Arri L10-C Fresnel User Manual

L-Series®
L10
User Manual
December 2015
© 2015 Arnold & Richter Cine Technik GmbH & Co. Betriebs KG. All rights reserved.
No part of this document may be used for distribution, reproduction, transmission, transcription, storage in a data retrieval system, or translated into any language in any form by any means without the prior written permission of ARRI®. If you are downloading files from our web pages for your personal use, make sure to check for updated versions. ARRI® cannot take any
liability whatsoever for downloaded files, as technical data are subject to change without notice.
L5.0006896
Dimensions
Dimensions
3
Content
Content
Dimensions ..................................................................................................................................................... 3
Safety Information .......................................................................................................................................... 6
Explanations of Warning Signs and Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
General Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Specific Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Maintenance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Legal disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Introduction .................................................................................................................................................. 10
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Overview ....................................................................................................................................................... 12
Physical Installation ..................................................................................................................................... 14
To adjust the stirrup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
To mount the spigot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Basic features ............................................................................................................................................... 15
Control options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Connector Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Power ............................................................................................................................................................ 17
AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Fixture menu ................................................................................................................................................. 18
Overview of the fixture menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Features of the fixture menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
To read out fixture information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
4
Content
Short cuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DMX control .................................................................................................................................................. 23
DMX mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
DMX data link ................................................................................................................................................ 24
Tips for reliable data transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
To connect the data link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Fixture Menu ................................................................................................................................................. 26
Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Fixture Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
RDM commands ........................................................................................................................................... 29
Required RDM command extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Manufacturer commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
ARRI Lighting Service Manager .................................................................................................................. 32
Error messages ............................................................................................................................................ 33
DMX protocol ................................................................................................................................................ 34
ARRI L10-TT (Tungsten Tuneable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
ARRI L10-DT (Daylight Tuneable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
ARRI L10-C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Specifications ............................................................................................................................................... 47
5
Safety Information
Safety Information
Always follow these instructions to protect against
injury to yourself and damage to the product or other
objects.
Explanations of Warning Signs and Indications
Possible risk of injury or damage to equipment.
Risk of fire or electric shock. Possible risk of injury or
damage to equipment.
Caution! Hot surface. Possible high surface temperature. Risk of injury through burns.
Caution! High intensity light emission. Risk of eye
injury.
Note: Indicates further information.
General Notes
• This document contains important instructions and notes to
handle the product safe.
• Always follow all safety information for your own protection.
• Please contact a trained ARRI® service technician to do any
service and maintenance not described in this manual
• Please follow the user manual of accessories and third party
accessories, like motorized yokes. They contain important
safety and security information.
• Read the user manual and installation manual which are
shipped with accessories for the ARRI® L-Series®.
• Retain this user manual and all user and installation manuals
shipped with the system for further reference and possible
new owners of this product.
• ARRI® L-Series® products are intended for professional use
and may only be operated by qualified persons. They are not
for household use.
• Help protecting the environment by disposing the package
material at your local recycling center.
• All components comply to the guidelines listed below:
Low voltage directive 2014/35/EU
EMC directive 2014/30/EU
RoHS directive 2011/65/EU
6
Read and understand all safety information and operation instructions before you operate or install the
product or the system.
Use only genuine spare parts or accessories that
have been recommended or approved by ARRI.
Other accessories or spare parts may cause hazards,
damage the product or invalidate the warranty.
Check all cables and devices for visible damage
before you work with the system. Defective electric or
electronic devices must not be used. Take special
care of the following components:
Component
Possible damage
Housing, lens
Cracks, cuts, deformation
Cables
Cuts, deformation, burns
Connectors
Cracks, deformation, burns
Cable connectors
Damaged
Threads
Damaged
If the product or accessory is visibly damaged, the
product or accessory must no longer be used.
Replace or repair the respective part. In case of
repairs, please contact an authorized ARRI service
center.
Never attempt to repair any part of the product on
your own. Maintenance and repair work is only to be
carried out by an authorized ARRI service center.
Safety Information
General Safety Information
Do not operate the product if the ambient temperature exceeds 45° C (113° F). Observe all information
given in chapter “Specification” on page 47.
Do not expose the product to rain or moisture. Do not
use the product for 2 h when it was exposed to big
temperature differences as condensed moisture may
damage the product electrically when switched on.
Do not bypass any safety feature of the product.
Do not open the product. There are no user serviceable parts inside. The housing is sealed with an adhesive seal that will break immediately when trying to
open the housing. Doing so will invalidate the warranty.
7
Safety Information
In addition to regular visible checks ARRI recommends that all electric components are checked for
electrical safety by a professional every 12 month.
Keep the protocol of the check.
Specific Safety Information
Intensive use can cause the surface and the heat sink
to become warm. Let the product cool down complete
before you handle it.
Never cover air vents and the heat sink during operation. Keep a minimum clearance around the product
of 0.5 m (1.65 ft).
WARNING! Intense light. Never look direct into the
light source.
Never point a light beam from another luminaire into
the light source. Do not place the product on heat
sources. Intense heat cause automatic power off during operation.
WARNING! The stirrup must be mounted hanging or
standing vertically. Lateral load can cause deformation or breaking of the spigot and the stirrup.
Devices and accessories must be secured against fall
when mounted above floor level. Always observe
common and local safety regulations.
8
Never use the cables for transportation. Never hang
the product on its cables.
CAUTION! High voltage! Always disconnect the product complete from mains voltage before you connect
or disconnect a cable.
Always check that the local AC power matches the
voltage and frequency range printed on the type label
of the product before use. Never use the product
when the AC power does not match.
The product must not be used on a surface without a
skid (accessory) mounted. To do so causes overheating.
Never connect the product to a dimmer-system or a
dimmer-channel in non-dim mode. To do so will damage the electronics. Damages caused by connecting
the product to a not suitable power source are not
covered by the warranty.
Always keep cables away from the product during
operation. Do not tilt the power cable directly after the
connector. Water could immerse and cause short circuits and damage the connector.
Disconnect all cables prior to transport.
Please observe the information given in the „Safety leaflet
ARRI lampheads“ (L5.40731.E). The leaflet is available for
download on our web site www.arri.com.
Maintenance Information
• Do not clean the surface of the product with solvents or strong
detergents.
• Clean the product with a soft cloth wetted with a mild detergent. Do not rub the surface: lift stuck particles off with a soft
repeated press.
Legal disclaimer
© 2015 Arnold & Richter Cine Technik GmbH & Co. Betriebs
KG (ARRI). All rights reserved. Information subject to change
without notice. ARRI and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential
or economic loss or any other loss occasioned by the use of,
inability to use or reliance on the information contained in this
document. The ARRI logo, the ARRI name and all other trademarks in this document pertaining to services or products by
ARRI or its affiliates and subsidiaries are trademarks or licensed by ARRI or its affiliates or subsidiaries.
Safety Information
Not to observe these safety information or to ignore
common sense may cause serious injury or even
death. Damage to the product or other devices is possible.
ARRI and the ARRI logo are registered trademarks of the
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG.
Intended use
• Clean soiled electric contacts with cotton swabs wetted with
isopropyl alcohol.
This product is intended to illuminate persons and objects in a
dry environment.
• Keep electric contacts clean and replace corroded parts.
Always follow the safety information.
Any usage other than described above is not permitted and can
damage the product and lead to associated risks such as shortcircuit, fire, electric shock, etc. You are not allowed to modify
the product.
This product fulfils European and national requirements.
9
Introduction
Introduction
Thank you for selecting a LED luminaire of the L-Series from
ARRI. The L10 is a fresnel-luminaire equipped with a high
precision, micro-processor controlled LED light source. LED
luminaires are much more efficient than light sources with
conventional tungsten lamps. They are a perfect and easy
replacement for conventional fresnel-luminaires with tungsten
lamps.
The L-Series LED luminaires combine the advantages of the
LED technology with the ease of use of a traditional fresnelluminaire. The L10 integrates seamless into established working practice. The optical system offers real fresnel characteristics with an extreme smooth beam and clean shadows. The
half peak angle can be adjusted continuously from 15° - 50°.
The L10 emits white or colored light with adjustable color temperature and adjustable green / magenta saturation. Please
find more detailed information in the section “Specification” on
page 47. The light spectrum is optimized for excellent color
rendition and fulfills perfect the demands of modern, digital
cameras. All models of the L10 can be controlled using the
common DMX512-A protocol or the fixture menu.
The L10 can be powered by AC power. Please find more detailed information in the section “Power” on page 17.
10
Features
Focus
Traditional fresnel-luminaires are able to spot and flood the
beam as needed. Whether it is a flood field for a pullback or a
tight spot for a bright highlight, the continuous focusability of
the L10 performs just as expected.
Versatile beam characteristics
The L10 provides the same ability as conventional fresnel-luminaires to cut set elements and shape the beam with barndoors
and flags.
Even light field
Clean, defined shadows have traditionally been a trait of single
source tungsten and daylight fixtures. L10 fresnel-luminaires
provide the same single shadow properties lighting designers
expect, delivering natural results.
Vibrant colors, full spectrum lighting
True-to-life color rendition is an outstanding feature of the
L10, comparable to a full spectrum tungsten source. The fully
tuneable white light of the L10-C can be adjusted for different
skin tones, camera sensors and mixed light environments. Full
gamut color mixing enables the rendition of all color shades,
making color filters dispensible.
Cool light beam
Like all LED light sources the L10 does emit nearly no infrared
or UV radiation and thus does not forward heat, making actors
feel comfortable in the light beam.
Focus knob
The TRUE BLUE® style focus knobs provide precise adjustment and rapid flood-to-spot with only a few turns. Knobs on
both sides of the fixture ensure easy access from all positions.
Sliding stirrup
The sliding stirrup design enables precise compensation for
front end accessories.
Yoke
With an extreme slim profile, the extruded aluminum yoke provides high strength without added weight. An optional, pole
operated yoke allows full operation of pan and tilt from the floor
and is therefore a popular choice for many studios.
Tilt-lock
The high strength tilt-lock provides extreme secure locking. It
eliminates movement and slippage and ensures that the light
beam will stay where you put it.
Fixture menu
For location applications the L10 is equipped with a fixture
menu for manual adjustment of intensity, color temperature
and plus/minus green as well as hue and saturation (functions
available depending on type).
Introduction
Properties
Unpacking
The L10 is supplied with:
• Power cable with power plug or bare ends
• Stirrup
• 28 mm spigot (mounted on p.o. stirrups)
• Short instruction
Please refer to the section “Accessories” on page 48 for more
information about optional accessories.
DMX-control
All functions of the L10 are controllable through DMX. The L10
is also fully RDM compatible and is equipped with a feedback
channel for reporting all set parameters including system status.
11
Overview
Overview
Spigot
Stirrup
Tilt lock
Top latch
Latch
Safety catch
Stirrup bracket
Focus knob
Connectors
Front view and back view, manual version
12
Focus knob
Fixture menu
Tilt lock lever
Overview
Tilt
Pan
Back view, p.o. version
Focus
13
Physical Installation
Physical Installation
You need
WARNING! Attach an approved safety-cable to
secure the product against clamp or bracket failure.
Lead the safety-cable through the stirrup and keep it
as short as possible. The safety-cable needs to be
approved at least 10 times the weight of the product
including all accessories mounted at the product.
Secure all accessories mounted at the product with
additional safety-cables to protect them from fall
down and cause injuries and damages.
WARNING! The rigging structure needs to be
approved for at least 10 times the weight of all
devices, equipment and cables installed on it.
CAUTION! Block access below the work area and
work from a stable platform whenever installing, servicing or moving the product or accessories.
IMPORTANT! Do not illuminate the display and the
fresnel-lens by high power light beams from a short
distance. The display and the light engine are damaged by high brightness and heat radiation within
very short time.
14
To adjust the stirrup
• a Torx20 screw driver,
• a 10 mm allen key and
• a torque wrench (37 ft-lbs)
to adjust the stirrup.
On delivery the stirrup is in the basic position (tilted back).
Loosen the Torx20 screws on both sides of the stirrup bracket
slightly and pull the stirrup bracket towards the rear of the product. Loosen the lever of the tilt-lock and tilt the stirrup
upwards.
Slide the stirrup to the point of balance. The point of balance is
dependent on the accessories mounted at the product. Tighten
both Torx20 screws of the stirrup brackets. Do not overtighten
the screws. Tilt the stirrup to the desired position and tighten
the tilt-lock by using the lever. For better leverage, press the
knob on the tilt-lock-lever and turn the lever to the desired position.
To mount the spigot
Place the spigot and the distance plate on the 13 mm hole in
the middle of the stirrup. Insert the allen screw with washer and
spring washer and tighten it with a torque wrench to 37 ft-lbs
torque.
• Be aware of the maximum tilt angle 90° upwards and 90°
downwards.
Ensure that you install all accessories correct when you mount
the product above floor level:
• Top latched locked, safety catch snapped in.
• Set up tripods in a stable position. Tripods need to be approved for the load they need to carry.
• Always observe the additional load of cables and accessories!
Please observe the information given in the „Safety leaflet
ARRI lampheads“ (L5.40731.E), which is available for download on our web site www.arri.com.
Basic features
Pan and tilt
Loose the mounting screw of the tripod or the appropriate fixing
screw of the mounting clamp to pan the L10. Tighten the screw
to avoid unintended movement. Loose the tilt-lock to tilt the L10
to the desired angle. Tighten the tilt-lock-lever to avoid unintended movement.
Basic features
To mount the device
Always observe all safety information listed in section “Physical
Installation” on page 14 when you mount the product and
accessories:
To adjust the beam angle
Turn one of the focus knobs beneath the lens tube to adjust the
beam angle continuously. The entire lens tube moves in and
out. Two mechanisms protect the product from being damaged:
• A predetermined braking point prevents the product from
damage, when the focus knob is turned with too high torque
at either end of the focus range.
• The self-impeding focus gear prevents the lens tube to move
itself in or out when the product is operated in a tilted position.
Use of accessories for beam shaping and light design
You can mount accessories such as a barndoor, filter holder or
scrim on the front side of the L10:
• Firmly press the button at the side of the top latch to open the
top latch.
• Insert the accessory from the upside into the brackets until the
safety catch engages. Slightly tilt the safety catch with your
finger for support.
15
Basic features
• Close the top latch. Make sure that the hook of the top latch
engages into the holding ring of the accessory.
DMX/RDM-interface
The L10 has a DMX/RDM-interface. It has 5-pin XLR connectors for DMX/RDM data input and throughput. Please find more
detailed information to establish a DMX/RDM data-link in section “DMX data link” on page 24.
USB-interface
The L10 a mini-USB connector to upload firmware and set parameters. The USB-interface can be used for service purpose
like download error reports and set certain data. To do so you
need a software tool, the ARRI Lighting Service Manager
ALSM.
Control options
You can set up or control the L10 with the options listed in the
table below:
Option
Control
Configuration
Information
Fixture menu
yes
yes
page 18
DMX
yes
no
page 23
RDM
no
yes
page 29
ALSM
no
yes
page 32
Connector Panel
Download it free of charge from the ARRI web site
www.arri.com.
Please find more detailed information to work with the ALSM in
the user manual of the software. The manual is included in the
download package.
To turn on and use the product
Turn on the power switch or connect the L10 to AC power. The
L10 initializes for some seconds and is ready for operation. The
L10 will operate with the settings made on the fixture menu or
received by DMX. Please observe the following section to use
the L10.
1 Power connector
1
2
3
4
2 DMX input
3 DMX through
4 USB connector
16
WARNING! For protection from electric shock, always
connect the product electrically to ground (earth)
when connected to AC power. The AC mains power
supply must be fitted with a fuse or circuit breaker
and ground-fault (earth-fault) protection.
IMPORTANT! Ensure that persons do not look at the
light emission aperture when the product is connected to AC power. The product can light up suddenly. The high intensity of the product can cause eye
irritation or injury when not respecting the safety distance.
IMPORTANT! Always connect the product direct to
AC power. Do not connect it to a dimmer-system.
Doing so will damage the product.
You can hard-wire the L10 to a building electrical installation.
You can install a power plug that is suitable for the local power
outlets on the power cable. Socket outlets or external power
switches that supply the L10 with power must be located near
the product and easily accessible so that the L10 can easily be
disconnected from power.
The L10 requires a power input cable with a Neutrik®
PowerCON® True1 NAC3FX-W cable connector. Cable
requirements are listed in section “Specification” on page 47.
ARRI offers power cables with PowerCON® cable connectors
and different plugs or bare ends (see “Accessories” on
page 48).
To insert and remove the PowerCON® cable connector
• Line up the raised key of the connector and the keyway of the
input socket. Insert the cable connector without force in the
power input socket.
To insert the cable connector:
AC power
• Turn it a full quarter-turn clockwise.
The L10 has an auto-sensing switch-mode power supply that
automatically adapts to AC power at
90 - 264 V ~, 45 - 65 Hz (nom.).
To remove the cable connector:
Before you connect the L10 to AC power, check that:
Power
Power
• Push the connector lock backwards and turn the cable connector counter-clockwise. Pull the cable connector out of the
power input socket.
• the dimmer knob at the fixture menu is set to 0%, and
• no DMX signal is present at the DMX-input of the L10.
17
Fixture menu
Fixture menu
DATA (2)
The DATA indicator lights blue, when a valid DMX signal
is detected on the DMX-input.
Overview of the fixture menu
4
3
FUNCT (3)
The FUNCT button has two functions:
12
1
5
2
6
• Normal operation: Switches between CCT and HSI
mode (only ARRI L10-C).
• Fixture menu open: Jump UP one menu level.
ENTER (4)
The ENTER button has three functions:
9
7
10
8
11
Features of the fixture menu
Status indicator POWER/STATUS (1):
Color
Indication
Green
Fixture switched on. No error.
Red flashing (0,5s rhythm)
*
Warning fixture over temperature
Red*
Change from red to green
Fixture over temperature
*
Fixture normal temperature
*
Red flashing (0,25s rhythm)
Calibration data not loaded
*Display lights up red when STATUS-LED is lit red
18
• Normal operation: Activate blinking arrow for calling up
MEM1 or MEM2.
• Fixture menu open: OPEN next menu level, or
• Confirm a setting.
+ / [up] (5)
The + / [up] button navigates the menu or increases a value.
Press the button long to activate the fast-run feature.
- / [down](6)
The - / [down] button navigates the menu or decreases a value.
Press the button long to activate the fast-run feature.
INTENSITY (9)
The rotary knob sets the intensity level.
GN / SAT (11)
The rotary knob sets the green/magenta saturation or the color
saturation (SAT, only ARRI L10-C in color mode).
MEMORY 1 and MEMORY 2 (7 and 8)
Activate or store a memory.
During operation the mode and recent values are displayed.
On the first menu level the values for INTENSITY, CCT/HUE
(only ARRI L10-C) and GN/SAT (only ARRI L10-C) can be retrieved via the + / [up]/- / [down] buttons. The menu STATUS,
confirmed with ENTER, calls up the next level which displays
information on faultless operation and the temperature of the
light engine. To retrieve values for operating hours, DMX-version and firmware-version, press ENTER to call up the third
level. The FUNCT button jumps up one menu level.
A detailed overview of the fixture menu is listed in section
“Fixture Menu” on page 26.
To set the operation mode (only L10-C)
Press the FUNCT button to switch from CCT mode to HSI
mode and vice versa.
To set the color temperature and green/magenta
saturation in CCT mode
Set the color temperature continuously with the rotary knob
CCT/HUE. Set the green/magenta saturation continuously with
the rotary knob GN/SAT.
Fixture menu
CCT / HUE (10)
The rotary knob sets the color temperature (CCT) or the hue
(only ARRI L10-C in color mode).
Press the + / [up] or - / [down] button until GRN is displayed left
in the display (e.g. +0.23) to retrieve the currently set green/
magenta value. The color temperature is always displayed
(e.g. 4.150K).
To set the color in HSI mode (only ARRI L10-C)
Set the hue continuously with the rotary knob CCT/HUE. Set
the saturation continuously with the rotary knob GN/SAT.
Press the + / [up] or - / [down] button until SAT is displayed left
in the display (e.g. 45) to retrieve the currently set saturation
value. The hue is always displayed (e.g. 118°).
To set the brightness in both operating modes
Set the brightness in both operating modes continuously with
the rotary knob INTENSITY
Press the + / [up] or - / [down] button until INTENSITY is displayed left in the display (e.g. 24%) to retrieve the currently set
brightness value.
IN CCT mode the L10 generates white light with optimized color rendition. In HSI mode the L10 generates colored light. If saturation is set very low, the L10 generates white light, but not
with optimized color rendition.
19
Fixture menu
To set the fan mode
Set the fan mode using the fixture menu:
• Press the + / [up] or - / [down] button, until SETUP is displayed
left in the display.
• Confirm with the ENTER button. Press the + / [up] or - / [down]
button until FAN is displayed.
• Confirm with the ENTER button. The current fan mode is
displayed.
• Press the + / [up] or - / [down] button to select the fan mode
(see the table below). Confirm the selected mode with the
ENTER button. The fan mode is activated immediately.
• Press the FUNCT button two times to leave the menu.
To set the DMX address
• Press the + / [up] or - / [down] button, until SETUP is displayed
left in the display.
• Confirm with the ENTER button. Press the + / [up] or - / [down]
button until DMX is displayed.
• Confirm with the ENTER button. Press the + / [up] or - / [down]
button until CHAN is displayed.
• Confirm with the ENTER button. The current DMX address is
displayed.
• Press the + / [up] or - / [down] button to select the DMX address. Confirm the selected address with the ENTER button.
The DMX address blinks three times for confirmation.
• Press the FUNCT button to leave the menu.
Fan mode
Description
LOW
Fan operates constantly at low speed (silent)
To set the Signal lost behavior
Set the signal lost behavior:
VARI
The temperature of the light engine controls the
fan speed. The fan starts running at app. 70%
brightness.
• Press the + / [up] or - / [down] button, until SETUP is displayed
left in the display.
HI45
Use this mode for ambient temperatures up to
45° C / 113° F. The fan runs at maximum speed.
The maximum brightness is reduced by app.
15%.
• Confirm with the ENTER button. Press the + / [up] or - / [down]
button until DMX is displayed.
• Confirm with the ENTER button. Press the + / [up] or - / [down]
button until LSIG is displayed.
• Confirm with the ENTER button. The current setting is
displayed.
20
• HOLD: The last received DMX values are used until the L10
is switched off or valid DMX data is received again.
• Press the + / [up] or - / [down] button to select the DMX mode.
Confirm the selected mode with the ENTER button. The DMX
mode blinks three times for confirmation.
• BOUT: The L10 douses to 0% intensity.
• Press the FUNCT button to leave the menu.
• H2MF: The last received DMX values are used for 2 minutes.
After 2 minutes the L10 douses to 0% intensity. When valid
DMX data is received after less than 2 minutes, these data will
be used.
To set the display illumination and status indicators
To switch the display illumination and status indicators on or
off:
• Press the + / [up] or - / [down] button to select the signal lost
behavior. Confirm the selected mode with the ENTER button.
The option blinks three times for confirmation.
• Press the FUNCT button to leave the menu.
To set the DMX mode
Set the DMX mode using the fixture menu:
• Press the + / [up] or - / [down] button, until SETUP is displayed
left in the display.
• Confirm with the ENTER button. Press the + / [up] or - / [down]
button until DMX is displayed.
• Confirm with the ENTER button. Press the + / [up] or - / [down]
button until PROT is displayed.
• Confirm with the ENTER button. The current DMX mode is
displayed.
Fixture menu
The following options are available:
• Press the + / [up] or - / [down] button, until SETUP is displayed
left in the display.
• Confirm with the ENTER button. Press the + / [up] or - / [down]
button until INDC is displayed.
• Confirm with the ENTER button. The current setting is
displayed.
• Press the + / [up] or - / [down] button to select the option ON
or OFF. Confirm the selected mode with the ENTER button.
• Press the FUNCT button to leave the menu.
To read out fixture information
To display fixture information:
Operating hours
• Press the + / [up] or - / [down] button, until STATUS is displayed left in the display.
• Confirm with the ENTER button. Press the + / [up] or - / [down]
button until HOUR is displayed.
21
Fixture menu
• Confirm with the ENTER button. The current operating
hours are displayed (e.g. 501h).
Recent temperature
To display the recent temperature of the light engine:
• Press the FUNCT button to leave the menu.
• Press the + / [up] or - / [down] button, until STATUS is displayed left in the display.
Version of the DMX protocol
To display the version of the DMX protocol:
• Press the + / [up] or - / [down] button, until STATUS is displayed left in the display.
• Confirm with the ENTER button. Press the + / [up] or - / [down]
button until the temperature (e.g. 42,1°) is displayed.
• Press the FUNCT button to leave the menu.
• Confirm with the ENTER button. Press the + / [up] or - / [down]
button until DMXV is displayed.
Error status
To display the error status:
• Confirm with the ENTER button. The current version is
displayed (e.g. 3.1).
• Press the + / [up] or - / [down] button, until STATUS is displayed left in the display.
• Press the FUNCT button to leave the menu.
• Confirm with the ENTER button.
Firmware-version
To display the firmware-version:
• If there is no error, OK will be displayed. Otherwise the error
code is displayed (see “Error messages” on page 33).
• Press the + / [up] or - / [down] button, until STATUS is displayed left in the display.
• Press the FUNCT button to leave the menu.
• Confirm with the ENTER button. Press the + / [up] or - / [down]
button until SW is displayed.
• Confirm with the ENTER button. The current firmware
version is displayed (e.g. 2.0).
Short cuts
The demo mode, setting the DMX address and DMX mode can
be called up via short cuts in the fixture menu:
• Press and hold the ENTER button, until JUMP is displayed in
the display (from every menu).
• Press and hold the FUNCT button to activate the demo mode.
Press the ENTER button again to deactivate the demo mode.
• Press the + / [up] button to set the DMX address.
22
DMX control
The JUMP menu closes 3 sec. after the last key press or after
pressing the ENTER button.
DMX mode
Demo mode
In demo mode the L10 calls up an endless loop with all features
the L10 supports.
• ARRI L10-TT and ARRI L10-DT: Change of the color temperature from warm to cold and vice versa. Set the intensity with
the dimmer knob. Set the speed with the CCT knob from 0100% (60 s - 1 s).
• ARRI L10-C: Call up the color spectrum or change the color
temperature from warm to cold and vice versa. Set the intensity with the dimmer knob. Set the speed with the CCT knob
from 0-100% (60 s - 1 s). The GN knob sets the saturation and
changes between color and color temperature sequence.
With GN at „0“ the color temperature loop is active. Turn the
GN knob clockwise to increase the saturation to 100%.
• Press the JUMP and FUNCT button or the FUNCT button
alone to deactivate the demo mode.
As an alternative activate and deactivate the demo mode in the
menu Setup -> DEMO.
Shift key
This short cut is only available in the main menu. Press the
ENTER button, until a small arrow starts blinking in the display.
Memory 1 or memory 2 calls up one of two factory settings.
DMX control
• Press the - / [down] button to set the DMX mode.
The L10 offers, depending on the model, up to 15 DMX modes.
Use the 8 bit modes with basic DMX controllers like dimmer
consoles. The most common modes for operation via DMX are
mode 1 and mode 2.
ARRI recommends the use of the 16 bit modes in combination
with DMX controllers supporting 16 bit resolution to obtain best
results. The high resolution provides smooth dimming and precise color adjustments.
The coarse/fine modes utilize two DMX channels for most parameters and provide higher resolution compared to the 8 bit
modes in combination with DMX controllers that do not support
16 bit resolution. One channel sets the coarse value of the
function which is divided in 256 increments using the fine channel.
The setting can be changed any time using the rotary knobs of
the fixture menu.
White and RGBW
This mode provides control of intensity, color temperature, +/green and individual channels for controlling the red, green,
blue and white color.
23
DMX data link
White
Simple white-only mode. It is used when the number of available channels of the DMX controller is very limited. It provides
control of intensity, color temperature and +/- green.
DMX data link
White & HSI
Provides control of intensity, color temperature, +/- green, hue
and saturation (HSI = hue, saturation, intensity). In HSI mode
the color and intensity is very even over the fixtures as it is controlled using color algorithms which take the tolerances of the
light engines into account during calculation.
The ARRI L10 has 5-pin locking XLR sockets for DMX and
RDM data input and output. The default pin-out of both sockets
is:
RGBW
Simple mode for controlling the overall intensity and the red,
green, blue and white intensity when only a limited number of
DMX channels is available.
Pins 4 and 5 are not used by the ARRI L10 but are bridged between input and output sockets. These pins can therefore be
used as a pass-through connection for an additional data signal if required.
HSI
Simple mode for controlling hue, saturation and intensity when
only a limited number of DMX channels is available.
Pin 4 = Data - (cold)
Pin 5 = Data + (hot).
Please find a detailed description of all modes in chapter
“DMX protocol” on page 34.
Note: Depending on the selected DMX mode the channels required for each product should be allocated in the DMX controller to provide independent control of all products connected to
the controller. Please allocate the maximum number of channels, which is 18 in DMX mode 6.
For controlling the ARRI L10 via DMX you need a DMX data
link.
Pin 1 = Shield
Pin 2 = Data - (cold)
Pin 3 = Data + (hot).
The limitation of 32 products per data link is not applicable for
the L10. You must not connect more than 256 products per
data link. Depending on the channel requirements the address
space of a data link (512 channels) may not be enough to control all products connected. You may set more than one product
to identical DMX addresses to obtain identical behavior. For independent control every product needs to be assigned an individual address range.
If you need to control more products individual, you need to set
up additional DMX data links.
24
• Use shielded twisted-pair cable designed for RS-485 devices
or CAT 6 network cables: standard microphone cable cannot
transmit control data reliably over long runs. 24 AWG cable is
suitable for runs up to 300 meters (1000 ft.). Heavier gauge
cable and/or an amplifier is recommended for longer runs.
DMX data link
Tips for a reliable data transmission
• To split the data link, use a DMX splitter. Use an RDM compatible splitter when you use the RDM functionality.
• Install a DMX termination plug on the last product of every
DMX data link. Terminate the DMX data link on both ends,
when you use the RDM functionality. Ask your system specialist for details.
To connect the data link
• Connect the DMX data output from the controller to the data
input (male XLR) of the L10.
• Run the data link from the data output (female XLR) to the
data input of the next product.
• Terminate the data link by connecting a 120 Ohm, 0.25 Watt
resistor between the data 1 hot (+) and cold (-) conductors
(and between data 2 hot and cold if used) at the data output
of the last product on the link.
25
Fixture Menu
Fixture Menu
From firmware-version 1.0
Note: The small, horizontal arrow in the displays indicates sub-menus. Press the ENTER button to access the sub-menus.
Level 1
26
Level 2
Level 3
Level 4
Description (Default = bold)
Intensity
Displays the recent intensity level when turning the
dimmer knob in %.
CCT
Only in CCT mode:
Displays the recent color temperature when turning
the CCT/HUE knob in K
HUE
Only in HUE mode (only L10-C):
Displays the recent hue when turning the CCT/HUE
knob in ° (0-360°)
GRN
Only in CCT mode:
Displays the recent green / magenta value when turning the GRN/SAT knob in %
SAT
Only in HUE mode (only L10-C):
Displays the recent saturation when turning the
GRN/SAT knob in %
From firmware-version 1.0
Note: The small, horizontal arrow in the displays indicates sub-menus. Press the ENTER button to access the sub-menus.
Note: In setup and status mode the options keep available until another function is called up. All other modes return to the
appropriate mode after 2 sec.
Level 1
Level 2
Level 3
OK
STATUS
Level 4
Description
ERROR
Product ready for operation, no errors OR
Error message (see “Error messages” on page 33)
SW
Firmware version
DMX V
X.X
Version of the DMX protocol
HOUR
XXXX t
Hours of operation
XX.X°C
Fixture Menu
Status Messages
Recent temperature of the light engine
27
Fixture Menu
Fixture Menu
From firmware-version 1.0
Note: The small, horizontal arrow in the displays indicates sub-menus. Press the ENTER button to access the sub-menus.
Note: In setup and status mode the options keep available until another function is called up. All other modes return to the
appropriate mode after 2 sec.
Level 1
Level 2
DMX
Level 3
Level 4
Description (Default setting = bold)
PROT
P.001...P.015
Set the DMX mode
HOLD
The DMX values are held when DMX signal is lost
BOUT
Product douses when DMX signal is lost
H2MF
Product douses 2 min after DMX signal is lost
1...512[-Mode]
Set the DMX start address. Max. start address = 512 channels used by the DMX mode chosen
LSIG
CHAN
FACT
SETUP
DEMO
NO
Do not load the factory defaults
YES
Load the factory defaults
ON
Activate the demo sequence (see page 23)
OFF
De-activate the demo sequence
ON
The status indicators and the illumination of the display stay ON
OFF
The status indicators and the illumination of the display
switch OFF
LOW
Fan mode LOW
VARI
Fan mode VARI
HI45
Fan mode HI45
INDC
FAN
28
From Firmware-version 1.0
Command
Description
GET
SET
Discover Unique Branch
Searches RDM device
X
X
Discover Mute
Mutes the RDM device, no response messages
X
X
Discover Unmute
Activates device for response messages
X
X
Supported Parameters
Shows a list of all supported RDM commands
X
Parameter Description
Shows a list of commands that are not standard rdm commands, mostly commands
from manufacturer. Describes the data type and shows if Set or Get or both are supported for the listed commands.
X
Device Info
Lists RDM protocol version, device model ID, product category, software version ID
(from Main), DMX footprint, DMX personality, sub-device count and sender count.
X
Software Version Label
Shows the software version string from main, e.g. Main 1.66.1 Yes 16 2012 19:10:26
X
DMX Start Address
DMX address
X
X
Identify Service
Identify Flag -> physically fl ash the light, ARRI L10-C flashes Blue and all other
White
X
X
RDM commands
RDM commands
29
RDM commands
30
Required RDM command extensions
Command
Description
GET
Status Message
Display of actual warning / error message of the fixture.
X
Status ID Description
Detailed description of each warning / status report.
X
Device Label
This parameter allows you to generate an informative label for each fixture. It can be
utilized to identify the rack number of a dimmer or to determine the position of a fixture
X
Product Detail ID List
This parameter is utilized to retrieve technical details of a fixture. ARRI L10 shows
LED with PWM control
X
Device Model Description
A text description of up to 32 characters for the model type of the fixture. ARRI L10C, ARRI L10 Daylight Tuneable or ARRI L10 Tungsten Tuneable
X
Manufacturer Label
Display the company name ARRI Lighting
X
Boot Software Version ID
PrBo SW Version e.g. „2.03.00“
X
Boot Software Version Label
Shows text from PrBo Bootloader, e.g. PrBo 2.03.00 Jan 16 2012 19:10:26
X
DMX Personality
DMX mode
X
DMX Personality Description
Displays a text description of a DMX mode with up to 32 characters, shown exactly
as in the description in the ALSM
X
Slot Info
Shows a description for each DMX channel in use in the requested DMX mode
X
Slot Description
Shows a text description with max. 32 characters for each DMX channel from the
requested DMX mode
X
Default Slot Value
Shows the default DMX channel value from the requested DMX mode
X
Sensor Definition
Shows the definition from a specific sensor and a text description
X
Sensor Value
Shows the actual sensor value
X
Device Hours
Shows the actual device hours of the fixture
X
SET
X
X
Description
GET
Lamp Hours
Shows the actual lamp hours of the fixture
X
Factory Defaults
This command deletes all user parameters and sets the fixture to factory default
X
SET
X
Device Power Cycles
Shows the power cycle value, counts every cold start (switch or power-up)
X
Reset Device
Fixture makes a software reset (warm start) and carries out a reboot
X
X
Power State
Power state of the fixture, supported power states:
POWER_STATE_STANDBY (0x02),
POWER_STATE_NORMAL (0xFF),
POWER_STATE_FULL_OFF (0x00)
POWER_STATE_SHUTDOWN (0x01)
X
X
Perform Selftest
Supported test modes and demo modes
X
X
Self Test Description
Shows a description for each test / demo mode
X
RDM commands
Command
31
ARRI Lighting Service Manager
Manufacturer commands
Command
RDM Fan Mode
PID: 0x8001
RDM Status LED
PID: 0x8002
Description
GET
SET
Changes the FAN mode of the fixture
- this message supports Set and Get commands
- the first data byte is used to show / change the fan mode
USER_FAN_MODE_LOW = 1
USER_FAN_MODE_VARI = 2
USER_FAN_MODE_HI45 = 3
X
X
Switch on /off indication LEDs and LCD back light
- this message supports Set and Get commands
- the first data byte is used to switch indication LEDs on and off
LEDs and LCD back light on = 0
LEDs and LCD back light off = 1
X
X
If the DMX signal gets lost or the DMX device is unplugged the LED fixture holds the
last valid signal, or it holds the last valid signal for two minutes and then douses or
switches off immediately.
Supported values:
0 -> hold
1 -> hold 2 minutes
3 -> switch off
X
X
Supported values from -1 to +1
RDM DMX Signal Lost Mode
PIS: 0x8005
ARRI Lighting Service Manager
Please find information about the features and the functionality of the ARRI Lighting Service Manager in the user manual for the
ARRI Lighting Service Manager, which can be downloaded with the ARRI Lighting Service Manager software-bundle from the
ARRI web site www.arri.com free of charge.
32
From firmware-version 1.0
Code
Error
Remedy
E.003
Controller over temperature.
STATUS lit up red.
Let the product cool down. The STATUS indicator changes to green when the product has
cooled down. Turn the dimmer knob to „0“ or send an intensity value „0“ via DMX to activate the light engine again.
E.004
Light engine over temperature
See E.003
E.005
Power supply over temperature
See E.003
E.006
Calibration data of light engine
faulty or EEPROM error.
WARNING: Loss of calibration data. This error can only be fixed by re-calibrating the light
engine. Please contact the ARRI service.
E.007
Invalid PWM value calculation
Notice: The product can be used on. This message is more a notification than an error.
E.008
Invalid values during calculation
See E.007
E.009
Invalid values during calculation
See E.007
E.010
Fan error. The fan speed deviates or the fan doesn’t run at all.
Set the fan to LOW or HI and see if it starts rotating, in order to determine if there is an
electrical malfunction.
All mechanical tests or repairs may only be carried out by a trained service technician.
E.011
Fixture menu module not be
detected.
If the fixture menu is working, error E.011 can be ignored. However, if the fixture menu
remains dark (no LED lights up) we recommend to contact the ARRI service. They can
then carry out detailed analyses.
E.012
Temperature sensor(s) are
defective or deviation within
NTC values too high.
One or more temperature sensors are defective or the deviation within the individual NTCs
or BNTCs exceeds the variation tolerance of 12° C / 54° F. Check the error log (LSeries
Manager) to see which temperature sensors are affected. Contact the ARRI service.
E.013
Calibration data faulty.
WARNING: Loss of calibration data. Fixture needs to be re-calibrated.
E.014
Watchdog error
Notice: The product can be used on. This message is more a notification than an error.
E.015
LED channel faulty
Notice: The product can be used on. This message is more a notification than an error.
Error messages
Error messages
33
DMX protocol
DMX protocol
Mode 1: 8 bit resolution per function
DMX protocol V3.x is set as default. Use the ALSM to change
to DMX protocol V4.x. ARRI advises to reserve 4 DMX channels more for each fixture when using DMX protocol V3.x. This
way you do not need to modify the patch when you want to use
additional features which will become available with DMX protocol V4.x.
The DMX protocol V4.x uses 4 DMX channels more in each
DMX mode.
Channel
1
2
3
ARRI L10-TT (Tungsten Tuneable)
Percent
Function
0-255
0-100
Dimmer
closed → open
0-255
0-100
Color temperature CCT
2.600 K → 3.600 K
0-10
11-20
21-119
120-145
146-244
245-255
0-4
5-8
8-46
47-57
57-96
96-100
GN saturation
neutral / no effect
full minus green
-99% → -1%
neutral / no effect
1% → 99%
full plus green
From firmware-version 1.0
4
Reserved (only V4.x)
Overview
5
Reserved (only V4.x)
6
Reserved (only V4.x)
7
Reserved (only V4.x)
*
8 bit, 1 channel
per function
16 bit, 2 cannels
per function
Coarse / fine, 1-2
channels per function
DMX mode 1*
DMX mode 2
DMX mode 3
= Factory default
GN saturation
The value describes the shift from the neutral point to full minus
green or full plus green in percent.
(Reference: Rosco Cinegel #3304 and #3308)
34
Value
Channel
1
HI
2
LO
3
HI
4
LO
HI
5
6
LO
Value
Percent
Function
0-100
Dimmer
closed → open
0-65535
0-100
Color temperature
2.600 K → 3.600 K
0-5.000
5.001-10.000
10.001-29.999
30.000-40.000
40.001-59.999
60.000-65.535
0-7
8-15
16-46
46-61
61-92
92-100
GN saturation
neutral / no effect
full minus green
-99% → -1%
neutral / no effect
1% → 99%
full plus green
0-65535
Mode 3: Coarse / fine channel per function
Each of the 256 coarse steps is divided in 256 fine steps. Use
this mode when your lighting control desk does not support true
16 bit resolution.
Channel
7
Reserved (only V4.x)
8
Reserved (only V4.x)
9
Reserved (only V4.x)
10
Reserved (only V4.x)
1
2
3
4
5
Value
Percent
Function
0-255
0-100
Dimmer coarse
closed → open
0-255
0-100
Dimmer fine
0-255
0-100
0-255
0-100
Color temperature fine
0-4
5-8
8-46
47-57
57-96
96-100
GN saturation
neutral / no effect
full minus green
-99% → -1%
neutral / no effect
1% → 99%
full plus green
0-10
11-20
21-119
120-145
146-244
245-255
DMX protocol
Mode 2: 16 bit resolution per function
Color temperature
coarse
2.600 K → 3.600 K
6
Reserved (only V4.x)
7
Reserved (only V4.x)
8
Reserved (only V4.x)
9
Reserved (only V4.x)
35
DMX protocol
ARRI L10-DT (Daylight Tuneable)
From firmware-version 1.0
Channel
Overview
*
1
8 bit, 1 channel
per function
16 bit, 2 channels
per function
Coarse / fine, 2 channels per function
DMX mode 1*
DMX mode 2
DMX mode 3
= Factory default
GN saturation
The value describes the shift from the neutral point to full minus
green or full plus green in percent.
(Reference: Rosco Cinegel #3304 and #3308)
36
Mode 1: 8 bit resolution per function
2
3
Value
Percent
Function
0-255
0-100
Dimmer
closed → open
0-255
0-100
Color temperature CCT
5.000 K → 6.500 K
0-10
11-20
21-119
120-145
146-244
245-255
0-4
5-8
8-46
47-57
57-96
96-100
GN saturation
neutral / no effect
full minus green
-99% → -1%
neutral / no effect
1% → 99%
full plus green
4
Reserved (only V4.x)
5
Reserved (only V4.x)
6
Reserved (only V4.x)
7
Reserved (only V4.x)
Channel
Value
Percent
1
HI
2
LO
3
HI
4
LO
0-65535
0-100
5
HI
0-5.000
5.001-10.000
10.001-29.999
30.000-40.000
40.001-59.999
60.000-65.535
0-7
8-15
16-46
46-61
61-92
92-100
6
LO
0-65535
0-100
Function
Dimmer
closed → open
Mode 3: Coarse / fine channel per function
Each of the 256 coarse steps is divided in 256 fine steps. Use
this mode when your lighting control desk does not support true
16 bit resolution.
Channel
Color temperature CCT
5.000 K → 6.500 K
GN saturation
neutral / no effect
full minus green
-99% → -1%
neutral / no effect
1% → 99%
full plus green
1
2
3
4
Reserved (only V4.x)
Reserved (only V4.x)
Reserved (only V4.x)
Reserved (only V4.x)
5
Value
Percent
Function
0-255
0-100
Dimmer coarse
closed → open
0-255
0-100
Dimmer fine
0-255
0-100
0-255
0-100
Color temperature fine
0-4
5-8
8-46
47-57
57-96
96-100
GN saturation
neutral / no effect
full minus green
-99% → -1%
neutral / no effect
1% → 99%
full plus green
0-10
11-20
21-119
120-145
146-244
245-255
DMX protocol
Mode 2: 16 bit resolution per function
Color temperature
coarse
5.000 K → 6.500 K
Reserved (only V4.x)
Reserved (only V4.x)
Reserved (only V4.x)
Reserved (only V4.x)
37
DMX protocol
ARRI L10-C
Mode 1: White & RGBW, 8 bit resolution per function
From firmware-version 1.0
Channel
Overview
1
8 bit, 1 channel
per function
16 bit, 2 cannels
per function
Coarse/fine, 1-2 channels per function
DMX mode 1*
White & RGBW
DMX mode 6
White & RGBW
DMX mode 11
White & RGBW
DMX mode 2
White
DMX mode 7
White
DMX mode 12
White
DMX mode 3
White & HSI
DMX mode 8
White & HSI
DMX mode 13
White & HSI
DMX mode 4
RGBW
DMX mode 9
RGBW
DMX mode 14
RGBW
4
DMX mode 5
HSI
DMX mode 10
HSI
DMX mode 15
HSI
5
2
3
6
*
= Factory default
GN saturation
The value describes the shift from the neutral point to full minus
green or full plus green in percent.
(Reference: Rosco Cinegel #3304 and #3308)
38
7
8
Value
Percent
Function
0-255
0-100
Dimmer
closed → open
0-255
0-100
Color temperature CCT
2.800 K → 10.000 K
0-10
11-20
21-119
120-145
146-244
245-255
0-4
5-8
8-46
47-57
57-96
96-100
GN saturation
neutral / no effect
full minus green
-99% → -1%
neutral / no effect
1% → 99%
full plus green
0-255
0-100
Xfade to color
White → RGBW color
0-255
0-100
Intensity red
0% → 100%
0-255
0-100
Intensity green
0% → 100%
0-255
0-100
Intensity blue
0% → 100%
0-255
0-100
Intensity white
0% → 100%
9
Reserved (only V4.x)
10
Reserved (only V4.x)
11
Reserved (only V4.x)
12
Reserved (only V4.x)
Channel
1
2
3
4
Function
Mode 3: White & HSI, 8 bit resolution per function
Value
Percent
0-255
0-100
Dimmer
closed → open
1
0-255
0-100
Color temperature CCT
2.800 K → 10.000 K
2
0-10
11-20
21-119
120-145
146-244
245-255
0-4
5-8
8-46
47-57
57-96
96-100
GN saturation
neutral / no effect
full minus green
-99% → -1%
neutral / no effect
1% → 99%
full plus green
Reserved (only V4.x)
5
Reserved (only V4.x)
6
Reserved (only V4.x)
7
Reserved (only V4.x)
Channel
3
4
5
6
Value
Percent
Function
0-255
0-100
Dimmer
closed → open
0-255
0-100
Color temperature CCT
2.800 K → 10.000 K
0-10
11-20
21-119
120-145
146-244
245-255
0-4
5-8
8-46
47-57
57-96
96-100
0-255
0-100
Xfade to color
White → RGBW color
0-255
0-100
Hue
0° → 360°
0-255
0-100
Saturation
0 → full saturated
DMX protocol
Mode 2: White, 8 bit resolution per function
GN saturation
neutral / no effect
full minus green
-99% → -1%
neutral / no effect
1% → 99%
full plus green
7
Reserved (only V4.x)
8
Reserved (only V4.x)
9
Reserved (only V4.x)
10
Reserved (only V4.x)
39
DMX protocol
Mode 4: RGBW, 8 bit resolution per function
Channel
1
2
3
Percent
Function
Channel
0-255
0-100
Dimmer
closed → open
0-255
0-100
Intensity red
0% → 100%
2
0-255
0-100
Intensity green
0% → 100%
3
0-255
0-100
Intensity blue
0% → 100%
0-100
1
Value
Percent
Function
0-255
0-100
Dimmer
closed → open
0-255
0-100
Hue
0° → 360°
0-255
0-100
Saturation
0 → full saturated
4
Reserved (only V4.x)
5
Reserved (only V4.x)
Intensity white
0% → 100%
6
Reserved (only V4.x)
6
Reserved (only V4.x)
7
Reserved (only V4.x)
7
Reserved (only V4.x)
8
Reserved (only V4.x)
9
Reserved (only V4.x)
4
5
40
Value
Mode 5: HSI, 8 bit resolution per function
0-255
Channel
Value
Percent
Function
Mode 7: White, 16 bit resolution per function
Channel
1
HI
2
LO
0-65535
0-100
Dimmer
closed → open
HI
HI
0-5.000
5.001-10.000
10.001-29.999
30.000-40.000
40.001-59.999
60.000-65.535
0-7
8-15
16-46
46-61
61-92
92-100
GN saturation
neutral / no effect
full minus green
-99% → -1%
neutral / no effect
1% → 99%
full plus green
3
3
4
0-65.535
0-100
0-65.535
0-100
4
LO
5
HI
6
LO
7
HI
8
LO
9
HI
10
LO
11
HI
12
LO
13
HI
14
LO
1
HI
2
LO
Value
Percent
Function
0-65535
0-100
Dimmer
closed → open
LO
0-65.535
0-100
Color temperature CCT
2.800 K → 10.000 K
5
HI
Xfade to color
White → RGBW color
6
LO
0-5.000
5.001-10.000
10.001-29.999
30.000-40.000
40.001-59.999
60.000-65.535
0-7
8-15
16-46
46-61
61-92
92-100
GN saturation
neutral / no effect
full minus green
-99% → -1%
neutral / no effect
1% → 99%
full plus green
Intensity red
0% → 100%
7
Reserved (only V4.x)
8
Reserved (only V4.x)
9
Reserved (only V4.x)
10
Reserved (only V4.x)
0-65.535
0-100
Intensity green
0% → 100%
0-65.535
0-100
Intensity blue
0% → 100%
0-65.535
0-100
Intensity white
0% → 100%
15
Reserved (only V4.x)
16
Reserved (only V4.x)
17
Reserved (only V4.x)
18
Reserved (only V4.x)
DMX protocol
Mode 6: White & RGBW, 16 bit resolution per function
41
DMX protocol
42
Mode 8: White & HSI, 16 bit resolution per function
Channel
1
HI
2
LO
Value
Percent
Function
0-65535
0-100
Dimmer
closed → open
Mode 9: RGBW, 16 bit resolution per function
Channel
1
HI
2
LO
Value
Percent
Function
0-65535
0-100
Dimmer
closed → open
0-65.535
0-100
Intensity red
0% → 100%
0-65.535
0-100
Intensity green
0% → 100%
0-65.535
0-100
Intensity blue
0% → 100%
0-65.535
0-100
Intensity white
0% → 100%
3
HI
HI
LO
0-65.535
0-100
Color temperature CCT
2.800 K → 10.000 K
3
4
4
LO
HI
HI
LO
LO
0-7
8-15
16-46
46-61
61-92
92-100
6
6
0-5.000
5.001-10.000
10.001-29.999
30.000-40.000
40.001-59.999
60.000-65.535
GN saturation
neutral / no effect
full minus green
-99% → -1%
neutral / no effect
1% → 99%
full plus green
5
5
7
HI
8
LO
0-100
Xfade to color
White → RGBW color
11
Reserved (only V4.x)
9
HI
12
Reserved (only V4.x)
10
LO
0-100
Hue
0° → 360°
13
Reserved (only V4.x)
11
HI
14
Reserved (only V4.x)
12
LO
0-65.535
0-65.535
0-65.535
0-100
Saturation
0 → full saturated
13
Reserved (only V4.x)
14
Reserved (only V4.x)
15
Reserved (only V4.x)
16
Reserved (only V4.x)
7
HI
8
LO
9
HI
10
LO
Channel
1
HI
2
LO
3
HI
4
LO
5
HI
6
LO
Value
Percent
Channel
Function
0-65535
0-100
Dimmer
closed → open
0-65.535
0-100
Hue
0° → 360°
0-100
Saturation
0 → full saturated
5
6
0-65.535
7
7
Reserved (only V4.x)
8
Reserved (only V4.x)
9
Reserved (only V4.x)
9
10
Reserved (only V4.x)
10
Mode 11: White & RGBW, Coarse/fine per function
Channel
1
2
Value
Percent
0-255
0-100
Dimmer coarse
closed → open
0-255
0-100
Dimmer fine
0-255
0-100
Color temperature CCT
coarse
2.800 K → 10.000 K
0-255
0-100
Color temperature fine
3
4
Function
8
11
12
13
14
Value
Percent
Function
0-10
11-20
21-119
120-145
146-244
245-255
0-4
5-8
8-46
47-57
57-96
96-100
GN saturation
neutral / no effect
full minus green
-99% → -1%
neutral / no effect
1% → 99%
full plus green
0-255
0-100
Xfade to color
White → RGBW color
0-255
0-100
Intensity red coarse
0% → 100%
0-255
0-100
Red fine
0-255
0-100
Intensity green coarse
0% → 100%
0-255
0-100
Green fine
0-255
0-100
Intensity blue coarse
0% → 100%
0-255
0-100
Blue fine
0-255
0-100
Intensity white coarse
0% → 100%
0-255
0-100
White fine
15
Reserved (only V4.x)
16
Reserved (only V4.x)
17
Reserved (only V4.x)
18
Reserved (only V4.x)
DMX protocol
Mode 10: HSI, 16 bit resolution per function
43
DMX protocol
Mode 12: White, Coarse / fine channel per function
Channel
1
2
Value
Percent
5
6
Channel
0-255
0-100
Dimmer coarse
closed → open
0-255
0-100
Dimmer fine
2
3
0-255
0-100
Color temperature CCT
coarse
2.800 K → 10.000 K
0-255
0-100
Color temperature fine
4
0-4
5-8
8-46
47-57
57-96
96-100
GN saturation
neutral / no effect
full minus green
-99% → -1%
neutral / no effect
1% → 99%
full plus green
3
4
Function
Mode 13: White & HSI, Coarse / fine channel per function
0-10
11-20
21-119
120-145
146-244
245-255
Reserved (only V4.x)
1
5
6
7
Reserved (only V4.x)
8
Reserved (only V4.x)
7
9
Reserved (only V4.x)
8
9
10
44
Value
Percent
Function
0-255
0-100
Dimmer coarse
closed → open
0-255
0-100
Dimmer fine
0-255
0-100
Color temperature CCT
coarse
2.800 K → 10.000 K
0-255
0-100
Color temperature fine
0-10
11-20
21-119
120-145
146-244
245-255
0-4
5-8
8-46
47-57
57-96
96-100
GN saturation
neutral / no effect
full minus green
-99% → -1%
neutral / no effect
1% → 99%
full plus green
0-255
0-100
Xfade to color
White → RGBW color
0-255
0-100
Hue coarse
0 → 360°
0-255
0-100
Hue fine
0-255
0-100
Saturation coarse
0 → full saturated
0-255
0-100
Saturation fine
11
Reserved (only V4.x)
12
Reserved (only V4.x)
13
Reserved (only V4.x)
14
Reserved (only V4.x)
Channel
1
2
3
4
5
6
7
8
9
10
Value
Percent
Function
Mode 15: HSI, Coarse / fine channel per function
Channel
Value
Percent
Function
0-255
0-100
Dimmer coarse
closed → open
0-255
0-100
Dimmer fine
2
0-255
0-100
Intensity red coarse
0% → 100%
3
0-255
0-100
Red fine
4
0-255
0-100
Intensity green coarse
0% → 100%
5
0-255
0-100
Green fine
6
Reserved (only V4.x)
0-100
Intensity blue coarse
0% → 100%
7
0-255
8
Reserved (only V4.x)
0-255
0-100
Blue fine
9
Reserved (only V4.x)
0-255
0-100
Intensity white coarse
0% → 100%
10
Reserved (only V4.x)
0-255
0-100
White fine
11
Reserved (only V4.x)
12
Reserved (only V4.x)
13
Reserved (only V4.x)
14
Reserved (only V4.x)
1
0-255
0-100
Dimmer coarse
closed → open
0-255
0-100
Dimmer fine
0-255
0-100
Hue coarse
0 → 360°
0-255
0-100
Hue fine
0-255
0-100
Saturation coarse
0 → full saturated
0-255
0-100
Saturation fine
DMX protocol
Mode 14: RGBW, Coarse / fine channel per function
45
DMX protocol
Overview of typical CCT values as DMX values
CCTValue
DMX-Value (8 bit)
CCT values for the ARRI L10 models:
DMX-Value (16 bit)
CCTmax = 3.600 K
L10-
TT
DT
C
TT
DT
C
3.200 K
153
--
14
39.321
--
3.670
5.600 K
--
102
99
--
26.214
25.493
L10-DT (Daylight Tuneable)
CCTmin = 5.000 K
6.000 K
--
170
113
--
43.712
29.098
CCTmax = 6.500 K
6.500 K
--
100%
131
--
65.535
33.685
L10-C
CCTmin = 2.800 K
To calculate CCT values in DMX % and vice versa
Use the following formulas to transform CCT values in DMX %
values and vice versa:
( CCT max – CCT min ) × DMX in percent
CCT Target = ----------------------------------------------------------------------------------------× CCT min
100
CCT recent – CCT minDMX in percent = -----------------------------------------------× 100
CCT max – CCT min
46
L10-TT (Tungsten Tuneable)
CCTmin = 2.600 K
CCTmax = 10.000 K
Physical
Length (Focus in flood position) . . . . . . . . . . . . . . . 560 mm (22 in.)
Length (Focus in spot position) . . . . . . . . . . . . . 745 mm (29.3 in.)
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 502 mm (19.8 in.)
Height . . . . . . . . . . . . . . . . . 395 mm (15.5 in., Stirrup folded down)
Latch distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344 mm / 13.5 “
Width for accessories . . . . . . . . . . . . . . . . . . . . . . . 344 mm / 13.5 “
Weight (manual version, w/o accessories) . . . . . 19,7 kg (43.4 lbs.)
Weight (P.O. version, w/o accessories) . . . . . . . . .21,3 kg (47 lbs.)
Light source
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ARRI LED Lightengine
Typ. LED lifetime L70 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50.000 h
White light. . . . . . . . . . . . . . . . . . 2.800 K - 10.000 K (ARRI L10-C)
. . . . . . . . . . . . . . . . . . . . . . . . . . 2.600 K - 3.600 K (ARRI L10-TT)
. . . . . . . . . . . . . . . . . . . . . . . . . . 5.000 K - 6.500 K (ARRI L10-DT)
Colored light . . . . . . . . . . . .RGBW color mixing (only ARRI L10-C)
Color rendering index . . . . . . . . . . . . . . . . . . . . . . . . . typ. CRI >94
Green/Magenta saturation . . . . . . +/- 1 (full green to full magenta)
Optical path
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fresnel, focussable
Lens diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 mm / 10 “
Half peak angle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15° - 50°
Dynamic functions
Dimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .electronic, 0 - 100%
Color mixing . . . . . . . . . . . . . . . . . . . . . . . . . . . RGBW color mixing
. . . . . . . . . . . . . . . . . . . . . . .(Hue and saturation, only ARRI L10-C)
Specification
Specification
Control and Programming
DMX channels . . . . . 7-18 channels, depending on type and mode
Setting and addressing. . . . . . . . . . . . . Fixture menu, RDM, ALSM
DMX compliance . . . . . . . . . . . . . . . . . . . . . . . . .ESTA DMX 512A
RDM compliance . . . . . . . . . . . . . . . . . . . . . . . . .ESTA DMX 512A
Firmware update. . . . . . . . . . . . . . . . . . . USB interface and ALSM
Construction
Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Blue/silver or black
Housing . . . . . . . . . . . . . Composite housing with aluminum frame
Protection rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IP 20
Installation
Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 mm spigot
Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +/- 90°
Minimum clearance around fixture . . . . . . . . . . . . . 0,5 m (19.7 in.)
Minimum view distance to light aperture . . . . . . . . 0,5 m (19.7 in.)
Connectors
AC power input . . . . . . . . . . . . . . . . . Neutrik® PowerCON® True1
DMX and RDM data in/out . . . . . . . . 5-pin, locking XLR connector
USB connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mini-USB-A
47
Specification
Electrical
AC power . . . . . . . . . . . . . . . . . . . . . . . 90 - 250 V~, 50 - 60 Hz AC
Power supply . . . . . . . Auto-sensing switching-mode power supply
Typical Power
230 V, 50 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 510 W
cos ϕ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 0.9
Measurements made at nominal voltage with all LEDs at full intensity.
Allow for a deviation of +/- 10%
Noise emission
Ambient temperature = 35° C (95° F). . . . . . . . . . . . . . . < 20dB(A)
Ambient temperature = 45° C (113° F). . . . . . . . . . . . . . < 30dB(A)
Thermal
Minimum ambient temperature (ta). . . . . . . . . . . . . . .-20° C (-4° F)
Maximum ambient temperature (ta) . . . . . . . . . . . . . 45° C (113° F)
Cooling . . . . . . . . . . . . . .Silent, temperature-controlled fan cooling
Approvals
EU safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN / IEC 60598-2-17
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN / IEC 60598-1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN / IEC 62471
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN / IEC 62493
EU EMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN 55015
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN / IEC 61000-3-2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN / IEC 61000-3-3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN / IEC 61547
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CISPR 15
US safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UL1573
48
US EMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FCC CFR 47 Part 2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FCC CFR 47 Part 15
Canada safety . . . . . . . . . . . . . . . . . . . . CAN/CSA C22.2 No. 166
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CAN/CSA C22.2 No. 9.0
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .CAN/CSA C22.2 N0. 9.0S1
Canada EMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ICES-003
Included items
28 mm spigot
Short instruction
Accessories
Power input cable 1,5 m, 3G1,5, H05RN-F, HAR,
PowerCon TRUE1, bare end . . . . . . . . . . . . . . . . . . . . . L2.0001485
Power input cable 3,0 m, 3G1,5, H05RN-F, HAR,
Switch, PowerCon TRUE1, Schuko plug . . . . . . . . . . . . L2.0001486
Power input cable 7,0 m, 3x16AWG, SEOOW, SOOW
or W, cUL (ZJCZ), Switch, PowerCON TRUE1,
Edison plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . L2.0001487
4-leaf barndoor (344 mm, 13.5 “) . . . . . . . . . . . . . . . . . L2.40950.0
4-leaf barndoor (344 mm, 13.5 “, black / silver) . . . . . . L2.80951.0
8-leaf barndoor (344 mm, 13.5 “) . . . . . . . . . . . . . . . . . L2.40960.0
Filter frame (330 mm, 13.0 “) . . . . . . . . . . . . . . . . . . . . L2.80970.0
Snoot with variable aperture (344 mm / 13.5 “) . . . . . . L2.80975.0
Speed ring circular (9305, 344 mm, 13.5 “) . . . . . . . . . L2.76247.0
Chimera Quartz Plus „S“ . . . . . . . . . . . . . . . . . . . . . . . L2.89054.0
Safety-cable with Kettbiner. . . . . . . . . . . . . . . . . . . . . . L2.80864.0
ARRI L10-C, MAN., blue/silver, Edison (7 m). . . . . . . . L0.0003381
ARRI L10-C, MAN., blue/silver, Schuko (3 m) . . . . . . . L0.0003382
ARRI L10-C, MAN., blue/silver, bare ends . . . . . . . . . . L0.0003383
ARRI L10-C, MAN., black, bare ends. . . . . . . . . . . . . . L0.0003384
ARRI L10-C, P.O., blue/silver, bare ends. . . . . . . . . . . L0.0003385
ARRI L10-C, P.O., black, bare ends. . . . . . . . . . . . . . . L0.0003386
ARRI L10-TT, MAN., blue/silver, Edison (7 m). . . . . . . L0.0003387
ARRI L10-TT, MAN., blue/silver, Schuko (3 m) . . . . . . L0.0003388
ARRI L10-TT, MAN., blue/silver, bare ends . . . . . . . . . L0.0003389
ARRI L10-TT, MAN., black, bare ends . . . . . . . . . . . . . L0.0003390
ARRI L10-TT, P.O., blue/silver, bare ends . . . . . . . . . . L0.0003391
ARRI L10-TT, P.O., black, bare ends. . . . . . . . . . . . . . L0.0003392
ARRI L10-DT, MAN., blue/silver, Edison (7 m) . . . . . . L0.0003393
ARRI L10-DT, MAN., blue/silver, Schuko (3 m) . . . . . . L0.0003394
ARRI L10-DT, MAN., blue/silver, bare ends. . . . . . . . . L0.0003395
ARRI L10-DT, MAN., black, bare ends. . . . . . . . . . . . . L0.0003396
ARRI L10-DT, P.O., blue/silver, bare ends. . . . . . . . . . L0.0003397
ARRI L10-DT, P.O., black, bare ends . . . . . . . . . . . . . L0.0003398
Specification subject to change without notice. For the latest
product specification including photometric data, see
www.arri.com
Specification
Order information
In case of technical problems, please visit us at www.arri.com,
to find the next ARRI service center.
www.arri.com
FCC
This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when this equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case the user will be required to correct
the interference at his/her own expense.
49
Download PDF

advertising