cover german.qxd
17.03.2005
17:29
Seite 1
ampire
Hinter CLIFFORD® steht
Langwadenerstraße 60
D-41516 Grevenbroich
02181-81955-0
www.ampire.de
Directed Electronics.
Technischer Support
02181-81955-54
info@ampire.de
nur das eine Ziel, dem Kunden die best-
Seit der Firmengründung hat Directed
möglichen Autoalarm- und Autohifiprodukte zu liefern, die auf dem Markt
erhältlich sind.
Die Produkte von Directed Electronics
werden weltweit verkauft. Ein technischer Kundenservice ist in fast jedem
Land erhältlich.
Für
nähere
Informationen
über
Auslandsniederlassungen wählen Sie:
Europa: +49-2181-81955-0
© 2005 Ampire Electronics. Alle Rechte vorbehalten.
M A T R I X
Directed Electronics is committed to delivering
world class quality products and services that
excite and delight our customers.
Directed ist ISO 9001 zertifiziert.
[ MONTAGE]
2.5X
The Bitwriter® (p/n 998T)
requires chip version 1.4 or
newer to program this unit.
Bitwriter™, Code Hopping™, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn
Routine™, Nite-Lite®, Nuisance Prevention® Circuitry, NPC®, Revenger®, Silent Mode™,
Soft Chirp®, Stinger®, Valet®, Vehicle Recovery System®, VRS®, and Warn Away® are all
Trademarks or Registered Trademarks of Directed Electronics, Inc.
www.directechs.com
DirectFax 800-999-1329 Technical Support 800-753-0800
These resources are for authorized Directed Dealer use only.
Table of Contents
Primary Harness (H1) Wire Connection Guide ............................................................................4
Primary Harness Wiring Diagram.............................................................................................4
Primary Harness Wiring Instructions........................................................................................4
Door Lock Harness (H2), 3-PIN Connector ..............................................................................10
Peripheral Plug-In Harnesses.......................................................................................................10
Super Bright LED, 2-Pin WHITE Plug..................................................................................10
Valet/Program Switch, 2-Pin BLUE Plug ................................................................................11
Programmer Interface, 3-Pin BLACK Plug .............................................................................11
Mounting the Receiver/Antenna .............................................................................................11
Shock Sensor Harness, 4-Pin White Plug................................................................................12
Programming Jumper .................................................................................................................13
Light Flash Jumper..................................................................................................................13
Bypassing Sensor Inputs ..............................................................................................................14
System Features Learn Routine ...................................................................................................14
System Features Menus ...............................................................................................................17
Menu #1 - Basic Features ........................................................................................................17
Menu #2 - Advanced Features.................................................................................................17
Feature Descriptions ...................................................................................................................18
Menu #1 - Basic Features ........................................................................................................18
Transmitter/Receiver Learn Routine ...........................................................................................21
Standard Configuration...........................................................................................................23
Single Button Arm/Disarm Configuration ..............................................................................23
Diagnostics .................................................................................................................................24
Arm/Disarm Diagnostics.........................................................................................................24
System Status Chirps...............................................................................................................24
Table of Zones ........................................................................................................................24
Long Term Event History ...........................................................................................................25
Multi-Level Security Arming .......................................................................................................25
Optional Vehicle Recovery System (VRS) ...................................................................................25
Nuisance Prevention® Circuitry .................................................................................................26
Rapid Resume Logic ...................................................................................................................26
Troubleshooting ..........................................................................................................................26
Wiring Quick Reference Guide ...................................................................................................28
©
2003 Directed Electronics, Inc.
3
Primary Harness (H1) Wire Connection Guide
Primary Harness Wiring Diagram
H1/1
___ ORANGE
H1/2
___ WHITE
H1/3
___ WHITE/BLUE
H1/4
___ BLACK/WHITE
H1/5
___ GREEN
H1/6
___ BLUE
H1/7
___ VIOLET
(+) Door Trigger Input, Zone 3
H1/8
___ BLACK
(-) Chassis Ground Input
H1/9
___ YELLOW
H1/10
___ BROWN
H1/11
___ RED
H1/12
___ RED/WHITE
(-) 500 mA Armed Output
(+)/(-) Selectable Light Flash Output
(-) 200 mA Channel 3 Programmable Output
(-) 200 mA Domelight Supervision Output
(-) Door Trigger Input, Zone 3
(-) Instant Trigger Input, Zone 1
(+) Switched Ignition Input, Zone 5
(+) Siren Output
(+) Constant Power Input
(-) 200 mA Channel 2 Output
Primary Harness Wiring Instructions
This guide describes in detail the connection of each wire. Also included are possible applications
of each wire. This system was designed with the ultimate in flexibility and security in mind. Many
of the wires have more than one possible function. Please read carefully to ensure a thorough understanding of this unit.
H1/1 ORANGE (-) ground-when-armed output
This wire supplies a (-) ground as long as the system is armed. This output ceases as soon as the
system is disarmed. The ORANGE wire is pre-wired to control the 8618 starter kill relay. It can
supply up to 500 mA of current.
NOTE: If using the H1/1 ORANGE wire to activate an add-on accessory such as window
automation, pager or voice module a 1Amp diode must be installed to ensure proper operation.
Insert the diode as shown in the following diagram.
IMPORTANT! Never interrupt any wire other than the starter wire.
4
©
2003 Directed Electronics, Inc.
H1/2 WHITE (+/-) light flash output
As shipped, the H1/2 WHITE wire should be connected to the (+) parking light wire. If the light flash
polarity jumper is moved to the (-) position (see the Programming Jumper section of this installation
guide), this wire supplies a (-) 200 mA output. This is suitable for driving (-) light control wires in
Toyota, Lexus, BMW, some Mitsubishi, some Mazda, and other models.
NOTE: For parking light systems that draw 10 amps or more, the jumper must be switched to a
(-) light flash output (see the Programming Jumpers section of this guide). P/N 8617 or a standard
automotive SPDT relay must be used on the H1/2 light flash output wire.
IMPORTANT! DO NOT connect this wire to a negative vehicle light flash wire before
changing the programming jumper to the negative polarity position or damage to
vehicle light circuit may occur.
H1/3 WHITE/BLUE 200 mA (-) channel 3 output
This wire provides a (-) 200 mA output whenever the transmitter button(s) controlling Channel 3
©
2003 Directed Electronics, Inc.
5
is pressed. This output can be programmed to provide the following types of output (see System
Features Learn Routine section of this guide):
➤
➤
➤
➤
➤
A validity output will send a signal as long as the transmission is received.
A latched output will send a signal continuously when the Channel 3 button(s) is pressed and
released. The signal will continue until channel three is pressed again.
A latched/reset with ignition output works similar to the latched output, but will also reset
(output will stop) when the ignition is turned on and then off.
A 30 second timed output will send a signal for 30 seconds when channel three is pressed. This
output can be shut off during the 30-second period by pressing Channel 3 again.
This output can also be programmed to provide a second unlock pulse when the unlock button
is pressed a second time after disarming the system. This can be used to unlock the passenger
doors when installing progressive door locks.
IMPORTANT! Never use this wire to drive anything but a relay or a low-current input!
This transistorized output can only supply 200 mA, and connecting directly to a
solenoid, motor, or other high-current device will cause the module to fail.
H1/4 BLACK/WHITE (-) 200 mA domelight supervision output
Connect the H1/4 wire to the optional domelight supervision relay as shown in the following
diagram:
IMPORTANT! This output is only intended to drive a relay. It cannot be connected
directly to the domelight circuit, as the output cannot support the current draw of one
or more bulbs.
6
©
2003 Directed Electronics, Inc.
H1/5 GREEN (-) door trigger input
Most vehicles use negative door trigger circuits. Connect the GREEN wire to a wire showing
ground when any door is opened. When connecting to newer model vehicles there is generally a
need to use individual door triggers. See DirectFax document 1076 for wiring instructions. This
wire will report Zone 3.
NOTE: If using a door trigger wire that has a delay, Advanced Menu 2, feature 6, or the 998T
Bitwriter can be used to turn Bypass Notification off.
H1/6 BLUE (-) instant trigger input
This input will respond to a negative input with an instant trigger. It is ideal for hood and trunk pins
and will report on Zone 1. It can also be used with Directed single-stage sensors. The H1/6 BLUE
instant trigger wire can also be used to shunt sensors during operation of auxiliary channels or remote
start. (See Bypassing Sensor Inputs section of this guide.)
NOTE: If this wire is used for hood or hood and trunk, the remote control must be
reprogrammed to reflect the vehicle entries used (see owner’s guide).
H1/7 VIOLET (+) door trigger input
This type of dome circuit is used in many Ford products. Connect the VIOLET wire to a wire that
shows (+)12V when any door is opened. This wire will report Zone 3.
NOTE: If using a door trigger wire that has a delay, Advanced Menu 2, feature 6, or the 998T
Bitwriter can be used to turn Bypass Notification off.
©
2003 Directed Electronics, Inc.
7
H1/8 BLACK (-) chassis ground connection
Connect this wire to a clean, paint-free sheet metal location (driver kick panel) using a factory bolt
that DOES NOT have any vehicle component grounds attached to it. A screw should only be used
when in conjunction with a two-sided lock washer. Under dash brackets and door sheet metal are
not acceptable ground points. It is recommended that all security components be grounded at the
same location.
H1/9 YELLOW (+) ignition input
Connect this wire to the (+) 12 volts ignition wire. This wire is pre-wired to the starter kill relay and
must show (+) 12 volts with the key in RUN position and during cranking. Take great care that this
wire cannot be shorted to the chassis at any point.
8
©
2003 Directed Electronics, Inc.
H1/10 BROWN (+) siren output
Connect this to the RED wire of the Revenger® siren. Connect the BLACK wire of the siren to (-)
chassis ground, preferably at the same point you connect the control module’s BLACK ground wire.
H1/11 RED (+)12V constant power input
Before connecting this wire, remove the supplied fuse. Connect to the battery positive terminal or
the constant 12V supply to the ignition switch.
NOTE: Always use a fuse within 12 inches of the point you obtain (+)12V. Do not use the 15 fuse
in the harness for this purpose. This fuse protects the module itself.
H1/12 RED/WHITE 200 mA (-) channel 2 output
When the system receives the code controlling channel 2 for longer than 1.5 seconds, the
RED/WHITE will supply an output as long as the transmission continues. This is often used to
operate a trunk/hatch release or other relay/driven function.
IMPORTANT! Never use this wire to drive anything but a relay or a low-current input!
The transistorized output can only supply 200 mA of current. Connecting directly to a
solenoid, motor, or other high-current device will cause it to fail.
©
2003 Directed Electronics, Inc.
9
Door Lock Harness (H2), 3-PIN Connector
H2/A
___ Green
(-) Lock, (+) Unlock Output
H2/B
___ Empty
Unless Using 451M
H2/C
___ Blue
(-) Unlock, (+) Lock Output
IMPORTANT! The door lock outputs are low current and should not be attached
directly to any high current device; they are only to be used to activate relays
NOTE: For detailed instructions about connecting to the vehicle’s power door lock systems, refer
to the Door Lock Wiring guide (Document No. 1041) available to authorized dealers only from the
technical resources listed at the front of this guide.
Peripheral Plug-In Harnesses
Super Bright LED, 2-Pin WHITE Plug
The super bright LED operates at (+) 2 volt DC and plugs into the two-pin WHITE port. Make
sure the LED wires are not shorted to ground as the LED will be damaged. Multiple LED’s can be
used, but they must be wired in series. The LED fits into a 9/32-inch mounting hole. Be sure to
check for clearance prior to drilling the mounting hole.
NOTE: Never use a BLUE LED in combination with a RED LED.
DIA-41
10
©
2003 Directed Electronics, Inc.
Valet/Program Switch, 2-Pin BLUE Plug
The Valet/Program button should be accessible from the driver’s seat. It plugs into the BLUE port
on the side of the unit. Since the system features Valet® by using the remote transmitter, the button
can be well hidden. Consider how the button will be used before choosing a mounting location.
Check for rear clearance before drilling a 9/32-inch hole and mounting the button.The GRAY wire
in the two-pin plug may also be used as a (+) ghost switch input and can be connected to any (+)
switch in the vehicle. (See Feature Descriptions section of this guide.)
Programmer Interface, 3-Pin BLACK Plug
The BLACK three-pin port is provided for programming of the unit. When using the 998T
Bitwriter, it is possible to configure any and all of the programmable functions. For more information please refer to the guide packaged with the programmer. This port can also be used to interface
with Directed Video components for on-screen security system programming and trigger information.
Mounting the Receiver/Antenna
Receiver/antenna position should be discussed with the vehicle’s owner prior to installation, since
the antenna may be visible to the vehicle’s operator.
The best location for the receiver/antenna is centered high on either the front or rear windshield.
For optimal range, the antenna should be mounted horizontally. It can be mounted vertically in
relation to the windshield or under the dashboard away from metal, but range will be diminished.
Metallic window tint can also affect range, so this should be a consideration when determining the
mounting location.
After determining the best mounting location, follow these steps:
1. Clean the mounting area with a quality glass cleaner or alcohol to remove any dirt or residue.
2. Plug the receiver/antenna cable into the receiver/antenna.
©
2003 Directed Electronics, Inc.
11
3. Mount the receiver/antenna using the supplied double-sided tape.
4. Route the receiver/antenna cable to the control module and plug it into the four-pin antenna
connector.
IMPORTANT! To achieve the best possible range, DO NOT leave the antenna cable
bundled under the dash. Always extend the cable full length during installation,
regardless of the antenna mounting location.
TWO-WAY IN-VEHICLE
TRANSCEIVER CABLE
TWO-WAY IN-VEHICLE
TRANSCEIVER
DRW-365
CONTROL
MODULE
Shock Sensor Harness, 4-Pin White Plug
GREEN (-) Multiplex Input
Inputs shorter than 0.8 seconds will trigger the Warn Away® response, while inputs longer than 0.8
seconds will trigger full alarm sequence and report Zone 4.
NOTE: If installing an optional Directed dual-stage sensor, connect to the GREEN wire. The
following diagram eliminates the need for diodes to isolate the sensors, as well as providing a
separate zone for each sensor.
Diagram for adding optional Directed dual stage sensor to GREEN wire (zone 4).
12
©
2003 Directed Electronics, Inc.
BLUE (-) Multiplex Input
Inputs shorter than 0.8 seconds will trigger the Warn Away® response, while inputs longer than 0.8
seconds will trigger full alarm sequence and report Zone 2.
RED (+) 12V Constant and BLACK (-) Ground
Do not use these for anything besides the plug-in shock sensor.
Programming Jumper
Light Flash Jumper
This jumper is used to determine the light flash output. In the (+) position, the on-board relay is
enabled and the unit will output (+)12V on the WHITE wire, H1/2. In the (-) position, the onboard relay is disabled. The WHITE wire, H1/2, will supply a 200 mA (-) output suitable for
driving factory parking light relays.
NOTE: For parking light circuits that draw 10 amps or more, the jumper must be switched to a (-)
light flash output. P/N 8617 or a standard automotive SPDT relay must be used on the H1/2 light
flash output harness wire.
IMPORTANT! DO NOT connect the H1/2 light flash wire to a negative vehicle light
flash wire before changing the programming jumper to the negative polarity position or
damage to vehicle light circuit may occur.
©
2003 Directed Electronics, Inc.
13
Bypassing Sensor Inputs
There are times when you need to temporarily bypass all sensor inputs to the unit, such as when
remote starting the vehicle. Anytime an auxiliary channel output is used, all inputs are bypassed for
five seconds. During the five second bypass period, ground can be supplied to the H1/6 BLUE wire
without triggering the unit. When the five second bypass period ends, if the unit sees ground on
the H1/6 BLUE wire, all trigger inputs except the door trigger input will remain bypassed until five
seconds after ground is removed from the BLUE wire. This can be done using the status output of
a Directed Electronics remote engine starting unit as shown in the following diagram:
System Features Learn Routine
The System Features Learn Routine dictates how the unit operates. Due to the number of steps,
they have been broken up into two menus. It is possible to access and change any of the feature
settings using the Valet/Program switch. However, this process can be greatly simplified by using the
998T Bitwriter. Any of the settings can be changed and then assigned to a particular transmitter, up
to four, a feature called Owner Recognition. Each time that particular transmitter is used to disarm
the system, the assigned feature settings will be recalled. Owner Recognition is only possible when
programming the unit via the 998T Bitwriter.
If the system was previously programmed using the 998T Bitwriter, the learn routine may be
locked. If the siren generates one long chirp when attempting to program the unit, the learn routine
is locked and must be unlocked using the 998T Bitwriter.
1. Open a door. (The H1/5 GREEN wire or the H1/7 VIOLET wire must be
connected.)
14
©
2003 Directed Electronics, Inc.
2. Ignition. Turn the ignition on, then back off: (The H1/9 YELLOW wire must
be connected.)
3. Select a Menu. Press and HOLD the Valet/Program switch: (The
Valet/Program switch must be plugged into the blue port.) After three seconds
the siren will chirp once indicating entry to the Basic Features Menu #1. If this
is the menu you wish to access, release the button and go on to Step 4. If the
button is not released, you will jump to the Advanced Features Menu #2 and
the siren will chirp twice. Once you have selected the desired menu, release the
Valet/Program button and then proceed to Step 4.
4. Select a Feature. Press and release the Valet/Program switch the number of
times corresponding to the feature you wish to change. For example, to access
the third feature, press and release the switch three times. Then press the switch
once more and HOLD it. The siren will chirp the number of times equal to
the step you have accessed.
5. Program the Feature. While HOLDING the Valet/Program switch, you can
toggle the feature on and off using the remote transmitter. Pressing
will
select the one chirp setting. Pressing
will select the two chirp
setting. (See System Features Menus section of this guide.)
NOTE: The Valet pulse count feature (2-5) and the Channel three timed
output (2-9) have five possible settings each. Pressing
will toggle through
all the two-chirp settings.
6. Release the Valet/Program Switch.
Once a feature is programmed:
➤ Other features can be programmed within the same menu.
➤ Another menu can be selected.
➤ The learn routine can be exited if programming is complete.
©
2003 Directed Electronics, Inc.
15
To access another feature in the same menu:
1. Press and release the Valet/Program switch the number of times necessary to advance from the
feature you just programmed to the next one you want to program.
2. Then press the Valet/Program switch once more and HOLD it.
For example, if you just programmed the third feature in the menu and you would like to program
the seventh feature in the menu, you would press and release the Valet/Program switch four times
and then press it once more and hold it. The siren would chirp seven times to confirm access to the
seventh feature.
To select another menu:
1. Press and HOLD the Valet/Program switch.
2. After three seconds, the unit will advance to the next menu and the siren will chirp, indicating
which menu has been accessed.
For instance, if you just programmed some features in Menu #1 (Basic Features) and you wish to
program a feature in Menu #2, you press and hold the Valet/Program button. After three seconds,
the siren chirps twice indicating access to Menu #2.
To exit the learn routine do one of the following:
➤ Close the open door.
➤ Turn the ignition on.
➤ No activity for longer than 15 seconds.
➤ Press the Valet/Program switch too many times.
16
©
2003 Directed Electronics, Inc.
System Features Menus
Menu #1 - Basic Features
Items in bold text have been programmed to the default setting at the factory.
Feature
Number
One Chirp
Setting
Two-Chirp
Setting
1-1
Active arming
Passive arming
1-2
Chirps ON
Chirps OFF
1-3
Ignition controlled door locks ON
Ignition controlled door locks OFF
1-4
Active locking only
Passive locking
1-5
Panic with ignition on
No panic with ignition on
1-6
0.8 second door lock pulses
3.5 second door lock pulses
1-7
Forced passive arming ON
Forced passive arming OFF
1-8
Automatic Engine Disable ON
Automatic Engine Disable OFF
1-9
Armed When Driving (AWD)
Vehicle Recovery System (VRS)
1-10
Code Hopping™ on
Code Hopping™ off
Menu #2 - Advanced Features
Feature
Number
One Chirp
Setting
Two-Chirp
Setting
2-1
Siren
Horn honk
2-2
30-second siren duration
60-second siren duration
2-3
Nuisance Prevention® Circuitry on
Nuisance Prevention® Circuitry off
2-4
Progressive door trigger
Instant door trigger
2-5
Valet switch input: 1 pulse
Valet switch input: 2-5 pulses
2-6
Bypass Notification ON
Bypass Notification OFF
2-7
Ignition-controlled domelight ON
Ignition-controlled domelight OFF
2-8
Single unlock pulse
Double unlock pulse
2-9
Channel 3: Validity
Channel 3: latched/latched, reset
with ignition/30-second timed/
second unlock output*
*Second unlock is only available if Feature 2-8 is programmed to single pulse.
©
2003 Directed Electronics, Inc.
17
Feature Descriptions
The features of the system are described below. Features that have additional settings that can be
selected only when programming with the 998T Bitwriter are indicated by the following
icon:
Menu #1 - Basic Features
1-1 ACTIVE/PASSIVE ARMING: When active arming is selected, the system will only arm when
the transmitter is used. When set to passive, the system will arm automatically 30 seconds after the
last door is closed. To alert the consumer of passive arming, the siren will chirp 20 seconds after the
door is closed. This provides the consumer with an audible indication prior to the system actually
arming. At the 30 second mark, the system will arm but the siren will not chirp.
1-2 CHIRPS ON/OFF: This feature controls the chirps that confirm the arming and disarming of
the system.
1-3 IGNITION CONTROLLED DOOR LOCKS ON/OFF: When turned on, the doors will
lock three seconds after the ignition is turned on and unlock when the ignition is turned off.
The 998T Bitwriter will display separate steps for ignition lock and ignition unlock. They can be
programmed on or off independently.
1-4 ACTIVE/PASSIVE LOCKING: If passive arming is selected in step 1-1, then the system can be
programmed to either lock the doors when passive arming occurs, or only lock the doors when the
system is armed via the transmitter. Active locking means the system will not lock the doors when
it passively arms. Passive locking means that the system will lock the doors when it passively arms.
NOTE: Remember, when passive arming is selected, the unit will chirp 20 seconds after the last
door is closed. The system does not actually arm or lock the doors until 30 seconds after the door
has been closed.
1-5 PANIC WITH IGNITION ON: This step controls whether or not the Panic Mode is available
with the ignition on. In some states, there are laws prohibiting a siren from sounding in a moving
vehicle. This feature makes the system compliant with these regulations.
1-6 DOOR LOCK PULSE DURATION: Some European vehicles, such as Mercedes-Benz and
Audi, require longer lock and unlock pulses to operate the vacuum pump. Programming the system
to provide 3.5 second pulses, will accommodate the door lock interface in these vehicles. The default
setting is 0.8 second door lock pulses.
18
©
2003 Directed Electronics, Inc.
1-7 FORCED PASSIVE ARMING ON/OFF: To use this feature, passive arming must be selected in
step 1-1. When turned on, forced passive arming will ensure that the system will passively arm, even
if a zone is left open or invalid. Forced passive arming occurs one hour after the ignition is turned
off.
1-8 AUTOMATIC ENGINE DISABLE (AED) ON/OFF: AED is a full-time, passive starter disable
that works independently of the security system. When turned on, the orange, ground-when-armed
output (H1/1) will go active 30 seconds after the ignition is turned off. The LED will flash at half
its normal rate when the ignition is turned off to indicate that AED is active and will interrupt the
starter in 30 seconds. AED does not occur in Valet mode and can be bypassed using the emergency
override procedure. The transmitter can also be used to disarm AED.
1-9 ARMED WHILE DRIVING/VEHICLE RECOVERY SYSTEM: In the default setting (Armed
While Driving), the system can be armed with the ignition on. When armed, the ground-whenarmed is not active and the sensors are bypassed. The door triggers will remain active. If
programmed to the Vehicle Recovery System (VRS®) setting, VRS® will be activated.
1-10 CODE-HOPPING™ ON/OFF: The system uses a mathematical formula to change its code
each time the transmitter and receiver communicate. This makes the group of bits or “word” from
the transmitter very long. The longer the word is, the easier it is to block its transmission to the unit.
Disabling the Code-Hopping™ feature lets the receiver ignore the Code-Hopping™ part of the
transmitted word. As a result, the unit may have better range with Code-Hopping™ off.
Menu #2 - Advanced Features
2-1 SIREN/HORN HONK: The system can be programmed to output pulses instead of a
continuous output when the system is triggered. This is useful to honk the factory horn in applications where a siren is undesirable. Remember that the unit is only capable of supplying 1 amp of
current. A relay will be required to interface with most factory horn systems.
2-2 SIREN DURATION 30/60 SECONDS: It is possible to program the unit to sound for 30
or 60 seconds during the triggered sequence. Some states have laws regulating how long a
security system can sound. When using the 998T Bitwriter, the siren can be programmed to sound for
any length of time ranging from 1 to 180 seconds. Using the SELECT button of the 998T Bitwriter
will adjust the siren duration in one second increments.
2-3 NUISANCE PREVENTION® CIRCUITRY (NPC®) ON/OFF: NPC® stops repeated triggering
of the same zone. If one zone is triggered three times in one hour, that zone is bypassed for one hour,
starting from the time of the third trigger. During that hour, if the system detects a trigger on that
©
2003 Directed Electronics, Inc.
19
zone again, the system resets the one hour timer. If one hour passes and the zone has not triggered
again, the zone is activated and can trigger the system again. NPC® monitors sensor inputs and the
door trigger, but does not bypass the ignition trigger at any time. If NPC® is turned off, the system
will respond to repeated triggers on the sensor inputs and will do so indefinitely. Some states have
laws regulating how many times a security system can trigger before it is considered a nuisance and
the vehicle is towed away.
2-4 PROGRESSIVE DOOR TRIGGER ON/OFF: The system responds to a door trigger input with
a progressive response. When the door is opened with the system armed, the siren will chirp 10
times prior to the full triggered sequence. The door trigger is still treated as an instant trigger and
closing the door quickly will not prevent a full triggered sequence from occurring. If the progressive
door trigger is programmed off, the full siren output will occur the moment the door is opened.
2-5 VALET PULSE COUNT ONE TO FIVE PULSES: The system can be programmed to count
the number presses of the valet button before disarming the security system or VRS®. The factory
default setting is one pulse. The unit can be set for two to five pulses using the two-chirp setting to
select the pulse count.
Ghost Switch Option: For added security, the GRAY wire on the two-pin Valet/Program can be
connected to any switch in the vehicle that provides a positive (+) momentary pulse.
2-6 BYPASS NOTIFICATION ON/OFF: when programmed on, any active zone input to the
system during arming will generate a bypass notification chirp. When programmed OFF, no bypass
notification chirps will be generated if any zone is active during arming.
2-7 IGNITION-CONTROLLED DOMELIGHT SUPERVISION ON/OFF: If turned on, the
system will turn on the domelight for 30 seconds when the ignition is turned off. The optional
domelight supervision feature must be installed.
2-8 DOUBLE PULSE UNLOCK ON/OFF: Some vehicles require two pulses on a single wire to
unlock the doors. When the double pulse unlock feature is turned on, the BLUE H2/C wire will
supply two negative pulses instead of a single pulse. At the same time, the GREEN H2/A wire will
supply two positive pulses instead of a single pulse. This makes it possible to directly interface with
double pulse vehicles without any extra parts.
2-9 CHANNEL 3 VALIDITY/LATCHED/LATCHED RESET WITH IGNITION/30 SECOND
TIMED/SECOND UNLOCK OUTPUT: Channel 3 can be programmed for these output configurations. The unit is set to the default validity output. To change the configuration, use the two-chirp
setting to toggle to the different configurations.
20
©
2003 Directed Electronics, Inc.
Transmitter/Receiver Learn Routine
NOTE: For information regarding transmitter programming please refer to the Owner’s Guide.
The system comes with two transmitters that have been taught to it. The system can store up to
four different transmitter codes in memory. Use the following learn routine to add transmitters to
the system or to change button assignments if desired.
If the system was previously programmed using the 998T Bitwriter, the learn routine may be locked.
If the siren generates one long chirp when attempting to program the unit, the learn routine is locked
and must be unlocked using the 998T Bitwriter before proceeding.
1. Open a door. (The GREEN wire, H1/5, or the VIOLET, H1/7 must be
connected.)
2. Turn the ignition on. (The YELLOW wire, H1/9 must be connected.)
3. Select the receiver channel: Press and release the Valet/Program button the
number of times necessary to access the desired channel.
NOTE: If adding a remote, a button must be taught to the unit in the Channel 1 or Channel 4
position prior to programming other channels.
Press and hold the Valet/Program button once more. The siren will chirp and the LED will blink
the number of times corresponding to the channel that is accessed.
Channel Number
Function
Wire Color
1
Arm/Disarm/Panic
2
Silent Mode/Remote Valet/Trunk Release
RED/WHITE
3
Remote Start or other accessories
WHITE/BLUE
4
Arm only
5
Disarm only
6
Panic only
7
Auto-learn Standard Configuration*
8
Auto-learn Single Button Arm/Disarm Configuration*
9
Delete all transmitters
*NOTE: For Auto Learn Configurations, see Transmitter Configurations section of this guide.
©
2003 Directed Electronics, Inc.
21
4. Press the transmitter button: While holding the Valet/Program button, press
the button from the transmitter that you wish to assign to the selected channel.
The unit will chirp indicating successful programming. It is not possible to
teach a transmitter button to the system more than once.
Channels #4-6: Channels 4 through 6 are used to assign the arm, disarm and panic functions to
separate buttons on the remote control. Teaching a button to Channel 4 erases all information about
that remote from memory. Any auxiliary functions that are desired will have to be reprogrammed.
Similarly, if the remote is set up to use the separate arm, disarm and panic channels and a button
from that remote is entered into channel one, the remote will be erased from memory, and the system
will only recognize the button that was entered into channel one.
Channel #9: If any button from a known transmitter is programmed to Channel 9, all transmitters
will be erased from memory and the system features will revert to the default settings. This is useful
in cases where the one of the customer's transmitters is lost or stolen. This will erase any lost or
stolen transmitters from the system's memory. It can also be used to start from scratch if the transmitter buttons were programmed incorrectly.
5. Release. Once the code is learned, the Valet/Program button can be released.
To exit the learn routine:
One long chirp indicates that Learn Routine has been exited. Learn Routine will be exited if any of
the following occurs:
➤
➤
➤
➤
22
Ignition is turned off.
Door is closed.
Valet/Program button is pressed too many times.
More than 15 seconds elapse between steps.
©
2003 Directed Electronics, Inc.
Transmitter Configurations
The transmitters can be programmed with the standard or single button arm/disarm configurations
by using the Auto Learn functions in the Transmitter/Receiver Learn Routine.
Standard Configuration
A transmitter/receiver that uses the standard configuration operates similarly to many factory
keyless entry remotes. A standard configuration transmitter allows arming, disarming, and Panic
Mode activation with separate buttons. When programmed for standard configuration, the transmitter buttons are assigned to the following functions:
and
operates
Arm only
operates
Disarm only
operates
Channel 2 and Silent Mode
operates
Panic only
operate
Channel 3
The standard configuration also allows the user to utilize Multi-Level Security Arming, a feature
that cannot be accessed from a single button arm/disarm configuration transmitter.
Single Button Arm/Disarm Configuration
When programmed for single button arm/disarm configuration, the transmitter buttons are
assigned to the following functions:
©
2003 Directed Electronics, Inc.
operates
Arm/Disarm/Panic
operates
Channel 2 and Silent Mode
operates
Channel 3
23
Diagnostics
The system’s microprocessor monitors and reports all active and violated zones when arming and
disarming. LED flashes indicate the active or violated zone; siren chirps indicate system status.
Arm/Disarm Diagnostics
The number of siren chirps will indicate the status of the system when arming and disarming. For
information on which zone is active or has been violated refer to the Table of Zones.
System Status Chirps
Action
Number of Chirps
Description
Arm
1
System armed
Arm
1 (3 second delay), 1
System armed with Bypass Notification
Disarm
2
System disarmed
Disarm
4
System disarmed with Tamper Alert
Disarm
5
System disarmed NPC® active
Table of Zones
Zone No.
Trigger type
Input description
1
Instant
H1/6 BLUE wire. Connect to optional hood/trunk
pins.
2
Multiplexed
BLUE wire of plug-in shock sensor. Inputs
shorter than 0.8 seconds will trigger a Warning
Zone response, while inputs longer than 0.8
seconds will instantly trigger the full alarm
sequence.
3
Two-stage, progresses from
warning to full alarm
Door switch circuit. H1/5 GREEN or H1/7 VIOLET.
4
Multiplexed Input
GREEN wire of plug-in shock sensor. Inputs
shorter than 0.8 seconds will trigger a Warning
Zone response, while inputs longer than 0.8
seconds will instantly trigger the full alarm
sequence.
5
Two-stage (similar to doors)
Ignition input. H1/9 YELLOW.
NOTE: The Warn Away® response does not report on the LED.
24
©
2003 Directed Electronics, Inc.
Long Term Event History
The system stores the last two full triggers in memory. These are not erasable. Each time the unit
sees a full trigger, the older of the two triggers in memory will be replaced by the new trigger. To
access long term event history:
1.
With the ignition off, press and HOLD the Valet/Program switch.
2.
Turn on the ignition.
3. Release the Valet/Program switch.
4. Press and release the Valet/Program switch within five seconds. The LED will
flash in groups indicating the last two zones that triggered the unit. The LED
will flash for one minute or until the ignition is turned off.
NOTE: The Warning Zone triggers are not stored to memory and will not be reported.
Multi-Level Security Arming
Multi-Level Security arming allows the operator to select which inputs and sensors are active during
a particular arming cycle. For a full description of Multi-Level Security Arming operation for testing
purposes refer to the Owner's Guide.
Optional Vehicle Recovery System (VRS)
VRS is an optional feature designed to disable a vehicle during a carjacking event. It must be
programmed in the features menu and the Failsafe Starter Kill must be installed for it to work
properly. For operational instructions when testing VRS refer to the Owner's Guide.
©
2003 Directed Electronics, Inc.
25
Nuisance Prevention® Circuitry
Nuisance Prevention Circuitry bypasses any zone that triggers the system more than three times
within a one-hour period. For a full description of NPC operations refer to the Owner's Guide.
IMPORTANT: When testing the systems sensor and trigger inputs reset NPC by
turning on the ignition after every third system trigger.
Rapid Resume Logic
Rapid Resume Logic ensures that the when the system is powered up it will return to the same state
it was in when power is disconnected. For a full description of Rapid Resume Logic refer to the
Owner's Guide.
Troubleshooting
Starter kill doesn’t work.
➤
Is the correct starter wire being interrupted? If the car starts when the starter kill relay is
completely disconnected, the wrong starter wire has been cut and interrupted.
➤
YELLOW wire is not connected to true ignition. It is connected to an accessory circuit.
Shock sensor doesn’t trigger the alarm.
➤
Has the NPC® system been triggered? If so, you will hear five chirps when disarming. To check
this, turn the ignition key on and off to clear the NPC® from memory, and then retest the
shock sensor. For a detailed description of NPC®, see Owner’s Guide.
Door input does not immediately trigger full alarm. Instead, I hear chirps for the first three seconds.
➤
That’s how the progressive two-stage door input works! This is the instant response feature of
this system. Even if the door is closed immediately, the system provides an instant trigger by
chirping, and the progressing to a constant siren.
Closing the door triggers the system, but opening the door does not.
➤
Have you correctly identified the type of door switch system? This happens often when the
wrong door input has been used.
26
©
2003 Directed Electronics, Inc.
System will not passively arm until it is remotely armed and then disarmed.
➤
Are the door inputs connected? Is a blue wire connected to the door trigger wire in the vehicle?
Either the green H1/5 or the violet H1/7 should be used instead.
Door input does not respond with the progressive trigger, but with immediate full alarm.
➤
What zone does the LED indicate? If the LED indicates that the impact sensor caused the
trigger, the sensor may be detecting the door opening. Reducing the sensitivity or relocating
the sensor can often solve this problem. If the LED indicates that the door caused the trigger,
you may have programmed the progressive door trigger off. (See Feature 2-4 in the Feature
Descriptions section of this guide.)
The Valet button doesn’t work.
➤
Is it plugged into the correct socket? Check the System Features Learn Routine for the
programmed Valet pulse count.
Status LED doesn’t work.
➤
Make sure that it is plugged in. (See Plug-In Harnesses section of this guide.) Is the LED
plugged into the correct socket?
©
2003 Directed Electronics, Inc.
27
Wiring Quick Reference Guide
28
©
2003 Directed Electronics, Inc.