Treadmill Elegant+ Console
Entering Engineering Mode
Plug in the treadmill, turn on the power switch, stand on the side rails and insert the
safety key. Wait for the console to start up, about 1 minute. Press and hold the incline up
and speed down buttons at the same time for 3-5 seconds. When the console enters
Engineering Mode, you can release the buttons.
ABOUT
The ABOUT page shows information that is useful for a Service Provider and Dealer. Do
not press the PRODUCTION button on the bottom left side of the screen unless you are an
authorized Service Provider or Dealer instructed to do so by Vision Fitness.
SETTINGS
1. Press the SETTINGS tab on the left side of the screen. Press the setting you
would like to change and make your selection with the buttons that appear on the
right side of the screen.
a. MACHINE TYPE
b. MODEL TYPE
c. ENERGY SAVER
d. MIN INCLINE ADC – This should only be adjusted by an authorized
Service Provider or Dealer instructed to do so by Vision Fitness.
e. MAX INCLINE ADC – This should only be adjusted by an authorized
Service Provider or Dealer instructed to do so by Vision Fitness.
f. MIN RPM – This should only be adjusted by an authorized Service
Provider or Dealer instructed to do so by Vision Fitness.
g. MAX RPM – This should only be adjusted by an authorized Service
Provider or Dealer instructed to do so by Vision Fitness.
h. CURRENT INCLINE ADC – This is not an adjustable setting.
i. FIRST BOOT – This should only be adjusted by an authorized Service
Provider or Dealer instructed to do so by Vision Fitness.
j. PROGRAM SPEED – This should only be adjusted by an authorized
Service Provider or Dealer instructed to do so by Vision Fitness.
DEFAULT
1. Press the DEFAULT tab on the left side of the screen. Press the default you
would like to change and make your selection with the buttons that appear on the
right side of the screen.
a. MAX WORKOUT TIME
b. DEFAULT WORKOUT TIME
c. PAUSE TIME
d. WARM-UP TIME
e. COOL-DOWN TIME
f. DEFAULT AGE
g. DEFAULT GENDER
1| Revision date: 5/20/2015 | Revised by: EM
h. DEFAULT VOLUME
i. DEFAULT TARGET HEART RATE
j. BRIGHTNESS
k. VA MESSAGES
l. VA MUSIC
2. Pressing RESTORE on the bottom right side of the screen will reset all
DEFAULTS to the factory settings. This should only be performed by a n
authorized Service Provider or Dealer instructed to do so by Vision Fitness.
REGION
1. Press the REGION tab on the left side of the screen. Press the output you would
like to change and make your selection with the buttons that appear on the right
side of the screen.
a. DATE
b. TIME
c. LANGUAGE
d. UNITS
TEST
1. Press the TEST tab on the left side of the screen. Press the option you would
like to test with the buttons that appear on the right side of the screen.
a. DISPLAY TEST – Follow the instructions on screen to complete the test.
b. KEYPAD TEST – Press each of the buttons on the key pad to test.
c. AUDIO TEST – Press to hear a tone from the speakers.
d. HARDWARE TEST – This should only be adjusted by an authorized
Service Provider or Dealer instructed to do so by Vision Fitness. Changing
a setting should cause the belt and / or the incline motor to operate.
i. RPM – Allows a technician to test the RPM sensor.
ii. HEART RATE – Hold onto the grip pulse contacts or use a Polar®
chest strap
iii. INCLINE – Allows a technician to test an incline motor.
ERROR LOG
Press the ERROR LOG tab on the left side of the screen. If an error code is detected, it will
be logged here.
SERVICE LOG
Press the SERVICE LOG tab on the left side of the screen. A Service Provider or Dealer
may use this feature to log any service that has been performed.
Exiting Engineering Mode
Press the HOME button at the top left side of the screen to exit Engineering Mode and
return to the main screen.
2| Revision date: 5/20/2015 | Revised by: EM
Bike/Elliptical Elegant+ Console
Entering Engineering Mode
Plug in the bike or elliptical. Wait for the console to start up, about 1 minute. Press and
hold the resistance up and resistance down buttons at the same time for 3-5 seconds.
When the console enters Engineering Mode, you can release the buttons.
ABOUT
The ABOUT page shows information that is useful for a Service Provider and Dealer. Do
not press the PRODUCTION button on the bottom left side of the screen unless you are an
authorized Service Provider or Dealer instructed to do so by Vision Fitness.
SETTINGS
1. Press the SETTINGS tab on the left side of the screen. Press the setting you
would like to change and make your selection with the buttons that appear on the
right side of the screen.
a. MACHINE TYPE
b. MODEL TYPE
c. ENERGY SAVER
d. FIRST BOOT – This setting should only be adjusted by an authorized
Service Provider or the Dealer instructed to do so by Vision Fitness.
e. PROGRAM SPEED – This setting should only be adjusted by a
Service Provider or the Dealer instructed to do so by Vision Fitness.
DEFAULT
1. Press the DEFAULT tab on the left side of the screen. Press the default you
would like to change and make your selection with the buttons that appear on the
right side of the screen.
a. MAX WORKOUT TIME
b. DEFAULT WORKOUT TIME
c. PAUSE TIME
d. WARM-UP TIME
e. COOL-DOWN TIME
f. DEFAULT AGE
g. DEFAULT WEIGHT
h. DEFAULT GENDER
i. DEFAULT VOLUME
j. DEFAULT TARGET HEART RATE
k. BRIGHTNESS
l. VA MESSAGES
m. VA MUSIC
2. Pressing RESTORE on the bottom right side of the screen will reset all
DEFAULTS to the factory settings. This should only be performed by an
authorized Service Provider or Dealer instructed to do so by Vision Fitness.
3| Revision date: 5/20/2015 | Revised by: EM
REGION
1. Press the REGION tab on the left side of the screen. Press the output you would
like to change and make your selection with the buttons that appear on the right
side of the screen.
a. DATE
b. TIME
c. LANGUAGE
d. UNITS
TEST
1. Press the TEST tab on the left side of the screen. Press the option you would like
to test with the buttons that appear on the right side of the screen.
a. DISPLAY TEST – Follow the instructions on screen to complete the test.
b. KEYPAD TEST – Press each of the buttons on the key pad to test.
c. AUDIO TEST – Press to hear a tone from the speakers.
d. HARDWARE TEST
i. RPM – Allows a technician to test the RPM sensor.
ii. HEART RATE – Hold onto the grip pulse contacts or use a Polar®
chest strap
iii. ECB COUNTS – Allows a technician to test the ECB motor.
ERROR LOG
Press the ERROR LOG tab on the left side of the screen. If an error code is detected, it will
be logged here.
SERVICE LOG
Press the SERVICE LOG tab on the left side of the screen. A Service Provider or Dealer
may use this feature to log any service that has been performed.
Exiting Engineering Mode
Press the HOME button at the top left side of the screen to exit Engineering Mode and
return to the main screen.
4| Revision date: 5/20/2015 | Revised by: EM