NC6I Series
User Manual
NO. G03-NC6I-F
Revision: 2.0
Release date: December 27, 2017
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize
pollution and ensure environment protection of mother earth, please recycle.
i
TABLE OF CONTENT
ENVIRONMENTAL SAFETY INSTRUCTION ....................................................................... iii
USER’S NOTICE .................................................................................................................. iv
MANUAL REVISION INFORMATION ................................................................................... iv
ITEM CHECKLIST ................................................................................................................ iv
CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD
1-1 PRODUCT FEATURES .......................................................................................... 1
1-2 SPECIFICATION .................................................................................................... 2
1-3 MAIN BOARD DIAGRAM ....................................................................................... 3
CHAPTER 2 HARDWARE INSTALLATION
2-1 LOCATION OF INTERNAL JUMPER AND CONNECTOR...................................... 5
2-2 INTERNAL JUMPER AND CONNECTOR SETTING .............................................. 6
2-2-1 CONNECTORS ......................................................................................... 9
2-2-2 HEADERS ................................................................................................. 13
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERING SETUP................................................................................................. 18
3-2 BIOS MENU SCREEN ............................................................................................ 18
3-3 FUNCTION KEYS................................................................................................... 19
3-4 GETTING HELP...................................................................................................... 20
3-5 MEMU BARS.......................................................................................................... 20
3-6 MAIN MENU ........................................................................................................... 20
3-7 ADVANCED MENU ................................................................................................ 21
3-8 CHIPSET MENU..................................................................................................... 31
3-9 BOOT MENU .......................................................................................................... 35
3-10 SECURITY MENU .................................................................................................. 37
3-11 TURBOOC MENU .................................................................................................. 37
3-12 SAVE & EXIT MENU .............................................................................................. 40
ii
Environmental Safety Instruction

Avoid the dusty, humidity and temperature extremes. Do not place the product in
any area where it may become wet.

0 to 60 centigrade is the suitable temperature. (The figure comes from the request
of the main chipset)

Generally speaking, dramatic changes in temperature may lead to contact
malfunction and crackles due to constant thermal expansion and contraction from
the welding spots’ that connect components and PCB. Computer should go
through an adaptive phase before it boots when it is moved from a cold
environment to a warmer one to avoid condensation phenomenon. These water
drops attached on PCB or the surface of the components can bring about
phenomena as minor as computer instability resulted from corrosion and oxidation
from components and PCB or as major as short circuit that can burn the
components. Suggest starting the computer until the temperature goes up.

The increasing temperature of the capacitor may decrease the life of computer.
Using the close case may decrease the life of other device because the higher
temperature in the inner of the case.

Attention to the heat sink when you over-clocking. The higher temperature may
decrease the life of the device and burned the capacitor.
iii
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED
OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN
PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIES AND WE
DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME
WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY
KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA,
INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.
Manual Revision Information
Reversion
2.0
Revision History
Second Edition
Date
December 27, 2017
Item Checklist





Motherboard
DVD for motherboard utilities
User’s Manual
Cable(s)
I/O Back panel shield
iv
Chapter 1
Introduction of the Motherboard
1-1
Product Features
 Intel® LGA 1150 Socket Core i7/i5/i3/Pentium Processor
 Support 2 x DDR3 /DDR3L 1600/1333Mhz SO-DIMM up to 16GB
 2 x Intel® i211AT Gigabit Ethernet
 4 x USB3.0 (PCI-E to USB3.0), 8 x USB2.0
 2 x SATA Ports, 1 x PCI-Ex16 Slot
 1 x M-SATA (Co-lay Mini PCIe, Full size), 2 x Mini PCIe connector(Full size)
 12 x RS232 serial port (COM1/COM2 support RS232/422/485)
 2 x CRT Ports (CRT2 support Dummy load function)
 Support SIM Card Socket, TPM Header
 4 Phase CPU Power Support 84W CPU
 Integrated HD Audio CODEC with 6.0 CH
1
1-2 Specification
Spec
Description
®

Intel LGA 1150 Socket Core i7/i5/i3/Pentium Processor
LAN Chip








Audio Chip


2* DDR3L 1600/1333MHz SO-DIMM slot up to 16GB
2* Full-size Mini PCIe slot (MINI_CARD Co-lay MSATA)
1 * PCIex16 Slot
1* SIM Card socket
2* SATA III 6G/s Connector
1* Full-size mSATA (MINI_CARD Co-lay mini-PCIE)
®
2* Intel i211AT GbE
Support Fast Ethernet LAN function of providing 10/100/1000Mbps
Ethernet data transfer rate
Realtek ALC662 HD Audio Codec integrated
Audio driver and utility included
BIOS

AMI 32MB Flash ROM










1 * HDMI
2 * VGA
2* RS 232/422/485 serial ports (COM1/2)
2* RJ45, 10/100/1000 Mbps
4* USB3.0 & 2* USB2.0 ports
1* MIC, Line-in, Line-out port
1* Front panel header
1* PS/2 header
6* USB 2.0 header
10* RS 232 Serial port header
(COM3/COM4/COM5-COM8,COM9-COM12)
1 * dual RS 485 serial port header (DUAL_RS485)
1* parallel port header
1* TPM header
1* 8-bit GPIO (4* In and 4* Out)
1* SPEAK_CON amplifier header
1* LAN LED header
1* AT_ATX Mode header
1* CPU / Chassis Fan connectors
CPU
Memory
Expansion Slot
Storage
Rear I/O
Internal I/O








2
1-3 Main Board Diagram: Front
SATAIII Ports
(SATA1/2)
Top/Middle:
USB2.0
JW_FP
Header
Bottom:
HDMI
Mini-PCIE/
mSATA Slot
Top:
COM1
Mini-PCIe Slot
Bottom:
VGA1
ATXPWR
Connector
ATX12V
Connector
Top:
COM2
SYSFAN1 Header
Intel CPU
Socket
Bottom:
VGA2
Top:
RJ-45
LAN Port1
Middle/Bottom:
USB3.0 Ports
Top:
RJ-45
LAN Port2
SIM Card
Socket
LAN_LED
Header
SODIMM1
Middle/Bottom:
USB3.0 Ports
Top:
Line-In
Middle:
Line-Out
Bottom:
MIC
PCIe x16 Slot
SPEAK_CON
Header
3
CPUFAN Header
Main Board Diagram: Back
SODIMM2
4
Chapter 2
Hardware Installation
2-1 Location of Internal Jumper and Connector
SATAIII Ports
(SATA1/2)
COM5-COM8 DUAL_RS485 PS2_CON1
TPM1
COM4
COM3_SEL PS2_VCC
COM9-COM12
JPCOM3
PARALLEL
CASE_OPEN
Top/Middle:
USB2.0
Bottom:
HDMI
Top:
COM1
JW_FP
Header
COM3 JPCOM4
F_USB3
JBAT
F_USB2
F_USB1
COM4_SEL
BATCON
Mini-PCIE/
mSATA Slot
JPCOM1
Bottom:
VGA1
Mini PCIe
Connector
GPIO_CON
AT_ATX_MODE
ATXPWR
Connector
JP3
ATX12V
Connector
Top:
COM2
JPCOM2
JP4
SYSFAN1 Header
Intel CPU
Bottom:
VGA2
Top:
RJ-45
LAN Port2
Middle/Bottom:
USB3.0 Ports
Top:
RJ-45
LAN Port1
LAN_LED
Header
SIM Card
Socket
SODIMM1
Middle/Bottom:
USB3.0 Ports
Top:
Line-In
Middle:
Line-Out
Bottom:
MIC
SPEAK_CON
Header
PCIe x16
Connector
5
CPUFAN Header
2-2 Internal Jumper and Connector Setting
(1) JPCOM1/3/4 (4-pin): COM1/3/4 Port Pin9 Function Select
JPCOM3
JPCOM4
5 3 1
6 4 2
2-4 Closed:
RING (Default);
5 3 1
5 3 1
JPCOM1
6 4 2
6 4 2
3-4 Closed:
5V;
4-6 Closed:
12V.
JPCOM2
(2) JPCOM2 (4-pin): COM2 Port Pin9 Function Select
JPCOM3
JPCOM1
JPCOM2
JPCOM4
1
3
2
4
1
3
2
4
1
3
5
6
5
6
6
5
4-6 Closed:
12V.
2-4 Closed:
RING (Default);
6
3-4 Closed:
5V;
2
4
(3) COM3_SEL (4-pin): DUAL_RS485 COM3 RS232/RS485 Select
2 4
2 4
1 3
1-2 Closed:
RS232 (Default);
1 3
COM3_SEL
3-4 Closed:
RS485.
(4) COM4_SEL (4-pin): DUAL_RS485 COM4 RS232/RS485 Select
COM4_SEL
3 1
3 1
4 2
1-2 Closed:
RS232 (Default);
3-4 Closed:
RS485.
4 2
(5) PS2_VCC (3-pin): PS2_CON1 VCC 5V/5VSB Select
PS2_VCC
1
3
1-2 Close:
5V (Default);
1
3
2-3 Close:
5VSB.
(6) JBAT (3-pin): Clear CMOS Setting
JBAT
1
3
1-2 Close:
5V (Default);
7
1
3
2-3 Close:
5VSB.
(7) AT_ATX_MODE (3-pin): AT_ATX_MODE Select
1
3
1-2 Close:
5V (Default);
1
3
2-3 Close:
5VSB.
AT_ATX_MODE
*ATX Mode Selected: Press power button to power on after power input ready;
AT Mode Selected: Directly power on as power input ready.
(8) CASE_OPEN (2-pin): Case Open Message Display Function Select
CASE_OPEN
1
1
1-2 Open:
1-2 Closed:
Normal (Default);
Case Open.
Pin (1-2) Close: When Case Open function pin short to GND, the Case Open function
was detected. When Used, needs to enter BIOS and enable ‘Case Open Detect’
function. In this case if your case is removed, next time when you restart your computer,
a message will be displayed on screen to inform you of this.
8
JP3 (6-pin) &JP4 (6-pin): MINI_CARD Slot Mini-PCIE/MSATA Function Select
JP3&JP4→ MINI_CARD Function Select
2 4 6
2 4 6
JP3→
← JP4
1 3 5
1 3 5
(1-3) & (2-4) Closed: MINI_CARD
functions as MSATA interface.
2 4 6
2 4 6
JP3→
←JP4
1 3 5
JP3
1 3 5
(3-5) & (4-6) Closed: MINI_CARD
functions as Mini-PCIE Slot.
JP4
2-2-1 Connectors
(1) Rear I/O Connectors
USB2.0 Port
HDMI
COM1
COM2
VGA1
VGA2
9
RJ-45
RJ-45
LAN2 Port LAN1 Port
USB 3.0 Port
Blue:Line-IN
Green:Line-OUT
Pink:MIC
Icon
Name
Function
USB 2.0 Port
To connect USB keyboard, mouse or other
devices compatible with USB specification.
HDMI Port
To connect display device that support HDMI
specification.
RS232/422/485
COM Port
Mainly for user to connect external MODEM
or other devices that supports
Serial Communications Interface.
VGA Port
To connect display device that support VGA
specification.
RJ-45 LAN Port
This connector is standard RJ-45 LAN jack
for Network connection.
To connect USB keyboard, mouse or other
devices compatible with USB specification.
USB 3.0 ports supports up to 5Gbps data
transfer rate.
USB 3.0 Port
BLUE : Line-in Connector
GREEN : Line-out Connector
PINK : MIC Connector
Audio Connectors
10
COM1/COM2 (9-pin Block): RS232/422/485 Serial Port
RS422 RX(B)
RS422 RX(A)
RS422 TX(A)
RS422 TX(B)
RS485 D+(A)
RS485 D-(B)
For RS422 Mode
For RS485 Mode
COM1/COM2 port can function as RS232/422/485 serial port. In normal settings
COM1/2 functions as RS232 port. With compatible COM cable COM1/2 can function as
RS422 or RS 485 port.
User also needs to go to BIOS to set ‘Transmission Mode Select’ for COM1/ COM2
(refer to Page 26) at first, before using specialized cable to connect different pins of this
port.
ATXPWR (24-pin block): Main Power Connector
ATX Power
Connector
11
ATX12V (4-pin block): ATX12V Type Power Connector
Pin1
Pin No.
ATX12V
Definition
1
GND
2
GND
3
+12V
4
+12V
SATA1/2 (7-pin Block): SATAIII Port connector
The board comes with SATA1 & SATA2 port that supports 6GB/s transfer rate.
SATA2
SATA1
Pin No.
Definition
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
SYSFAN1 (3-pin): System Fan Header
Pin1
GND
+12V Fan Power
Fan Clock
SYSFAN1
12
CPUFAN (4-pin): CPUFAN Header
Control
Fan Speed
+12V Fan Power
GND
CPUFAN
Pin1
2-2-2 Headers
(1) JW_FP (9-pin): Front Panel Header
GND
PWRBTN
PWRLEDPWRLED+
JW_FP
PIN 1
VCC
RSTSW
GND
HDDLEDHDDLED+
(2) PS2_CON1 (6-pin): PS/2 Keyboard & Mouse Header
PS2_CON1
MS_CLK
VCC
MS_DATA
KB_DATA
GND
KB_CLK
Pin1
13
(3) LAN_LED (8-pin): LANLED Header
3VSB
3VSB
LAN1_100-
LAN2_100-
LAN_LED
Pin1
5
LAN1_ACT-
LAN1_1G-
LAN2_ACT-
LAN2_1G-
(4) SPEAK_CON (4-pin): 3W Amplifier Header
Pin1
Pin No.
Definition
1
L-
2
L+
3
R+
4
R-
SPEAK_CON
(5) F_USB1/2/3 (9-pin): USB 2.0 Port Header
NC
GND
+DATA
-DATA
VCC
FP_USB1
Pin 1
GND
+DATA
-DATA
VCC
FP_USB2
FP_USB3
14
(6) TPM1 (20-pin): TPM Header
GPIO69
SERIRO
NC
GND
LAD1
LAD2
VCC
(8) GPIO_CON (10-pin): 8-bit GPIO Header
GPIO_84
GPIO_ 86
GN D
GPIO_87
VCC
GPIO_85
GPIO_ 82
GPIO_ 80
2
GPIO_83
GPIO_81
Pin 1
LPC_PDGND
3VSB
GPIO68
LAD0
LAD3
VCC3
15
PLTRSTLFRAME-
P_SLCT
P_PE
P_BUSY
P_ACKP_PRD7
P_PRD6
P_PRD5
P_PRD4
P_PRD3
P_PRD2
P_PRD1
P_PRD0
P_STB-
GPIO_CON
NC
GND
GND
GND
GND
GND
GND
GND
GND
P_SLINP_INITP_ERRP_AFD-
PARALLEL
PCLK_TPM
Pin 1
NC
GND
TPM1
20
2
19
(7) PARALLEL (25-pin): Parallel Port Header
14
Pin 1
13
(9) COM3/4 (9-Pin): RS232 Serial Port Header
COM3
COM4
RI
CTS
RTS
DSR
Pin6
Pin1
GND
DTR
TXD
RXD
DCD
(10)
DUAL_RS485 (4-pin): RS485 Header
TD4TD3-
DUAL_RS485
2
Pin1
TD4+
TD3+
DUAL_RS485 header serves as COM3/4 header RS485 function expansion block. For
RS485 function, user needs to go to BIOS→‘Serial Port 3 Configuration’/‘Serial Port
4 Configuration’ to set ‘Device Mode’ as [RS485], also go to set Jumper COM3_SEL
or COM4_SEL as [RS485] mode before connecting compatible cable to corresponding
Pin1-2 (COM3 RS485) or Pin 3-4 (COM4 RS485).
16
(11)
COM3-COM6/ COM7-COM10 (40-Pin): RS232 Serial Port Header Block
COM5-COM8
COM5-COM8
COM9-COM12
COM8
COM6
COM9-COM12
RS232
Pin NO.
RS232
Pin NO.
RS232
Pin NO.
RS232
DCD5
Pin 2
DSR5
Pin 1
DCD9
Pin 2
DSR9
Pin3
SIN5
Pin 4
RTS5
Pin3
SIN9
Pin 4
RTS9
Pin 5
SOUT5
Pin 6
CTS5
Pin 5
SOUT9
Pin 6
CTS9
RI5
Pin 7
DTR9
Pin 8
RI9
NC
Pin 9
GND
Pin 10
NC
DSR6
Pin 11
DCD10
Pin 12
DSR10
RTS6
Pin 13
SIN10
Pin 14
RTS10
Pin 15
SOUT10
Pin 16
CTS10
Pin 11
Pin 13
DTR5
GND
DCD6
SIN6
Pin 8
Pin 10
Pin 12
Pin 14
COM9
COM10
Pin 15
SOUT6
Pin 16
CTS6
Pin 17
DTR6
Pin 18
RI6
Pin 17
DTR10
Pin 18
RI10
Pin 19
GND
Pin 20
NC
Pin 19
GND
Pin 20
NC
Pin 21
DCD7
Pin 22
DSR7
Pin 21
DCD11
Pin 22
DSR11
Pin 23
SIN7
Pin 24
RTS7
Pin 23
SIN11
Pin 24
RTS11
Pin 25
SOUT11
Pin 26
CTS11
RI7
Pin 27
DTR11
Pin 28
RI11
GND
Pin 30
NC
Pin 25
Pin 27
COM8
COM11
COM9
Pin 1
Pin 9
COM7
Pin 40
Pin 39
Pin NO.
Pin 7
COM6
COM12
Pin 2
Pin 1
COM7
COM5
COM5
COM10
Pin 40
Pin 39
Pin 2
Pin 1
COM5-COM8
COM9-COM12
SOUT7
DTR7
Pin 26
Pin 28
COM11
CTS7
Pin 29
GND
Pin 30
NC
Pin 29
Pin 31
DCD8
Pin 32
DSR80
Pin 31
DCD12
Pin 32
DSR12
Pin 33
SIN8
Pin 34
RTS8
Pin 33
SIN12
Pin 34
RTS12
Pin 35
SOUT8
Pin 36
CTS8
Pin 35
SOUT12
Pin 36
CTS12
Pin 37
DTR8
Pin 38
RI8
Pin 37
DTR12
Pin 38
RI12
NC
Pin 39
GND
Pin 40
NC
Pin 39
GND
Pin 40
COM12
17
Chapter 3
Introducing BIOS
Notice!
The BIOS options in this manual are for reference only. Different
configurations may lead to difference in BIOS screen and BIOS screens
in manuals are usually the first BIOS version when the board is released
and may be different from your purchased motherboard. Users are
welcome to download the latest BIOS version form our official website.
The BIOS is a program located on a Flash Memory on the motherboard. This program
is a bridge between motherboard and operating system. When you start the computer,
the BIOS program will gain control. The BIOS first operates an auto-diagnostic test called
POST (power on self test) for all the necessary hardware, it detects the entire hardware
device and configures the parameters of the hardware synchronization. Only when
these tasks are completed done it gives up control of the computer to operating system
(OS). Since the BIOS is the only channel for hardware and software to communicate, it
is the key factor for system stability, and in ensuring that your system performance as
its best.
3-1
Entering Setup
Power on the computer and by pressing <Del> immediately allows you to enter Setup.
If the message disappears before your respond and you still wish to enter Setup,
restart the system to try again by turning it OFF then ON or pressing the “RESET”
button on the system case. You may also restart by simultaneously pressing <Ctrl>,
<Alt> and <Delete> keys. If you do not press the keys at the correct time and the
system does not boot, an error message will be displayed and you will again be asked
to
<Del> to enter Setup
Press
3-2
BIOS Menu Screen
18
The following diagram show a general BIOS menu screen:
BIOS Menu Screen
Menu Bar
General Help Items
Current Setting Value
Menu Items
3-3
Function Keys
Function Keys
In the above BIOS Setup main menu of, you can see several options. We will explain
these options step by step in the following pages of this chapter, but let us first see a
short description of the function keys you may use here:
 Press (left, right) to select screen;
 Press  (up, down) to choose, in the main menu, the option you want to confirm or
to modify.
 Press <Enter> to select.
 Press <+>/<–> keys when you want to modify the BIOS parameters for the active
option.
 [F1]: General help.
 [F2]: Previous values.
 [F3]: Optimized defaults.
 [F4]: Save & Exit.
 [F10]: Save & Reset.
19

Press <Esc> to quit the BIOS Setup.
3-4
Getting Help
Main Menu
The on-line description of the highlighted setup function is displayed at the top right
corner the screen.
Status Page Setup Menu/Option Page Setup Menu
Press [F1] to pop up a small help window that describes the appropriate keys to use
and the possible selections for the highlighted item. To exit the Help Window, press
<Esc>.
3-5 Menu Bars
There are six menu bars on top of BIOS screen:
Main
To change system basic configuration
Advanced
To change system advanced configuration
Chipset
To change chipset configuration
Security
Password settings
Boot
To change boot settings
Save & Exit
Save setting, loading and exit options.
User can press the right or left arrow key on the keyboard to switch from menu bar. The
selected one is highlighted.
3-6
Main Menu
Main menu screen includes some basic system information. Highlight the item and then
use the <+> or <-> and numerical keyboard keys to select the value you want in each
item.
20
System Date
Set the date. Please use [Tab] to switch between date elements.
System Time
Set the time. Please use [Tab] to switch between time elements.
3-7 Advanced Menu
 ACPI Settings
Press [Enter] to make settings for the following sub-item:
21
Enable Hibernation
Use this item to select system ability to Hibernate (OS/S4 Sleet State).
The optional settings are: [Disabled]; [Enabled].
ACPI Sleep State
Use this item to select ACPI sleep state the system will enter when the suspend
button is pressed.
The optional settings are: [Suspend Disabled]; [S1 only (CPU Stop Clock)]; [S3 only
(Suspend to RAM)].
ERP Support
Use this item to disable or enable ERP to active all wake-up functions.
The optional settings are: [Disabled]; [Enabled].
Wake-Up by PCIE/Lan
Use this item to disable or enable PCIE Device PME in S1/S3/S4/S5.
The optional settings are: [Disabled]; [Enabled].
Wake-Up by Ring
Use this item to disable or enable Wake-Up by Ring.
The optional settings are: [Disabled]; [Enabled].
Wake-Up by PS/2 keyboard
Use this item to disable or enable PS/2 keyboard Wake-up from S3/S4/S5.
The optional settings are: [Disabled]; [Enabled].
Wake-Up by PS/2 mouse
Use this item to disable or enable PS/2 mouse Wake-up from S3/S4/S5.
The optional settings are: [Disabled]; [Enabled].
PWRON After PWR-Fail
Use this item to select the power supply status.
The optional settings are: [Former-Sts]; [Always On]; [Always Off].
[Former-Sts]: Remain the status when power is restored.
[Always On]: Device will automatically start up when power is restored.
[Always Off]: Device will remain powered off even when power is restored.
USB StandBy Power Support`
Use this item to disable or enable USB2 StandBy Power.
The optional settings are: [Disabled]; [Enabled].
 Trusted Computing
22
Press [Enter] to make settings for the following sub-item:
Security Device Support
Use this item to enable or disable BIOS support for security device. OS will not
show Security Device. TCG EFI protocol and INT1A interface will not be available.
The optional settings: [Disabled]; [Enabled].
 RTC WakeUp Settings
Press [Enter] to make settings for the following sub-item:
Wake system with Fixed Time
Use this item to enable or disable system wake-up on alarm event.
The optional settings: [Disabled]; [Enabled].
When set as [Enabled], system will wake on the Hour/Minute/Second specified.
Wake system with Dynamic Time
Use this item to enable or disable system wake-up on alarm event.
The optional settings: [Disabled]; [Enabled].
When set as [Enabled], system will wake on the (Current time) + (Increased
minute(s)).
Wake up minute increase
The range is from [1] to [60] minutes.
 SATA Configuration
Press [Enter] to make settings for the following sub-items:
SATA Controller(s)
The optional settings are: [Enabled]; [Disabled].
When user set it as [Enabled], the following items will show up for user to make
further settings:
SATA Mode Selection
The optional settings are: [IDE]; [AHCI].
When user set it as [AHCI], the following items will show up for user to make
further settings:
SATA Controller Speed
The item is for user to set the maximum speed the SATA controller can
support.
The optional settings are: [Default]; [Gen1]; [Gen2]; [Gen3].
SATA1
23
Port Support
The optional settings are: [Disabled]; [Enabled].
Hot Plug
The optional settings are: [Disabled]; [Enabled].
SATA Device Type
The optional settings are: [Hard Disk Drive]; [Solid State Drive].
SATA2
Port Support
The optional settings are: [Disabled]; [Enabled].
Hot Plug
The optional settings are: [Disabled]; [Enabled].
SATA Device Type
The optional settings are: [Hard Disk Drive]; [Solid State Drive].
MSATA
Port Support
The optional settings are: [Disabled]; [Enabled].
SATA Device Type
The optional settings are: [Hard Disk Drive]; [Solid State Drive].
►
PCH-FW Configuration
Press [Enter] to see Management Engine Technology Parameters information.
Me FW Image Re-Flash
Use this item to enable or disable Me FW Image Re-Flash function.
The optional settings are: [Disabled]; [Enabled].
 USB Configuration
Press [Enter] to make settings for the following sub-items:
Legacy USB Support
The optional settings are: [Enabled]; [Disabled]; [Auto].
[Enabled]: To enable legacy USB support.
[Disabled]: To keep USB devices available only for EFI specification,
[Auto]: To disable legacy support if no USB devices are connected.
XHCI Hand-off
This is a workaround for OSes without XHCI hand-off support. The XHCI ownership
change should be claimed by XHCI driver.
24
The optional settings are: [Enabled]; [Disabled].
EHCI Hand-off
This is a workaround for OSes without EHCI hand-off support. The EHCI ownership
change should be claimed by EHCI driver.
The optional settings are: [Disabled]; [Enabled].
USB Mass Storage Driver Support
The optional settings are: [Disabled]; [Enabled].
USB Transfer Time-out
Use this item to set the time-out value for control, bulk, and interrupt transfers.
The optional settings are: [1 sec]; [5 sec]; [10 sec]; [20 sec].
Device Reset time-out
Use this item to set USB mass storage device start unit command time-out.
The optional settings are: [10 sec]; [20 sec]; [30 sec]; [40 sec].
Device Power-up Delay
Use this item to set maximum time the device will take before it properly reports
itself to the host controller. ‘Auto’ uses default value: for a root port it is 100 ms, for a
hub port the delay is taken from hub descriptor.
The optional settings: [Auto]; [Manual].
Select [Manual] you can set value for the following sub-item: ‘Device Power-up
Delay in Seconds’.
Device Power-up Delay in Seconds
The delay range is from [1] to [40] seconds, in one second increments.
►
Super I/O Configuration
Press [Enter] to make settings for the following sub-items:
►
Serial Port 1 Configuration
Press [Enter] to make settings for the following items:
Serial Port
Use this item to enable or disable serial port (COM).
The optional settings are: [Disabled]; [Enabled].
Change Settings
Use this item to select an optimal setting for super IO device.
The optional settings are: [Auto]; [IO=3F8h; IRQ=4;];
IRQ=3,4,5,6,7,10,11;];
[IO=2F8h;
IRQ=3,4,5,6,7,10,11;];
25
[IO=3F8h;
[IO=3E8h;
IRQ=3,4,5,6,7,10,11;] ; [IO=2E8h; IRQ=3,4,5,6,7,10,11;].
Transmission Mode Select
Use this item to select transmission mode.
The optional settings are: [RS422]; [RS232]; [RS485].
Mode Speed Select
Use this item to select RS232/RS422/RS485 speed.
The optional settings are: [RS232=1Mbps, RS422/RS485=10Mbps];
[RS232/RS422/RS485=250Kbps].
►
Serial Port 2 Configuration
Press [Enter] to make settings for the following items:
Serial Port
Use this item to enable or disable serial port (COM).
The optional settings are: [Disabled]; [Enabled].
Change Settings
Use this item to select an optimal setting for super IO device.
The optional settings are: [Auto]; [IO=2F8h; IRQ=3;]; [IO=3F8h;
IRQ=3,4,5,6,7,10,11;];
[IO=2F8h;
IRQ=3,4,5,6,7,10,11;];
[IO=3E8h;
IRQ=3,4,5,6,7,10,11;]; [IO=2E8h; IRQ=3,4,5,6,7,10,11;].
Transmission Mode Select
Use this item to select transmission mode.
The optional settings are: [RS422]; [RS232]; [RS485].
Mode Speed Select
Use this item to select RS232/RS422/RS485 speed.
The optional settings are: [RS232=1Mbps, RS422/RS485=10Mbps];
[RS232/RS422/RS485=250Kbps].
►
Serial Port 3 Configuration
Press [Enter] to make settings for the following items:
Serial Port
Use this item to enable or disable serial port (COM).
The optional settings are: [Disabled]; [Enabled].
Change Settings
Use this item to select an optimal setting for super IO device.
The optional settings are: [Auto]; [IO=3E8h; IRQ=6;];
26
[IO=3E8h;
IRQ=3,4,5,6,7,10,11;];
[IO=2E8h;
IRQ=3,4,5,6,7,10,11;];
IRQ=3,4,5,6,7,10,11;]; [IO=2E0h; IRQ=3,4,5,6,7,10,11;].
Device Mode
Use this item to select <High Speed> or <Normal mode> mode.
The optional settings are: [RS232]; [RS485].
►
►
►
Serial Port 4 Configuration
Press [Enter] to make settings for the following items:
Serial Port
Use this item to enable or disable serial port (COM).
The optional settings are: [Disabled]; [Enabled].
Change Settings
Use this item to select an optimal setting for super IO device.
The optional settings are: [Auto]; [IO=2E8h; IRQ=6;];
IRQ=3,4,5,6,7,10,11;];
[IO=2E8h;
IRQ=3,4,5,6,7,10,11;];
IRQ=3,4,5,6,7,10,11;]; [IO=2E0h; IRQ=3,4,5,6,7,10,11;].
Device Mode
Use this item to select <High Speed> or <Normal mode> mode.
The optional settings are: [RS232]; [RS485].
Serial Port 5 Configuration
Press [Enter] to make settings for the following items:
Serial Port
Use this item to enable or disable serial port (COM).
The optional settings are: [Disabled]; [Enabled].
Change Settings
Use this item to select an optimal setting for super IO device.
The optional settings are: [Auto]; [IO=2F0h; IRQ=6;];
IRQ=3,4,5,6,7,10,11;];
[IO=2E8h;
IRQ=3,4,5,6,7,10,11;];
IRQ=3,4,5,6,7,10,11;]; [IO=2E0h; IRQ=3,4,5,6,7,10,11;].
Serial Port 6 Configuration
Press [Enter] to make settings for the following items:
Serial Port
Use this item to enable or disable serial port (COM).
27
[IO=2F0h;
[IO=3E8h;
[IO=2F0h;
[IO=3E8h;
[IO=2F0h;
The optional settings are: [Disabled]; [Enabled].
Change Settings
Use this item to select an optimal setting for super IO device.
The optional settings are: [Auto]; [IO=2E0h; IRQ=6;]; [IO=3E8h;
IRQ=3,4,5,6,7,10,11;];
[IO=2E8h;
IRQ=3,4,5,6,7,10,11;];
[IO=2F0h;
IRQ=3,4,5,6,7,10,11;]; [IO=2E0h; IRQ=3,4,5,6,7,10,11;].
WatchDog Timer
The optional settings are: [Disabled]; [Enabled].
When user set it as [Enabled], the following items will show up for user to make
further settings:
WatchDog Timer Value: The temperature range is from [1] to [255].
WatchDog Timer Unit: The optional settings are [Sec.]; [Min.].
Case Open Detect
Use this item to detect case has already open or not, and show message in POST.
The optional settings are: [Disabled]; [Enabled].
 F81866 H/W Monitor
Press [Enter] to make settings for the following sub-item:
Shutdown Temperature Configuration
Use this item to select system shutdown temperature.
The optional settings are: [Disabled]; [60C/140F]; [65C/149F]; [70C/158F];
[75C/167F];
CPUFAN Smart Mode
The optional settings are: [Disabled]; [Enabled].
Select [Enabled] you can set value for the following sub-item:
CPUFAN Highest speed Temp
The temperature range is from [Min>=Idel Temp.] to [Max=100C].
CPUFAN Idle Temp
The idel speed temperature range is from [Min=0C.] to [Max<=Full-speed Temp].
►
Second Super I/O Configuration
Press [Enter] to make settings for the following sub-items:
►
Serial Port 7 Configuration
28
Press [Enter] to make settings for the following items:
Serial Port
Use this item to enable or disable serial port (COM).
The optional settings are: [Disabled]; [Enabled].
Change Settings
Use this item to select an optimal setting for super IO device.
The optional settings are: [Auto]; [IO=240h; IRQ=5;];
IRQ=3,4,5,6,7,10,11;];
[IO=248h;
IRQ=3,4,5,6,7,10,11;];
IRQ=3,4,5,6,7,10,11;] ; [IO=258h; IRQ=3,4,5,6,7,10,11;].
►
►
►
Serial Port 8 Configuration
Press [Enter] to make settings for the following items:
Serial Port
Use this item to enable or disable serial port (COM).
The optional settings are: [Disabled]; [Enabled].
Change Settings
Use this item to select an optimal setting for super IO device.
The optional settings are: [Auto]; [IO=248h; IRQ=5;];
IRQ=3,4,5,6,7,10,11;];
[IO=248h;
IRQ=3,4,5,6,7,10,11;];
IRQ=3,4,5,6,7,10,11;]; [IO=258h; IRQ=3,4,5,6,7,10,11;].
Serial Port 9 Configuration
Press [Enter] to make settings for the following items:
Serial Port
Use this item to enable or disable serial port (COM).
The optional settings are: [Disabled]; [Enabled].
Change Settings
Use this item to select an optimal setting for super IO device.
The optional settings are: [Auto]; [IO=250h; IRQ=5;];
IRQ=3,4,5,6,7,10,11;];
[IO=258h;
IRQ=3,4,5,6,7,10,11;];
IRQ=3,4,5,6,7,10,11;]; [IO=268h; IRQ=3,4,5,6,7,10,11;].
Serial Port 10 Configuration
Press [Enter] to make settings for the following items:
Serial Port
29
[IO=240h;
[IO=250h;
[IO=240h;
[IO=250h;
[IO=250h;
[IO=260h;
Use this item to enable or disable serial port (COM).
The optional settings are: [Disabled]; [Enabled].
Change Settings
Use this item to select an optimal setting for super IO device.
The optional settings are: [Auto]; [IO=258h; IRQ=5;];
IRQ=3,4,5,6,7,10,11;];
[IO=258h;
IRQ=3,4,5,6,7,10,11;];
IRQ=3,4,5,6,7,10,11;]; [IO=268h; IRQ=3,4,5,6,7,10,11;].
►
►
►
Serial Port 11 Configuration
Press [Enter] to make settings for the following items:
Serial Port
Use this item to enable or disable serial port (COM).
The optional settings are: [Disabled]; [Enabled].
Change Settings
Use this item to select an optimal setting for super IO device.
The optional settings are: [Auto]; [IO=260h; IRQ=5;];
IRQ=3,4,5,6,7,10,11;];
[IO=258h;
IRQ=3,4,5,6,7,10,11;];
IRQ=3,4,5,6,7,10,11;]; [IO=268h; IRQ=3,4,5,6,7,10,11;].
Serial Port 12 Configuration
Press [Enter] to make settings for the following items:
Serial Port
Use this item to enable or disable serial port (COM).
The optional settings are: [Disabled]; [Enabled].
Change Settings
Use this item to select an optimal setting for super IO device.
The optional settings are: [Auto]; [IO=268h; IRQ=5;];
IRQ=3,4,5,6,7,10,11;];
[IO=258h;
IRQ=3,4,5,6,7,10,11;];
IRQ=3,4,5,6,7,10,11;]; [IO=268h; IRQ=3,4,5,6,7,10,11;].
Parallel Port Configuration
Press [Enter] to make settings for the following items:
Parallel Port
Use this item to enable or disable Parallel port (LPT/LPTE).
The optional settings are: [Disabled]; [Enabled].
30
[IO=250h;
[IO=260h;
[IO=250h;
[IO=260h;
[IO=250h;
[IO=260h;
Change Settings
Use this item to select an optimal setting for super IO device.
The optional settings are: [Auto]; [IO=378h; IRQ=7;]; [IO=378h; IRQ=7,10,11,12;];
[IO=278h; IRQ=7,10,11,12;]; [IO=38Ch; IRQ=7,10,11,12;].
Device Mode
Use this item to select Printer Port mode.
The optional settings are: [STD Printer Mode]; [SPP Mode]; [EPP-1.9 and SPP
Mode]; [EPP-1.7 and SPP Mode]; [ECP Mode]; [ECP and EPP 1.9 Mode]; [ECP
and EPP 1.7 Mode].
3-8 Chipset Menu
 PCH-IO Configuration
 USB Configuration
Press [Enter] to view current using memory information and make settings for the
following sub-items:
USB Precondition
Use this item to enable or disable precondition work on USB host controller and root
ports for faster enumeration.
The optional settings are: [Disabled]; [Enabled].
XHCI Mode
31
Use this item to selectmode of operation of XHCI controller.
The optional settings are: [Smart Auto]; [Auto]; [Enabled]; [Disabled]; [Manual].
When user set it as [Disabled], the following items will show up for user to make
further settings:
EHCI1: Use this item to control the USB EHCI (USB 2.0) functions. One EHCI
controller must always be enabled.
The optional settings are [Disabled]; [Enabled].
EHCI2: Use this item to control the USB EHCI (USB 2.0) functions. One EHCI
controller must always be enabled.
The optional settings are [Disabled]; [Enabled].
Select [Manual] you can set value for the following sub-item:
XHCI Pre-Boot Driver
The optional settings are: [Enabled]; [Disabled].
Route USB 2.0 pins to which HC?
The optional settings are: [Route Per-Pin]; [Route all Pins to EHCI]; [Route all
Pins to XHCI].
When user set it as [Route Per-Pin], the following items will show up for user to
make further settings:
USB 2.0 PIN #0 / #1 / #2 / #3 / #4 / #5 / #6 / #7 / #8 / #9 / #10 / #11 / #12 / #13:
The optional settings are [Route to EXCI]; [Route to XHCI].
Enable USB 3.0 pins
The optional settings are: [Select Per-Pin]; [Disabled all Pins]; [Enable all Pins].
When user set it as [Select Per-Pin], the following items will show up for user to
make further settings:
USB 3.0 PIN #1 / #2 / #3 / #4 / #5 / #6: The optional settings are [Disabled];
[Enabled].
USB Ports Per-Port Disable Control
The optional settings are: [Disabled]; [Enabled].
Select [Enabled] you can set value for the following sub-item:
USB Port 1/2/3/4/5/6/9/10/11/12 and USB30 Port 1/2
The optional settings are: [Disabled]; [Enabled].
PCIE2USB3.0 Support
Use this item to enable or disable PCI Express Root Port.
The optional settings are: [Disabled]; [Enabled].
32
Onboard PCIE Lan1
Use this item to enable or disable PCI Express Root Port.
The optional settings are: [Disabled]; [Enabled].
Onboard PCIE Lan2
The optional settings are: [Disabled]; [Enabled].
MINIPCIE
The optional settings are: [Disabled]; [Enabled].
MINI_CARD
Use this item to enable or disable PCI Express Root Port. Only Valid if Pin2&3
Closed of JP3 & JP4 & JP5 & JP6.
The optional settings are: [Disabled]; [Enabled].
Onboard Lan BootROM
Use this item to enable or disable Boot Option ROM for Onboard Network Devices.
The optional settings are: [Disabled]; [Enabled].
Azalia
Use this item to select detection of the Azalia device.
The optional settings are: [Disabled]; [Enabled].
Azalia Internal HDMI Codec
Use this item to enable or disable internal HDMI codec for Azalia.
The optional settings are: [Enabled]; [Disabled].
► System Agent (SA) Configuration
Press [Enter] to make settings for the following sub-items:
VT-d
Use this item to enable or disable VT-d function on MCH.
The optional settings are: [Disabled]; [Enabled].
VGA1 Dummy Load
Use this item to enable or disable VGA Dummy Load.
The optional settings are: [Disabled]; [Enabled].
VGA2 Dummy Load
The optional settings are: [Disabled]; [Enabled].
Primary Display
Use this item to select which of IGFX/PEG/PCI Graphics device should be Primary
Display or select SG for Switchable Gfx..
The optional settings are: [Auto]; [IGFX]; [PEG].
33
Internal Graphics
The optional settings are: [Auto]; [Disabled]; [Enabled].
[Auto]: Auto Disable Internal Graphics if detect PCIE VGA card.
[Disabled]: Always Disable Internal Graphics.
[Enabled]: Always Enable Internal Graphics.
Aperture Size
The optional settings are: [128MB]; [256MB]; [512MB].
DVMT Pre-Allocated
Use this item to select DVMT 5.0 pre-allocated (Fixed) Graphics Memory size used
by the Internal Graphics Device.
The optional settings are: [32M]; [64M]; [96M]; [128M]; [160M]; [192M]; [224M];
[256M]; [288M]; [320M]; [352M]; [384M]; [416M]; [448M]; [480M]; [512M]; [1024M].
DVMT Total Gfx Mem
Use this item to select DVMT 5.0 Total Graphics Memory size used by the Internal
Graphics Device.
The optional settings are: [128M]; [256M]; [MAX].
RC6 (Render Standby)
The optional settings are: [Disabled]; [Enabled].
Enable PEG
The optional settings are: [Disabled]; [Enabled]; [Auto].
Select [Enabled] and [Auto] you can set value for the following sub-item:
PEG – Gen X
Use this item to configure PEG B0:D1:F0 Gen1-Gen3.
The optional settings are: [Auto]; [Gen1]; [Gen2]; [Gen3].
Detect Non-Compliance Device
The optional settings are: [Disabled]; [Enabled].
PEG – ASPM
Use this item to select ASPM support for the PEG Device. This has no effect if PEG
is not the currently active device.
The optional settings are: [Disabled]; [Auto]; [ASPM L0s]; [ASPM L1]; [ASPM
L0sL1].
Select [ASPM L0s] and [ASPM L0sL1] you can set value for the following sub-item:
ASPM L0s
Use this item to enable PCIe ASPM L0s.
34
The optional settings are: [Root Port Only]; [Endpoint Port Only]; [Both Root
and Endpoint Ports].
VGA2 Support
The optional settings are: [Disabled]; [Enabled].
3-9 Boot Menu
Boot Configuration
► Setup Prompt Timeout
Use this item to set number of seconds to wait for setup activation key.
► Bootup Numlock State
Use this item to select keyboard NumLock state.
The optional settings are: [On]; [Off].
► Fast Boot
The optional settings are: [Disabled]; [Enabled].
When user set it as [Enabled], the following items will show up for user to make further
settings:
SATA Support
The optional settings are: [Last Boot HDD Only]; [All Sata Devices]; [HDD Only].
35
VGA Support
When user set it as [Auto], only install Legacy OpRom with Legacy OS and logo
would NOT be shown during post. Efi driver will still be installed with EFI OS.
The optional settings are: [Auto]; [EFI Driver].
USB Support
The optional settings are: [Disabled]; [Full Initial]; [Partial Initial].
[Disabled]: All USB devices will not be available until after OS boot.
[Full Initial]: USB Mass storage and specific USB port/device will NOT be available
before OS boot.
[Partial Initial]: All USB devices will be available in OS and Post.
PS2 Devices Support
The optional settings are: [Disabled]; [Enabled].
NetWork Stack Driver Support
The optional settings are: [Disabled]; [Enabled].
Boot Option Priorities
► CSM parameters
Use this item to control CSM launched.
Launch CSM
The optional settings are: [Enabled]; [Disabled].
Boot option filter
The optional settings are: [UEFI and Legacy]; [Legacy only]; [UEFI only].
Launch Storage OpROM policy
The optional settings are: [Do not launch]; [UEFI only]; [Legacy only].
Launch Video OpROM policy
The optional settings are: [Do not launch]; [UEFI only]; [Legacy only]; [Legacy first];
[UEFI first].
Other PCI device ROM priority
The optional settings are: [UEFI OpROM]; [Legacy OpROM].
36
3-10 Security Menu
Security menu allow users to change administrator password and user password
settings.
3-11TurboOC Menu
37
 CPU Configuration
Press [Enter] to view current CPU configuration and make settings for the following
sub-items:
Active Processor cores
Use this item to select number of cores to enable in each processor package.
The optional settings: [All]; [1]; [2]; [3].
Limit CPUID Maximum
The optional settings are: [Disabled]; [Enabled].
This item should be set as [Disabled] for Windows XP.
Execute Disable Bit
The optional settings: [Disabled]; [Enabled].
Intel Virtualization Technology
The optional settings: [Disabled]; [Enabled].
When set as [Enabled], a VMM can utilize the additional hardware capabilities
provided by Vanderpool Technology.
EIST
Use this item to enable or disable Intel SpeedStep.
The optional settings: [Disabled]; [Enabled].
When set as [Enabled], the following items will show up for user to make further
settings:
Turbo Mode
The optional settings: [Disabled]; [Enabled].
Turbo Core Ratio Limit
Use this item to setup Turbo Core Ratio. [0] means using the factory-configured
value.
CPU C State
Use this item to enable or disable CPU C state.
The optional settings: [Disabled]; [Enabled].
When set as [Enabled], user can see Enhanced C1 state:
Enhanced C1 state
Use this item to enable or disable CPU C1 state.
The optional settings: [Disabled]; [Enabled].
CPU C3 Report
The optional settings: [Disabled]; [Enabled].
38
CPU C6 Report
The optional settings: [Disabled]; [Enabled].
C6 Latency
The optional settings: [Short]; [Long].
CPU C7 Report
The optional settings: [Disabled]; [CPU C7]; [CPU C7s].
C7 Latency
The optional settings: [Short]; [Long].
► Memory Configuration
Press [Enter] to make settings for the following sub-items:
DIMM profile
Use this item to select DIMM timing profile that should be used.
The optional settings are: [Default DIMM profile]; [Custom Profile].
When set as [Custom Profile], the sub-item ‘Custom Profile Control’ will appear
for user to manually set memory timing configuration.
Memory Frequency Limiter
Use this item to set maximum memory frequency selection in Mhz. This item will not
show on the screen when ‘DIMM Profile’ is set as: [Custom Profile].
The optional settings are [1066]; [1333]; [1600].
tCL
The Cas Latency Range is from [4] to [18].
tRCD
The Row to Col Delay Range is from [1] to [38].
tRP
The Ras Precharge Range is from [1] to [38].
tRAS
The Ras Active Time Range is from [1] to [586].
tWR
The Min Write Recovery Time Range is from [1] to [38].
tRFC
The Min Refresh Recovery Delay Time Range is from [1] to [9363].
tRRD
The Min Row Active to Row Active Delay Time Range is from [1] to [38].
tWTR
39
The Min Internal Write to Read Command Delay Time Range is from [1] to [38].
tRTP
The Min Internal Read to Precharge Command Delay Time Range is from [1] to
[38].
tRC
The Min Active to Active/Refresh Delay Time (tRCmin) Range is from [1] to [586].
tFAW
The Min Four Active Window Delay Time Range is from [1] to [586].
tCWL
Use this item to setup Minimum CAS Write Latency Time (tCWLmin).
tREFI
Use this item to setup Maximum tREFI Time (Average Periodic Refresh Interval).
Command Rate
Use this item to setup Memory Command Rate Option.
The optional settings are [Auto]; [1T]; [2T].
3-12 Save & Exit Menu
 Save Changes and Reset
This item allows user to reset the system after saving the changes.
40
 Discard Changes and Reset
This item allows user to reset the system without saving any changes.
Save Options
 Save Changes
This item allows user to save changes done so far to any of the setup options.
 Discard Changes
This item allows user to discard changes done so far to any of the setup options.
 Restore Defaults
Use this item to restore /load default values for all the setup options.
 Save as User Defaults
Use this item to save the changes done so far as user defaults.
 Restore User Defaults
Use this item to restore defaults to all the setup options.
Boot Override
 Launch EFI Shell from filesystem device
Use this item to Launch EFI Shell application (Shellx64.efi) from one of the
available filesystem devices.
41