SP090 Installation Instructions

Spin Round Wall Spout - Installation Instructions
CONGRATULATIONS ON THE PURCHASE OF YOUR NEW CASA LUSSO TAPWARE,
WE HOPE YOU AND YOUR FAMILY ENJOY YOUR NEW PRODUCT AND CONSIDER US
FOR ANY FUTURE PROJECT. CASA LUSSO PRODUCTS HAVE BEEN MANUFACTURED
UNDER THE HIGHEST STANDARDS OF QUALITY AND WORKMANSHIP.
IMPOR TANT
IT IS IMPORTANT TO FLUSH OUT THE WATER
PIPES BEFORE INSTALLING THE MIXER.
TEFLON
TAPE
ELBOW
THREAD
BACK PLATE
Hot and cold water inlet pressures should be equal.
Inlet pressure range: 150 – 500 kPa
New Regulation:
500 kPa maximum operating pressure at any
outlet within a building. (Ref. AS/NZS 3500.1-2003, Clause 3.3.4)
Maximum hot water temperature: 80oC.
FEATUR ES
Premium Warranty:
7 Year replacement product : 1 year labour
Material: Chrome Plated Solid Brass Construction
WALL SPOUT
Includes: Bath Spout & Cover Plate
Made to Australian Standards code:
AS/NZS 3718:2005 Water supply - Tap ware LN23083
Apply teflon tape to elbow thread.
Screw Wall Spout onto elbow thread by hand and tighten firmly.
Test & check for leaks
Slide Back Plate to Wall to cover wall penetration.
G E N E R A L I N F ORMA T IO N
• When installing this product, the pipes must be flushed clean where
the product is being installed.
o
• If the water temperature exceeds 80 C an approved water
tempering valve must be fitted.
• For domestic use only, not suitable for commercial applications.
MAINTENANCE
• Clean regularly using mild soap and dry with a soft cloth.
• Do Not use abrasive cleaners or harsh detergents.
The warranty will not apply if:
• The product has been damaged by improper use;
• The product has not been used in accordance with any
applicable instruction guide;
• The purchaser has attempted to modify or repair the product;
• The product is not installed by a licenced Plumber.
FAILURE TO COMPLY WITH ANY OF THE ABOVE INSTRUCTIONS WILL VOID ALL WARRANTIES
www.casalusso.com.au
Spin Wall Top Assemblies - Installation Instructions
CONGRATULATIONS ON THE PURCHASE OF YOUR NEW CASA LUSSO TAPWARE,
WE HOPE YOU AND YOUR FAMILY ENJOY YOUR NEW PRODUCT AND CONSIDER US
FOR ANY FUTURE PROJECT. CASA LUSSO PRODUCTS HAVE BEEN MANUFACTURED
UNDER THE HIGHEST STANDARDS OF QUALITY AND WORKMANSHIP.
IMPOR TANT
IT IS IMPORTANT TO FLUSH OUT THE WATER
PIPES BEFORE INSTALLING THE MIXER.
Hot and cold water inlet pressures should be equal.
Inlet pressure range: 150 – 500 kPa
New Regulation:
500 kPa maximum operating pressure at any
outlet within a building. (Ref. AS/NZS 3500.1-2003, Clause 3.3.4)
Maximum hot water temperature: 80oC.
G EN E R A L I N FO RMA T ION
• When installing this product, the pipes must be flushed clean where
the product is being installed.
o
• If the water temperature exceeds 80 C an approved water
tempering valve must be fitted.
• For domestic use only, not suitable for commercial applications.
MAINTENANCE
• Clean regularly using mild soap and dry with a soft cloth.
• Do Not use abrasive cleaners or harsh detergents.
FEATUR ES
Premium Warranty:
7 Year replacement product : 1 year labour
Material: Chrome Plated Solid Brass Construction
Includes: Wall Top Assemblies ( Hot & Cold )
Made to Australian Standards code:
AS/NZS 3718:2005 Water supply - Tap ware LN23083
The warranty will not apply if:
• The product has been damaged by improper use;
• The product has not been used in accordance with any
applicable instruction guide;
• The purchaser has attempted to modify or repair the product;
• The product is not installed by a licenced Plumber.
C O N TE N TS








50
60


Handle


 Set Screw

 Adapter Screw 
Spindle Handle Adapter
Spindle Lock Flange

75
50


Fibre Washer
Spindle
Locknut
NOT INCLUDED



Standard Tap Seat Body
Wall stud
Nogging
FAILURE TO COMPLY WITH ANY OF THE ABOVE INSTRUCTIONS WILL VOID ALL WARRANTIES
www.casalusso.com.au
Spin Wall Top Assemblies - Installation Instructions
B EFO R E S TA RT IN G
• Install the Spindles hand-tight until the seal of the Spindle firmly makes contact with the seat.
• Using a n a p p r o pri at e spanner tighten the Spindle another 1/8th of a turn. Do not over-tighten.
• Over-tightening the Spindles could damage the ceramic discs and in turn, void the manufacturer's warranty.
• Place the Fibre washer over the seated Spindle and fit the Spindle Locknut.
1
2
Finished Wall Surface
Wall Stud
Spindle Lock
Flange
Locknut
Maximum
40mm round
10-20mm
Spindle
Nogging
Seal wall opening before final fit off.
4
3
Cut-off gauge
Cut-off remaining thread against the gauge, after
cutting use a file to ensure the spindle is flat & square.
Cut-off gauge must be tightened to Spindle Lock Flange.
Spindle Lock Flange must be tightened to finished wall surface.
5
6
Spindle handle
adapter
Remove cut-off gauge and deburr inside of locknut after cutting.
7
Set screw engagement slot to be positioned on underside.
8
Handle
2-3mm
Adapter
screw
Screw the adapter screw into the Spindle handle
adapter, than place the handle on top.
Position handle 2-3mm from finished wall and screw
set screw into slot of Spindle handle adapter.
www.casalusso.com.au
Download PDF

advertising