ECx Ethernet Control Guide - akmedia.[bleep]

ECx Ethernet Control
for VENUE Systems
PN 9321-62788-00 REV A 08/10
Legal Notices
This guide is copyrighted ©2010 by Avid Technology, Inc., (hereafter “Avid”), with
all rights reserved. Under copyright laws, this guide may not be duplicated in
whole or in part without the written consent of Avid.
003, 96 I/O, 96i I/O, 192 Digital I/O, 192 I/O, 888|24 I/O, 882|20 I/O,
1622 I/O, 24-Bit ADAT Bridge I/O, AudioSuite, Avid, Avid DNA, Avid Mojo,
Avid Unity, Avid Unity ISIS, Avid Xpress, AVoption, Axiom, Beat Detective,
Bomb Factory, Bruno, C|24, Command|8, Control|24, D-Command, D-Control,
D-Fi, D-fx, D-Show, D-Verb, DAE, Digi 002, DigiBase, DigiDelivery, Digidesign,
Digidesign Audio Engine, Digidesign Intelligent Noise Reduction, Digidesign
TDM Bus, DigiDrive, DigiRack, DigiTest, DigiTranslator, DINR, DV Toolkit,
EditPack, Eleven, HD Core, HD Process, Hybrid, Impact, Interplay, LoFi, M-Audio,
MachineControl, Maxim, Mbox, MediaComposer, MIDI I/O, MIX, MultiShell,
Nitris, OMF, OMF Interchange, PRE, ProControl, Pro Tools M-Powered, Pro Tools,
Pro Tools|HD, Pro Tools LE, QuickPunch, Recti-Fi, Reel Tape, Reso, Reverb One,
ReVibe, RTAS, Sibelius, Smack!, SoundReplacer, Sound Designer II, Strike,
Structure, SYNC HD, SYNC I/O, Synchronic, TL Aggro, TL AutoPan, TL Drum
Rehab, TL Everyphase, TL Fauxlder, TL In Tune, TL MasterMeter, TL Metro,
TL Space, TL Utilities, Transfuser, Trillium Lane Labs, Vari-Fi Velvet, X-Form, and
XMON are trademarks or registered trademarks of Avid Technology, Inc. Xpand!
is Registered in the U.S. Patent and Trademark Office. All other trademarks are
the property of their respective owners.
Product features, specifications, system requirements, and availability are
subject to change without notice.
Guide Part Number 9321-62788-00 REV A 08/10
Documentation Feedback
At Avid, we are always looking for ways to improve our documentation. If you have
comments, corrections, or suggestions regarding our documentation, email us
at techpubs@avid.com.
Contents
Chapter 1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
ECx Capabilities and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
ECx Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
System Requirements and Compatibility Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
About This Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
About www.avid.com . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chapter 2. Installing ECx Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installing ECx Host Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installing the ECx Client Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Uninstalling ECx Host Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Reinstalling ECx Host Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Chapter 3. Configuring and Using ECx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connecting a Computer Directly to VENUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connecting a Wireless Router or WAP to VENUE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Setting VENUE and Client IP Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Establishing a Wireless Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Enabling Remote Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Disconnecting ECx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Changing the Ethernet Control Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Contents iii
iv ECx Ethernet Control
Chapter 1: Overview
Welcome to ECx Ethernet Control for Avid VENUE systems.
ECx lets you control a VENUE system remotely over an Ethernet network using compatible wired or wireless network
equipment (purchased separately).
ECx Capabilities and Features
System Requirements and
Compatibility Information
The following are required to use ECx:
• A VENUE system that has already been installed and configured, running VENUE software 1.1 or higher
• A qualified router or wireless access point (WAP) device
ECx provides the following:
• Remote control of a VENUE system from a client computer, including a laptop or Tablet PC
• Exact duplication of VENUE software on the remote client computer
• A client computer running qualified Windows or Mac OS X
software with wired or wireless Ethernet capability.
• For wireless communication with ECx, 802.11g capable devices (or faster) are recommended.
Avid can only assure compatibility and provide support for
hardware and software it has tested and approved.
ECx Components
The ECx package includes the following items:
• ECx card (pre-installed in the VENUE FOH Rack, VENUE
Mix Rack and the VENUE SC48™)
For complete system requirements and a list of qualified computers, operating systems, hard drives, and third-party devices, visit:
www.avid.com/compatibility
• Ethernet cable for connecting the ECx card to your client
computer, wireless router, or wireless access point device
• ECx Ethernet Control Software installer CD-ROM (containing ECx host and client software)
Chapter 1: Overview 1
About This Guide
About www.avid.com
This guide provides installation and operational instructions
for using ECx Ethernet Control.
The Avid website (www.avid.com) is your best online source
for information to help you get the most out of your system.
The following are just a few of the services and features available.
For complete instructions on connecting and configuring
your VENUE system, see the VENUE D-Show, VENUE Profile,
or VENUE SC48 guide.
Conventions Used in This Guide
All of our guides use the following conventions to indicate
menu choices and key commands:
:
Convention
Action
File > Save
Choose Save from the
File menu
Control+N
Hold down the Control key
and press the N key
Control-click
Hold down the Control key
and click the mouse button
Right-click
Click with the right
mouse button
The names of Commands, Options, and Settings that appear
on-screen are in a different font.
The following symbols are used to highlight
important information:
User Tips are helpful hints for getting the
most from your system.
Important Notices include information that
could affect your data or the performance of
your system.
Shortcuts show you useful keyboard or
mouse shortcuts.
Cross References point to related sections in
this guide and other VENUE guides.
2 ECx Ethernet Control
Product Registration Register your purchase
online.
Support and Downloads Contact Avid Customer Success (technical support); download software updates and the latest online manuals; browse the Compatibility documents for system
requirements; search the online Knowledge Base or join the
worldwide Avid community on the User Conference.
Training and Education Study on your own using courses available online or find out how you can learn in a classroom setting at a certified training center.
Products and Developers Learn about Avid
products; download demo software or learn about our Development Partners and their plug-ins, applications, and hardware.
News and Events Get the latest news from Avid or sign up for
a product demo.
Chapter 2: Installing ECx Software
To use ECx Ethernet Control, you must do the following:
• Install the ECx host software on your VENUE system.
• Install the ECx client software on your remote computer.
If you need to uninstall the ECx host software from your
VENUE system, see “Uninstalling ECx Host Software” on
page 4.
If you need to re-install the ECx host software, (after a System
Restore or an Update), see “Reinstalling ECx Host Software”
on page 4.
After you install the host and client software, see Chapter 3,
“Configuring and Using ECx” for information on setting up
your VENUE system and client computer for remote operation
using ECx.
Installing the ECx Client Software
The ECx Ethernet Control Software installer CD-ROM contains remote control applications for both Windows and Mac
platforms.
Installing the ECx Client in Windows
To install the ECx control client application (“UltraVNC”) in
Windows:
1 Insert the ECx installer disc in the computer CD or DVD
drive.
2 Open the Windows Client folder.
3 Double-click the “UltraVNC-Viewer.exe” file.
4 Follow the on-screen installation instructions to complete
Installing ECx Host Software
The ECx Ethernet Control Software installer disc contains the
ECx host software. This software enables your VENUE system
to communicate with computers running the remote client
software.
To install ECx host software on your VENUE system:
1 Insert the ECx installer disc in VENUE’s CD-ROM drive.
2 Do one of the following to put your system into Config
Mode:
• Press the Console Config switch on the console.
– or –
the installation.
Installing the ECx Client on Mac
To install the ECx control client application (“Chicken of the
VNC”) on Mac:
1 Insert the ECx installer disc in the computer CD or DVD
drive.
2 Open the Mac OS X Client folder.
3 Double-click the “cotvnc-20b4.dmg” file.
4 In the window that opens, drag the “Chicken of the VNC”
icon to copy it to a location on your hard drive.
• Double-click the Mode box in the bottom-right corner of
the screen.
3 Go to Options > System Config and click Update.
4 Click Yes to exit VENUE software and begin the installation.
5 After the ECx software installation is complete, VENUE soft-
ware restarts.
Whenever you perform an Update or a System Restore of
your VENUE system, you must reinstall the ECx host software. See “Reinstalling ECx Host Software” on page 4.
Chapter 2: Installing ECx Software 3
Uninstalling ECx Host Software
Reinstalling ECx Host Software
If you need to uninstall ECx software from your VENUE system, you can do so from the system desktop.
If ECx is installed on your VENUE system, you will have to reinstall the ECx host software after performing a System Restore or an Update.
To uninstall ECx host software from your VENUE system:
1 Do one of the following to put your system into Config
Mode:
System Restore If you perform a complete System Restore, the
ECx host software must be reinstalled from its original installer disc. See “Installing ECx Host Software” on page 3.
• Press the Console Config switch on the console
2 Go to Options > System Config.
Update If you perform an Update, you must still reinstall the
ECx host software. You can reinstall without using the ECx installer disc because an Update leaves the ECx installer on your
VENUE system’s hard drive. You can also reinstall using the
original installer disc.
3 Hold the Control key and click Shut Down to go to the sys-
To reinstall after an Update without using the ECx installer disc:
– or –
• Double-click the Mode box in the bottom-right corner of
the screen.
tem desktop.
1 Remove any USB key disks from all USB ports, and make
4 Locate and double-click the ECx host software uninstall pro-
sure no installer discs are in the CD-ROM drive.
gram (C:\Program Files\D-Show Ethernet Control Software\
Uninstall.bat).
2 Do one of the following to put your system into Config
The ECx host software is uninstalled, and the VENUE software
automatically restarts.
The ECx folder will remain on your VENUE system hard
drive after uninstalling,
Mode:
• Press the Console Config switch on the console.
– or –
• Double-click the Mode box in the bottom-right corner of
the screen.
3 Go to the Options > Systems page.
4 Click the Update button.
4 ECx Ethernet Control
Chapter 3: Configuring and Using ECx
Overview
You can control your VENUE system (the “host”) with a remote computer (the “client”) using standard VNC (Virtual
Network Computing) protocol over TCP/IP, allowing remote
access to your system via a wired or wireless Ethernet-based
network. This chapter covers the steps for configuring and using ECx.
For a wired network, the steps include:
 Connecting the remote computer directly to your VENUE
system using an Ethernet cable.
Windows To connect a Windows computer directly to your
VENUE system, an Ethernet crossover cable is required. Alternatively, you can use an Ethernet hub and connect standard
Ethernet cables between your VENUE system, the hub and the
remote computer.
Mac To connect a Mac computer directly to your VENUE system, you can use either a standard Ethernet cable or an Ethernet crossover cable.
2 Configure the VENUE system and the client computer IP addresses manually. See “Setting IP Addresses Manually” on
page 6.
 Setting the IP addresses of your VENUE system and your client computer manually.

Enabling remote operation of your VENUE system.
For a wireless network, the steps include:
Connecting a wireless router or a wireless access point
(WAP) device to your VENUE system.

Setting the IP addresses of your VENUE system and your client computer manually or automatically.

 Establishing a connection between your wireless router and
the client computer.

Enabling remote operation of your VENUE system.
Connecting a Computer Directly to
VENUE
If you are establishing a fixed remote control station and do
not need a mobile connection, you can connect the remote
computer directly to your VENUE system using an Ethernet
cable.
Connecting a Wireless Router or WAP
to VENUE
VENUE systems work with standard wireless routers or WAP
devices.
Before connecting a wireless router or WAP device, you should
configure the SSID of the device so that its wireless network
can be easily identified on the client computer. You can specify any unique network name for the device, such as “VENUE
Network.”
To configure the SSID and any network security features of
your wireless router or WAP, refer to the manufacturer’s instructions.
To connect a wireless router or WAP device to a VENUE system:
1 Connect one end of the appropriate type of Ethernet cable
to the ECx port and the other end to the Ethernet connector
port on the router or WAP. Do one of the following depending
on the type of device you are using
To connect a computer directly to your VENUE system:
• If you are using a wireless router, use a standard Ethernet
cable to your VENUE system.
1 Connect one end of the appropriate Ethernet cable type
– or –
(with RJ-45 connectors) to the ECx port on your VENUE system, and the other end to the Ethernet port on the computer.
The type of cable depends on the operating system of the remote computer:
• If you are using a WAP, use an Ethernet crossover cable to
connect to your VENUE system.
Chapter 3: Configuring and Using ECx 5
2 Do one of the following:
Setting IP Addresses Manually
• If you are using a wireless router or WAP device that does
not include a DHCP server function (such as the Cisco Aironet 1230AG), you must configure your VENUE system
and the client computer IP addresses manually. See “Setting IP Addresses Manually” on page 6.
Set VENUE and client computer IP addresses manually if you
are connecting a computer directly to your VENUE system, or
you are using a wireless router or WAP device that does not include a DHCP server function.
– or –
Setting a VENUE System IP Address Manually
• If you are using a wireless router that includes a DHCP
server function (such as the Belkin Pre-N), you can configure your VENUE system and the client computer to set
the IP addresses automatically. See “Setting VENUE and
Client IP Addresses Automatically” on page 8.
To manually set the IP address for your VENUE system:
1 In VENUE software, go to Options > Interaction.
2 In the Ethernet Control section, click Network Settings.
Setting VENUE and Client IP Addresses
You can set the IP addresses of your VENUE system and client
computer manually or automatically depending on the configuration of your network:
 If you are connecting a computer directly to your VENUE
system, or you are using a wireless router or WAP device that
does not include a DHCP server function, see “Setting IP Addresses Manually” on page 6.
– or –
If you are using a wireless router that includes a DHCP
server function, see “Setting VENUE and Client IP Addresses
Automatically” on page 8.

IP configuration changes on your VENUE system and client
computer can take up to 2 minutes to become effective. After making changes, be sure to allow sufficient time for the
system to assign IP addresses and establish communication
between all the components. If network communication is
not established after allowing sufficient time for IP addressing, check all cables and connections.
Ethernet Control section of the Interaction page
3 Click Use the Following Address and enter the following:
• IP address: 10.0.0.1
• Subnet Mask: 255.255.255.0
• Default Gateway: 10.0.0.1
Setting an IP address manually
4 Click Apply.
5 Select Enable Remote Control to activate the VENUE ECx
host.
6 Go to “Setting the Client Computer IP Address Manually”
on page 7.
6 ECx Ethernet Control
Setting the Client Computer IP Address Manually
After manually setting your VENUE system’s IP address, you
need to set your client computer’s IP address.
Windows
To manually set the IP address in Windows:
1 Go to Control Panels > Network Connections, and do one of
the following:
• If you are connecting the computer directly to your
VENUE system, right-click the Local Area Connection
icon and choose Properties.
– or –
• If you are connecting using a wireless router or WAP,
right-click the Wireless Network Connection icon and
choose Properties.
Internet Protocol Properties window
4 Click OK to close the Internet Protocol properties window.
5 Click OK to close the Network Connection Properties window.
6 Do one of the following depending on the configuration of
your network:
• If you are using a wireless network, go to “Establishing a
Wireless Connection” on page 9.
– or –
• If you are using a wired network, go to “Enabling Remote
Operation” on page 10.
Mac
To manually set the IP address on a Mac:
Local Area Connection Properties window
1 Launch System Preferences > Network.
2 In the Connection Properties window, double-click
2 Do one of the following:
Internet Protocol (TCP/IP).
3 In the Internet Protocol Properties window, select Use the
following IP Address and enter the following:
• If you are connecting the computer directly to your
VENUE system, choose Ethernet from the network connections services list.
• IP address: 10.0.0.2
– or –
• Subnet Mask: 255.255.255.0
• If you are connecting using a wireless router or WAP,
choose Airport from the network connections services
list.
• Default Gateway: (none required)
3 Choose Manually from the Configure pop-up menu.
Chapter 3: Configuring and Using ECx 7
4 Enter the following:
• IP address: 10.0.0.2
3 In the Ethernet Control window, select Obtain Address Auto-
matically.
• Subnet Mask: 255.255.255.0
• Router: (none required)
Configuring Ethernet Control in VENUE
4 Click Apply.
5 Wait until the VENUE system is assigned an IP address. This
may take time (up to two minutes). If no DHCP server is
found, the VENUE system will self-assign an IP address.
Network Preferences window
5 Click Apply.
6 Do one of the following depending on the configuration of
your network:
• If you are using a wireless network, go to “Establishing a
Wireless Connection” on page 9.
Make a note of the IP address assigned to your VENUE system, as you will need to enter it into the client software.
6 Select Enable Remote Control to activate the VENUE system
ECx host. Your system’s status will be displayed as “Waiting
for connection.”
7 Go to “Setting a Client Computer IP Address Automatically”
on page 8.
– or –
• If you are using a wired network, go to “Enabling Remote
Operation” on page 10.
Setting VENUE and Client IP Addresses
Automatically
You can configure your VENUE system and client computer to
set their IP addresses automatically using DHCP. Set the IP automatically if you are using a wireless router that includes a
DHCP server function.
Setting a Client Computer IP Address
Automatically
After setting the IP address for your VENUE system using
DHCP, you need to do the same for your client computer.
Windows
To automatically set the IP address in Windows:
1 Go to Control Panel > Network Connections.
2 Right-click the Wireless Network Connection icon and
Setting the VENUE IP Address Automatically
To set the IP address of your VENUE system automatically:
choose Properties.
3 In the Connection Properties window, double-click Internet
Protocol (TCP/IP).
1 In the VENUE software, go to the Options page and click the
Interaction tab.
2 In the Ethernet Control section, click Network Settings.
Ethernet Control section of the Interaction page
Connection Properties window
8 ECx Ethernet Control
4 In the Internet Protocol Properties window, select “Obtain
an Address Automatically.”
Establishing a Wireless Connection
Once IP addresses are set, you can establish a connection from
the client computer to the wireless network.
Windows
To establish a wireless connection in Windows:
1 Go to Control Panel > Network Connections.
2 Right-click the Wireless Network Connection icon and
choose Properties.
3 In the Connection Properties window, click the Wireless
Networks tab.
Internet Protocol (TCP/IP) Properties window
5 Click OK to close the Internet Protocol properties window.
6 Click OK to close the Network Connection Properties window.
7 Go to “Enabling Remote Operation” on page 10.
Mac
To automatically set the IP address on a Mac:
1 Launch System Preferences > Network.
2 Choose Airport from the network connections services list.
3 Click the Advanced button, then click the TCP/IP tab.
4 Choose Using DHCP from the Configure IPv4 menu.
Configuring a wireless connection in Windows
4 Under Preferred Networks, click Add, and type the SSID of
the wireless router or WAP device connected to your VENUE
system.
5 Choose the Network Authentication and Data Encryption
settings to match the corresponding router or WAP configuration settings.
Airport Network Advanced window
5 Click OK.
6 Go to “Enabling Remote Operation” on page 10.
Entering an SSID and choosing settings in Windows
6 Click OK. The VENUE SSID should appear in the list of available wireless networks.
7 Go to “Enabling Remote Operation” on page 10.
Chapter 3: Configuring and Using ECx 9
Mac
Enabling Remote Operation
To establish a wireless connection on Mac:
1 Go to System Preferences > Network.
2 Choose Airport from the network connections services list.
3 From the Network Name pop-up menu, choose your net-
work.
In order to enable remote operation of your VENUE system,
you need to have obtained valid IP addresses for your VENUE
system and your client computer. If you are using a wireless
network, you also need to have established a network between
the wireless router or WAP device that is connected to your
VENUE system and your client computer.
To enable remote operation with a Windows client computer:
1 Double-click the “ECx Ethernet Control (UltraVNC
Viewer)” icon on your desktop (or go to Start Menu > Programs > UltraVNC > Run UltraVNC Viewer) to launch the UltraVNC Viewer application.
2 Enter the IP address of the ECx host (your VENUE system).
3 Click Connect.
4 Enter the password when prompted (VENUE’s default pass-
word is “password”) and click Connect.
Configuring a wireless connection on the Mac
If your network does not appear in the Network Name
pop-up menu, choose “Join Other Network, type in the
name of your network, and click Join. To assign your wireless router or WAP device a network name, see your device’s
documentation.
4 Go to “Enabling Remote Operation” on page 10.
UltraVNC Viewer window
The client launches and displays the VENUE system screen.
You can then view and operate all on-screen controls from the
client computer.
To enable remote operation with a Mac client computer:
1 Double-click the “Chicken of the VNC” icon to launch the
application.
2 Enter the IP address of the ECx host (your VENUE system).
3 Enter the password (VENUE’s default password is “pass-
word”) and click Connect.
Chicken of the VNC window
The client launches and displays the VENUE system screen.
You can then view and operate all on-screen controls from the
client computer.
10 ECx Ethernet Control
Disconnecting ECx
To disconnect ECx:
1 Close the ECx client application by doing one of the follow-
ing:
• In Windows, move the pointer to the top of the screen
until the control strip appears, and click the close box.
– or –
• On Mac, press Command+Q to quit.
2 On the VENUE system, deselect Enable Remote Control in the
Ethernet Control section of the Options > Interaction page.
Changing the Ethernet Control
Password
You can change the password that users need to enter in order
to control your VENUE system from a remote client.
By default, the VENUE Ethernet Control password is
“password” (all lowercase).
To change the Ethernet Control password:
1 In the Ethernet Control section of the Options > Interaction
page, double-click the Password field.
2 Enter a new password and press Enter.
Make a note of the new password and your system’s IP address, as you will need to enter it into the client software.
Chapter 3: Configuring and Using ECx 11
Avid
Technical Support (USA)
Product Information
2001 Junipero Serra Boulevard
Daly City, CA 94014-3886 USA
Visit the Online Support Center at
www.avid.com/support
For company and product information,
visit us on the web at www.avid.com