D:\\MDC protocol\\MDC\271\256\274\255\\MDC_Sync

D:\\MDC protocol\\MDC\271\256\274\255\\MDC_Sync
SEC- VD- DSW Multiple Display Control - 0008
Ver. 0. 68
2012- 09- 20
Multiple Display Control Protocol
for SyncMaster
460UT(n)-2
550Dx(n)
460MX-3,400MX-3,320MX-3
320TX-3
400DX-3,460DX-3,700DX-3
400UX-3,460UX-3
320BX,400BX,460BX
UD55A,UD46A, OL46B
MDC_SyncMaster_460UTn-2_550DXn_Protocol_Ver-068-eng
Copyright © 2003 2010 Samsung Electronics Co., Ltd
SEC- VD- DSW Multiple Display Control - 0008
Copyright notice
This document is Copyright © Samsung Electronics, Co. - all rights reserved.
「This document is a technical asset of Samsung Electronics, Co. and using or copying
this material without the authorization from the technical data management group is strictly
prohibited..」
Contact Information
Display S/W Group, VD Business Division
Samsung Electronics Co., Ltd
Address : 416, Maetan-3Dong, Paldal-Gu,
Suwon City, Kyungki-Do, Korea
442-742
Telephone : 82-31-277-1715
E-mail
: [email protected]
[email protected]
Prepared by : Display S/W, Video Display Division.
Status : Prepared
Subject : Technical Writer, Programmer, Developer
Outline : Protocol type document of Multiple Display Control 1.0
1
History :
Version
Date
Content
Prepared by
0.5
2010.06.12
Make New Document for 2010 LFD
(460UT(n)-2 , 550DX(n))
(refer "MDC_SyncMaster_CXn-2_DXn2_UXn-2_650MP_Protocol_Ver-32eng.pdf")
J.H. Jeong
0.6
2010.07.21
Compared by
Model Number control(0x10)
2010.07.28
New model is added.
"MX-3" series(0x3F)
Display Status Control(
Control(0x0D)
Bright_Sensor is changed.
J.H. Jeong
J.H. Jeong
0.65
2010.08.17
- Connecting method(with RJ45)
- RJ45 Connection Spec.
Taehyeong Kim
0.66
2011.07.01
Add new command (Auto ID set)
Taehyeong Kim
0.67
2011.08.24
Add new command
(VideoWall Direct Setting)
Taehyeong Kim
0.68
2011.08.25
SyncMaster 320TX-3
Add Model
Taehyeong Kim
2011.09.26
Add Models
Taehyeong Kim
2011.11.29
Add Models
Taehyeong Kim
2012.02.15
Add Models
(320BX, 400BX, 460BX)
Taehyeong Kim
2012.09.20
Add Model
(OL46B)
Taehyeong Kim
2
1. INTERFACE
1. 1. Connecting Method
There are 2 available ways of connecting. one is RS232, the other is RJ45.
1) Connecting method(with RS232)
-
As of Figure 1-1, connect RS232-In(9Pin) to Personal Computer, connect the next
TV of Display to be connected from RS232-Out (9Pin).
-
In doing so, each TV or Monitor ID can be given from 0 to 99.
-
ID cannot be given duplicated.
-
When granting ID, it does not need to be given out in the connecting order.
Figure1-1 PC,TV or Monitor connecting method(with RS232)
3
2) Connecting method(with RJ45)
-
There are several ways to connect Personal Computer and TV(or Monitor).
-
As of Figure 1-2, connect Hub and Personal Computer(using Ethernet). connect each
TV of Display to be connected to the Hub.
-
In doing so, each TV or Monitor must have an IP address.
TV or Monitor connected by protocol's IP address must have the same ID with the
protocol's ID.
-
-
Each TV or Monitor ID can be duplicated.
Figure1-2 PC,TV or Monitor connecting method(with RJ45)
4
-
As of Figure 1-3, connect TV and Personal Computer(using Ethernet), connect the
next TV of Display to be connected from RS232-Out (9Pin).
-
In doing so, only TV(connected to Personal Computer) needs an IP address. and each
TV or Monitor ID can be given from 0 to 99.
-
ID cannot be given duplicated.
-
When granting ID, it does not need to be given out in the connecting order.
Figure1-3 PC,TV or Monitor connecting method(with RJ45)
5
1. 2. Connection Spec.
1) RS232 Connection Spec.
-
Interactive communications using RS232.
-
Of RS232 standards, three signals RxD(No.2), TxD(No.3) and GND(No.5) are used →
Refer to Figure 1
-
Limit the distance between devices to less than 4m.
- Currently, out of 9 PIN RS232 terminal, PINS in use are numbers 2, 3 and 5.
-
ID should show hexadecimal value of assigned ID, but ID 0 should be 0xFF.
Every communication will be made in hexadecimals and Checksum is the sum of all
remainings. If it exceeds two digits, for example, it is 11+FF+01+01=112, discard the
number in the first digit like below.
-
example) Power On & ID=0
Header
0xAA
Command
0x11
Header
0xAA
Data Length
ID
Command
0x11
1
Data 1
Power
Data Length
Check
Sum
Data 1
12
1
- If you want to control every mechanism connected with Serial Cable regardless of its
ID, set ID part to "0xFE" and send commands. At the time, each SET will follow
commands but it will not respond with ACK.
→
0xFF
1
Table 2-1 RS232 Network spec
Bits Rate
Data Bits
Parity
Stop Bits
Flow Control
9600 bps
8 bits
None
1 bit
None
6
Figure 2-1
RS- 232 pin out DB- 9 pin used for Asynchronous Data
7
2) RJ45 Connection Spec.
- Interactive communications using RJ45.
- Transmit the MDC protocol using TCP/IP Format. the protocol information is stored
in data area.
- The protocol information format is the same as RS232's.
example) Power On & ID=0
Header
Command
0xAA
0x11
TCP
IP
ID
Data
Length
1
Data1
Power
Checksum
UDP
ICMP
ARP
Hardware Interface(Ethernet, PPP etc. )
Header
Command
0xAA
0x11
TCP
IP
→
0xFF
Data
Length
1
RARP
Data1
1
12
UDP
ICMP
ARP
Hardware Interface(Ethernet, PPP etc. )
RARP
- default ip : 192.168.0.10 PORT : 1515
The RJ45 plug has 8-Pins as below.
Table 2-2 RJ45 plug 8-Pins
-
RJ45 PIN#
1
2
3
4
5
6
7
8
Wire Color(T568A)
White/Green
Green
White/Orange
Blue
White/Blue
Orange
White/Brown
Brown
10Base-T Signal
100Base-TX Signal
Transmit+
TransmitReceive+
Unused
Unused
ReceiveUnused
Unused
1000Base-T Signal
BI_DA+
BI_DABI_DB+
BI_DC+
BI_DCBI_DBBI_DD+
BI_DD-
8
2. Commanding words
No
Command Type
Command
Value Range
-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Status Control
Time Control
On Time Control
Off Time Control
Video Control
Audio Control
RGB Control
PIP Status Control
Maintenance Control
Serial Number Control
Display Status Control
Software Version Control
Auto Motion Plus (550DX(n))
Model Number Control
Power Control
Volume Control
Mute Control
Input Source Control
Picture sizes Control
Direct Channel Control
Screen Mode Control
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x0B
0x0D
0x0E
0x0F
0x10
0x11
0x12
0x13
0x14
0x15
0x17
0x18
22
Screen Size Control
0x19
0 ~ 255
23
24
25
26
27
28
29
30
Red Offset Control
Green Offset Control
Blue Offset Control
MDC Connection Type
Image Retention Free
Contrast Control
Brightness Control
Sharpness Control
0x1A
0x1B
0x1C
0x1D
0x1E
0x24
0x25
0x26
0 ~ 100
0 ~ 100
0 ~ 100
0~1
0~1
0 ~ 100
0 ~ 100
0 ~ 100
-
0~1
0 ~ 100
0~1
-
9
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
Color Control
Tint Control
Red Gain Control
Green Gain Control
Blue Gain Control
Treble Control
Bass Control
Coarse Control
Fine Control
H-Position Control
V-Position Control
Auto Power Control
Clear Menu Control
Remote Control
RGB Contrast Control
RGB Brightness Control
PIP On/Off Control
Auto Adjustment Control
Color Tone Control
Color Temperature Control
PIP Source Control
Main-PIP Swap Control
PIP Size Control
PIP Locate Control
Fan Speed Setting
User Auto Color Control
Sound Select Control
Standby Control
Video Picture Position & Size
Pixel Shift Control
Video Wall Control
Auto Lamp Control
Manual Lamp Control
Safety Screen Run Control
0x27
0x28
0x29
0x2A
0x2B
0x2C
0x2D
0x2F
0x30
0x31
0x32
0x33
0x34
0x36
0x37
0x38
0x3C
0x3D
0x3E
0x3F
0x40
0x41
0x42
0x43
0x44
0x45
0x47
0x4A
0x4B
0x4C
0x4F
0x57
0x58
0x59
0 ~ 100
0 ~ 100
0 ~ 100
0 ~ 100
0 ~ 100
0 ~ 100
0 ~ 100
0~1
0~1
0~1
0~1
0~1
0
0~1
0 ~ 100
0 ~ 100
0~1
0
0~4
0 ~ 10
-
0~1
-
0~4
0 ~ 100
0~1
0~1
0~2
-
0 ~ 100
0~6
10
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
Safety Screen Control
Video Wall Mode Control
Safety Lock
Button Lock (Panel Lock)
Channel Up/Down
OSD On/OFF
P. Mode Control
S. Mode Control
NR Mode Set
PC Color Tone Control
Auto AutoAdjustment Enable/Disable
All Keys Lock
SRS TSXT Control
Film Mode
Signal Balance
SB Gain
SB Red Gain
SB Green Gain
SB Blue Gain
SB Sharpness
Panel On Time
Video Wall On
Temperature Control
Brightness Sensor
Dynamic Contrast
Safety Screen On
Video Wall User Control
Model Name
VideoWall Direct Setting
Fan Control(Manual/Auto)
Energy Saving
HDMI Black Level Control
Gamma Control
Reset Control
Ambient Brightness Sensor
(460UT(n)-2)
0x5B
0x5C
0x5D
0x5F
0x61
0x70
0x71
0x72
0x73
0x75
0x76
0x77
0x78
0x79
0x7A
0x7E
0x7B
0x7C
0x7D
0x7F
0x83
0x84
0x85
0x86
0x87
0x88
0x89
0x8A
0x8B
0x8F
0x92
0x94
0x96
0x9F
0xA1
0~1
0~1
0~1
0~1
0~4
0~1
0~3
0~1
0~1
0~1
0~1
0~1
0 ~ 100
0 ~ 100
0 ~ 100
0 ~ 100
0 ~ 100
-
0~1
0 ~ 125
0~1
0~1
1 ~5
0 ~ 1
0 ~ 1
0 ~ 1
0 ~ 3
0 ~ 3
-
11
100
101
102
103
104
105
106
107
108
109
RJ45 setting refresh
OSD Type Display Control
Timer1 Control
Timer2 Control
Timer3 Control
Clock Control
Holiday Add/Delete Control
Holiday Get Control
Panel On/Off
Auto ID set
0xA2
0xA3
0xA4
0xA5
0xA6
0xA7
0xA8
0xA9
0xF9
0xFD
1
-
0~1
-
"-" indicates multiple setting items-refer to "2.1. Command Detailed Explanation" for more
details.
12
2. 1. Command Detailed Explanation
* Status Control
● Function
Personal Computer shows current setting condition of TV / Monitor.
● Get Status
Header
0xAA
Command
0x00
ID
Header
0xAA
Command
0xFF
ID
Val 3
Val 4
Val 5
Header
0xAA
Command
0xFF
ID
Data Length
0
Check
Sum
● Ack
Data Length Ack/Nak
9
'A'
r-CMD
0x00
Val 6
Val 7
Check
Val 1
Power
Val 2
Volume
Mute
Input Aspect N Time NF F Time NF Sum
Power : Power code to be set on TV / Monitor
Volume : Volume value code ( 0 ~ 100 ) to be set on TV / Monitor
Mute : Mute code to be set on TV / Monitor
Input : Input Source code to be set on TV/Monitor
Aspect : Image Size code to be set on TV/Monitor
N Time NF : OnTime ON/OFF value of time to set TV/Monitor(old type Timer)
F Time NF : OffTime ON/OFF value of time to set TV/Monitor(old type Timer)
→ It was supported for old type Timer. Now, It is always 0x00.
● Nak
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
0
1
r-CMD
0x00
Val 1
ERR
Check
Sum
Check Sum Error
etc.
13
* Video Control (ATV, DTV, AV, S- Video, Component, HDMI Only)
● Function
Personal Computer shows the screen condition of TV / Monitor.
● Get Video Status
Header
0xAA
Command
0x04
ID
Header
0xAA
Command
0xFF
ID
Val 3
Val 4
Val 5
Data Length
0
Check
Sum
● Ack
Data Length Ack/Nak
0x0A
'A'
Val 6
Val 7
r-CMD
0x04
Val 8
Val 1
Val 2
Contrast Brightness
Check
Sum
Sharpness Color
Tint ColorTone ColorTemp 0
Contrast, Brightness, Sharpness, Color, Tint, ColorTone, ColorTemp :
Same as above
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x04
Val 1
ERR
Check
Sum
14
* Audio Control
● Function
Personal Computer shows the sounds condition of TV / Monitor.
● Get Audio Status
Header
0xAA
Command
0x05
ID
Header
0xAA
Command
0xFF
ID
Val 3
Check
Header
0xAA
Command
0xFF
Data Length
0
Check
Sum
● Ack
Data Length Ack/Nak
0x05
'A'
r-CMD
0x05
Val 1
Val 2
Val 1
Check
Sum
Treble
Bass
Balance Sum
Treble, Bass, Balance : Same as above
● Nak
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x05
ERR
15
* RGB Control (PC, BNC, DVI Only)
● Function
Personal Computer shows screen condition of TV / Monitor.
● Get Video Status
Header
0xAA
Command
0x06
ID
Header
0xAA
Command
0xFF
ID
Val 3
Val 4
Header
0xAA
Command
0xFF
Data Length
0
Check
Sum
● Ack
Val 5
Data Length Ack/Nak
0x0A
'A'
Val 6
Val 7
r-CMD
0x06
Val 8
Val 1
Val 2
Contrast Brightness
Check
ColorTone ColorTemp 0 Red Gain Green Gain Blue Gain Sum
Contrast, Brightness, ColorTone, ColorTemp,
ColorTemp, Red, Green, Blue : Same as above
● Nak
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x06
Val 1
ERR
Check
Sum
16
* PIP Status Control
● Function
The PC displays the PIP settings of a TV or monitor.
● Get the PIP Status
Header
0xAA
Command
0x07
ID
Header
0xAA
Command
0xFF
ID
Val 3
Val 4
Data Length
0
Checksum
● Ack
Data Length Ack/Nak
6
'A'
r-CMD
0x07
Val 1
Val 2
Val 1
Checksu
m
P.Size P.Source
Checksu
m
0
0
P.Size: The PIP size code set for the TV or monitor.
0x00
0x06
0x08
0x04
0x05
0x09
PIP Off
Large
Small
Double 1
Double 2
Double 3
P.Source: The PIP source code set for the TV or monitor.
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR: The error code indicating which error occurred.
r-CMD
0x07
ERR
17
* Maintenance Control
● Function
Personal Computer shows maintenance state of TV / Monitor.
● Get Maintenance Status
Header
0xAA
Command
0x08
ID
Command
0xFF
ID
Data Length
0
Check
Sum
● Ack
Header
0xAA
Val 3
Val 4
Val 5
Data Length Ack/Nak
0x15
Val 6
'A'
Val 7
r-CMD
0x08
Val 1
Power
Val 8
Val 9
Val 2
P.Size
Val 10
P.Source LMax_H LMax_M LMax_AP LMaxValue LMin_H LMin_M LMin_AP
Val 11
LMinValue
Val17
Val 12
Val 13
Val 18
Val19
Val 14
Val 15
LampValue ScreenInterval ScreenTime ScreenType
Val 16
V.Wall
Check
Sum
V.WallFormat V.WallDivid V.WallSet
Power : Power code set on TV / Monitor
P.Size : P.Size value code set on TV / Monitor
P.Source : Source value code set on TV / Monitor
LMax_H : Auto Lamp Max Time Hour (1 ~ 12) set on TV / Monitor
LMax_M : Auto Lamp Max Time Minute (0 ~ 59) set on TV / Monitor
LMax_AP : Auto Lamp Max Time AM/PM set on TV / Monitor
LMaxValue : Auto Lamp Max value (0 ~ 100) set on TV / Monitor
LMin_H : Auto Lamp Min Time Hour (1 ~ 12) set on TV / Monitor
LMin_M : Auto Lamp Min Time Minute (0 ~ 59) set on TV / Monitor
LMin_AP : Auto Lamp Min Time AM/PM set on TV / Monitor
LMinValue : Auto Lamp Min value (0 ~ 100, 0xFF) set on TV / Monitor
LampValue : Manual Lamp Control value (0 ~ 100, 0xFF) set on TV / Monitor
ScreenInterval : Safety Screen Interval (Per Hour, 0(0ff)~10) set on TV / Monitor
ScreenTime : Safety Screen Time (Per Second, 0(off) ~5) set on TV / Monitor
ScreenType : Safety Screen Type (3 ~ 6) set on TV / Monitor
V.Wall : Video Wall Mode code set on TV / Monitor
V.WallFormat : Video Wall Format code set on TV / Monitor
V.WallDivid : Video Wall Divider code set on TV / Monitor
V.WallSet : Video Wall Set Number code set on TV / Monitor
Caution : If LMinValue is Returned to 0xFF then Auto Lamp Control is OFF.
If LampValue is Returned to 0xFF then Manual Lamp Control is OFF.
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x08
Val 1
ERR
Check
Sum
18
* Serial Number Control
● Function
Personal Computer controls serial number of TV / Monitor.
● Get SerialNum Status
Header
0xAA
Command
0x0B
Data Length
ID
0
Check
Sum
● Ack SerialNum
Header
0xAA
Val 3
Data3
Val 11
Command
0xFF
Val 4
Data4
ID
Val 5
Data5
Val 12
Data Length Ack/Nak
0x14
x14
Val 6
Data6
Val 13
r-CMD
0x0B
'A'
Val 7
Data7
Data8
Data13
Data14
Val 11
Val 12
Val 13
Val 14
Data17
Data17
Val 9
Data9
Val 2
Data2
Val 10
Data10
Val 14
Data12
Data16
Data16
Data1
Val 8
Data11
Data15
Data15
Val 1
Data18
Data18
Check
Sum
Data1 ~ Data14 : Serial Number set on TV / Monitor.
Data15
Data15 ~ Data18
Data18 : Reserved
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x0B
Val 1
ERR
Check
Sum
19
* Display Status Control
● Function
Personal Computer shows display condition of TV / Monitor.
● Get Maintenance Status
Header
0xAA
Command
0x0D
ID
Command
0xFF
ID
Data Length
0
Check
Sum
● Ack
Header
0xAA
Val 3
Val 4
Data Length Ack/Nak
0x08
Val 5
'A'
Val 6
r-CMD
0x0D
Val 1
Val 2
Lamp Temperature
Check
Sum
Bright_Sensor No_Sync Cur_Temp
FAN
Lamp : Lamp Error code (0 : Normal, 1 : Error) to be set on TV / Monitor
Temperature : Temperature Error code (0: Normal, 1: Error) to be set on TV /
Monitor
Bright_Sensor : Brighte Sensor Error code (0: Normal, 1: Error) to be set on
TV/Monitor
Bright_Sensor : Brighte Sensor Error code (0: NONE,
NONE, 1: Error,
Error, 2: NORMAL)
NORMAL) to be
set on TV/Monitor
No_Sync: Sync Error code(0: Normal, 1: Error, No Sync) to be set on TV / Monitor
Cur_Temp : Current temperature of TV / Monitor
FAN : Fan Error code (0 : Normal, 1 : Error) to be set on TV / Monitor
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x0D
Val 1
ERR
Check
Sum
20
* SW Version Control
● Function
Personal Computer shows version information of TV / Monitor.
● Get Version Status
Header
0xAA
Command
0x0E
ID
Command
0xFF
ID
Data Length
0
Check
Sum
● Ack
Header
0xAA
Val 3
Val 4
Data Length Ack/Nak r-CMD
0x14
x14
Val 5
Val 6
Version3 Version4 Version5 Version6
Val 11
Version11
Val 17
Val 12
Version12
Val 18
Val 13
'A'
0x0E
Val 7
Val 8
Val 14
Val 15
Val 1
Val 2
Version1 Version2
Val 9
Val 10
Version7 Version8 Version9 Version10
Val 16
Version13 Version14 Version15 Version16
Version16
Check
Sum
Version17
Version17 Version18
Version18
Version1 ~ Version12
Version12 : Project Info. of TV/Monitor
Version13
Version13 ~ Version18
Version18 : Software version of TV/Monitor
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x06
Val 1
ERR
Check
Sum
21
Auto Motion Plus ( 550Dx)
● Function
Personal Computer controls the Auto Motion Plus that TV / Monitor.
(It is dependent on Product Specifications- 120Hz Panel.)
● Get Auto Motion Plus Status
Header
0xAA
Command
ID
0x0F
Data Length
0x00
Check
Sum
● Set Auto Motion Plus Status
Header
0xAA
Comman
d
Data
Length
ID
0x0F
0x03
Data 1
Data 2
Data 3
Blur Judder
Mode Reductio Reductio
n
n
Check
Sum
Mode :
0x00
0x01
0x02
0x03
0x04
0x05
Off
Clear
Standard
Smooth
Custom
Demo
Blur reduction:
It is only for "Mode: Custom". If "Mode" is not custom, then it is "don't care".
0 ~ 10
Judder reduction:
It is only for "Mode: Custom". If "Mode" is not custom, then it is "don't care".
0 ~ 10
● Ack
Header Comma
nd
0xAA
0xFF
ID
Data Ack/Na r-CMD Val 1
Length
k
0x05
Mode : Same as above
'A'
0x0F
Val 2
Val 3
Blur Judder
Mode Reducti Reducti
on
on
Check
Sum
Blur Reduction, Judder Reduction :
For Set command Type, Data2 and Data3 is same with Set command.
For Get command Type, Date2 and Data2 is LFD's Value.(even If "Mode" is not
custom.)
22
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
0x03
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x0F
Val 1
ERR
Check
Sum
23
* Model Number Control
● Function
Personal Computer shows Model Number of TV / Monitor.
● Get Model Number Status
Header
0xAA
Command
0x10
ID
Data Length
0
Check
Sum
● Ack
Data Length Ack/Nak r-CMD
Header Command
ID
0xAA
0xFF
0x05
'A'
0x10
Species : TV / Monitor 's Panel Type.
0x01
0x02
0x03
Val 1
Val 2 Val 3 Check Sum
Species Model TV
0
PDP
LCD
DLP
Model : TV / Monitor's Model Number.
0x01
0x02
0x03
0x04
0x05
PPM50H2
PPM42S2
PS-42P2ST
PS-50P2HT
SyncMaster 400T
0x06
SyncMaster 403T
0x07
PPM42S3, SPD-42P3SM
0x08
0x09
0x0A
0x0B
PPM50H3, SPD-50P3HM
PPM63H3, SPD-63P3HM
PS-42P3ST
SyncMaster 323T
SyncMaster 403T CT40CS(N)
PPMxxM5x
SyncMaster 320P(n)
SyncMaster 400P(n)
SyncMaster 460P(n)
0x0C
0x0D
0x0E
0x10
0x13
0x14
0x15
SyncMaster 320PX
SyncMaster 400PX(n)
SyncMaster 460PX(n)
SyncMaster 400TX(n)
SyncMaster 570DX
SyncMaster 320DX
0x15
0x16
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
0x20
0x21
0x22
0x23
0x24
SyncMaster 400DX(n)
SyncMaster 460DX(n)
SyncMaster 700DX(n)
SyncMaster 820DX(n)
SyncMaster 460TX(n)
SyncMaster 400UX(n)
SyncMaster
460UX(n)/460DR(n)
SyncMaster 42TS/42PS
SyncMaster P42HP
SyncMaster P50Hn
SyncMaster P50F(n)/P50FP
SyncMaster P63F(n)/P63FP
SyncMaster 320MX(n)
SyncMaster 400CX(n)
SyncMaster 400MX(n)
SyncMaster 400MP(n)
SyncMaster 460CX(n)
SyncMaster 460MP(n)
SyncMaster 520DX(n)
SyncMaster 400UXn-UD
SyncMaster 460UXn-UD
SyncMaster 400FX(n)
SyncMaster 460DRn-A
24
0x25
0x2B
SyncMaster 460UTn-UD
SyncMaster 320MX(n)-2/MP
-2
SyncMaster 460MX(n)2/FP(n)-2
SyncMaster P50HP
0x2D
0x2F
SyncMaster P63FP
SyncMaster 400DXn-S
0x2E
0x30
0x31
SyncMaster 400CX(n)2/460CX(n)-2
0x32
0x33
SyncMaster 400UX(n)-2/
SyncMaster 460UX(n)-2
0x27
0x29
0x35
0x37
SyncMaster 230TSn/230MXn
SyncMaster 400UXn-UD2/460UXn
-UD2
0x26
0x2A
SyncMaster 460UT(n)
SyncMaster 400MX(n)2/FP(n)-2
SyncMaster P42H-2
0x2C
SyncMaster P50FP
SyncMaster 460Rn-S
SyncMaster 460DXn-S
SyncMaster 400DX(n)2/460DX(n)-2/700DX(n)2/820DX(n)-2
0x28
SyncMaster 650MP(n)
0x34
SyncMaster 700DRn
0x36
SyncMaster 460DMn
0x38
SyncMaster P50HP-2
0x39
SyncMaster P63FP-2
0x3A
400EXn
0x3B
460EXn
0x3C
550EXn
0x3D
SyncMaster 460UT(n)-2
0x3E
SyncMaster 550DX(n)
0x40
SyncMaster 520LD
0x42
SyncMaster 460/400 TS(n)-3
UE46A/UE55A /
ME40A/ME46A/ME55A
SyncMaster 460CX(n)-3 /
SyncMaster 400CX(n)-3 /
0x3F
SyncMaster 460MX(n)-3 /
SyncMaster 400MX(n)-3 /
0x41
0x43
SyncMaster 320MX(n)-3
SyncMaster 400BX /
SyncMaster 460/400 UX(n)-3
SyncMaster 460UT(n)-UD2
0x44
SyncMaster UD55A
SyncMaster 320MX-3
0x45
SyncMaster 700DX-3
SyncMaster 820DX-3
SyncMaster 460DR
TV : TV / Monitor's TV support/not support.
0x00
0x01
TV not supported
TV supported
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x10
Val 1
ERR
Check
Sum
25
* Power Control
● Function
Personal Computer turns TV / Monitor power ON/OFF.
● Get Power ON/OFF Status
Header
0xAA
Command
0x11
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Power ON/OFF
Header
0xAA
Command
0x11
ID
1
Power
Check
Sum
Power : Power code to be set on TV / Monitor
1
0
Power ON
Power OFF
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
Power : Same as above
Data Length Ack/Nak
r-CMD
0x11
Data Length Ack/Nak
r-CMD
0x11
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
Power
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
26
* Volume Control
● Function
Personal Computer changes volume of TV / Monitor.
● Get Volume Status
Header
0xAA
Command
0x12
ID
Command
0x12
ID
Command
0xFF
ID
Command
0xFF
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Volume
Header
0xAA
1
Volume
Check
Sum
Volume : Volume value code to be set on TV/Monitor (0 ~ 100 )
● Ack
Header
0xAA
Volume : Same as above
Data Length Ack/Nak
r-CMD
0x12
Data Length Ack/Nak
r-CMD
0x12
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
Volume
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
27
* Mute Control
● Function
Personal Computer turns TV / Monitor mute ON/OFF.
● Get Mute ON/OFF Status
Header
0xAA
Command
0x13
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Mute ON/OFF
Header
0xAA
Command
0x13
ID
1
Mute : Mute code to be set on TV / Monitor
1
0
Mute
Check
Sum
Mute ON
Mute OFF
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
Mute : Same as above
Data Length Ack/Nak
r-CMD
0x13
Val 1
Check
Sum
Data Length Ack/Nak
r-CMD
0x13
Val 1
Check
Sum
3
'A'
Mute
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
28
* Input Source Control
● Function
Personal Computer changes input source of TV / Monitor.
● Get Input Source Status
Header
0xAA
Command
0x14
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Input Source
Header
0xAA
Command
0x14
ID
1
Input
Check
Sum
Input : Input Source code to be set on TV / Monitor
0x14
0x1E
0x18
0x0C
0x04
0x08
0x20
0x1F
0x30
0x40
0x21
0x22
0x23
0x24
0x25
PC
BNC
DVI
AV
S-Video
Component
MagicInfo
DVI_VIDEO
RF(TV)
DTV
HDMI1
HDMI1_PC
HDMI2
HDMI2_PC
DispalyPort
Caution : DVI_
DVI_VIDEO, HDMI1_PC, HDMI2_PC → Get Only
In the case of MagicNet, only possible with models include MagicNet.
In the case of TV, only possible with models include TV.
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
Input : Same as above
Data Length Ack/Nak
r-CMD
0x14
Val 1
Check
Sum
Data Length Ack/Nak
r-CMD
0x14
Val 1
Check
Sum
3
'A'
Input
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
29
* Picture Size Control
● Function
Personal Computer changes Picture Size of TV / Monitor.
Cannot control when Video Wall is on.
● Get Picture Size Status
Header
0xAA
Command
0x15
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Picture Size
Header
0xAA
Command
0x15
ID
1
Aspect
Check
Sum
Aspect : Picture Size code to be set on TV / Monitor
PC1, PC2, DVI,
DVI, BNC,HDMI_PC
0x10
0x18
16 : 9
4 : 3
0x00
0x01
0x04
0x05
0x06
Auto Wide
16 : 9
Zoom
Zoom1
Zoom2
0x31
0x0B
0x0C
0x0D
Wide Zoom
4 : 3
AV, S-VIdeo,
Component,,DVI_Video,HDMI_Video
Component
0x09
Just Scan
Wide Fit
Custom
Caution :For some Image, Picture sizes are not supported depending on some
input signals (720p, 1080i).
For MFM model only possible for those include Europe TV if size is Auto Wide
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
Aspect : Same as above
Data Length Ack/Nak
r-CMD
0x15
Data Length Ack/Nak
r-CMD
0x15
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
Aspect
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
30
* Direct Channel Control (DTV)
Caution : Only works with models include TV.
● Function
Personal Computer can control TV Channel.
● Get Channel
Header
0xAA
Command
0x17
Data Length
ID
0
Check
Sum
● Set Channel
Header
Command
0xAA
0x17
Data 5
Data 6
Header
0xAA
Command
0xFF
Val 3
Val 4
ID
Data
Length Data 1
0x0A
Data 7
Data 2
Data 3
Data 4
Country ATV_DTV AirCable CH_NUM
(Hgh)
Data 8
Data 9
Data 10
CH_NUM Sel_Minor Minor_CH Minor_CH Reserved Reserved
(Low)
(Hgh)
(Low)
Check
Sum
● Ack
ID
Val 5
CH_NUM
AirCable CH_NUM
(Hgh)
(Low)
Val 10
Data Length Ack/Nak
0x0C
Val 6
'A'
r-CMD
0x17
Val 7
Val 1
Val 2
Country ATV_DTV
Val 8
Val 9
Minor_CH Reserved
Sel_Minor Minor_CH
(Hgh)
(Low)
Check
Sum
Reserved
Country : Select the country to be set on TV / Monitor (0 : Korea, 1: USA, .... )
ATV_DTV : Select Analog TV and DTV to be set on TV / Monitor ( 0 : Analog TV,
1: Digital TV)
AirCalbe : Select if TV is cabled or general ( 0 : general, 1: cabled)
CH_NUM : TV channel number to be set on TV / Monitor ( Analog TV : 1 ~ 135 ,
Digital TV : 0 ~ 999)
Sel_Minor : Select minor channel when DTV is to be set on TV / Monitor( 0 : minor
channel not selected. 1: minor channel selected.)
Minor_CH : Select minor channel number when DTV is to be set on TV / Monitor
( 0 ~ 999.)
● Nak
Header
Command
ID
Data Length Ack/Nak
r-CMD
Val 1
Check
31
0xAA
0xFF
3
'N'
ERR : Error code that shows what occurred error is
0x17
ERR
Sum
32
* Screen Mode Control
● Function
Personal Computer changes screen mode of TV
Cannot control when Video Wall is on and only operates when Picture Size is Auto
Wide.
Caution : Only works with models include TV.
● Get Screen Mode Status
Header
0xAA
Command
0x18
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Picture Size
Header
0xAA
Command
0x18
ID
1
ScrMode
Check
Sum
ScrMode : Screen Mode Code to be set on TV / Monitor
0x01
0x04
0x31
0x0B
16 : 9
Zoom
Wide Zoom
4 : 3
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
ScrMode : Same as above
Data Length Ack/Nak
r-CMD
0x18
Data Length Ack/Nak
r-CMD
0x18
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
ScrMode
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
33
* Screen Size Control
● Function
Personal Computer recognizes the screen size of TV / Monitor.
● Get Screen Size Status
Header
0xAA
Command
0x19
ID
Data Length
0
Check
Sum
● Ack
Header
Command
0xAA
0xFF
ID
Data Length Ack/Nak
3
'A'
r-CMD
0x19
Val 1
Screen
Size
Check
Sum
Val 1
Check
Sum
Screen Size : Screen size of TV / Monitor (Range: 0 ~ 255, Unit: Inch)
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x19
ERR
34
* Red Offset Control
● Function
Personal Computer changes R Offset from Signal Control function of TV / Monitor.
※ Signal Control R Offset Control only operates when Signal Balance is on and
current input source is PC and BNC.
● Get Signal Control R Offset Status
Header
0xAA
Command
0x1A
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Signal Control R Gain
Header
0xAA
Command
0x1A
ID
Command
0xFF
ID
Command
0xFF
ID
1
R Offset
Check
Sum
R Offset : R Gain value to be set on TV/Monitor (0 ~ 100)
● Ack
Header
0xAA
R Offset : Same as above
Data Length Ack/Nak
r-CMD
0x1A
Data Length Ack/Nak
r-CMD
0x1A
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
R Offset
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
35
* Green Offset Control
● Function
Personal Computer changes G Offset from Signal Control function of TV / Monitor.
※ Signal Control G Offset Control only operates when Signal Balance is on and
current input source is PC and BNC.
● Get Signal Control G Offset Status
Header
0xAA
Command
0x1B
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Signal Control G Gain
Header
0xAA
Command
0x1B
ID
Command
0xFF
ID
Command
0xFF
ID
1
G Offset
Check
Sum
G Offset : G Offset value to be set on TV/Monitor (0 ~ 100)
● Ack
Header
0xAA
G Offset : Same as above
Data Length Ack/Nak
r-CMD
0x1B
Data Length Ack/Nak
r-CMD
0x1B
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
G Offset
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
36
* Blue Offset Control
● Function
Personal Computer changes B Offset from Signal Control function of TV / Monitor.
※ Signal Control B Offset Control only operates when Signal Balance is on and
current input source is PC and BNC.
● Get Signal Control B Offset Status
Header
0xAA
Command
0x1C
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Signal Control B Offset
Header
0xAA
Command
0x1C
ID
Command
0xFF
ID
Command
0xFF
ID
1
B Offset
Check
Sum
B Offset : B Offset value to be set on TV/Monitor (0 ~ 100)
● Ack
Header
0xAA
B Offset : Same as above
Data Length Ack/Nak
r-CMD
0x1C
Data Length Ack/Nak
r-CMD
0x1C
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
B Offset
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
37
MDC Connection Type
● Function
Personal Computer get MDC Connection Type of TV / Monitor.
(It is dependent on Product Specifications- RJ45 MDC Connection)
(It is Get Commnad Only.)
● Get MDC Connection Status
Header
0xAA
Command
0x1D
ID
Data Length
0x00
Check
Sum
● Ack
Header
Comman
d
0xAA
0xFF
ID
Data
Length
Ack/Nak
r-CMD
0x03
'A'
0x1D
Val 1
Connecti
on Type
Check
Sum
Connection Type
0x00
0x01
RS232C MDC
RJ45 MDC
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
0x03
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x1D
Val 1
ERR
Check
Sum
38
Image Retention Free
● Function
Personal Computer turns TV / Monitor Image Retention Free ON/OFF.
(It is dependent on Product Specifications.)
● Get Image Retention Free Status
Header
0xAA
Command
0x1E
Data Length
ID
0x00
Check
Sum
● Set Image Retention Free Status
Header
Command
0xAA
0x1E
ID
Data Length
Data 1
0x01
Image
Retention
Free
Check Sum
Image Retention Free
0x00
0x01
Off
On
● Ack
Header
Command
0xAA
0xFF
Header
0xAA
Command
0xFF
Data Length
ID
0x03
Ack/Nak r-CMD
'A'
0x1E
Val 1
Image
Retention
Free
Check
Sum
● Nak
ID
Data Length Ack/Nak
0x03
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x1E
Val 1
ERR
Check
Sum
39
* Contrast Control (ATV, DTV, AV, S- Video, Component, HDMI Only)
● Function
Personal Computer changes contrast of TV / Monitor.
● Get Contrast Status
Header
0xAA
Command
0x24
ID
Command
0x24
ID
Command
0xFF
ID
Command
0xFF
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Contrast
Header
0xAA
1
Contrast
Check
Sum
Contrast : Contrast value code to be set on TV/Monitor ( 0 ~ 100 )
● Ack
Header
0xAA
Contrast : Same as above
Data Length Ack/Nak
r-CMD
0x24
Data Length Ack/Nak
r-CMD
0x24
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
Contrast
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
40
* Brightness Control (ATV, DTV, AV, S- Video, Component, HDMI Only)
● Function
Personal Computer changes brightness of TV / Monitor.
● Get Brightness Status
Header
0xAA
Command
0x25
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Brightness
Header
0xAA
Command
0x25
ID
Command
0xFF
ID
Command
0xFF
ID
1
Brightness
Check
Sum
Brightness : Brightness value code to be set on TV/Monitor ( 0 ~ 100 )
● Ack
Header
0xAA
Brightness : Same as above
Data Length Ack/Nak
r-CMD
0x25
Data Length Ack/Nak
r-CMD
0x25
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
Brightness
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
41
* Sharpness Control (ATV, DTV, AV, S- Video, Component, HDMI Only)
● Function
Personal Computer changes sharpness of TV / Monitor의.
● Get Sharpness Status
Header
0xAA
Command
0x26
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Sharpness
Header
0xAA
Command
0x26
ID
Command
0xFF
ID
Command
0xFF
ID
1
Sharpness
Check
Sum
Sharpness : Sharpness value code to be set on TV/Monitor ( 0 ~ 100 )
Caution : Increment level depends on the model's specification.
● Ack
Header
0xAA
Sharpness : Same as above
Data Length Ack/Nak
r-CMD
0x26
Data Length Ack/Nak
r-CMD
0x26
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
Sharpness
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
42
* Color Control (ATV, DTV, AV, S- Video, Component, HDMI Only)
● Function
Personal Computer changes the color of TV / Monitor.
● Get Color Status
Header
0xAA
Command
0x27
ID
Command
0x27
ID
Command
0xFF
ID
Command
0xFF
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Color
Header
0xAA
1
Color
Check
Sum
Color : Color value code to be set on TV/Monitor( 0 ~ 100 )
● Ack
Header
0xAA
Color : Same as above
Data Length Ack/Nak
r-CMD
0x27
Val 1
Check
Sum
Data Length Ack/Nak
r-CMD
0x27
Val 1
Check
Sum
3
'A'
Color
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
43
* Tint Control (ATV, DTV, AV, S- Video, Component, HDMI Only)
● Function
Personal Computer changes tint of TV / Monitor when visual display is NTSC.
Does not operate with PAL signals.
● Get Tint Status
Header
0xAA
Command
0x28
ID
Command
0x28
ID
Command
0xFF
ID
Command
0xFF
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Tint
Header
0xAA
1
Tint
Check
Sum
Tint : Tint value code to be set on TV/Monitor (0 ~ 100 )
R
Tint Value
G
(100 - Tint) Value
● Ack
Header
0xAA
Tint : Same as above
Data Length Ack/Nak
r-CMD
0x28
Val 1
Check
Sum
Data Length Ack/Nak
r-CMD
0x28
Val 1
Check
Sum
3
'A'
Tint
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
44
* Red Gain Control
● Function
Personal Computer changes Red Gain of TV / Monitor.
● Get Red Gain Status
Header
0xAA
Command
0x29
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Red Gain
Header
0xAA
Command
0x29
ID
Command
0xFF
ID
Command
0xFF
ID
1
Red
Check
Sum
Red : Red Gain value code to be set on TV/Monitor ( 0 ~ 100 )
● Ack
Header
0xAA
Red : Same as above
Data Length Ack/Nak
r-CMD
0x29
Val 1
Check
Sum
Data Length Ack/Nak
r-CMD
0x29
Val 1
Check
Sum
3
'A'
Red
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
45
* Green Gain Control
● Function
Personal Computer changes Green Gain of TV / Monitor.
● Get Green Gain Status
Header
0xAA
Command
0x2A
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Green Gain
Header
0xAA
Command
0x2A
ID
Command
0xFF
ID
Command
0xFF
ID
1
Green
Check
Sum
Green : Green Gain value code to be set on TV/Monitor ( 0 ~ 100 )
● Ack
Header
0xAA
Green : Same as above
Data Length Ack/Nak
r-CMD
0x2A
Data Length Ack/Nak
r-CMD
0x2A
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
Green
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
46
* Blue Gain Control
● Function
Personal Computer changes Blue Gain of TV / Monitor.
● Get Blue Gain Status
Header
0xAA
Command
0x2B
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Blue Gain
Header
0xAA
Command
0x2B
ID
Command
0xFF
ID
Command
0xFF
ID
1
Blue
Check
Sum
Blue : Blue Gain value code to be set on TV/Monitor ( 0 ~ 100 )
● Ack
Header
0xAA
Blue : Same as above
Data Length Ack/Nak
r-CMD
0x2B
Val 1
Check
Sum
Data Length Ack/Nak
r-CMD
0x2B
Val 1
Check
Sum
3
'A'
Blue
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
47
* Treble Control
● Function
Personal Computer changes Treble of TV / Monitor.
● Get Treble Status
Header
0xAA
Command
0x2C
ID
Command
0x2C
ID
Command
0xFF
ID
Command
0xFF
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Treble
Header
0xAA
1
Treble
Check
Sum
Treble : Treble value code to be set on TV/Monitor ( 0 ~ 100 )
● Ack
Header
0xAA
Treble : Same as above
Data Length Ack/Nak
r-CMD
0x2C
Data Length Ack/Nak
r-CMD
0x2C
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
Treble
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
48
* Bass Control
● Function
Personal Computer changes Bass of TV / Monitor.
● Get Bass Status
Header
0xAA
Command
0x2D
ID
Command
0x2D
ID
Command
0xFF
ID
Command
0xFF
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Bass
Header
0xAA
Bass : Bass value code ( 0 ~ 100 )
1
Bass
Check
Sum
● Ack
Header
0xAA
Bass : Same as above
Data Length Ack/Nak
r-CMD
0x2D
Val 1
Check
Sum
Data Length Ack/Nak
r-CMD
0x2D
Val 1
Check
Sum
3
'A'
Bass
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
49
* Balance Control
● Function
Personal Computer changes Balance of TV / Monitor.
● Get Balance Status
Header
0xAA
Command
0x2E
ID
Command
0x2E
ID
Command
0xFF
ID
Command
0xFF
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Balance
Header
0xAA
1
Balance
Check
Sum
Balance : Balance value code to be set on TV/Monitor ( 0 ~ 100 )
L
(100 - Balance) Value
R
Balance Value
● Ack
Header
0xAA
Balance : Same as above
Data Length Ack/Nak
r-CMD
0x2E
Data Length Ack/Nak
r-CMD
0x2E
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
Balance
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
50
* Coarse Control (PC, BNC Only)
● Function
Personal Computer adjusts Coarse of TV / Monitor.
● Get Coarse Status
None
● Set Coarse
Header
0xAA
Command
0x2F
ID
Data Length
1
Data 1
Coarse
Check
Sum
Coarse : Coarse Increase/Decrease code to be set on TV/Monitor
1
0
Increase
Decrease
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
Coarse : Same as above
Data Length Ack/Nak
r-CMD
0x2F
Data Length Ack/Nak
r-CMD
0x2F
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
Coarse
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
51
* Fine Control (PC, BNC Only)
● Function
Personal Computer adjusts Fine of TV / Monitor.
● Get Fine Status
None
● Set Fine
Header
0xAA
Command
0x30
ID
Data Length
Fine : Phase Increase/Decrease code
1
0
1
Data 1
Fine
Check
Sum
Increase
Decrease
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
Fine : Same as above
Data Length Ack/Nak
r-CMD
0x30
Val 1
Check
Sum
Data Length Ack/Nak
r-CMD
0x30
Val 1
Check
Sum
3
'A'
Fine
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
52
* H- Position Control (PC, BNC Only)
● Function
Personal Computer adjusts Horizontal Position of TV / Monitor.
● Get H-Position Status
None
● Set H-Position
Header
0xAA
Command
0x31
ID
Data Length
1
Data 1
H-Pos
Check
Sum
H-Pos : H-Position Increase/Decrease code to be set on TV/Monitor
1
0
Move to Right
Move to Left
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
H-Pos : Same as above
Data Length Ack/Nak
r-CMD
0x31
Data Length Ack/Nak
r-CMD
0x31
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
H-Pos
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
53
* V- Position Control (PC, BNC Only)
● Function
Personal Computer adjusts Vertical Position of TV/Monitor.
● Get V-Position Status
None
● Set V-Position
Header
0xAA
Command
0x32
ID
Data Length
1
Data 1
V-Pos
Check
Sum
V-Pos : V-Position Increase/Decrease code to be set on TV/Monitor
1
0
Move Down
Move Up
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
V-Pos : Same as above
Data Length Ack/Nak
r-CMD
0x32
Data Length Ack/Nak
r-CMD
0x32
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
V-Pos
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
54
* Auto Power Control
● Function
Personal Computer adjusts Auto Power Control of TV/Monitor.
● Get Auto Power
Header
0xAA
Command
0x33
ID
Data Length
0x00
Check
Sum
Data Length
Data 1
● Set Auto Power
Header
Command
0xAA
0x33
ID
0x01
Auto
Power
Check
Sum
Auto Power : The Auto Power Control code to set for the TV or monitor
0x00
0x01
Auto Power Off
Auto Power On
● Ack
Header
Command
0xAA
0xFF
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
0x03
'A'
r-CMD
0x33
Val 1
Auto
Power
Check
Sum
Val 1
Check
Sum
● Nak
ID
Data Length Ack/Nak
0x03
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x33
ERR
55
* Clear Menu Control
● Function
Personal Computer removes Menu OSD left in TV / Monitor.
● Get Clear Menu Status
None
● Set Clear Menu
Header
0xAA
Command
0x34
ID
Command
0xFF
ID
Command
0xFF
ID
Clear : 0x00 (Always)
Data Length
1
Data 1
Clear
Check
Sum
● Ack
Header
0xAA
Data Length Ack/Nak
r-CMD
0x34
Val 1
Check
Sum
Data Length Ack/Nak
r-CMD
0x34
Val 1
Check
Sum
3
'A'
Clear
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
56
* Remote Control
● Function
Personal Computer enables/disables IR receiving function of TV/Monitor/
Can operate regardless of whether power is ON/OFF
● Get Remote Status
Header
0xAA
Command
0x36
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Remote Enable/Disable
Header
0xAA
Command
0x36
ID
1
RMC : Power code to be set on TV/Remocon
1
0
RMC
Check
Sum
Remocon Enable
Remocon Disable
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
RMC : Same as above
Data Length Ack/Nak
r-CMD
0x36
Val 1
Check
Sum
Data Length Ack/Nak
r-CMD
0x36
Val 1
Check
Sum
3
'A'
RMC
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
57
* RGB Contrast Control (PC, BNC, DVI Only)
● Function
Personal Computer changes contrast of TV / Monitor when Input Source is PC.
● Get Contrast Status
Header
0xAA
Command
0x37
ID
Command
0x37
ID
Command
0xFF
ID
Command
0xFF
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Contrast
Header
0xAA
1
Contrast
Check
Sum
Contrast : RGB Contrast value code to be set on TV/Monitor ( 0 ~ 100 )
● Ack
Header
0xAA
Contrast : Same as above
Data Length Ack/Nak
r-CMD
0x37
Data Length Ack/Nak
r-CMD
0x37
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
Contrast
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
58
* RGB Brightness Control (PC, BNC, DVI Only)
● Function
Personal Computer changes Brightness when Input Source of TV / Monitor is PC.
● Get Brightness Status
Header
0xAA
Command
0x38
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Brightness
Header
0xAA
Command
0x38
ID
Command
0xFF
ID
Command
0xFF
ID
1
Brightness
Check
Sum
Brightness : RGB Brightness value code to be set on TV/Monitor ( 0 ~ 100 )
● Ack
Header
0xAA
Brightness : Same as above
Data Length Ack/Nak
r-CMD
0x38
Data Length Ack/Nak
r-CMD
0x38
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
Brightness
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
59
* PIP On / Off Control
● Function
The PC turns the PIP function of a TV or monitor on/off.
This does not operate in MagicInfo mode.
● Get the PIP ON/OFF Status
Header
0xAA
Command
0x3C
ID
Data Length Checksu
0
m
Data Length
Data 1
● Set the PIP ON/OFF
Header
0xAA
Command
0x3C
ID
1
PIP
Checksu
m
PIP: The PIP On/Off code to set for the TV or monitor.
1
0
PIP ON
PIP OFF
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
PIP: Same as above.
Data Length Ack/Nak
r-CMD
0x3C
Val 1
Checksu
m
Data Length Ack/Nak
r-CMD
0x3C
Val 1
Checksu
m
3
'A'
PIP
● Nak
Header
0xAA
3
'N'
ERR: The error code indicating which error occurred.
ERR
60
* Auto Adjustment Control (PC, BNC Only)
● Function
Personal Computer controls PC system screen automatically.
● Get Auto Adjustment Status
None
● Set Auto Adjustment
Header
0xAA
Command
0x3D
ID
Command
0xFF
ID
Command
0xFF
ID
Auto : 0x00 (Always)
Data Length
1
Data 1
Auto
Check
Sum
● Ack
Header
0xAA
Data Length Ack/Nak
r-CMD
0x3D
Val 1
Check
Sum
Data Length Ack/Nak
r-CMD
0x3D
Val 1
Check
Sum
3
'A'
Auto
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
61
* Color Tone Control (ATV, DTV, AV, S- Video, Component, HDMI Only)
● Function
Personal Computer changes Color Tone of TV / Monitor.
● Get Color Tone Status
Header
0xAA
Command
0x3E
ID
Data Length
Check
Sum
Data Length
Data 1
0
● Set Color Tone
Header
0xAA
Command
0x3E
ID
1
Color Tone
Check
Sum
Color Tone : Color Tone value code to be set on TV/Monitor ( 0 ~ 4 )
0x00
0x01
0x02
0x03
0x04
0x50
Cool 2
Cool 1
Normal
Warm 1
Warm 2
Off
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
Brightness : Same as above
Data Length Ack/Nak
r-CMD
0x3E
Data Length Ack/Nak
r-CMD
0x3E
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
Color Tone
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
62
* Color Temperature Control
● Function
Personal Computer changes Color Temperature value of TV / Monitor.
Only operates when Color Tone is set to Off.
● Get C_Temp Status
Header
0xAA
Command
0x3F
ID
Header
0xAA
Command
0x3F
ID
0xFE
0xFF
0 ~ 10
3000K
4000K
5000K ~ 15000K
Data Length
0
Check
Sum
Data Length
Data 1
● Set C_Temp
1
C_Temp
Check
Sum
C_Temp : Color Temperature value code to be set on TV/Monitor
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
C_Temp : Same as above
Data Length Ack/Nak
r-CMD
0x3F
Data Length Ack/Nak
r-CMD
0x3F
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
C_Temp
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
63
* PIP Source Control
● Function
The PC changes the PIP source of a TV or monitor.
This only operates for a TV or monitor where PIP is set to On.
This does not operate in MagicInfo mode.
● Get the PIP Source Status
Header
0xAA
Command
0x40
ID
Data Length Checksu
0
m
Data Length
Data 1
● Set the PIP Source
Header
0xAA
Command
0x40
ID
Command
0xFF
ID
Command
0xFF
ID
P.Source
Checksu
m
Data Length Ack/Nak
r-CMD
0x40
Data Length Ack/Nak
r-CMD
0x40
1
P.Source: The input source code to set for the TV or monitor.
Caution : The PIP source swap may not function according to the main source.
● Ack
Header
0xAA
P.Source: Same as above.
3
'A'
Val 1
Checksu
m
Val 1
Checksu
m
P.Source
● Nak
Header
0xAA
3
'N'
ERR: The error code indicating which error occurred.
ERR
64
* Main- PIP Swap Control
● Function
The PC swaps the main and PIP screens.
This does not operate in MagicInfo mode.
● Get the Main-PIP Swap Status
N/A
● Set the Main-PIP Swap
Header
0xAA
Command
0x41
ID
Command
0xFF
ID
Swap: 0x00 (Always)
Data Length
1
Data 1
Swap
Checksu
m
● Ack
Header
0xAA
Data Length Ack/Nak
r-CMD
0x41
Val 1
Data Length Ack/Nak
r-CMD
Val 1
0x41
ERR
3
'A'
Swap
Checksu
m
● Nak
Header
Command
0xAA
0xFF
ID
3
'N'
Checksu
m
ERR: The error code indicating which error occurred.
65
* PIP Size Control
● Function
The PC changes the PIP size of a TV or monitor.
This does not operate in MagicInfo mode.
● Get the PIP Size Status
Header
Command
0xAA
0x42
Data Length
ID
0
Checksu
m
Data Length
Data 1
1
P.Size
● Set the PIP Size
Header
Command
0xAA
0x42
ID
Checksu
m
P.Size: The PIP size code set for the TV or monitor.
0x00
0x06
0x08
0x04
0x05
0x09
PIP Off
Large
Small
Double 1
Double 2
Double 3
● Ack
Header
Command
0xAA
0xFF
Data Length Ack/Nak
ID
3
'A'
r-CMD
Val 1
0x42
P.Size
r-CMD
Val 1
0x42
ERR
Checksu
m
P.Size: Same as above.
● Nak
Header
Command
0xAA
0xFF
Data Length Ack/Nak
ID
3
'N'
ERR: The error code indicating which error occurred.
Checksu
m
66
* PIP Locate Control
● Function
The PC adjusts the PIP position of a TV or monitor.
This does not operate in MagicInfo mode.
● Get the PIP Locate Status
N/A
● Set the PIP Locate
Header
Command
0xAA
0x43
ID
Data Length
Data 1
1
P.Locate
Checksu
m
P.Locate : The PIP Locate Increase/Decrease code to set for the TV or monitor.
0
1
2
3
4
PIP Off(Get Only)
Upper Left
Upper Right
Lower Right
Lower Left
● Ack
Header
Command
0xAA
0xFF
Data Length Ack/Nak
ID
3
'A'
r-CMD
Val 1
0x43
P.Locate
r-CMD
Val 1
0x43
ERR
Checksu
m
P.Locate: Same as above
● Nak
Header
Command
0xAA
0xFF
Data Length Ack/Nak
ID
3
'N'
Checksu
m
ERR: The error code indicating which error occurred.
67
* Fan Speed Setting
● Function
The PC adjusts the Fan Speed of a TV or monitor.
● Get Fan Speed
Header
0xAA
Command
0x44
ID
Data Length
0x00
Check
Sum
Data Length
Data 1
● Set Fan Speed
Header
Command
0xAA
0x44
ID
0x01
FAN
Speed
Check
Sum
FAN Speed : The Fan Speed to set for the TV or monitor.
0 ~ 100
Fan Speed
If you send "Set Fan speed", then "Fan Control" changed "Manual".
(refer "Fan Control" command (0x8F))
● Ack
Header
Command
0xAA
0xFF
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
0x03
'A'
r-CMD
0x44
Val 1
FAN
Speed
Check
Sum
Val 1
Check
Sum
● Nak
ID
Data Length Ack/Nak
0x03
'N'
ERR: The error code indicating which error occurred.
r-CMD
0x44
ERR
68
* User Auto Color(PC, BNC Only)
● Function
The PC adjusts the User Auto Color Control of a TV or monitor.
● Set User Auto Color
Header
Command
0xAA
0x45
ID
Data Length
0x01
Auto Color Cmd : The Auto Color Cmd
0x00
0x01
Data 1
AutoColor
Cmd
Check
Sum
to set for the TV or monitor.
Reset
Auto Color
● Ack
Header
Command
0xAA
0xFF
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
0x03
'A'
r-CMD
0x45
Val 1
AutoColor
Cmd
Check
Sum
● Nak
ID
Data Length Ack/Nak
0x03
'N'
ERR: The error code indicating which error occurred.
r-CMD
0x45
Val 1
ERR
Check
Sum
69
* Sound Select Control
● Function
The PC changes the sound when the PIP of a TV or monitor is set to On.
● Get the Sound Select
Header
Command
0xAA
0x47
Data Length
ID
0
Checksu
m
Data Length
Data 1
● Set the Sound Select
Header
0xAA
Command
ID
0x47
1
S.Selct
Checksu
m
S.Select: The Sound Select code to set for the TV or monitor
1
0
Main
Sub
● Ack
Header
0xAA
Data Length Ack/Nak
Command
0xFF
ID
3
'A'
r-CMD
Val 1
0x47
S.Select
r-CMD
Val 1
0x47
ERR
Checksu
m
S.Select: Same as above.
● Nak
Header
Command
0xAA
0xFF
Data Length Ack/Nak
ID
3
'N'
Checksu
m
ERR: The error code indicating which error occurred.
70
* Standby Control
● Function
The PC adjusts the Standby Control of a TV or monitor.
It is work for PC/DVI/HDMI/DisplayPort.
● Get Standby Setting
Header
0xAA
Command
0x4A
ID
Data Length
0x00
Check
Sum
● Set Standby Setting
Header
Command
0xAA
0x4A
ID
Data Length
0x01
Data 1
Standby
Setting
Check
Sum
Standby Setting : The Standyby Setting code to set for the TV or monitor
0x00
0x01
0x02
Off
On
Auto
● Ack
Header
Command
0xAA
0xFF
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
0x03
'A'
r-CMD
0x4A
Val 1
Standby
Setting
Check
Sum
● Nak
ID
Data Length Ack/Nak
0x03
'N'
ERR: The error code indicating which error occurred.
r-CMD
0x4A
Val 1
ERR
Check
Sum
71
* Video Picture Position & Size (Video Source Only)
● Function
The PC adjusts the Picture Position & Size of a TV or monitor.
It is work for Video Mode(AV, Component, S-Video, DVI/HDMI-TV Timing).
And "Picture Size" is must be zoom1,zoom2, Screen Fit, Custom.
(For detail, plase refer below table.)
Position
Size
Reset
Up Down Left Right
Up Down Left Right
16:9
X
X
X
X
X
X
X
X
X
Zoom1
O
O
O
X
X
X
X
X
X
Zoom2
O
O
O
X
X
X
X
X
X
4:3
X
X
X
X
X
X
X
X
X
Screen Fit
O
O
O
O
O
X
X
X
X
Custom
O
O
O
O
O
O
O
O
O
● Set Video Picture Position & Size
Header
Command
0xAA
0x4B
ID
Data Length
0x02
Data 1
Type
CMD
Data 2
Check
Sum
Direction
CMD
Type CMD: The Standyby Setting code to set for the TV or monitor
0x00
0x01
0x02
Reset
Position
Size
Direction CMD:
It is work for Type CMD Size or Position.
If "Type CMD" is Reset, then "Direction CMD" is not work.
0x00
0x01
0x02
0x03
Down
Up
Left
Right
● Ack
Header
Comma
nd
0xAA
0xFF
ID
Data
Length Ack/Nak
0x04
'A'
r-CMD
Val 1
Val 2
0x4B
Type
CMD
Direction
CMD
Check
Sum
72
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
0x03
'N'
ERR: The error code indicating which error occurred.
r-CMD
0x4B
Val 1
ERR
Check
Sum
73
* Pixel Shift Control
● Function
Personal Computer controls Pixel Shift function of TV / Monitor.
Cannot control when Video Wall is on or when Zoom(0x39) is set or when Input
Signal is VESA Mode in DVI.
● Get Pixel Shift Status
Header
0xAA
Command
0x4C
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Pixel Shift
Header
0xAA
Command
0x4C
ID
0x04
Shift
Data 2
H.Dot
Data 3
V.Line
Data 4
S.Time
Check
Sum
Shift : Pixel Shift On/Off Code to be set on TV/Monitor
Caution : If Shift value is off, H.Dot, V.Line, S.Time values are ignored in TV /
Monitor.
1
0
ON
OFF
H.Dot : Horizontal Dot value code set on TV/Monitor (0 ~ 4)
V.Line : Vertical Line value code set on TV/Monitor (0 ~ 4)
S.Time : Shift Time value code set on TV/Monitor (1 ~ 4)
● Ack
Header
0xAA
Command
0xFF
ID
Val 3
Val 4
Check
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
0x06
'A'
r-CMD
0x4C
Val 1
Val 2
Shift
H.Dot
r-CMD
0x4C
Val 1
Check
Sum
V.Line S.Time Sum
Shift, H.Dot, V.Line, S.Time : Same as above
● Nak
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
ERR
74
* Auto Lamp Control
● Function
Personal Computer sets Auto Lamp Function of TV / Monitor.
When Manual Lamp Control is on, Auto Lamp Control will automatically turn off.
● Get Auto Lamp
Header
0xAA
Command
0x57
Data Length
ID
0
Check
Sum
● Set Auto Lamp
Header
0xAA
Data 5
LMin_H
Command
0x57
Data Length Data 1
ID
Data 6
8
Data 7
LMin_M
Data 2
Data 3
Data 4
Val 1
Val 2
LMax_H LMax_M LMax_AP LMaxValue
Data 8
LMin_AP LMinValue
Check
Sum
● Ack
Header
0xAA
Command
0xFF
ID
Val 3
Val 4
Val 5
Data Length Ack/Nak
0x0A
'A'
r-CMD
0x57
Val 6
Val 7
Val 8
LMax_H LMax_M
Check
Sum
LMax_AP LMaxValue LMin_H LMin_M LMin_AP LMinValue
LMax_H : Auto Lamp Max Time Hour set on TV/Monitor (1 ~ 12)
LMax_M : Auto Lamp Max Time Minute set on TV/Monitor (0 ~ 59)
LMax_AP : Auto Lamp Max Time set on TV/Monitor AM/PM
LMaxValue : Auto Lamp Max Value set on TV/Monitor (0 ~ 100)
LMin_H : Auto Lamp Min Time Hour set on TV/Monitor (1 ~ 12)
LMin_M : Auto Lamp Min Time Minute set on TV/Monitor (0 ~ 59)
LMin_AP : Auto Lamp Min Time set on TV/Monitor AM/PM
LMinValue : Auto Lamp Min Value set on TV/Monitor (0 ~ 100)
Caution: When LMinValue is Returned to 0xFF, Auto Lamp Control is off.
When Dynamic contrast is on, Auto Lamp Control does not operate.
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x57
Val 1
ERR
Check
Sum
75
* Manual Lamp Control
● Function
Personal Computer sets Manual Lamp Function of TV / Monitor.
When Auto Lamp Control is on, Manual Lamp Control will automatically turn off.
● Get Manual Lamp Status
Header
0xAA
Command
0x58
ID
Data Length
0
Check
Sum
● Set Manual Lamp
Header
0xAA
Command
0x58
ID
Command
0xFF
ID
Data Length
1
Data 1
LampValue
Check
Sum
LampValue : Manual Lamp value to be set on TV/Monitor (0 ~ 100)
● Ack
Header
0xAA
Data Length Ack/Nak r-CMD
3
'A'
0x58
Val 1
LampValue
Check
Sum
LampValue : Same as above
Caution : When LampValue is Returned to 0xFF, Manual Lamp Control is off.
● Nak
When Dynamic contrast is on, Manual Lamp Control does not operate.
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x58
Val 1
ERR
Check
Sum
76
* Safety Screen Run Control
● Function
Personal Computer will make Safety Screen function to operate immediately, not by
Timer operation.
● Get Safety Screen Run Status
Header
0xAA
Command
0x59
ID
Data Length
Check
Sum
Data Length
Data 1
0
● Set Safety Screen Run
Header
Command
0xAA
0x59
ID
1
Safety
Screen
Type
Check
Sum
Safety Screen Type : Safety Screen Type to be set on TV/Monitor (1~7)
0x00
0x01
0x02
0x03
0x04
0x06
0x07
Off
Signal Pattern
All White
Scroll
Bar
Eraser
Pixel
Caution : 1(0x01), 2(0x02) only works with PDP models
● Ack
Header
Command
0xAA
0xFF
Data Length Ack/Nak
ID
3
'A'
r-CMD
0x59
Safety Screen Type : Same as above
Val 1
Safety
Screen
Type
Check
Sum
Val 1
Check
Sum
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x59
ERR
77
* SBP Timer Control
● Function
Personal Computer sets Screen Burn Protection Timer of TV/Monitor.
● Get SBP Timer Status
Header
0xAA
Command
0x5B
ID
Data Length
0
Check
Sum
● Set SBP Timer
Header
0xAA
Command
0x5B
ID
Data Length Data 1
3
Data 2
Data 3
Timer T.Period T.Time
Check
Sum
Timer : SBP Timer code to be set on TV/Monitor
0x03
0x04
0x05
0x06
0x09
0x0A
Scroll
Pixel
Bar
Eraser
All White
Pattern
Caution : 9(0x09), 10(0x0A) only works with PDP models
T.Period : SBP Timer Period value code to be set on TV/Monitor
T.Time
((It is dependent on Timer.)
: SBP Timer Time value code set on TV/Monitor.
((It is dependent on Timer.)
Off :
If T.Period is 0 or T.Time is 0, then this is off.
● Ack
Header
0xAA
Command
0xFF
Val 3
Check
Sum
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
5
'A'
r-CMD
0x5B
Val 1
Val 2
Timer
T.Period
Val 1
Check
Sum
T.Time
Timer, T.Period, T.Time : Same as above
● Nak
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x5B
ERR
78
* Video Wall Mode Control
● Function
Personal Computer converts Video Wall Mode of TV / Monitor when Video Wall is
ON.
Only works with TV/Monitor where Video Wall is on.
● Get Video Wall Mode
Header
0xAA
Command
0x5C
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Video Wall Mode
Header
0xAA
Command
0x5C
ID
1
WallMode
Check
Sum
WallMode : Video Wall Mode code to be set on TV/Monitor
1
0
Full
Natural
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
WallMode : same as above
Data Length Ack/Nak
r-CMD
0x5C
Data Length Ack/Nak
r-CMD
0x5C
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
WallMode
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
79
* Safety Lock
● Function
Personal Computer turns Safety Lock function of TV/Monitor On/Off.
Can operate regardless of whether power is on/off.
● Get Safety Lock Status
Header
0xAA
Command
0x5D
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Safety Lock Enable/Disable
Header
0xAA
Lock :
Command
0x5D
ID
1
Lock
Check
Sum
Lock code to be set on TV/Monitor
1
0
On
Off
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
Lock : Same as above
Data Length Ack/Nak
r-CMD
0x5D
Val 1
Check
Sum
Data Length Ack/Nak
r-CMD
0x5D
Val 1
Check
Sum
3
'A'
Lock
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
Lock
80
* Button Lock(Panel Lock)
● Function
Personal Computer turns Panel function Key Lock of TV/Monitor On/OFF.
Can operate regardless of whether power is on/off.
● Get Button Lock Status
Header
0xAA
Command
0x5F
ID
Data Length
0
Check
Sum
● Set Button Lock
Header
0xAA
Button
Command
0x5F
ID
Data Length
1
Data 1
Button
Lock
Check
Sum
Lock : Panel Key Lock On/Off code to be set on TV/Monitor
1
0
Lock
Unlock
● Ack
Header
0xAA
Command
0xFF
ID
Button Lock : Same as above
Data Length Ack/Nak
3
'A'
r-CMD
0x5F
Val 1
Button Lock
Check
Sum
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x5F
Val 1
ERR
Check
Sum
81
* Channel Up/ Down
● Function
Caution : Only works with models include TV.
Personal Computer can control TV Channel.
● Set TV Channel Up/ Down
Header
Command
0xAA
0x61
ID
Data Length
1
Data 1
Channel
Up/Down
Check
Sum
Channel Up/Down: Channel UP or Down to be set on TV / Monitor (0~1)
0
1
Up
Down
● Ack
Header
Command
0xAA
0xFF
Header
Command
ID
Data Length Ack/Nak
Channel Up/Down : Same as above
3
'A'
r-CMD
Val 1
0x61
Channel
Up/Down
r-CMD
Val 1
Check
Sum
● Nak
ID
Data Length Ack/Nak
0xAA
0xFF
3
'N'
ERR : Error code that shows what occurred error is
0x61
ERR
Check
Sum
82
* OSD On/ Off
● Function
Personal Computer turns OSD of TV / Monitor On/Off.
When OSD is on, OSD will be shown on screen
When OSD is off, OSD will not shown on screen at all
● Get OSD Enable Status
Header
0xAA
Command
0x70
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set OSD Enable/Disable
Header
0xAA
Command
0x70
ID
1
OSD
Check
Sum
OSD : OSD On/Off code to be set on TV/Monitor
1
0
OSD On
OSD Off
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
OSD : Same as above
Data Length Ack/Nak
r-CMD
0x70
Val 1
Check
Sum
Data Length Ack/Nak
r-CMD
0x70
Val 1
Check
Sum
3
'A'
OSD
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
83
* P.Mode Control
● Function
Personal Computer changes Picture Mode of TV / Monitor.
● Get PMode Status
Header
0xAA
Command
0x71
ID
Command
0x71
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set PMode
Header
0xAA
1
PMode
Check
Sum
PMode : Picture Mode code to be set on TV/Monitor
Source
AV
S-Video
Component
HDCP
( TV )
PC
BNC
DVI
DisplayPort
( MagicNet )
Data
0x00
0x01
0x02
Mode
Dynamic
Standard
Movie
0x03
Custom
0x50
0x10
0x11
0x12
0x13
0x14
0x15
0x50
Off(Deleted)
Entertain
Internet
Text
Custom
Advertisement
Information
Off(Deleted)
Caution : Dynamic Contrast will not operate in any other mode except Off mode.
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
PMode : Same as above
Data Length Ack/Nak
r-CMD
0x71
Data Length Ack/Nak
r-CMD
0x71
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
PMode
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
84
* S.Mode Control
● Function
Personal Computer changes Sound Mode of TV / Monitor.
● Get SMode Status
Header
0xAA
Command
0x72
ID
Command
0x72
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set SMode
Header
0xAA
1
SMode
Check
Sum
SMode : Sound Mode code to be set on TV/Monitor
Data
0x00
0x01
0x02
0x03
0x04
Mode
Standard
Music
Movie
Speech
Custom
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
SMode : Same as above
Data Length Ack/Nak
r-CMD
0x72
Data Length Ack/Nak
r-CMD
0x72
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
SMode
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
85
* NR Mode Set (ATV, DTV, AV, S- Video, Component, HDMI Only)
● Function
Personal Computer changes Digital NR mode.
● Get NR Mode Status
Header
0xAA
Command
0x73
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set NR Mode
Header
0xAA
Command
0x73
ID
1
NR Mode
Check
Sum
NR Mode : NR Mode On/Off code to be set on TV/Monitor
1
0
NR Mode On
NR Mode Off
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
NR Mode : Same as above
Data Length Ack/Nak
r-CMD
0x73
Data Length Ack/Nak
r-CMD
0x73
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
NR Mode
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
86
* PC Color Tone Control (PC, BNC, DVI Only)
● Function
Personal Computer can change color tone of Monitor.
● Get Color Tone Status
Header
0xAA
Command
0x75
ID
Data Length
Check
Sum
0
● Set Color Tone
Header
0xAA
Command
0x75
ID
Data Length
Data 1
Color Tone
1
Check
Sum
Color Tone : Color Tone value code to set on TV/Monitor (0 ~ 3)
Source
PC
DVI
BNC
Data
0x00
0x01
0x02
0x03
0x50
Mode
Custom
Cool
Normal
Warm
Off
● Ack
Header
0xAA
Command
0xFF
ID
Color Tone : Same as above
Data Length Ack/Nak
3
'A'
r-CMD
0x75
Val 1
Color Tone
Check
Sum
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x75
Val 1
ERR
Check
Sum
87
* Auto AutoAdjustment Enable/ Disable
● Function
Personal Computer can Enable/Disable Auto Adjustment function.
If this value is Disable. then Auto Adjustment is not work.
● Get A.Adjustment Status
Header
0xAA
Command
0x76
Data Length
ID
0
Check
Sum
● Set A.Adjustment
Header
0xAA
Command
0x76
Data Length
ID
1
Data 1
A.Adjustment
Check
Sum
A.Adjustment : Auto Auto Adjustment Enable/Disable Value Code to be set on
TV/Monitor
1
0
Enable
Disable
● Ack
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
A.Adjustment : Same as above
3
'A'
r-CMD
0x76
Val 1
Check
Sum
Val 1
Check
Sum
A.Adjustment
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x76
ERR
88
* All Keys Lock
● Function
Personal Computer turns both REMOCON and Panel Key Lock function on/off.
Can operate regardless of whether power is on/off.
● Get All Key Status
Header
0xAA
Command
0x77
ID
Data Length
0
Check
Sum
● Set All Key Lock/Unlock
Header
0xAA
Command
0x77
ID
Data Length
Data 1
Check
Sum
All Key
1
All Key : Lock On/Off code of every Key to be set on TV/Monitor
1
0
Lock
Unlock
● Ack
Header
0xAA
Command
0xFF
ID
All Key : Same as above
Data Length Ack/Nak
3
'A'
r-CMD
0x77
Val 1
All Key
Check
Sum
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x77
Val 1
ERR
Check
Sum
89
* SRS TS XT Control
● Function
Personal Computer turns SRS TS XT of TV / Monitor on/off.
Can only operate with TV/Monitor that has SRS TS XT function.
● Get SRS TS XT Status
Header
0xAA
Command
0x78
ID
Data Length
0
Check
Sum
● Set SRS TSXT
Header
0xAA
Command
0x78
ID
Data Length
1
Data 1
SRS
Check Sum
SRS : SRS TS XT code to be set on TV/Monitor
1
0
SRS ON
SRS OFF
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
SRS : Same as above
Data Length Ack/Nak
r-CMD
0x78
Val 1
Check
Sum
Data Length Ack/Nak
r-CMD
0x78
Val 1
Check
Sum
3
'A'
SRS
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
90
*
Film Mode Control
● Function
Personal Computer turns Film Mode of TV / Monitor on/off.
● Get Film Mode Status
Header
0xAA
Command
0x79
ID
Data Length
0
Check
Sum
● Set Film Mode
Header
0xAA
Command
0x79
ID
Data Length
1
Data 1
FMode
Check Sum
FMode : Film Mode code to be set on TV/Monitor
1
0
Film Mode ON
Film Mode OFF
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
FMode : Same as above
Data Length Ack/Nak
r-CMD
0x79
Data Length Ack/Nak
r-CMD
0x79
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
FMode
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
91
* Signal Balance ( PC, BNC Only)
● Function
Personal Computer turns Signal Balance of TV / Monitor ON/OFF.
● Get Signal Balance Status
Header
0xAA
Command
0x7A
ID
Data Length
0
Check
Sum
● Set Signal Balance
Header
0xAA
Command
0x7A
ID
Data Length
1
Data 1
SBalance
Check Sum
SBalance : Signal Balance code to be set on TV/Monitor
1
0
Signal Balance ON
Signal Balance OFF
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
SBalance : Same as above
Data Length Ack/Nak
r-CMD
0x7A
Data Length Ack/Nak
r-CMD
0x7A
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
SBalance
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
92
* SB Red Gain ( PC, BNC Only)
● Function
Personal Computer changes Red Gain value of Monitor Signal Balance.
● Get SB Red Gain Status
Header
0xAA
Command
0x7B
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set SB Red Gain
Header
0xAA
Command
0x7B
ID
Command
0xFF
ID
Command
0xFF
ID
1
SB R Gain
Check
Sum
SB R Gain : Phase B value code of Signal Balance to be set on Monitor ( 0 ~ 100 )
● Ack
Header
0xAA
SB R Gain : Same as above
Data Length Ack/Nak
r-CMD
0x7B
Data Length Ack/Nak
r-CMD
0x7B
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
SB R Gain
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
93
* SB Green Gain( PC, BNC Only)
● Function
Personal Computer changes Green Gain value of Monitor Signal Balance.
● Get SB Green Gain Status
Header
0xAA
Command
0x7C
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set SB Green Gain
Header
0xAA
Command
0x7C
ID
Command
0xFF
ID
Command
0xFF
ID
1
SB G Gain
Check
Sum
SB G Gain : Phase B value code of Signal Balance to be set on Monitor ( 0 ~ 100 )
● Ack
Header
0xAA
SB G Gain : Same as above
Data Length Ack/Nak
r-CMD
0x7C
Data Length Ack/Nak
r-CMD
0x7C
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
SB G Gain
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
94
* SB Blue Gain( PC, BNC Only)
● Function
Personal Computer changes Blue Gain value of Monitor Signal Balance.
● Get SB Blue Gain Status
Header
0xAA
Command
0x7D
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set SB Blue Gain
Header
0xAA
Command
0x7D
ID
Command
0xFF
ID
Command
0xFF
ID
1
SB B Gain
Check
Sum
SB G Gain : Phase B value code of Signal Balance to be set on Monitor ( 0 ~ 100 )
● Ack
Header
0xAA
SB B Gain : Same as above
Data Length Ack/Nak
r-CMD
0x7B
Data Length Ack/Nak
r-CMD
0x7C
3
'A'
Val 1
Check
Sum
Val 1
Check
Sum
SB B Gain
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
ERR
95
* SB Sharpness ( PC, BNC Only)
● Function
Personal Computer changes Sharpness value of Monitor Signal Balance.
● Get SBSharpness Status
Header
0xAA
Command
0x7F
ID
Data Length
0
Check
Sum
● Set SBSharpness
Header
0xAA
Command
0x7F
ID
Command
0xFF
ID
Command
0xFF
ID
Data Length
1
Data 1
SBSharpness
Check
Sum
SBSharpness : Signal Balance Sharpness value code to be set on Monitor ( 0 ~ 100 )
● Ack
Header
0xAA
SBSharpness : Same as above
Data Length Ack/Nak
r-CMD
0x7F
Data Length Ack/Nak
r-CMD
0x7F
3
'A'
Val 1
SBSharpness
Check
Sum
● Nak
Header
0xAA
3
'N'
ERR : Error code that shows what occurred error is
Val 1
ERR
Check
Sum
96
* Panel On Time
● Function
Personal Computer shows Panel On Time of TV / Monitor.
● Get Panel On Time Status
Header
0xAA
Command
0x83
ID
Command
0xFF
ID
Data Length
0
Check
Sum
● Ack
Header
0xAA
Data Length Ack/Nak
r-CMD
0x83
Data Length Ack/Nak
r-CMD
0x05
'A'
Val 1
Val 2
PTime_ H PTime_L
Check
Sum
PTime_H : Panel On Time High.
PTime_L : Panel On Time Low.
● Nak
Header
Command
0xAA
0xFF
ID
3
'N'
ERR : Error code that shows what occurred error is
0x83
Val 1
ERR
Check
Sum
97
* Video Wall On
● Function
Personal Computer turns Video Wall of TV / Monitor ON/OFF.
Does not operate in MagicInfo source.
● Get Video Wall On/Off Status
Header
0xAA
Command
0x84
ID
Data Length
0
Check
Sum
● Set Video Wall On/Off
Header
0xAA
Command
0x84
ID
Data Length
1
Data 1
V.Wall_On
Check Sum
V.Wall_On : Video Wall Code to set on TV / Monitor
1
0
Video Wall ON
Video Wall OFF
● Ack
Header
0xAA
Command
0xFF
ID
V.Wall_On : Same as above
Data Length
3
Ack/Nak r-CMD
'A'
0x84
Val 1
V.Wall_On
Check
Sum
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x84
Val 1
ERR
Check
Sum
98
* Temperature Control
● Function
Personal Computer sets the maximum value of TV / Monitor temperature.
Only supports models with Temperature notification function.
● Get Temperature Status
Header
0xAA
Command
0x85
ID
Data Length
0
Check
Sum
● Set Temperature Status
Header
0xAA
Command
0x85
ID
Data Length
1
Data 1
Temperature
Check Sum
Temperature : Temperature code to be set on TV/Monitor
Data
75 ~ 125(℃)
● Ack
Header
0xAA
Command
0xFF
ID
Temperature : Same as above
Data Length
3
Ack/Nak r-CMD
'A'
0x85
Val 1
Temperature
Check
Sum
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x85
Val 1
ERR
Check
Sum
99
* Brightness Sensor
● Function
Personal Computer turns Brightness Sensor of TV / Monitor on/off.
Only supports models with Brightness Sensor.
PDP Model is not available it.
● Get Brightness Sensor ON/OFF Status
Header
0xAA
Command
0x86
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Brightness Sensor ON/OFF
Header
0xAA
Command
0x86
ID
1
BR_Sensor
Check
Sum
BR_Sensor : Brightness Sensor Code to be set on TV/Monitor
1
0
Brightness Sensor ON
Brightness Sensor OFF
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
Data Length Ack/Nak
3
'A'
r-CMD
0x86
Val 1
Check
Sum
Val 1
Check
Sum
BR_Sensor
● Nak
Header
0xAA
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x86
ERR
100
* Dynamic Contrast
● Function
Personal Computer turns Dynamic Contrast of TV / Monitor on/off.
PDP Model is not available it.
● Get Dynamic Contrast ON/OFF Status
Header
0xAA
Command
0x87
ID
Data Length
0
Check
Sum
Data Length
Data 1
● Set Dynamic Contrast ON/OFF
Header
0xAA
Command
0x87
ID
1
DY_Cont
Check
Sum
DY_Cont : Dynamic Contrast code to be set on TV/Monitor
1
0
Dynamic Contrast ON
Dynamic Contrast OFF
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
Data Length Ack/Nak
3
'A'
r-CMD
0x87
Val 1
Check
Sum
Val 1
Check
Sum
DY_Cont
● Nak
Header
0xAA
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x87
ERR
101
* Video Wall User Control
● Function
Personal Computer turns Video Wall function of TV / Monitor on/off.
Does not operate in MagicInfo mode.
● Get Video Wall Status
Header
0xAA
Command
0x89
Data Length
ID
0
Check
Sum
● Set Video Wall
Data Length
Header Command
ID
0xAA
0x89
2
Data 1
Data 2
Wall_Div Wall_SNo
Check
Sum
Wall_Div : Video Wall Divider code set on TV/Monitor
(It is dependent on Product Specifications.)
- 5x5
Video Wall Model :
- 10x10 Video Wall Model :
V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
OFF
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
1
0x11
0x12
0x13
0x14
0x15
0x16
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
0x1E
0x1F
2
0x21
0x22
0x23
0x24
0x25
0x26
0x27
0x28
0x29
0x2A
0x2B
0x2C
0x2D
0x2E
0x2F
3
0x31
0x32
0x33
0x34
0x35
0x36
0x37
0x38
0x39
0x3A
0x3B
0x3C
0x3D
0x3E
0x3F
4
0x41
0x42
0x43
0x44
0x45
0x46
0x47
0x48
0x49
0x4A
0x4B
0x4C
0x4D
0x4E
0x4F
5
0x51
0x52
0x53
0x54
0x55
0x56
0x57
0x58
0x59
0x5A
0x5B
0x5C
0x5D
0x5E
0x5F
6
0x61
0x62
0x63
0x64
0x65
0x66
0x67
0x68
0x69
0x6A
0x6B
0x6C
0x6D
0x6E
0x6F
7
0x71
0x72
0x73
0x74
0x75
0x76
0x77
0x78
0x79
0x7A
0x7B
0x7C
0x7D
0x7E
N/A
8
0x81
0x82
0x83
0x84
0x85
0x86
0x87
0x88
0x89
0x8A
0x8B
0x8C
N/A
N/A
N/A
9
0x91
0x92
0x93
0x94
0x95
0x96
0x97
0x98
0x99
0x9A
0x9B
N/A
N/A
N/A
N/A
H
102
10
0xA1
0xA2
0xA3
0xA4
0xA5
0xA6
0xA7
0xA8
0xA9
0xAA
N/A
N/A
N/A
N/A
N/A
11
0xB1
0xB2
0xB3
0xB4
0xB5
0xB6
0xB7
0xB8
0xB9
N/A
N/A
N/A
N/A
N/A
N/A
12
0xC1
0xC2
0xC3
0xC4
0xC5
0xC6
0xC7
0xC8
N/A
N/A
N/A
N/A
N/A
N/A
N/A
13
0xD1
0xD2
0xD3
0xD4
0xD5
0xD6
0xD7
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
14
0xE1
0xE2
0xE3
0xE4
0xE5
0xE6
0xE7
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
15
0xF1
0xF2
0xF3
0xF4
0xF5
0xF6
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Wall_SNo : TV/Monitor Number code set on TV/Monitor
(It is dependent on Product Specifications.)
- 5x5
Video Wall Model : ( 1 ~ 25 )
Set Number
Data
1
2
0x01
0x02
...
...
24
0x18
0x19
25
0x10 Video Wall Model : ( 1 ~ 100)
1
-
Set Number
Data
1
2
0x01
0x02
...
...
99
0x63
0x64
100
● Ack
Data Length Ack/Nak r-CMD
Header Command
ID
0xAA
0xFF
4
'A'
0x89
Val 1
Val 2
Check
Sum
r-CMD
0x89
Val 1
Check
Sum
Wall_Div Wall_SNo
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
ERR
103
* Model Name Control
● Function
Personal Computer grasps TV / Monitor Model Name and display.
● Get Model Number Status
Header
0xAA
Command
0x8A
Data Length Check S
ID
um
0
● Ack
Header
0xAA
Command
0xFF
ID
Val 3
Val 4
Val 5
Data Length Ack/Nak r-CMD
Length
'A'
Val 6
Val 7
Val 1
Val 2
M_Name1 M_Name2
0x8A
Val 8
Val 9
Val 10
M_Name3 M_Name4 M_Name5 M_Name6 M_Name7 M_Name8 M_Name9 M_Name10
Val 11
Val 12
Val 17
Val ...
M_Name11 M_Name12
Val 13
M_Name13
Val 14
M_Name14
Val 15
Val 16
M_Name15 M_Name16
Check
Sum
M_Name17 M_Name...
M_Name1 ~ M_Name.
M_Name... : TV / Monitor's Model Name.
Length : Length means number of M_Name elements & Ack/Nak & r-CMD.
M_Name1
'S'
M_Name2
'y'
M_Name3
'n'
M_Name4
'c'
M_Name5
'M'
M_Name6
'a'
M_Name7
's'
M_Name8
't'
M_Name9
'e'
M_Name10
'r'
M_Name11
'4'
M_Name12
'0'
M_Name13
'0'
M_Name14
'D'
M_Name15
'X'
M_Name16
'n'
104
* Video Wall Direct User Control
● Function
The PC turns the Video Wall of a TV or monitor on/off.
This does not operate while PIP is operating.
● Get the Video Wall Status
Header
Command
0xAA
0x8B
Data Length
ID
0
Check
Sum
● Set the Video Wall
Header Command
0xAA
Data 5
Input
0x8B
ID
Data Length
5
Data 1
Data 2
Data 3
Data 4
V.Wall_On WallMode Wall_Div Wall_SNo
Check
Sum
V.Wall_On: The Video Wall code to set for the TV or monitor.
1
0
Video Wall ON
Video Wall OFF
WallMode: The Video Wall mode code to set for the TV or monitor.
1
0
Full
Natural
105
Wall_Div: The Video Wall Divider code set for the TV or monitor.
(It is dependent on Product Specifications.)
V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
OFF
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
1
0x11
0x12
0x13
0x14
0x15
0x16
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
0x1E
0x1F
2
0x21
0x22
0x23
0x24
0x25
0x26
0x27
0x28
0x29
0x2A
0x2B
0x2C
0x2D
0x2E
0x2F
3
0x31
0x32
0x33
0x34
0x35
0x36
0x37
0x38
0x39
0x3A
0x3B
0x3C
0x3D
0x3E
0x3F
4
0x41
0x42
0x43
0x44
0x45
0x46
0x47
0x48
0x49
0x4A
0x4B
0x4C
0x4D
0x4E
0x4F
5
0x51
0x52
0x53
0x54
0x55
0x56
0x57
0x58
0x59
0x5A
0x5B
0x5C
0x5D
0x5E
0x5F
6
0x61
0x62
0x63
0x64
0x65
0x66
0x67
0x68
0x69
0x6A
0x6B
0x6C
0x6D
0x6E
0x6F
7
0x71
0x72
0x73
0x74
0x75
0x76
0x77
0x78
0x79
0x7A
0x7B
0x7C
0x7D
0x7E
N/A
8
0x81
0x82
0x83
0x84
0x85
0x86
0x87
0x88
0x89
0x8A
0x8B
0x8C
N/A
N/A
N/A
9
0x91
0x92
0x93
0x94
0x95
0x96
0x97
0x98
0x99
0x9A
0x9B
N/A
N/A
N/A
N/A
10
0xA1
0xA2
0xA3
0xA4
0xA5
0xA6
0xA7
0xA8
0xA9
0xAA
N/A
N/A
N/A
N/A
N/A
11
0xB1
0xB2
0xB3
0xB4
0xB5
0xB6
0xB7
0xB8
0xB9
N/A
N/A
N/A
N/A
N/A
N/A
12
0xC1
0xC2
0xC3
0xC4
0xC5
0xC6
0xC7
0xC8
N/A
N/A
N/A
N/A
N/A
N/A
N/A
13
0xD1
0xD2
0xD3
0xD4
0xD5
0xD6
0xD7
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
14
0xE1
0xE2
0xE3
0xE4
0xE5
0xE6
0xE7
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
15
0xF1
0xF2
0xF3
0xF4
0xF5
0xF6
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
H
Wall_SNo: The TV/Monitor serial number code set for the TV or monitor.
Set Number
Data
1
2
0x01
0x02
...
...
99
0x63
100
0x64
106
Input: The input source code to set for the TV or monitor.
0x14
0x1E
0x18
0x0C
0x04
0x08
0x20
0x1F
0x30
0x40
0x21
PC
BNC
DVI
AV
S-Video
Component
MagicNet
DVI_VIDEO
RF(TV)
DTV
HDMI
● Ack
Header Command
0xAA
Val 3
0xFF
Val 4
Wall_Div Wall_SNo
ID
Data Length Ack/Nak r-CMD
7
Val 5
Input
'A'
0x8B
Val 1
Val 2
V.Wall_ WallMod
On
e
Check
Sum
Check
Sum
● Nak
Header
Command
0xAA
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR: The error code indicating which error occurred.
r-CMD
Val 1
0x8B
ERR
Check
Sum
107
* Fan Control (Manual/Auto)
● Function
The PC adjusts the Fan Control of a TV or monitor.
● Get Fan Control Status
Header
0xAA
Command
0x8F
ID
Data Length
0x00
Check
Sum
Data Length
Data 1
● Set Fan Control
Header
0xAA
Command
0x8F
ID
0x01
FAN
Check
Sum
FAN : Fan Control code to be set on TV/Monitor
0x00
0x01
Fan Control Manual
Fan Control Auto
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
Data Length Ack/Nak
0x03
'A'
r-CMD
0x8F
Val 1
Check
Sum
r-CMD
0x8F
Val 1
Check
Sum
FAN
● Nak
Header
0xAA
Data Length Ack/Nak
0x03
'N'
ERR : Error code that shows what occurred error is
ERR
108
* Energy Saving
● Functio
The PC adjusts the Energy Saving of a TV or monitor.
● Get Energy Saving
Header
0xAA
Command
0x92
ID
Data Length
0x00
Check
Sum
Data Length
Data 1
0x01
Energy
Saving
● Set Energy Saving
Header
Command
0xAA
0x92
ID
Check
Sum
Energy Saving : Energy Saving code to be set on TV/Monitor
0x00
0x01
Energy Saving Off
Energy Saving On
● Ack
Header
Command
0xAA
0xFF
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
0x03
'A'
r-CMD
0x92
Val 1
Energy
Saving
Check
Sum
Val 1
Check
Sum
● Nak
ID
Data Length Ack/Nak
0x03
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x92
ERR
109
* HDMI Black Level Control
● Function
Personal Computer turns HDMI Black Level function of TV / Monitor.
● Get HDMI Black Level Status
Header
0xAA
Command
0x94
ID
Data Length
0x00
Check
Sum
Data Length
Data 1
● Set HDMI Black Level
Header
0xAA
Command
0x94
ID
0x01
HDMI_b
Check
Sum
HDMI_b : HDMI Black Level Control code set on TV/Monitor
0
1
Normal
Low
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
Data Length Ack/Nak
0x03
'A'
r-CMD
0x94
Val 1
Check
Sum
Val 1
Check
Sum
HDMI_b
● Nak
Header
0xAA
Data Length Ack/Nak
0x03
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x94
ERR
110
* Gamma Control
● Function
The PC adjusts the Gamma Control of a TV or monitor.
● Get Gamma Status
Header
0xAA
Command
0x96
ID
Command
0x96
ID
Data Length
0x00
Check
Sum
Data Length
Data 1
● Set Gamma
Header
0xAA
0x01
GAMMA
Check
Sum
GAMMA : Gamma code to be set on TV/Monitor
0x00
0x01
0x02
0x03
0x04
Natural
Mode1
Mode2
Mode3
Custom
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
Data Length Ack/Nak
0x03
'A'
r-CMD
0x96
Val 1
Check
Sum
Val 1
Check
Sum
GAMMA
● Nak
Header
0xAA
Data Length Ack/Nak
0x03
'N'
ERR : Error code that shows what occurred error is
r-CMD
0x96
ERR
111
* Reset Control
● Function
The PC adjusts the Reset Control of a TV or monitor.
● Get Reset Status
Not Available
Header
Command
0xAA
0x9F
Data Length
ID
0x00
Check
Sum
Data Length
Data 1
● Set Reset
Header
0xAA
Command
0x9F
ID
0x01
RST
Check
Sum
RST : Reset code to be set on TV/Monitor
0x00
0x01
0x02
0x03
Picture Reset
Sound Reset
Setup Reset
Reset All
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
Data Length Ack/Nak
0x03
'A'
r-CMD
0x9F
Val 1
Check
Sum
r-CMD
0x9F
Val 1
Check
Sum
RST
● Nak
Header
0xAA
Data Length Ack/Nak
0x03
'N'
ERR : Error code that shows what occurred error is
ERR
112
* Ambient Brightness Control (460UT(n)- 2)
● Function
The PC adjusts Ambient Brightness Mode On/Off of a TV or monitor.
And, Setting Lamp value for Ambient Brightness On.
● Get Ambient Brightness Mode Status
Header
0xAA
Command
Data Length
ID
0xA1
0x00
Check
Sum
● Set Ambient Brightness Mode, and Set Lamp Value
Header
0xAA
Command
ID
0xA1
Data
Length
Data 1
0x03
AB_Mode
Data 2
Valid_
LampValu
e
ID : The ID value is selected as below.
Target ID
0xFE, 0xFF
Data 3
Lamp
Value
Check
Sum
Set Ambient Brightness Mode On/ Off
Set Lamp Value
AB_Mode: Ambient Mode On/Off code to be set on TV/Monitor
0x00
0x01
Ambient Brightness Mode Off
Ambient Brightness Mode On
Valid_LampValue : Lamp Value Apply/Not apply to be set on TV/Monitor
0x00
0x01
Invalid Lamp Value(Don't apply)
Valid Lamp Value (Apply)
Lamp Value : Lamp Value to be set on TV/Monitor (0 ~ 100),
● Ack : If user command set lamp value, there will be no ack.
Header Command
0xAA
0xFF
ID
Data
Length
Ack/N
ak
rCMD
0x04
'A'
0xA1
Val 1
Val 2
AB_M Lamp
ode Value
Check
Sum
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
0x03
'N'
ERR : Error code that shows what occurred error is
r-CMD
0xA1
Val 1
ERR
Check
Sum
113
* RJ45 setting refresh
● Function
Personal Computer controls Ethernet Converter IC Reset.
● Set RJ45 setting Refresh Status
Header
Command
0xAA
0xA2
ID
Data Length
0x01
Data
Reset
Command
Check
Sum
Reset Command:
Command: Reset Ethernet Converter IC on TV/Monitor
0x01
Reset
● Ack
Header
Comman
d
0xAA
0xFF
Header
0xAA
Command
0xFF
ID
Data
Length
Ack/Nak
0x03
'A'
r-CMD
Data
0xA2
Reset
Comman
d
Check
Sum
● Nak
ERR :
ID
Data Length Ack/Nak
0x03
'N'
r-CMD
0xA2
Val 1
ERR
Check
Sum
Error code that shows what occurred error is
114
* OSD Display Type On/ Off
● Function
The PC adjusts the OSD Display Control of a TV or monitor.
"OSD On" means, It is display that OSD Type.
"OSD Off" means, It is not dispaly that OSD Type.
● Get OSD Enable Status
Header
0xAA
Command
ID
0xA3
Data Length
0x00
Check
Sum
Data Length
Data 1
● Set OSD Enable/Disable
Header
Command
0xAA
0xA3
ID
0x02
OSD
Type
Data 2
OSD
On/Off
Check
Sum
OSD Type:
Type: Select OSD Type code to be set on TV/Monitor
0x00
0x01
0x02
0x03
Source OSD
Not Optimum Mode OSD
No Signal OSD
MDC OSD
OSD ON/OFF:
ON/OFF: Adjust OSD On/Off code to be set on TV/Monitor
0x00
0x01
OSD Off
OSD On
● Ack
Header Comman
d
0xAA
ID
0xFF
BIT4
BIT3
Data
Length
Val 1
BIT2
Ack/Nak r-CMD
0x03
BIT1
'A'
BIT7
0xA3
Val 1
BIT6
Reserved
BIT5
BIT0
Check
Type 0 Sum
Reserv Type 3 Type 2 Type 1
ed On/Off On/Off On/Off On/Off
Type(OSD Type) : Same as Above.
● Nak
Header
0xAA
ERR :
Command
0xFF
ID
Data Length Ack/Nak
0x03
'N'
r-CMD
0xA3
Val 1
ERR
Check
Sum
Error code that shows what occurred error is
115
* Timer1 Control
● Function:
Personal Computer controls the Timer1 that TV / Monitor.
(It is dependent on Product Specifications.)
● Get Timer1 Status
Header
0xAA
Command
ID
0xA4
Data Length
0
Check
Sum
● Set Timer1
Header
Command
0xAA
0xA4
ID
Data 6 Date 7 Data 8
Data
Length
0x0D
Data 9
Data 1
On H
Data
10
Data
11
Data 2
Data 3
Data 4
On On_Act
On M AM/PM
Data 12
Data 13
Off Off_Act Repeat WMeaenkudaal Volume Source Holiday
Off M AM/PM
Apply
y
On H : On Time Hour value to be set on TV/Monitor ( 1 ~ 12 )
On M : On Time Minute value to be set on TV/Monitor ( 0 ~ 59 )
On AM/PM :On Time AM/PM value to be set on TV/Monitor (0~1)
0x00
0x01
On_Act
Data 5
Off H
Check
Sum
PM
AM
: On Time Inactivated /Activated to be set on TV/Monitor (0(off)~1(on))
Off H : Off Time Hour value to be set on TV/Monitor ( 1 ~ 12 )
Off M : Off Time Minute value to be set on TV/Monitor ( 0 ~ 59 )
Off AM/PM : Off Time AM/PM value to be set on TV/Monitor (0~1)
0x00
0x01
Off_Act
Repeat
PM
AM
: Off Time Inactivated /Activated to be set on TV/Monitor (0(off)~1(on))
: Repeat value to be set on TV/Monitor (0~5)
0:Once 1:Everyday 2:Mon~Fri 3:Mon~Sat 4:Sat~Sun 5:Manual Weekday
ManualWeekday : Weekday value to be set on TV/Monitor.
BIT7
BIT6
BIT5
BIT4
BIT3
BIT2
BIT1
BIT0
X
Sat
Fri
Thu
Wed
Tue
Mon
Sun
BIT7 : Don't care
Volume : Volume to be set on TV/Monitor.
Source : Source to be set on TV/Monitor.
Holiday Apply : Holiday Apply/Don't Apply to be set on TV/Monitor. (0~1)
0x00
0x01
Dont't Apply
Apply
116
● Ack
Header Comman
d
0xAA
0xFF
Val 4 Val 5 Val 6
Data
Length
ID
Ack/Nak r-CMD
0x0F
Val 7
'A'
0xA4
Val 8 Val 9 Val 10
Val 1
On H
Val
11
Val
12
Val 2
Val 3
On
On M AM/PM
Val
13
On_A Off H Off M Off Off_Act Repeat WMeaenkudlaa Volume Source Holiday
ct
AM/PM
Apply
y
Check
Sum
Val1 ~ Val13: Same as above
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
0x03
'N'
ERR : Error code that shows what occurred error is
r-CMD
0xA4
Val 1
ERR
Check
Sum
117
* Timer2 Control
● Function:
Personal Computer controls the Timer2 that TV / Monitor.
(It is dependent on Product Specifications.)
● Get Timer2 Status
Header
0xAA
Command
ID
0xA5
Data Length
0
Check
Sum
● Set Timer2
Header
Command
0xAA
0xA5
ID
Data 6 Date 7 Data 8
Data
Length
0x0D
Data 9
Data 1
On H
Data
10
Data
11
Data 2
Data 3
Data 4
On On_Act
On M AM/PM
Data 12
Data 13
Off Off_Act Repeat WMeaenkudaal Volume Source Holiday
Off M AM/PM
Apply
y
On H : On Time Hour value to be set on TV/Monitor ( 1 ~ 12 )
On M : On Time Minute value to be set on TV/Monitor ( 0 ~ 59 )
On AM/PM :On Time AM/PM value to be set on TV/Monitor (0~1)
0x00
0x01
On_Act:
Data 5
Off H
Check
Sum
PM
AM
On Time Inactivated /Activated to be set on TV/Monitor (0(off)~1(on))
Off H : Off Time Hour value to be set on TV/Monitor ( 1 ~ 12 )
Off M : Off Time Minute value to be set on TV/Monitor ( 0 ~ 59 )
Off AM/PM : Off Time AM/PM value to be set on TV/Monitor (0~1)
0x00
0x01
PM
AM
Off_Act : Off Time Inactivated /Activated to be set on TV/Monitor (0(off)~1(on))
Repeat
: Repeat value to be set on TV/Monitor (0~5)
0:Once 1:Everyday 2:Mon~Fri 3:Mon~Sat 4:Sat~Sun 5:Manual Weekday
ManualWeekday : Weekday value to be set on TV/Monitor.
BIT7
BIT6
BIT5
BIT4
BIT3
BIT2
BIT1
BIT0
X
Sat
Fri
Thu
Wed
Tue
Mon
Sun
BIT7 : Don't care
Volume : Volume to be set on TV/Monitor.
Source : Source to be set on TV/Monitor.
Holiday Apply : Holiday Apply/Don't Apply to be set on TV/Monitor. (0~1)
0x00
0x01
Dont't Apply
Apply
118
● Ack
Header Comman
d
0xAA
0xFF
Val 4 Val 5 Val 6
Data
Length
ID
Ack/Nak r-CMD
0x0F
Val 7
'A'
0xA5
Val 8 Val 9 Val 10
Val 1
On H
Val
11
Val
12
Val 2
Val 3
On
On M AM/PM
Val
13
On_A Off H Off M Off Off_Act Repeat WMeaenkudlaa Volume Source Holiday
ct
AM/PM
Apply
y
Check
Sum
Val1 ~ Val13: Same as above
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
0x03
'N'
ERR : Error code that shows what occurred error is
r-CMD
0xA5
Val 1
ERR
Check
Sum
119
* Timer3 Control
● Function:
Personal Computer controls the Timer3 that TV / Monitor.
(It is dependent on Product Specifications.)
● Get Timer3 Status
Header
0xAA
Command
ID
0xA6
Data Length
0
Check
Sum
● Set Timer3
Header
Command
0xAA
0xA6
ID
Data 6 Date 7 Data 8
Data
Length
0x0D
Data 9
Data 1
On H
Data
10
Data
11
Data 2
Data 3
Data 4
On On_Act
On M AM/PM
Data 12
Data 13
Off Off_Act Repeat WMeaenkudaal Volume Source Holiday
Off M AM/PM
Apply
y
On H : On Time Hour value to be set on TV/Monitor ( 1 ~ 12 )
On M : On Time Minute value to be set on TV/Monitor ( 0 ~ 59 )
On AM/PM :On Time AM/PM value to be set on TV/Monitor (0~1)
0x00
0x01
On_Act
Data 5
Off H
Check
Sum
PM
AM
: On Time Inactivated /Activated to be set on TV/Monitor (0(off)~1(on))
Off H : Off Time Hour value to be set on TV/Monitor ( 1 ~ 12 )
Off M : Off Time Minute value to be set on TV/Monitor ( 0 ~ 59 )
Off AM/PM : Off Time AM/PM value to be set on TV/Monitor (0~1)
0x00
0x01
PM
AM
Off_Act : Off Time Inactivated /Activated
to be set on TV/Monitor (0(off)~1(on))
Repeat : Repeat value to be set on TV/Monitor (0~5)
0:Once 1:Everyday 2:Mon~Fri 3:Mon~Sat 4:Sat~Sun 5:Manual Weekday
ManualWeekday : Weekday value to be set on TV/Monitor.
BIT7
BIT6
BIT5
BIT4
BIT3
BIT2
BIT1
BIT0
X
Sat
Fri
Thu
Wed
Tue
Mon
Sun
BIT7 : Don't care
Volume : Volume to be set on TV/Monitor.
Source : Source to be set on TV/Monitor.
Holiday Apply : Holiday Apply/Don't Apply to be set on TV/Monitor. (0~1)
0x00
0x01
Don't Apply
Apply
120
● Ack
Header Comman
d
0xAA
0xFF
Val 4 Val 5 Val 6
Data
Length
ID
Ack/Nak r-CMD
0x0F
Val 7
'A'
0xA6
Val 8 Val 9 Val 10
Val 1
On H
Val
11
Val
12
Val 2
Val 3
On
On M AM/PM
Val
13
On_A Off H Off M Off Off_Act Repeat WMeaenkudlaa Volume Source Holiday
ct
AM/PM
Apply
y
Check
Sum
Val1 ~ Val13: Same as above
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
0x03
'N'
ERR : Error code that shows what occurred error is
r-CMD
0xA6
Val 1
ERR
Check
Sum
121
* Clock Control
● Function
Personal Computer controls current time of TV / Monitor.
(It is dependent on Product Specifications.)
● Get Clock Status
Header
0xAA
Command
0xA7
ID
Data Length
0x00
Check
Sum
Data Length
Data 1
● Set Clock
Header
0xAA
Command
Data 5
Data 6
Year1
0xA7
Year2
ID
Data 7
AmPm
0x07
Day
Data 2
Hour
Data 3
Data 4
Val 1
Val 2
Val 1
Check
Sum
Minute
Month
Check
Sum
Day : Day value to be set on TV/Monitor ( 1 ~ 31 )
Month : Month value to be set on TV/Monitor ( 1 ~ 12 )
Year1 : Year value to be set on TV/Monitor (High Byte)
Year2 : Year value to be set on TV/Monitor (Low Byte)
ex) Current year is 2010.
2010(Dec) → 0x07DA(Hex)
Year1: 0x07
Year2: 0xDA
Hour : Hour value to be set on TV/Monitor ( 1 ~ 12 )
Minute : Minute value to be set on TV/Monitor ( 0 ~ 59 )
AmPm : AM/PM value to be set on TV/Monitor (0 ~ 1)
0x00
0x01
PM
AM
● Ack
Header
0xAA
Command
0xFF
ID
Val 3
Val 4
Val 5
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
0x09
'A'
Val 6
Val 7
r-CMD
0xA7
Day
Hour
Check
Sum
Year1
Year2
AmPm
Minute Month
Hour, Minute : Same as above
Note : Hour,
our, Minute if current time was not set on Monitor, 0xFF
● Nak
Data Length Ack/Nak
0x03
'N'
ERR : Error code that shows what occurred error is
r-CMD
0xA7
ERR
122
* Holiday Add/ Delete Control
● Function
Personal Computer controls Holiday List of TV / Monitor.
(It is dependent on Product Specifications.)
● Set Holiday Status
Header
Command
0xAA
0xA8
Data 5
Check
Sum
Day_E
Data
Length
ID
0x05
Management Command:
Command: Adjust Command
0x00
0x01
0x02
Data 1
Data 2
Manageme
nt
Month_S
command
Data 3
Data 4
Day_S
Month_E
Holiday List of TV / Monitor.
Add Holiday
Delete Holiday
Delete All
Add Holiday : Add New Holiday Information "Month_S/Day_S ~ Month_E/Day_E".
Delete Holiday : Delete one Holiday Information "Month_S/Day_S ~ Month_E/Day_E".
Delete All : Delete All Holiday Information.("Data2 ~ Data5" must be 0x00.)
● Ack
Data Length Ack/Nak
Header
Command
0xAA
0xFF
Val 3
Val 4
Val 5
Header
0xAA
Command
0xFF
ID
Day_S Month_E
ID
Day_E
0x07
'A'
r-CMD
0xA8
Val 1
Val 2
Val 1
Check
Sum
Managem
ent Month_S
command
Check
Sum
● Nak
Data Length Ack/Nak
0x03
'N'
ERR : Error code that shows what occurred error is
r-CMD
0xA8
ERR
123
* Holiday Get Control
● Function
Personal Computer get Holiday List of TV / Monitor.
(It is dependent on Product Specifications.)
● Get Total Number of Holiday
Request Total number of Holiday information of TV/Monitor.
Header
0xAA
Command
0xA9
ID
Data Length
0x00
Check
Sum
Data Length
Data 1
● Get Holiday Date
Header
0xAA
Index :
Command
0xA9
ID
0x01
Index
Check
Sum
Index value on Holiday List.
● Ack
Header
0xAA
Command
0xFF
ID
Val 3
Val 4
Val 5
Day_S Month_E
Day_E
Data Length Ack/Nak
0x07
'A'
r-CMD
0xA9
Val 1
Index
Index
Month_S
Check
Sum
Rule of Ack Command.
Command Index(Ac
Month_S(Ack) Day_S(Ack) Month_E(Ack)
Type
k)
Get Number
Total
0x00
0x00
0x00
of Holiday
number
Get Holiday
Date
Month_S
Day_S
Month_E
(If there is
Index
(Index's data) (Index's data) (Index's data)
holiday
information)
Get Holiday
Date
(If there is
no holiday
information)
Val 2
0xFF
0xFF
0xFF
Day_E(Ack)
0x00
Day_E
(Index's
data)
0xFF
● Nak
Header
0xAA
Command
0xFF
ID
Data Length Ack/Nak
0x03
'N'
ERR : Error code that shows what occurred error is
r-CMD
0xA9
Val 1
ERR
Check
Sum
124
* Panel On/Off
● Function
Personal Computer turns Panel of TV / Monitor on/off.
When input signal is changed, Panel turns on, (PN_State turns to PANEL ON, too.)
● Get Panel ON/OFF Status
Header
0xAA
Command
0xF9
Data Length
ID
0
Check
Sum
Data Length
Data 1
● Set Dynamic Contrast ON/OFF
Header
0xAA
Command
0xF9
ID
1
PN_State
Check
Sum
PN_State : Panel ON/OFF code to be set on TV/Monitor
1
0
PANEL OFF
PANEL ON
● Ack
Header
0xAA
Command
0xFF
ID
Command
0xFF
ID
Data Length Ack/Nak
3
'A'
r-CMD
0xF9
Val 1
Check
Sum
Val 1
Check
Sum
PN_State
● Nak
Header
0xAA
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0xF9
ERR
125
* Auto ID Setting MDC Control Command
● Function
● Get Auto ID
Header Command
0xAA
0xFD
● Set Auto ID
Header Command
0xAA
0xFD
Data Length
ID
ID
0
Data Length
2
Data 1
RS_Status
Check
Sum
Data 2
CheckSum
M_ID
* If the value of M_ID is 0, ID is not changed. (Maintain previous value.)
RS_Status : RS232 Output & ID initialization information.
Bit7 Bit6 Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
0
0
0
1 or 0
0
0
0
1 or 0
1 : Initialize Monitor ID
1 : RS232 Loop Out Disable
0 : Set Monitor ID
0 : RS232 Loop Out Enable
* Initialization information of Monitor ID at Ack of Get Auto ID is unknown.
M_ID : Change ID
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
Change ID(1~99)
* If RS_Status Monitor ID's reset bit sets 1, M_ID value will be ignored.
● Ack
Header Command
0xAA
0xFF
Data
Length Ack/Nak r-CMD
ID
4
'A'
0xFD
Val 1
Val 2
RS_Status M_ID
Check
Sum
* M_ID is a current set ID.
● Nak
Header Command
0xAA
0xFF
ID
Data Length Ack/Nak
3
'N'
ERR : Error code that shows what occurred error is
r-CMD
0xFD
Val 1
ERR
Check
Sum
126
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement