PARTY POP™ & TEKNO™ SCOOTERS
OWNER’S MANUAL
Read and understand this entire manual before allowing
child to use this product! For assistance contact Razor.
DO NOT RETURN TO STORE.
NOTE: Manual illustrations are for demonstration purposes only.
Illustrations may not reflect exact appearance of actual product.
Specifications subject to change without notice.
Please have your product along with the 22 character product I.D. code with you
before contacting Razor for warranty assistance and/or replacement parts.
Product I.D. Code: _____________ - ____________ - ____________
CONTENTS
Safety Warnings............................................................................................... 1
Before You Begin.............................................................................................. 2
Assembly and Set-Up....................................................................................... 3
Pre-Ride Checklist............................................................................................. 4
Usage................................................................................................................ 4
Repair and Maintenance.................................................................................. 5
Product Parts..................................................................................................... 6
Warranty and Contact Information................................................................... 7
SAFETY WARNINGS
ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Direct parental supervision is required. Scooters are meant to be used only
in controlled environments free of potential traffic hazards and not on public
streets. Do not allow your child to ride a scooter in any areas where vehicle
traffic is present. Child must maintain a hold on the handlebars at all times.
Never allow more than one child at a time to ride a scooter. Never use near
steps, sloped driveways, hills, roadways, alleys or swimming pool areas.
AN IMPORTANT MESSAGE TO PARENTS: This manual
contains important information. For your child’s safety, initial setup and
steering tube installation require adult assistance for young riders. It is
your responsibility to review this information with your child and make sure
that your child understands all warnings, cautions, instructions and safety
topics. Razor USA recommends that you periodically review and reinforce
the information in this manual with younger riders, and that you inspect and
maintain your child’s scooter to ensure their safety.
Do not ride a scooter in wet weather. Scooters are intended for use on solid,
flat, clean and dry surfaces, such as pavement or level ground, without loose
debris, such as rocks or gravel. Wet, slick or uneven and rough surfaces may
impair traction and contribute to possible accidents. Do not ride a scooter in
mud, ice, puddles or water. Avoid excessive speeds that can be associated
with downhill rides. Never risk damaging surfaces, such as carpet or flooring,
by use of a scooter indoors. Do not ride at night or when visibility is impaired.
GENERAL WARNING: Scooter riding can be a hazardous activity.
Scooters can and are intended to move, and it is therefore possible to get into
dangerous situations and/or lose control and/or fall. If such things occur you
can be seriously injured or die. LIKE ANY OTHER MOVING PRODUCT, USING
A SCOOTER CAN BE A DANGEROUS ACTIVITY AND MAY RESULT IN INJURY
OR DEATH EVEN WHEN USED WITH PROPER SAFETY PRECAUTIONS. USE AT
YOUR OWN RISK AND USE COMMON SENSE.
PROPER RIDING ATTIRE
Always ensure child is wearing proper protective equipment, such as an
approved safety helmet. A helmet may be legally required by local law or
regulation in your area. A child should always wear shoes and keep shoelaces
tied and out of the way of the wheels. Never ride barefooted or in sandals.
Knee pads and elbow pads are recommended.
• Always wear safety equipment, such as helmet, knee pads and elbow pads.
Always wear a helmet when riding your scooter and keep the chinstrap
securely buckled.
• Always wear closed toe shoes.
• Ride on smooth, paved surfaces away from motor vehicles.
• Avoid sharp bumps, drainage grates, and sudden surface changes. Scooter
may suddenly stop.
• Avoid streets and surfaces with water, sand, gravel, dirt, leaves, and other
debris. Wet weather impairs traction, braking, and visibility.
• Do not ride at night.
• Brake will get hot from continuous use. Do not touch after braking.
• Avoid excessive speed associated with downhill rides.
• Obey all local traffic and scootering laws and regulations.
• Watch out for pedestrians.
• Do not exceed 143 lb (65 kg) total weight on the scooter.
• Do not allow children under age six (6) to use the scooter. These scooters
are for children ages six (6) and above. Children under age eight (8) should
ride with adult supervision at all times. All children and preteens should
ride with adult guidance at all times.
• Rider weight does not necessarily mean a child’s size is appropriate to fit or
maintain control of the scooter.
• A parent’s decision to allow his or her child to ride this product should be
based on the child’s maturity, skill and ability to follow rules.
WARNING: ALWAYS INSPECT SCOOTER PRIOR TO RIDING. Properly
inspecting and maintaining your scooter can reduce the risk of injury. Always
inspect your scooter before riding and regularly maintain it.
WARNING: CHECK LOCAL LAWS REGARDING SCOOTER USE. Check
local laws and regulations to see where and how you may use your Razor
scooter legally. In many states and local areas scooter riders are required
BY LAW to wear a helmet. Check local laws and regulations regarding laws
governing helmet use and scooter operation in your area.
WARNING: BUTTON/COIN CELL BATTERY
• This product contains a Button or Coin Cell Battery. A swallowed Button or
Coin Cell Battery can cause internal chemical burns leading to death in as
little as two hours. Dispose of used batteries immediately. Keep new and
used batteries away from children. If you think batteries might have been
swallowed or placed inside any part of the body, seek immediate medical
attention.
• Batteries included for lights - adult attention for changing and disposal.
• Battery should only be replaced by an adult.
• Loose battery could present a choking hazard and should be kept away from
small children.
• Dispose of batteries properly.
FAILURE TO USE COMMON SENSE AND HEED THE ABOVE
WARNINGS FURTHER INCREASES RISK OF SERIOUS INJURY. USE
AT YOUR OWN RISK AND WITH APPROPRIATE AND SERIOUS
ATTENTION TO SAFE OPERATION. USE CAUTION.
1
BEFORE YOU BEGIN
Remove contents from box. Inspect the contents of the box for scratches in the paint and/or dents that may have
occurred during shipping. Because your scooter was partially assembled and packed at the factory, there should not be
any problems, even if the box has a few scars or dents.
Grips
WARNING: DO NOT USE
NON-RAZOR PRODUCTS WITH
YOUR SCOOTER. Razor scooters
have been built to certain Razor
design specifications. The
original equipment supplied at
the time of sale was selected
on the basis of its compatibility
with the frame, fork and all
other parts. Certain aftermarket
products may not be compatible
and will void the warranty.
T-bar
Collar Clamp
Product ID Locations:
See locations to the left
LED Light Button
Battery Compartment
1. Deck (Underneath Unit)
2. Box - Side of UPC (Not Shown)
1
Required Tools
Box Contents:
• Scooter
• Allen Wrench
• Owner’s Manual
5 mm
Allen wrench
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
2
ASSEMBLY AND SET-UP
Assembling the Handlebars
WARNING: Failure to
properly engage the spring-loaded
buttons may cause the handlebars
to dislodge while riding and may
cause rider to lose control and
fall. When correctly engaged, the
handlebars will not rotate nor move
sideways, and the spring-loaded
buttons will be clearly visible in the
holes on the T-bar.
WARNING: Check hand
grips regularly for wear or damage,
as grips are designed to aid in
gripping handlebars and to provide
some protection against possible
impact. Replace immediately if
worn, torn, damaged or missing.
Assembling the T-bar
WARNING: Failure to
properly install and tighten the
pivoting mechanism and the
plastic cover may cause the rider
to lose control and fall. If you do
not understand these instructions,
contact Razor customer care for
assistance.
Tool required: 5 mm Allen wrench
WARNING: Do not
attempt to thread the handle bar
into the front fork thread. Tighten
clamp securely.
1 Loosen the collar clamp and slide
it upward. Insert T-bar into the fork
until it bottoms out on the headset
locknut.
Note: If necessary, carefully twist
the T-bar side to side while pushing
downward until T-bar bottoms out
on the headset locknut.
2 With the front wheel pointed
straight ahead, the handlebars
square to the front wheel and
the Razor logo facing the front,
tighten the clamp as shown.
Tighten securely.
Activating the Batteries
1 To activate the batteries, locate
the battery compartment on the top
of the deck and remove the plastic
tab from under the battery cover.
3
PRE-RIDE CHECKLIST
Safety Gear
Deck and Handlebars
Always wear proper protective gear, such as an approved safety
helmet. Elbow pads and kneepads are recommended. Always wear
closed toe shoes (lace-up with rubber soles) and keep shoelaces
tied and out of the way of the wheels. NEVER RIDE BAREFOOTED
OR IN SANDALS.
Check for cracks or broken connections. Although broken decks
are rare, it is possible for an aggressive rider to run into a curb
or object and wreck and bend or break the deck. Get in the habit
of inspecting your scooter on a regular basis.
Hardware/Loose Parts
Laws and Regulations
Check and secure all fasteners before every ride. Make sure the
collar clamp is locked properly into place before riding.
There should not be any unusual rattles or sounds from loose
parts or broken components. If the unit is damaged, do not ride.
Reference “Safety Warnings” on page 1 of this manual.
Always check and obey any local laws or regulations.
Be Careful!
This product is not for aggressive or trick riding. Avoid steep
inclines and don’t ride too fast — you can lose control and fall.
Skateboard parks are not designed for young riders. Never ride in
traffic or on the street and watch your surroundings for pedestrians,
bikers, boarders and skaters.
Maintain a hold on the handlebars at all times.
USAGE
How to Ride
Place one foot on the baseboard and push forward with the other foot. Steer with both hands on the handlebars. For
enhanced cornering, lean slightly into the direction of the turn.
Gently step on the LED light button to activate the LED lights. Lights will remain on for approximately 20 seconds after
button has been released. Gently step on the LED light button again to re-activate the lights.
How to Stop
For controlled stops, apply the brake by stepping on the brake. Razor recommends that you practice applying the brake
at various speeds and in an open area free from obstructions before riding your Razor scooter around others.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
4
REPAIR AND MAINTENANCE
Cleaning
Wipe with a damp cloth to remove dirt and dust. Do not use industrial cleaners or solvents, as they may damage the
surfaces. Do not use alcohol, alcohol-based or ammonia-based cleaners, as they may damage or dissolve the plastic
components or soften the decals or decal adhesive.
Collar Clamp
Tool required: 5 mm Allen wrench
1 Using a 5 mm Allen wrench,
check that the collar clamp bolt
is tightened securely. Make sure
the front wheel is pointed straight
ahead and the handlebars is
squared to the front wheel.
Replacing the Batteries
1 Using a coin, loosen the battery
cover by turning clockwise then
remove cover.
WARNING:
• Lithium batteries included
for lights - adult attention for
changing and disposal.
• Battery should only be replaced
by an adult.
• Loose batteries could present
a choking hazard and should be
kept away from small children.
• Dispose of batteries properly.
2 Discard both old batteries and
3 Replace cover and secure
replace with two (2) CR2032L 3V
Lithium batteries. Note: Make
sure to install BOTH batteries
positive (+) side up.
with a coin by turning
counterclockwise.
Wheels and Bearings
Under normal circumstances and conditions, Razor wheels and wheel bearings are maintenance free. Nonetheless,
it is the responsibility of the owner or guardian to periodically inspect the wheels for wear and tear, the axle for
proper tightness, bearings for side-to-side play, and for loose parts. When a wheel develops play, this is an indication
of excess wear and replacement is necessary. Replace immediately with only genuine Razor wheels. Worn wheels/
bearings are considered normal wear-and-tear and are not covered by the Razor Warranty. Wheels other than
genuine Razor wheels may not be compatible with your Razor scooter. The use of anything other than genuine Razor
replacement parts may affect your safety and will void your warranty.
Replacement Parts
The most frequently requested replacement parts are available for purchase at some Razor retail partners.
For the complete selection of replacement parts visit shop.razor.com.
Repair Centers
For a list of authorized Razor repair centers:
• Check online at www.razor.com.
• Additional Customer Service contact information is listed at the back of this manual.
5
Note: Batteries are not covered
under the limited warranty.
WARNING: Wheelies and
other stunt-type riding reduces your
ability to maneuver and control
your scooter. Take the necessary
precautions, such as wearing
appropriate protective gear, and
practice in an area safe for stunt
riding and free from obstructions.
PRODUCT PARTS
Keep your scooter running for years with genuine Razor parts. Visit our web site for more information on spare part availability. (Illustrations may not reflect exact
appearance of actual product. Specifications subject to change without notice.)
1.
2.
3.
4.
5.
6.
7.
Handlebars
Handlebar Grips
T-Bar
Collar Clamp
Headset
Front Fork
Wheels (Front/Rear)
7-1. Axle Bolts (Front/Rear)
8. Brake
9. Battery Cover
10. Batteries CR2032L 3V (x2)
11. Deck Plate w/ LED Lights
11-1. LED Light Button
1
2
2
3
4
8
7
7-1
7-1
5
9
10
11
11-1
6
7-1
7
7-1
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
6
WARRANTY
Razor Limited Warranty
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
The manufacturer warranties this product to be free of manufacturing defects
for a period of 6 months from date of purchase. This Limited Warranty does not
cover normal wear and tear, or any damage, failure or loss caused by improper
assembly, maintenance, or storage.
Razor does not offer an extended warranty. If you have purchased an extended
warranty, it must be honored by the store at which it was purchased.
For your records, save your original sales receipt with this manual and write
the serial number below.
This Limited Warranty will be void if the product is ever:
• used in a manner other than for recreation or transportation;
• modified in any way;
• rented.
__________________________________________
CUSTOMER SERVICE CONTACT INFORMATION
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed below:
AMERICAS
EUROPE
ASIA
Razor USA LLC
P.O. Box 3610
Cerritos, CA 90703
USA
Razor USA LLC (Europe)
Handelsweg 2
2742 RD Waddinxveen
Netherlands
Razor USA LLC (Asia)
P.O. Box 3610
Cerritos, CA 90703
USA
+1 866 467 2967
Monday - Friday
8:00 AM - 5:00 PM Pacific Time
customersupport@razorusa.com
+44 (0) 120 267 2702
info@razoreu.com
+81 50 7579 6622
info@razor-asia.com
DISTRIBUTED IN THE UK BY:
DISTRIBUTED IN AUSTRALIA BY:
Re:creation Limited
2 Meadows Business Park
Station Approach, Blackwater
Camberley, Surrey GU17 9AB
United Kingdom
Funtastic Limited
Level 2, Tower 2, Chadstone Place
1341 Dandenong Road
Chadstone VIC 3148
Australia
+44 (0) 118 973 6222 Tel
+44 (0) 118 973 6220 Fax
sales@recreationltd.co.uk
+1 800 244 543
info@funtastic.com.au
Printed in China for Razor USA LLC.
Copyright © 2003-2017 Razor USA LLC. All rights reserved. Razor® and the Razor logo design
are among the registered trademarks of Razor USA LLC and/or its affiliated companies in the
United States and/or select foreign countries. PartyPop™ and Tekno™ are trademarks of Razor
USA LLC and/or its affiliated companies in the United States and/or selected foreign countries.
7
US_170306