PIR Application Guide for the for VT7xxxX5000(X) Series

PIR Application Guide for the for VT7xxxX5000(X) Series thermostats
( Issue Date: November 5, 2007 – 028-xxxx Rx )
Product Overview
The VI-PIR Accessory covers with embedded Passive Infra-Red motion detector have been
specifically designed to work with all compatible VT7000 series thermostats. Thermostats
compatible with VI-PIR covers use the following part number assignments: VT7xxxxX5xxx(X). The
5 identifies the thermostat base thermostat has the necessary onboard polarized PIR connector
and functionality added.
When equipped with a VI-PIR accessory cover or a remote PIR sensor attached to one of the
remote input, a VT7000 series thermostat provides advanced active occupancy logic, which will
automatically switches occupancy levels from Occupied to Stand-By and Unoccupied as required
by local activity being present or not.
This advanced occupancy functionality provides advantageous energy savings during occupied
hours without sacrificing occupant comfort.
The range of applications covered with the PIR occupancy logic van be segmented in 2 important categories in terms of
functionality. Both use different settings and have different behaviours:
•
Hotel and lodging applications
•
Standard commercial applications
Typical applications that can be meet by the new PIR accessory covers range from:
•
Stand-alone lodging FCU applications
•
Networks lodging FCU applications fully integrated to a reservation system
•
Networked or stand-alone conference rooms
•
Networked or stand-alone classrooms units
•
Any commercial offices that have random occupancy schedules during occupied hours as dictated by the
function of the tenant
•
Or any controlled piece of HVAC equipment that may yield energy savings with the introduction of a new
automatic stand-by level of occupancy.
The additional following documentation is available on www.viconics.com
•
Detailed information on VT7200 series thermostat configuration, is available on document: LIT-VT7200-Exx
•
Integration information on VT7200 LON models, is available on document: ITG-VT7200-LON-Exx.doc
•
Integration information on VT7200 BACnet models, is available on document: ITG-VT7200-BAC-Exx.doc
•
Detailed information on VT7300 series thermostat configuration, is available on document: LIT-VT7300-Exx
•
Integration information on VT7300 LON models, is available on document: ITG-VT7300-LON-Exx.doc
•
Integration information on VT7300 BACnet models, is available on document: ITG-VT7300-BAC-Exx.doc
VI- PIR Cover Models Available
Viconics PIR Cover Part
Number
Description
Compatible with the
Following Thermostats
COV-PIR-FCU-C-5000
PIR cover with Commercial FCU interface
VT73x0X50xx(X)
COV-PIR-FCU-L-5000
PIR cover with Hotel/Lodging interface
VT73x5X50xx(X)
COV-PIR-HPUMP-5000
PIR cover for heat pump thermostats
VT76xxH50xx(X)x
COV-PIR-RTU-5000
PIR cover for roof-top thermostats
VT76xxX50xx(X)
COV-PIR-ZN-5000
PIR cover for zoning thermostats
VT7200X50xx(X)
10/16/07
028-6012
PIR Application Guide-E00.doc
www.viconics.com
sales@viconics.com
1
Configuration Parameters Associated with the Viconics PIR Accessory Covers
The following configuration parameters are specifically provided as standard on all VT7000 series thermostats. They
are associated with the advanced occupancy functionality introduced with the addition of a PIR cover or a remote PIR
sensor. These parameters will allow the installer to set the thermostat occupancy functions exactly as required by the
application.
Their functionality only becomes active if a PIR accessory cover is connected or one of the binary/digital input is
configured to use a remote PIR sensing device.
Configuration Parameter
Description of Configuration parameter
BI or DI input door setting
It is possible to configure some of the digital or binary inputs to effectively use
the advanced functions allowed by the installation of a door switch contact.
This function is mostly used with fan coil units in lodging applications
Default: None for no function used
Stand-by Heating Set point:
Default: 69 °F ( 20.5 °C )
When a door contact is used and configured, the Stand-By timer is no longer
active. The occupancy toggle between occupied and stand-by is now dictated
by both the door contact and the PIR cover.
• Movement detected by the PIR cover = Always occupied
• Door opens / closes detected by the door switch = Stand-by mode
This parameter sets the stand-by heating setpoint value.
The set value of this parameter should reside between the occupied and
unoccupied heating setpoints and make sure that the difference between the
stand-by and occupied value can be recovered in a timely fashion when
movement is detected in the zone.
Adjustable from 40 to 90 °F ( 4.5 to 32 °C ) in 0.5 degree increments.
This parameter sets the stand-by cooling setpoint value.
Stand-by Cooling Set point:
Default: 78 °F ( 25.5 °C )
The set value of this parameter should reside between the occupied and
unoccupied cooling setpoints and make sure that the difference between the
stand-by and occupied value can be recovered in a timely fashion when
movement is detected in the zone.
Stand-by Time:
Adjustable from 54 to 100 °F ( 12.2 to 37.8 °C ) in 0.5 degree increments.
This parameter sets the time delay between the moment where the PIR cover
detected the last movement in the area and the time which the thermostat
stand-by mode and setpoints become active.
Default 0.5 hours
Adjustable from 0.5 to 24 hours in .5hr increments
Unoccupied Time:
Default 0.0 hours
If no movement are detected in the area and the current mode is stand-by.
This parameter will then set the time delay between the moment where the
thermostat toggles to stand-by mode and the time which the thermostat
unoccupied mode and setpoints become active.
The factory value or 0.0 hours: Setting this parameter to its default value of
0.0 hours disables the unoccupied timer. This prevents the thermostat to drift
from stand-by mode to unoccupied mode when PIR functions are used
Adjustable from 0.0 to 24 hours in .5hr increments
2
3
Important Notes and Things to Know
When reviewing the following document and planning an application using a Viconics thermostat with PIR functionality, please
remember the important following notes:
•
Configuration of PIR Functions: All PIR application related configuration parameters are displayed in the
configuration menu or available as objects in the network object list. However, the advanced occupancy functionality
of a PIR attached to a thermostat is only enabled if either:
- A Viconics VI-PIR cover is installed on the thermostat
- A remote input is configured as a remote PIR sensor ( Motion NO or Motion NC )
•
PIR Cover Warm-Up Period: When VI-PIR accessory cover is used and a thermostat is powered up; there will be a
1 minute warm up period before any local movements can being detected and acknowledged by the PIR sensing
device. The local status LEDs for the VI-PIR cover will also not be active during that one minute period.
Only when that 1 minute period has elapsed after initial power up of the thermostat will the PIR functionality and local
movement status LEDs be activated.
•
Setpoints: The implemented stand-by setpoints are under the same limitations and restrictions as the occupied and
unoccupied ones. This means that:
- They use exactly the same range:
• Heating setpoints range are: 40 to 90 °F ( 4.5 to 32.0 °C )
• Cooling setpoints range are: 54 to 100 °F ( 12.0 to 37.5 °C )
- They are always limited by the applied minimum deadband configuration
- They will be limited by the Heat Maximum and Cool Minimum configuration parameters
All individual cooling setpoints and all individual heating setpoints can be set independently. However, A typical
arrangement will always have the set value of the stand-by parameters residing between the corresponding occupied
and unoccupied setpoint values.
The installer must make sure that the difference between the stand-by and occupied value can be recovered in a
timely fashion when movement is detected in the zone and large enough to warrant maximum energy savings.
Ex.:
Deadband
Unocc Heat
= 65F
St-By Heat
= 69F
Occ Heat
= 72F
Occ Cool
= 75F
St-By Cool
= 78F
Unocc Cool
= 82F
Room Temperature
•
Application Range: The range of applications covered with the PIR occupancy logic van be segmented in 2
important categories in terms of functionality. Both use different settings and have different behaviours:
- Hotel and lodging applications
- Standard commercial applications
Hotel and Lodging Applications can benefit the addition of an entry door switch wired to one of the appropriately
configured remote input of a thermostat.
When a door contact is used and configured, the Stand-By timer and its configuration are no longer active or used.
The occupancy front toggle between occupied and stand-by is now simply dictated by both the door contact and the
PIR sensing device used.
If movements are detected by the PIR cover, the room will always be occupied. The switch back to stand-by mode will
only happen if the door switch toggles open / close. Please review attached lodging application examples in the
document for more information
Standard Commercial Applications would not typically use a remote door switch contact attached to the
thermostat.
PIR occupancy functionality is simply dictated by both the Stand-By Timer and Unoccupied Timer configuration value
and movements being present or not in the area. Please review attached typical commercial application examples in
the document for more information
•
Unoccupied Timer Disable: In certain application cases, it may be desired to never let the local area enter the
unoccupied mode and always stay at the stand-by occupancy level when no activity is present.
4
This allows for advanced flexibility when used in conjunction with a network or in cases when areas always need to
be on stand-by status ready to respond to demand at any point in time.
Unoccupied timer set 6 Hours and stand-by timer set to 2 hours
Occupied
Stand-By Time
= 2 Hours
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 6 Hours
Unoccupied Time
= 6 Hours
Unoccupîed
Time
Time
Last Movement Detected
by PIR Activity
Stand-By Time Elapsed
= Stand-By Mode
Unoccupied Time Elapsed
= Unoccupied Mode
Stand-By Time Elapsed
= Stand-By Mode
Last Movement Detected
by PIR Activity
When the local PIR occupancy routine is running at the thermostat, the zone will drift into unoccupied mode when the
unoccupied timer is set above its factory default value of 0.0 hours
Unoccupied timer set 0 Hours and stand-by timer set to 2 hours
Occupied
Stand-By Time
= 2 Hours
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 0 Hours
Unoccupied Time
= 0 Hours
Unoccupîed
Time
Time
Last Movement Detected
by PIR Activity
Stand-By Time Elapsed
= Stand-By Mode
Last Movement Detected
by PIR Activity
Stand-By Time Elapsed
= Stand-By Mode
When the local PIR occupancy routine is running at the thermostat, the zone will never drift into unoccupied mode
when the unoccupied timer is set to its factory default value of 0.0 hours
•
Network Priority and Local Occupancy Routine:
The internal PIR occupancy logic implementation in conjunction with network commands has been conceived to give
the most flexibility while allowing for simple implementation and use.
Network Occupancy Commands: All VT700 series thermostat have 3 occupancy command levels. This is valid for
all network variations available for the thermostats: LON, BACnet-MS-TP or Wireless.
The 3 levels occupancy state level commands are:
State Occupancy
Function
Command Levels
Local occupancy
- Releases the thermostat to its own occupancy schemes
- This may be a PIR sensing device, a local schedule or an occupancy routine done by
one of the digital input
- This state command level is used to effectively release the thermostat to use the PIR
functions
Occupied
- Leaves the thermostat in occupied mode and cancels any local occupancy functions,
including the PIR occupancy routine
- This state command level is used to force the zone to be always occupied
Unoccupied
- Leaves the thermostat in unoccupied mode and cancels any local occupancy
functions, including the PIR occupancy routine
- This state command level is used to force the zone to be always unoccupied.
- The only local possible command is a local override if the thermostat is equipped with
such an option or if the local keypad lockout allows so
Stand-by is never a commandable level. It only exists as a feedback status level.
5
Network Occupancy Feedback Status: All VT700 series thermostats have 4 occupancy feedback levels. This is
valid for all network variations available for the thermostats: LON, BACnet-MS-TP or Wireless.
State Occupancy
Command Levels
Override / By-Pass
Occupied
Stand-By
Unoccupied
Function
Indicates that the zone is currently local occupied override mode from the unoccupied
state
This function will operate like a normal local override and its time value is as dictated
by the ToccTime configuration parameter setting
Indicates that the zone is currently occupied
This effective feedback state may be driven by a local occupancy routine like a PIR
sensor or by an occupied network command
Indicates that the zone is currently in stand-by mode
This effective feedback state can only be driven by a local PIR occupancy routine
Indicates that the zone is currently unoccupied
This effective feedback state may be driven by a local occupancy routine like a PIR
sensor or by an unoccupied network command
1) BACnet Object Used for Occupancy Commands and Feedback
Object Name
Object ID
Occupancy
Command
MV xx
Effective
Occupancy
MV xx
BACnet Index
Text
1
2
3
1
2
3
4
Occupied
Unoccupied
Local Occupancy ( PIR or Internal Schedule )
Occupied
Unoccupied
Temporary Occupied
Stand-By
2) LON Snivets Used for Occupancy Commands and Feedback
Snivet Name
network input
SNVT_occupancy
nviOccCmd
network output
SNVT_occupancy
nvoEffectOccup
Notes and Indexes
Default Null Value: OC_NUL = 0xFF Releases the thermostat to its internal
Occupancy function: Internal scheduling, PIR, etc….
Valid Range:
0 = OC_OCCUPIED
1 = OC_UNOCCUPIED
2 = OC_BYPASS – Not Used
3 = OC_STANDY – Not Used
0xFF = OC_NUL (Release to PIR or internal schedule)
This output network variable is used to indicate the actual occupancy mode of the
unit. This information is typically reported to a supervisory controller or provided
to another Space Comfort Controller to coordinate the operation of multiple units
Valid Range:
0 = OC_OCCUPIED
1 = OC_UNOCCUPIED
2 = OC_BYPASS1
3 = OC_STANDBY
Note 1: OC_BYPASS can be initiated by local override. NvoEffectOccup will only be
in OC_BYPASS for the duration of the ToccTime (nciGenOpts), until reinitiated by
either a transition of the local input or an update to nviOccManCmd.
•
Initial State, PIR Occupancy Routine: The initial effective occupancy state on power-up with either a PIR cover is 6
present or one of the inputs is configured for a remote PIR sensor is always Stand-By mode.
When the network effectively releases a thermostat to its local PIR routine from a previous occupied or unoccupied
network state, the resulting occupancy state is always Stand-By mode.
Initial Power-Up, Stand-Alone or Networked
Occupied
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 6 Hours
Unoccupîed
Time
Initial State at
Power-Up = Stand-By
First Movement Detected
by the PIR Cover
Unoccupied Time Elapsed
= Unoccupied Mode
Stand-By Time Elapsed
= Stand-By Mode
After Receiving the Local Occupancy / PIR Network Command From a Previous Unoccupied State
Occupied
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 6 Hours
Unoccupîed
Time
Current Network
Command = Unoccupied
Initial State at
Local Occupancy
Network Command
= Stand-By
Stand-By Time Elapsed
= Stand-By Mode
Unoccupied Time Elapsed
= Unoccupied Mode
First Movement Detected
by the PIR Cover
After Receiving the Local Occupancy / PIR Network Command From a Previous Occupied State
Occupied
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 6 Hours
Unoccupîed
Current Network
Command = Occupied
Initial State at
Local Occupancy
Network Command
= Stand-By
Time
Stand-By Time Elapsed
= Stand-By Mode
First Movement Detected
by the PIR Cover
Unoccupied Time Elapsed
= Unoccupied Mode
7
Typical Commercial Applications+
Commercial Applications
Application
Number
1
2
3
4
5
6
7
8
9
10
11
12
PIR Levels of
Occupancy
3
2
3
2
3
2
3
2
3
2
3
2
PIR Cover
Used
Yes
Yes
No
No
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Remote PIR
used
No
No
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
Yes
PIR Cover
Used
Yes
Yes
No
No
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Remote PIR
used
No
No
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
Yes
Network interface
None, stand-alone
None, stand-alone
None, stand-alone
None, stand-alone
None, stand-alone
None, stand-alone
Yes, LON or BACnet
Yes, LON or BACnet
Yes, LON or BACnet
Yes, LON or BACnet
Yes, LON or BACnet
Yes, LON or BACnet
Lodging Applications
Application
Number
13
14
15
16
17
18
19
20
21
22
23
24
PIR Levels of
Occupancy
3
2
3
2
3
2
3
2
3
2
3
2
Network interface
None, stand-alone
None, stand-alone
None, stand-alone
None, stand-alone
None, stand-alone
None, stand-alone
Yes, LON or BACnet
Yes, LON or BACnet
Yes, LON or BACnet
Yes, LON or BACnet
Yes, LON or BACnet
Yes, LON or BACnet
Advanced network interface can be obtained when thermostats are fully integrated to the reservation system
In these cases, the occupancy network commands state enumerations text presented by a front end system can be expanded
to better represent the nature of the application.
Occupancy network commands state
Local Occupancy ( PIR active )
Occupied
Unoccupied
Front end system state text examples
Room rented PIR economy enabled
Room rented high comfort assured
Room not rented
•
1) VT7300 Stand-alone fan coil application using 3 levels of occupancy with a VI-PIR accessory cover
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
VT73x0X5000 ( commercial models )
COV-PIR-FCU-C-5000 accessory cover
None, no function
2.0 hours
6.0 hours
None, stand-alone
Sequence of operation:
Occupied
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 6 Hours
Unoccupîed
Time
Initial State at
Power-Up = Stand-By
First Movement Detected
by the PIR Cover
Stand-By Time Elapsed
= Stand-By Mode
Unoccupied Time Elapsed
= Unoccupied Mode
At initial power-up, when the thermostat 24 Vac power supply is applied; the initial occupancy of the zone will be stand-by
mode if the PIR device do not detect any movements.
As soon as the PIR device detects a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used.
Anytime the PIR device detects local motion, the elapsed stand-by timer value will be reset. If no motion is detected in the
zone for the entire stand-by timer duration, then the room switches to stand-by mode and the stand-by setpoints are used.
While in stand-by mode, if no motion is detected in the zone for the entire unoccupied timer duration, then the room switches
to unoccupied mode and the unoccupied setpoints are used.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
•
2) VT7300 Stand-alone fan coil application using 2 levels of occupancy with a VI-PIR accessory cover
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
VT73x0X5000 ( commercial models )
COV-PIR-FCU-C-5000 accessory cover
None, no function
2.0 hours
0.0 hours
None, stand-alone
Sequence of operation:
Occupied
Stand-By Time
= 2 Hours
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 0 Hours
Unoccupied Time
= 0 Hours
Unoccupîed
Time
Time
Initial State at
Power-Up = Stand-By
First Movement Detected
by the PIR Cover
Stand-By Time Elapsed
= Stand-By Mode
Last Movement Detected
by PIR Activity
Stand-By Time Elapsed
= Stand-By Mode
At initial power-up, when the thermostat 24 Vac power supply is applied; the initial occupancy of the zone will be stand-by
mode if the PIR device do not detect any movements.
As soon as the PIR device detects a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used.
Anytime the PIR device detects local motion, the elapsed stand-by timer value will be reset. If no motion is detected in the
zone for the entire stand-by timer duration, then the room switches to stand-by mode and the stand-by setpoints are used.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
The local zone never goes into unoccupied mode and the unoccupied setpoints are never used.
8
•
9
3) VT7300 Stand-alone fan coil application using 3 levels of occupancy with a remote PIR sensor
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
Remote PIR Sensor
VT73x0X5000 ( commercial models )
BI1 configured for remote PIR sensor
None, no function
2.0 hours
6.0 hours
None, stand-alone
Sequence of operation:
Occupied
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 6 Hours
Unoccupîed
Time
Initial State at
Power-Up = Stand-By
First Movement Detected
by a PIR Device
Unoccupied Time Elapsed
= Unoccupied Mode
Stand-By Time Elapsed
= Stand-By Mode
At initial power-up, when the thermostat 24 Vac power supply is applied; the initial occupancy of the zone will be stand-by
mode if the PIR device do not detect any movements.
As soon as the PIR device detects a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used.
Anytime the PIR device detects local motion, the elapsed stand-by timer value will be reset. If no motion is detected in the
zone for the entire stand-by timer duration, then the room switches to stand-by mode and the stand-by setpoints are used.
While in stand-by mode, if no motion is detected in the zone for the entire unoccupied timer duration, then the room switches
to unoccupied mode and the unoccupied setpoints are used.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
•
4) VT7300 Stand-alone fan coil application using 2 levels of occupancy with a remote PIR sensor
Remote PIR Sensor
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
VT73x0X5000 ( commercial models )
BI1 configured for remote PIR sensor
None, no function
2.0 hours
0.0 hours
None, stand-alone
Sequence of operation:
Occupied
Stand-By Time
= 2 Hours
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 0 Hours
Unoccupied Time
= 0 Hours
Unoccupîed
Time
Time
Initial State at
Power-Up = Stand-By
First Movement Detected
by a PIR Device
Stand-By Time Elapsed
= Stand-By Mode
Last Movement Detected
by PIR Activity
Stand-By Time Elapsed
= Stand-By Mode
At initial power-up, when the thermostat 24 Vac power supply is applied; the initial occupancy of the zone will be stand-by
mode if the PIR device do not detect any movements.
As soon as the PIR device detects a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used.
Anytime the PIR device detects local motion, the elapsed stand-by timer value will be reset. If no motion is detected in the
zone for the entire stand-by timer duration, then the room switches to stand-by mode and the stand-by setpoints are used.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
The local zone never goes into unoccupied mode and the unoccupied setpoints are never used.
•
5) VT7300 Stand-alone fan coil application using 3 levels of occupancy with dual PIR sensors
Set-up and Configuration
Thermostat used
PIR used
10
Remote PIR Sensor
VT73x0X5000 ( commercial models )
BI1 configured for remote PIR sensor and
COV-PIR-FCU-C-5000 accessory cover
None, no function
2.0 hours
6.0 hours
None, stand-alone
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
Sequence of operation:
Occupied
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 6 Hours
Unoccupîed
Time
Initial State at
Power-Up = Stand-By
First Movement Detected
by a PIR Device
Unoccupied Time Elapsed
= Unoccupied Mode
Stand-By Time Elapsed
= Stand-By Mode
At initial power-up, when the thermostat 24 Vac power supply is applied; the initial occupancy of the zone will be stand-by
mode if the PIR devices do not detect any movements.
As soon as any of the PIR device detect a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used.
Anytime local motion is detected by one of the PIR devices, the elapsed stand-by timer value will be reset. If either PIR
devices in the zone detect no motion for the entire stand-by timer duration, then the room switches to stand-by mode and the
stand-by setpoints are used.
While in stand-by mode, if no motion is detected in the zone by either PIR devices for the entire unoccupied timer duration,
then the room switches to unoccupied mode and the unoccupied setpoints are used.
At anytime, if one of the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
•
6) VT7300 Stand-alone fan coil application using 2 levels of occupancy with dual PIR sensors
Set-up and Configuration
Thermostat used
PIR used
Remote PIR Sensor
VT73x0X5000 ( commercial models )
BI1 configured for remote PIR sensor and
COV-PIR-FCU-C-5000 accessory cover
None, no function
2.0 hours
0.0 hours
None, stand-alone
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
Sequence of operation:
Occupied
Stand-By Time
= 2 Hours
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 0 Hours
Unoccupied Time
= 0 Hours
Unoccupîed
Time
Time
Initial State at
Power-Up = Stand-By
First Movement Detected
by a PIR Device
Stand-By Time Elapsed
= Stand-By Mode
Last Movement Detected
by PIR Activity
Stand-By Time Elapsed
= Stand-By Mode
At initial power-up, when the thermostat 24 Vac power supply is applied; the initial occupancy of the zone will be stand-by
mode if the PIR devices do not detect any movements.
As soon as any of the PIR devices detect a movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
Anytime local motion is detected by one of the PIR devices, the elapsed stand-by timer value will be reset. If either PIR
devices in the zone detect no motion for the entire stand-by timer duration, then the room switches to stand-by mode and the
stand-by setpoints are used.
At anytime, if one of the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
The local zone never goes into unoccupied mode and the unoccupied setpoints are never used.
•
7) VT7300 Networked fan coil application using 3 levels of occupancy with a VI-PIR accessory cover
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
11
BACnet or Echelon Network
VT73x0X5000(BorE) ( commercial models )
COV-PIR-FCU-C-5000 accessory cover
None, no function
2.0 hours
6.0 hours
Echelon or BACnet MS-TP
Sequence of operation:
Occupied
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 6 Hours
Unoccupîed
Time
Initial Network
Command = Unoccupied
PIR Movements Ignored
Network Command
= Local PIR Occupancy
Stand-By Time Elapsed
= Stand-By Mode
First Movement Detected
by a PIR Device
Unoccupied Time Elapsed
= Unoccupied Mode
Network Command
= Occupied
PIR Movements Ignored
Network Command
= Unoccupied
PIR Movements Ignored
At initial power-up, when the thermostat 24 Vac power supply is applied; if there is no occupancy network command received
by the thermostat and if the PIR device do not detect any movements, the initial occupancy of the zone will be stand-by mode.
Occupied state network command
At any time, an occupied network command will always force the local zone to be in occupied mode and to use the occupied
setpoints.
Unoccupied state network command
At any time, an unoccupied network command will always force the local zone to be in unoccupied mode and to use the
unoccupied setpoints. If the thermostat local override function is not locked out by configuration, the local user may initiate a
temporary local override to occupied as dictated by the temporary occupancy time configuration parameter setting.
Local occupancy state network command
When the thermostat receives a local occupancy state network command, the local PIR occupancy loop will now be enabled.
If the PIR devices do not then detect any movements, the occupancy of the zone will be stand-by mode.
As soon as the PIR device detects a movement or motion while in the local occupancy state network command, the
occupancy status switches to occupied and the occupied setpoints are used.
Anytime the PIR device detects local motion, the elapsed stand-by timer value will be reset. If no motion is detected in the
zone for the entire stand-by timer duration, then the room switches to stand-by mode and the stand-by setpoints are used.
While in stand-by mode, if no motion is detected in the zone for the entire unoccupied timer duration, then the room switches
to unoccupied mode and the unoccupied setpoints are used.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
•
8) VT7300 Networked fain coil application using 2 levels of occupancy with a VI-PIR accessory cover
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
VT73x0X5000(BorE) ( commercial models )
COV-PIR-FCU-C-5000 accessory cover
None, no function
2.0 hours
0.0 hours
Echelon or BACnet MS-TP
12
BACnet or Echelon Network
Sequence of operation:
Occupied
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 0 Hours
Unoccupîed
Time
Initial Network
Command = Unoccupied
PIR Movements Ignored
Network Command
= Local PIR Occupancy
Stand-By Time Elapsed
= Stand-By Mode
First Movement Detected
by a PIR Device
Network Command
= Occupied
PIR Movements Ignored
Network Command
= Unoccupied
PIR Movements Ignored
At initial power-up, when the thermostat 24 Vac power supply is applied; if there is no occupancy network command received
by the thermostat and if the PIR device do not detect any movements, the initial occupancy of the zone will be stand-by mode.
Occupied state network command
At any time, an occupied network command will always force the local zone to be in occupied mode and to use the occupied
setpoints.
Unoccupied state network command
At any time, an unoccupied network command will always force the local zone to be in unoccupied mode and to use the
unoccupied setpoints. If the thermostat local override function is not locked out by configuration, the local user may initiate a
temporary local override to occupied as dictated by the temporary occupancy time configuration parameter setting.
Local occupancy state network command
When the thermostat receives a local occupancy state network command, the local PIR occupancy loop will now be enabled.
If the PIR devices do not then detect any movements, the occupancy of the zone will be stand-by mode.
As soon as the PIR device detects a movement or motion while in the local occupancy state network command, the
occupancy status switches to occupied and the occupied setpoints are used.
Anytime the PIR device detects local motion, the elapsed stand-by timer value will be reset. If no motion is detected in the
zone for the entire stand-by timer duration, then the room switches to stand-by mode and the stand-by setpoints are used.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
While in the local occupancy state network command, the local zone never goes into unoccupied mode and the unoccupied
setpoints are never used
•
13
9) VT7300 Networked fan coil application using 3 levels of occupancy with a remote PIR sensor
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
BACnet or Echelon Network
Remote PIR Sensor
VT73x0X5000(BorE) ( commercial models )
BI1 configured for remote PIR sensor
None, no function
2.0 hours
6.0 hours
Echelon or BACnet MS-TP
Sequence of operation:
Occupied
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 6 Hours
Unoccupîed
Time
Initial Network
Command = Unoccupied
PIR Movements Ignored
Network Command
= Local PIR Occupancy
Stand-By Time Elapsed
= Stand-By Mode
First Movement Detected
by a PIR Device
Unoccupied Time Elapsed
= Unoccupied Mode
Network Command
= Occupied
PIR Movements Ignored
Network Command
= Unoccupied
PIR Movements Ignored
At initial power-up, when the thermostat 24 Vac power supply is applied; if there is no occupancy network command received
by the thermostat and if the PIR device do not detect any movements, the initial occupancy of the zone will be stand-by mode.
Occupied state network command
At any time, an occupied network command will always force the local zone to be in occupied mode and to use the occupied
setpoints.
Unoccupied state network command
At any time, an unoccupied network command will always force the local zone to be in unoccupied mode and to use the
unoccupied setpoints. If the thermostat local override function is not locked out by configuration, the local user may initiate a
temporary local override to occupied as dictated by the temporary occupancy time configuration parameter setting.
Local occupancy state network command
When the thermostat receives a local occupancy state network command, the local PIR occupancy loop will now be enabled.
If the PIR devices do not then detect any movements, the occupancy of the zone will be stand-by mode.
As soon as the PIR device detects a movement or motion while in the local occupancy state network command, the
occupancy status switches to occupied and the occupied setpoints are used.
Anytime the PIR device detects local motion, the elapsed stand-by timer value will be reset. If no motion is detected in the
zone for the entire stand-by timer duration, then the room switches to stand-by mode and the stand-by setpoints are used.
While in stand-by mode, if no motion is detected in the zone for the entire unoccupied timer duration, then the room switches
to unoccupied mode and the unoccupied setpoints are used.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
•
10) VT7300 Networked fan coil application using 2 levels of occupancy with a remote PIR sensor
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
VT73x0X5000(BorE) ( commercial models )
BI1 configured for remote PIR sensor
None, no function
2.0 hours
0.0 hours
Echelon or BACnet MS-TP
BACnet or Echelon Network
14
Remote PIR Sensor
Sequence of operation:
Occupied
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 0 Hours
Unoccupîed
Time
Initial Network
Command = Unoccupied
PIR Movements Ignored
Network Command
= Local PIR Occupancy
Stand-By Time Elapsed
= Stand-By Mode
First Movement Detected
by a PIR Device
Network Command
= Occupied
PIR Movements Ignored
Network Command
= Unoccupied
PIR Movements Ignored
At initial power-up, when the thermostat 24 Vac power supply is applied; if there is no occupancy network command received
by the thermostat and if the PIR device do not detect any movements, the initial occupancy of the zone will be stand-by mode.
Occupied state network command
At any time, an occupied network command will always force the local zone to be in occupied mode and to use the occupied
setpoints.
Unoccupied state network command
At any time, an unoccupied network command will always force the local zone to be in unoccupied mode and to use the
unoccupied setpoints. If the thermostat local override function is not locked out by configuration, the local user may initiate a
temporary local override to occupied as dictated by the temporary occupancy time configuration parameter setting.
Local occupancy state network command
When the thermostat receives a local occupancy state network command, the local PIR occupancy loop will now be enabled.
If the PIR devices do not then detect any movements, the occupancy of the zone will be stand-by mode.
As soon as the PIR device detects a movement or motion while in the local occupancy state network command, the
occupancy status switches to occupied and the occupied setpoints are used.
Anytime the PIR device detects local motion, the elapsed stand-by timer value will be reset. If no motion is detected in the
zone for the entire stand-by timer duration, then the room switches to stand-by mode and the stand-by setpoints are used.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
While in the local occupancy state network command, the local zone never goes into unoccupied mode and the unoccupied
setpoints are never used
•
15
11) VT7300 Networked fan coil application using 3 levels of occupancy with dual PIR sensors
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
BACnet or Echelon Network
VT73x0X5000(BorE) ( commercial models )
BI1 configured for remote PIR sensor and
COV-PIR-FCU-C-5000 accessory cover
None, no function
2.0 hours
6.0 hours
Echelon or BACnet MS-TP
Remote PIR Sensor
Sequence of operation:
Occupied
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 6 Hours
Unoccupîed
Time
Initial Network
Command = Unoccupied
PIR Movements Ignored
Network Command
= Local PIR Occupancy
Stand-By Time Elapsed
= Stand-By Mode
First Movement Detected
by a PIR Device
Unoccupied Time Elapsed
= Unoccupied Mode
Network Command
= Occupied
PIR Movements Ignored
Network Command
= Unoccupied
PIR Movements Ignored
At initial power-up, when the thermostat 24 Vac power supply is applied; if there is no occupancy network command received
by the thermostat and if the PIR device do not detect any movements, the initial occupancy of the zone will be stand-by mode.
Occupied state network command
At any time, an occupied network command will always force the local zone to be in occupied mode and to use the occupied
setpoints.
Unoccupied state network command
At any time, an unoccupied network command will always force the local zone to be in unoccupied mode and to use the
unoccupied setpoints. If the thermostat local override function is not locked out by configuration, the local user may initiate a
temporary local override to occupied as dictated by the temporary occupancy time configuration parameter setting.
Local occupancy state network command
When the thermostat receives a local occupancy state network command, the local PIR occupancy loop will now be enabled.
If the PIR devices do not then detect any movements, the occupancy of the zone will be stand-by mode.
As soon as the PIR device detects a movement or motion while in the local occupancy state network command, the
occupancy status switches to occupied and the occupied setpoints are used.
Anytime the PIR device detects local motion, the elapsed stand-by timer value will be reset. If no motion is detected in the
zone for the entire stand-by timer duration, then the room switches to stand-by mode and the stand-by setpoints are used.
While in stand-by mode, if no motion is detected in the zone for the entire unoccupied timer duration, then the room switches
to unoccupied mode and the unoccupied setpoints are used.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
•
16
12) VT7300 Networked fan coil application using 2 levels of occupancy with dual PIR sensors
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
VT73x0X5000(BorE) ( commercial models )
BI1 configured for remote PIR sensor and
COV-PIR-FCU-C-5000 accessory cover
None, no function
2.0 hours
0.0 hours
Echelon or BACnet MS-TP
BACnet or Echelon Network
Remote PIR Sensor
Sequence of operation:
Occupied
Stand-By Time
= 2 Hours
Stand-By
Unoccupied Time
= 0 Hours
Unoccupîed
Time
Initial Network
Command = Unoccupied
PIR Movements Ignored
Network Command
= Local PIR Occupancy
Stand-By Time Elapsed
= Stand-By Mode
First Movement Detected
by a PIR Device
Network Command
= Occupied
PIR Movements Ignored
Network Command
= Unoccupied
PIR Movements Ignored
At initial power-up, when the thermostat 24 Vac power supply is applied; if there is no occupancy network command received
by the thermostat and if the PIR device do not detect any movements, the initial occupancy of the zone will be stand-by mode.
Occupied state network command
At any time, an occupied network command will always force the local zone to be in occupied mode and to use the occupied
setpoints.
Unoccupied state network command
At any time, an unoccupied network command will always force the local zone to be in unoccupied mode and to use the
unoccupied setpoints. If the thermostat local override function is not locked out by configuration, the local user may initiate a
temporary local override to occupied as dictated by the temporary occupancy time configuration parameter setting.
Local occupancy state network command
When the thermostat receives a local occupancy state network command, the local PIR occupancy loop will now be enabled.
If the PIR devices do not then detect any movements, the occupancy of the zone will be stand-by mode.
As soon as the PIR device detects a movement or motion while in the local occupancy state network command, the
occupancy status switches to occupied and the occupied setpoints are used.
Anytime the PIR device detects local motion, the elapsed stand-by timer value will be reset. If no motion is detected in the
zone for the entire stand-by timer duration, then the room switches to stand-by mode and the stand-by setpoints are used.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
While in the local occupancy state network command, the local zone never goes into unoccupied mode and the unoccupied
setpoints are never used
•
13) VT7300 Stand-alone fan coil application using 3 levels of occupancy with a VI-PIR accessory cover
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
17
Door Switch
VT73x5X5000 ( lodging models )
COV-PIR-FCU-C-5000 accessory cover
Door dry contact
Not used
6.0 hours
None, stand-alone
Sequence of operation:
Occupied
Always
Occupied
Stand-By
Unoccupied Time
= 6 Hours
Unoccupîed
Time
Initial State at
Power-Up = Stand-By
Unoccupied Time Elapsed
= Unoccupied Mode
Door Open/Close
Toggle Detected
At initial power-up, when the thermostat 24 Vac power supply is applied; the initial occupancy of the zone will be stand-by
mode if the PIR device do not detect any movements.
As soon as the PIR device detects a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used. The room will then be in occupied mode until a door toggle is detected.
If a door toggle is detected, then the room switches to stand-by mode and the stand-by setpoints are used. If any occupants
are left in the room, local movements must be seen to resume the occupied mode.
While in stand-by mode, if no motion is detected in the zone for the entire unoccupied timer duration, then the room switches
to unoccupied mode and the unoccupied setpoints are used.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
•
14) VT7300 Stand-alone fan coil application using 2 levels of occupancy with a VI-PIR accessory cover
Door Switch
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
VT73x5X5000 ( lodging models )
COV-PIR-FCU-C-5000 accessory cover
Door dry contact
Not used
0.0 hours
None, stand-alone
Sequence of operation:
Occupied
Always
Occupied
Always
Occupied
Stand-By
Unoccupied Time
= 0 Hours
Unoccupied Time
= 0 Hours
Unoccupîed
Time
Time
Initial State at
Power-Up = Stand-By
First Movement Detected
by a PIR Device
Door Open/Close
Toggle Detected
Last Movement Detected
by PIR Activity
Door Open/Close
Toggle Detected
At initial power-up, when the thermostat 24 Vac power supply is applied; the initial occupancy of the zone will be stand-by
mode if the PIR device do not detect any movements.
As soon as the PIR device detects a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used. The room will then be in occupied mode until a door toggle is detected.
If a door toggle is detected, then the room switches to stand-by mode and the stand-by setpoints are used. If any occupants
are left in the room, local movements must be seen to resume the occupied mode.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
The local zone never goes into unoccupied mode and the unoccupied setpoints are never used.
•
18
15) VT7300 Stand-alone fan coil application using 3 levels of occupancy with a remote PIR sensor
Remote PIR Sensor
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
Door Switch
VT73x5X5000 ( lodging models )
BI1 configured for remote PIR sensor
Door dry contact
Not used
6.0 hours
None, stand-alone
Sequence of operation:
Occupied
Always
Occupied
Stand-By
Unoccupied Time
= 6 Hours
Unoccupîed
Time
Initial State at
Power-Up = Stand-By
Unoccupied Time Elapsed
= Unoccupied Mode
Door Open/Close
Toggle Detected
At initial power-up, when the thermostat 24 Vac power supply is applied; the initial occupancy of the zone will be stand-by
mode if the PIR device do not detect any movements.
As soon as the PIR device detects a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used. The room will then be in occupied mode until a door toggle is detected.
If a door toggle is detected, then the room switches to stand-by mode and the stand-by setpoints are used. If any occupants
are left in the room, local movements must be seen to resume the occupied mode.
While in stand-by mode, if no motion is detected in the zone for the entire unoccupied timer duration, then the room switches
to unoccupied mode and the unoccupied setpoints are used.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
•
16) VT7300 Stand-alone fan coil application using 2 levels of occupancy with a remote PIR sensor
Remote PIR Sensor
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
Door Switch
VT73x5X5000 ( lodging models )
BI1 configured for remote PIR sensor
Door dry contact
Not used
0.0 hours
None, stand-alone
Sequence of operation:
Occupied
Always
Occupied
Always
Occupied
Stand-By
Unoccupied Time
= 0 Hours
Unoccupied Time
= 0 Hours
Unoccupîed
Time
Time
Initial State at
Power-Up = Stand-By
First Movement Detected
by a PIR Device
Door Open/Close
Toggle Detected
Last Movement Detected
by PIR Activity
Door Open/Close
Toggle Detected
t initial power-up, when the thermostat 24 Vac power supply is applied; the initial occupancy of the zone will be stand-by mode
if the PIR device do not detect any movements.
As soon as the PIR device detects a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used. The room will then be in occupied mode until a door toggle is detected.
If a door toggle is detected, then the room switches to stand-by mode and the stand-by setpoints are used. If any occupants
are left in the room, local movements must be seen to resume the occupied mode.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
The local zone never goes into unoccupied mode and the unoccupied setpoints are never used.
•
19
17) VT7300 Stand-alone fan coil application using 3 levels of occupancy with dual PIR sensors
Set-up and Configuration
Thermostat used
PIR used
Remote PIR Sensor
VT73x5X5000 ( lodging models )
BI1 configured for remote PIR sensor and
COV-PIR-FCU-C-5000 accessory cover
Door dry contact
2.0 hours
6.0 hours
None, stand-alone
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
Door Switch
Sequence of operation:
Occupied
Always
Occupied
Stand-By
Unoccupied Time
= 6 Hours
Unoccupîed
Time
Initial State at
Power-Up = Stand-By
Unoccupied Time Elapsed
= Unoccupied Mode
Door Open/Close
Toggle Detected
At initial power-up, when the thermostat 24 Vac power supply is applied; the initial occupancy of the zone will be stand-by
mode if the PIR device do not detect any movements.
As soon as the PIR device detects a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used. The room will then be in occupied mode until a door toggle is detected.
If a door toggle is detected, then the room switches to stand-by mode and the stand-by setpoints are used. If any occupants
are left in the room, local movements must be seen to resume the occupied mode.
While in stand-by mode, if no motion is detected in the zone for the entire unoccupied timer duration, then the room switches
to unoccupied mode and the unoccupied setpoints are used.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
•
18) VT7300 Stand-alone fan coil application using 2 levels of occupancy with dual PIR sensors
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
Remote PIR Sensor
VT73x5X5000 ( lodging models )
BI1 configured for remote PIR sensor and
COV-PIR-FCU-C-5000 accessory cover
Door dry contact
Not used
0.0 hours
None, stand-alone
Door Switch
Sequence of operation:
Occupied
Always
Occupied
Always
Occupied
Stand-By
Unoccupied Time
= 0 Hours
Unoccupied Time
= 0 Hours
Unoccupîed
Time
Time
Initial State at
Power-Up = Stand-By
First Movement Detected
by a PIR Device
Door Open/Close
Toggle Detected
Last Movement Detected
by PIR Activity
Door Open/Close
Toggle Detected
At initial power-up, when the thermostat 24 Vac power supply is applied; the initial occupancy of the zone will be stand-by
mode if the PIR device do not detect any movements.
As soon as the PIR device detects a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used. The room will then be in occupied mode until a door toggle is detected.
If a door toggle is detected, then the room switches to stand-by mode and the stand-by setpoints are used. If any occupants
are left in the room, local movements must be seen to resume the occupied mode.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
The local zone never goes into unoccupied mode and the unoccupied setpoints are never used.
•
19) VT7300 Networked fan coil application using 3 levels of occupancy with a VI-PIR accessory cover
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
20
BACnet or Echelon Network
VT73x5X5000(BorE)…( lodging models )
COV-PIR-FCU-C-5000 accessory cover
Door dry contact
Not used
6.0 hours
Echelon or BACnet MS-TP
Door Switch
Advanced network interface can be obtained when thermostats are fully
integrated to the reservation system
In these cases, the occupancy network commands state enumerations text
presented by a front end system can be expanded to better represent the
nature of the application.
Occupancy network commands state
Local Occupancy ( PIR active )
Occupied
Unoccupied
Front end system state text examples
Room rented PIR economy enabled
Room rented high comfort assured
Room not rented
Sequence of operation:
Occupied
Always
Occupied
Stand-By
Unoccupied Time
= 6 Hours
Unoccupîed
Time
Initial Network
Command = Unoccupied
PIR Movements Ignored
Network Command
= Local PIR Occupancy
Door Open/Close
Toggle Detected
First Movement Detected
by a PIR Device
Unoccupied Time Elapsed
= Unoccupied Mode
Network Command
= Occupied
PIR Movements Ignored
Network Command
= Unoccupied
PIR Movements Ignored
At initial power-up, when the thermostat 24 Vac power supply is applied; if there is no occupancy network command received
by the thermostat and if the PIR device do not detect any movements, the initial occupancy of the zone will be stand-by mode.
Occupied state network command
At any time, an occupied network command will always force the local zone to be in occupied mode and to use the occupied
setpoints.
Unoccupied state network command
At any time, an unoccupied network command will always force the local zone to be in unoccupied mode and to use the
unoccupied setpoints. If the thermostat local override function is not locked out by configuration, the local user may initiate a
temporary local override to occupied as dictated by the temporary occupancy time configuration parameter setting.
Local occupancy state network command
When the thermostat receives a local occupancy state network command, the local PIR occupancy loop will now be enabled.
If the PIR devices do not then detect any movements, the occupancy of the zone will be stand-by mode.
As soon as the PIR device detects a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used. The room will then be in occupied mode until a door toggle is detected.
If a door toggle is detected, then the room switches to stand-by mode and the stand-by setpoints are used. If any occupants
are left in the room, local movements must be seen to resume the occupied mode.
While in stand-by mode, if no motion is detected in the zone for the entire unoccupied timer duration, then the room switches
to unoccupied mode and the unoccupied setpoints are used.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
•
20) VT7300 Networked fain coil application using 2 levels of occupancy with a VI-PIR accessory cover
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
21
BACnet or Echelon Network
VT73x5X5000(BorE)…( lodging models )
COV-PIR-FCU-C-5000 accessory cover
Door dry contact
Not used
0.0 hours
Echelon or BACnet MS-TP
Door Switch
Advanced network interface can be obtained when thermostats are fully
integrated to the reservation system
In these cases, the occupancy network commands state enumerations text
presented by a front end system can be expanded to better represent the
nature of the application.
Occupancy network commands state
Local Occupancy ( PIR active )
Occupied
Unoccupied
Front end system state text examples
Room rented PIR economy enabled
Room rented high comfort assured
Room not rented
Sequence of operation:
Occupied
Always
Occupied
Stand-By
Unoccupied Time
= 0 Hours
Unoccupîed
Time
Initial Network
Command = Unoccupied
PIR Movements Ignored
Network Command
= Local PIR Occupancy
Door Open/Close
Toggle Detected
First Movement Detected
by a PIR Device
Network Command
= Occupied
PIR Movements Ignored
Network Command
= Unoccupied
PIR Movements Ignored
At initial power-up, when the thermostat 24 Vac power supply is applied; if there is no occupancy network command received
by the thermostat and if the PIR device do not detect any movements, the initial occupancy of the zone will be stand-by mode.
Occupied state network command
At any time, an occupied network command will always force the local zone to be in occupied mode and to use the occupied
setpoints.
Unoccupied state network command
At any time, an unoccupied network command will always force the local zone to be in unoccupied mode and to use the
unoccupied setpoints. If the thermostat local override function is not locked out by configuration, the local user may initiate a
temporary local override to occupied as dictated by the temporary occupancy time configuration parameter setting.
Local occupancy state network command
When the thermostat receives a local occupancy state network command, the local PIR occupancy loop will now be enabled.
If the PIR devices do not then detect any movements, the occupancy of the zone will be stand-by mode.
As soon as the PIR device detects a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used. The room will then be in occupied mode until a door toggle is detected.
If a door toggle is detected, then the room switches to stand-by mode and the stand-by setpoints are used. If any occupants
are left in the room, local movements must be seen to resume the occupied mode.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
The local zone never goes into unoccupied mode and the unoccupied setpoints are never used.
•
22
21 VT7300 Networked fan coil application using 3 levels of occupancy with a remote PIR sensor
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
BACnet or Echelon Network
VT73x5X5000(BorE)…( lodging models )
BI1 configured for remote PIR sensor
Door dry contact
Not used
6.0 hours
Echelon or BACnet MS-TP
Remote PIR Sensor
Door Switch
Advanced network interface can be obtained when thermostats are fully
integrated to the reservation system
In these cases, the occupancy network commands state enumerations text
presented by a front end system can be expanded to better represent the
nature of the application.
Occupancy network commands state
Local Occupancy ( PIR active )
Occupied
Unoccupied
Front end system state text examples
Room rented PIR economy enabled
Room rented high comfort assured
Room not rented
Sequence of operation:
Occupied
Always
Occupied
Stand-By
Unoccupied Time
= 6 Hours
Unoccupîed
Time
Initial Network
Command = Unoccupied
PIR Movements Ignored
Network Command
= Local PIR Occupancy
Door Open/Close
Toggle Detected
First Movement Detected
by a PIR Device
Unoccupied Time Elapsed
= Unoccupied Mode
Network Command
= Occupied
PIR Movements Ignored
Network Command
= Unoccupied
PIR Movements Ignored
At initial power-up, when the thermostat 24 Vac power supply is applied; if there is no occupancy network command received
by the thermostat and if the PIR device do not detect any movements, the initial occupancy of the zone will be stand-by mode.
Occupied state network command
At any time, an occupied network command will always force the local zone to be in occupied mode and to use the occupied
setpoints.
Unoccupied state network command
At any time, an unoccupied network command will always force the local zone to be in unoccupied mode and to use the
unoccupied setpoints. If the thermostat local override function is not locked out by configuration, the local user may initiate a
temporary local override to occupied as dictated by the temporary occupancy time configuration parameter setting.
Local occupancy state network command
When the thermostat receives a local occupancy state network command, the local PIR occupancy loop will now be enabled.
If the PIR devices do not then detect any movements, the occupancy of the zone will be stand-by mode.
As soon as the PIR device detects a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used. The room will then be in occupied mode until a door toggle is detected.
If a door toggle is detected, then the room switches to stand-by mode and the stand-by setpoints are used. If any occupants
are left in the room, local movements must be seen to resume the occupied mode.
While in stand-by mode, if no motion is detected in the zone for the entire unoccupied timer duration, then the room switches
to unoccupied mode and the unoccupied setpoints are used.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
•
23
22) VT7300 Networked fan coil application using 2 levels of occupancy with a remote PIR sensor
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
BACnet or Echelon Network
VT73x5X5000(BorE)…( lodging models )
BI1 configured for remote PIR sensor
Door dry contact
Not used
0.0 hours
Echelon or BACnet MS-TP
Remote PIR Sensor
Door Switch
Advanced network interface can be obtained when thermostats are fully
integrated to the reservation system
In these cases, the occupancy network commands state enumerations text
presented by a front end system can be expanded to better represent the
nature of the application.
Occupancy network commands state
Local Occupancy ( PIR active )
Occupied
Unoccupied
Front end system state text examples
Room rented PIR economy enabled
Room rented high comfort assured
Room not rented
Sequence of operation:
Occupied
Always
Occupied
Stand-By
Unoccupied Time
= 0 Hours
Unoccupîed
Time
Initial Network
Command = Unoccupied
PIR Movements Ignored
Network Command
= Local PIR Occupancy
Door Open/Close
Toggle Detected
First Movement Detected
by a PIR Device
Network Command
= Occupied
PIR Movements Ignored
Network Command
= Unoccupied
PIR Movements Ignored
At initial power-up, when the thermostat 24 Vac power supply is applied; if there is no occupancy network command received
by the thermostat and if the PIR device do not detect any movements, the initial occupancy of the zone will be stand-by mode.
Occupied state network command
At any time, an occupied network command will always force the local zone to be in occupied mode and to use the occupied
setpoints.
Unoccupied state network command
At any time, an unoccupied network command will always force the local zone to be in unoccupied mode and to use the
unoccupied setpoints. If the thermostat local override function is not locked out by configuration, the local user may initiate a
temporary local override to occupied as dictated by the temporary occupancy time configuration parameter setting.
Local occupancy state network command
When the thermostat receives a local occupancy state network command, the local PIR occupancy loop will now be enabled.
If the PIR devices do not then detect any movements, the occupancy of the zone will be stand-by mode.
As soon as the PIR device detects a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used. The room will then be in occupied mode until a door toggle is detected.
If a door toggle is detected, then the room switches to stand-by mode and the stand-by setpoints are used. If any occupants
are left in the room, local movements must be seen to resume the occupied mode.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
The local zone never goes into unoccupied mode and the unoccupied setpoints are never used.
•
24
23) VT7300 Networked fan coil application using 3 levels of occupancy with dual PIR sensors
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
BACnet or Echelon Network
VT73x5X5000(BorE)…( lodging models )
BI1 configured for remote PIR sensor and
COV-PIR-FCU-C-5000 accessory cover
Door dry contact
Not used
6.0 hours
Echelon or BACnet MS-TP
Remote PIR Sensor
Door Switch
Advanced network interface can be obtained when thermostats are fully
integrated to the reservation system
In these cases, the occupancy network commands state enumerations text
presented by a front end system can be expanded to better represent the
nature of the application.
Occupancy network commands state
Local Occupancy ( PIR active )
Occupied
Unoccupied
Front end system state text examples
Room rented PIR economy enabled
Room rented high comfort assured
Room not rented
Sequence of operation:
Occupied
Always
Occupied
Stand-By
Unoccupied Time
= 6 Hours
Unoccupîed
Time
Initial Network
Command = Unoccupied
PIR Movements Ignored
Network Command
= Local PIR Occupancy
Door Open/Close
Toggle Detected
First Movement Detected
by a PIR Device
Unoccupied Time Elapsed
= Unoccupied Mode
Network Command
= Occupied
PIR Movements Ignored
Network Command
= Unoccupied
PIR Movements Ignored
At initial power-up, when the thermostat 24 Vac power supply is applied; if there is no occupancy network command received
by the thermostat and if the PIR device do not detect any movements, the initial occupancy of the zone will be stand-by mode.
Occupied state network command
At any time, an occupied network command will always force the local zone to be in occupied mode and to use the occupied
setpoints.
Unoccupied state network command
At any time, an unoccupied network command will always force the local zone to be in unoccupied mode and to use the
unoccupied setpoints. If the thermostat local override function is not locked out by configuration, the local user may initiate a
temporary local override to occupied as dictated by the temporary occupancy time configuration parameter setting.
Local occupancy state network command
When the thermostat receives a local occupancy state network command, the local PIR occupancy loop will now be enabled.
If the PIR devices do not then detect any movements, the occupancy of the zone will be stand-by mode.
As soon as the PIR device detects a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used. The room will then be in occupied mode until a door toggle is detected.
If a door toggle is detected, then the room switches to stand-by mode and the stand-by setpoints are used. If any occupants
are left in the room, local movements must be seen to resume the occupied mode.
While in stand-by mode, if no motion is detected in the zone for the entire unoccupied timer duration, then the room switches
to unoccupied mode and the unoccupied setpoints are used.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
•
25
24) VT7300 Networked fan coil application using 2 levels of occupancy with dual PIR sensors
Set-up and Configuration
Thermostat used
PIR used
BI2 Configuration
Stand-by timer value
Unoccupied timer value
Network interface used
VT73x5X5000(BorE)…( lodging models )
BI1 configured for remote PIR sensor and
COV-PIR-FCU-C-5000 accessory cover
Door dry contact
Not used
0.0 hours
Echelon or BACnet MS-TP
BACnet or Echelon Network
Remote PIR Sensor
Door Switch
Advanced network interface can be obtained when thermostats are fully
integrated to the reservation system
In these cases, the occupancy network commands state enumerations text
presented by a front end system can be expanded to better represent the
nature of the application.
Occupancy network commands state
Local Occupancy ( PIR active )
Occupied
Unoccupied
Front end system state text examples
Room rented PIR economy enabled
Room rented high comfort assured
Room not rented
Sequence of operation:
Occupied
Always
Occupied
Stand-By
Unoccupied Time
= 0 Hours
Unoccupîed
Time
Initial Network
Command = Unoccupied
PIR Movements Ignored
Network Command
= Local PIR Occupancy
Door Open/Close
Toggle Detected
First Movement Detected
by a PIR Device
Network Command
= Occupied
PIR Movements Ignored
Network Command
= Unoccupied
PIR Movements Ignored
At initial power-up, when the thermostat 24 Vac power supply is applied; if there is no occupancy network command received
by the thermostat and if the PIR device do not detect any movements, the initial occupancy of the zone will be stand-by mode.
Occupied state network command
At any time, an occupied network command will always force the local zone to be in occupied mode and to use the occupied
setpoints.
Unoccupied state network command
At any time, an unoccupied network command will always force the local zone to be in unoccupied mode and to use the
unoccupied setpoints. If the thermostat local override function is not locked out by configuration, the local user may initiate a
temporary local override to occupied as dictated by the temporary occupancy time configuration parameter setting.
Local occupancy state network command
When the thermostat receives a local occupancy state network command, the local PIR occupancy loop will now be enabled.
If the PIR devices do not then detect any movements, the occupancy of the zone will be stand-by mode.
As soon as the PIR device detects a movement or motion, the occupancy status switches to occupied and the occupied
setpoints are used. The room will then be in occupied mode until a door toggle is detected.
If a door toggle is detected, then the room switches to stand-by mode and the stand-by setpoints are used. If any occupants
are left in the room, local movements must be seen to resume the occupied mode.
At anytime, if the PIR device detects a local movement or motion, the occupancy status switches to occupied and the
occupied setpoints are used.
The local zone never goes into unoccupied mode and the unoccupied setpoints are never used.
26
Typical Detection Pattern for VI-PIR Lens
Horizontal
Angle (typical)
Vertical Angle
(typical)
Installation Tips
Tip Type
General Installation
Area Of Interest
PIR Connector
Security Screw
Tip Type
Initial Power Up &
Commissioning
Area Of Interest
PIR Warm up period
Visual indication (Status of PIR)
Explanation
Polarized connector is located at bottom left hand corner
of VT7000 series thermostat
A security screw has been provided in the thermostat
box. This screw should be carefully installed in the
intended mounting position located bottom center of
thermostat cover.
Explanation
PIR Sensor may take up-to 60 seconds after initial warm
up period to detect movement consistent with typical
detection pattern.
Visual indication of PIR activity for commissioning has
been provided via a blinking LEDs located on the
thermostat cover under the PIR lens. LEDs will be active
while occupant is in field of detection pattern for a period
of 30 minutes after initial power up.
27
VI-PIR Cover Installation
•
•
Remove security screw on the bottom of the current thermostat cover.
Open up by pulling on the bottom side of thermostat. (Fig. 3)
A)
Identify current thermostat model type:
Use appropriate cover accessory part number as identified on the first page by referring to the thermostat model
number
The male polarized PIR connector is located at bottom left corner of thermostat (Fig. 4)
•
•
B)
•
•
•
•
Installation:
Hinge new PIR thermostat cover into position (fig. 3).
Insert polarized connector into PIR female connector located on thermostat base (Fig 4)
Snap PIR thermostat cover into place and re-install the security screw
Make appropriate parameter settings related to your application within the configuration menu as identified in the
thermostat installation
Fig.3
• Electronic controls are static sensitive devices. Discharge yourself properly before manipulation and
installing the thermostat and its accessories.
• Short circuit or wrong wiring may permanently damage the thermostat or the equipment.
• All VT7000 series thermostats are to be used only as operating controls. Whenever a control failure could
lead to personal injury and/or loss of property, it becomes the responsibility of the user to add safety
devices and/or alarm system to protect against such catastrophic failures.
Specifications
Fig.4
PIR cover power requirements:
Operating conditions:
Storage conditions:
Sensor:
Dimensions with Thermostat:
Approximate shipping weight with Thermostat:
Agency Approvals:
UL
FCC
Industry Canada
CE
C-Tick
5 Vdc Max current draw of 7mA
0 °C to 50 °C ( 32 °F to 122 °F )
0% to 95% R.H. non-condensing
-30 °C to 50 °C ( -22 °F to 122 °F )
0% to 95% R.H. non-condensing
Local Passive Infra Red Sensor
4.94” x 3.38” x 1.13”
0.75 lb ( 0.34 kg )
UL 873 (US) and CSA C22.2 No. 24 (Canada), File E27734 with CCN
XAPX (US) and XAPX7 (Canada)
Compliant to CFR 47, Part 15, Subpart B, Class A (US)
ICES-003 (Canada)
EMC Directive 89/336/EEC (Europe Union)
AS/NZS CISPR 22 Compliant (Australia / New Zealand)
Supplier Code Number N10696
Drawing & Dimensions
Thermostat Dimensions
Fig.5