NX-595E NetworX IP Communication Module Installation

UC-331-UCX Dual Path
Communication Module
Quick Start Guide
P/N 230887 • ED 01 • ISS 13MAR17 ©2017 7 UTC Fire & Security Americas Corporation, Inc. All rights reserved.
Introduction
The UC-331-UCX is a Public Switched Telephone Network (PSTN)
replacement supporting Dual Path reporting with IP and cellular
communications. Monitoring Centres receive messages via UltraSync
servers and can remotely manage UC-331-UCX devices using the
UltraSync Web Portal.
Verify that your Monitoring Centre is UltraSync capable before attempting
to install the UC-331-UCX. The UC-331-UCX must be provisioned in the
UltraSync Web Portal by the Monitoring Centre to begin IP reporting.
UltraSync+ is an iOS and Android app allowing remote keyswitch arming
and disarming of the security panel.
The UC-331-UCX can be quickly installed as a simple PSTN replacement
product without any configuration. Connection to the alarm panel’s auxiliary
power and PSTN connection is all that is required.
If both keyswitch arming and static IP are not required, the UC-331-UCX
does not need any configuration to minimize onsite installation time.
Included in the Box
•
•
•
•
•
•
•
•
•
UC-331-UCX unit in enclosure
Tamper switch with lead
Jumper
Antenna
6P2C and 4P2C panel cables
ASIAL cable
Power and panel cable
(3) 2KΩ resistor, (3) 3.3KΩ resistors
UltraSync Quick Reference Guide (this document)
Important Note Before Proceeding
For detailed installation and product information, please download the
UC-331-UCX Installation Manual from the Interlogix Web site:
www.interlogix.com.au
2
rights reserved.
P/N 466-5246 • REVB • ISS 03JAN17
©2016 7 UTC Fire & Security Americas Corporation, Inc. All
Installing the UC-331-UCX
1. Request the Monitoring Centre to provision the UC-331-UCX in the
UltraSync Web Portal to enable back-to-base reporting.
2. Determine where to mount the UC-331-UCX. The selected location
should provide optimal cellular signal strength and wiring access to the
alarm panel.
Caution: Remove all power (AC and battery) to the security system before
proceeding. Failing to do so could result in possible damage to the product.
Polarity is not important for the dialer interface.
3. Wire the UC-331-UCX to the alarm panel as shown in Figure 1. If
ASIAL Serial is required, refer to next page for wiring diagram.
4. Reconnect the alarm panel power. Review the power requirements of
the whole alarm system including the current draw of the UC-331-UCX.
Reference the UC-331-UCX current draw in the specifications detailed
below. The alarm system backup battery must be capable of supplying
its existing load and the UC-331-UCX in the event of an AC power
failure. Recalculate the AUX power current draw to stay within the
alarm panel’s specifications.
5. For remote keyswitch arming and disarming of the panel with the
UltraSync+ application, additional wiring and configuration is required.
Refer to full UC-331-UCX Installation Manual.
P/N 466-5246 • REVA • ISS 13APR16
©2016 7 UTC Fire & Security Americas Corporation, Inc. All rights reserved
Connecting to Alarm Panels via ASIAL
Serial
Note that for Class 3 and Class 4 installations ASIAL Serial must be
used.
Alarm panels supporting the ASIAL Serial format are connected to BUS1A
and BUS1B:
•
PWR+ only connect this if the unit is being powered by the alarm
panel. If the unit is being supplied by its own plug-pack and battery,
then do not connect this pin.
•
BUS1A
connect to the RX connection on the alarm panel.
•
BUS1B
connect to the TX connection on the alarm panel.
•
0V
always connect this to 0V or GND on the alarm panel.
Note that depending on the panel type, the TX and RX connections should
be configured for RS-232 or TTL via BUS1 jumper as shown below:
RS232 – Set BUS1 jumper 2 & 3
MCM Icon Range
Concept 2000
Concept 3000
Example 1 – Wiring for an InnerRange
Concept
Pos
Tx
Rx
Neg
PWR+
BUSA
BUSB
0V
1
2
3
UC-331 Unit
4
rights reserved.
P/N 466-5246 • REVB • ISS 03JAN17
TTL – Set BUS1 jumper 1 & 2
Tecom Challenger
GE NetworX
Example 2 – Wiring for a Tecom
Challenger
+12
Tx
Rx
0V
PWR+
BUSA
BUSB
0V
1
2
3
UC-331 Unit
©2016 7 UTC Fire & Security Americas Corporation, Inc. All
Specifications
Power
Current
GPIO output current
Product Dimensions
Environmental
conditions
Panel Interface
Panel Formats
Remote Servicing
Cellular Interface
Cellular Frequency
Copyright
Voltage range 10VDC – 18VDC
12V
110mA average, 150mA peak
< 2V at 50mA
103 x 180 x 34mm
4.05 x 7.09 x 1.3inch
-10° to +70°C
+14° to +158°F
5% – 90% relative humidity non-condensing
Dial Capture, ASIAL Serial including Contact ID sub-format
(Challenger 10)
Ademco® ContactID, Fast
SIA 1/2/3
Upload download via:
- DLX 900 for NetworX
- EDS for Concord panels
- Titan for Challenger
3G+GPRS
850/900/1800/2100 MHz
© 2017 UTC Fire & Security Americas Corporation, Inc.
All rights reserved.
IOS is the registered trademark of Cisco Technology,
Inc. Android, Google and Google Play are registered
trademarks of Google Inc. iPhone, Apple, iTunes are
Trademarks registered trademarks of Apple Inc. App Store is a
and patents service mark of Apple Inc.
All other trademarks are the property of their respective
owners.
Manufacturer
Placed on the market by:
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Use this product only for the purpose for which it was
designed. For the latest product information, contact
Intended Use your local supplier or visit us online at
http://www.interlogix.com.au
Regulatory Approvals
P/N 466-5246 • REVA • ISS 13APR16
©2016 7 UTC Fire & Security Americas Corporation, Inc. All rights reserved
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by UTC Fire
Regulatory and Security could void the user’s authority to operate the
Information equipment.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may
cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de
licence standard RSS (s). Son fonctionnement est soumis aux
deux conditions suivantes: (1) cet appareil ne doit pas
provoquer d'interférences et (2) cet appareil doit accepter toute
interférence, y compris celles pouvant causer un mauvais
fonctionnement de l'appareil.
In accordance with FCC requirements of human exposure to
radiofrequency fields, the radiating element shall be installed
such that a minimum separation distance of 20 cm is maintained
from the general population.
FCC: XPYLISAU200
IC: 8595A-LISAU200
This Class B digital apparatus complies with Canadian ICES-3B.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
6
rights reserved.
P/N 466-5246 • REVB • ISS 03JAN17
©2016 7 UTC Fire & Security Americas Corporation, Inc. All
UTC Fire & Security Americas Corporation, Inc. hereby
declares that this device is in compliance with the
applicable requirements and provisions of one or more of
EU directives
the Directives 1999/5/EC, 2015/30/EU and 2015/35/EU.
For more information see: www.utcfireandsecurity.com or
www.interlogix.com
2012/19/EU (WEEE directive): Products marked with this
symbol cannot be disposed of as unsorted municipal
waste in the European Union. For proper recycling, return
this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated
collection points. For more information see:
www.utcfssecurityproducts.eu/recycle/
Contact For contact information, visit us online at
information www.interlogix.com.au
Customer Interlogix Australia www.interlogix.com.au
support +61392391200
Important information
Copyright
The contents of this publication may not be reproduced in any part or as a whole, stored,
transcribed in an information retrieval system, translated into any language, or transmitted in
any form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or
otherwise, without the prior written permission.
Trademarks
All products, company, brand names are trademarks or registered trademarks of their respective
companies. They are used for identification purpose only. Specifications are subject to be
changed without prior notice.
Limitation of Liability
To the maximum extent permitted by applicable law, in no event will UTCFS be liable for any
lost profits or business opportunities, loss of use, business interruption, loss of data, or any other
indirect, special, incidental, or consequential damages under any theory of liability, whether
based in contract, tort, negligence, product liability, or otherwise. Because some jurisdictions do
not allow the exclusion or limitation of liability for consequential or incidental damages the
preceding limitation may not apply to you. In any event the total liability of UTCFS shall not
exceed the purchase price of the product. The foregoing limitation will apply to the maximum
extent permitted by applicable law, regardless of whether UTCFS has been advised of the
possibility of such damages and regardless of whether any remedy fails of its essential purpose.
Installation in accordance with this manual, applicable codes, and the instructions of the
authority having jurisdiction is mandatory.
P/N 466-5246 • REVA • ISS 13APR16
©2016 7 UTC Fire & Security Americas Corporation, Inc. All rights reserved
While every precaution has been taken during the preparation of this manual to ensure the
accuracy of its contents, UTCFS assumes no responsibility for errors or omissions.
Product Warnings
YOU UNDERSTAND THAT A PROPERLY INSTALLED AND MAINTAINED
ALARM/SECURITY SYSTEM MAY ONLY REDUCE THE RISK OF EVENTS SUCH AS
BURGLARY, ROBBERY, FIRE, OR SIMILAR EVENTS WITHOUT WARNING, BUT IT IS NOT
INSURANCE OR A GUARANTEE THAT SUCH EVENTS WILL NOT OCCUR OR THAT
THERE WILL BE NO DEATH, PERSONAL INJURY, AND/OR PROPERTY DAMAGE AS A
RESULT.
THE ABILITY OF INTEROGIX’S PRODUCTS, SOFTWARE OR SERVICES TO WORK
PROPERLY DEPENDS ON A NUMBER OF PRODUCTS AND SERVICES MADE AVAILABLE
BY THIRD PARTIES OVER WHICH INTERLOGIX HAS NO CONTROL AND FOR WHICH
INTERLOGIX SHALL NOT BE RESPONSIBLE INCLUDING, BUT NOT LIMITED TO,
INTERNET, CELLULAR AND LANDLINE CONNECTIVITY; MOBILE DEVICE AND
OPERATING SYSTEM COMPATIBILITY; MONITORING SERVICES; ELECTRONMAGNETIC
OR OTHER INTERFERENCE, AND PROPER INSTALLATION AND MAINTENANCE OF
AUTHORIZED PRODUCTS (INCLUDING ALARM OR OTHER CONTROL PANEL AND
SENSORS).
ANY PRODUCT, SOFTWARE, SERVICE OR OTHER OFFERING MANUFACTURED, SOLD
OR LICENSED BY INTERLOGIX, MAY BE HACKED, COMPROMISED AND/OR
CIRCUMVENTED AND INTERLOGIX MAKES NO REPRESENTATION, WARRANTY,
CONVENANT OR PROMISE THAT ITS PRODUCTS (INCLUDING SECURITY PRODUCTS),
SOFTWARE, SERVICES OR OTHER OFFERINGS WILL NOT BE HACKED, COMPROMISED
AND/OR CIRCUMVENTED.
INTERLOGIX DOES NOT ENCRYPT COMMUNICATIONS BETWEEN ITS ALARM OR
OTHER CONTROL PANELS AND THEIR WIRELESS OUTPUTS/INPUTS INCLUDING BUT
NOT LIMITED TO, SENSORS OR DETECTORS UNLESS REQUIRED BY APPLICABLE LAW.
AS A RESULT THESE COMMUNICATIONS MAY BE INTERCEPTED AND COULD BE USED
TO CIRCUMVENT YOUR ALARM/SECURITY SYSTEM.
THE EQUIPMENT SHOULD ONLY BE OPERATED WITH AN APPROVED POWER ADAPTER
WITH INSULATED LIVE PINS.
DO NOT CONNECT TO A RECEPTACLE CONTROLLED BY A SWITCH.
THIS UNIT INCLUDES AN ALARM VERIFICATION FEATURE THAT WILL RESULT IN A
DELAY OF THE SYSTEM ALARM SIGNAL FROM THE INDICATED CIRCUITS. THE TOTAL
DELAY (CONTROL UNIT PLUS SMOKE DETECTORS) SHALL NOT EXCEED 60 SECONDS.
NO OTHER SMOKE DETECTOR SHALL BE CONNECTED TO THESE CIRCUITS UNLESS
APPROVED BY THE LOCAL AUTHORITY HAVING JURISDICTION.
WARNING: The equipment should only be operated with an approved power adapter with
insulated live pins.
Caution: Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries
according to the instructions. Contact your supplier for replacement batteries.
Warranty Disclaimers
INTERLOGIX HEREBY DISCLAIMS ALL WARRANTIES AND REPRESENTATIONS,
WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING ANY IMPLIED
WARRANTIES, THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
8
rights reserved.
P/N 466-5246 • REVB • ISS 03JAN17
©2016 7 UTC Fire & Security Americas Corporation, Inc. All
PARTICULAR PURPOSE.
(USA only) SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES,
SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. YOU MAY ALSO HAVE OTHER
LEGAL RIGHTS THAT VARY FROM STATE TO STATE.
INTERLOGIX DOES NOT MAKE ANY CLAIMS OR WARRANTIES TO YOU OF ANY KIND
REGARDING ANY PRODUCT, SOFTWARE OR SERVICE’S POTENTIAL, ABILITY, OR
EFFECTIVENESS TO DETECT, MINIMIZE, OR IN ANYWAY PREVENT DEATH, PERSONAL
INJURY, PROPERTY DAMAGE, OR LOSS OF ANY KIND WHATSOEVER.
INTERLOGIX DOES NOT REPRESENT TO YOU THAT ANY PRODUCT (INCLUDING
SECURITY PRODUCTS), SOFTWARE, SERVICE OR OTHER OFFERING MAY NOT BE
HACKED, COMPROMISED AND/OR CIRCUMVENTED.
INTERLOGIX DOES NOT WARRANT THAT ANY PRODUCT (INCLUDING SECURITY
PRODUCTS), SOFTWARE OR SERVICE MANUFACTURED, SOLD OR LICENSED BY
INTERLOGIX WILL PREVENT, OR IN ALL CASES PROVIDE ADEQUATE WARNING OF OR
PROTECTION FROM, BREAK-INS, BURGLARY, ROBBERY, FIRE, OR OTHERWISE.
INTERLOGIX DOES NOT WARRANT TO YOU THAT ITS SOFTWARE OR PRODUCTS WILL
WORK PROPERLY IN ALL ENVIRONMENTS AND APPLICATIONS AND DOES NOT
WARRANT ANY PRODUCTS AGAINST HARMFUL ELECTROMAGNETIC INTERFERENCE
INDUCTION OR RADIATION (EMI, RFI, ETC.) EMITTED FROM EXTERNAL SOURCES
INTERLOGIX DOES NOT PROVIDE MONITORING SERVICES FOR YOUR
ALARM/SECURITY SYSTEM (“MONITORING SERVICES”). IF YOU ELECT TO HAVE
MONITORING SERVICES YOU MUST OBTAIN SUCH SERVICE FROM A THIRD PARTY
AND INTERLOGIX MAKES NO REPRESENTATION OR WARRANTY WITH RESPECT TO
SUCH SERVICES INCLUDING WHETHER OR NOT THEY WILL BE COMPATIBLE WITH THE
PRODUCTS, SOFTWARE OR SERVICES MANFUFACTURED, SOLD OR LICENSED BY
INTERLOGIX.
Disclaimer
THE INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
UTC ASSUMES NO RESPONSIBILITY FOR INACCURACIES OR OMISSIONS AND
SPECIFICALLY DISCLAIMS ANY LIABILITIES, LOSSES, OR RISKS, PERSONAL OR
OTHERWISE, INCURRED AS A CONSEQUENCE, DIRECTLY OR INDIRECTLY, OF THE
USE OR APPLICATION OF ANY OF THE CONTENTS OF THIS DOCUMENT. FOR THE
LATEST DOCUMENTATION, CONTACT YOUR LOCAL SUPPLIER OR VISIT US ONLINE AT
WWW.INTERLOGIX.COM.AU
This publication may contain examples of screen captures and reports used in daily operations.
Examples may include fictitious names of individuals and companies. Any similarity to names
and addresses of actual businesses or persons is entirely coincidental.
The illustrations in this manual are intended as a guide and may differ from your actual unit as
ZeroWire is continually being improved.
Intended Use
Use this product only for the purpose it was designed for; refer to the data sheet and user
documentation. For the latest product information, contact your local supplier or visit us online
at www.utcfireandsecurity.com.
The system should be checked by a qualified technician at least every 3 years and the backup
battery replaced as required.
P/N 466-5246 • REVA • ISS 13APR16
©2016 7 UTC Fire & Security Americas Corporation, Inc. All rights reserved
Advisory messages
Advisory messages alert you to conditions or practices that can cause unwanted results. The
advisory messages used in this document are shown and described below.
WARNING: Warning messages advise you of hazards that could result in injury or loss of life.
They tell you which actions to take or to avoid in order to prevent the injury or loss of life.
Caution: Caution messages advise you of possible equipment damage. They tell you which
actions to take or to avoid in order to prevent the damage.
Note: Note messages advise you of the possible loss of time or effort. They describe how to
avoid the loss. Notes are also used to point out important information that you should read.
LIABILITY
The services and products provided by UHS, when installed and commissioned, are only
intended to provide a communications path between the equipment and a supervision center to
the extent that is reasonably practicable by use of such goods and services.
DISCLAIMER
The manufacturer or his agents disclaim responsibility for any damage, financial loss or injury
caused to any equipment, property or persons resulting from any use of this equipment. The
manufacturer is not liable for any purely economic loss arising from any use of this equipment.
All responsibility and liability in the use of UHS products are assumed by the user.
This unit is designed to be used in customer premises. Use of this equipment in other locations
may void warranty. This unit is not intended for use in marine environments or water borne
vessels.
UHS may make changes to features and specifications at any time without prior notification in
the interest of ongoing product development and improvement.
USER OR BYSTANDER EME PROXIMITY LIMITATION
The antenna must be located greater than 20cm from any user or bystander.
LICENSE INFORMATION
This product uses FreeRTOS V8.2.0, the FreeRTOS source code can be obtained by a request in
writing to UHS Pty Ltd, PO Box 6264, South Sydney Business Hub, Alexandria, NSW, 2015, Australia
10
rights reserved.
P/N 466-5246 • REVB • ISS 03JAN17
©2016 7 UTC Fire & Security Americas Corporation, Inc. All
Download PDF

advertising