1080p UPCONVERTING HDMI
1080p UPCONVERTING HDMI
DVD PLAYER
D V D 3300
DVD3300
INSTRUCTION MANUAL
1-11
WARNINGS
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
To reduce the risk of electric shock, do not open the cabinet. No user serviceable parts are inside. Refer servicing to
qualified personnel.
This appliance uses a Laser System. To prevent direct exposure to the laser beam do not open the cabinet. Visible and
invisible laser radiation is present when the cabinet is open. Avoid direct exposure and do not stare into the beam.
Batteries should not be exposed to excessive heat such as direct sunlight, fire, or other heat sources.
Caution: Do not expose this appliance to dripping or splashing liquids. Do not put objects filled with liquid, such as vases on
or near the appliance.
Caution: To turn this appliance off completely, the POWER cord must be unplugged from the wall outlet. The power cord must
be easily accessible at all times.
•
•
•
•
•
•
CAUTION
DO NOT OPEN
THE LIGHTNING FLASH WITH
ARROWHEAD SYMBOL, WITHIN AN
EQUILATERAL TRIANGLE, IS INTENDED
WARNING: TO REDUCE THE RISK OF
THE EXCLAMATION POINT WITHIN AN
ELECTRIC SHOCK, DO NOT REMOVE THE
EQUILATERAL TRIANGLE IS INTENDED TO
TO ALERT THE USER TO THE
PRESENCE OF NON-INSULATED
FRONT OR REAR COVER. NO USER
ALERT THE USER TO THE PRESENCE OF
SERVICEABLE PARTS ARE INSIDE. REFER
IMPORTANT OPERATING AND
"DANGEROUS VOLTAGE" WITHIN THE
PRODUCT'S ENCLOSURE THAT MAY BE
SERVICING TO QUALIFIED SERVICE
MAINTENANCE (SERVICING)
PERSONNEL.
INSTRUCTIONS IN THE LITERATURE
OF SUFFICIENT MAGNITUDE TO
ACCOMPANYING THE APPLIANCE.
CONSTITUTE A RISK OF ELECTRIC
SHOCK TO PERSONS.
FCC WARNINGS
WARNING: Changes or modifications to this unit not expressly approved in this manual could void the user’s authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT SAFETY INSTRUCTIONS
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third grounding prong. The wide blade and/or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete
outlet.
Protect the POWER cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way,
such as POWER-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
S3125A
QUICK GUIDE FOR HDMI FUNCTION
1. Please check to see if your TV set has a HDMI video input.
2. If your TV set has a HDMI video input then connect the DVD player to the TV set using an HDMI cable
(not included). Switch on the DVD player and TV set. The DVD Player output will automatically be
adjusted from the default video output of 480i to a higher-resolution setting to match that of your TV
screen, 720p, 1080i, or 1080p. The TV screen will now show the "ETEC" logo. Press the H D MI button
on the remote control of the DVD player and you can change the high-resolution setting of the DVD
player to, 720p, 1080i, or 1080p. Once the high-resolution setting of the DVD player changed, the
high-resolution setting on the TV screen image is automatically changed.
IMPORTANT NOTICE
Front and Back Panels. ..................................................................................1
Front Panel. ..................................................................................................1
Back Panel.. ................................................................................................1
Remote Control... ....................................................................................... 2
Operating the Remote Control.... .................................................................... 3
Functions.......... ........................................................................................ 4-7
System Setup..................... ................................................................... . 8-10
MP3 Function .......... ................................................................................... 10
JPEG Files..... ................... ......................................................................... 10
Troubleshooting .........................................................................................11
DVD3300
1.LED DISPLAY
2.REMOTE CONTROL SENSOR
3.OPEN / CLOSE
4.PLAY / PAUSE
5.STOP
6.POWER
D V D 3300
AC 90-240V~50/60Hz
15W
CONFORMS T O
UL STD 60065
CERTIFIED T O
CSA STD C22.2
No. 60065
1. AUDIO output
use to connect both the
right and left channels
AC 90-240V~50/60Hz
15W
2.VIDEO output
3.COAXIAL output
4.HDMI connector
16:9 / 4:3
16:9/4:3
DVD3300
Battery Installation
1. Push down and out on the battery
compartment cover to remove it.
2. Insert the two "AAA" batteries into the battery
compartment of the remote control, making
sure the + and - signs on the batteries and the
inside of the battery compartment match up.
3. Replace the battery compartment cover.
Notes:
Do not mix batteries from different
manufacturers, or old with new.
If the remote control will not be used for an
extended period of time, remove the batteries
to prevent damage-causing corrosion.
Remove the dead batteries immediately to
prevent damage-causing corrosion.
If battery leakage occurs, wipe the battery
liquid from inside the battery compartment,
and then replace both batteries.
Always replace both batteries at the same time,
using new, fully charged batteries.
The life expectancy of batteries may vary
depending on amount of use.
Notes:
Do not direct the remote sensor toward any
light source, such as direct sunlight or strong
fluorescent light as it may cause the unit not to
operate correctly.
When other remote controls are used nearby or
when the remote is used near equipment using
infrared rays, interference may occur.
Placing an object on the remote control may cause
it to inadvertently depress a button, changing a
function and shortening battery life.
Do not cover the front of the DVD receiver
with tinted glass, as it may cause interference
with normal operation of the controller.
Make sure there is no solid objects between
the remote control and the remote sensor .
This could prevent the unit from receiving
the signal.
Do not spill water or put wet items on the
remote control.
Using the Remote Control
Point the remote control at the remote sensor
on the DVD receiver. When the signal is
received from the remote, the unit will function
accordingly.
The remote will operate up to approximately 16'
from the remote sensor at an angle of around
30' in each direction.
BATTERIES
INCORRECT USE OF BATTERIES MAY
CAUSE THEM TO LEAK, CORRODE,
OR EX-PLODE.
To play a DVD video disc:
Turn on the TV set and select the A/V mode.
1. Press the POWER button on front panel,
DISC LOADING appears on screen.
Note:
It is possible to damage a disc if it is not placed
correctly on the guides in the disc tray. This may
also cause the DVD player to malfunction. Do
not force or place anything other than a 5" DVD
or CD onto the disc tray.
Never move the DVD player during playback,
as this may cause damage to the disc as well as
the player. To open and close the disc tray, only
use the OPEN / CLOSE key found on both the
remote control and on the unit's front panel.
If there is no disc in the player, NO DISC will
show on the screen
Press the PLAY / PAUSE
button.
2. Press the OPEN / CLOSE button.
The disc tray will open.
5. PREV / NEXT playback
Press the PREV or NEXT buttons to play the
previous or next track. To resume normal playback,
press PLAY / PAUSE button
3. Place the disc on the disc tray, be sure
content (Wide-screen, Full-screen) side is face
down on the tray.
4. Press OPEN / CLOSE button to close the tray.
The disc tray will close and the disc type will appear
in the upper-left-hand corner of the screen.
Once the player has read the disc, the unit
automatically will begin playback.
Press NEXT button
Screen Display
REV
While a disc is playing, the status of various
functions may be checked, such as the tile,
track number, and several time categories.
1. Press the DISPLAY button once and the title
appears along with the chapter and how much
time has played.
DISPLAY
To activate either function, simply press the
FWD or REV buttons on the remote.
The speed changes each time the button is
presse. To resume normal playback, press
the PLAY / PAUSE button.
2. Press the DISPLAY button again and the
remaining time for that particular title appears.
Stop playback
1. Press the STOP button to end the function and
the TV screen will show the Stop icon. With some
disc formats like DVD, the player can recall the
place in the movie where Stop was pressed, and
resume play from that location.
2. Press PLAY / PAUSE to resume playback from
the location where the disc was stopped or from
the beginning of the disc.
3. Press STOP twice to stop completely.
3. Press the DISPLAY button again and the
total elapsed time for that particular chapter
appears.
STOP
4. Press the DISPLAY button again and the
total remaining time for that particular chapter
appears.
PLAY/PAUSE
Slow Motion
This DVD player has the ability to play discs in
slow motion in either forward or reverse direction.
Each time the SLOW button is pressed, the forward
speed will slow to 1/2 speed, to 1/4, to 1/8, to 1/16,
and back to normal. In reverse, the speed will also
slow from 1/2 speed, to 1/4, to 1/8, to 1/16, and back
to normal. To resume normal playback at anytime,
press the PLAY / PAUSE button.
5. Press the DISPLAY button again and the
display turns off.
Frame-By-Frame Playback
1. While in the Play mode, press STEP continuously
to move forward in the video frame by frame.
2. Press PLAY / PAUSE resume normal playback.
1/2
Audio-L & Audio-R
Language
The default audio setup is STEREO, press
Audio-L , and the sound will be output from Left
channel only, Press Audio-R , and the sound
will be output from Right channel only.
Press Audio-L or Audio-R again, sound will
return back to Stereo.
The unit has the capability to show movies in one
of eight languages.
1. Press the LANGUAGE button. The language
menu will appear. Select the desired language
by pressing the LANGUAGE button.
Subtitles
The DVD Player has the capability to display
subtitles in any of 32 different languages.
1. Press the SUBTITLE button. The subtitle
menu will appear. Select the desired language
by pressing the SUBTITLE button.
Note:
The disc being played must be multi-language
encoded.
Locating A Title
DVD discs are normally divided into titles, which are
then sub-divided into chapters. A Specific title or chapter
can easily be located. Specific titles can be found using
the title menu function if the disc contains a title menu,
or through its unique title number.
2. To remove the subtitles from view, press
the SUBTITLE button until they disappear .
Title Function Menu
1. Press the TITLE button. The title menu will appear
on the TV screen.
2. Press the appropriate scroll button to select the
desired title. A title may also be located by pressing
its assigned number with the number buttons.
3. Press the ENTER button. This will start playback
from chapter 1 of the selected title.
Note: The disc being played must be
multi-subtitle encoded.
Camera Angle
The ability to change the camera angle allows
the viewer to play director and watch a movie
from different perspectives.
1. Press the ANGLE button on the remote
control. With each press, the camera angle
changes.
2. The button may be pressed only when the
flashing angle icon appears in the unit's display
panel.
Note:
Some discs do not respond to this function. If different
instructions appear on the TV screen, follow those
instructions. The instructions given here describe
the basic procedure. Procedures may vary depending
on the content of the DVD disc.
A-B repeat
Press "A-B" once to set a start-point, press again to
set an end point and complete the setting. The
selected section A-B will be repeated. The third press
will cancel this function.
A-B
Note:
The camera angle may be changed only in discs
with multi-angle capability encoded.
AB
PBC function
With the PB C function on, choosing a song
on a CD can only be done when at the main
menu. With the PBC function off, song
selections can be made by entering the
number of the song selection with the
number buttons.
PBC
ZOOM
A picture maybe enlarged up to four times during
either playback or slow motion through the unit's zoom
function. Press the ZOOM button once and it enlarges
the image 2x, press a second time and the image
enlarges 3x. A third press enlarges the image 4x.
A fourth press, shrinks the enlarged image by 1/2x ,
a fifth press shrinks the image 1/3x, a sixth press
shrinks the image 1/4x. To return to normal-size
image, press the ZOOM button a seventh time.
Enlargement takes place in the center of the picture.
Volume and Mute
Repeat Play
This DVD receiver allows repeated playback of
specific titles, chapter/ tracks, or segments. It
even allows switching between two items that
are being repeated,
The volume on this DVD player is easily controlled
with the remote control by pressing either the VOL +
button to raise the volume or the VOL- button to
lower it. By pressing the MUTE button, no audio
will be heard. To return the audio, press the MUTE
button again.
1. Select the item to repeat.
2. Press the REPEAT button.
Program
This function allows you to program the desired
order of play for specific tracks. Press the
PROG button, and the Program menu will appear
on the screen. Set the programs play order using the
number buttons. Then scroll to Start on the menu.
Press the ENTER button to begin program play.
To exit from the program play mode, press the
PROG button again.
DVD Menu Setup
The repeat mode changes each time
the REPEAT button is pressed (i.e.,from title
repeat to chapter repeat, all repeat, to repeat off.)
Press the SETUP button on the remote control and
the main menu will appear .
1. After accessing the setup menu, press the
scroll button up or down to select a desired Item.
Once an item is selected, press the PLAY / PAUSE
button to confirm your entry and then you will
have access to the Sub-directory.
2. Use the left or right scroll buttons to move
the pointer and the up or down scroll buttons
to select the desired option. Once an item is
selected, press the ENTER button to confirm
your selection.
General Setup
This option is used to setup the following
format and functions: TV screen format,
video functions, DVD settings, language,
parental controls, and others.
OSD Language
Language
Video
Audio
:English
Subtitle
:English
MPEG4 Subtitle
:WesternEuropean
Audio
:English
DVD menu
:English
Rating
ASPECT RATIO
There are two kinds of Aspect Ratio, 4:3 & 16:9
which can be selected according to the disc
format & TV set.
VIEW MODE
There are four choices for viewing video:
Fill: Full screen.
Original: Seen according to the contents of
the DVD.
Auto Fit: This is the DEFAULT setting. Auto
Fit will adjust the screen image automatically
Pan Scan: Will automatically edit and show a
Wide screen or other format movie/video as a
Full screen image.
Misc
Language
Language
OSD Language:
There are 3 languages to select from: English,
French and Spanish.
SUBTITLE:
When playing DVD discs, the player can
support: English, French, and Spanish
subtitles. Subtitles can be set to Automatic
or OFF
MPEG4 SUBTITLE:
When playing MPEG4 discs, the player can
support Western European.
AUDIO:
When playing DVD, MPEG4, or VCD discs, the
player can support English, French and Spanish.
DVD MENU:
When playing DVD, MPEG4, or VCD discs,
the player can support English, French and
Spanish.
Video setup
Video
Audio
Aspect Ratio
Audio
:Fill
View Mode
:Original
TV System
:Auto Fit
Video Out
:Pan Scan
HD Resolution
Rating
Misc
TV SYSTEM
This unit is specifically made for the United
States market and will only operate on the
NTSC system.
Language
Aspect Ratio
View Mode
Video
TV System
:NTSC
Video Out
Audio
HD Resolution
Rating
Misc
Follow the directions displayed in "Setup",
and press the remote control buttons based
on the TV Screen display and VIDEO will be
setup.
Language
Video
Aspect Ratio
VIDEO OUTPUT
Use remote control to select the output you
desire.
:16:9
View Mode
:Fill
TV System
:NTSC
Video Out
:HD
HD Resolution
:Auto
Language
Aspect Ratio
View Mode
Video
TV System
Video Out
Audio
Rating
Rating
Misc
Misc
HD Resolution
: HD
HD:
This is only achieved by using a HDMI cable
(not included).
Language
Video
HD RESOLUTION:
Using the HDMI video output requires the use
of a HDMI cable (not included). Your TV set
must must also support high-definition video
as well.
You can select Auto, 480p/576p, 720p, 1080i,
1080p to make the picture much clearer via
the HDMI cable.
Language
Audio
Rating
Parental Control
Rating
Set Password
Misc
SET PASSWORD:
The default password is 0000, after this correct
password is entered, you can then change the
password to one of your choice. Your password
is needed to change the Parental Control
settings.
Aspect Ratio
View Mode
Video
Audio
1.Kid Safe
2.G
3.PG
4.PG-13
5.PG-R
6.R
7.NC-17
8.Adult
TV System
Video Out
:Auto
Brightness
:480p/576p
Sharpness
:720p
HD Resolution
:1080i
:1080p
HD Jpeg mode
Misc
MISC Setup
USE THE DEFAULT SETTINGS:
During use, if you want to return to the factory
default settings, please select USE DEFAULT
SETTINGS, and the player will automatically
return to the factory settings.
Audio Setup
Language
Includes the setup of speakers and Dolby
Digital.
Video
Audio
Language
Rating
Video
Misc
Audio
Digital Output
:PCM
Rating
Misc
DIGITAL OUTPUT
Connect the COXIAL jack on the rear panel to an
External Amplifier unit. Select the PCM setting
and the output signal will be digital 5.1 Channel
PARENTAL CONTROL
To restrict the viewing of certain movie ratings,
Parental Controls can be accessed on this menu.
In order to set or change these settings, the password
must first be entered. After entering the password,
make sure the password is then set to OFF on the
menu, then you can set / change Parental Controls.
Use Default Settings
OPERATION OF MP3 FUNCTION
MP3 is an audio compression mode using
Level 3 of the international standard MPEG.
The audio signal is compressed in a rate of
12:1. A MP3 disc can contain over 600 minutes
of music that rivals Compact Discs in sound
quality.
Files Menu of MP3 play
When playing a MP3 disc, 2 file menus can be
selected by pressing the PROG button: 1) Folder
List and 2) File List.
1. FOLDER LIST
Display the menu first, then press the UP / DOWN,
LEFT / RIGHT arrows and ENTER button to select
the subdirectory and music.
2.FILE LIST
This menu is where you may select the files (or
song numbers) to be played by pressing UP /
DOWN, LEFT / RIGHT arrow buttons combined
with ENTER button. The number buttons and
ENTER can also be used to make the play selection.
If a track number entered, is incorrect,
the screen will display "INPUT INVALID".
Play Modes
There are 4 kinds of play modes: FOLDER,
SINGLE, REPEAT ONE, REPEAT FOLDER.
Press the REPEAT button to make available
the 4 modes:
1. FOLDER: play the entire music menu in order.
2. SINGLE: play a single-track number .
3. REPEAT ONE: play a single-track number
repeatedly.
4. REPEAT FOLDER: play the entire music
menu repeatedly.
JPEG is the most efficient image compression
format and is widely used for photo / picture
storage.
Even when pictures are compressed 15-20
times, they still maintain an excellent quality.
The JPEG format is also supported by most
picture processing software. The JPEG file
uses less storage space and is easy to use.
This DVD player can read JPEG formatted
picture CD discs.
1.Place a photo disc in the DVD player and
menu will appear
2.Press the number buttons of the selection
you want to view.
3. Press PLAY button to view.
Using the Menu To Select Photos
1. Press PLAY / PAUSE button to view the photo on the
screen.
2. Press STOP to end viewing.
3. When in STOP mode, you can return to the
upper menu by selecting the top file item on
the right side of the screen and pressing
PLAY / PAUSE button.
Other functions:
1. When playing JPEG images. This DVD
player allows the pause, play, repeat, and
browse functions.
2. When playing JPEG images, press the
RESUME button to see different formats of
photo display.
3. Press VOL+ and VOL - buttons to select
pictures.
4. To zoom in on the image, press the ZOOM
button. Pressing the ZOOM button again will
return the picture to normal.
5. When the zoom is on, press the Fast
Forward or Fast Reverse to zoom in or out
on the image.
6. When the zoom is off, pressing the direction
arrows will cause the image to turn over
(reverse).
TROUBLE-SHOOTING
This handy trouble-shooting guide is provided
to save you time if you experience any problems
with this DVD player. If the problem is not listed
or if the provided solution does not correct the
problem, please call our customer support
department.
Possible Problems and Solutions
No Power
1. Check to ensure that the power plug is
securely connected to the power outlet and
that the outlet is in working condition (test
outlet by CAREFULLY plugging another
electrical item in to it)
No Sound
1. Check the connection between the DVD player
and the TV set, amplifier, or any other unit it is
connected to.
2. Check to ensure the TV and amplifier are in
the correct mode.
No Picture
1. Check the connection between the DVD
player and the TV set or any other unit it is
connected to.
2.Check to make sure TV is turned on.
Disc D oes Not Play
1.Check to make sure the disc is loaded
correctly label side facing up on disc tray.
2.Check that disc is clean from dirt, dust,
fingerprints, and smudges.
3.Check to ensure the disc is inserted between
the guides on the tray.
4.Check to see if the Parental Lock function is on.
5.Make sure disc is for use in region ONE.
Remote Does Not Work.
1. Check batteries; possibly replace.
2. Check to ensure there aren't any obstacles
between the remote sensor on the unit's front
panel and the remote control.
3.Be sure the remote is aimed at the remote
sensor.
Divided Picture
1.Check that disc is clean and has no scratches.
2. This DVD player is controlled by a
microcomputer, which may need to be reset.
To reset, unplug the unit, wait 30 seconds,
then turn the player back on.
MP3 Discs Don't Play
1. Use a different program to re-burn the disc,
as the program may not be MP3 compatible
with the player.
2. Use a newer edition of MP3 software such
as "Audio station 4", "Easy CD Creator", etc.
3. Make sure MP3 file is not encoded with a
variable bit rate, such as provided by Real
Networks.
LIMITED 90-DAY WARRANTY
We warrant this product to be free from defects in material and workmanship under normal use
for a ninety-day period from the original date of purchase from an authorized ETEC dealer.
We will replace the unit free of charge should it become defective under this warranty,
providing you, the original purchaser, have your original dated sales receipt.
To obtain warranty service or replacement within the ninety-day warranty period, please return
the product with all parts and accessories along with your original dated store receipt to the
original place of purchase and the unit will be exchanged at no charge. It is not necessary to
contact the manufacturer for warranty replacement.
Our Customer Support Center is available Monday - Saturday (10:00AM to 7:00PM EST) for
technical assistance or troubleshooting. To contact us, please call 1-855-994-3832.
This warranty applies only under conditions of normal use.
This warranty does not cover any product which has been subject to damage due to an act of
nature, misuse, neglect, accident, abuse, commercial use, or modification of, or to, any part of
the product, including the antenna. Damage to any external media such as DVD & CD discs,
and/or USB or other memory devices are not covered nor is the cost incurred in shipping the
unit for warranty repair or exchange. Under no circumstances shall ETEC be liable for any loss
(direct, indirect, incidental, foreseen, unforeseen, special or consequential) or for any damage
arising out of, or in connection with, the use of this product.
UNDER NO CIRCUMSTANCES WILL ETEC BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
This warranty does not cover re-manufactured, refurbished, or repaired units, or any products
sold 'As Is'.
This warranty is valid only to the original purchaser of the Product in the United States and
Canada and grants specific legal rights.
Schoenfeld International Inc and ETEC
5001 American Boulevard West
Suite 275
Bloomington, MN 55437
©Schoenfeld International Inc, 2013
PN: DVD3300 Rev 1.4V September, 2013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement