BUNN
®
VPR
VPS
OPERATING & SERVICE MANUAL
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
10053.0000L
01/05 ©1996 Bunn-O-Matic Corporation
www.bunnomatic.com
INTRODUCTION
This equipment will brew a half-gallon batch of coffee into an awaiting dispenser. It is only for indoor use on
a sturdy counter or shelf.
WARRANTY
Bunn-O-Matic Corp. (“Bunn”) warrants the equipment manufactured by it to be commercially free from defects
in material and workmanship existing at the time of manufacture and appearing within one year from the date of
installation. In addition:
1.) Bunn warrants electronic circuit and/or control boards to be commercially free from defects in material and
workmanship for three years from the date of installation.
2.) Bunn warrants the compressor on refrigeration equipment to be commercially free from defects in material
and workmanship for two years from the date of installation.
3.) Bunn warrants that the grinding burrs on coffee grinding equipment will grind coffee to meet original factory
screen sieve analysis for three years from date of installation or for 30,000 pounds of coffee, whichever comes first.
This warranty does not apply to any equipment, component or part that was not manufactured by Bunn or that,
in Bunn’s judgement, has been affected by misuse, neglect, alteration, improper installation or operation, improper
maintenance or repair, damage or casualty.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR
ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of Bunn are
not authorized to make modifications to this warranty or to make additional warranties that are binding on Bunn.
Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and should not
be relied upon.
The Buyer shall give Bunn prompt notice of any claim to be made under this warranty by telephone at (217)
529-6601 or by writing to Post Office Box 3227, Springfield, Illinois, 62708-3227. If requested by Bunn, the Buyer
shall ship the defective equipment prepaid to an authorized Bunn service location. If Bunn determines, in its sole
discretion, that the equipment does not conform to the warranty, Bunn shall repair the equipment with no charge
for parts during the warranty period and no charge for labor by a Bunn Authorized Service Representative during
the warranty period. If Bunn determines that repair is not feasible, Bunn shall, at its sole option, replace the
equipment or refund the purchase price for the equipment.
THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE
OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AS
SPECIFIED HEREIN, TO REPAIR OR, AT BUNN’S SOLE OPTION, REPLACEMENT OR REFUND.
In no event shall Bunn be liable for any other damage or loss, including, but not limited to, lost profits, lost sales,
loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute
equipment, facilities or services, or any other special, incidental or consequential damages.
Page 2
10053 073001
USER NOTICES
Carefully read and follow all notices in this manual and on the equipment. All labels on the equipment should
be kept in good condition. Replace any unreadable or damaged labels.
#00658.0000
#00831.0000
POUR IN WATER ONLY
To reduce the risk of electric shock,
do not remove or open cover.
No user-serviceable parts inside.
Authorized service personnel only.
Disconnect power before servicing.
#00833.0000
#37881.0000
#12364.0000
Page 3
10053 011405
ELECTRICAL REQUIREMENTS
CAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up.
The brewer has an attached cordset and requires 2-wire grounded service rated 120 volts ac, 15 amp, single
phase, 60 Hz.
“A" models require 2-wire, grounded service rated 220 - 240 volts ac, 20 amp, single phase, 50 Hz. Proceed
as follows:
Electrical Hook-Up (Model "A" Only)
CAUTION – Improper electrical installation will damage electronic components.
1. An electrician must provide electrical service as specified.
2. Using a voltmeter, check the voltage and color coding of each conductor at the electrical source.
3. Plug the power cord into the power connector located in the base on the rear of the brewer.
INITIAL SET-UP
CAUTION - The brewer must be disconnected from the power source throughout the initial set-up, except
when specified in the instructions.
1.
2.
3.
Insert an empty funnel into the funnel rails.
Place an empty dispenser under the funnel.
Pour three pitchers of tap water into the screened area on top of the brewer. Allow approximately two minutes
between pitchers for water to flow into the tank. While the third pitcher of water is entering the tank, the tank
will fill to capacity and the excess will flow from the sprayhead, out of the funnel, and into the dispenser.
4. When the flow of water from the funnel stops, connect the brewer to the power source and wait approximately
twenty minutes for the water in the tank to heat to the proper temperature. Some water will drip from the funnel
during this time; this is due to expansion and should not occur thereafter.
5. Empty the dispenser and replace it under the funnel.
6. Pour one pitcher of tap water into the screened area on top of the brewer.
7. When water has stopped flowing from the funnel let the water in the tank reheat to the proper temperature.
8. Empty the dispenser. The brewer is now ready for use in accordance with the coffee brewing instructions
below.
NOTE: The control thermostat will need to be adjusted downward to compensate for high altitudes. Refer to
Steaming and spitting around the funnel on page 5 for instructions.
COFFEE BREWING
1.
2.
3.
4.
5.
6.
Insert a BUNN® filter into the funnel.
Pour the fresh coffee into the filter and level the bed of grounds by gently shaking.
Slide the funnel into the funnel rails.
Place an empty dispenser beneath the funnel.
Pour one pitcher of tap water into the screened area on top of the brewer.
When brewing is completed, simply discard the grounds and filter.
CLEANING
1.
The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all
surfaces on Bunn-O-Matic equipment.
2. Check and clean the sprayhead. The sprayhead holes must always remain open.
3. With the sprayhead removed, insert the deliming spring (provided) all the way into the sprayhead tube. When
inserted properly, no more than two inches of spring should be visible. Saw back and forth five or six times.
NOTE – In hard water areas, this may need to be done daily. It will help prevent liming problems in the brewer
and takes less than a minute.
10053 111104
Page 4
TROUBLESHOOTING
A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems
encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic
Technical Service Department.
•
•
Inspection, testing, and repair of electrical equipment should be performed only by qualified service personnel.
This brewer is heated at all times. Keep away from combustibles.
WARNING – •
•
•
•
Exercise extreme caution when servicing electrical equipment.
Unplug the brewer when servicing, except when electrical tests are specified.
Follow recommended service procedures
Replace all protective shields or safety notices
PROBLEM
PROBABLE CAUSE
REMEDY
Water is not hot
1. Limit Thermostat or Thermal
Cut-Off
CAUTION - Do not eliminate or
bypass limit thermostat/thermal
cut-off. Use only BOM replacement part.
Limit Thermostat - #29329.0001
Thermal Cut-off - #04776.0000
Refer to Service - Limit Thermostat or Thermal Cut-Off for
testing procedures. See page 10
or 13
2. Control Thermostat
Refer to Service - Control Thermostat for testing procedures.
See page 9
3. Tank Heater
Refer to Service - Tank Heater
for testing procedures. See page
12
1. Lime Build-up
CAUTION - Tank and tank
components should be delimed
regularly depending on local
water conditions. Excessive
mineral build-up on stainless
steel surfaces can initiate corrosive reactions resulting in
serious leaks.
Inspect the tank assembly for
excessive lime deposits. Delime
as required.
2. Control Thermostat
Refer to Service - Control Thermostat for testing procedures.
See page 9
Spitting or excessive steaming
Page 5
10053 011405
TROUBLESHOOTING (cont.)
PROBLEM
Dripping from sprayhead
PROBABLE CAUSE
1. Lime Build-up
CAUTION - Tank and tank
components should be delimed
regularly depending on local
water conditions. Excessive
mineral build-up on stainless
steel surfaces can initiate corrosive reactions resulting in
serious leaks.
REMEDY
Inspect the tank assembly for
excessive lime deposits. Delime
as required.
1. Dispenser
Beverage overflows dispenser
The dispenser must be completely empty before starting a
brew cycle.
1. Filter Type
Weak beverage
BUNN® paper filters must be used
for proper extraction.
2. Coffee Grind
A fine or drip grind must be used
for proper extraction.
3. Sprayhead
A six-hole stainless steel sprayhead must be used for proper
extraction.
4. Funnel Loading
The BUNN® paper filter must be
centered in the funnel and the bed
of grounds leveled by gentle shaking.
5. Water Temperature
Place an empty funnel on an empty
dispenser beneath the sprayhead.
Pour-in a pitcher of tap water and
check the water temperature immediately below the sprayhead
with a thermometer. The reading
should not be less than 195°F.
Adjust the control thermostat to
increase the water temperature.
Replace if necessary.
Page 6
10053 011597
TROUBLESHOOTING (cont.)
PROBLEM
PROBABLE CAUSE
REMEDY
Dry coffee grounds remain in
the funnel
1. Funnel Loading
The BUNN® paper filter must be
centered in the funnel and the bed
of grounds leveled by gently shaking.
Brewer is making unusal noises
1. Tank Heater
Remove and clean lime off the
tank heater. See page 12
Cool beverage serving temperature
1. ON/OFF Warmer Switch
Refer to Service - ON/OFF
Warmer Switch for testing
procedures. See page 11
2. Warmer Element(s)
Refer to Service - Warmer
Element(s) for testing procedures. See page 14
Page 7
10053 011597
Page 8
SERVICE (cont.)
"ON" (fully counterclockwise for thermostat with
tee handle control or fully clockwise for thermostats with control knob). Plug-in the brewer to
the power source. The indication must be:
a) 120 volts ac for two wire 120 volt models.
b) 220 volts ac for two wire 220 volt models.
Voltage must not be present across these terminals
when the thermostat is turned "OFF" (fully counterclockwise).
8. Disconnect the brewer from the power source.
CONTROL THERMOSTAT
If voltage is present as described, reinstall the capillary
tube into the tank to the line 4.5" above the bulb, the
control thermostat is operating properly.
If voltage is not present as described, replace the
thermostat.
Removal and Replacement:
1. Remove wires from control thermostat leads or
terminals.
P2414
FIG. 3 CONTROL THERMOSTAT
Location:
The control thermostat is located inside the hood
on the left end of the mounting bracket.
Test Procedures:
1. Disconnect the brewer from the power source.
2. Locate the black wire on the control thermostat.
3. Check the voltage across the black wire on the
control thermostat and the white wire on the tank
heater or the red wire on the tank heater with a
voltmeter. Plug-in the brewer to the power source.
The indication must be:
a) 120 volts ac for two wire 120 volt models.
b) 220 volts ac for two wire 220 volt models.
4. Disconnect the brewer from the power source.
If voltage is present as described, proceed to #5.
If voltage is not present as described, refer to the
wiring diagrams and check the brewer wiring harness.
5.
6.
7.
Locate the blue/black wire on the control thermostat.
Gently remove the capillary bulb and grommet
from the tank.
Check the voltage across the blue/black wire of
the control thermostat and the white wire on the
tank heater or red wire on the tank heater with a
voltmeter when the control thermostat is turned
Page 9
BLU to BLU/BLK Lead
from Limit Thermostat
BLK to BLK Lead from
Terminal Block
EARLY MODELS
BLK to Terminal Block
BLU/BLK to
Limit Thermostat
or Thermal Cut-Off
P1252
FIG.4 CONTROL THERMOSTAT TERMINALS
10053 073001
SERVICE (cont.)
CONTROL THERMOSTAT (cont.)
2.
3.
4.
5.
6.
Remove the thermostat capillary bulb by firmly
pulling-up on the capillary at the tank lid. This will
disengage the grommet from the tank lid.
Remove the two #8-32 screws securing the control thermostat to the mounting bracket inside
the hood.
Slide the grommet to the line 4.5" above the bulb
on the new capillary tube.
Insert the capillary bulb through the hole in the
tank lid and press the grommet firmly and evenly
so that the groove in the grommet fits into the
tank lid.
Carefully bend the capillary tube so that the tube
and bulb inside the tank are in the vertical position.
NOTE - The capillary tube must be clear of any electrical termination and not kinked.
7.
8.
9.
Test Procedures:
1. Disconnect the brewer from the power source.
2. Disconnect the blue/black and black wires from
the limit thermostat.
3. Check for continuity across the limit thermostat
terminals with an ohmmeter.
If continuity is present as described, the limit thermostat is operating properly.
If continuity is not present as described, replace the
limit thermostat.
Removal and Replacement:
1. Remove all wires from limit thermostat terminals.
2. Carefully slide the limit thermostat out from
under the retaining clip and remove limit thermostat.
3. Carefully slide the new limit thermostat into the
retaining clip.
4. Refer to Fig. 6 when reconnecting the wires.
Using two #8-32 screws secure the control thermostat to the mounting bracket inside the hood.
Refer to Fig. 4 when reconnecting the wires.
Adjust the control thermostat as required
BLK to Tank
Heater
BLU/BLK to Control
Thermostat
LIMIT THERMOSTAT - VPR, VPS
P1800
FIG. 6 LIMIT THERMOSTAT TERMINALS
P2414
FIG. 5 LIMIT THERMOSTAT
Location:
The limit thermostat is located inside the hood on
the right side of the tank lid.
Page 10
10053 073001
SERVICE (cont.)
4.
ON/OFF WARMER SWITCH
b) 220 volts ac for two wire 220 volt models.
Disconnect the brewer from the power source.
If voltage is present as described, proceed to #5.
If voltage is not present as described, refer to the
Wiring Diagrams and check the brewer wiring harness.
LY
ON
ER LY
WAT ON
INATER
UR W
PO IN
UR
To
d re
o
N n d
u
A o u ot ce
D uth se re th
is o r- m e
co ri s o ri
n ze erv ve sk
n d ic o
ec s
r o
t erv ea op f e
b
p
o ic le en lec
w e p
er p a co tric
b ers rts ve s
efo
o in r. ho
ck
re nn sid
,
se el e
rv on .
ic ly
in .
g
.
PO
5.
Remove both wires from the switch and check for
continuity across the terminals with the switch in
the "ON" position. Continuity must not be present
when the switch is in the "OFF" position.
If continuity is present as described, reconnect the
wires to the terminals.
If continuity is not present as described, replace the
switch.
VPS
P3447
Removal and Replacement:
1. Remove the wires from the switch terminals.
2. Compress the clips inside the hood and gently
push the switch through the opening.
3. Push the new switch into the opening and spread
the clips to hold switch in the hood.
4. Refer to Fig. 8 when reconnecting the wires
WHI/RED to Brew Station Warmer
VIO to Upper Warmer
BRN/BLK to Lower Right Warmer
BLK to Cordset
#1
#2
#3
WHI to Cordset
P1131
VPR
P2412
VPS Models & VPR Models with Lighted switches
FIG. 7 ON/OFF WARMER SWITCHES
Location:
The ON/OFF warmer switches are located on the
front of the hood.
BLK to Cordset
WHI/RED to Brew Station Warmer & Lamp
VIO to Upper Warmer & Lamp
BRN/BLK to Lower Right Warmer & Lamp
Test Procedure:
VPS Models & VPR Models without Lighted switches
1. Disconnect the brewer from the power source.
2. Viewing the switch from the back locate the black
BLK to Cordset
wire from the switch terminal.
WHI/RED to Brew Station Warmer & Lamp
3. With the switch in the "ON" position check the
VIO to Upper Warmer & Lamp
voltage across the black wire of the switch and
BRN/BLK to Lower Right Warmer & Lamp
the white wire on the lamp or red wire on the lamp
VPRA & VPSA Models
P1253
with a voltmeter. Plug-in the brewer to the power
source. The indication must be:
FIG. 8 ON/OFF WARMER SWITCH TERMINALS
a) 120 volts ac for two wire 120 volt models.
10053 011405
Page 11
SERVICE (cont.)
If continuity is present as described, reconnect the
wires, the tank heater is operating properly.
If continuity is not present as described, replace the
tank heater.
TANK HEATER
NOTE- If the tank heater remains unable to heat,
remove and inspect heater for cracks in the sheath.
P2414
FIG. 9 TANK HEATER
Location:
The tank heater is located inside the tank
and secured to the tank lid.
Test Procedures:
1. Disconnect the brewer from the power supply.
2. Check the voltage across the black and white
wires on 120 volt models or the black and red
wires for 220 volt models with a voltmeter. Plugin the brewer to the power source. The indication
must be:
a) 120 volts ac for two wire 120 volt models.
b) 220 volts ac for two wire 220 volt models.
3. Disconnect the brewer from the power source.
If voltage is present as described, proceed to #4
If voltage is not present as described, refer to the
Wiring Diagrams and check wiring harness.
4.
5.
Disconnect the black wire and the white wire or
red wire from the tank heater terminals.
Check for continuity across the tank heater terminals.
Removal and Replacement:
1. Remove the tank inlet fitting securing the fill
basin to the tank lid, remove fill basin and tank
inlet gasket. Set all three parts aside for reassembly.
2. Disconnect the black wire on the terminal block
from the tank heater and disconnect the blue/
black wire from the limit thermostat or thermal
cut-off to the control thermostat.
3. Disconnect the black wire and the white or red
wire from the tank heater terminals.
4. Remove sprayhead and the hex nut securing the
sprayhead tube to the hood. Set aside for reassembly.
5. Remove the eight #8-32 nuts securing the tank
lid to the tank.
6. Remove the tank lid with limit thermostat or
thermal cut-off, sprayhead tube and tank heater.
7
Remove the two hex nuts securing the tank
heater to the tank lid. Remove tank heater with
gaskets and discard.
8. Install new tank heater with gaskets on the tank
lid and secure with two hex nuts.
9. Install tank lid with limit thermostat or thermal
cut-off, sprayhead tube and tank heater using
eight #8-32 hex nuts.
10. Secure sprayhead tube to hood using a hex nut.
11. Install sprayhead.
12. Reconnect the wires to the limit thermostat or
thermal cut-off, tank heater and control thermostat. See limit thermostat, thermal cut-off and
control thermostat sections in this manual when
reconnecting wires.
13. Install fill basin, secure with tank inlet fitting and
gasket.
14. Refer to Fig. 10 when reconnecting the tank
heater wires.
Page 12
10053 073001
SERVICE (cont.)
TANK HEATER (Cont.)
Location:
The thermal cut-outs are located inside the hood
connected to the tank heater terminals.
BLK to Limit Thermostat (120V Models)
Thermal Cut-off to Blu/BLK Lead From
Control Thermostat (220V Two Wire
Models)
WHI to WHI Lead on
Power Cord (120V Models)
Thermal Cut-off to Red
from Power Connector
(220V Two Wire Models)
Test Procedures:
1. Disconnect the brewer from the power source.
2. Disconnect the thermal cut-off from the tank
heater and the red wire from the power connector.
3. Check for continuity across the thermal cut-off
terminals with an ohmmeter.
If continuity is present as described, the thermal cutoff is operating properly.
If continuity is not present as described, replace the
thermal cut-off.
4.
5.
FIG. 10 TANK HEATER TERMINALS
P1254
Disconnect the thermal cut-off from the tank
heater and blue/black from the control thermostat.
Check for continuity across the thermal cut-off
terminals with an ohmmeter.
If continuity is present as decribed, the thermal cut-off
is operating properly.
If continuity is not present as described, replace the
thermal cut-off.
THERMAL CUT-OFF - VPRA, VPSA
Removal and Replacement:
1. Disconnect the thermal cut-off from the tank
heater and the red wire from the power connector or the blue/black wire from the control thermostat.
2. Install new thermal cut-off.
3. Refer to Fig. 12 when reconnecting wires.
HI
NN
BU
OFF
FIG. 11 THERMAL CUT-OFF
FIG. 12 THERMAL CUT-OFF TERMINALS
P3448
Page 13
P1269
10053 011405
5. Remove both wires from the warmer element and
check the continuity across the two terminals on
the warmer element.
SERVICE (cont.)
WARMER ELEMENTS
Y
ONL
ERNLY
WAT O
INATER
UR W
PO IN
UR
To
d re
o
N n d
u
A o u o t ce
D uth se re th
is o r- m e
co ri s o ri
n ze erv ve sk
n d ic o
ec s
r o
t erv ea op f e
b
p
o ic le en lec
w e p
er p a co tric
b ers rts ve s
efo
o in r. ho
ck
re nn sid
,
se el e
rv on .
ic ly
in .
g
.
PO
If continuity is present as described, reconnect the
wires on the warmer element.
If continuity is not present as described, replace the
warmer element.
Removal and Replacement:
1. Remove the three #4-40 screws securing the
warmer assembly to the brewer.
2. Lift the warmer assembly from the brewer.
3. Disconnect the two wires from the warmer element terminals.
4. Remove the two #8-32 nuts securing the warmer
element to the warmer plate.
5. Securely install new warmer element.
6. Reconnect the two wires to warmer element terminals.
7. Securely install warmer assembly on the brewer.
8. Refer to Fig. 14 when reconnecting the wires.
P3447
FIG. 13 WARMER ELEMENT
Location:
The warmer elements are located under the
warmer plates.
WHI /RED, VIO or BRN/BLK
to ON/OFF Switch
Test Procedures:
1. Disconnect the brewer from the power source.
2. Use the white to the power cord or red wire to the
power connector and the white/red, violet or
brown/black wire on the "ON/OFF" switch.
3. Check voltage across the white or red and white/
red, violet or brown/black with a voltmeter with
the "ON/OFF" switch in the "ON" position. Plug-in
the brewer to the power source. The indication
must be:
a) 120 volts ac for two wire 120 volt models.
b) 220 volts ac for two wire 220 volt models.
4. Disconnect the brewer from the power source.
WHI to WHI Lead on Power Cord
(120V Brewers)
RED to Power Connector
(220V Brewers)
FIG. 14 WARMER ELEMENT TERMINALS
P1255
If voltage is present as described, proceed to #5.
If voltage is not present as described, refer to wiring
diagrams and check brewer wiring harness.
Page 14
10053 011405
SCHEMATIC WIRING DIAGRAM VPR
(Models without Lighted switches)
GREEN
L1
SW. & THERMOSTAT
BLK
LIMIT
THERMOSTAT
BLU/BLK
BLK
1320W
N
WHI
TANK HEATER
50W
WHI
WHI
"KEEP WARM" HEATER
IND
ON/OFF
SWITCH
WHI
WHI/RED
100W
WHI/RED
BLK
IND
ON/OFF
SWITCH
VIO
BLK
WHI
LOWER WARMER
100W
VIO
WHI
WHI
UPPER WARMER
120 VOLTS A C
2 WIRE
SINGLE PHASE
60 HZ
10050.0000D 1/97 © 1988 BUNN-O-MATIC CORPORATION
SCHEMATIC WIRING DIAGRAM VPR
(Models with Lighted switches)
GREEN
L1
LIMIT
THERMOSTAT
SW. & THERMOSTAT
BLK
BLU/BLK
WHI
BLK
TANK HEATER
WHI
ON/OFF
SWITCH
WHI
WHI
LOWER WARMER
ON/OFF
SWITCH
BLK
120 VOLTS A C
2 WIRE
SINGLE PHASE
60 HZ
WHI
"KEEP WARM" HEATER
WHI/RED
BLK
N
WHI
WHI
VIO
UPPER WARMER
33769.0000A 02/01 © 2001 BUNN-O-MATIC CORPORATION
Page 15
10053 073001
SCHEMATIC WIRING DIAGRAM VPS
(Models without Lighted switches)
GREEN
L1
BLK
LIMIT
THERMOSTAT
BLU/BLK
BLK
WHI
50W
SW. & THERMOSTAT
1320W
N
WHI
TANK HEATER
WHI
"KEEP WARM" HEATER
IND
ON/OFF
SWITCH
WHI/RED
WHI
100W
WHI/RED
BLK
IND
ON/OFF
SWITCH
VIO
WHI
100W
VIO
BLK
IND
ON/OFF
SWITCH
WHI
UPPER WARMER
BRN/BLK
WHI
100W
BRN/BLK
BLK
WHI
LOWER LEFT WARMER
WHI
LOWER RIGHT WARMER
120 VOLTS A C
2 WIRE
SINGLE PHASE
60 HZ
10049.0000C 1/97 © 1988 BUNN-O-MATIC CORPORATION
SCHEMATIC WIRING DIAGRAM VPS
(Models with Lighted switches)
L1
SW. & THERMOSTAT
BLK
N
GREEN
LIMIT
THERMOSTAT
BLU/BLK
BLK
WHI
TANK HEATER
WHI
WHI
ON/OFF
SWITCH
"KEEP WARM" HEATER
WHI
WHI/RED
BLK
WHI
LOWER LEFT WARMER
ON/OFF
SWITCH
WHI
VIO
BLK
UPPER WARMER
ON/OFF
SWITCH
BLK
WHI
WHI
BRN/BLK
WHI
LOWER RIGHT WARMER
120 VOLTS A C
2 WIRE
SINGLE PHASE
60 HZ
10049.0001A 08/04 © 2004 BUNN-O-MATIC CORPORATION
Page 16
10053 011405
SCHEMATIC WIRING DIAGRAM
VPSA GRN/YEL
L1
L2
IND
BLK
RED
THERMAL
CUT-OFF
SW. & THERMOSTAT
1850W
BLU/BLK
BLK
THERMAL
CUT-OFF
RED
TANK HEATER
50W
WHI
ON/OFF
SWITCH
WHI/RED
RED
100W
WHI/RED
BLK
ON/OFF
SWITCH
IND
ON/OFF
SWITCH
VIO
RED
100W
RED
UPPER WARMER
IND
BRN/BLK
RED
100W
BRN/BLK
BLK
RED
LOWER LEFT WARMER
VIO
BLK
WHI
"KEEP WARM" HEATER
IND
RED
LOWER RIGHT WARMER
220 VOLTS A C
2 WIRE
SINGLE PHASE
SCHEMATIC WIRING DIAGRAM
VPRA GRN/YEL
L1
L2
IND
BLK
RED
SW. & THERMOSTAT
THERMAL
CUT-OFF
1850W
BLU/BLK
BLK
THERMAL
CUT-OFF
RED
TANK HEATER
50W
WHI
ON/OFF
SWITCH
WHI/RED
RED
100W
WHI/RED
BLK
ON/OFF
SWITCH
BLK
WHI
"KEEP WARM" HEATER
IND
IND
RED
LOWER WARMER
VIO
RED
100W
VIO
RED
UPPER WARMER
220 VOLTS A C
2 WIRE
SINGLE PHASE
Page 17
10053 011405
Download PDF

advertising