26” FIREBOX
EN
RU
UA
FR
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2
and EN60555-3. These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
08/53613/2 (EU)
Issue 1
1
2
3
A
B
C
D
E
F
A
G
H
D
C
F
G
H
E
B
4
5
585mm
229mm
6
680mm
7
EN
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
When using electrical appliances, basic
precautions should be followed to
reduce the risk of fire, electric shock, and
injury to persons, including the following:
If the appliance is damaged, check
immediately with the supplier before
installation and operation.
Do not use this appliance in the
immediate surroundings of a bath,
shower or swimming pool.
Do not use outdoors.
This appliance must not be located
immediately above or below a fixed
socket outlet or connection box.
WARNING: The appliance carries
the Warning Symbol indicating that
it must not be covered or has a Do
not cover label. Do not cover or
obstruct in any way the heat outlet
grille located above the flame window
on the appliance Overheating will result
if the appliance is accidentally covered.
Do not place material or garments on the
appliance, or obstruct the air circulation
around the appliance, for instance by
curtains or furniture, as this could cause
overheating and a fire risk.
In the event of a fault unplug the heater.
Unplug the appliance when not required
for long periods. The supply cord must
be placed on the right hand side of
the heater away from the heat outlet
underneath the appliance.
This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe way
and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not
be made by Children without supervision.
Children of less than 3 years should
be kept away unless continuously
supervised. Children aged from 3 years
and less than 8 years shall only switch
on/off the appliance provided that it has
been placed or installed in its intended
normal operating position and they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understanding the hazards
involved. Children aged from 3 years
and less than 8 years shall not plug in,
regulate and clean the appliance or
perform user maintenance.
The appliance must be positioned so that
the plug is accessible.
Although this appliance complies with
safety standards, we do not recommend
its use on deep pile carpets or on long
hair type of rugs.
If the supply cord is damaged it must be
replaced by the manufacturer or service
agent or similarly qualified person in
order to avoid a hazard.
CAUTION: In order to avoid a hazard due
to inadvertent resetting of the thermal
cut-out, this appliance must not be
supplied through an external switching
device, such as a timer, or connected
to a circuit that is regularly switched on
and off by the utility.
CAUTION - Some parts of this product
can become very hot and cause burns.
Particular attention has to be given
where children and vulnerable people
are present.
Technical Information
Model No: DF2608-EUE, DF2608-INT, DF2608-AU, DF3020EUE, DF3020-INT
230V
Heat Output
240V
Nominal Heat Output
P Nom 1.9 - 2.0 kW
Minimum Heat Output
P min
0.9 - 1.0 kW
Maximum Continuous Heat Output P max,c 1.9 - 2.0 kW
Auxiliary Electricity Consumption
In Standby mode
el SB 0.41 - 0.42 W
with electronic room temperature control
General
Unpack the heater carefully and retain the packaging for
possible future use, in the event of moving or returning the
fire to your supplier.
The fire incorporates a flame effect, which can be used
with or without heating, so that the comforting effect may
be enjoyed at any time of the year. Using the flame effect
on its own only requires little electricity.
Before connecting the heater check that the supply
voltage is the same as that stated on the heater.
Please note: Used in an environment where background
noise is very low, it may be possible to hear a sound which
is related to the operation of the flame effect. This is normal
and should not be a cause for concern.
Electrical Connection
WARNING: THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the
voltage marked on the heater must correspond to the
supply voltage.
Before switching on, please read the safety warnings and
operating instructions.
Controls: See Fig. 3
Icon
Display
A
Function
Power /
Standby
-
Sleep
Timer
B
Flame Effect
C
f1
f2
fp
-
Press once to turn the product ‘ON’.
Press a second time to put the product into ‘STANDBY’
(When returning from ‘STANDBY’ mode the product will return to previous settings unless the product
has been plugged out, in which case it will reset to factory settings)
Press multiple times to change the ‘SLEEP TIMER’ in 0.5 hr increments from 0.5 hr to 8.0 hr before turning
off. The remaining time on the ‘SLEEP TIMER’ displays. (This icon is Green in Colour)
‘FLAME EFFECT’ button cycles the unit sequentially through the 4 setting, LOW FLAME, HIGH FLAME,
DEMO MODE and OFF.
Low
Flame
This setting will run the flame effect at a low brightness level. (The display will show F1)
High
Flame
This setting will run the flame effect at a high brightness level. (The display will show F2)
Demo
Mode
This setting will slowly pulse the flame effect between low and high brightness. (The display will show
FP)
Off
This will turn the flame effect off. If the heater is running, the display will activate and remain active to
read the set temperature and show if the product is on LOW HEAT/ HIGH HEAT/COOL BLOW.
Log Effect
D
Description
‘LOG EFFECT’ button cycles the unit sequentially through the 3 setting, ‘PULSING LOGS, STATIC LOGS
and OFF.
Lp
LS
Pulsing
Logs
This setting will make the logs pulse. (The display will show FP)
Static
Logs
This setting will make the logs stay lit. (The display will show FS)
-
Off
-
On / Off
E
This setting will turn the logs off.
This button cycles the top light ‘On’ and ‘Off’.
‘HEAT’ button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT, COOL BLOW
and OFF. The heat setting will be indicated by an icon in the floating display see Fig.1.
Heat
When the flame effect is ‘ON’ the floating display will turn off after 5 seconds, however if the heater is
being used independently of the flame effect. The low heat or high heat icon will appear continuously
in the floating display.
Low Heat
This setting will run the heater at ‘LOW HEAT’ this setting will be indicated by the ‘LOW HEAT’ icon
and the letters ‘LO’ appearing in the display.
(This icon is Orange in Colour)
High
Heat
This icon in the floating display indicates ‘HIGH HEAT’ this setting will be indicated by the ‘HIGH HEAT’
icon and the letters ‘HI’ appearing in the display.
(This icon is Red in Colour)
Cool
Blow
This icon in the floating display indicates ‘COOL BLOW’ this setting will be indicated by the ‘COOL
BLOW’ icon and the letters ‘CB’ appearing in the display.
(This icon is Blue in Colour)
F
Off
This switches the heater and blower ‘OFF’, no icon will be displayed in the floating display. Note the
blower will run for 10-20 seconds after being turned off this is to ensure the product cools down safely.
Temp
Down
Press multiple times to lower the heater temperature in 1°C increments. The lowest temperature that
can be set 5°C.
Note: Once you stop at your desired temperature this will flash 3 times, then the display will show the
room temperature as detected by the product. If the set temperature is lower than the detected
room temperature the heater will not activate.
Temp Up
Press multiple times to increase the heater temperature in 1°C increments. The highest temperature
that can be set 37°C.
Note: Once you stop at your desired temperature this will flash 3 times, then the display will show the
room temperature as detected by the product. If the set temperature is lower than the detected
room temperature the heater will not activate.
-
G
H
-
-
User Modes:
Mode Name /Description
Action (Actions cannot be input by remote control)
Change Celsius (° C) to Fahrenheit (° F)
Press both Temp+ (
) and Temp– (
) on the unit and hold until beep is heard and
display flashes. (To revert back to Celsius repeat this action)
Disable/Enable Heat Options
Hold both Heat (
) and Temp– ( ), on the unit, for 2 seconds, when the heater has
been disabled the display will read “--” and beep. To enable heat repeat this action.
Remote Control - See Fig. 3
The maximum range of use is ~ 5metres.
NOTE: It takes time for the receiver to respond to the
transmitter.
NOTE: The receiver for the remote control is located in
the display, aim the remote control in this direction when
inputting commands.
Do not press the buttons more than once within two
seconds for correct operation.
Battery Information - See Fig. 3
1. To activate the remote control remove the clear battery
isolation strip at the base of the remote control, which
is used to ensure your remote control reaches you fully
charged.
2. To replace the remote control battery, turn over the
remote control, and follow the diagram embossed on the
remote control
3. Only use CR2025 or CR2032 size of batteries.
Installing Front Glass- See Fig. 5, 6 & 7
NOTE: The outer glass is shipped separate to the firebox.
1. Remove the three screws holding the side trim as shown
in Fig. 5. and remove the metal trim.
2. Unpack the glass, ensure it is free from dust and finger
marks and slide in to position as shown in Fig. 6.
3. Position the metal trim removed in step 1, and secure
with the three screws as per Fig. 7
Fitting- See Fig. 4
IMPORTANT: If not using a Dimplex mantel, the fireplace
must be installed in an enclosure with the following
MINIMUM dimensions(Figure 4).
1. Select a suitable location that is not susceptible to
moisture and is at least 1 meter away from drapes,
furniture and high traffic.
2. Store the fireplace in a safe, dry and dust free location.
3. Clearance for air circulation beneath the fireplace
is provided by two spacers. DO NOT INSTALL FIREPLACE
DIRECTLY ON CARPET OR SIMILAR SURFACES WHICH MAY
RESTRICT AIR CIRCULATION. If installing the fireplace in
a carpeted area, place a one-piece, solid flat surface
under the fireplace. Ensure that all feet rest securely on
this surface!
4. In some jurisdictions this appliance is supplied without
a plug this is to comply with the local regulations. In such
instances this appliance must be installed by a suitably
qualified installer and the means for disconnection must
be incorporated in the fixed wiring in accordance with
the local wiring rules.
New Wall Construction
1. Select a suitable location that is not susceptible to
moisture and is away from drapes, furniture and high
traffic.
2. Place the fireplace in the desired location to see how
it will look in the room.
3. Mark the desired location on the floor.
4. Use studs to frame an opening of 680 mm wide X 585
mm high X 229 mm deep.(DF2608) Use studs to frame an
opening of 775 mm wide X 654mm high X 298 mm deep.
(DF3020)
Option #1
The power cord can be run from behind the trim and
along the wall to an outlet near the fireplace.
Option #2
A new outlet can be installed inside the framing
construction. Plug the fireplace into a 10-13Amp/230240 Volt outlet. If the cord does not reach you may use
a 3-core type extension cord rated for a minimum of
10 Amps.
Existing Fireplace
1. Seal all drafts and vents with a non-fibrous insulation
material to prevent any chimney debris from falling onto
the fireplace. Do not install into an existing fireplace that
is prone to dampness.
2. Cap the top of the chimney flue to prevent rain from
entering.
3. Plan your electric power supply.
4. The power cord can run along the front of the hearth
to an outlet near the fireplace.
Thermal Safety Cut-out
The built-in overheat cut-out, switches off the appliance
automatically in the event of a fault! Should this occur
switch off the appliance or disconnect the mains plug
from the socket.
Remove any obstructions which may have caused the
overheating. After a short cooling down phase, the
appliance is ready for use again! If the fault should occur
again, contact your local dealer!
WARNING: In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this appliance must not be
supplied through an external switching device, such as a
timer, or connected to a circuit that is regularly switched
on and off by the utility.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.
Light Emitting Diode
This fire is fitted with LED (Light Emitting Diode) lamps. These
LED lamps are maintenance-free and should not require
replacing during the life of the product.
Cleaning
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use
abrasive cleaners. The glass viewing screen should be
cleaned carefully with a soft cloth.
DO NOT use proprietary glass cleaners.
To remove any accumulation of dust or fluff the soft brush
attachment of a vacuum cleaner should occasionally be
used to clean the outlet grille of the fan heater.
WARNING: do not operate the product without the grille
and outer glass in position as this may effect the operation
of the heater.
Recycling
For electrical products sold within the European
Community. At the end of the electrical
products useful life it should not be disposed
of with household waste. Please recycle where
facilities exist. Check with your Local Authority
or retailer for recycling advice in your country.
After Sales Service
Should you require after sales service or should you need
to purchase any spares, please contact the retailer from
whom the appliance was purchased or contact the service
number relevant to your country on the warranty card.
Please do not return a faulty product to us in the first instance
as this may result in loss or damage and delay in providing
you with a satisfactory service. Please retain your receipt
as proof of purchase.