Laboratory Glassware Washer G 7883

Operating Instructions
Laboratory Glassware
Washer
G 7883
To prevent accidents
and machine damage
read these instructions
before
installation or use.
More user manuals on ManualsBase.com
UV
M.-Nr. 05 893 860
Contents
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Description of the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Guide to the lab washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Opening and closing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting the water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Filling the salt reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Salt indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Adding rinse aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Setting the rinse aid dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Adding neutralizing agent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Adding detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Adjusting the upper basket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Program guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Turning on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Starting a program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Changing a program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
At the end of a program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Turning off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Canceling a program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Programming special functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Machine care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Trouble shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Water inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
2
More user manuals on ManualsBase.com
IMPORTANT SAFETY INSTRUCTIONS
Installation and Service
This appliance is only intended for
specialized applications. Only use
the appliance for its intended
purpose. Any other use, conversion
or modification is dangerous. The
manufacturer cannot be held
responsible for damages caused by
improper use of this machine.
This appliance complies with current
safety requirements. Improper use of
the appliance can lead to personal
injury and material damage.
Read all instructions before installing
or using this appliance.
Keep these operating instructions in
a safe place and pass them on to
any future user.
The machine should only be
installed, maintained and repaired
by a Miele authorized service
technician. Repairs by unqualified
persons could be dangerous.
Do not install the machine in an
area where a danger of explosion
or freezing may be present.
Be certain this appliance is
properly installed and grounded by
an authorized technician. To guarantee
the electrical safety of this appliance,
continuity must exist between the
appliance and an effective grounding
system. It is imperative that this basic
safety requirement be met. If there is
any doubt, have the electrical system of
the building checked by a qualified
technician. The manufacturer cannot be
held responsible for damage or injury
caused by the lack of or inadequacy of
an effective grounding system.
A damaged machine is dangerous;
turn off the machine at the main
power supply immediately and call the
Miele Technical Service Department.
Before servicing, disconnect the
power supply by either removing
the fuse or "tripping" the circuit breaker.
More user manuals on ManualsBase.com
3
IMPORTANT SAFETY INSTRUCTIONS
Use
Personnel operating the machine
should be trained regularly.
Children and untrained personnel must
not be allowed access to the machine
or its controls.
BURN AND SCALD HAZARD
This washer reaches very high
temperatures. Take care when
unloading the unit. Let baskets and
inserts cool before touching them. Any
water which may remain in containers
will be very hot and must be emptied
into the wash cabinet.
BURN HAZARD
The heating elements become
extremely hot during use. Do not touch
the heating elements during or directly
after the end of a program.
Take care when handling liquids
such as detergents, wetting agents
or neutralizing agents. These may
contain irritating or corrosive
ingredients. Do not use an organic
solvent in this washer, as an explosion
may occur. Wear protective gloves and
goggles. The manufacturer’s safety
conditions must be observed for all
chemical agents.
4
More user manuals on ManualsBase.com
Avoid inhaling powdered
detergent. If swallowed, it can
cause burning in the mouth and throat
or inhibit breathing.
Be careful when sorting items with
sharp pointed ends. If possible,
place the pointed end downwards.
The water in the machine must not
be used as drinking water.
Do not sit or lean on the open door.
Injury or machine damage could
result.
Never use a water hose or a high
pressure hose to clean the
machine or the areas surrounding it.
Only use cleaning agents
formulated for special processes
and approved by Miele for use with this
machine. Use of unsuitable cleaning
agents could adversely affect the
components of the machine.
IMPORTANT SAFETY INSTRUCTIONS
Pre-treatments with cleaning or
disinfecting agents can create
suds, as can certain rinsing agents. For
pre-treatment and / or cleaning, only
use low-sudsing detergents and
disinfecting agents which have been
approved by Miele. Suds can have an
adverse effect on the cleaning process.
When a chemical additive is
recommended on technical
application grounds (for example, with
a cleaning agent), this does not imply
that the manufacturer of the machine
takes responsibility for the effect of the
chemical on the material of the items
being cleaned. Please be aware that
changes in formulation, storage
conditions, etc, which may not be
published by the chemical producer,
can have a negative effect on the
cleaning result.
When using cleaning agents and
specialized products, it is essential
that the manufacturer’s instructions are
followed. Only use the product for the
application described by the
manufacturer to avoid any material
damage or the occurrence of strong
chemical reactions.
More user manuals on ManualsBase.com
The machine is designed only for
operation with water and additive
cleaning agents. Organic solvents must
not be used in the machine. An
explosion or machine corrosion could
occur with the use of organic solvents.
In critical applications where very
exact requirements must be met, it
is highly recommended that all the
relevant factors for the process, such
as cleaning agent, quality of water, etc.,
are discussed with Miele’s Application
Specialist.
The mobile units and special
inserts should only be used for
their specific applications.
Empty any containers or utensils
before arranging them in the
machine.
Do not allow any remains of acids
or solvents, particularly
hydrochloric acid or chloride solutions,
to get into the wash cabinet. The
presence of any solvents should be
minimized.
To prevent corrosion damage,
ensure that solutions or steam
containing hydrochloric acid do not
come into contact with the steel outer
casing of the machine.
5
IMPORTANT SAFETY INSTRUCTIONS
Accessories
Only genuine Miele parts or
accessories should be used with
the Laboratory Glassware washer. The
performance and safety of non-genuine
parts or accessories cannot be
guaranteed, and use of such parts or
items may void the machine warranty. If
you have specific questions about
machine options or accessories, please
call Miele.
Disposal of an appliance
When discarding a lab washer,
disconnect it from the power
supply, remove the door to the wash
cabinet and cut off the power cord.
For environmental and safety
reasons, ensure the machine is
completely drained of any residual
water and cleaning agent. (Observe
safety regulations and wear safety
goggles and gloves). Make appropriate
arrangements for the safe disposal of
the machine.
SAVE THESE
INSTRUCTIONS
6
More user manuals on ManualsBase.com
Description of the machine
The G 7883 is the "industry standard"
undercounter washer designed to
handle the vast majority of glassware
cleaning applications.
More user manuals on ManualsBase.com
7
Guide to the lab washer
a "On/Off" button
j "Add liquid detergent" indicator *
b "Door" button
k "Add rinse aid" indicator
c Display
l "Add neutralizing agent" indicator
d "Display" indicator
m "Recharge Softener" indicator
e "Drying" indicator
n "Check fill/drain" indicator
f "Start" indicator
o Program sequence display
g "Start" button
p Program selector
h "Drying" button
* (only with optional DOS-Module)
i "Display" button
(toggles between the elapsed
time, active wash blocks and actual
temperature displays)
8
More user manuals on ManualsBase.com
Guide to the lab washer
a Connection for optional DOS-Module
d Powdered detergent dispenser
b Filter combination
e Rinse aid reservoir
(with dosage selector)
c Salt reservoir
(water softener)
More user manuals on ManualsBase.com
f Rinse aid level indicators
9
Opening and closing the door
Electric door lock
To cancel a program
The machine is equipped with an
electric door lock. The door can only be
opened when the electrical supply to
the machine is turned on, and the
"On/Off" button is pressed.
If a program has to be canceled in an
emergency, e.g. the program has been
interrupted due to a fault, the door will
have to be opened manually.
To open the door
^ Press the "Door" button in as far as it
will go. At the same time, grip the
handle and open the door.
After the first intake of water, the door
remains locked and cannot be opened
until the end of the program (except
during the "Rinse" and "Drain"
programs). The machine can be
programmed to open during the
"Drying" program, if desired.
Do not touch the heating elements.
They remain hot for some time after
the end of the program and can
cause burns.
To close the door
^ Lift the door upwards and push it
until it clicks shut. Do not press the
release catch while shutting the door.
10
More user manuals on ManualsBase.com
^ Turn the program selector to the
"Stop" f position. The program is
canceled after approximately
2 seconds.
Opening and closing the door
To open the door with the
emergency release
The emergency release should only be
used when the door cannot be opened
normally, e.g. in the event of a power
failure.
^ Turn the program selector to "Stop"
f.
^ Press the "On/Off" button to turn the
machine off.
^ Take precaution against pressure
wave release (rapid opening of the
door).
^ Pull the emergency release cable
(located at the bottom of the machine
behind the service panel) downwards
to open the door.
The door latch will reset after the
emergency cable has been activated.
More user manuals on ManualsBase.com
11
Water softener
Before using the machine for the first
time, the water softener should be
programmed. The water needs to be
softened to avoid calcium deposit
buildup on the items being cleaned and
in the machine itself.
To ensure a steady supply of soft water:
1. Make sure the water softener is
programmed correctly.
The softener contains settings from
1 - 60 gr/gal or 20 - 1080 ppm.
2. The salt reservoir must be filled with
reactivation salt.
(If the water hardness level is below
4 gr/gal [70 ppm]), the reservoir
does not need to be filled.)
The machine is set at the factory for a
water hardness level of 19 gr/gal
(340 ppm).
12
More user manuals on ManualsBase.com
Your local water authority will advise
you on the water hardness in your
area. If the water supply is harder or
softer than the factory setting
(including below 4 gr/gal or
70 ppm), the setting will need to be
changed. See "Setting the water
softener".
Water softener
Settings
Settings
1 - 30
gr/gal
1 - 30
ppm
CaCO3
Settings
31 - 60
gr/gal
31 - 60
ppm
CaCO3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19 *)
20
21
22
23
24
25
26
27
28
29
30
20
40
50
70
90
110
130
140
160
180
200
220
230
250
270
290
310
320
340
360
380
400
410
430
450
470
490
500
520
540
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
560
580
590
610
630
650
670
680
700
720
740
760
770
790
810
830
850
860
880
900
920
940
950
970
990
1010
1030
1040
1060
1080
*) factory setting
More user manuals on ManualsBase.com
13
Water softener
Setting the water softener
^ Turn off the machine with the "On/Off"
button.
^ Turn the program selector to the
"Stop" f position.
^ Press and hold the "Start" 6 and
"Display" ß buttons at the same
time. Turn the machine on with the
"On/Off" button.
The current program status "P..." will
appear in the display.
The "Fill/Drain" indicator will
illuminate.
The first time the water softener is set
the "Recharge Softener" light will
illuminate. This light will also illuminate
after restoring the factory settings, see
"Programming special functions".
^ Press the "Drying" 0 button once.
"E01" (programming level 1) will
appear in the display.
^ Turn the program selector one switch
position clockwise (1 o’clock
position).
The number "19" will appear in the
display (this indicates the factory
water hardness setting in gr/gal,
equivalent to 340 ppm).
^ Press the "Display" ß button as
many times as necessary, or hold it in
until the required value (hardness
level in gr/gal) appears in the display.
Once the number "60" has been
reached, the counter will begin again
at "0".
^ Press the "Start" 6 button. "SP" will
appear in the display.
^ Press the "Start" 6 button again.
14
More user manuals on ManualsBase.com
The setting will now be stored in
memory. The display will go out.
For future servicing, it is useful to make
a note of your water hardness level.
^ Enter your water hardness level here:
gr/gal
or
ppm
^ If your water is already soft and you
would like to deactivate the water
softener, set the hardness setting to
"0".
Water softener
Filling the salt reservoir
Only special, coarse-grained
reactivation salt* should be used in
this machine.
*Available from Miele’s Professional
Customer Service Department.
Please see back page for more
information.
Do not use other types of salt, e.g. table
salt, agricultural or gritting salt. These
could contain components which are
insoluble in water and could damage
the water softener. If in doubt, consult
Miele’s Professional Department.
The salt reservoir holds approx. 2.5 kg
of salt.
,Inadvertently filling the salt
reservoir with detergent will damage
the water softener.
Before filling, make sure that you are
using reactivation salt.
^ Remove the bottom basket from the
machine.
^ Unscrew the salt reservoir cap.
^ Place the funnel provided in place.
^ Carefully fill the reservoir with salt.
Displaced water will run out as it is
being filled.
^ Wipe any residual salt off the screw
threads on the socket.
^ Screw the cap on firmly.
^ Immediately after this step: Run the
"Rinse" program to remove any traces
of salt from the cabinet.
Note: There may be a delay before the
"Rinse" program starts due to the
reactivation of the water softener.
Before filling the salt reservoir with
reactivation salt for the first time fill it
with approx. 2.5 liters of water.
More user manuals on ManualsBase.com
15
Water softener
Salt indicator
When the salt reservoir is empty the
"Recharge Softener" indicator, b,
illuminates to remind you to fill the
reservoir.
Reactivation takes place automatically
during a program. The "Recharging"
indicator, a, illuminates while this is
occurring.
16
More user manuals on ManualsBase.com
Adding rinse aid
Rinse aid is not used in laboratory
glassware cleaning applications.
If rinse aid is required, the rinse aid
dosage must be activated with
assistance from Miele Technical
Service.
Rinse aid (e.g. Mielclear) is filled in the
storage container and dispensed
automatically. The storage reservoir
holds about 180 ml.
,Inadvertently filling the storage
^ Unscrew the cap.
reservoir with detergent will damage
the reservoir. Be sure only to use
rinse aid in the reservoir.
^ Pour rinse aid into the storage
container until the level indicator is
dark (see arrow in the illustration).
Use a funnel if necessary.
^ If the "Add Rinse aid" indicator
illuminates, the rinse aid storage
container needs to be refilled.
The storage container has a level
indicator on the interior of the door.
^ Open the door.
More user manuals on ManualsBase.com
^ Replace and tighten the cap. Clean
up any spilled rinse aid to prevent
oversudsing in the next wash.
^ Wait until the "Rinse" indicator on the
control panel illuminates before
adding any more rinse aid.
17
Adding rinse aid
Setting the rinse aid dosage
The dosage adjuster (see arrow in the
illustration) in the opening has settings
adjustable from 1 to 6 (1 - 6 ml).
It is preset to "3" (3 ml).
^ Use a flat headed screwdriver to turn
the dial to the correct setting.
If spots remain on the items, use a
higher setting.
If smearing or cloudy streaks appear,
use a lower setting.
18
More user manuals on ManualsBase.com
Adding neutralizing agent
Neutralizer (pH-level: acidic)
neutralizes detergent residue on the
surface of glassware and other items
being cleaned. It is automatically
dispensed in the rinse following the
wash step of a program.
The relevant program (see "Program
Guide" - DOS 3) cannot be started until
the dispensing system has been
primed. (This function can only be
canceled by a Miele Service Engineer.)
^ Place the container of neutralizer
(red) next to the machine.
^ Insert the siphon tube into the
container (observe the color code).
Setting the dosage and priming the
dispensing system
^ See "Programming special functions".
Important
The container should not be allowed
to empty completely.
When the "Add neutralizer" indicator
illuminates:
More user manuals on ManualsBase.com
19
Adding neutralizing agent
Setting the neutralizer dosage
and priming the neutralizer
dispensing system
First you need to access the
programming mode:
To access the programming mode
^ Turn the program selector to "Stop"
f.
^ Turn the machine off.
^ Press and hold the "Display" ß and
"Start" 6 button. At the same time
turn the lab washer on by the main
switch I-0.
The display shows the current
program status "P...".
The Fill/Drain indicator lights.
^ Press the "Drying" 0 button twice.
"E02" (programming level 2) appears
in the display.
The dosage is factory set to 0.10, you
may or may not be required to adjust it.
Set the dosage concentration
according to the detergent
manufacturer’s recommendations.
Example:
The manufacturer recommends a
neutralizer concentration of 0.3 %. The
value to be set is 0.30.
^ First access the programming level to
"E02".
^ Turn the program selector clockwise to
"Intensive".
The display shows the set dosage
concentration in % from 0.05 % 0.5 %.
^ Press and hold the "Display" ß
button until the desired value
appears.
The dosage time / dosage
concentration is saved.
^ Please note the dosage setting:
To store the settings
^ Press the "Start" 6 button. "SP"
appears in the display.
^ Press the "Start" 6 button again. The
change has been saved.
NOTE: This change will set the
neutralizer dispensing amount for all
wash programs that use neutralizer.
20
More user manuals on ManualsBase.com
Adding neutralizing agent
Priming the neutralizing system
^ Access the programming mode
level 2 (see "Adding neutralizer - To
access the programming mode").
^ Turn the program selector to
"Universal".
"do3" appears in the display.
^ Press the "Display" ß button.
The dosage system will be primed
automatically. The priming lasts
210 seconds and is complete when
"0" appears in the display.
^ Put the selector dial back to the
12 o’clock position and turn the
machine off with I-0.
After the dispensing system is primed,
then always:
^ Turn the unit back on.
^ Start the "Rinse" program, so that
after priming any agents in the wash
cabinet are diluted before being
drained away.
More user manuals on ManualsBase.com
21
Adding detergent
Only use cleaning agents formulated
for this machine. Do not use
detergents formulated for
domestic dishwashers.
Liquid detergent
It is recommended that mildly alkaline
liquid detergents be dispensed via the
optional DOS module.
Note
As a separate option, this machine can
also be fitted with a dispenser pump for
automatic liquid detergent dispensing
(DOS-Module G 60). This is connected
externally. Contact Miele for details.
The optional DOS Module G 60 is
supplied with its own installation and
connection instructions.
See "Programming special functions"
for information on priming the
dispensing system and setting the
dosage.
22
More user manuals on ManualsBase.com
Maintenance of the dispensing
system
To ensure trouble-free operation, the
following regular maintenance should
be carried out by a Miele approved
service technician.
Replace the dispensing hoses in the
DOS modules every 12-18 months.
Take care when handling liquid
agents and additives. These may
contain irritant or corrosive
ingredients.
Follow the manufacturer’s safety
instructions and relevant Health and
Safety procedures carefully.
Wear protective gloves and goggles.
Adding detergent
Powdered detergent
If you are using powdered detergent, it
must be placed in the detergent
container prior to every program,
except for "Rinse" and "Drain".
^ Add detergent to the compartment.
Dosage: approx. 3g/l, equivalent to
30 g per cleaning sequence.
^ Press the opening catch on the
container forward. The flap will spring
open. The flap is always open at the
end of a program.
More user manuals on ManualsBase.com
The manufacturer’s instructions
should be followed if they differ from
the above.
^ Close the dispenser lid.
23
Loading
The following instructions relate only to
basic preparation and loading of
glassware. There are additional
requirements for particular applications.
Note
Loading the machine
^ Do not place items to be cleaned
inside of other pieces, where they
may be concealed.
Remove debris
^ Load items so that water will cover all
surfaces. This ensures that they will
be properly cleaned.
Ensure that no acid or solvent
residues, especially hydrochloric
acid or chlorides, get into the wash
cabinet.
^ Hollow vessels, such as beakers,
graduated cylinders, flasks, etc.,
should be inverted and placed in the
correct inserts to ensure proper
cleaning. A cover net can be used to
reduce the risk of glass breakage
during the wash process.
^ Remove all agar residue from petri
dishes.
^ Petri dishes and similar items should
be placed in the correct insert with
the soiled side facing center.
^ Remove blood clots and residue from
test tubes, etc.
^ Pipettes should be placed with the
narrow end pointing down.
^ Remove all stoppers, corks, labels,
sealing wax residue, etc.
^ Deep-based items should be placed
at an angle to allow water to run off
easily.
^ Empty all glassware before loading
into the machine.
^ Tall, narrow pieces should be placed
in the center of the basket for best
water coverage.
^ The spray arms must not be blocked
by items that are too tall or hang
through baskets. Check clearance by
manually rotating the spray arms.
24
More user manuals on ManualsBase.com
Loading
Important:
Make sure that the spring adapter for
the water connection engages correctly
when a basket or injector unit is
inserted into the machine. It must be
4 - 5 mm higher than the water
connection inlet in the machine. If this is
not the case, adjust the adapter by
performing the following steps:
^ Loosen the locking ring.
^ Push up the adapter 4 - 5 mm and
tighten the locking ring.
Select baskets and inserts which are
appropriate for the application.
Please contact Miele’s application
specialist for advice:
1-800-991-9380
More user manuals on ManualsBase.com
25
Loading
Loading examples
O 188 Upper basket
For various inserts.
O 187
Injector wagon
(Upper basket) For direct injection of
narrow necked glassware,
34 injectors,160 mm high.
E 350
Injector wagon
For narrow necked glassware,
15 injectors, 160 mm high;
18 injectors, 220 mm high.
26
More user manuals on ManualsBase.com
Loading
U 874 Lower basket
E 106
For various inserts.
Stainless steel half insert with 28 spring
hooks in 2 different heights for various
glassware, e.g. narrow necked flasks,
graduated cylinders, medicine bottles,
etc.
E 109
Stainless steel half insert to
accommodate 21 beakers up to 250 ml,
Erlenmeyer flasks, round flasks etc.
More user manuals on ManualsBase.com
27
Loading
Adjusting the upper basket
The upper basket can be adjusted
above and below the middle position
by 2 cm.
Example:
Upper basket O 188/1 and lower
basket U 874
(measurements do not include inserts)
Upper
basket
position
Upper basket
height
Lower basket
height
cm
cm
inches
15.5
1
6 /8"
28.5
11 1/4"
Middle
17.5
6 7/8"
26.5
10 7/16"
Lower
19.5
7 11/16"
24.5
9 5/8"
Upper
inches
To adjust the upper basket:
^ Pull out the upper basket, lift from the
runners and remove.
^ Unscrew the roller bearings on both
sides of the basket with a wrench
and reposition as required.
28
More user manuals on ManualsBase.com
Program guide
Program
Program cycle
PreWash
Custom
Main
wash 1
1)
Main
wash 2
Rinse
Rinse
1)
Final
rinse 1
Final
rinse 2
Drying
(Optional
function)
1) 2)
1) 2)
X
DOS 1 DOS 3
80°C/3’
1’
X
X
DI
75/1’
X DI
X
X
DOS 3
50°C/1’
DOS 1 DOS 3
75°C/3’
1’
X
DI
X
DI
X DI
70°C/1
min
X
ORGANICA
DOS 1 DOS 1 DOS 3
65°C/3’ 85°C/3’ 1 min
X
X
DI
X DI
80°C/1’
X
STANDARD
DOS 1 DOS 3
75°C/3’
1’
X
DI
X DI
75°C/1’
X
INORGANICA
UNIVERSAL
X
DOS 1 DOS 3
80°C/3’
1’
X
X
DI
X DI
75°C/1’
X
INTENSIVE
X
DOS 1 DOS 3
85°C/3’
1’
X
DI
X
DI
X DI
85°C/1’
X
PLASTIC
X
DOS 1 DOS 3
55°C/3’
1’
X
X
DI
X DI
55°C/1’
X
DRAIN
RINSE
X
X = Sections included in a program (with temperature/temperature holding time)
1)
Temperature or temperature holding time changeable (see "Programming special functions").
2)
DOS 2 = Rinse aid dosage possible (needs to be programmed by the Miele Technical Service).
DOS 3 = Neutralizer dosage
DI = distilled water
More user manuals on ManualsBase.com
29
Program guide
Program
Program cycle
Pre-Wash
varioTD
SPECIAL
93°C-10’
X
Thermal
Disinfection
and/or main
wash 1)
Rinse
Rinse
Final rinse
DOS 1
X
55°C/3’
DOS 3
X
1’
X
X
93°C/10’
DI
(X)
DOS 1
X
93°C/10’
DOS 3
X
1’
X
X
75°C/3’
DI
(X)
1) 2)
Drying
(Optional
function)
X = Sections included in a program (with temperature/temperature holding time)
1)
2)
30
Temperature or temperature holding time changeable (see "Programming special functions").
DOS 2 = Rinse aid dosage possible (needs to be programmed by the Miele Technical Service).
DOS 3 = Neutralizer dosage
DI = distilled water
More user manuals on ManualsBase.com
Operation
Turning on
^ Close the door.
^ Press the "On/Off" button.
When the program selector is at the
"Stop" f position, a point lights up in
the display.
Starting a program
^ Turn the program selector clockwise
or counterclockwise to the required
program.
The temperature of the first rinse of
the program selected (except for
"Pre-Wash" and "Drain") is shown in
the display. The "Start" indicator will
flash.
^ Select the "Drying" 0 function if
required (see "Drying").
^ Press the "Start" 6 button. The actual
temperature will appear in the
display.
The "Start" indicator will remain lit.
More user manuals on ManualsBase.com
Once the program has started, all other
programs are blocked. If the program
selector is turned to another program,
the values shown in the display will go
out. The values can be seen again if the
program selector is turned back to the
position of the program currently in
operation.
^ During a program, the "Display" ß
button can be used to toggle
between the elapsed time, the active
wash block and the actual
temperature.
Wash block codes
1 = Pre-Rinse 1
2 = Pre-Rinse 2
3 = Main Wash 1
4 = Main Wash 2
5 = Chemical Disinfection
6 = Interim rinse 1
7 = Interim rinse 2
8 = Interim rinse 3
9 = Interim rinse 4
10 = Final rinse 1
11 = Final rinse 2
12 = Drying TA
13 = Drying
31
Operation
Drying
At the end of a program
"Drying" 0 may be selected as an
additional feature once a program has
been selected (except in the "Rinse"
and "Drain" programs).
^ The "Complete" indicator in the
program sequence display
illuminates, and the "Start" 6
indicator will go out.
Drying is phased over 10 minutes. The
total running time of the program
lengthens accordingly.
^ A "0" will appear in the middle of the
display. All indicators will come on
and go out in sequence.
Changing a program
A wrongly selected program may be
changed as described below.
If the "Start" 6 button has not yet
been pressed
^ Turn the program selector to the
required program.
^ Select the "Drying" 0 function if
required (see "Drying").
^ Press the "Start" 6 button.
If "Start" 6 has already been
pressed, see "Canceling a program".
32
More user manuals on ManualsBase.com
^ Simultaneously, a buzzer will sound
for approximately 30 seconds
(standard setting). The buzzer
function can be changed (see
"Programming special functions").
Use the "Display" ß button to view the
total running time or temperature of a
program.
Turning off
^ Press and release the "On/Off" button.
Note:
The machine is fitted with an electric
door lock. The door can only be
opened if the "On/Off" button is pressed
(see "Opening and closing the door").
Operation
Canceling a program
^ Turn the program selector to the
"Stop" f position (the program will
stop after approximately 2 seconds).
^ Open the door.
,Caution: Water and items in the
machine may be hot. Danger of
burning or scalding.
^ Arrange the load securely. Wear
protective gloves where necessary,
and observe appropriate health and
safety regulations relating to
infectious diseases.
^ Replenish powder detergent, if
necessary.
^ Close the door.
^ Select and start the "Drain" program.
^ When finished with "Drain", select and
restart the desired program.
More user manuals on ManualsBase.com
33
Programming special functions
For future servicing, please
document any alterations to the
standard factory settings.
General note
Program selector positions that have
not been allocated to a function are
indicated in the middle part of the
display by a bar (-).
The programming level is called up via
the "Stop" f position.
Accessing the programming
level
Before performing any of the special
functions that follow, the programming
mode of the labwasher controller needs
to be accessed.
^ Turn the program selector to "Stop"
f.
^ Turn the machine off.
^ Press and hold the "Display" ß and
"Start" 6 buttons. At the same time,
turn the machine on with the "On/Off"
button.
^ The display will show the current
program status "P...".
The "Fill/Drain" indicator will
illuminate.
^ Press 0 twice. "E02" (programming
level 2) appears in the display.
34
More user manuals on ManualsBase.com
Programming special functions
1. Setting the dosage
concentration and priming the
dosage system
Before performing any of the
following special functions, the
programming mode of the controller
needs to be accessed. See
"Accessing the programming level".
1.1 DOS 1 (Liquid detergent)
by DOS unit G 60 or C 60 (Optional
accessory)
1.1.1 Setting the dosage
concentration
^ Access the programming level E02 of
the controller (see "Accessing the
programming level").
Set the dosage concentration
according to the detergent
manufacturer’s recommendations.
^ Turn the program selector to
"Inorganica". The display shows
either the dosage time in seconds
(for powdered detergent) or the set
dosage concentration in % (for liquid
detergent).
"10" = Dosage time of 10 seconds for
powdered detergent, or
"0.10" - "0.80" = 0.1 % - 0.8 %
concentration for liquid detergent
dosage.
^ Press and hold "Display" ß until the
desired value appears.
^ Please note the dosage setting here:
^ Press the "Display" ß button.
The dosage system will be primed
automatically. The priming is done if
the display shows "0".
Example:
The manufacturer recommends a
detergent concentration of 0.5%.
The value to be set is 0.50.
More user manuals on ManualsBase.com
35
Programming special functions
a) If the dosage concentration is set:
b) If the system is primed only (e.g.
because the dosage system was
completely empty):
^ Turn the program selector to
"Custom". "do1" appears in the
display.
^ Select programming level "E02"
(see "Accessing the programming
level").
^ Press the "Display" ß button.
The dosage system will be primed
automatically. The priming is done if
the display shows "0".
^ Turn the program selector to
"Custom".
"do1" appears in the display.
1.1.2 Priming the detergent system
To store the settings:
^ Press the "Start" 6 button. "SP"
appears in the display.
^ Press the "Start" 6 button again. The
change has been saved.
^ Press the "Display" ß button.
The dosage system will be primed
automatically. The priming is
complete if the display shows "0".
^ Turn the machine off with the "On/Off"
button.
When the dispensing system is
primed, always:
^ Run the "Rinse" program afterwards
to remove any detergent or
neutralizer residues in the wash
chamber.
36
More user manuals on ManualsBase.com
Programming special functions
1.2.2 Priming the neutralizer system
Before performing any of the
following special functions, the
programming mode of the controller
needs to be accessed.
1.2 DOS 3 (Neutralizer)
1.2.1 Setting the dosage concentration
The dosage is factory set at 0.10, you
may or may not be required to adjust it.
a) If the dosage concentration is set:
^ Turn the program selector to
"Universal". "do3" appears in the
display.
^ Press "Display" ß.
The dosage system will be primed
automatically. The priming is complete
when "0" appears in the display.
To store the settings:
Set the dosage concentration
according to the detergent
manufacturer’s recommendations.
Example:
The manufacturer recommends a
neutralizer concentration of 0.3 %.
The value to be set is 0.30.
^ First access the programming level
E02.
^ Turn the program selector clockwise to
"Intensive". The display shows the set
dosage concentration
in % from 0.05 % - 0.5 %.
^ Press and hold "Display" ß until the
desired value appears.
^ Please note the dosage setting:
To store the settings:
^ Press the "Start" 6 button. "SP"
appears in the display.
^ Press the "Start" 6 button again. The
setting has been saved.
NOTE: This change will set the
neutralizer dispensing amount for all
wash programs that use neutralizer.
More user manuals on ManualsBase.com
^ Press the "Start" 6 button. "SP"
appears in the display.
^ Press the "Start" 6 button again. The
setting has been saved.
b) If the system is primed only (e.g.
because the dosage system was
completely emptied):
^ Select programming level 2
(see "Accessing the programming
level").
^ Turn the program selector to "Universal".
"do3" appears in the display.
^ Press "Display" ß.
The dosage system will be primed
automatically. The priming is
complete when "0" appears in the
display.
^ Turn the machine off with the "On/Off"
button.
When the dispensing system is
primed, always:
^ Run the "Rinse" program afterwards to
remove any detergent or neutralizer
residues in the wash chamber.
37
Programming special functions
2. Changes in wash temperature
and / or temperature holding
time at "Main wash" (except
SPECIAL 93°C-10’ and "Final
rinse")
Any changes to the wash
temperature and/or the temperature
holding time should be recorded in
the appropriate section of the
"Program guide".
The factory setting of the cleaning and
final rinse temperature with temperature
holding time can be seen in the
"Program guide".
The cleaning and final rinse
temperature can be changed from 30
°C - 93 °C and 30 °C - 70 °C (programs
"Standard" and "Universal"),
respectively. The temperature holding
time can be changed from 1 to 15
minutes.
38
More user manuals on ManualsBase.com
^ Turn the program selector to "STOP"
f.
^ Turn the machine off.
^ Press and hold "Display" ß and
"Start" 6. At the same time, turn the
lab washer on with the "On/Off"
button.
The displays shows the current
program status "P...".
The "Fill/Drain" indicator will
illuminate.
Programming special functions
"Main wash" temperature
^ Main wash 1:
Press and hold the "Drying" 0
button until "E09" appears in the
display.
Main wash 2:
Press and hold the "Drying" 0
button until "E12" appears in the
display.
^ Turn the program selector to the
program to be changed. The current
value appears in the display after °C.
^ Press and hold "Display" ß until the
desired value appears in the display.
To store settings
"Main wash" temperature holding
time
^ Turn the program selector to "STOP"
f.
^ Main wash 1:
Press and hold "Drying" 0 until "E10"
appears in the display.
Main wash 2:
Press and hold "Drying" 0 until "E13"
appears in the display.
^ Turn the program selector back to the
program to be changed. The current
value appears in the display after
min.
^ Press and hold "Display" ß until the
desired value appears in the display.
^ Press the "Start" 6 button. "SP"
appears in the display.
To store settings
^ Press the "Start" 6 button again. The
change has been saved.
^ Press the "Start" 6 button. "SP"
appears in the display.
^ Press the "Start" 6 button again. The
change has been saved.
More user manuals on ManualsBase.com
39
Programming special functions
"Final rinse" temperature
^ Turn the program selector to "STOP"
f.
^ Final rinse 1:
Press and hold "Drying" 0 until "E22"
appears in the display.
Final rinse 2:
Press and hold "Drying" 0 until "E25"
appears in the display.
^ Turn the program selector back to the
program to be changed. The current
value appears in the display after °C.
^ Press and hold "Display" ß until the
desired value appears in the display.
To store settings
^ Press the "Start" 6 button. "SP"
appears in the display.
^ Press the "Start" 6 button again. The
change has been saved.
"Final rinse" temperature holding
time
^ Turn the program selector to "Stop"
f.
^ Final rinse 1:
Press and hold "Drying" 0 until "E23"
appears in the display.
Final rinse 2:
Press and hold "Drying" 0 until "E26"
appears in the display.
^ Turn the program selector back to the
program to be changed. The current
value appears in the display after
min.
^ Press and hold "Display" ß until the
desired value appears in the display.
To store settings
^ Press the "Start" 6 button. "SP"
appears in the display.
^ Press the "Start" 6 button again. The
change has been saved.
40
More user manuals on ManualsBase.com
Programming special functions
3. Setting the buzzer
A buzzer can be set to signal the
following:
– End of program = continuous buzzer
– Error = rhythmic buzz
– Timer to allow sampling of the last
final rinse water
= intervals of 3 short buzzes and
2 seconds break
^ Turn the program selector to "STOP"
f.
^ Turn the machine off.
^ Press and hold "Display" ß and
"Start" 6. At the same time, turn the
lab washer on with the "On/Off"
button.
The displays shows the current
program status "P...".
The "Fill/Drain" indicator lights.
^ Press "Drying" 0 4 times. "E04"
appears in the display.
^ Turn the program selector to
"Inorganica". A number between "20"
and "27" appears in the display.
"20" = Buzzer is turned off
"21" = End of program
(factory setting)
"22" = Error
"23" = Error and End of program
"24" = Test sample extraction
"25" = End of program and
Test sample extraction
"26" = Error and Test sample
extraction
"27" = All functions
(End of program, Error,
Test sample extraction).
^ Press and hold "Display" ß until the
desired value appears in the display.
^ Press the "Start" 6 button. "SP"
appears in the display.
^ Press the "Start" 6 button again. The
change has been saved.
^ Please note the changed setting:
To turn the buzzer off:
^ Turn the program selector to "STOP"
f or press the "Display" ß button.
More user manuals on ManualsBase.com
41
Programming special functions
4. Restoring the factory
settings
^ Turn the program selector to "STOP"
f.
^ Turn the machine off.
^ Press and hold "Display" ß and
"Start" 6. At the same time, turn the
lab washer on with the "On/Off"
button.
The displays shows the current
program status "P...".
The "Fill/Drain" indicator lights.
^ Press and hold "Drying" 0 until "E33"
appears in the display.
^ Turn the program selector to any
position (except "STOP").
The display shows either "00" or "PP".
"00" = factory setting; electronic was
not reprogrammed.
"PP" = electronic was reprogrammed.
^ If "PP" is displayed press "Display" ß
to change from "PP" to "00".
^ Press the "Start" 6 button. "SP"
appears in the display.
^ Press the "Start" 6 button again.
All factory settings are now restored.
42
More user manuals on ManualsBase.com
If the hardness level setting in the
water softener had been changed,
this will reset to the factory setting of
340 ppm (19 gr/gal). This will need
to be reset to suit the hardness level
in your area.
Changes in programs "Custom",
"Inorganica" and "Organica" cannot
be reset.
Machine care
Filter combination
,The machine must not be used
without all the filters in place. The
filters protect the circulation pump
from damage caused by foreign
objects.
Cleaning the fine, flat and micro-fine
filters
^ Remove the coarse filter.
^ Remove the fine filter (if fitted) from between the flat and the micro-fine filters.
The filter combination in the base of
the wash cabinet should be
inspected regularly and cleaned if
necessary.
Caution:
Watch out for sharp objects which
could cause injury.
Cleaning the coarse filter
^ To unscrew the micro-fine filter, grasp
the two tabs and turn counterclockwise twice.
^ Press the two tabs together. Remove
and clean the coarse filter.
^ Put the clean filter back in position
and press until it clicks in place.
^ Remove both filters together.
^ Clean the filters.
^ Replace the filter combination in
reverse order. The flat filter must lie
flat in the base of the wash cabinet.
More user manuals on ManualsBase.com
43
Machine care
Cleaning the non-return valve
and drain pump
The drain pump is located beneath the
non-return valve (see arrow).
If water has not been pumped away at
the end of a program, the drain pump
or the non-return valve may be blocked.
^ Turn off the washer.
^ Remove the filter combination from
the wash cabinet.
^ Before returning the non-return valve,
check that the drain pump is not
blocked. Spin the propeller several
times in both directions to check for
obstructions.
^ Tilt the locking clamp to the side.
^ Pull out the non-return valve and
rinse under running water.
44
More user manuals on ManualsBase.com
^ Carefully refit the non-return valve
and secure it with the locking clamp.
Refit and lock the filter in place.
For safety reasons the load should
be washed again.
Machine care
Cleaning the filters in the water
inlet
^ Replace filters and the seal. Make
sure they are sitting correctly.
Filters are incorporated in the screw
connection of the water inlet hose to
protect the water inlet valve. If these
filters become dirty, they need to be
cleaned, otherwise insufficient water
flows into the wash cabinet.
^ Reconnect the hose to the water inlet,
making sure that it goes back on
straight.
,The plastic housing of the water
connection contains an electrical
component. It must not be
submerged in water.
To clean the filters
^ Disconnect the machine from the
main electrical supply.
^ Turn off the water supply.
^ Unscrew the water inlet hose.
^ Open the water tap carefully.
If there is a leak, tighten the
connections.
Cleaning the control panel
^ The control panel should only be
cleaned with a damp cloth or a
suitable cleaner for use on plastic
materials.
,Do not use abrasive cleaners,
glass cleaners or all-purpose
cleaners! They will damage the
control panel.
Cleaning the front of the
machine
^ Use a cleaner suitable for the type of
material the machine front is fitted
with.
,Do not use detergents
containing ammonia or thinners.
^ Clean the large area filter, 1, and fine
filter, 2, replace with new filters, if
necessary.
More user manuals on ManualsBase.com
45
Trouble shooting
With the aid of the following guide, minor problems can be fixed without a service
call.
The Miele control unit includes a wide range of fault codes to indicate specific
errors. These fault codes are indicated on the display by a flashing F. . . (Ranging
from F1 up to F30.) If one of these codes appears, please contact the Miele
Technical Service Department at 1-800-991-9380 for assistance.
What if …
Possible fault
Fix
the machine does not
start?
The door is not
properly closed.
The fuse is defective
or the breaker has
tripped.
Close the door firmly.
"Fdo" appears in the
display.
Follow the instructions to prime
the dispensing system
(see "Programming special
functions DOS 1 - 1.1.2
Priming the detergent system"
and "DOS 3 - 1.2.2 Priming the
neutralizer system")
– Turn the program selector to
"Stop" f (the fault code
goes out).
– Press the "On/Off" button to
turn the machine off.
– Open the water valve or
clean the filters (see "Lab
washer care").
– Turn the machine on again
and reselect the program.
a few minutes after
starting a program, the
"Fill/Drain" indicator
flashes and the fault
code "F..E" appears in
the display?
46
– The water valves
are closed.
– The filters in the
water inlet hose
are dirty.
More user manuals on ManualsBase.com
Make sure the circuit breaker
has not tripped.
Trouble shooting
What if …
Possible fault
the wash cycle finishes – The drain hose is
too early, the "Fill/Drain"
kinked.
indicator flashes and
– The drain pump is
the fault code "F A"
blocked.
appears in the display?
water in the wash
cabinet is not heated,
the program sequence
lasts too long and the
following fault code
appears in the display:
"F01 - F03, F18, F19"?
This machine has a
resettable heater
limiter, which will
switch off the heater
in case of
over-heating. This
could be caused if
large articles cover
the heating elements,
or if the filters in the
wash cabinet are
blocked.
More user manuals on ManualsBase.com
Fix
– Turn the program selector to
"Stop" f (the fault code
goes out).
– Press the "On/Off" button to
turn the machine off.
– Remove any kinks in the
hose. Clean the drain pump
(see "Machine care").
– Turn the machine on, run the
drain program then restart
the original program (see
Operation").
– Remove the cause of the
fault.
– Remove the service panel
(see "Electrical connection").
– Press the reset button on the
temperature sensor on the
right side.
If this switch trips repeatedly,
contact the Miele Technical
Service Department before
further use. See back cover
for phone numbers.
47
Trouble shooting
What if …
Possible fault
I need to open the door
during a power failure?
the fault was caused by
a possible misfunction.
48
More user manuals on ManualsBase.com
Fix
– see "Opening and
closing the door."
– Turn the program
selector to "Stop" f
(the fault code goes
out).
– Press the "On/Off"
button to turn the
machine off.
– Turn the machine on
again and reselect the
program.
If there are further
difficulties, or if the fault
code "F..." appears in
the display, please
contact the Miele
Service Department. See
back cover for phone
numbers.
After Sales Service
In the event of a fault which you cannot
correct yourself please contact the
Miele Technical Service Department
U
1-800-991-9380
techserv@mieleusa.com
l
1-800-565-6435
service@miele.ca
Please quote the model of your
machine. This information can be found
on the machine’s front panel.
More user manuals on ManualsBase.com
49
50
More user manuals on ManualsBase.com
INSTALLATION INSTRUCTIONS
More user manuals on ManualsBase.com
Caring for the environment
Disposal of the packing
material
The protective packing materials are
environmentally safe and can be
recycled.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocation!
52
More user manuals on ManualsBase.com
Disposal of the appliance
Appliances contain materials which can
be recycled. Please contact your local
authorities about recycling in your area.
Ensure that the machine presents no
danger to children while being stored
for disposal. See "Important Safety
Instructions".
Installation
Please refer to the installation
diagram supplied with the machine.
,Furniture and fittings installed
near the machine must be of a
commercial standard (able to
withstand the effects of steam).
Installation options
– Free-standing
– Undercounter
The machine can be installed under a
continuous counter or sink drain. The
recess must be at least 60 cm wide,
60 cm deep and 82 cm high.
Positioning and securing the
machine
To ensure stability, the machine must be
aligned and screwed to the counter.
^ Open the door.
^ Secure the machine to the front edge
of the worktop using the screws to
the left and right of the front trim.
^ When not mounted undercounter,
floor mounting brackets must be
used.
Do not use silicone sealant to seal
the gaps between the machine and
any neighboring units. This will
hinder ventilation to the circulation
pump.
Steam Deflector (protects the
countertop)
Depending on the requirements for an
undercounter installation, a steam
deflector can be ordered from the Miele
Technical Service Department.
The underside of the countertop is
protected from steam damage by a
stainless steel plate.
More user manuals on ManualsBase.com
53
Installation
Removing the lid (if necessary)
If necessary, remove the lid from the
machine to make installation possible.
^ Open the door.
^ Remove the fixing screws on the left
and right sides using a phillipshead
screwdriver.
^ Pull the machine lid approx. 5 mm
forwards, lift it upwards and remove.
54
More user manuals on ManualsBase.com
Important for machines with steam
condenser (depending on model)
^ To prevent countertop damage by
steam, the supplied self adhesive
protective foil (25 x 58 cm) must be
placed underneath the countertop
near the steam condenser.
Plumbing
Water inlet
^ The machine must be connected to
the water supply in accordance with
local and national regulations.
^ The washer is constructed so it may
be connected to a supply without an
extra non-return valve, unless
required by code.
^ An acceptable water pressure (flow
rate) is 10 - 147 psi. However, the
recommended pressure is
25 - 60 psi.
If the water pressure is below 30 psi,
the fill time will take longer.
If the "Fill/Drain" fault code "F..E" is
displayed, contact the Technical
Service Department.
^ The machine is supplied to be
connected to a standard cold (coded
blue) or hot (coded red) water supply
to a maximum temperature of 158 °F
(70 °C.)
Connect the water intake hoses to the
cold and hot water faucets.
If no hot water supply is available, the
hot water intake hose with the red
marking needs to be connected to
cold water by a y-adapter.
^ Water valves with 3/4" male hose
thread are to be provided on site.
They should be easily accessible so
the water supply can be turned off if
necessary.
^ The inlet hoses are 5 ½ feet (1.7 m)
long, terminating in a 3/4" female hose
thread. The water inlet filters in the
threads must not be removed.
^ Large surface area filters are
enclosed in the kit supplied with the
machine.
Install these filters between the water
valve and the water inlet hose (see
illustration in "Machine Care/Cleaning
the filters in the water inlet"). The
large surface area filter for DI water is
made from stainless steel and can be
recognized by its matte surface.
For a DI water connection (H2O
pure), see the next page.
,Do not cut the inlet hose or
damaged it in any way.
^ See the supplied installation diagram.
More user manuals on ManualsBase.com
55
Plumbing
DI-Water connection
The machine comes with a standard
connection for a pressure-resistant
system. The recommended water
pressure (flow rate) is 25 - 60 psi
however, water pressure of 10 - 147 psi
is acceptable.
^ The DI pressure-tested hose (marked
"H2O pure") with a 3/4" hose thread
must be connected to the on-site
water valve for DI purified water.
If the DI water connection is not
used, the electronics needs to be
reprogrammed by a Miele technician.
The water intake hose remains at the
rear side of the machine.
56
More user manuals on ManualsBase.com
Plumbing
Drainage
^ The drainage system is fitted with a
non-return valve which prevents dirty
water from flowing back into the
machine via the drain hose.
^ The machine should preferably be
connected to a separate drainage
system onsite.
If separate drainage is not available
contact your Miele application
specialist for advice.
The onsite drain connection point
should be located between 1 ft.
(0.3 m) and 3 ft. (1 m) above the
lower edge of the machine.
If it is lower than 1 ft. (0.3 m), lay the
hose in a curve at a height of at least
1 ft. (0.3 m).
The drainage system must be able to
take a minimum drainage flow of
16 l/min.
^ The drain hose is approx. 5 ft. (1.5 m)
long, is flexible and has an internal
diameter of 7/8 in. (22 mm). It must
not be shortened. Hose clamps are
supplied for securing it in position.
^ A longer drain hose (up to 12 ft. [4 m]
long) is available to order from the
Miele Technical Service Department.
^ The drainage system must not
exceed 12 ft. (4 meters).
^ See the supplied installation diagram.
More user manuals on ManualsBase.com
57
Electrical connection
,All electrical work must be
performed by a qualified person in
accordance with local and national
safety regulations.
The machine comes equipped for
connection to a 208 V, 60 Hz, 3 phase
power supply. It is equipped with a 6 ft.
long, 12/4 AWG power cord, without a
plug. A plug, rated for the required
power which will fit the receptacle, is to
be supplied by the electrician doing the
installation. It should be connected to
the main power supply.
Voltage:
208 V, 3 phase
Frequency:
60 Hz
Rated Load:
6 kW
Circuit breaker:
3 x 20 A
Black : connect to L1 (hot)
Red:
connect to L2 (hot)
White: connect to L3 (hot)
Green: connect to GND (ground)
58
More user manuals on ManualsBase.com
It can be converted to use a single
phase power supply in accordance
with the conversion and wiring diagram.
The cord must be changed from a
12/4 AWG to a 10/3 AWG. Contact
Miele Technical Service for more
information
Voltage:
208 V, 1 phase
Frequency:
60 Hz
Rated Load:
6 kW
Circuit breaker:
2 x 30 A
^ Connection should be made via a
suitable isolator, with an "On/Off"
button easily accessible for servicing
work.
^ A damaged power cord must only be
replaced with a genuine Miele cord
by a Miele service technician.
WARNING
THIS APPLIANCE MUST BE
GROUNDED
Electrical connection
Grounding connection
^ The ground lead must be connected
to the screw connection point
(marked with the ground symbol 8) at
the back of the machine.
Removing the service panel
Disconnect the machine from the
main electrical supply.
^ Remove the fixing screws, a, from
the service panel.
^ Hold the service panel at both sides
and pull upwards.
^ Unscrew the facing, b. Remove the
plastic protective cap.
^ See the supplied installation diagram.
Re-assembling the service
panel
The machine must only be operated
with the voltage, frequency and
fusing shown on the data plate
located on the rear of the machine,
and on the plinth (behind the service
panel).
^ Refit the plastic protective cap,
facing and service panel in the
reverse order to which they were
removed.
The conversion diagram and the
wiring diagram is secured to the inner
side of the service panel.
More user manuals on ManualsBase.com
59
Technical data
English
7
Metric
5
Height:
33 /16" (32 /16")
85 (82) cm
Width:
23 5/8 "
60 cm
Depth:
23 5/8 "
60 cm
Voltage:
208 V
Power cord
approx. 5’ 11"
1.8 m
Water pressure (flow rate):
Recommended
25 - 60 psi
Acceptable
10 - 147 psi
1.72 - 4.13 bar
.7 - 10 bar
Cold or Hot water
connection
up to max. 158°F
70 °C
DI-Water connection
Recommended
Acceptable
25 - 60 psi
10 - 147 psi
1.72 - 4.13 bar
.7 - 10 bar
Delivery head:
min. 12"
max. 39 3/8"
0.3 m
1m
Drainage length:
max. 13’ 1"
4m
Water intake hose
approx. 5’ 7"
1.7 m
Drain hose:
approx. 4’ 7"
1.4 m
Noise level in dB (A):
Sound pressure level LpA
Free stand unit:
Built under counter:
60
At machine
64.8
62
More user manuals on ManualsBase.com
1 m (39 3/8") away
52.9
50.1
More user manuals on ManualsBase.com
61
62
More user manuals on ManualsBase.com
More user manuals on ManualsBase.com
63
All rights reserved / 1104
This paper has been bleached without the use of chlorine.
M.-Nr. 05 893 860 / 01