD NETWORK SETUP ..................................................................................................................................4
DOWNLOADING THE HVAC MONITOR NODE RED FLOW TO THE GATEWAY ........................................5
POWER UP WZZARD EDGE NODE ....................................................................................................................10
ACCESS Node-RED UI IN THE GATEWAY ........................................................................................................11
NETWORK HEALTH PAGE ....................................................................................................................................12
ATTACHING THE SENSORS ON THE INTELLIGENT EDGE NODES ..........................................................12
ACCESSING THE DASHBOARD ..........................................................................................................................15
SETTING UP AN E-MAIL ACCOUNT ...................................................................................................................16
SETTING UP YOUR DROPBOX FOR LOGGING...............................................................................................18
APPENDIX A. CARRIER TEXT MESSAGING URL ADDRESSES ..................................................................20
Node-RED™ SOFTWARE LICENSE ....................................................................................................................22
B+B SMARTWORX TECHNICAL SUPPORT ......................................................................................................23
3
HVAC MONITORING BUNDLE
HVAC MONITORING STARTER KIT
Kit Model BB-WSK-HAC-1
The Wzzard™ HVAC Monitoring Application makes it simple to see the real time and historical
electrical consumption of any individual machine or panel. Data can be exported to Dropbox for
further analysis. Email or text message alerts can be sent when user-configured high or low
limits are exceeded in critical applications.
Installation costs are kept low using the Wzzard wireless sensing platform. The platform creates
a self-forming, self-healing wireless mesh network that eliminates the need for wires and
requires no special skills to install. Each Wzzard sensor node is powered by long life batteries.
Using Node-RED™, a simple, browser based application preinstalled on the gateway, you can
monitor current draw from any web browser on your network.
The contents of the kit include:
Qty 1 WSD2CJA
2 analog-in + 2 J-Type thermocouple inputs Wzzard Node
Qty 2 JC10F50-V
50A clamp on current sensor
Qty 2 BB-WTJ-10-36-TT
J-Type thermocouple, #10 mounting hole, ungrounded
Qty 1 SG3000525-41
SmartSwarm 341™ Ethernet Gateway, with Dust
WZZARD NETWORK SETUP
The Wzzard node and gateway in this kit are preconfigured. If this is the only Wzzard device in
your vicinity, it will need no further configuration. If other Wzzard gateways are nearby, you will
need to change the network ID on both the gateway and the node. See respective node and
gateway manuals for instructions.
4
HVAC MONITORING BUNDLE
DOWNLOADING THE HVAC MONITOR NODE RED FLOW TO THE GATEWAY
Note: router must be in operational and online state in order to add the HVAC application (ie Eth1
must be plugged in).
1. Follow the instructions in the Gateway Quick Start Guide to claim your gateway.
2. Select View Devices from the dropdown menu on the SmartWorx Hub Home Screen:
3. Select your device from the list of available devices:
5
HVAC MONITORING BUNDLE
4. Select Add/Upgrade Apps:
5. Check the box next to HVAC. A list of components to be updated will appear:
6
HVAC MONITORING BUNDLE
6. Click OK to accept the download:
7. Click Add/Upgrade Selected to start the download:
7
HVAC MONITORING BUNDLE
8. The download could take several minutes. To monitor the progress, Select History from the
Manage Devices screen:
8
HVAC MONITORING BUNDLE
9. As each component is updated, it will be marked with a  check mark:
Note: “AddNode” commands will show an X if they have already been installed.
9
HVAC MONITORING BUNDLE
POWER UP WZZARD EDGE NODE
1. Loosen the (4) black screws that hold the top of the node in place.
2. Install your batteries.
3. Note: Use (2) 3.6V 2400 mAH Lithium Thionyl Chloride AA batteries.
4. Install the battery clip.
5. Replace the cover. Tighten the (4) top screws to maintain IP67 rating. Torque each screw to
5 to 8 in-lb (0.6 to 0.9 Nm). This is equivalent to 1/4 to 1/2 turn after screw makes contact.
6. Check LED.
After you have installed the batteries, the LED will begin to blink. This indicates that the Node is
attempting to establish a network connection. The LED will cease blinking when a connection is
made.
Data
LED Indicator
Status
Solid ON
Slow Blink
(1 per second)
Fast Blink
(10 per second)
OFF
Module startup initialization (approx. 10 seconds)
Attempting to establish connection with SmartMesh IP network.
Firmware update in progress.
Unit is connected to wireless network.
1. Attach the External Antenna.
Note: The best way to remove the clip is to insert a
small flathead screwdriver between the batteries
and the clip, parallel to the batteries, and give the
screwdriver a gentle twist. This will remove the clip
without damage.
10
HVAC MONITORING BUNDLE
ACCESS Node-RED UI IN THE GATEWAY
1. Attach the antenna to the Wzzard™ antenna port on the gateway.
2. Attach the Ethernet cable to the ETH0 port on the gateway and the other end to your PC.
You will use an Ethernet connection to configure the gateway and to communicate with it.
3. Attach the supplied power supply and plug it in.
4. Open a browser on your computer and open the Node-RED™ configuration page. The
default address is: 192.168.1.1:1880/ui. (Chrome or Firefox recommended.)
5. The Wzzard Node information values will populate when the node joins the network.
6. You can set up a phone number to receive text messages and/or an e-mail address for
receiving alerts on this page. For text messaging, you will need to select the cell carrier of
the receiving phone. If the carrier is not on the list, select custom, and add the URL of the
carrier to the phone number (ie: 1-123-2345@txt.abcphone.com). See Appendix A for
carrier text addresses. If your carrier is not listed, contact your carrier for the address of their
SMS gateway.
7. You can enable or disable alerts as well as setting the trigger values on this page also.
11
HVAC MONITORING BUNDLE
NETWORK HEALTH PAGE
1. Click the “Network Health” button on the lower left corner of the Configuration page. The
page below appears. This page shows the status of the network.
ATTACHING THE SENSORS ON THE INTELLIGENT EDGE NODES
1. Wire Your Sensors to the Edge Node.
The Wzzard™ HVAC monitoring kit comes with two AC current sensors and two J-Type
Thermocouples.
Sensor
Compressor
Current
Fan
Current
Temp In
Temp Out
Wzzard Industrial Node with S&T cable
Connection
Sensor (+) to Stripped & Tinned Cable
Sensor (-) to Stripped & Tinned Cable
Sensor (+) to Stripped & Tinned Cable
Sensor (-) to Stripped & Tinned Cable
Sensor (+) to Internal Terminal Block
Sensor (-) to Internal Terminal Block
Sensor (+) to Internal Terminal Block
Sensor (-) to Internal Terminal Block
RED
PINK
YELLOW
GREEN
1
2
3
4
12
HVAC MONITORING BUNDLE
Current Sensors
• Open the wire protector clamp by pushing it away from the sensor body.
• Attach your wires.
• Close the wire protector clamp.
13
HVAC MONITORING BUNDLE
Temperature Sensors
1 = Thermocouple input #1 positive (+)
2 = Thermocouple input #1 negative (-)
3 = Thermocouple input #2 positive (+)
4 = Thermocouple input #2 negative (-)
2. Mount Your Sensors.
Current Sensors
The sensor can be mounted in any position.
Open the clamp release by pushing it away from the sensor body. Run the wire you are
monitoring through the opening in the sensor.
Close the sensor firmly around your wire and ensure that the clamp release has snapped back
into place.
14
HVAC MONITORING BUNDLE
ACCESSING THE DASHBOARD
1. Open a browser on your computer and open the Node-RED™ configuration page. The
default address is: 192.168.1.1:1880/ui
2. Click on the “Dashboard” button on the lower left corner of the configuration page.
3. The dashboard should look like the following screen.
4. You can switch to the Configuration page or Network Health page by clicking on their
respective buttons on the lower left.
15
HVAC MONITORING BUNDLE
SETTING UP AN E-MAIL ACCOUNT
1. From your browser, open the Node-RED™ flow at 192.168.1.1:1880.
2. Locate “Energy Page”, then scroll right and locate the green “Send Email” node; double click on it.
16
HVAC MONITORING BUNDLE
3. Enter your UserID and Password for your e-mail server in the appropriate boxes. (Leave
the “To” field blank.)
Note: If you are using a G-Mail account, you will need to enable “Less Secure
Apps” in the Google security settings. See below.
4. Click “Done”. Then Click the “Deploy” button in the upper right corner of the page.
17
HVAC MONITORING BUNDLE
SETTING UP YOUR DROPBOX FOR LOGGING
1. Log in to your Dropbox account or sign up for a new one.
2. Once signed up or logged in:
•
Go to https://www.dropbox.com/developers
•
Click 'Create your app' box in the center of the screen.
•
Select 'Dropbox API app'.
•
Choose an appropriate answer as to whether your node should be limited to its own
folder or given full access. (TIP: This can be changed later, so choose 'Yes' to restrict
the application while testing might be a good idea.)
•
Choose an app name.
•
Click 'Create app'.
The subsequent app page will contain the App Key, App Secret and a 'Generate' button
to produce a suitable 'access token'. Save these strings so you can enter them into the
application later.
3. From your browser, open the Node-RED™ flow at 192.168.1.1:1880.
4. Locate “Log data to file”, then scroll right and locate the blue ‘Write Remote File’ node;
double click on it.
18
HVAC MONITORING BUNDLE
5. Then click on the pencil icon next to the Dropbox text window.
6. Fill in the App Key, App Secret, and Access Token you got from Dropbox in their
respective fields. (See yellow box for more information.)
7. Click Updated; then Done again to close both windows.
8. Click the “Deploy” button in the upper right corner of the page.
9. Enable logging on the Dashboard web page.
19
HVAC MONITORING BUNDLE
APPENDIX A. CARRIER TEXT MESSAGING URL ADDRESSES
U.S.A Carriers
Alltel
AT&T (formerly Cingular)
Boost Mobile
Nextel (now Sprint Nextel)
Sprint PCS (now Sprint Nextel)
T-Mobile
US Cellular
Verizon
Virgin Mobile USA
[10-digit phone number]@message.alltel.com
Example: 1234567890@message.alltel.com
[10-digit phone number]@txt.att.net
[10-digit phone number]@cingularme.com
Example: 1234567890@txt.att.net
[10-digit phone number]@myboostmobile.com
Example: 1234567890@myboostmobile.com
[10-digit telephone number]@messaging.nextel.com
Example: 1234567890@messaging.nextel.com
[10-digit phone number]@messaging.sprintpcs.com
Example: 1234567890@messaging.sprintpcs.com
[10-digit phone number]@tmomail.net
Example: 1234567890@tmomail.net
[10-digit phone number]email.uscc.net (SMS)
Example: 1234567890@email.uscc.net
[10-digit phone number]@vtext.com
Example: 1234567890@vtext.com
[10-digit phone number]@vmobl.com
Example: 1234567890@vmobl.com
International Carriers
Email to SMS Gateway
7-11 Speakout (USA GSM)
number@cingularme.com
Airtel (Karnataka, India)
number@airtelkk.com
Airtel Wireless (Montana, USA)
number@sms.airtelmontana.com
Alaska Communications Systems
number@msg.acsalaska.com
Aql
number@text.aql.com
AT&T Enterprise Paging
number@page.att.net
BigRedGiant Mobile Solutions
number@tachyonsms.co.uk
Bell Mobility & Solo Mobile (Canada) number@txt.bell.ca
BPL Mobile (Mumbai, India)
number@bplmobile.com
Cellular One (Dobson)
number@mobile.celloneusa.com
Cingular (Postpaid)
number@cingularme.com
Centennial Wireless
number@cwemail.com
Cingular (GoPhone prepaid)
number@cingularme.com (SMS)
Claro (Brasil)
number@clarotorpedo.com.br
Claro (Nicaragua)
number@ideasclaro-ca.com
Comcel
number@comcel.com.co
Cricket
number@sms.mycricket.com (SMS)
CTI
number@sms.ctimovil.com.ar
Emtel (Mauritius)
number@emtelworld.net
Fido (Canada)
number@fido.ca
General Communications Inc.
number@msg.gci.net
20
HVAC MONITORING BUNDLE
Globalstar (satellite)
number@msg.globalstarusa.com
Helio
number@messaging.sprintpcs.com
Illinois Valley Cellular
number@ivctext.com
Iridium (satellite)
number@msg.iridium.com
Iusacell
number@rek2.com.mx
i wireless
number.iws@iwspcs.net
Koodo Mobile (Canada)
number@msg.koodomobile.com
LMT (Latvia)
number@sms.lmt.lv
Meteor (Ireland)
number@sms.mymeteor.ie
Mero Mobile (Nepal)
977number@sms.spicenepal.com
MetroPCS
number@mymetropcs.com
Movicom (Argentina)
number@sms.movistar.net.ar
Mobitel (Sri Lanka)
number@sms.mobitel.lk
Movistar (Colombia)
number@movistar.com.co
MTN (South Africa)
number@sms.co.za
MTS (Canada)
number@text.mtsmobility.com
Nextel (United States)
number@messaging.nextel.com
Nextel (Argentina)
TwoWay.11number@nextel.net.ar
Orange Polska (Poland)
9digit@orange.pl
Personal (Argentina)
number@alertas.personal.com.ar
Plus GSM (Poland)
+48number@text.plusgsm.pl
President’s Choice (Canada)
number@txt.bell.ca
Qwest
number@qwestmp.com
Rogers (Canada)
number@pcs.rogers.com
SL Interactive (Australia)
number@slinteractive.com.au
Sasktel (Canada)
number@sms.sasktel.com
Setar Mobile email (Aruba)
297+number@mas.aw
Suncom
number@tms.suncom.com
T-Mobile (Austria)
number@sms.t-mobile.at
T-Mobile (UK)
number@t-mobile.uk.net
Telus Mobility (Canada)
number@msg.telus.com
Thumb Cellular
number@sms.thumbcellular.com
Tigo (Formerly Ola)
number@sms.tigo.com.co
Tracfone (prepaid)
number@mmst5.tracfone.com
Unicel
number@utext.com
Virgin Mobile (Canada)
number@vmobile.ca
Vodacom (South Africa)
number@voda.co.za
Vodafone (Italy)
number@sms.vodafone.it
YCC
number@sms.ycc.ru
MobiPCS (Hawaii only)
number@mobipcs.net
21
HVAC MONITORING BUNDLE
Node-RED™ SOFTWARE LICENSE
Copyright (2017) (B+B SmartWorx)
Node-RED is licensed under the Apache License, Version 2.0 (the "License"),
You may not use Node-RED software preinstalled in the SmartSwarm Gateway except in compliance with the License. You may obtain a copy of the License at:
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software distributed under the License is
distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND,
either express or implied.
See the License for the specific language governing permissions and limitations under the License.
22
HVAC MONITORING BUNDLE
B+B SMARTWORX TECHNICAL SUPPORT
Phone:
1 (800) 346-3119
Monday - Friday, 7 a.m. to 5:30 p.m. CST
Fax:
(815) 433-5109
Email:
B+B SmartWorx Technical Support
Web:
http://www.advantech-bb.com
Document Number: 2009WSKH00_R0_BB-WSK-HAC-1_2517m
23
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
B+B SmartWorx:
BB-WSK-HAC-1
Download PDF

advertising