Speed Dome Camera Controller Operation manual

Speed Dome Camera Controller
Operation manual
Please carefully read this operation manual before using this keyboard controller
Controller packing list:
1. keyboard controller
1 PCS
2. Power supply DC 12V(DC9V)
1 PCS
3. RJ 45 Cable
1 PCS
4. RJ45 Interface box
1 PCS
5. Operation Manual
1 PCS
6. Quality certificate
1 PCS
Attention Item:
Please read the keyboard operation manual carefully
before using it.
The keyboard is served with 12V (9V) DC power supply.
Please make sure the voltage and polarity before the
power supply is switched on.
Do not place the keyboard under the rain or on wet place
to avoid short circuit or electrical shock.
The keyboard is high precision electronic device; please
do not open the case, to avoid any possible breakdown.
The keyboard integrates with multiple protocols; please
choose the appropriate protocol and baud rate. Please
notice the LCD will display the chosen protocol and baud
rate for moment.
I. General introduction
The keyboard controller is professional equipped together with terminal
receivers such as the intelligent Speed Dome and the decoder etc. Taking
the EIA/RS-485 electrical interface between the keyboard and the receiver,
one keyboard can control as much as 32 speed dome and decoders and
the maximum communication distance between the keyboard and the
receiver is up to 1.2 km without bus-mastering. The keyboard controller
makes it more convenient to control the speed dome camera and the
terminal decoder, hence to control the camera constant speed pan tilt, lens,
light, rain brush and so on.
Main Functions:
Dome camera or decoder address setting range:0~9999
Users can set password, keyboard locking time, communication rate
and protocol by using the operation menu.
With functions to control the dome camera: such as camera
background light compensation on/off.
Operate the dome camera at different speed setting, speed
switching smooth and even
Control the pan tilt auto line scan, speed and direction can be set as
well
Set or call the set points and cruise tracks of the dome camera.
Altogether 999 preset points and 1--6 cruise tracks can be set. Each
track involves 16 preset position and the dwelling time and call
speed upon each
point can be set as well.
Manually or automatically control the dome camera, and change the
internal function settings of particular camera by call the menu of
the camera. .
Manually control the focus, zoom and iris of the camera.
Provide on line control help
Intelligent design, easy operation, all setting can be done with the
operation menu.
II. Keyboard Panel introduction:
1. The Front Panel and Buttons description (Figure 1-1)
There are speed joystick, buttons and LCD on the front panel of the
keyboard. The display is used to show the status of the system and
operation information. The joystick controls the upward, downward,
leftward and rightward speed motion of the speed dome. The description
of buttons is as follows:
(Figure1-1)
NO.+SHOT+ON :Preset point
NO.+SHOT+ACK : Call preset point
NO.+SHOT+OFF :Cancel preset points
NO.+SHOT+ENTER :Call cruise
NO.+SHOT+F1:Stop cruise
NO.+SHOT+F2: Delete cruise track
WIDE:Zoom out
TELE:Zoom in
FAR:Focus far
NEAR:Focus near
F1:Auxiliary control button
OPEN:Iris open
CLOSE:Iris close
F2: Auxiliary control button
SET:Menu entering
ENTER:OK
ESC :Exit menu
2. Rear Panel (Figure 2)
a). Power input connector (DC12V): DC12V power supply.
b). Communication connector (RS485): RS485 signal output.
c). Integration connector (RJ45): The port includes the output of RS485 and
input of the power supply, the port is connected to adapter box by specific
cable.
d). PC connector (PC/RS232): Used to connect the PC RS232 port,
implement control with the PC together.
III. Keyboard setting:
Figure 1
Figure 2
1.
2.
智能球型摄影机键盘控制器
Keyboard is with a sound ‘di—‘when power is on, 1.5 seconds later,
keyboard start normal working status and display the latest dome number,
protocol, baud rate. If the user set password, then password is required
before entering into normal work status, refer to figure 1, input six digits
password, click enter, start work, refer to figure 2.
If there is something not sure, press F1 for help information.
Figure 3
3. Parameter setting:press【Set】,then【Enter】to change some parameter.
The chosen setting g will be glittering , shown as figure 3,press【F2】 for
downward or【F1】upward for selecting ,press 【Enter】to enter into the related
choices for setting
Figure 4
1)、Dome number setting:when choose “1.Dome ID”, press【Enter】,come
to new dome number。Press 【Esc】to delete the wrong number and input
again。When finish the input, press【Enter】,system will ask: Save or not?
Press 【Enter】to save the dome number,,system returns to the last
menu or press【Esc】 returns to the last menu without saving the setting.
Figure 5
2)、Protocol setting :when choose “2.Protcol”, press 【Enter】,enter into
protocol for selecting, eight protocols for selection, press 【F2】downward
or 【F1】upward for selection,the chosen item will be glittering, if press
【Enter】,system will ask save or not, press【Enter】 to save the
7
parameter, press 【Esc】
,system returns to the last menu. Shown as
Figure 5
Figure 6
3)、Baud rate setting:press“3.Baudrate”, press【Enter】to start the rate
selection shown as figure 7. Four rates altogether, press 【F2】downward
or【F1】upward to make the selection,the chosen item will be glittering,
Press【Enter】for system to save the setting or press 【Esc】for system
return to the last menu .Shown as Figure 6.
igure 7
Figure 8
4)、Password setting :chose “4.Password”, press【Enter】,system will ask
for the old password, upon verified of the old password, system comes to
the next setting step, shown as figure 7, if input the wrong password,
press【Enter】or 【Esc】to input again. When enter into the system, refer
to press the figure 8,【F2】for downward or【F1】upward to make the
selection.
Figure 9
8
智能球型摄影机键盘控制器
a)、“1、On”is the password for starting the machine, when the item blinks,
press【Enter】,system goes to next step setting, press 【F2】downward
or【F1】upward to make the choice, shown as Figure 9.
Figure 10
①、“1.Lock time Set”blinks,press 【Enter】to enter into keyboard locking
time setting,shown as figure 10, 99 minute is the biggest figure, if input
wrong, press【Esc】to cancel ,press 【Enter】to save the right figure,
and system returns to the last menu, or
press【Esc】to cancel the setting and system returns to the last menu as
well.
Figure 11
②、“2、Password Set” blinks, press 【Enter】system enters into new
password setting, and users will be asked to input the new password,
press 【Esc】to cancel the wrong input, press【Enter】for system to save
the right one, and return to the last menu, or press【Esc】to return to the
last menu without saving the parameter.。
Figure 12
b)、“2、Off”is the password for close the machine, when the item
blinks, press【Enter】,system will ask to use the password or not,
shown as figure 12, if press【Enter】, the password close then, the
keyboard lock is closed as well.
7
Figure 13
Figure 14
Figure 15
5)、Cruise tracking set:input track number,(only up to 6 digits More than 6
will be invalid input)shown as figure 13,press 【Enter】to set the cruising
point setting,(up to 16 only),press【Enter】after inputting the cruise track,
shown as figure 14,system start to edit the tracking points, shown as
figure 15.,press 【Enter】when finish the edition, and press【Enter】to
save the parameter and return to the last menu or press 【Esc】
otherwise.
Figure 16
6)、Button sound switch :“On”blinks ,press 【Enter】,system will ask to
save or not, press【Enter】to save the parameter and sound is open,
press 【Esc】,system directly returns to the last menu ; when “Off”blinks,
press 【Enter】system will ask to save or not, press【Enter】to save the
setting, sound off, system returns to the last menu, or press 【Esc】
otherwise , shown as figure 16
8
智能球型摄影机键盘控制器
Figure 17
7)、Backlight switch:“On”blinks ,press 【Enter】,press 【Enter】to save
backlight is on, otherwise, press 【Esc】 “Off”blinks ,press 【Enter】
to save backlight is off..
14、Dome camera function control and its parameter setting
(special control description)
Control function varies based on different camera.
Item marked with “*”are with memory function when the dome is
off
power.
To the cameras with menu, press “ NO.+SHOT+ACK ” to open it, or
“NO.+SHOT+ON ”to close the menu. If the camera is with menu and it is
on:
1. Use [WIDE]/[TELE]to scroll up and down to choose the menu item.
2. Use [FAR]/[NEAR]to change the menu item status
3. When the menu setting is ok, to close the menu as per the table shown
instruction.
4. Please refer to the dome operation manual for special cases.
Keyboard operation
No.
Control Item
No. +SHOT+ACK
No. +SHOT+ON
51
52
Pan-tilt
Compensation
Control
53
Enable line-scanning
(low-speed)
Enable line-scanning
(middle-speed)
Enable line-scanning
(high-speed)
Set starting point of
scanning
Set ending point of
scanning
Power on
Power off
on
Off
on
off
on
off
on
off
Start cruise track
58
Video Camera
Power Control
Background
Light
Compensation
*
Zero
Illumination
Screen
Display *
Digital Zoom *
59
FOCUS
Auto
Manually
60
61
IRIS
White Balance
Auto
Auto
Manually
Manually
54
55
56
57
7
62
63
100
95
96
97
98
99
Mode
Home position
Dwell
time
setting for the
Home position
function
Indoor
ATW
On
1min
2min
4min
8min
10min
outdoor
One Push WB
off
15、Use the Joystick to Control the Speed Dome Camera:
You can use the speed joystick to control the Pan/Tilt
direction and speed of
the dome of the camera randomly. The speed of pan/tilt is decided by the angle of
the joystick you operate at (Figure18). Change the tilting angle of the joystick you
can adjust the speed evenly and the camera can be focused automatically in the
course of scan to keep images being distinct.
(Figure 18)
8
智能球型摄影机键盘控制器
V.
Installation and Connection:
Attention: Please read the operation manual of the keyboard and the speed dome
carefully before connecting wires. Any incorrect connections can cause
permanent damage of the device. When connecting wires, first switch off the
power supply of all devices. The communication wires between devices should be
shielded twisted cable. When installing cables they should be far away from high
voltage lines or other possible interference circuits as much as possible.
1. Integrative connection:
(Figure 19)
Refers to the control output of the
keyboard RS485 and the power
input go through the interface box
first then the single RJ45 cable is
connected to the keyboard RJ45
port.
Figure 19
2. Normal connection :( Figure 20)
Refers to the RS485 control output
and power output are directly
connected to the keyboard relative
ports.
F
Figure 20
7
3.Connect to PC(Figure 21):Refers to the keyboard and computer can be
connected together to control the dome camera.
Figure 21
VI. Technical Specifications:
Communication between Speed Dome Camera and the Controller:Port to
multi-port and half duplex
function.
Communication mode: RS-485/PC RS 232
Baud Rate of Communication:Four baud rates i.e. 2400Bps, 4800Bps,
9600Bps and 19200Bps.
Distance of Communication:1200 M in maximum
Power Supply:DC12V/800 mA (DC9V/100mA)
Number of Controlled Speed Dome Camera up to 32.
Size:95mm(H) × 205mm(L) ×205mm(W)
Weight:1.2 Kg
8
Download PDF

advertising