installation instructions

INSTALLATION
INSTRUCTIONS
Sapphire basin mixer
with pop up waste
CTA11
Important
● We recommend that this product is installed by a qualified professional contractor. Such as a plumber who is certified by NVQ
(National Vocational Qualification) or SNVQ (Scottish National Vocational Qualification) Level 3.
● Please check this product immediately to ensure that it has not been damaged and is complete. Before installation, please make
sure this product is the correct model and you have all the parts required for installation and using.
● All the taps should be supplied with hot and cold water at balanced pressure. If not, then the mixing function will not work correctly.
It is necessary to fit non-return valves on both hot and cold feeds pipe. These are not supplied.
● Please flush the water system to ensure that no metal swarf, solder, and other impurities can enter the taps.
● Turn off water supply before commencing work, this should be done at the isolating valves of inlet feeds if fitted or main stopcock.
● Please read these instructions carefully and keep it for future reference.
Working pressure
The tap is suitable for both high and low pressure installation. To ensure that the tap works well under low water pressure, the
cold water storage tank must be at least 2 meters above the installed position. The maximum static pressure is 10 bar, and
operating water pressure is 5 bar. Where the operating water pressure above 5 bar, then a pressure reducing valve must be fitted.
Straightener and aerator (alternative option)
Taps are all fitted with a flow straighter for use in low pressure installations.
An aerator is supplied in the box, and is an option that can be used in high
pressure installations. These can be interchanged by unscrewing the part,
and replacing with the alternate one. During the process do not loose the
washer, between the parts.
FLOW STRAIGHTENER
AERATOR
Cleaning
Before use: Unscrew the filter and allow the water to run freely
for 5 minutes. Then screw the filter back in place.
Periodically: Unscrew the nozzle and remove. Rinse it with
running water until any loose debris is cleared.
Then replace the nozzle and tighten.
NOZZLE
Maintenance
We do NOT recommend you use any household cleaners to clean the product. Because these cleaners change substance or formula
too frequently. The product should be always cleaned only with soapy water and rinsed with clean water and dried with a soft cloth.
1-2
C
Cleaning Cartridge
Dimension
HANDLE
Ø45
161.8
ALLEN KEY
CAP
153.8
GRUB SCREW
CARTRIDGE COVER
20
Ø52
90.5
Max. 30
109.8
RETAINING NUT
Ø35
Ø63
CARTRIDGE
MIXER BODY
2-G1/2
To remove the cartridge.
179.1
First shut off the water supply to the tap.
1: Pull out the cap from the handle.
2: Loosen the grub screw in handle, but do not remove it.
3: Take off the handle, unscrew the cartridge cover.
4: Using a correct size spanner unscrew the retaining nut.
5: Pull the cartridge and wash it with clean running water.
6. Dry and lightly grease the seals (only use silicone grease)
7: Replace them in turn.
Installation
HANDLE
MIXER BODY
NOZZLE
DECORATIVE
HEAD
MIXER BASE
O’ RING
PLUG
FIXING NUT
PLUG
ADJUSTMENT
SCREW
POP-UP
CONTROL ROD
PLUG
HOUSING
HORIZONTAL
CONTROL ROD
RUBBER
WASHER
Basin waste
hole
FLEXIBLE PIPES
LEFT: HOT FEED
RIGHT: COLD FEED
RUBBER
WASHER
BALL JOINT
RETAINER
WASHER(1)
BODY
BALL
WASHER(2)
2-2
Install the main body part:
a) Fit the O’ ring into the groove in the underside
of the mixer body.
b) Screw the flexible pipes into the mixer body,
and fully hand tighten.
c) Pass the tail of flexible pipes through the hole
on the basin from above, and place the mixer in
position on the basin, to see if any alteration to
the existing supply pipe work is necessary, make
any necessary alterations to the pipe work.
d) Slide the fixing nut up the tails and onto the fixing
bolt.
e) Check that the mixer body is correctly positioned,
fully tighten the fixing nut.
f) Connect the water supply pipe to the tail of flexible
pipes with the hot water on the left and cold water on
the right.
Install Pop-Up Waste:
a) Remove decorative head on the Pop-up control rod,
Insert the Pop-Up control rod into the mixer body
from underneath the basin, mount the decorative
head and Pop-Up control rod together.
b) Insert the pop up waste on the basin and tighten.
c) Insert the horizontal control rod into the waste,
and tight the ball joint retainer to make sure the
ball with two washers on both sides are fix with
the waste.
d) Connect the pop-up control rob with the horizontal
control rod.
e) Test the pop-up waste function, adjust the connection
between pop-up control rod and horizontal control
rod, or the ball joint retainer if necessary.
C
Download PDF
Similar pages
installation instructions
Franke Polyedro
DTY345 Datasheet
brochure rd3300
installation instructions
Franke Planario
Tesi Single Lever Built
BURPK277 Instalation Guide
installation instructions
BURPK276 Instalation Guide