FW881 Extra Large Integrated Freezer

FW881 Extra Large Integrated
Freezer
Manual for Installation, Use and Maintenance
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.eu
Important
The manufacturer cannot be held responsible for injuries or losses
caused by incorrect use or installation of this product. Please note
that we reserve the right to invalidate the guarantee supplied with this
product following incorrect installation or misuse of the appliance.
This appliance is not designed to be used by people (including
children) with reduced physical, sensorial or mental capacity, or
who lack experience or knowledge about it, unless they have had
supervision or instructions on how to use the appliance by someone
who is responsible for their safety.
Under no circumstances should any external covers be removed for
servicing or maintenance except by suitably qualified personnel.
Appliance information:
Please enter the details on the appliance rating plate below for
reference, to assist CDA Customer Care in the event of a fault with
your appliance and to register your appliance for guarantee purposes.
Appliance Model
Serial Number
CE Declarations of Conformity:
This appliance has been designed, constructed and marketed in
compliance with safety requirements of EEC Directive 2006/95/EEC
(Low voltage) and requirements of EMC Directive 2004/108/EEC.
2
This appliance has been manufactured to the strictest standards and
complies with all applicable legislation, including Electrical safety (LVD)
and Electromagnetic interference compatibility (EMC). Parts intended
to come into contact with food conform to EEC/89/109.4
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed of as
urban waste. The refrigeration system contains insulating gases and
refrigerants, which require specialised waste disposal. The valuable
materials contained in this appliance can be recycle. It must be taken
to a special local authority differentiated waste collection centre or to
a dealer providing this service.
Before disposing of an old appliance, remove the door seals, latch or
bolt lock to avoid the risk of child entrapment.
Disposing of a household appliance separately avoids possible
negative consequences for the environment and health deriving from
inappropriate disposal and enables the constituent materials to be
recovered to obtain significant savings in energy and resources. As a
reminder of the need to dispose of household appliances separately,
the product is marked with a crossed-out wheeled dustbin.
3
Before First Use
You must allow the freezer to settle for at least twenty four hours
prior to switching the power on.
It is recommended that you clean the interior of the appliance prior to
first use, using a solution of bicarbonate of soda and warm water and
then thoroughly drying the interior.
The freezer may have an odour to it at first use. This will
disappear as the appliance cools.
Please note:
• The appliance will work continuously until it comes down to the
correct temperature.
• If the appliance is switched off, you should allow five minutes
before switching it on again to prevent unnecessary damage to the
compressor.
4
Controls and Use
S
S
4
5
2
1
3
OFF
1
3
4
5
2
fig. 1
1.Thermostat dial
The thermostat automatically keeps the internal temperature at a
constant level. The temperature is regulated by the thermostat dial,
located on the freezer control panel. To change the temperature,
turn the dial anti-clockwise from 1 (highest temperature) to 5 (coldest
temperature). We recommend that you start with the appliance set
to position 3.
Do not turn the dial beyond the maximum. To switch the freezer
off, turn the dial anticlockwise to the minimum position.
2.Super freeze button
This freezer is equipped with a super freeze function. This allows
the freezer compressor to run continuously and so freezes food
more quickly. To select this function, press the button briefly, the
super freeze indicator light (5) illuminates. To switch the function
off, press the button and hold it for three seconds, the indicator light
goes out again.
Note that this function will switch itself off automatically after 24
hours.
3.Power indicator light
This green light will illuminate when the freezer is switched on.
5
4.Over temperature indicator light
This red light will illuminate when the temperature inside the freezer
is too high. This may illuminate after the door has been opened,
or when fresh food is added and should switch off again once the
temperature within the freezer has stabilised.
5.Super freeze indicator light
This yellow light will illuminate when the super freeze function has
been switched on with the super freeze switch (2).
Use
• The freezer compartments are designer to store only frozen food.
• |Never put hot or warm foods in the freezer, allow them to cool fully
before putting them into the freezer.
• Follow the instructions on the packaging for storage of frozen food.
If no information is provided, foods should not be stored for more
than three months after the purchase date.
• Never put carbonated drinks into the freezer as the carbon dioxide
may expand, causing and explosion.
6
Defrosting the Freezer
Do not use heaters or defrosting sprays in this appliance.
• Never use any metallic or sharp objects to remove the ice as this
could damage the lining.
• The freezer compartment should be defrosted regularly to ensure
the most efficient running of the freezer.
• Once the ice is more than 5mm thick, the freezer should be
defrosted.
• First remove the freezer drawers.
• To speed up the process, place a bowl of warm water in the base of
the freezer compartment.
Once defrosting is complete, dry the inside of the freezer
compartment with a sponge or clean cloth thoroughly. Then reconnect the mains power supply.
• Clean the drawers separately by hand using soap and water. Do not
put them in a dishwasher.
7
Troubleshooting
If you have any problems with your appliance, you should check
the troubleshooting prior to calling CDA Customer Care to prevent
unnecessary service calls and potential cost.
If the appliance is not working
• Check there is power to the appliance.
• The house fuses are intact and the fuse in the plug has not blown.
• The thermostat is not set to 0 (off position).
• The plug socket is functioning fine. To check this, plug another
electrical appliance in to see if the socket is working.
• The temperature of the room is adequate (10°C or above).
If the appliance is working, but not very well
• The appliance is not overloaded.
• The thermostat is set to an appropriate temperature.
• The door is closing properly.
• The cooling system at the rear of the appliance is clean and free of
dust, and not touching the rear wall.
• There is enough ventilation at the side and rear walls.
• The temperature of the room is adequate (10°C or above).
If the appliance is noisy
• The appliance is level and stable.
• The side and rear walls are clear, and there is nothing resting on the
appliance.
• The cooling gas in the refrigerator will make a slight bubbling noise,
even when the compressor is not running.
8
If there is water in the lower part of the refrigerator compartment
• The drain hole in the channel at the back of the compartment is
clear.
9
Installation and Ventilation
This appliance must never be installed close to heat sources i.e.
heating elements, cookers or in damp places
The diagram shows the ventilation requirements for your product.
Failure to provide adequate ventilation can lead to increased running
costs and
premature failure and may invalidate the warranty provided with the
product.
560-570
550 min
545
57
17701788
1770
min. 30
45
540
= airflow
fig. 2
10
Ventilation
The main consideration when installing any refrigeration unit into
a fitted kitchen is ventilation. The heat removed from the cooling
compartment needs to be dissipated into the atmosphere. Incorrect
ventilation can lead to premature compressor failure, excessive power
consumption and total system failure. For products intended to be
installed into a tall housing unit, the following requirements need to be
met: Important
Please follow the instructions to install this unit
An air intake
should be
provided
somewhere in
the cabinet run to
allow free air in.
In this example,
a plinth vent is
shown underneath
the refrigerator .
The top of the cabinet needs to be
vented into the room
Refrigerator
outline
Recommended size of vent opening:
500 x 35mm
If the furniture does not allow free air
into the room then a plinth vent, or other
means of ventilation needs to be provided to ensure a natural flow of air
A thin section of
the plinth can be
removed to allow
air into the unit
(recommended
600mm x 10mm)
Min 30mm
There should be space at the rear of the
cabinet to allow cool air to be drawn over
the condenser.
Recommended:
500 x 35mm
300
300
plan view of cut out and ventilation gaps
A hole should be cut in the supporting
shelf, as shown below
fig. 3
11
The open channel at the rear is clearly shown. For the correct
operation of the appliance it is important that the top of the housing
unit is not blocked off. A channel depth of 40-50mm is normal with
most units.
A hole is shown in the base shelf of the unit; this allows air to be
drawn over the compressor & heat exchange. Some installers fit a
decorative plinth vent. In most cases this is not required, but is a
welcome aesthetic addition.
As a rule, the more air can get in, the better and more efficient the
operation of the product.
12
Reversing the Door
fig. 4
It is possible to reverse the door on
this appliance, if required. To do so,
follow the steps below:
1.
2.
3.
4.
5.
Loosen the top hinge fixing screws
and remove the top hinge, taking
care to support the weight of the
door.
Lift the door from the bottom hinge
and place on a soft surface to
protect the door from damage.
Refit the hinge taken from the top
to the opposite lower corner, as in
figure 4.
Replace the door and refit the
hinge taken from the lower corner
to the opposite top corner.
Adjust the hinges to ensure the
door is aligned correctly.
13
Mounting the Fascia
Door
• Using a screwdriver, fix the mounting
brackets to the appliance door, as
shown in figure 5.
• Position the appliance within the unit.
Ensure that there is a gap of 3 to 4 mm between the non-hinged
side and the cabinet wall.
• Locate the slider in the bracket and fix
the slider to the fascia door 20 to 22 mm from the edge of
the fascia as shown in figure 6, ensuring that the slider is positioned
centrally and horizontally within the bracket. Tighten securely
by hand.
• Fill the gap on the non-hinged side
with the seal strip provided, as shown in figure 7.
x4
fig. 5
x4
20 mm
fig. 6
door gasket
14
fig. 7
Electrical Information
Warning! This appliance must be earthed.
Green and Yellow to Earth
A
13 Amp
Brown to Liv e
B
13 Amp fuse
Cord Clamp
fig. 13
Blue to Neutra l
The mains lead of this appliance has been fitted with a BS 1363A 13
amp fused plug. To change a fuse in this type of plug, follow the steps
below:
1. Remove the fuse cover and fuse.
2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the
fuse cover.
3. Replace fuse cover.
Important: Do not use the appliance without the fuse cover in
position.
How to connect an alternative plug
If the fitted plug is not suitable for your socket outlet, then it should
be cut off and disposed of safely to avoid possible shock hazard. A
suitable alternative plug of at least 13 Amp rating to BS 1363 should be
used.
15
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in
your plug, proceed as follows:• The wire which is coloured GREEN and YELLOW must be connected
to the terminal which is marked with letter (E) or by the Earth symbol
or coloured GREEN and YELLOW.
• The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter (N), or coloured BLACK.
• The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter (L) or coloured RED.
If in doubt regarding the electrical connection of this appliance,
consult a qualified electrician. Do not shorten the supply cable, the
appliance may require removing for servicing.
N.B. Ensure that the plug socket is situated in an easily accessible
place after installation.
16
17
18
19
To contact our Customer Care Department, or for Service,
please contact us on the details below.
Passionate
about
style
Please contact our Customer
Care Department
for Service
on the details below.
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
Download PDF

advertising