321035A5 Glowster Pager - Diversified Electronic Applications

Pager and Charger Guide
Part Number 321035A5
Premises Pager System®
®
Glowster Pagers
Introduction
Introduction:
Congratulations on your purchase of a JTECH Paging System. Please take a
few minutes to review this manual prior to installing and operating your
system.
Please inspect the System upon receipt. If the contents appear to be
damaged, notify the shipper immediately to file a claim and notify JTECH
Customer Care. If components are missing, contact JTECH Customer Care.
If you have any questions or need assistance, please call JTECH Customer
Care at 800-321-6221 or 561-997-0772, option 6.
Components
Glowster
Pager
Glowster
Pager with
Optional
Promotional Back
and Inserts
AC Power
Cord
2.4 A or
Optional
7.3A
Power
Adapter
Quad
Charger
Single
Charger
Glowster Pager System
Components:
Jumpers
(Optional Equipment)
Chargers
Multiple Chargers:
• A single Charger can hold up to 15 Pagers.
• If two, three or four Single Chargers are to be used, they can be
combined and powered with the 2.4A Power Adapter (standard).
• If two or three Quad Chargers are to be used, they can be combined and
powered with the 7.3A Power Adapter (optional).
• Use the Jumpers (optional) to connect Chargers together.
Jumper
Bottom view
of Charger
2
•
Chargers can be placed on table or counter
tops.
Chargers must be placed on a level surface to
properly stack Pagers.
Power
Adapter
Plug
Connect Power:
Charger
Jack
1. Insert the Power Adapter plug into
the Charger jack at the bottom of
the Charger.
2. Connect the Power Adapter to the
Power Cord.
Charging
Rack
3. Plug the Power Cord into a 120VAC outlet.
Adapter
Power Cord
120VAC
Outlet
Connect Power
•
Mount Chargers
Mount Chargers:
4. Once the Charger is ON, the Pagers can be stacked.
3
•
•
•
Pagers are turned OFF for shipment from JTECH.
When first received, Pagers are to be charged for a minimum of 8 hours
prior to use.
This first charge will also turn ON the Pagers.
1. Stack the Pagers onto the Charger locations.
2. Stack a maximum of 15 Pagers high per any charging location.
3. Once place into the powered (ON) Charger, each Pager’s LED will
light.
4. While on the Charger, the LED indicates charging condition.
• Double Flashing red light = Battery charge very low. Charge
Needed. Do not use the Pager.
• Solid red light = OK to use.
• When removed from the Charger, the flashing LED indicates the
Pager is ready for use.
Charging Lights
Charge Pagers
Charge Pagers:
•
•
Pagers in use and returned to the Charger within 24
hours will fully charge within 12 hours.
If not returned within 24 hours, charging time of up
to 24 hours may be required to fully charge
batteries.
F
E
Store Pagers
Store Pagers:
4
•
•
•
Store Pagers in the Charger when not in use.
To maintain maximum battery capacity, store Pagers
in the powered (ON) Charger.
If not recharged in 3-6 months, Pager batteries may
become damaged beyond repair and will need to be
replaced.
F
E
2.
3.
4.
5.
6.
7.
•
Remove the Pager you wish to page
from the Charger.
The Pager will flash and vibrate to
confirm it is ready for use.
The Pager LED in the front of the Pager
will continue to flash every 3-4 seconds
to confirm the Pager is ON and ready to
accept a page.
Enter the number of the Pager you wish
to page on the Transmitter or Remote
Keypad.
Press # to send the page.
The XMIT light on the Transmitter will
turn ON, confirming the page is being
sent. If using a Remote Keypad, the
Keypad XMIT light does not ON.
The Pager will vibrate, flash tone or
speak as required.
See “Enter Pager #” Menu Functions in
your Transmitter manual for more
information.
Paging Using a 8205 & 8214 SmartAlert with RS232 and Telephone
Transmitter:
•
See Paging instructions in your Transmitter
manual for more information.
SmartAlert Paging
1.
Desktop Paging
Paging Using a Desktop Transmitter:
5
1. Batteries that no longer charge properly or have a reduced operating
time can be replaced by the user.
2. Turn the Pager over.
3. Use a #2 Philips screwdriver to remove the screw.
4. Remove the battery door.
5. Remove the battery pack.
6. Unplug the battery connector.
7. Dispose of the Nickel Metal Hydride battery pack at any retail
department or home improvement stores that recycles batteries.
8. Plug the new battery into the Pager’s connector.
9. Place the battery into the bottom of the Pager compartment.
10. Replace the battery door and screw (do not over tighten).
11. Place the Pager on the Charger and fully
charge the battery.
Lo
os
en
Replace the Battery
Replace the Battery:
Tig
n
hte
6
1.
2.
3.
4.
5.
Turn the Pager over.
Use a #2 Philips screwdriver to remove the screw.
Press on the back of the Promotional Back and twist to remove.
Replace with new Promotional Back.
Replace and tighten the screw (do not over tighten).
Press here to
unlock and then
twist.
Lo
os
en
Replace the Promotional Back
Replace the Promotional Back:
Tig
n
hte
Replace the Insert:
2.
3.
4.
5.
6.
Use a flat blade screwdriver or equivalent to pry up the clear plastic
cover.
Slide the clear plastic cover out.
Remove the Insert.
Replace with a new Insert.
Slide the clear plastic cover back into place.
When complete inserted, the cover will “snap” into place.
Replace the Insert
1.
JTE
CH
JTE
CH
Inserts:
•
•
Inserts can be made by the user or professionally printed (call your
JTECH sales representative for more details).
Material thickness is 0.020” (5.1mm) maximum.
Insert
Dimensions
Insert Dimensions
JTE
CH
3-3/8” (85.7mm)
1-5/8” (41.3mm)
7
SYSTEM WARRANTY
JTECH Communications, Inc. warrants its equipment to be free from defects
in materials and workmanship for a period of one year. Its obligation under
this warranty is limited to repairing or replacing, at its own sole option, any
such defective products. Products must be returned with transportation
charges prepaid and must be accompanied by a brief description of the
problem encountered and date and place of purchase. This warranty does
not apply to equipment which has been damaged by accident, negligence or
misapplication or has been altered or modified in any way. This warranty
applies only to the original purchaser who must have properly registered the
product within ten days of purchase.
The following are not covered under our one-year warranty: adapters,
antennas, user-replaceable batteries, pager belt clips, pager promobacks,
pager battery doors, pager neck chains, liquid damage to master transmitter,
pagers or chargers, lightning strikes or other acts of God that could affect the
performance of the master transmitter, pagers and peripherals.
6413 Congress Avenue
Suite 150
Boca Raton, Florida 33487
800-321-6221
Part Number 321035A5
© 2008, JTECH Communications, Inc. All Rights Reserved.
8
Download PDF

advertising