SureCross™ DX70 單點對單點模組

SureCross™
DX70 單點對單點模組
§ DX70無線傳輸模組提供使用者經濟簡便的解決方案。
§ DX70無線傳輸模組,在同一頻道上為同一台通到模
組與一台節點模組雙向傳輸。
§ 利用跳頻技術(FHSS)分時多工(TDMI)可穩定使用於
工業環境來傳輸I/O資料。
§ DX70模組支援數位訊號、類比訊號雙向傳輸。
§ 擁有堅固且達IP67防水等。
DX70, 10-30V dc
頻率
I/O
通道模組型號
節點模組型號
2.4GHz
Discrete:
Four selectable inputs, four PNP outputs
DX70G2X6S4P4M2M2
Analog:
Two selectable inputs, two 0-20 mA outputs
DX70N2X6S4P4M2M2
2.4GHz
Gateway Discrete:
Four selectable inputs,eight PNP outputs
Node Discrete:
Eight selectable inputs,four PNP outputs
DX70N2X6S8P4
www.e-sensors.com.tw
DX70G2X6S4P8
BX 1-1
SureCross™ DX70 單點對單點模組
專用連接線
支架
Flex Power 附件
Flex Power 專用感測器
Flex Power K50 指示燈
保護外箱
直流電源供應器,24V dc
繼電器盒
www.e-sensors.com.tw
BX 1-2
SureCross™ DX70 單點對單點模組
天線專用連接線
天線
天線專用連接線
突波吸收器
www.e-sensors.com.tw
BX 1-3
SureCross™ DX70 Wireless Products
Configured Discrete and Analog I/O
Features
The SureCross™ DX70 wireless series consists of a radio frequency network system built
around two devices and configured I/O.
2.4 GHz
900 MHz
• Wireless industrial I/O system with discrete (sourcing or sinking) inputs and outputs,
analog inputs and outputs, and link loss output*
• +10 to 30V dc power input
• Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple
Access (TDMA) control architecture combine to ensure reliable data delivery within the
unlicensed Industrial, Scientific, and Medical (ISM) bands
• Transceivers for two-way communication between the devices, including fully
acknowledged data transmission
• Lost RF links are detected and relevant outputs go to user-defined default states
• External or internal antenna
• 900 MHz or 2.4 GHz frequencies
• Built-in signal strength indication
For additional information and a complete list of accessories, including FCC approved
antennas, please refer to Banner Engineering’s website, www.bannerengineering.com/
surecross.
* Link loss output may be selected or deselected to be one of the four outputs
Contents
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Device Components . . . . . . . . . . . . . . . . . . . . 3
DX70 Dimensions. . . . . . . . . . . . . . . . . . . . . . 4
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . 11
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . 12
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . 13
FCC Certification 900 MHz. . . . . . . . . . . . . . 15
FCC Certification, 2.4 GHz. . . . . . . . . . . . . . 16
Certified Countries List . . . . . . . . . . . . . . . . . 17
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 19
WARNING . . . Not To Be Used for Personnel Protection
Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death.
These devices do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications.
A device failure or malfunction can cause either an energized or de-energized output condition. Consult your current Banner Safety
Products catalog for safety products that meet OSHA, ANSI, and IEC standards for personnel protection.
Printed in USA
01/2010 P/N 133214 rev. G
SureCross™ DX70 Wireless Systems
Models
Device
Nodes
Models
DX70N9X6S4P4M2M2
Frequency
Power
900 MHz ISM Band
DX70N9X6W4P4M2M2
DX70N2X6S4P4M2M2
DX70G9X6S4P4M2M2
2.4 GHz ISM Band
900 MHz ISM Band
External
+10 to 30V dc
DX70G9X6W4P4M2M2
DX70G2X6S4P4M2M2
DX70N9X6S8P4
2.4 GHz ISM Band
Internal
900 MHz ISM Band
External
Internal
2.4 GHz ISM Band
DX70N2X6W8P4
Gateway
DX70G9X6S4P8
900 MHz ISM Band
DX70G9X6W4P8
DX70G2X6S4P8
DX70G2X6W4P8
External
Discrete Inputs: Four Selectable
Discrete Outputs: Four Sourcing
Analog Inputs: Two 0-20 mA
Analog Outputs: Two 0-20 mA
External
DX70N9X6W8P4
DX70N2X6S8P4
Internal
Internal
DX70G2X6W4P4M2M2
Node
I/O
Internal
DX70N2X6W4P4M2M2
Gateways
Antenna
External
External
+10 to 30V dc
Internal
External
Internal
2.4 GHz ISM Band
Discrete Inputs: Eight Selectable
Discrete Outputs: Four Sourcing
External
Discrete Inputs: Four Selectable
Discrete Outputs: Eight Sourcing
Internal
DX70 devices should only be paired in the similar I/O structure groupings listed. The P4M2M2 devices are paired together, as are the 8P4 and
4P8 devices. Do not mix and match between groups.
2 P/N 133214 rev. G
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX70 Wireless Systems
Device Components
1
1
2
Rotary Dials. After the DX70 devices are bound, use the rotary
dials on the Gateway to set the Network ID (NID) to a decimal
value from 1 to 32.
LEDs. Power LED - Power indicator. A green LED indicates
the power is on. Signal LED - Provides real-time feedback
regarding RF link status and communications activity.
2
3
4
5
6
Port, NPT Gland, or Plug. If unused, install the provided plug into the 1/2
NPT threaded port. Use PTFE tape if an IP67 seal is required.
Housing. The rugged, industrial DX70 housing meets IEC IP67 standards.
Mounting Hole, #10/M5 Clearance. Mounting holes accept metric M5 or
UNC/UNF #10 hardware — DIN rail mount adapter bracket available
Wiring Terminal Strip. The 16 wiring terminals accept wire sizes: AWG 12-28
or 2.5 mm²
3
4
5
6
3
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
P/N 133214 rev. G 3
SureCross™ DX70 Wireless Systems
DX70 Dimensions
65.0
[2.56”]
7.9
[0.31”]
65.0
[2.56”]
80.3
[3.16”]
7.65
[0.30”]
106
[4.17”]
1/2” NPT
60
[2.36”]
14.67
[0.578”]
80.8
[3.18”]
4 P/N 133214 rev. G
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX70 Wireless Systems
Installation
Step 1: Apply Power
Connect power to the DX70 Gateway and
Node by connecting your power directly
to the terminal block PWR. Connect your
ground to the GND terminal block.
Power Connection
Terminal Block
PWR
GND
Function
+10 to 30V dc input
dc common
power
ground
PWR PWR
GND GND
AO2 AI2
AO1 AI1
D04 DI4
DO3 DI3
DO2 DI2
DO1 DI1
P2
G B - W +
Step 2: Bind the Devices
Binding two DX70 devices locks the Node to a specific Gateway by teaching the Node the Gateway’s unique serial number. After the two
devices are bound, the Node only accepts data from the Gateway it is bound to. New or replacement devices from the factory require binding
before operation.
If the power is applied and the Power LED is solid green and the Signal LED is solid red for more than thirty seconds (indicating an RF link
error), the devices need to be bound. To bind follow these steps:
1. Install the supplied antennas to both the Gateway and Node.
2. Apply power to both devices and position the Gateway and Node about two meters apart.
The Power LED is solid green and the Signal LED is solid red, indicating an RF link error.*
3. Remove the rotary dial access covers.
4. On the Gateway, set the rotary dials to 00, then set the rotary dials to FF.
The Gateway enters binding mode. Note that the rotary dials for each device must be changed to FF after applying power, not before
applying power. Both the POWER and SIGNAL LEDs flash red.
5. On the Node, set the rotary dials to 00, then set them to FF.
The Node enters binding mode and waits for the Gateway to respond. Both the Gateway’s and Node’s LEDs alternately flash red
during pairing.
After the devices are successfully bound, the Node’s LEDs are solid red for a few seconds and the Node automatically exits binding
mode. The Node Power LED is solid green and Signal LED is solid red, indicating the Node is bound. Binding should take less than
twenty seconds.
6. Change the Gateway’s rotary dials to a valid Network ID.
Valid Network IDs are 01 through 32, in decimal, established using both rotary dials. The left dial may be set to 0, 1, 2, or 3. The right
dial may be set from 0 to 9 when the left dial is at 0, 1, or 2; or set to 0 through 2 when the left dial is at 3. (Positions A through F are
invalid network ID numbers.) In the example shown to the right, the Network ID is set to 10.**
7. The Node automatically synchronizes to the Gateway and establishes a radio link in less than a minute.
When a radio link is established, the Power LED is green and the Signal LED flashes yellow on both
devices to indicate the signal strength.
8. On the Node, set the rotary dials back to 00, or any position other than FF.
9. Replace both the rotary dial access covers.
Regardless of the position of the Node’s rotary dials, the DX70 devices within this bound pair maintain a radio link. For successful binding, the
Gateway and Node should be at least two meters apart and have the antennas installed.
* Unbound devices will have a solid green Power LED and solid red Signal LED thirty seconds after power up. Bound devices have a solid green Power LED and a flashing
yellow Signal LED within thirty seconds of power up.
** When multiple networks operate in the same area, assign a unique Network ID (NID) to the Gateway device within each bound pair. For more information about collocated
networks and Network IDs, refer to the Troubleshooting section.
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
P/N 133214 rev. G 5
SureCross™ DX70 Wireless Systems
Step 3: Verify Communications
After applying power to the devices, the Power LED is solid green. Until communication is established, the Signal LEDs are solid red. When
communication is established, the Signal LED flashes yellow; the frequency of the flash indicates the communication signal strength.
If testing the devices before installation, verify the devices are at least two meters apart to avoid over-driving the link.
Status
Power LED
Signal LED
Power Applied
Green Solid
—
RF Link Error
Green Solid
Red Solid
RF Link Good
Green Solid
Yellow Flash
Binding Mode
Red Flash
Red Flash
Successful Binding (Node)
Red Solid (for 3 sec.)
Red Solid (for 3 sec.)
Communication Signal Strength
The rate at which the Signal LED blinks yellow indicates the signal strength between the Gateway and Node.
Blink Rate
Definition
Every 1/8 second
Less than 3% missed packets
Every 1/4 second
Between 3% and 25% missed packets
Every 1/2 second
Between 26% and 50% missed packets
Every 1 second
More than 50% missed packets
Step 4: Sensor Connections
Configured Input/Output Mapping, 4P4M2M2 Models
Terminal Block
Label
DX70
DX70
Gateway
Node
DI1
Discrete IN 1*
Discrete OUT 1 or Lost Link*
DO1
AO2 AI2
DI2
Discrete IN 2
Discrete OUT 2
DO2
AO1 AI1
DI3
Discrete IN 3
Discrete OUT 3
DO3
D04 DI4
PWR PWR
GND GND
DI4
Discrete IN 4
Discrete OUT 4
DO4
DO2 DI2
AI1
Analog IN 1
Analog OUT 1
AO1
DO1 DI1
AI2
Analog IN 2
Analog OUT 2
AO2
DO1
Discrete OUT 1 or Lost Link*
Discrete IN 1*
DI1
DO2
Discrete OUT 2
Discrete IN 2
DI2
DO3
Discrete OUT 3
Discrete IN 3
DI3
DO4
Discrete OUT 4
Discrete IN 4
DI4
AO1
Analog OUT 1
Analog IN 1
AI1
AO2
Analog OUT 2
Analog IN 2
AI2
DO3 DI3
P2
Terminal Block
Label
G B - W +
* If digital output 1 is used as a lost link output (default) then digital input 1 is non-functional. Please refer to the Configuration section to change this setting. Input 1 is not
available when the lost link output is selected.
6 P/N 133214 rev. G
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX70 Wireless Systems
Discrete Input Wiring (Sourcing)
Discrete Input Wiring (Sinking)
Discrete Output Wiring (Sourcing)
DIx
DIx
DOx
PWR or SPx
GND
GND
Analog Input Wiring
Analog Output Wiring
+10 to 30V dc
AIx
AOx
PWR or SPx
Refer to the sensing device data sheet for a
device specific wiring diagram.
GND
Do not exceed analog input ratings for analog
inputs. Only connect sensor outputs to analog inputs.
Configured Input/Output Mapping, 8P4 to 4P8 Models
DO8 PWR
P2
Terminal Block
Label
PWR DI8
DO7 GND
GND DI7
DO6 PWR
PWR DI6
DO5 GND
GND DI5
D04 DI4
D04 DI4
DO3 DI3
DO3 DI3
DO2 DI2
DO2 DI2
DO1 DI1
DO1 DI1
G B - W +
DX70
P2
G B - W +
DX70
Terminal Block
Label
Gateway
Node
DI1
Discrete IN 1
Discrete OUT 1
DO1
DI2
Discrete IN 2
Discrete OUT 2
DO2
DI3
Discrete IN 3
Discrete OUT 3
DO3
DI4
Discrete IN 4
Discrete OUT 4
DO4
DO1
Discrete OUT 1
Discrete IN 1
DI1
DO2
Discrete OUT 2
Discrete IN 2
DI2
DO3
Discrete OUT 3
Discrete IN 3
DI3
DO4
Discrete OUT 4
Discrete IN 4
DI4
DO5
Discrete OUT 5
Discrete IN 5
DI5
DO6
Discrete OUT 6
Discrete IN 6
DI6
DO7
Discrete OUT 7
Discrete IN 7
DI7
DO8
Discrete OUT 8
Discrete IN 8
DI8
The lost link option is not available on this model.
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
P/N 133214 rev. G 7
SureCross™ DX70 Wireless Systems
Step 5: Configure the Devices
Switches
Use the switches on the circuit board to set:
•
•
•
•
link output error response
input type
output or link mapping
link timout
Changes made to the DIP switches affect all I/O for this device.
Device Settings
1
2
Link Loss Outputs: Off / 0 mA
OFF*
OFF*
Link Loss Output: On / 20 mA
ON
OFF
Link Loss Output: Hold Last State / Value
OFF
ON
Reserved
ON
ON
Switches
3
Discrete Input: PNP
OFF*
Discrete Input: NPN
ON
Map Output 1 to Link Error
Map Output 1 to Input 1
4
5
OFF*
ON
Link Timeout: 4 seconds
OFF*
Link Timeout: 1 second
ON
* Default positions. Input 1 is not available when the lost link output is selected.
** The lost link option is only available on the 4P4M2M2 models.
Accessing the DIP Switches
Discrete Input Type
To access the DIP switches, follow these steps:
Unscrew the four screws that mount the cover to the bottom housing.
1. Remove the cover from the housing without damaging the
ribbon cable or the pins the cable plugs into.
2. Gently unplug the ribbon cable from the board mounted into
the bottom housing.
3. Remove the black cover plate from the bottom of the
device’s cover.
The DIP switches are located behind the rotary dials. After making the
necessary changes to the DIP switches, place the black cover plate
back into position and gently push into place. Plug the ribbon cable
in after verifying that the blocked hole lines up with the missing pin.
Mount the cover back onto the housing.
Select the discrete input type: sourcing (PNP) or sinking (NPN).
8 P/N 133214 rev. G
Link Loss Outputs
The SureCross™ DX80 wireless devices use a deterministic link timeout method to address RF link interruption or failure. When a radio
link fails, all pertinent wired outputs are sent to defined states until the
link is recovered, ensuring that disruptions in the communications link
result in predictable system behavior.
Following a time-out, all outputs linked to the Node in question are set
to de-energize (discrete outputs to zero, analog outputs to 0 mA or 4
mA), energize (discrete outputs to one, analog outputs to 20 mA), or
to hold the last stable state/value. Use the DIP switches to select the
link loss output state.
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX70 Wireless Systems
Step 6: Installation
Avoid Direct Sunlight
To minimize the damaging effects of ultra-violet radiation, avoid mounting
the devices facing intense direct sunlight.
•
•
•
•
Mount the DX70 within a protective enclosure,
Mount the DX70 under an overhang or other source of shade,
Install the DX70 indoors, or
Face the units north when installing outside.
Avoid Collecting Rain
When possible, mount the DX70 where rain or snow will drain away from
the unit.
• Mount the units vertically so that precipitation, dust, and dirt do not
accumulate on permeable surfaces.
• Avoid mounting the units on flat or concave surfaces, especially if the
display will be pointing up.
Reduce Chemical Exposure
Before installing the DX70 units in a chemically harsh environment,
contact Banner for more information regarding the life-expectancy.
Solvents, oxidizing agents, and other chemicals can damage the DX70.
Minimize Mechanical Stress
Avoid Direct Sunlight
While the DX70 is very durable, it is a sophisticated electronic device that
is sensitive to shock and excessive loading.
• Avoid mounting the units to an object that may be shifting or vibrating
excessively. High levels of static force or acceleration may damage
the housing or electronic components.
• Do not subject the DX70 to external loads. Do not step on the DX70
or use it as a handgrip.
• Do not allow long lengths of cable to hang from the DX70 glands.
Cabling heavier than 100 grams should be supported instead of
allowed to hang from the DX70 housing.
Weather-Proofing Plugs
If the DX70 is mounted outdoors or will be exposed to moisture, dirt, or dust, follow these steps to weatherproof the units.
Watertight 1/2” NPT Plug
Seal the 1/2” NPT port if it is not used. To install a watertight NPT plug:
1. Wrap 12 to 16 passes of PTFE tape evenly across the length of the threads.
2. Manually thread the plug into the housing port until reaching some resistance.
3. Using a 9/16” crescent wrench, turn the plug until all the plug’s threads are engaged by the housing port.
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
P/N 133214 rev. G 9
SureCross™ DX70 Wireless Systems
Antenna Installation
When installing a remote antenna system, always include a lightning arrestor/coaxial surge protector in the system. Remote antenna systems
installed without a lightning arrestor invalidate the Banner warranty of the SureCross™ family of devices. A remote antenna system is any
antenna system where the antenna is not connected directly to the radio and typically use coaxial cable to connect the antenna to the radio.
Lightning arrestors should be properly grounded and mounted at ground level near where the cabling enters a building. Install the lightning
arrestor indoors or inside a weatherproof enclosure to minimize corrosion or component deterioration. For best results, mount the lightning
arrestor as close to the ground as possible to minimize the length of the ground connection.
No surge protector can absorb all lightning strikes. Do not touch the SureCross devices or any equipment connected to the SureCross devices
during a thunderstorm.
Installation Quick Tips
Clear Communication Paths
A wireless network can be hindered by radio
interference and obstructions in the path
between a receiver and transmitter.
A clear path increases separation range and improves
performance
To achieve the best radio performance,
carefully consider the installation locations for
each of the devices.
Node
Gateway
Increase Height of DX70 Units
Orient the external antenna vertically for
optimal RF communication. If necessary,
consider increasing the height of the DX70
position to improve reception.
Position the DX70 devices higher for better performance
Gateway
10 P/N 133214 rev. G
Node
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX70 Wireless Systems
Maintenance
Main Body Gasket
Check the main body gasket any time the DX70 is opened. Replace
the gasket when it is damaged, discolored, or showing signs of wear.
The gasket must be:
• Fully seated within its channel along the full length of the
perimeter, and
• Positioned straight within the channel with no twisting, stress, or
stretching.
Rotary Dial Access Cover O-Ring
Check the rotary dial access cover o-ring when the access cover
is removed. Replace the o-ring when it is damaged, discolored, or
showing signs of wear. The o-ring should be:
• Seated firmly against the threads without stretching to fit or
without bulging loosely, and
• Pushed against the flanged cover.
When removing or closing the rotary dial access cover, manually twist
the cover into position. Do not allow cross-threading between the
cover and the DX70 face.
Main Body Gasket
Once the cover is in place and manually tightened, use a small
screwdriver (no longer than five inches total length) as a lever to
apply enough torque to bring the cover even with the DX70 cover
surface.
Replacing O-Rings
Please refer to the list of replacement parts included within this guide
and contact Banner Engineering with any questions.
Rotary Dial Access O-Ring
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
P/N 133214 rev. G 11
SureCross™ DX70 Wireless Systems
Troubleshooting
RF Link Time-Out and Recovery
The SureCross™ DX70 wireless devices employ a deterministic link time-out method to address RF link interruption or failure. As soon as
a specific RF link fails, all pertinent wired outputs are brought to a predefined state until the link is recovered (default DIP switch setting).
Through this process, users of Banner wireless networks can be assured that disruptions in the communications link result in predictable
system behavior.
The link time-out feature uses a fully-acknowledged polling method to determine the RF link status of each device on the network. If after a
specified number of sequential polling cycles a device does not acknowledge a message, the devices consider the link to be timed out. Once
a link has timed out, the units must send and receive a specified number of good RF communications packets before the link is reinstated.
Outputs are restored to current values when the link is recovered.
The lost link option is only available on the 4P4M2M2 models.
Link Status
X
1
0
0
Lost Link
OUT 2
OUT N
The RF link between the devices has timed
out. In this example, the lost link is energized
and the outputs have been programmed by
the DIP switches to go to their de-energized
states (default DIP switch position).
Lost Link
OUT 2
0
OUT N
0
1
Link Status
OK
Normal
Lost Link
OUT 2
Normal
OUT N
De-energized
The RF link between the devices has
recovered and the outputs return to their
current states.
Lost Link
OUT 2
OUT N
De-energized
Normal
Normal
A wireless network can be hindered by radio interference and by obstructions in the path of the receiver and transmitter. To achieve the best
radio performance possible, carefully consider the installation locations for all devices. The need for a clear path increases as the transmission
distance increases.
Problem Description
Possible Solutions
Basic power–up issues
No LEDs
Recheck the power connections and power requirements. DX70 devices require 10 to 30V dc.
DX70 devices will not synchronize
Signal LED is solid red or
flashing red for more than
30 seconds
12 P/N 133214 rev. G
If the devices are less than two meters apart, they may not communicate properly (radios may saturate).
The devices may be too far apart to achieve sync – consult factory for options.
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX70 Wireless Systems
Collocated Networks
To prevent interference between collocated wireless networks, assign each wireless network a different Network ID. The Network ID is a unique
identifier assigned to each wireless network using the rotary dials on the Gateway.
Network ID
The Network ID is a unique identifier assigned to each wireless network that minimizes the chances of two collocated networks interfering with
each other. Assigning different NIDs to different networks improves collocation performance in dense installations.
For instructions on how to assign a Network ID to your wireless network refer to the SureCross Wireless I/O Network Manual.
Setting the Network ID on the DX70s
The Network ID is a unique identifier assigned to each wireless network that minimizes the chances of two collocated networks interfering with
each other. Assigning different NIDs to different networks improves collocation performance in dense installations.
To assign the Network ID for the DX70 network, use the Gateway’s rotary dials. Valid Network IDs are 01 through 32, in decimal, establish
using both rotary dials on the Gateway.
1. Set the Gateway’s left dial to either 0, 1, 2, or 3.
2. Set the Gateway’s right dial to any number from 0 to 9 when the left dial is at 0, 1, or 2; or set to 0 through 2 when the left dial is at
3. (Positions A through F are invalid network ID numbers.)
Accessories
Antennas
Model Number
Description
BWA-9Y6-A
Antenna, Yagi, 890-960 MHz, 6.5 dBd, N Female
BWA-9Y10-A
Antenna, Yagi, 890-960 MHz, 10 dBd, N Female
BWA-9O2-C
Antenna, Omni, 902-928 MHz, 2 dBi, Rubber Swivel, RSMA Male
BWA-9O6-A
Antenna, Omni, 902-928 MHz, 6 dBd, Fiberglass, N Female
BWA-9O5-B
Antenna, Omni, 902-928 MHz, 5 dBd/7.2 dBi, With ground plane, N Female
BWA-2O2-C
Antenna, Omni, 2.4 GHz, 2 dBi, Rubber Swivel, RSMA Male
BWA-2O5-C
Antenna, Omni, 2.4 GHz, 5 dBi, Rubber Swivel, RSMA Male
BWA-2O7-C
Antenna, Omni, 2.4 GHz, 7 dBi, Rubber Swivel, RSMA Male
For more information on antenna specifications and the options available for your system, please contact the applications
engineers at Banner Engineering Corp. For general information regarding antennas, please refer to Antenna Basics, Banner
document p/n 132113.
Hardware
Power
BWA-HW-001
Mounting Hardware
SMBDX80DIN
DIN Rail Adapter
BWA-HW-003
Tape, PTFE Sealant
BWA-HW-004
Replacement Seal Pack (O-Ring, Gasket, Rotary Cover)
BWA-CG.5-10
Cable Glands, 1/2-inch NPT, Cordgrips for cable diameters 0.17 to 0.45 inches, 10 pieces
BWA-HP.5-10
Dummy Hole Plugs, 1/2-inch NPT, 10 pieces
BWA-QD5.5
Prewired 5-pin Euro Connector for 1/2-inch NPT Hub entrance
BWA-QD8.5
Prewired 8-pin Euro Connector for 1/2-inch NPT Hub entrance
BWA-QD12.5
Prewired 12-pin Euro Connector for 1/2-inch NPT Hub entrance
SPS101Q
DC Power Supply, 120 mA, 12-30V dc, 5-pin Euro
SPS101QP
DC Power Supply, 120 mA, 12-30V dc, 5-pin Euro, pigtail
PS24W
DC Power Supply, 500 mA, 24V dc
EZAC-E-QE5
DC Power Supply, 700 mA, 24V dc, 5-pin M12 Euro QD, Hardwired AC Power Conn.
EZAC-E-QE5-QS5
DC Power Supply, 700 mA, 24V dc, 5-pin M12 Euro QD, 5-pin Mini QD AC Power Conn.
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
P/N 133214 rev. G 13
SureCross™ DX70 Wireless Systems
Surge Suppressors
Cabling
Cabling, Antenna
Model Number
Description
BWC-LFNMN
Surge Suppressor, 900 MHz/2.4 GHz
BWC-LFNBMN
Surge Suppressor, Bulkhead, 900 MHz/2.4 GHz
BWC-LMRSFRPB
Surge Suppressor, Bulkhead, (RPSM Type), 900 MHz/2.4 GHz
BWA-RIBBON-001
Ribbon Cable, 20-pin DBL socket
MQDC1-506
Cordset, Quick Disconnect, 5-pin Euro, Straight, 2 m
MQDC-806
Cordset, Quick Disconnect, 8-pin Euro with Shield, Straight, 2 m
MQDC-1210
Cordset, Quick Disconnect, 12-pin Euro, Straight, 3 m
BWC-1MRSMN05
LMR200, RSMA to N Male, 0.5 m
BWC-1MRSMN2
LMR200, RSMA to N Male, 2 m
BWC-1MRSFRSB4
RG58, RSMA to RSMAF Bulkhead, 4 m
BWC-1MRSFRSB1
RG58, RSMA to RSMAF Bulkhead, 1 m
BWC-1MRSFRSB2
RG58, RSMA to RSMAF Bulkhead, 2 m
BWC-1MRSFRSB0.2
RG58, RSMA to RSMAF Bulkhead, 0.2 m
BWC-4MNFN3
LMR400, N Male to N Female, 3 m
BWC-4MNFN6
LMR400, N Male to N Female, 6 m
BWC-4MNFN15
LMR400, N Male to N Female, 15 m
BWC-4MNFN30
LMR400, N Male to N Female, 30 m
There is a wide range of antenna cabling available. Please contact Banner Engineering for more information or for specific
lengths and connectors.
Always install and properly ground a qualified surge suppressor when installing a remote antenna system. Remote antenna configurations installed without surge suppressors
located less than 1 meter from the radio device invalidate the Banner Engineering Corp. warranty. Always keep the ground wire as short as possible and make all ground
connections to a single-point ground system to ensure no ground loops are created.
Included with Device
Mounting Hardware Kit
Model
BWA-HW-001
Qty
Item
4
Screw, M5-0.8 x 25mm, SS
4
Screw, M5-0.8 x 16mm, SS
4
Hex nut, M5-0.8mm, SS
4
Bolt, #8-32 x 3/4”, SS
Antenna*
BWA-9O2-C, or
BWA-2O2-C
1
Antenna, 902-928 MHz, 2 dBd Omni, Rubber Swivel RSMA Male, or
Antenna, 2.4 GHz, 2 dBd Omni, Rubber Swivel RSMA Male
DX70 Manual/Data Sheet
133214
1
DX70 Manual/Data Sheet
* Internal antenna devices do not ship with this antenna.
14 P/N 133214 rev. G
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX70 Wireless Systems
FCC Certification 900 MHz
The DX80 Module complies with Part 15 of the FCC rules and
regulations.
FCC ID: TGUDX80 This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may
cause undesired operation.
FCC Notices
IMPORTANT: The DX80 Modules have been certified by the FCC for
use with other products without any further certification (as per FCC
section 2.1091). Changes or modifications not expressly approved
by the manufacturer could void the user’s authority to operate the
equipment.
IMPORTANT: The DX80 Modules have been certified for fixed base
station and mobile applications. If modules will be used for portable
applications, the device must undergo SAR testing.
IMPORTANT: If integrated into another product, the FCC ID label
must be visible through a window on the final device or it must be
visible when an access panel, door, or cover is easily removed. If not,
a second label must be placed on the outside of the final device that
contains the following text: Contains FCC ID: TGUDX80.
Antenna Warning WARNING: This device has been tested with
Reverse Polarity SMA connectors with the antennas listed in Table
1 Appendix A. When integrated into OEM products, fixed antennas
require installation preventing end-users from replacing them with
non-approved antennas. Antennas not listed in the tables must
be tested to comply with FCC Section 15.203 (unique antenna
connectors) and Section 15.247 (emissions).
FCC-Approved Antennas
WARNING: This equipment is approved only for mobile and base
station transmitting devices. Antenna(s) used for this transmitter must
be installed to provide a separation distance of at least 20 cm from all
persons and must not be collocated or operating in conjunction with
any other antenna or transmitter.
DX80 Module may be used only with Approved Antennas that have
been tested with this module.
Part Number Antenna Type
—
Maximum
Gain
Integral antenna
Unity gain
BWA-9O1-x
Omni, 1/4 wave dipole
≤2 dBi
BWA-9O2-C
Omni, 1/2 wave dipole, Swivel
≤2 dBi
BWA-9O6-A
Omni Wideband, Fiberglass Radome
≤8.2 dBi
Note
BWA-9O5-B
Omni Base Whip
≤7.2 dBi
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
BWA-9Y10-A
Yagi
≤10 dBi
Table 1. Type certified Antenna
• Reorient or relocate the receiving antenna,
• Increase the separation between the equipment and receiving
module,
• Connect the equipment into an outlet on a circuit different from
that to which the receiving module is connected, and/or
• Consult the dealer or an experienced radio/TV technician for
help.
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
P/N 133214 rev. G 15
SureCross™ DX70 Wireless Systems
FCC Certification, 2.4 GHz
The DX80 Module complies with Part 15 of the FCC rules and
regulations.
FCC ID: UE300DX80-2400 This device complies with Part 15 of the
FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
FCC Notices
IMPORTANT: The DX80 Modules have been certified by the FCC for
use with other products without any further certification (as per FCC
section 2.1091). Changes or modifications not expressly approved
by the manufacturer could void the user’s authority to operate the
equipment.
IMPORTANT: The DX80 Modules have been certified for fixed base
station and mobile applications. If modules will be used for portable
applications, the device must undergo SAR testing.
IMPORTANT: If integrated into another product, the FCC ID label
must be visible through a window on the final device or it must be
visible when an access panel, door, or cover is easily removed. If not,
a second label must be placed on the outside of the final device that
contains the following text: Contains FCC ID: UE300DX80-2400.
Note
Antenna Warning WARNING: This device has been tested with
Reverse Polarity SMA connectors with the antennas listed in Table
1 Appendix A. When integrated into OEM products, fixed antennas
require installation preventing end-users from replacing them with
non-approved antennas. Antennas not listed in the tables must
be tested to comply with FCC Section 15.203 (unique antenna
connectors) and Section 15.247 (emissions).
FCC-Approved Antennas
WARNING: This equipment is approved only for mobile and base
station transmitting devices. Antenna(s) used for this transmitter must
be installed to provide a separation distance of at least 20 cm from all
persons and must not be collocated or operating in conjunction with
any other antenna or transmitter.
DX80 Module may be used only with Approved Antennas that have
been tested with this module.
Part Number
—
Antenna Type
Maximum
Gain
Integral antenna
Unity gain
BWA-2O2-C
Omni, 1/2 wave dipole, Swivel
≤2 dBi
BWA-2O5-C
Omni, Collinear, Swivel
≤5 dBi
BWA-2O7-C
Omni, Coaxial Sleeve, Swivel
≤7 dBi
Table 1. Type certified Antenna
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna,
• Increase the separation between the equipment and receiving
module,
• Connect the equipment into an outlet on a circuit different from
that to which the receiving module is connected, and/or
• Consult the dealer or an experienced radio/TV technician for
help.
16 P/N 133214 rev. G
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX70 Wireless Systems
Certified Countries List
Models
DX91
Country
Frequency
DX80
DX70
Australia
2.4 GHz
x
x
Austria
2.4 GHz
x
x
x
x
x
Bahamas, The
900 MHz
x
x
x
x
x
Bahamas, The
2.4 GHz
x
x
x
x
x
Bahrain (Kingdom of)
2.4 GHz
x
x
x
x
x
Belgium
2.4 GHz
x
x
x
x
x
Brazil
2.4 GHz
x
x
x
x
Bulgaria
2.4 GHz
x
x
x
x
x
Canada
900 MHz
x
x
x
x
x
Canada
2.4 GHz
x
x
x
x
x
China (People’s Republic of)
2.4 GHz
x
x
Colombia
900 MHz
x
x
x
x
x
Colombia
2.4 GHz
x
x
x
x
x
Cyprus
2.4 GHz
x
x
x
x
x
Czech Republic
2.4 GHz
x
x
x
x
x
Denmark
2.4 GHz
x
x
x
x
x
Estonia
2.4 GHz
x
x
x
x
x
Finland
2.4 GHz
x
x
x
x
x
France
2.4 GHz
x
x
x
x
x
Germany
2.4 GHz
x
x
x
x
x
Greece
2.4 GHz
x
x
x
x
x
Hungary
2.4 GHz
x
x
x
x
x
Iceland
2.4 GHz
x
x
x
x
x
India
2.4 GHz
x
Ireland
2.4 GHz
x
x
x
x
x
Israel
2.4 GHz
x*
x
x*
x
Italy
2.4 GHz
x
x
x
x
x
Latvia
2.4 GHz
x
x
x
x
x
Liechtenstein
2.4 GHz
x
x
x
x
x
Lithuania
2.4 GHz
x
x
x
x
x
Luxembourg
2.4 GHz
x
x
x
x
x
Malta
2.4 GHz
x
x
x
x
x
Mexico
900 MHz
x
x
x
x
Mexico
2.4 GHz
x
x
Netherlands
2.4 GHz
x
x
New Zealand
2.4 GHz
x
x
Norway
2.4 GHz
x
x
x
x
x
Panama
900 MHz
x
x
x
x
x
Panama
2.4 GHz
x
x
x
x
x
Poland
2.4 GHz
x
x
x
x
x
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
DX99
DX80DR
x
x
x
x
x
x
x
P/N 133214 rev. G 17
SureCross™ DX70 Wireless Systems
Country
Frequency
DX80
DX70
Models
DX91
DX99
DX80DR
Portugal
2.4 GHz
x
x
x
x
x
Romania
2.4 GHz
x
x
x
x
x
Saudi Arabia (Kingdom of)
2.4 GHz
x
x
x
x
x
Slovakia
2.4 GHz
x
x
x
x
x
Slovenia
2.4 GHz
x
x
x
x
x
South Africa
2.4 GHz
x
x
Spain
2.4 GHz
x
x
x
x
x
Sweden
2.4 GHz
x
x
x
x
x
Switzerland
2.4 GHz
x
x
x
x
x
Taiwan
2.4 GHz
x**
x
United Kingdom
2.4 GHz
x
x
x
x
x
United States of America
900 MHz
x
x
x
x
x
United States of America
2.4 GHz
x
x
x
x
x
x
x**
* External antenna models
** Only specific models. Refer to certificate for the model list.
Additional Messages
Bulgaria
Authorization required for outdoor and public service use.
France
In Guyane (French Guiana) and La Reunion (Reunion Island),
outdoor use not allowed.
When ordering products for use in France, add -FR to the model
number. For example, the model number for a six discrete I/O
Gateway would be DX80G2M6S6P6-FR.
Italy
If used outside of own premises, general authorization is required.
Luxembourg
General authorization is required for public service.
Canada
This Class A digital apparatus meets all requirements of the Canadian
Interference Causing Equipment Regulations. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Cet appareil numérique de la classe A respecte toutes les exigences
du Règlement sur le matériel brouiller du Canada. Le present appareil
numérique n’emet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numeriques de le Classe A préscrites dans
le Reglement sur le brouillage radioélectrique édits par le ministere
des Communications du Canada.
900 MHz
This device has been designed to operate with the antennas listed on Banner Engineering’s website and having a maximum gain of 9 dBm.
Antennas not included in this list or having a gain greater that 9 dBm are strictly prohibited for use with this device. The required antenna
impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen such that the equivalent isotropically
radiated power (EIRP) is not more than that permitted for successful communication.
It is Banner Engineering’s intent to fully comply with all national and regional regulations regarding radio frequency emissions. Customers who want to re-export this product to a
country other than that to which it was sold must ensure that the device is approved in the destination country. A list of approved countries appears in the SureCross DX80 Wireless
Product Manual, in the Agency Certifications section. The SureCross wireless products were certified for use in these countries using the standard antenna that ships with the product.
When using other antennas, verify you are not exceeding the transmit power levels allowed by local governing agencies. Consult with Banner Engineering if the destination country is
not on this list.
18 P/N 133214 rev. G
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX70 Wireless Systems
Specifications
Radio
Range*
900 MHz: Up to 4.8 kilometers (3 miles)
2.4 GHz: Up to 3.2 kilometers (2 miles)
Transmit Power
900 MHz: 21 dBm Conducted
2.4 GHz: 18 dBm Conducted, ≤ 20 dBm EIRP
Spread Spectrum Technology
FHSS (Frequency Hopping Spread Spectrum)
Antenna Connector
Ext. Reverse Polarity SMA, 50 Ohms
Antenna Max. Tightening Torque
0.45 N•m (4 in•lbf)
Link Timeout
1 or 4 seconds
* With the standard 2 dB antenna. High-gain antennas are available, but the range depends on the environment and line of sight. To determine the range of your wireless
network, perform a Site Survey.
General
Power*
+10 to 30V dc
For European applications: +10 to 24V dc ±10%
Power Consumption
Less than 1.4 W (60 mA) at 24V dc
Mounting
#10 or M5 (M5 hardware included)
M5 Fasteners Max. Tightening Torque
0.56 N•m (5 in•lbf)
Case Material
Polycarbonate
Weight
0.26 kg (0.57 lb)
Indicators
Green/Red Power LED, Yellow/Red Signal LED
External Cable Glands
Two 1/2-inch NPT type
Cable Glands Max. Tightening Torque
0.56 N•m (5 in•lbf)
* For European applications, power the DX70 from a Limited Power Source as defined in EN 60950-1.
Discrete Inputs
Discrete Input Rating
3 mA max current at 30V dc
Discrete Input Sample Rate
62.5 milliseconds
Discrete Report Rate
On Change of State
Discrete Input ON Condition
Sourcing: Greater than 8V
Sinking: Less than 0.7V
Discrete Input OFF Condition
Sourcing: Less than 5V
Sinking: Greater than 2V or Open
Analog Inputs
Two, 0 to 20 mA
Analog Input Rating
24 mA
Analog Input Sample Rate
62.5 milliseconds
Analog Report Rate
1 second or on Change of State (1% change in value)
Accuracy
0.1% of full scale + 0.01% per °C
Discrete Outputs
Four or Eight Sourcing (or Sinking) (depends on kit)
Four or Eight Sourcing (depends on kit)
Discrete Output Rating
100 mA max current at 30V dc
ON-State Saturation: Less than 2V at 100 mA
OFF-State Leakage: Less than 10 µA
Discrete Output ON Condition
Supply minus 2V
Discrete Output OFF Condition
Less than 2V
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
P/N 133214 rev. G 19
SureCross™ DX70 Wireless Systems
Analog Outputs
Two, 0 to 20 mA
Max. End-to-end Latency*
300 milliseconds
Output State Following Timeout
Programmed by DIP switch
* From the sample point and with a good RF signal.
Environmental
Environmental Rating
IEC IP67; NEMA 6
Operating Temperature
−40 to +85° C (Electronics)
Operating Humidity
95% max. relative (non-condensing)
Radiated Immunity
10 V/m, 80-2700 MHz (EN61000-6-2)
Shock and Vibration*
IEC 68-2-6 and IEC 68-2-7
Shock: 30g, 11 millisecond half sine wave, 18 shocks
Vibration: 0.5 mm p-p, 10 to 60 Hz
* Operating the devices at the maximum operating conditions for extended periods can shorten the life of the device.
Compliance
900 MHz Models
FCC ID TGUDX80 - This device complies with FCC Part 15, Subpart C, 15.247
IC: 7044A-DX8009
2.4 GHz Models
FCC ID UE300DX80-2400 - This device complies with FCC Part 15, Subpart C, 15.247
ETSI/EN: In accordance with EN 300 328: V1.7.1 (2006-05)
IC: 7044A-DX8024
For more information:
Contact your local Banner
representative
or
Banner Corporate Offices
around the world.
Asia ─ China
Banner Engineering China
Shanghai Rep Office
Rm. G/H/I, 28th Flr.
Cross Region Plaza
No. 899, Lingling Road
Shanghai 200030 CHINA
Tel: 86-21-54894500
Fax: 86-21-54894511
www.bannerengineering.com.cn
sensors@bannerengineering.com.cn
Corporate Headquarters
Banner Engineering Corp.
9714 Tenth Ave. North
Mpls., MN 55441
Tel: 763-544-3164
www.bannerengineering.com
sensors@bannerengineering.com
Asia ─ Japan
Banner Engineering Japan
Cent-Urban Building 305
3-23-15 Nishi-Nakajima
Yodogawa-Ku, Osaka 532-0011
JAPAN
Tel: 81-6-6309-0411
Fax: 81-6-6309-0416
www.bannerengineering.co.jp
mail@bannerengineering.co.jp
The manufacturer does not take responsibility for the violation of any warning listed in this
document.
CAUTION. Make no modifications to this product. Any modifications to this
product not expressly approved by Banner Engineering could void the user’s
authority to operate the product. Contact the Factory for more information.
Lightning Arrestors/Surge Protection. Always use lightning arrestors/surge protection
with all remote antenna systems to avoid invalidating the Banner Engineering Corp.
warranty. No surge protector can absorb all lightning strikes. Do not touch the SureCross
device or any equipment connected to the SureCross device during a thunderstorm.
P/N 133214 rev. G
Europe
Banner Engineering Europe
Park Lane
Culliganlaan 2F
Diegem B-1831 BELGIUM
Tel: 32-2 456 07 80
Fax: 32-2 456 07 89
www.bannereurope.com
mail@bannereurope.com
Asia
Banner Engineering Asia ─
Taiwan
Neihu Technology Park
5F-1, No. 51, Lane 35, Jihu Rd.
Taipei 114 TAIWAN
Tel: 886-2-8751-9966
Fax: 886-2-8751-2966
www.bannerengineering.com.tw
info@bannerengineering.com.tw
Latin America
Contact Banner Engineering Corp.
(US) or e-mail
Mexico:
mexico@bannerengineering.com
Brazil:
brasil@bannerengineering.com
India
Banner Engineering India
Pune Head Quarters
Office No. 1001
Sai Capital, Opp. ICC
Senapati Bapat Road
Pune 411016 INDIA
Tel: 91-20-66405624
Fax: 91-20-66405623
www.bannerengineering.co.in
india@bannerengineering.com
WARRANTY. Banner Engineering Corp. warrants its products to be free from defects for
one year. Banner Engineering Corp. will repair or replace, free of charge, any product
of its manufacture found to be defective at the time it is returned to the factory during
the warranty period. This warranty does not cover damage or liability for the improper
application of Banner products. This warranty is in lieu of any other warranty either
expressed or implied.
All specifications published in this document are subject to change. Banner reserves
the right to modify the specifications of products, prior to their order, without notice.
Banner Engineering reserves the right to update or change documentation at any time.
For the most recent version of any documentation, please refer to our website: www.
bannerengineering.com. © 2009 Banner Engineering Corp. All rights reserved.
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com