Interlogix IFS Wireless Access Points WMC251-1W-2T-150 User manual
Advertisement
Advertisement
IFS WMC251-1W-2T-150
User Manual
P/N 1073051 • REV A • ISS 15OCT15
I
Copyright © 2015 United Technologies Corporation
Interlogix is part of UTC Building & Industrial Systems, Inc. a unit of United
Technologies Corporation. All rights reserved.
Trademarks and The WMC251 Series name and logo are trademarks of United Technologies. patents
Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
Manufacturer Interlogix
3211 Progress Drive, Lincolnton, NC 28092 USA
Authorized EU manufacturing representative:
UTC Climate Controls & Security B.V.,
Kelvinstraat 7, 6003 DH Weert, Netherlands
Intended use Use this product only for the purpose it was designed for; refer to the data sheet and user documentation for details. For the latest product information, contact your local supplier or visit us online at www.interlogix.com.
Certification
ACMA compliance Notice! This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
European Union 2004/108/EC (EMC Directive): Hereby, UTC Building & Industrial Systems, Inc.
directives declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense. Any changes or modifications not expressly approved by UTC could void the user’s authority to operate this equipment under the rules and regulations of the FCC.
FCC Caution:
To assure continued compliance, (for example, use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired operation.
II
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.
CAUTION: Changes or modifications not expressly approved by UTC for compliance could void the user’s authority to operate the equipment.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation. For energy saving, please remove the DC-plug to disconnect the device from the power circuit. Without removing the DC-plug, the device still consumes power from the power circuit. In view of Saving the Energy, it is strongly suggested to remove the DC-plug for the device if this device is not intended to be active.
Canadian Compliance
This Class B digital apparatus meets all requirements of the Canadian Interference Causing
Equipment Regulations. Cet appareil numérique de la classe B respects toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
Canada - Industry Canada (IC)
The wireless radio of this device complies with RSS 247 and RSS 102 of Industry Canada.
This Class B digital device complies with Canadian ICES-003 (NMB-003).
Cet appareil numérique de la classe B respects toutes les exigences du Règlement sur le matériel brouilleur du Canada.
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
WMC251-1W-2T-150 complies with IC requirements, IC: 20201-WMC251150.
III
This radio transmitter (IC: 20201-WMC251150) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Internal (Default): 12dBi directional antenna (Vertical-Polarity)
External (Option): RP-SMA (Female) type Connector
Le présent émetteur radio (IC: 20201-WMC251150) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur .
intégré 12dBi antenne double polarisation
External (Optional): RP-SMA (Female) type Connector
Digital Transmission Systems (DTSs)
DTSs include systems that employ digital modulation techniques resulting in spectral characteristics similar to direct sequence systems. The following applies to the bands 902-928 MHz and 2400-2483.5
MHz.
(1) The minimum 6 dB bandwidth shall be 500 kHz.
(2) The transmitter power spectral density conducted from the transmitter to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. This power spectral density shall be determined in accordance with the provisions of Section 5.4(4), (i.e. the power spectral density shall be determined using the same method as is used to determine the conducted output power).
For DTSs employing digital modulation techniques operating in the bands 902-928 MHz and
2400-2483.5 MHz, the maximum peak conducted output power shall not exceed 1W. Except as provided in Section 5.4(5), the e.i.r.p. shall not exceed 4 W.
As an alternative to a peak power measurement, compliance can be based on a measurement of the maximum conducted output power. The maximum conducted output power is the total transmit power delivered to all antennas and antenna elements, averaged across all symbols in the signalling alphabet when the transmitter is operating at its maximum power control level. Power must be summed across all antennas and antenna elements. The average must not include any time intervals during which the transmitter is off or transmitting at a reduced power level. If multiple modes of operation are implemented, the maximum conducted output power is the highest total transmit power occurring in any mode.
(5) Fixed point-to-point systems in the bands 2400-2483.5 MHz and 5725-5850 MHz are permitted to have an e.i.r.p. higher than 4 W provided that the higher e.i.r.p. is achieved by employing higher gain directional antennas and not higher transmitter output powers. Point-to-multipoint systems,2
IV
omnidirectional applications and multiple co-located transmitters transmitting the same information are prohibited from exceeding an e.i.r.p. of 4 W.
(6) Transmitters may operate in the band 2400-2483.5 MHz, employing antenna systems that emit multiple directional beams simultaneously or sequentially, for the purpose of directing signals to individual receivers or to groups of receivers, provided that the emissions comply with the following:
(i) Different information must be transmitted to each receiver.
(ii) If the transmitter employs an antenna system that emits multiple directional beams, but does not emit multiple directional beams simultaneously, the total output power conducted to the array or arrays that comprise the device (i.e. the sum of the power supplied to all antennas, antenna elements, staves, etc., and summed across all carriers or frequency channels) shall not exceed the applicable output power limit specified in sections 5.4(2) and 5.4(4). However, the total conducted output power shall be reduced by 1 dB below the specified limits for each 3 dB that the directional gain of the antenna/antenna array exceeds 6 dBi. The directional antenna gain shall be computed as the sum of
10 log (number of array elements or staves) plus the directional gain of the element or stave having the highest gain.
(iii) If a transmitter employs an antenna that operates simultaneously on multiple directional beams using the same or different frequency channels, the power supplied to each emission beam is subject to the applicable power limit specified in sections 5.4(2) and 5.4(4). If transmitted beams overlap, the power shall be reduced to ensure that their aggregate power does not exceed the applicable limit specified in sections 5.4(2) and 5.4(4). In addition, the aggregate power transmitted simultaneously on all beams shall not exceed the applicable limit specified in sections 5.4(2) and 5.4(4) by more than 8 dB.
(iv) Transmitters that transmit a single directional beam shall operate under the provisions of sections
5.4(2), 5.4(4) and 5.4(5).
5.5 Unwanted Emissions
In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated device is operating, the RF power that is produced shall be at least 20 dB below that in the
100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided that the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of root-mean-square averaging over a time interval, as permitted under Section
5.4(4), the attenuation required shall be 30 dB instead of 20 dB. Attenuation below the general field strength limits specified in RSS-Gen is not required.
The measurement procedure defined in Annex A of RSS-247 shall be used to verify the compliance to the e.i.r.p. at different elevations.
No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation or adaptation) without written permission from UTC
Fire and Security.
UTC, reserves the right to revise this publication and to make changes in content from time to time
V
without obligation on the part of UTC to provide notification of such revision or change. UTC provides this guide without warranty of any kind, implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. UTC may make improvements or changes in the product(s) described in this manual at any time.
CAUTION: TO ENSURE REGULATORY COMPLIANCE, USE ONLY THE PROVIDED POWER AND
INTERFACE CABLES.
CAUTION: DO NOT OPEN THE UNIT. DO NOT PERFORM ANY SERVICING OTHER THAN THAT
CONTAINED IN THE INSTALLATION AND TROUBLESHOOTING INSTRUCTIONS. REFER ALL
SERVICING TO QUALIFIED SERVICE PERSONNEL.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and
Satellite Earth Station Equipment) as of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
Wireless LAN and your Health
The WMC251-1W-2T-150 like other radio devices, emits radio frequency electromagnetic energy, but operates within the guidelines found in radio frequency safety standards and recommendations.
Restrictions on Use of Wireless Devices
In some situations or environments, the use of wireless devices may be restricted by the proprietor of the building or responsible representatives of the organization. For example, these situations may include:
Using wireless equipment in any environment where the risk of interference to other devices or services is perceived or identified as harmful.
If you are uncertain of the applicable policy for the use of wireless equipment in a specific organization or environment, you are encouraged to ask for authorization to use the device prior to turning on the equipment.
The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this product, or the substitution or attachment of connecting
VI
cables and equipment other than specified by the manufacturer. Correction of interference caused by such unauthorized modification, substitution, or attachment is the responsibility of the user.
The manufacturer and its authorized resellers or distributors are not liable for any damage or violation of government regulations that may arise from failing to comply with these guideline documentation that comes with the product.
Postpone router installation until there is no risk of thunderstorm or lightning activity in the area.
Do not overload outlets or extension cords, as this can result in a risk of fire or electric shock.
Overloaded AC outlets, extension cords, frayed power cords, damaged or cracked wire insulation, and broken plugs are dangerous. They may result in a shock or fire hazard.
Route power supply cords so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords where they are attached to plugs and convenience receptacles, and examine the point where they exit from the product.
Place this equipment in a location that is close enough to an electrical outlet to accommodate the length of the power cord.
Place this equipment on a stable surface.
When using this device, basic safety precautions should always be followed to reduce the risk of fire,
electric shock and injury to persons, including the following:
. Read all of the instructions {listed here and/or in the user manual} before you operate this equipment.
Give particular attention to all safety precautions.
Retain the instructions for future reference.
. Comply with all warning and caution statements in the instructions. Observe all warning and caution symbols that are affixed to this equipment.
. Comply with all instructions that accompany this equipment.
. Avoid using this product during an electrical storm. There may be a risk of electric shock from lightning. For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet, and disconnect the cable system.
This will prevent damage to the product due to lightning and power surges. We also recommend the use of ESP300 20Kv protection on the input at the switch or network.
. Operate this product only from the type of power source indicated on the product’s marking label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.
. Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe operating condition.
It is recommended that the customer install an AC surge protector in the AC outlet to which this device is connected. This is to avoid damaging the equipment by local lightning strikes and other electrical surges.
Different types of cord sets may be used for connections to the main supply circuit. Use only a main
line cord that complies with all applicable product safety requirements of the country of use. Installation
VII
of this product must be in accordance with national wiring codes.
Place unit to allow for easy access when disconnecting the power cord/adapter of the device from the
AC wall outlet.
Wipe the unit with a clean, dry cloth. Never use cleaning fluid or similar chemicals. Do not spray cleaners directly on the unit or use forced air to remove dust.
This product was qualified under test conditions that included the use of the supplied cables between system components. To be in compliance with regulations, the user must use these cables and install them properly. Connect the unit to a grounding type AC wall outlet using the power adapter supplied with the unit.
Do not cover the device, or block the airflow to the device with any other objects. Keep the device away from excessive heat and humidity and keep the device free from vibration and dust.
Installation must at all times conform to local regulations
National Restrictions
This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country
Bulgaria
France
Italy
Luxembourg
Norway
Restriction Reasons/remarks
None
General authorization required for outdoor use and public service
Outdoor use; limited to 10 Military Radiolocation use. Reframing of the 2.4 GHz mW e.i.r.p. within the band band has been ongoing in recent years to allow current
2454-2483.5 MHz relaxed regulation. Full implementation planned 2012
None
None
Implemented
None
If used outside of own premises, general authorization is required
General authorization required for network and service supply(not for spectrum)
This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund
Only for indoor applications Russian
Federation
Note: Please don’t use the product outdoors in France.
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.
VIII
Contact Information For contact information, see www.interlogix.com
or www.utcfssecurityproducts.eu
.
CONTENTS
IX
Figures
................................................................................................. 23
.......................................................................... 37
X
............................................................................. 54
F IGURE 5-42 S ECURITY S ETTINGS – 802.1
X A UTHENTICATION .................................................................. 58
...................................................................... 92
XI
....................................................................................... 99
XII
Chapter 1. Product Introduction
1.1 Package Contents
Thank you for choosing IFS WMC251-1W-2T-150. Before installing the AP, please verify the contents inside the package box.
WMC251-1W-2T-150 Quick Guide Plastic Strap
PoE Injector Power Adapter
If there is any item missing or damaged, please contact the seller immediately.
-1-
1.2 Product Description
Cost-effective and Flexible Wireless Solution
IFS WMC251-1W-2T-150 is compatible with IEEE 802.11b/g/n standard and supports a data rate of up to
150Mbps in 802.11n mode. The WMC251-1W-2T-150 not only has a built-in 12dBi panel antenna but also reserves one RP-SMA type antenna connector to allow versatile antenna installations including omnidirectional, yagi, sector, flat-panel and grid antennas. Furthermore, the WMC251-1W-2T-150 can directly communicate with the wireless IP cameras by using the popular 2.4GHz frequency band, thus turning the surveillance services into a wireless environment.
-2-
Multiple Operation Modes Designed for Various Applications
The WMC251-150 supports as many as 8 wireless operation modes including AP Bridge, AP Router, Client
Bridge, Client Router (WISP), WDS PtP, WDS PtMP, Repeater and Universal Repeater, thus meeting users’ various application requirements.
Advanced Security and Rigorous Authentication
The WMC251-150 supports WEP, WPA / WPA2, WPA-PSK and WPA2-PSK wireless encryptions, the advanced
WPA2-AES mechanism, and 802.1 X RADIUS authentications, which can effectively prevent eavesdropping from unauthorized users or stop an unauthenticated wireless access to bandwidth. Users are granted or denied access to the wireless LAN network based on the ACL (Access Control List) that the administrator pre-established. In addition, with the multiple-SSID feature, you can set up different wireless networks. The
WMC251-150 can therefore serve as a virtual access point for segmented networks tailored to any industrial need.
Rugged Architecture Provides Reliable Outdoor Connection
The WMC251-150 is equipped with a sturdy and durable housing, meeting the IP55 rating for outdoor usage, which is definitely suitable for harsh environments. Besides, with its UV-resistant feature, the surface of the
WMC251-150's lightweight plastic housing does not yield to brittle fracture easily. Thus, it is as reliable as the metal case but more economical. With the proprietary Power over Ethernet (PoE) design, the
WMC251-1W-2T-150 can be easily installed in the areas where power outlets are not available. Additionally, the reset button on the PoE injector brings convenience to the administrator who can remotely recover the system’s original setting and the self-healing (schedule reboot) capability to keep connection alive all the time.
Easy Deployment and Management
With user-friendly Web UI and step-by-step setup wizard, the WMC251-150 is easy to install, even for users who never experience in setting up a wireless network.
-3-
1.3 Product Features
Industrial Compliant Wireless LAN and LAN
Compliant with IEEE 802.11n wireless technology capable of having a data rate of up to 150Mbps
Backward compatible with 802.11b/g standard
Equipped with 10/100Mbps RJ45 ports for LAN and WAN with auto MDI/ MDI-X supported
Fixed-network Broadband Router
Supports WAN connection types: Dynamic IP, static IP, PPPoE, PPTP and L2TP
Supports multiple sessions like IPSec, L2TP and PPTP VPN pass-through
Supports virtual server and DMZ for various networking applications
Supports DHCP server, UPnP and IFS DDNS
RF Interface Characteristics
Built-in 12dBi-directional antenna
High Output Power with multiply-adjustable transmit power control
Optional RP-SMA connector for flexible wireless deployment
Outdoor Environmental Characteristics
IP55-rated outdoor UV-resistant plastic enclosure
Passive PoE design
Reset button on PoE injector
Operating temperature: -20~70 degrees C
Multiple Operations and Wireless Modes
Multiple operation modes: Bridge, Gateway and WISP
Multiple wireless modes: AP Bridge, AP Router, Client Bridge, WDS PtP, WDS PtMP, Repeater,
Universal Repeater and Client Router (WISP)
Supports multiple-SSID to allow users to access different networks through a single AP
Supports WMM (Wi-Fi Multimedia) for better performance
Secure Network Connection
Supports software Wi-Fi Protected Setup (WPS)
Advanced security: 64/128-bit WEP, WPA / WPA2, WPA-PSK / WPA2-PSK (TKIP/AES) and
802.1X authentication
Supports NAT firewall features with SPI function to protect against DoS attacks
Supports IP / Protocol-based access control and MAC filtering
Easy Installation and Management
Web-based UI and Quick Setup Wizard for easy configuration
System status monitoring includes DHCP Client and System Log
-4-
1.4 Product Specifications
Product
WMC251-1W-2T-150
2.4GHz 802.11n Wireless Outdoor CPE AP/ Router
Hardware
Standard Support
Memory
PoE
IEEE 802.11b/g/n
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
32 Mbytes DDR SDRAM
4 Mbytes Flash
Passive PoE
Interface
Wireless IEEE 802.11b/g/n, 1T1R
PoE LAN (LAN 1): 1 x 10/100BASE-TX, auto-MDI/MDIX, passive PoE
LAN 2/ WAN: 1 x 10/100BASE-TX, auto-MDI/MDIX
Antenna
Internal (Default): 12dBi directional antenna
■ Horizontal: 30 degree
■ Vertical: 20 degree
External (Optional): RP-SMA type Connector
■ Switchable by Software
■ For External Antenna Mode, attach antenna before power on
Wireless RF Specifications
Wireless Technology
IEEE 802.11b/g
IEEE 802.11n
Data Rate
IEEE 802.11b: 1, 2, 5.5, 11Mbps
IEEE 802.11g: up to 54Mbps
IEEE 802.11n (20MHz): up to 72Mbps
IEEE 802.11n (40MHz): up to 150Mbps
Media Access Control CSMA/CA
Modulation
Frequency Band
Transmission/Emission type: OFDM
Data modulation type: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
2.412GHz ~ 2.484GHz
Operating Channel
America/ FCC: 2.414~2.462GHz (11 Channels)
Europe/ ETSI: 2.412~2.472GHz (13 Channels)
RF Output Power (Max.)
IEEE 802.11b: up to 26 ± 1dBm
IEEE 802.11g: up to 21 ± 1dBm
IEEE 802.11n: up to 17 ± 1dBm
Receiver Sensitivity
(dBm)
IEEE 802.11b: -97dBm
IEEE 802.11g: -90dBm
IEEE 802.11n: -90dBm
Output Power Control 5-level TX power control
Software Features
LAN Built-in DHCP server supporting static IP address distribution
-5-
WAN
VPN Passthrough
Operation Mode
Firewall
Wireless Mode
Max. SSID
Supports UPnP
Supports IGMP Proxy
Supports 802.1d STP (Spanning Tree)
Static IP
DHCP (Dynamic IP)
PPPoE
PPTP
L2TP
PPTP
L2TP
IPSec
IPv6
Gateway
Bridge
WISP
NAT firewall with SPI (Stateful Packet Inspection)
Built-in NAT server supporting virtual server and DMZ
Built-in firewall with port/ IP address/ MAC/ URL filtering
AP Bridge
AP Router
Client Bridge
Client Router (WISP)
WDS PtP
WDS PtMP
WDS Repeater
Universal Repeater (AP+Client)
Up to 5
Channel Width
Wireless Isolation
Encryption Type
20MHz / 40MHz
Enable to isolate each connected wireless client so that they cannot access mutually
64/128-bit WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X
Wireless Security
Wireless LAN ACL (Access Control List) filtering
Wireless MAC address filtering
Supports WPS (Wi-Fi Protected Setup )
Enable/Disable SSID Broadcast
Max. Wireless Clients 20
Max. WDS APs 8
Max. Wired Clients
WMM
253
Supports Wi-Fi multimedia
QoS
NTP
Supports Quality of Service for bandwidth control
Network Time Management
Self Healing
B/G Protection Mode
IAPP Roaming
Management
Supports Schedule Reboot
Supports protection mechanism to prevent collisions among 802.11b/g modes
Supports IAPP (Inter Access Point Protocol) roaming
Web UI, DHCP Client, Configuration Backup and Restore, Dynamic DNS
-6-
Diagnostic Tool
Mechanical and Power
System Log
IP Level
Weight
IP55
Material Outdoor UV-resistant enclosure
Dimensions (W x D x H) 127 x 63 x 254 mm
485g
Installation
Power Requirements
Pole mounting or wall mounting
LAN1
12V DC, 1A/ passive PoE
Pin 4 V DC+
Pin 5 reset
Pin 7, 8 V DC-
Power Consumption
(Max.)
4W
Environment and Certification
Operating Temperature -20~70 degrees C
Operating Humidity 10~95% non-condensing
Regulatory CE, FCC, RoHS
Accessory
Standard Accessories
WMC251-1W-2T-150 x 1
12V Power Adapter x 1
PoE Injector x 1
Plastic Strap x 1
Quick Installation Guide x 1
-7-
Chapter 2. Hardware Installation
Please follow the instructions below to connect WMC251-1W-2T-150 to the existing network devices and your computers.
2.1 Hardware Description
Dimensions: 127 x 63 x 254 mm (W x D x H)
Rear Panel – LED
Figure 2-1 Three-way View
Figure 2-2 LED
-8-
LED Definition
LED
Power
WLAN
LAN1
LAN2 (WAN)
Color State
Blue On
Blue Off
Blue On
Blue Off
Blue Blinking
Blue On
Blue Off
Blue Blinking
Meaning
System On
System Off
Wireless Radio On.
Wireless Radio Off.
Data is transmitting or receiving on the wireless.
Port linked.
No link.
Data is transmitting or receiving on the LAN interface.
Blue On
Blue Off
Port linked.
No link.
Blue Blinking Data is transmitting or receiving on the WAN interface.
Table 2-1 The LED Indication
2.1.1 The Bottom Panel – Port
The bottom panel provides the physical connectors connected to the power adapter and any other network device. Figure 2-3 shows the bottom panel of the WMC251-150.
Bottom Panel
Figure 2-3 Port and Connector of WMC251-150
-9-
PoE Injector
Figure 2-4 Port and Connector Description Label
Figure 2-5 PoE Injector of WMC251-150
Reset Button
Figure 2-6 Label of PoE Injector
H/W Interface Definition
Interface
RP-SMA Connector
Function
You can use the RP-SMA connector to connect with the 2.4GHz outdoor antenna.
※ For External Antenna Mode, you MUST physically attach antenna before powering on. Then, configure the Antenna Switch (Wireless Advanced page) from “Internal” to “External” via Web UI.
-10-
LAN (Passive PoE)
WAN
Reset
10/100Mbps RJ45 port, auto MDI/ MDI-X & passive PoE supported.
Connect LAN port to the PoE injector to power on the device.
PIN assignment:
Pin 4 VDC+
Pin 5 Reset
Pin 7, 8 VDC-
10/100Mbps RJ45 port, auto MDI/ MDI-X.
Connect this port to the xDSL modem in gateway mode.
Connect this port to the network equipment in bridge mode.
Push continually the reset button on the PoE injector about 10 seconds to reset the configuration parameters to factory defaults.
※ If you have connected with a lightning protector like IFS ESP300, please DO NOT press the reset button on the PoE injector to prevent the
ESP300 from being damaged. Remove the thunder protector before pushing the reset button.
Table 2-2 The PoE Injector Indication
-11-
Chapter 3. Connecting to the AP
3.1 Preparation before Installation
3.1.1 Professional Installation Required
Please seek assistance from a professional installer who is well trained in the RF installation and knowledgeable in the local regulations.
3.1.2 Safety Precautions
1. To keep you safe and install the hardware properly, please read and follow these safety precautions.
2. If you are installing the WMC251-150 for the first time, for your safety as well as others’, please seek assistance from a professional installer who has received safety training on the hazards involved.
3. Keep safety as well as performance in mind when selecting your installation site, especially where there are electric power and phone lines.
4. When installing the WMC251-150, please note the following things:
♦ Do not use a metal ladder;
♦ Do not work on a wet or windy day;
♦ Wear shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket.
5. When the system is operational, avoid standing directly in front of it. Strong RF fields are present when the transmitter is on.
3.2 Installation Precautions
Users MUST use a proper and well-installed surge arrestor and grounding kit with WMC251-150; otherwise, a random lightning could easily cause fatal damage to the WMC251-150. (Lightning
DAMAGE IS NOT COVERED UNDER WARRANTY).
Users MUST use the “PoE Injector” and “Power Adapter” shipped in the box with the WMC251-150.
Otherwise, the product might be damaged.
-12-
OUTDOOR INSTALLATION WARNING
!
IMPORTANT SAFETY PRECAUTIONS:
LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with the equipment you are installing.
CONTACTING POWER LINES CAN BE LETHAL. Make sure no power lines are anywhere where possible contact can be made. Antennas, masts, towers, guy wires or cables may lean or fall and contact these lines. People may be injured or killed if they are touching or holding any part of equipment when it contacts electric lines. Make sure that equipment or personnel do not come in contact directly or indirectly with power lines.
The horizontal distance from a tower, mast or antenna to the nearest power line should be at least twice the total length of the mast/antenna combination. This will ensure that the mast will not contact power if it falls either during installation or later.
TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.
Select equipment locations that will allow safe, simple equipment installation.
Don’t work alone. A friend or co-worker can save your life if an accident happens.
Use approved non-conducting lasers and other safety equipment. Make sure all equipment is in good repair.
If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.
If anything such as a wire or mast does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO
MOVE IT. Instead, save your life by calling the power company.
Don’t attempt to erect antennas or towers on windy days.
MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO
ANTENNAS HAVE LIGHTNING ARRESTORS. This will help prevent fire damage or human injury in case of lightning, static build-up, or short circuit within equipment connected to the antenna.
The base of the antenna mast or tower must be connected directly to the building protective ground or to one or more approved grounding rods, using 1OAWG ground wire and corrosion-resistant connectors.
Refer to the National Electrical Code for grounding details.
IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:
DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.
Use a non-conductive dry board, stick or rope to push or drag them so they no longer are in contact with electrical power.
Once they are no longer contacting electrical power, administer CPR if you are certified, and make sure that emergency medical aid has been requested.
-13-
3.3 Installing the AP
Please install the AP according to the following Steps. Don't forget to pull out the power plug and keep your hands dry.
Step 1. Push the latch on the bottom of the WMC251-150 to remove the sliding cover.
Figure 3-1 Connect the Antenna
Step 2. Plug the RJ45 Ethernet cable into the PoE LAN Port of the WMC251-150. Then, slide back the cover of the WMC251-150 to finish the installation.
Figure 3-2 Connect the Ethernet cable
Step 3. Plug the power cord into the DC port and plug the other end of the RJ45 cable into the POE port of the
PoE injector (See Step 2).
-14-
Step 4. Successful installation.
Figure 3-3 Connect the PoE injector
Figure 3-4 Connect the PoE injector
-15-
Step 5. Pole Mounting:
Place the strap through the slot on the back of the WMC251-1W-2T-150 and then around the pole. Tighten the strap to secure the WMC251-1W-2T-150.
Figure 3-5 Pole Mounting
-16-
Chapter 4. Quick Installation Guide
This chapter will show you how to configure the basic functions of your AP within minutes.
A computer with wired Ethernet connection to the Wireless AP is required for the first-time configuration.
4.1 Manual Network Setup - TCP/IP Configuration
The default IP address of the WMC251-150 is 192.168.0.100
. And the default Subnet Mask is 255.255.255.0.
These values can be changed as you want. In this guide, we use all the default values for description.
Connect the WMC251-150 with your PC by an Ethernet cable plugging in LAN port on one side and in LAN port of PC on the other side. Please power on the WMC251-150 by PoE injector through the PoE port.
In the following sections, we’ll introduce how to install and configure the TCP/IP correctly in Windows 7. And the procedures in other operating systems are similar. First, make sure your Ethernet Adapter is working, and refer to the Ethernet adapter manual if needed.
4.1.1 Configuring the IP Address Manually
Summary:
Set up the TCP/IP Protocol for your PC.
Configure the network parameters. The IP address is 192.168.1.xxx (if the default IP address of the
WMC251-150 is 192.168.0.100, and the DSL router is 192.168.0.254, the "xxx" can be configured to any number from 1 to 252), Subnet Mask is 255.255.255.0.
1 Select Use the following IP address radio button, and then configure the IP address of the PC.
2 For example, as the default IP address of the WMC251-150 is 192.168.0.100 and the DSL router is
192.168.0.254, you may choose from 192.168.0.1 to 192.168.0.252.
-17-
Figure 4-1 TCP/IP Setting
Now click OK to save your settings.
Now, you can run the Ping command in the command prompt to verify the network connection between your
PC and the AP. The following example is in Windows 7 OS. Please follow the steps below:
1. Click on Start > Run.
2. Type “cmd” in the Search box.
Figure 4-2 Windows Start Menu
-18-
3. Open a command prompt, type ping 192.168.0.100 and then press Enter.
If the result displayed is similar to Figure 4-3 , it means the connection between your PC and the AP has been established well.
Figure 4-3 Successful result of Ping command
If the result displayed is similar to Figure 4-4 , it means the connection between your PC and the AP has failed.
Figure 4-4 Failed Result of Ping Command
If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your AP. Some firewall software programs may block a DHCP request on newly installed adapters.
-19-
4.2 Starting Setup in the Web UI
It is easy to configure and manage the AP with the web browser.
Step 1. To access the configuration utility, open a web-browser and enter the default IP address http://192.168.0.100
in the web address field of the browser.
Figure 4-5 Login by default IP address
After a moment, a login window will appear. Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key.
Figure 4-6 Login Window
Default IP Address: 192.168.0.100
Default User name: admin
Default Password: admin
If the above screen does not pop up, it may mean that your web-browser has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings on the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it.
-20-
Chapter 5. Configuring the AP
This chapter delivers a detailed presentation of AP’s functionalities and features under the main menu below, allowing you to manage the AP with ease.
Figure 5-1 Main Menu
5.1 Setup Wizard
The Setup Wizard will guide the user to configure the WMC251-1W-2T-150 easily and quickly. Select the Setup
Wizard on the left side of the screen and by clicking on Next on the Setup Wizard screen shown below, you will then name your WMC251-1W-2T-150 and set up its security.
Figure 5-2 Setup Wizard
Step 1: Setup Operation Mode
The AP supports three operation modes, Gateway, Bridge and Wireless ISP.
-21-
Each mode is suitable for different uses. Please choose the correct mode.
Figure 5-3 Wizard –Setup Operation Mode
-22-
Step 2: Time Zone Setting
The Time Configuration option allows you to configure, update, and maintain the correct time on the internal system clock. Daylight Saving can also be configured to automatically adjust the time when needed.
Step 3: Setup LAN Interface
Figure 5-4 Wizard – Time Zone Setup
Step 4: Setup WAN Interface
Figure 5-5 Wizard – Setup LAN Interface
The Wireless AP supports five access modes in the WAN side. Please choose the correct mode according to your ISP Service.
-23-
Figure 5-6 Wizard – WAN Interface Setup
Step 5: Wireless LAN Setting
Configure the wireless parameters according to your application. For this section you can set AP, Client, WDS and AP+WDS (Repeater) mode.
Figure 5-7 Wizard - Wireless LAN Setting
Step 6: Wireless Security Setting
Secure your wireless network by turning on the WPA or WEP security feature on the AP. For this section you can set WEP and WPA-PSK security mode.
-24-
Figure 5-8 Wizard - Wireless Security Setting
Click the Finished button to make your wireless configuration to take effect.
-25-
5.2 Operation Mode
This page shows the current operation mode, and users can set different modes to LAN and WLAN interface for
NAT and bridging function on the WMC251-150.
Figure 5-9 Operation Mode
-26-
The page includes the following fields:
Gateway
Object Description
In this mode, the device enables multi-user to share Internet via
ADSL/Cable Modem. The wireless port shares the same IP to ISP through Ethernet WAN port. The Wireless port acts the same as a LAN port while at AP Router mode.
Bridge In this mode, the device can be used to combine multiple local networks together to the same one via wireless connections, especially for a home or office where separated networks can't be connected easily together with a cable.
Wireless ISP In this mode, the device enables multi-user to share Internet from
WISP. The LAN port devices share the same IP from WISP through
Wireless port. While connecting to WISP, the Wireless port works as
a WAN port at Client Router mode. The Ethernet port acts as a LAN port.
-27-
5.3 TCP/IP Settings
This page is used to configure the parameters for local area network which connects to the LAN port of your AP.
Here you may change the setting for IP address, subnet mask, DHCP, etc.
5.3.1 LAN Interface
On the LAN Settings page, you can configure the IP parameters of the LAN on the screen as shown below.
Figure 5-10 LAN Setting
The page includes the following fields:
Object
IP Address
Subnet Mask
Default Gateway
DHCP
DHCP Client Range
Static DHCP
Description
The default LAN IP address of the WMC251-1W-2T-150 is
192.168.0.100. You can change it according to your request.
Default is 255.255.255.0. You can change it according to your request.
Default is 192.168.0.100. You can change it according to your request.
You can select a Disabled, Client, and Server. Default is Disabled, meaning the WMC251-150 must connect to a router to assign IP addresses to clients.
For the Server mode, you must enter the DHCP client IP address range in the field. And you can click the “Show Client” button to show the Active DHCP Client Table.
Click the “Set Static DHCP” button and you can reserve some IP addresses for those network devices with the specified MAC addresses anytime when they request IP addresses.
-28-
Domain Name Default is IFS.
802.1d Spanning Tree You can enable or disable the Spanning Tree function.
Clone MAC Address
UPnP Enable
You can input an MAC address here for using clone function.
You can enable or disable the UPnP function.
The UPnP feature allows the devices, such as Internet computers, to access the local host resources or devices as needed. UPnP devices can be automatically discovered by the UPnP service application on the LAN.
If you change the IP address of LAN, you must use the new IP address to login the
AP.
When the IP address of the WMC251-150 is changed, the clients on the network often need to wait for a while or even reboot before they can access the new IP address. For an immediate access to the AP, please flush the netbios cache on the client computer by running the “nbtstat –r” command before using the device name of the WMC251-150 to access its Web Management page.
5.3.2 WAN Interface
On the WAN Settings page, you can configure the IP parameters of the WAN on the screen as shown below.
-29-
The page includes the following fields:
Object
Figure 5-11 WAN Setting
Description
-30-
WAN Access Type Please select the corresponding WAN Access Type for the Internet, and fill the correct parameters from your local ISP in the fields which appear below.
DHCP Client Select DHCP Client to obtain IP Address information automatically from your ISP.
Static IP Select Static IP Address if all the Internet port’s IP information is provided to you by your ISP (Internet Service Provider). You will need to enter the IP address, subnet mask, gateway address, and DNS address provided to you by your ISP.
Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
IP Address
Enter the IP address assigned by your ISP.
Subnet Mask
Enter the Subnet Mask assigned by your ISP.
PPPoE
Default Gateway
Enter the Gateway assigned by your ISP.
DNS
The DNS server information will be supplied by your ISP.
Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services.
User Name
Enter your PPPoE user name.
PPTP
Password
Enter your PPPoE password.
Choose PPTP (Point-to-Point-Tunneling Protocol) if your ISP uses a
PPTP connection. Your ISP will provide you with IP information and
PPTP Server IP Address; of course, it also includes a username and password. This mode is typically used for DSL services.
IP Address
Enter the IP address.
Subnet Mask
Enter the Subnet Mask.
Server IP Address
Enter the PPTP Server IP address provided by your ISP.
User Name
Enter your PPTP user name.
Password
-31-
L2TP
Enter your PPTP password.
Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password.
IP Address
Enter the IP address.
Subnet Mask
Enter the Subnet Mask.
Server IP Address
Enter the L2TP Server IP address provided by your ISP.
User Name
Enter your L2TP user name.
Password
Enter your L2TP password.
This option specifies the Host Name of the Wireless AP. Host Name
MTU Size
Attain DNS
Automatically
Set DNS Manually
The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is
1492 Bytes. It is not recommended that you change the default MTU Size unless required by your ISP.
Select “Attain DNS Automatically”, the DNS servers will be assigned dynamically from your ISP.
If your ISP gives you one or two DNS addresses, select Set DNS Manually and enter the primary and secondary addresses into the correct fields.
Clone MAC
Address
You can input a MAC address here for using clone function.
Enable uPNP Check to disable/enable uPNP function (default = disabled)
Enable IGMP Proxy Check to disable/enable IGMP function (default = enabled)
Enable Ping Access on WAN
Check to enable the Ping Access on WAN function (default = disabled)
Enable Web Server
Access on WAN
Check to enable the Web Server Access on WAN function (default = disabled)
Check to enable the IPsec pass through on VPN connection function (default = enabled)
Enable IPsec pass through on VPN connection
Enable PPTP pass through on VPN connection
Check to enable the PPTP pass through on VPN connection function (default = enabled)
Enable L2TP pass through on VPN connection
Check to enable the L2TP pass through on VPN connection function (default = enabled)
-32-
Enable IPv6 pass through on VPN connection
Check to enable the IPv6 pass through on VPN connection function (default = disabled)
If you get Address not found error when you access a Web site, it is likely that your DNS servers are set up improperly. You should contact your ISP to get
DNS server addresses.
WAN IP, whether obtained automatically or specified manually, should NOT be on the same IP net segment as the LAN IP; otherwise, the router will not work properly. In case of emergency, press the hardware "Reset" button.
5.4 Wireless
The wireless menu contains submenus of the settings about wireless network. Please refer to the following sections for the details.
Figure 5-12 Wireless – Main Menu
5.4.1 Basic Settings
Choose menu “Wireless Basic Settings” and you can configure the wireless basic settings for the wireless network on this page. After the configuration is done, please click the “Apply Changes” button to save the settings.
First of all, the wireless AP supports multiple wireless modes for different network applications, which include:
AP
Multiple SSIDs
Universal Repeater
Client
WDS
AP+WDS
It is so easy to combine the WMC251-1W-2T-150 with the existing wired network. The WMC251-1W-2T-150 definitely provides a total network solution for the home and the SOHO users.
-33-
AP
Standard Access Point
Figure 5-13 Topology – AP Bridge Mode
Figure 5-14 Wireless Basic Settings of AP
The page includes the following fields:
Object Description
Disable Wireless LAN Check the box to disable the wireless function.
-34-
Interface
Band
Mode
SSID
Channel Width
Channel Number
Broadcast SSID
Data Rate
Associated Clients
Select the desired mode. Default is “2.4GHz (B+G+N)”. It is strongly recommended that you set the Band to “2.4GHz (B+G+N)”, and all of
802.11b, 802.11g, and 802.11n wireless stations can connect to the
WMC251-1W-2T-150.
2.4 GHz (B): 802.11b mode, rate is up to 11Mbps
2.4 GHz (G): 802.11g mode, rate is up to 54Mbps
2.4 GHz (N): 802.11n mode, rate is up to 150Mbps(1T1R)
2.4 GHz (B+G): 802.11b/g mode, rate is up to 11Mbps or 54Mbps
2.4 GHz (G+N): 802.11g/n mode, rate is up to 54Mbps or 150Mbps
2.4 GHz (B+G+N): 802.11b/g/n mode, rate is up to 11Mbps,
54Mbps, or 150Mbps
There are four kinds of wireless mode selections:
AP
Client
WDS
AP+WDS
If you select WDS or AP+WDS, please click “WDS Settings” submenu for the related configuration. Furthermore, click the “Multiple AP” button to enable multiple SSID function.
The ID of the wireless network. User can access the wireless network via the ID only. However, if you switch to Client Mode, this field becomes the SSID of the AP you want to connect with.
Default: WMC251-150
You can select 20MHz, or 40MHz.
You can select the operating frequency of wireless network.
Default: 11
If you enable “Broadcast SSID”, every wireless station located within the coverage of the AP can discover its signal easily. If you are building a public wireless network, enabling this feature is recommended. In private network, disabling “Broadcast SSID” can provide better wireless network security.
Default is “Enabled”.
Set the wireless data transfer rate to a certain value. Since most of wireless devices will negotiate with each other and pick a proper data transfer rate automatically, it’s not necessary to change this value unless you know what will happen after modification.
Default is “Auto”.
Click the “Show Active Clients” button to show the status table of active wireless clients.
-35-
Enable Universal
Repeater Mode
(Acting as AP and client simultaneously)
Universal Repeater is a technology used to extend wireless coverage.
To enable Universal Repeater mode, check the box and enter the
SSID you want to broadcast in the field below. Then please click
“Security” submenu for the related settings of the AP you want to connect with.
Multiple-SSID
Enable multiple-SSID can broadcast multiple WLAN SSID's using virtual interfaces. You can have different encryption settings for each WLAN and you can restrict what they have access to.
Figure 5-15 Topology – Multiple-SSID Mode
Choose menu “Wireless
→ Basic Settings → Multiple AP” to configure the device as a general wireless access point with multiple SSIDs.
Figure 5-16 Wireless Basic Settings – Multiple AP
The device supports up to four multiple Service Set Identifiers. You can back to the Basic Settings page to set the Primary SSID. The SSID’s factory default setting is WMC251-1W-2T-150 VAP1~4 (Multiple-SSID
1~4). The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. When the information for the new SSID is finished, click the Apply Changes button to let your changes take effect.
-36-
Figure 5-17 Multiple-SSID
Once you have applied and saved those settings, you can then go to the “Wireless
→ Security” page on the AP to set up security settings for each of the SSIDs.
Universal Repeater
This mode allows the AP with its own BSS to relay data to a root AP to which it is associated with WDS disabled. The wireless repeater relays signal between its stations and the root AP for greater wireless range.
Figure 5-18 Topology – Universal Repeater Mode
1. Example of how to configure Universal Repeater Mode. Please take the following steps:
To configure each wireless parameter, please go to the “Wireless
→ Basic Settings” page.
Step 1. Configure wireless mode to “AP” and then check “Enable Universal Repeater Mode (Acting as AP
and client simultaneously)”. Click “Apply Changes” to take effect.
-37-
Figure 5-19 Universal Repeater-1
Step 2. Go to Site Survey page to find the root AP. Select the root AP that you want to repeat the signal and then click “Next”.
-38-
Figure 5-20 Universal Repeater-2
Step 3. Select the correct encryption method and enter the security key. Then, click “Connect”.
Figure 5-21 Universal Repeater-3
Step 4. Check “Add to Wireless Profile” and click “Reboot Now”.
-39-
Figure 5-22 Universal Repeater-4
Step 5. Go to “Management-> Status” page to check whether the state of Repeater interface should be
“Connected”.
Figure 5-23 Universal Repeater-5
Client (Infrastructure)
Combine the Wireless AP to the Ethernet devices such as IP camera to make it be wireless station.
Figure 5-24 Topology – Client Mode
-40-
Figure 5-25 Wireless Basic Settings – Client
-41-
The page includes the following fields:
Object Description
Disable Wireless LAN Check the box to disable the wireless function.
Interface
Band
Mode
Network Type
SSID
Broadcast SSID
Select the desired mode. Default is “2.4GHz (B+G+N)”. It is strongly recommended that you set the Band to “2.4GHz (B+G+N)”, and all of
802.11b, 802.11g, and 802.11n wireless stations can connect to the
WMC251-150.
2.4 GHz (B): 802.11b mode, rate is up to 11Mbps
2.4 GHz (G): 802.11g mode, rate is up to 54Mbps
2.4 GHz (N): 802.11n mode, rate is up to 150Mbps(1T1R)
2.4 GHz (B+G): 802.11b/g mode, rate is up to 11Mbps or 54Mbps
2.4 GHz (G+N): 802.11g/n mode, rate is up to 54Mbps or 150Mbps
2.4 GHz (B+G+N): 802.11b/g/n mode, rate is up to 11Mbps,
54Mbps, or 150Mbps
There are four kinds of wireless mode selections:
AP
Client
WDS
AP+WDS
If you select WDS or AP+WDS, please click “WDS Settings” submenu for the related configuration. Furthermore, click the “Multiple AP” button to enable multiple SSID function.
In Infrastructure, the wireless LAN serves as a wireless station. And the user can use the PC equipped with the WMC251-150 to access the wireless network via other access points. In Ad hoc, the wireless
LAN will use the Ad-hoc mode to operate.
Default is “Infrastructure”.
Note: only while the wireless mode is set to “Client”, then the Network
Type can be configured.
The ID of the wireless network. User can access the wireless network via the ID only. However, if you switch to Client Mode, this field becomes the SSID of the AP you want to connect with.
Default: WMC251-150
If you enable “Broadcast SSID”, every wireless station located within the coverage of the WMC251-150 can discover its signal easily. If you are building a public wireless network, enabling this feature is recommended. In private network, disabling “Broadcast SSID” can provide better wireless network security.
Default is “Enabled”.
-42-
Data Rate Set the wireless data transfer rate to a certain value. Since most of wireless devices will negotiate with each other and pick a proper data transfer rate automatically, it’s not necessary to change this value unless you know what will happen after modification.
Default is “Auto”.
Enable Mac Clone
(Single Ethernet Client)
Enable Mac Clone.
Example of how to configure Client Mode. Please take the following steps:
To configure each wireless parameter, please go to the “Wireless
→ Basic Settings” page.
Step 1. Go to “Wireless
→ Site Survey” page and click “Site Survey” button.
Figure 5-26 Client – Survey
-43-
Step 2. Choose the root AP from the list. If the root AP is not listed in the table, re-click “Site Survey” to update the list.
Figure 5-27 Client – AP List
Step 3. Enter the Security Key of the root AP and then click “Connect”.
Figure 5-28 Client – Security
-44-
Step 4. Wait until the connection established. Check the “Add to Wireless Profile” option and then reboot it.
Figure 5-29 Client – Status
WDS
Connect this Wireless AP with up to 8 WDS-capable wireless APs to expand the scope of network.
Figure 5-30 Topology – WDS PtP Mode
Figure 5-31 Topology – WDS PtMP Mode
-45-
Figure 5-32 Wireless Basic Settings – WDS
The page includes the following fields:
Object Description
Disable Wireless LAN Check the box to disable the wireless function.
Interface
Band Select the desired mode. Default is “2.4GHz (B+G+N)”. It is strongly recommended that you set the Band to “2.4GHz (B+G+N)”, and all of
802.11b, 802.11g, and 802.11n wireless stations can connect to the
WMC251-150.
2.4 GHz (B): 802.11b mode, rate is up to 11Mbps
2.4 GHz (G): 802.11g mode, rate is up to 54Mbps
2.4 GHz (N): 802.11n mode, rate is up to 150Mbps(1T1R)
2.4 GHz (B+G): 802.11b/g mode, rate is up to 11Mbps or 54Mbps
2.4 GHz (G+N): 802.11g/n mode, rate is up to 54Mbps or 150Mbps
-46-
Mode
Channel Width
Control Sideband
Channel Number
Data Rate
2.4 GHz (B+G+N): 802.11b/g/n mode, rate is up to 11Mbps,
54Mbps, or 150Mbps
There are four kinds of wireless mode selections:
AP
Client
WDS
AP+WDS
If you select WDS or AP+WDS, please click “WDS Settings” submenu for the related configuration. Furthermore, click the “Multiple AP” button to enable multiple SSID function.
You can select 20MHz, or 40MHz
You can select Upper or Lower.
You can select the operating frequency of wireless network.
Set the wireless data transfer rate to a certain value. Since most of wireless devices will negotiate with each other and pick a proper data transfer rate automatically, it’s not necessary to change this value unless you know what will happen after modification.
Default is “Auto”.
AP+ WDS
Connect this Wireless AP with up to 8 WDS-capable wireless APs, and connect another AP to provide service for all wireless stations within its coverage.
Figure 5-33 Topology – WDS+AP Mode
-47-
Figure 5-34 Wireless Basic Settings – WDS+AP
The page includes the following fields:
Object Description
Disable Wireless LAN Check the box to disable the wireless function.
Interface
Country Select your region from the pull-down list.
This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance.
Band Select the desired mode. Default is “2.4GHz (B+G+N)”. It is strongly recommended that you set the Band to “2.4GHz (B+G+N)”, and all of
802.11b, 802.11g, and 802.11n wireless stations can connect to the
WMC251-150.
2.4 GHz (B): 802.11b mode, rate is up to 11Mbps
-48-
Mode
SSID
2.4 GHz (G): 802.11g mode, rate is up to 54Mbps
2.4 GHz (N): 802.11n mode, rate is up to 150Mbps(1T1R)
2.4 GHz (B+G): 802.11b/g mode, rate is up to 11Mbps or 54Mbps
2.4 GHz (G+N): 802.11g/n mode, rate is up to 54Mbps or 150Mbps
2.4 GHz (B+G+N): 802.11b/g/n mode, rate is up to 11Mbps,
54Mbps, or 150Mbps
There are four kinds of wireless mode selections:
AP
Client
WDS
AP+WDS
If you select WDS or AP+WDS, please click “WDS Settings” submenu for the related configuration. Furthermore, click the “Multiple AP” button to enable multiple SSID function.
The ID of the wireless network. User can access the wireless network via the ID only. However, if you switch to Client Mode, this field becomes the SSID of the AP you want to connect with.
Default: WMC251-1W-2T-150
Channel Width
Control Sideband
Channel Number
You can select 20MHz, or 40MHz
You can select Upper or Lower.
You can select the operating frequency of wireless network.
Broadcast SSID If you enable “Broadcast SSID”, every wireless station located within the coverage of the WMC251-150 can discover its signal easily. If you are building a public wireless network, enabling this feature is recommended. In private network, disabling “Broadcast SSID” can provide better wireless network security.
Default is “Enabled”.
Data Rate Set the wireless data transfer rate to a certain value. Since most of wireless devices will negotiate with each other and pick a proper data transfer rate automatically, it’s not necessary to change this value unless you know what will happen after modification.
Associated Clients
Enable Universal
Repeater Mode
(Acting as AP and client simultaneously)
Default is “Auto”.
Click the “Show Active Clients” button to show the status table of active wireless clients.
Universal Repeater is a technology used to extend wireless coverage.
To enable Universal Repeater Mode, check the box and enter the
SSID you want to broadcast in the field below. Then please click
“Security” submenu for the related settings of the AP you want to connect with.
-49-
5.4.2 Advanced Settings
Choose menu “Wireless Advanced Settings” to configure the wireless advanced settings for the wireless network on this page. After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-35 Wireless Advanced Settings
-50-
The page includes the following fields:
Object
Fragment Threshold
RTS Threshold
Beacon Interval
Preamble Type
IAPP
Protection
Aggregation
Short GI
WLAN Partition
STBC
LDPC
20/40MHz Coexist
Multicast to Unicast:
When the packet size is smaller than the RTS threshold, the access point will not use the RTS/CTS mechanism to send this packet.
Default is “2347”.
The interval of time that this access point broadcasts a beacon.
Beacon is used to synchronize the wireless network. Default is “100”.
Preamble type defines the length of CRC block in the frames during the wireless communication. “Short Preamble” is suitable for high traffic wireless network. “Long Preamble” can provide more reliable communication. Default is “Long Preamble”.
IAPP (Inter-Access Point Protocol) enabled is recommended as it describes an optional extension to IEEE 802.11 that provides wireless access-point communications among multivendor systems.
Default is “Enabled”.
Enables a backward compatible protection mechanism for 802.11b clients. When the protection mode is enabled can slow the throughput of the 802.11g/n clients by as much as 50%.
Default is “Disabled”.
It is a function where the values of multiple rows are grouped together.
Default is “Enabled”
It is used to set the time that the receiver waits for RF reflections to settle out before sampling data.
Default is “Enabled”
This feature also called “WLAN isolation” or “Block Relay”. If this is enabled, wireless clients cannot exchange data through the
WMC251-1W-2T-150.
Default is “Disabled”.
Activate Space Time Blocking Code (STBC) which does not need channel statement information (CSI).
Default Setting: "Enabled"
Low-density Parity-check Code is wireless data transmit algorithm.
Default Setting: "Enabled"
Configure 20/40MHz coexisting scheme.
If you set up as "Enabled", "20MHz" and "40MHz" will coexist.
Default Setting: "Disabled"
Enables multicast traffic streams to be converted to unicast traffic before delivery to wireless clients. Converting multicast traffic to unicast before sending to wireless clients allows a longer DTIM (Data Beacon
Rate) interval to be set. A longer DTIM interval prevents clients in power-save mode having to activate their radios to receive the multicast
-51-
Description
You can specify the maximum size of packet during the fragmentation of data to be transmitted. If you set this value too low, it will result in bad performance.
Default is “2346”.
RF Output Power data, which reduce power consumption.
Default Setting: “Enabled”
Users can adjust the wireless output power to different levels. For short distance of PtP connection within 1Km, it is suggested to reduce the output power to 50% or lower to prevent interference with each other.
Default is “100%”.
5.4.3 Security
Choose menu “Wireless Security” to configure the settings of wireless security for the wireless network on this page. After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-36 Wireless Security Settings
The page includes the following fields:
Object
Select SSID
Encryption
Description
Select the SSID you want to configure the wireless security function, which includes the root one and the client one.
Disable:
No security setup for wireless connection.
WEP:
It is based on the IEEE 802.11 standard. And the default setting of authentication is Automatic, which can select Open System or Shared Key authentication type automatically based on the wireless station's capability and request. Furthermore, you can select Key Length and enter 10 and 26
Hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 5 and 13 ASCII characters in the Encryption Key field.
WPA2:
WPA2 is a high level encryption and is supported by most wireless devices and operating systems.
WPA-Mixed:
WPA Mixed Mode allows the use of both WPA and WPA2 at the same time.
-52-
Authentication Mode Enterprise (RADIUS)
When you select the authentication mode based on Enterprise (Radius
Server), please enter the IP Address, Port, and Password of the Radius
Server.
Personal (Pre-Shared Key)
When you select the other authentication mode based on Personal
(Pre-Shared Key), please enter at least 8 ASCII characters (Passphrase) or
64 Hexadecimal characters. All of the Cipher Suites support TKIP and AES.
802.1x Authentication Enable 802.1x authentication function and then enter the IP Address, Port, and Password of the Radius Server.
Disable:
Authentication is disabled and no password/key is required to connect to the access point.
WEP:
WEP (Wired Equivalent Privacy) is a basic encryption. For a higher level of security consider using the WPA encryption.
Figure 5-37 Security Settings – WEP
The page includes the following fields:
Object
Encryption
802.1x
Authentication
Authentication
Description
You can disable the encryption or select WEP, WPA2, and WPA-Mixed as the encryption method to your wireless network.
Enable 802.1x authentication function and then enter the IP Address,
Port, and Password of the Radius Server.
Configures the WEP security mode used by clients.
When using WEP, be sure to define at least one static WEP key for the
Wireless AP and all its clients.
-53-
Key Length
There are three options provided:
Open System — this authentication accepts any client attempting to connect the Wireless AP without verifying its identity.
Shared Key — the shared-key security uses a WEP key to authenticate clients connecting to the network and for data encryption.
Auto — allows wireless clients to connect to the network using
Open-WEP (uses WEP for encryption only) or Shared-WEP (uses WEP for authentication and encryption).
Choose the WEP key length. You can choose 64-bit or 128-bit.
Key Format
Encryption Key
You can choose ASCII or Hex format.
Enter 5 alphanumeric characters or 10 hexadecimal digits for 64-bit keys, or enter 13 alphanumeric characters or 26 hexadecimal digits for
128-bit keys.
WPA2:
Wi-Fi Protected Access (WPA) was introduced as an interim solution for the vulnerability of WEP pending the adoption of a more robust wireless security standard. WPA2 includes the complete wireless security standard, but also offers backward compatibility with WPA. Both WPA and WPA2 provide an enterprise and personal mode of operation.
Figure 5-38 Security Settings – WPA2 Personal
The page includes the following fields:
Object
Encryption
Description
You can disable the encryption or select WEP, WPA2, and WPA-Mixed as the encryption method to your wireless network.
Authentication Mode
Select “Enterprise (RADIUS)” for user authentication and you will require a
RADIUS authentication server to be configured on the wired network. Select
-54-
Management Frame
Protection
WPA2 Cipher Suite
“Personal (Pre-Shared Key)” and you will require a pre-shared key to be configured for client authentication.
Management frame protection (MFP) provides security for the otherwise unprotected and unencrypted 802.11 management messages passed between access points and clients. MFP provides both infrastructure and client support. If you choose this to “Required”, then clients are allowed to associate only if MFP is negotiated. If you choose “Capable”, then the non-supporting clients are allows to associate (without using MFP).
Selects the data encryption type to use. (Default is determined by the
Encryption Mode selected.)
TKIP — Uses Temporal Key Integrity Protocol (TKIP) keys for encryption.
WPA specifies TKIP as the data encryption method to replace WEP. TKIP avoids the problems of WEP static keys by dynamically changing data encryption keys.
AES — Uses Advanced Encryption Standard (AES) keys for encryption.
WPA2 uses AES Counter-Mode encryption with Cipher Block Chaining
Message Authentication Code (CBC-MAC) for message integrity. The AES
Counter-Mode/CBCMAC Protocol (AESCCMP) provides extremely robust data confidentiality using a 128- bit key. Use of AES-CCMP encryption is specified as a standard requirement for WPA2. Before implementing WPA2 in the network, be sure client devices are upgraded to WPA2-compliant hardware.
Pre-Shared Key Format Specify the format of the key, pass phrase or hex.
The WPA Pre-shared Key can be input as an ASCII string (an easy-to-remember form of letters and numbers that can include spaces) or
Hexadecimal format. (Range: 8~63 ASCII characters, or exactly 64
Hexadecimal digits)
Pre-Shared Key Enter the key whose format is limited by the key format.
-55-
Figure 5-39 Security Settings – WPA2 Enterprise
The page includes the following fields:
Object
Encryption
Description
You can disable the encryption or select WEP, WPA2, and WPA-Mixed as the encryption method to your wireless network.
Authentication Mode
Management Frame
Protection
Select “Enterprise (RADIUS)” for user authentication and you will require a
RADIUS authentication server to be configured on the wired network. Select
“Personal (Pre-Shared Key)” and you will require a pre-shared key to be configured for client authentication.
Management frame protection (MFP) provides security for the otherwise unprotected and unencrypted 802.11 management messages passed between access points and clients. MFP provides both infrastructure and client support. If you choose this to “Required”, then clients are allowed to associate only if MFP is negotiated. If you choose “Capable”, then the non-supporting clients are allows to associate (without using MFP).
Selects the data encryption type to use. (Default is determined by the
Encryption Mode selected.)
WPA2 Cipher Suite
TKIP — Uses Temporal Key Integrity Protocol (TKIP) keys for encryption.
WPA specifies TKIP as the data encryption method to replace WEP. TKIP avoids the problems of WEP static keys by dynamically changing data encryption keys.
AES — Uses Advanced Encryption Standard (AES) keys for encryption.
WPA2 uses AES Counter-Mode encryption with Cipher Block Chaining
Message Authentication Code (CBC-MAC) for message integrity. The AES
-56-
Counter-Mode/CBCMAC Protocol (AESCCMP) provides extremely robust data confidentiality using a 128- bit key. Use of AES-CCMP encryption is specified as a standard requirement for WPA2. Before implementing WPA2 in the network, be sure client devices are upgraded to WPA2-compliant hardware.
RADIU Server IP
Address
Enter the RADIUS server host IP address.
RADIU Server Port
RADIU Server
Password
Set the UDP port used in the authentication protocol of the RADIUS server.
(Range: 1024-65535; Default: 1812)
A shared text string used to encrypt messages between the access point and the RADIUS server. Be sure that the same text string is specified on the
RADIUS server. Do not use blank spaces in the string.
Enter a shared secret/password between 1 and 99 characters in length.
WPA-Mixed:
Please refer to the WPA2 section for the definition of each field.
Figure 5-40 Security Settings – WPA-Mixed Personal
-57-
Figure 5-41 Security Settings – WPA-Mixed Enterprise
802.1x Authentication:
IEEE 802.1X is a standard framework for network access control that uses a central RADIUS server for user authentication. This control feature prevents unauthorized access to the network by requiring an 802.1X client application to submit user credentials for authentication.
Figure 5-42 Security Settings – 802.1x Authentication
The page includes the following fields:
Object
Encryption
Description
You can disable the encryption or select WEP, WPA2, and WPA-Mixed as the encryption method to your wireless network.
802.1x Authentication
RADIU Server IP
Enable 802.1x authentication function and then enter the IP Address, Port, and Password of the Radius Server.
Enter the RADIUS server host IP address.
-58-
Address
RADIU Server Port
RADIU Server
Password
Set the UDP port used in the authentication protocol of the RADIUS server.
(Range: 1024-65535; Default: 1812)
A shared text string used to encrypt messages between the access point and the RADIUS server. Be sure that the same text string is specified on the
RADIUS server. Do not use blank spaces in the string.
Enter a shared secret/password between 1 and 99 characters in length.
5.4.4 Access Control
Choose menu “Wireless Access Control” to allow or deny the computer of specified MAC address to connect with the WMC251-1W-2T-150 on this page. After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-43 Wireless Access Control
The page includes the following fields:
Object
Wireless Access
Control Mode
MAC Address
Description
You can choose to set the Allowed-List, Denied-List, or disable this function.
Comment
Enter the MAC address you want to allow or deny connection to the
WMC251-1W-2T-150 in the field.
You can make some comment on each MAC address on the list.
-59-
Current Access Control
List
You can select some MAC addresses and click the “Delete Selected” button to delete it.
Wireless Access Control example:
To deny a PC at the MAC address of 9c:F6:1A:00:00:01 to connect to your wireless network, do as follows:
Step 1. Select “Deny” from MAC Address Filter drop-down menu.
Step 2. Enter 9c:F6:1A:00:00:01 in the MAC address box and click “Add”.
Step 3. Click the “OK” button to save your settings and you can add more MAC addresses, if you like, simply repeat the above steps.
Figure 5-44 Wireless Access Control – Deny
-60-
5.4.5 WDS
WDS (Wireless Distribution System) feature can be used to extend your existing wireless network coverage.
Before configuring the WDS Setting page, you have to select the wireless mode to “WDS” on the Wireless ->
Basic Settings web page.
-61-
Figure 5-45 WDS Mode
Choose menu “Wireless WDS Settings” to configure WDS to connect the WMC251-1W-2T-150 with another
AP on this page. After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-46 WDS Settings
The page includes the following fields:
Object
Enable WDS
MAC Address
Data Rate
Comment
Set Security
Show Statics
Current WDS AP List
Description
Check the box to enable the WDS function. Please select WDS or
AP+WDS in the Mode of Wireless Basic Settings before you enable
WDS on this page.
You can enter the MAC address of the AP you want to connect with.
Default is “Auto”.
You can make some comment for each MAC address on the list.
Click the “Set Security” button to configure the wireless security parameters of the AP you want to connect via WDS.
Click the “Show Statics” button to show the WDS AP.
You can select some MAC addresses of the AP and click the “Delete
Selected” button to delete it.
-62-
Once clicked “Set Security” to enter the following page to configure the encryption method and pre-shared key for the WDS connection.
Figure 5-47 WDS – Set Security
WDS feature can only be implemented between 2 wireless devices that both support the
WDS feature. Plus, channel, security settings and security key must be the same on both such devices.
To encrypt your wireless network, click “Set Security”. For the detail of wireless security,
. Do remember to reboot the device after you save your wireless
security settings; otherwise, the WDS feature may not function.
5.4.6 Site Survey
Choose menu “Wireless Site Survey” to scan the available local AP. If any Access Point is found, you could choose any one to connect with manually when the Client Mode is enabled.
-63-
Figure 5-48 Site Survey
5.4.7 WPS
WPS (Wi-Fi Protected Setup) is designed to ease setup of security Wi-Fi networks and subsequently network management. This Wireless Router supports WPS features for AP mode, AP+WDS mode,
Infrastructure-Client mode, and the wireless root interface of Universal Repeater mode.
Simply enter a PIN code or press the software PBC button or hardware WPS button (if any) and a secure wireless connection is established.
PBC: If you find the WPS LED blinking for 2 minutes after you press the hardware WPS button on the device, it means that PBC encryption method is successfully enabled. And an authentication will be performed between your router and the WPS/PBC-enabled wireless client device during this time; if it succeeds, the wireless client device connects to your device, and the WPS LED turns off. Repeat steps mentioned above if you want to connect more wireless client devices to the device.
PIN:To use this option, you must know the PIN code from the wireless client and enter it in corresponding field on your device while using the same PIN code on client side for such connection.
The page includes the following fields:
Object
Disable WPS
Description
You can check the box to disable the WPS function.
-64-
WPS Status
Self-PIN Number
Push Button
Configuration
Client PIN Number
Here you can check if the connection via WPS is established or not.
It is the PIN number of the WMC251-1W-2T-150 here.
Click the “Start PBC” to activate WPS as well in the client device within
2 minutes.
In addition to the PBC method, you can also use the PIN method to activate the WPS. Just enter the PIN number of the client device in the field and click the “Start PIN” button.
The WPS encryption can be implemented only between your Router and another
WPS-capable device.
Example of how to establish wireless connection using WPS. Please take the following steps:
Step 1. Choose menu “Wireless WPS” to configure the setting for WPS. After the configuration, please click the “Apply Changes” button to save the settings.
Step 2. Add a new device.
If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and AP using either Push Button Configuration (PBC) method or PIN method.
To build a successful connection by WPS, you should also do the corresponding configuration of the new device for WPS function.
A. By Push Button Configuration (PBC) i. Click the “Start PBC” Button on the WPS page of the AP.
Figure 5-49 WPS-PBC
-65-
ii.
Figure 5-50 WPS-PBC
Press and hold the WPS Button equipped on the adapter directly for 2 or 3 seconds. Or you can click the WPS button with the same function in the configuration utility of the adapter. The process must be finished within 2 minutes. iii. Wait for a while until the next screen appears. Click OK to complete the WPS configuration.
B. By PIN
If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods.
Method One: Enter the PIN of your Wireless adapter into the configuration utility of the AP i. Enter the PIN code of the wireless adapter in the field behind Client PIN Number in the following figure and then click Start PIN.
The PIN code of the adapter is always displayed on the WPS configuration screen.
Figure 5-51 WPS-PIN
-66-
Figure 5-52 WPS-PIN ii. For the configuration of the wireless adapter, please choose the option that you want to enter PIN
into the AP (Enrollee) in the configuration utility of the WPS and click Next until the process finishes.
Method Two: Enter the PIN of the AP into the configuration utility of your Wireless adapter i. Click the “Start PBC” Button on the WPS page of the AP. Get the Current PIN code of the AP in WPS page (each AP has its unique PIN code). ii.
Figure 5-53 WPS-PIN
For the configuration of the wireless adapter, please choose the option that you want to enter the PIN
of the AP (Registrar) in the configuration utility of the Wireless adapter and enter it into the field.
Then click Next until the process finishes.
5.4.8 Schedule
Wireless Schedules will enable or disable your wireless access at a set time based on your predefined schedule.
This feature is often used for restricting access to all users (such as children, employees and guests) during specific times of the day for parental control or security reasons.
Choose menu “Wireless Schedule” to configure the schedule rule of enabling wireless function. After the configuration, please click the “Apply Changes” button to save the settings.
-67-
Figure 5-54 Schedule
When setting the Wireless Schedule, it is important to ensure that your System Clock settings have been configured. If not, your Wireless Schedule will not function correctly.
-68-
5.5 Firewall
This section contains firewall settings include Port/IP/MAC/URL Filtering/Forwarding and DMZ which are only functioning when the AP configured to “Gateway” mode. Please refer to the following sections for the details.
Figure 5-55 Firewall – Main Menu
5.5.1 Port Filtering
Choose menu “Firewall Port Filtering”, and you can configure to re-direct a particular range of service port numbers from the Internet network to a particular LAN IP address. It helps users to host some servers behind the firewall. After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-6-1 Port Filtering
The page includes the following fields:
Object
Enable Port Filtering
Port Range
Protocol
Description
Enable Port Filtering function
Add ports you want to control. For TCP and UDP Services, enter the beginning of the range of port numbers used by the service. If the service uses a single port number, enter it in both the start and finish fields.
Select the port number protocol type (TCP, UDP or both). If you are unsure, then leave it to the default both protocol
-69-
Comment The description of this setting
Check the “Select” box of which rule you want to delete, and then click the “Delete Selected” button to delete it.
5.5.2 IP Filtering
IP Filtering is used to block internet or network access to specific IP addresses on your local network. The restricted user may still be able to login to the network but will not be able to access the internet. To begin blocking access to an IP address, enable IP Filtering and enter the IP address of the user you wish to block.
Choose menu “Firewall IP Filtering”, and you can configure which IP address and protocol to be restricted.
After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-6-1 IP Filtering
The page includes the following fields:
Object
Enable IP Filtering
Local IP Address
Description
Check this box to enable IP Filter function
Add LAN IP address you want to control
Protocol
Comment
Select the port number protocol type (TCP, UDP or both). If you are unsure, then leave it to the default both protocol
The description of this setting
Check the “Select” box of which rule you want to delete, and then click the “Delete Selected” button to delete it.
5.5.3 MAC Filtering
Entries in this table are used to restrict certain types of data packets from your local network to Internet through
-70-
the Wireless Router. Use of such filters can be helpful in securing or restricting your local network.
Choose menu “Security Setup MAC Filter”, and you can configure which computer of the specified MAC address to be restricted. After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-7-4 MAC Filtering
The page includes the following fields:
Object
Enable MAC Filtering
MAC Address
Comment
Description
Enable MAC filtering
Add MAC address you want to control. You can add maximum 20 MAC
Addresses in the table.
The description of this setting
Check the “Select” box of which rule you want to delete, and then click the “Delete Selected” button to delete it.
-71-
5.5.4 Port Forwarding
Choose menu “Firewall Port Forwarding”, and you can configure to re-direct a particular range of service port numbers from the Internet network to a particular LAN IP address. It helps users to host some servers behind the firewall.
After the configuration, please click the “Apply Changes” button to save the settings.
The page includes the following fields:
Figure 5-6-1 Port Forwarding
Object
Enable Port Forwarding Enable Port Forwarding function
Description
IP Address Add LAN IP address of specified host or server on the private local network
Protocol
Port Range
Comment
Select the port number protocol type (TCP, UDP or both). If you are unsure, then leave it to the default both protocol
Add ports you want to control. For TCP and UDP Services, enter the beginning of the range of port numbers used by the service. If the service uses a single port number, enter it in both the start and finish fields.
The description of this setting
Check the “Select” box of which rule you want to delete, and then click the “Delete Selected” button to delete it.
-72-
5.5.5 URL Filtering
URL filter is used to deny LAN users from accessing the internet. Block those URLs which contain keywords listed below.
Choose menu “Firewall URL Filtering”, and you can configure which URL addresses to be blocked. After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-7-3 URL Filtering
The page includes the following fields:
Object
Enable URL Filtering:
Description
Check this box to enable URL Filter function.
IP Address:
URL Address:
The IP Address that you want to filter.
The URL Address that you want to filter.
Check the “Select” box of which rule you want to delete, and then click the “Delete Selected” button to delete it.
If you wish to block www.facebook.com, simply type in "facebook" and the Wireless
AP/Router will block all websites with the text "facebook" in the URL.
-73-
5.5.6 DMZ
This page allows you to set a De-militarized Zone (DMZ) to separate internal network and Internet.
Choose menu “Firewall DMZ”, and you can configure the private IP address of DMZ. The DMZ feature allows one local host to be exposed to the Internet for a special-purpose service such as Internet gaming or video conferencing. After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-6-2 DMZ
The page includes the following fields:
Object
Enable DMZ
DMZ Host IP Address
Description
Check the box to enable DMZ function. If the DMZ Host Function is enabled, it means that you set up DMZ host at a particular computer to be exposed to the Internet so that some applications/software, especially Internet / online game can have two way connections.
Enter the IP address of a particular host in your LAN which will receive all the packets originally going to the WAN port / Public IP address above.
5.6 QoS
The QoS (Quality of Service) helps improve your network gaming performance by prioritizing applications. By default the bandwidth control are disabled and application priority is not classified automatically. In order to complete this settings, please follow the steps below.
1. Enable this function.
2. Enter the total speed or choose automatic mode.
3. Enter the IP address or MAC address user want to control.
4. Specify how to control this PC with this IP address or MAC address, including maximum or minimum bandwidth, priority and its up/down speed.
-74-
After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-9-1 QoS
The page includes the following fields:
Object
Enable QoS
Automatic Uplink Speed
Description
Check the box to enable the QoS function.
Automatic Downlink
Speed
QoS Rule Setting
Check the box to adjust the uplink speed automatically by the WMC251-150.
Or enter the uplink data rate manually in the field below.
Check the box to adjust the downlink speed automatically by the
WMC251-150. Or enter the downlink data rate manually in the field below.
To set the priority rule, you can appoint the computer by IP address or MAC address, and enter it in the correct field. Select minimum or maximum bandwidth, and then fill the uplink and downlink data rate into the field.
-75-
5.7 Management
This section focuses on how to maintain AP, including Restore to Factory Default Setting, Backup/Restore,
Firmware Upgrade, Reboot, Password Change and Syslog.
Figure 5-56 Management – Main Menu
5.7.1 Status
You can use this function to realize the instantaneous information of the Wireless AP. The Information displayed here may vary on different configurations.
Choose menu “Management Status” to show the current status and some basic settings of the
WMC251-150.
Figure 5-57 Status
-76-
5.7.2 Statistics
Choose menu “Management Statistics” to show the packet counters for transmission and reception regarding wireless and Ethernet network.
Figure 5-58 Statistics
The page includes the following fields:
Object
Wireless LAN
Sent Packets
Wireless LAN
Received Packets
Ethernet LAN
Sent Packets
Ethernet LAN
Received Packets
Refresh
Description
It shows the statistic count of sent packets on the wireless LAN interface.
It shows the statistic count of received packets on the wireless LAN interface.
It shows the statistic count of sent packets on the Ethernet LAN interface.
It shows the statistic count of received packets on the Ethernet LAN interface.
Click the refresh the statistic counters on the screen.
5.7.3 DDNS (Dynamic DNS Settings)
Enable “Operation Mode” “Gateway” or “Wireless ISP” mode and then enter the “DDNS” page by choosing menu “Management DDNS”. This section allows you to configure the DDNS settings.
-77-
Figure 5-59 Dynamic DNS Settings
Object
• Enable DDNS
• Service Provider
• Domain Name
Description
Disable: Disable DDNS function
Enable Easy DDNS: Enable IFS Easy DDNS
Enable Dynamic DDNS: You are allowed to modify the DDNS settings.
Select a server provider or disable the existing server.
Enter the host name or domain name provided by DDNS provider.
Enter the DDNS user name of the DDNS account.
• Account
• Password
Enter the DDNS password of the DDNS account.
Enable “Operation Mode” “Gateway” or “Wireless ISP” mode and then enter the “DDNS” page by choosing menu “Management DDNS”.
Step 1. Select “Enable Dynamic DDNS” from the list of Dynamic DNS Provider to use your DDNS service.
-78-
Step 2. Configure the DDNS account that has been registered in IFS DDNS website.
Domain Name: Enter your DDNS host (format: xxx.Yourddns.com
, xxx is the registered domain name)
User Name/Email: Enter your registered DDNS user name.
Password: Enter the password of your account.
Step 3. Go to “TCP/IP Settings WAN Interface Setup” to enable Web Server Access on WAN port and configure WAN connection to Static IP (fixed IP).
-79-
Step 4. Save the setting and connect your WAN port of the Wireless AP to the internet via Ethernet cable.
In a remote computer, enter the DDNS host name as the figure shown below. Then, you should be able to login the WMC251-1W-2T-150 remotely.
Example of Easy DDNS Settings:
This service is not required to register any DDNS account.
Please refer to the procedure listed as follows to configure using IFS Easy DDNS service.
Step 1. Select “Enable Easy DDNS” to use the IFS Easy DDNS service.
Domain Name: Display the specified domain name for this device. (Format: xxxxxx.Yourddns.com
, xxxxxx is the last six-digit of the WAN Port MAC address)
-80-
Step 2. Go to “TCP/IP Settings WAN Interface Setup” to enable Web Server Access on WAN port and configure WAN connection to Static IP (fixed IP).
Step 3. Save the setting and connect your WAN port of the Wireless AP to the internet via Ethernet cable.
WMC251-1W-2T-150 remotely.
5.7.4 Time Zone Setting
This section assists you in setting the Wireless AP’s system time. You can either select to set the time and date manually or automatically obtain the GMT time from Internet.
Choose menu “Management Time Zone Setting” to configure the system time. You can also maintain the system time by synchronizing with a public time server over the Internet. After the configuration, please click the
“OK” button to save the settings.
-81-
The configured time and date settings are lost when the Wireless AP is powered off.
The page includes the following fields:
Figure 5-60 Time Zone Settings
Object
Current Time
Time Zone Select
Description
Input current time manually.
You can click “Copy Computer Time” button to copy the PC’s current time to the AP.
Select the time zone of the country you are currently in. The router will set its time based on your selection.
Automatically Adjust
Daylight Saving
Enable NTP client update
NTP Server
Select the time offset, if your location observes daylight saving time.
Check to enable NTP update. Once this function is enabled, AP will automatically update current time from NTP server.
User may select prefer NTP sever or input address of NTP server manually.
If the AP loses power for any reason, it cannot keep its clock running, and will not have the correct time when it is started again. To maintain correct time for schedules and logs, either you must enter the correct time after you restart the AP, or you must enable the
NTP Server option.
-82-
5.7.5 Schedule Reboot
This page allows you to enable and configure system reboot schedule. The device can regularly reboot according to the reserved time when connecting to the Internet.
Figure 5-61 Schedule Reboot
The page includes the following fields:
Object
Schedule Reboot
Setting
Reboot Time
Reboot Plan
Description
Enable or disable the Schedule Reboot function.
Weekday
Enter the Reboot Time (24-hour format) to enable this function to take effect.
There are two Reboot Plans supported in the AP:
Weekday: select this option to let the device reboot automatically according to the reserved time in one or more days of a week.
Every day: select this option to let the device reboot automatically according to the reserved time every day.
Check one or more days to let the device auto reboot on schedule.
When choosing “Every day” as your reboot plan, the “Weekday” will be grayed out (disabled), which means Every day will auto reboot at the time that you scheduled.
1. This setting will only take effect when the Internet connection is accessible and the GMT time is configured correctly.
2. You must select at least one day when choosing “Weekday” as your reboot plan.
3. When choosing “Every day” as your reboot plan, the “Weekday” will be grayed out
(disabled), which means Every day will auto reboot at the time that you schedule.
-83-
Example of how to configure Schedule Reboot. Please take the following steps:
Before configured schedule reboots, please ensure the Internet connection is accessible and the GMT time is configured correctly according to NTP Settings page.
Step 1. Select the Schedule Reboot Setting checkbox.
Step 2. Enter the Reboot Time (24-hour format) to enable this function to take effect. For example, if you want this function to work at 23:00 every Sunday, choose "Weekday" in the Reboot Plan field.
Figure 5-62 Schedule Reboot - Example
Step 3. Click the “Apply Changes” button to take this function effect.
5.7.6 Denial of Service (DoS)
The Wireless Router can prevent specific DoS attacks from entering your network. A "Denial-of-Service" (DoS) attack is characterized by an explicit attempt by hackers to prevent legitimate users of a service from using that service.
Choose menu “Management Denial-of-Service” to configure the settings of DoS attack prevention. After the configuration, please click the “Apply Changes” button to save the settings.
-84-
The page includes the following fields:
Figure 5-7-6 Denial of Service
Object
Enable DoS Prevention Check to enable DoS function.
Description
User may set other related configurations about DoS below
-85-
5.7.7 LOG
Choose menu “Management Log” to configure the settings of system log. You can check the box of the items you want to record it in the log. After the configuration, please click the “Apply” button to save the settings.
Figure 5-63 System Log
The page includes the following fields:
Object
Enable Log
System all
Wireless
Enable Remote Log
Log Server IP Address
Refresh
Clear
Description
Check to enable log function.
Check this option to display all the system logs.
Check this option to display only the logs related to wireless module.
Enable this option if you have a syslog server currently running on the LAN and wish to send log messages to it.
Enter the LAN IP address of the Syslog Server.
Click this button to update the log.
Click this button to clear the current log.
-86-
5.7.8 Upgrade Firmware
This page allows you upgrade the Access Point firmware to new version. Please note, do not power off the device during the upload because it may crash the system.
Choose menu “Management Upgrade Firmware” to upgrade the firmware of the WMC251-1W-2T-150.
Select the new firmware file downloaded from the IFS website and then click “Upload” button to upgrade it.
The page includes the following fields:
Figure 5-64 Upgrade Firmware
Object
Firmware Version
Select File
Description
Display the current firmware version of the AP.
Browse and select file you want to upgrade and press Upload to perform upgrade.
Please wait till the related information is shown on the screen after
upgrade is finished.
Do not disconnect the Wireless AP from your management PC (the PC you use to configure the device) or power off it during the upgrade process; otherwise, it may be permanently damaged. The Wireless AP will restart automatically when the upgrade process, which takes several minutes, to complete.
5.7.9 Save/Load Setting
Choose menu “Management Save/Load Setting” to back up or reset the configuration of the
WMC251-1W-2T-150.
Once you have configured the Wireless AP the way you want it, you can save these settings to a configuration file on your local hard drive that can later be imported to your Wireless AP in case the device is restored to factory default settings.
-87-
The page includes the following fields:
Figure 5-65 Save/Reload Settings
Object Description
Save Settings to File Click the “Save…” button to back up the configuration of the
WMC251-1W-2T-150 and then save the “config.dat” in your computer.
Load Settings from File Select the configuration file of the WMC251-1W-2T-150 and then click the
“Upload” button to reload the configuration back into the
WMC251-1W-2T-150.
Reset Settings to
Default
Click the “Reset” button to reset all settings of the WMC251-1W-2T-150 to factory default.
Factory Default Settings:
User Name: admin
Password: admin
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.0.253
DHCP: Disabled
SSID: WMC251-1W-2T-150
Wireless Security: None
To activate your settings, you need to reboot the Wireless AP after you reset it.
-88-
5.7.10 Password
To ensure the Wireless AP’s security, you will be asked for your password when you access the Wireless AP’s
Web-based Utility. The default user name and password are “admin”. This page will allow you to add or modify the user name and password.
Choose menu “Management Password” to change the user name and password which is inputted to access the web UI of the WMC251-1W-2T-150.
Figure 5-66 Password Setup
The page includes the following fields:
Object
User Name
Description
Enter user name.
Input password for this user. New Password
Confirmed Password Confirm password again.
For the sake of security, it is highly recommended that you change default login password and user name.
-89-
5.7.11 Logout
To logout the WMC251-1W-2T-150, please select “Logout” from the left-side menu. Then, click “OK” to logout.
Figure 5-67 Logout
-90-
Chapter 6. Quick Connection to a Wireless Network
In the following sections, the default SSID is configured to “default”.
6.1 Windows XP (Wireless Zero Configuration)
Step 1: Right-click on the wireless network icon displayed in the system tray
Figure 6-1 System Tray – Wireless Network Icon
Step 2: Select [View Available Wireless Networks]
Step 3: Highlight and select the wireless network (SSID) to connect
(1) Select SSID [default]
(2) Click the [Connect] button
Figure 6-2 Choose a wireless network
-91-
Step 4: Enter the encryption key of the Wireless AP
(1) The Wireless Network Connection box will appear
(2) Enter the encryption key that is configured in section 5.4.3
(3) Click the [Connect] button
Figure 6-3 Enter the network key
Step 5: Check if “Connected” is displayed
Figure 6-4 Choose a wireless network -- Connected
Some laptops are equipped with a “Wireless ON/OFF” switch for the internal wireless LAN. Make sure the hardware wireless switch is switched to “ON” position.
-92-
6.2 Windows 7 (WLAN AutoConfig)
WLAN AutoConfig service is built-in in Windows 7 that can be used to detect and connect to wireless network.
This built-in wireless network connection tool is similar to wireless zero configuration tool in Windows XP.
Step 1: Right-click on the network icon displayed in the system tray
Figure 6-5 Network icon
Step 2: Highlight and select the wireless network (SSID) to connect
(1) Select SSID [default]
(2) Click the [Connect] button
Figure 6-6 WLAN AutoConfig
If you will be connecting to this Wireless AP in the future, check [Connect automatically].
Step 4: Enter the encryption key of the Wireless AP
-93-
(1) The Connect to a Network box will appear
(2) Enter the encryption key that is configured in section 5.4.3
(3) Click the [OK] button
Figure 6-7 Type the network key
Figure 6-8 Connecting to a Network
Step 5: Check if “Connected” is displayed
-94-
Figure 6-9 Connected to a Network
-95-
6.3 Mac OS X 10.x
In the following sections, the default SSID is configured to “default”.
Step 1: Right-click on the network icon displayed in the system tray
The AirPort Network Connection menu will appear
Figure 6-10 Mac OS – Network icon
Step 2: Highlight and select the wireless network (SSID) to connect
(1) Select and SSID [default]
(2) Double-click on the selected SSID
Figure 6-11 Highlight and select the wireless network
Step 4: Enter the encryption key of the Wireless AP
(1) Enter the encryption key that is configured in section 5.4.3
(2) Click the [OK] button
-96-
Figure 6-12 Enter the Password
If you will be connecting to this Wireless AP in the future, check [Remember this
network].
Step 5: Check if the AirPort is connected to the selected wireless network.
If “Yes”, then there will be a “check” symbol in the front of the SSID.
Figure 6-13 Connected to the Network
-97-
There is another way to configure the MAC OS X Wireless settings:
Step 1: Click and open the [System Preferences] by going to Apple > System Preference or Applications
Figure 6-14 System Preferences
Step 2: Open Network Preference by clicking on the [Network] icon
Figure 6-15 System Preferences -- Network
-98-
Step 3: Check Wi-Fi setting and select the available wireless network
(1) Choose the AirPort on the left-menu (make sure it is ON)
(2) Select Network Name [default] here
If this is the first time to connect to the Wireless AP, it should show “Not network selected”.
Figure 6-16 Select the Wireless Network
-99-
6.4 iPhone / iPod Touch / iPad
In the following sections, the default SSID is configured to “default”.
Step 1: Tap the [Settings] icon displayed in the home screen
Figure 6-17 iPhone – Settings icon
Step 2: Check Wi-Fi setting and select the available wireless network
(3) Tap [General] \ [Network]
(4) Tap [Wi-Fi]
If this is the first time to connect to the Wireless AP, it should show “Not Connected”.
Figure 6-18 Wi-Fi Setting
-100-
Figure 6-19 Wi-Fi Setting – Not Connected
Step 3: Tap the target wireless network (SSID) in “Choose a Network…”
(1) Turn on Wi-Fi by tapping “Wi-Fi”
(2) Select SSID [default]
Figure 6-20 Turn on Wi-Fi
Step 4: Enter the encryption key of the Wireless AP
(1) The password input screen will be displayed
(2) Enter the encryption key that is configured in section 5.4.3
(3) Tap the [Join] button
-101-
Figure 6-21 iPhone -- Enter the Password
Step 5: Check if the device is connected to the selected wireless network.
If “Yes”, then there will be a “check” symbol in the front of the SSID.
Figure 6-22 iPhone -- Connected to the Network
-102-
Appendix A: Troubleshooting
If you find the AP is working improperly or stop responding to you, please read this troubleshooting first before contacting the dealer for help. Some problems can be solved by yourself within a very short time.
Scenario Solution
The AP is not responding to me when I want to access it by Web browser. a. Please check the connection of the power cord and the
Ethernet cable of this AP. All cords and cables should be correctly and firmly inserted to the AP. b. If all LED on this AP is off, please check the status of power adapter, and make sure it is correctly powered. c. You must use the same IP address section which AP uses. d. Are you using MAC or IP address filter? Try to connect the AP by another computer and see if it works; if not, please reset the AP to the factory default settings
(pressing ‘reset’ button for over 7 seconds). e. If you did a firmware upgrade and this happens, contact your dealer of purchase for help. f. If all the solutions above don’t work, contact the dealer for help.
I can’t get connected to the
Internet. a. Go to ‘Status’ -> ‘Internet Connection’ menu on the router connected to the AP, and check Internet connection status. b. Please be patient, sometimes Internet is just that slow. c. If you’ve connected a computer to Internet directly before, try to do that again, and check if you can get connected to Internet with your computer directly attached to the device provided by your Internet service provider. d. Check PPPoE / L2TP / PPTP user ID and password entered in the router’s settings again. e. Call your Internet service provider and check if there’s something wrong with their service. f. If you just can’t connect to one or more website, but you can still use other internet services, please check
URL/Keyword filter. g. Try to reset the AP and try again later. h. Reset the device provided by your Internet service provider too. i. Try to use IP address instead of host name. If you can use IP address to communicate with a remote server, but can’t use host name, please check DNS setting.
-103-
I can’t locate my AP by my a. ‘Broadcast ESSID’ set to off? wireless device. b. Both two antennas are properly secured. c. Are you too far from your AP? Try to get closer. d. Please remember that you have to input ESSID on your wireless client manually, if ESSID broadcast is disabled.
File downloading is very slow or breaks frequently. a. Are you using QoS function? Try to disable it and try again. b. Internet is slow sometimes. Please be patient. c. Try to reset the AP and see if it’s better after that. d. Try to know what computers do on your local network. If someone’s transferring big files, other people will think
Internet is really slow. e. If this never happens before, call you Internet service provider to know if there is something wrong with their network.
I can’t log into the web management interface; the password is wrong.
The AP becomes hot a. Make sure you’re connecting to the correct IP address of the AP! b. Password is case-sensitive. Make sure the ‘Caps Lock’ light is not illuminated. c. If you really forget the password, do a hard reset. a. This is not a malfunction, if you can keep your hand on the AP’s case. b. If you smell something wrong or see the smoke coming out from AP or A/C power adapter, please disconnect the AP and power source from utility power (make sure it’s safe before you’re doing this!), and call your dealer of purchase for help.
-104-
Appendix B: Frequently Asked Questions
Q1: How to set up the AP Client Connection
Topology:
Step 1. Use static IP in the PCs that are connected with AP-1(WMC251-1W-2T-150, Site-1) and AP-2 (Client,
Site-2). In this case, Site-1 is “192.168.1.100”, and Site-2 is “192.168.1.200”.
-105-
Step 2. In AP-1, go to “Wireless Basic Settings” to configure it to AP Mode. Then, configure the following wireless parameters for your wireless network.
1) Network ID (SSID) : set to a unique value
2) Channel: set to a fixed one or auto (suggested set to fixed channel).
-106-
Step 3. Go to “Wireless Security” to configure the security setting.
Step 4. In AP-2, modify the default IP to the same IP range but different from AP-1.
In this case, the IP is changed to 192.168.1.252.
-107-
Step 5. In AP-2, configure it in “Client” mode.
-108-
Step 6. Go to “Wireless Site Survey” to find the AP-1. Then, select it and click “Next”.
Step 7. Configure the Encryption and Pre-Shared Key which must be the same as AP-1. Then click “Connect”.
Step 8. Check “Add to Wireless Profile” and click “Reboot Now” to apply the setting.
Step 9. Go to “Management Status” to check the connection state should be “Connected”.
-109-
Step 10. Use command line tool to ping each other to ensure the link is successfully established.
From Site-1, ping 192.168.1.200; and in Site-2, ping 192.168.1.100.
Step 11. Configure the TCP/IP settings of Site-2 to “Obtain an IP address automatically”.
-110-
Step 12. Use command line tool to ping the DNS (e.g. Google) to ensure the Site-2 can access internet through the wireless connection.
The attention of the following hints should be paid:
1) The encryption method must be the same as that of both sites if configured.
2) Both sites should be Line-of-Sight.
3) For the short distance connection less than 1km, please reduce the "RF Output Power" of both sites to half or lower.
-111-
Q2: How to setup the WDS Connection
Topology:
Step 1. Use static IP in the PCs that are connected with WMC251-150-1(Site-1) and WMC251-150-2(Site-2), in this case, Site-1 is “192.168.1.100”, and Site-2 is “192.168.1.200”.
-112-
Step 2. In AP-1, go to “Wireless Basic Settings” to configure it to “WDS” Mode. Then, set the channel number to a fixed one.
-113-
Step 3. Go to “Wireless WDS Settings” to configure the AP-2’s MAC address.
In AP-1’s WDS Setting, configure AP-2’s MAC address.
Step 4. If you select “Reboot Later”, you can click “Set Security” to continue to configure the encryption and security key of the WDS connection. Then, click “Apply Changes” to apply the setting.
Step 5. In AP-2, modify the default IP to the same IP range but different from AP-1.
In this case, the IP is changed to 192.168.0.252.
-114-
Step 6. In AP-2, configure it to “WDS” mode and set the channel to the fixed one which is the same as AP-1.
-115-
-116-
Step 7. Go to “Wireless WDS Settings” to configure the AP-1’s MAC address.
In AP-1’s WDS Setting, configure AP-2’s MAC address.
Step 8. If you select “Reboot Later”, you can click “Set Security” to continue to configure the encryption and security key of the WDS connection.
Step 9. Click “Apply Changes” to apply the settings.
-117-
Step 10. Use command line tool to ping each other to ensure the link is successfully established.
From Site-1, ping 192.168.0.200; and in Site-2, ping 192.168.0.100.
The attention of the following hints should be paid:
1) The encryption method and channel must be the same for both sites.
2) Both sites should be Line-of-Sight.
3) For the short distance connection less than 1km, please reduce the "RF Output Power" of both sites to half or lower.
-118-
EC Declaration of Conformity
English
Hereby, IFS Technology Corporation, declares that this Outdoor Wireless AP is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Lietuviškai
Česky
Společnost IFS Technology Corporation, tímto prohlašuje, že tato Outdoor Wireless AP splňuje základní požadavky a další příslušná ustanovení směrnice 1999/5/EC.
Magyar
Dansk
Deutsch
Eestikeeles
Ελληνικά
Español
Français
Italiano
Latviski
IFS Technology Corporation, erklærer herved, at følgende udstyr Outdoor Wireless AP overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF
Malti
Hiermit erklärt IFS Technology Corporation, dass sich dieses Gerät Outdoor Wireless AP in
Übereinstimmung mit den grundlegenden
Anforderungen und den anderen relevanten
Vorschriften der Richtlinie 1999/5/EG befindet".
(BMWi)
Nederlands
Polski
Käesolevaga kinnitab IFS Technology
Corporation, et see Outdoor Wireless AP vastab
Euroopa Nõukogu direktiivi 1999/5/EC põhinõuetele ja muudele olulistele tingimustele.
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ , IFS Technology
Corporation,
ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ Outdoor
Wireless AP
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ
ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ
ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ
Por medio de la presente, IFS Technology
Corporation, declara que Outdoor Wireless AP cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE
Par la présente, IFS Technology Corporation, déclare que les appareils du Outdoor Wireless AP sont conformes aux exigences essentielles et aux autres dispositions pertinentes de la directive
1999/5/CE
Con la presente , IFS Technology Corporation, dichiara che questo Outdoor Wireless AP è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva
1999/5/CE.
Português
Slovensky
Slovensko
Suomi
Svenska
Ar šo IFS Technology Corporation, apliecina, ka
šī Outdoor Wireless AP atbilst Direktīvas
1999/5/EK pamatprasībām un citiem atbilstošiem noteikumiem.
Šiuo IFS Technology Corporation,, skelbia, kad
Outdoor Wireless AP tenkina visus svarbiausius
1999/5/EC direktyvos reikalavimus ir kitas svarbias nuostatas.
A gyártó IFS Technology Corporation, kijelenti, hogy ez a Outdoor Wireless AP megfelel az 1999/5/EK irányelv alapkövetelményeinek és a kapcsolódó rendelkezéseknek.
Hawnhekk, IFS Technology Corporation, jiddikjara li dan Outdoor Wireless AP jikkonforma malħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC
Hierbij verklaart , IFS Technology orporation, dat
Outdoor Wireless AP in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG
Niniejszym firma IFS Technology Corporation, oświadcza, że Outdoor Wireless AP spełnia wszystkie istotne wymogi i klauzule zawarte w dokumencie „Directive 1999/5/EC”.
IFS Technology Corporation, declara que este
Outdoor Wireless AP está conforme com os requisitos essenciais e outras disposições da
Directiva 1999/5/CE.
Výrobca IFS Technology Corporation, týmto deklaruje, že táto Outdoor Wireless AP je v súlade so základnými požiadavkami a ďalšími relevantnými predpismi smernice 1999/5/EC.
IFS Technology Corporation, s tem potrjuje, da je ta Outdoor Wireless AP skladen/a z osnovnimi zahtevami in ustreznimi določili Direktive 1999/5/EC.
IFS Technology Corporation, vakuuttaa täten että
Outdoor Wireless AP tyyppinen laite on direktiivin
1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Härmed intygar, IFS Technology Corporation, att denna Outdoor Wireless AP står i
överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
-119-

Public link updated
The public link to your chat has been updated.
Advertisement