T10 & T11
ORIGINAL
INSTRUCTIONS
Please read these instructions before use.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
T10 & T11
Dear Customer
Thank you for purchasing this Trend product,
we hope you enjoy many years of creative and
productive use.
Please remember to return your guarantee card
within 28 days of purchase.
CONTENTS
TECHNICAL DATA_____________________ 1
SAFETY____________________________ 2-3
ELECTRICAL SAFETY_________________ 4
EC DECLARATION OF CONFORMITY ____ 5
ITEMS ENCLOSED____________________ 5
DESCRIPTION OF PARTS______________ 6-7
ASSEMBLY & ADJUSTMENT
– Switching On & Off____________________ 8
– Depth of Cut_________________________ 8
– Fitting & Removing Cutters_____________ 9
– Speed Control______________________ 10
– Fixing Points for Accessories___________ 10
T10
– Dust Extraction Spout________________ 11
– Fine Height Adjuster Accessory_________ 11
T10 & T11
– Template Guide Bush________________ 12
T11
– Dust Extraction Spout________________ 13
– Fine Height Adjuster__________________ 14
– Accessories________________________ 15
OPERATION
– Cutting Direction & Feed Speed ________ 16
– Side-fence Routing___________________ 17
– Template Guide Bush Routing__________ 18
– Beam Trammel Routing Accessory______ 19
– Bearing Guided Cutters_______________ 20
– Freehand Routing & Batten Routing_____ 21
MAINTENANCE______________________ 22
ENVIRONMENTAL PROTECTION_______ 22
GUARANTEE________________________ 22
SPARE PARTS
– Spare Parts List___________________ 23-26
– Spare Parts Diagram_________________ 27
Definitions: Safety Guidelines
The definitions below describe the level of
severity for each signal word. Please read the
manual and pay attention to these symbols.
WARNING: indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may
result in property damage.
Denotes risk of electric shock.
Denotes risk of fire.
Additional Symbols Used
Wear Personal Protective Equipment (PPE). Ear, eye and respiratory protection must be worn.
Denotes risk of personal injury, loss of life or damage to the tool in case or
non-observance of the instructions in this manual.
For 115 Volt
The 115V router is not supplied with a plug.
We recommend a 32A BS4343 110V plug
is used. Minimum generator or transformer
requirement 3 kVA continuous with a 32A
BS4343 110V socket outlet.
The 115V router cannot be used with a 115V
No-Volt Release Switch.
%
If you require further safety advice,
technical information or spare parts,
please call Trend Technical Support or
visit www.trend-uk.com
T10 & T11
ROUTER
T10E & T11E
TECHNICAL DATA
Voltage UK & Eire VDC230/115
EuropeVDC230
Power input
W
2,000
Power output
W
1,110
No-load speed
min-1 8,000-20,000
Router 2 columns
carriage
Router carriage mm 80
stroke
Revolver
mm
depth stop
Collet size 3-step, with
graduation
& fine
adjustment
INTENDED USE
The router has been designed for professional
heavy duty routing of wood, wood based
materials and plastics.
This router is intended for routing grooves,
edges, profiles and slots as well as copy routing.
At reduced speed with the appropriate router
cutter fitted non-ferrous alloys can also be
routed.
UK & Eire inch 1/2
UK & Eire mm 12.7
Europe mm12
Cutter diameter,T10
max.
T11
mm
50
mm70
Weight
kg5.2
These routers are professional power tools.
Noise values and vibration values
(triax vector sum) according to EN60745-2-17:
LPA (emission sound
pressure level)
dB(A)
LWA (sound power level) dB(A)
KWA (uncertainty for the
given sound level)
Vibration emission
Value ah =
Uncertainty K =
dB(A)
WARNING: The declared vibration emission level
represents the main application of the tool. However
if the tool is used for different applications, with
different accessories or poorly maintained, the
vibration emission may differ. This may significantly
increase the exposure level over the total working
period.
An estimation of the level of exposure to vibration
should also take into account the times when the
tool is switched off or when it is running but not
actually doing the job. This may significantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the
operator from the side effects of vibration such as:
maintain the tool and the accessories, keep hands
warm, organisation of work patterns.
DO NOT use under wet conditions or in
presence of flammable liquids or gases.
92
DO NOT let children come into contact with
this appliance. Supervision is required when
inexperienced operators use this appliance.
100
3.4
This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their safety.
Children should never be left alone with this product.
m/s23.1
m/s21.5
The vibration emission level given in this information
sheet has been measured in accordance with
EN 60745 and may be used to compare one tool
with another. It may be used for a preliminary
assessment of exposure.
-1-
T10 & T11
SAFETY
Keep cord from heat, oil and sharp
5. Consider working environment. Do
edges. Always trail the power cord
not use the product in the rain or in
away from the work area.
a damp environment. Keep work
area
well
lit.
Do
not
use
power
tools
Observe the safety regulations in the
18.Connect dust extraction equipment. near
gasoline
or
flammable
liquids.
instruction manual of the power tool
If devices are provided for the
Keep workshop at a comfortable
to be used. Please read the following
connection of dust extraction and
temperature so your hands are not
instructions carefully. Failure to do so
collection facilities, ensure these are
cold.
Connect
machines
that
are
could lead to serious injury. When using
connected and properly used.
used
in
the
open
via
a
residual
current
electric tools, basic safety precautions,
19.Check all fixing and fastening nuts,
device (RCD) with an actuation
including the following should always be
bolts and screws on power tool,
current of 30 mA maximum. Use only
followed to reduce the risk of fire, electric
attachment and cutting tools before
extension cables that are approved for
shock and personal injury. Also observe
use to ensure they are tight and
outdoor use.
any applicable additional safety rules.
secure. Periodically check when
Read the following safety instructions
6. The accessory or attachment must be
machining over long periods.
before attempting to operate this product.
kept level and stable at all times.
20.Stay alert. Watch what you are doing.
PLEASE KEEP THESE
7. Keep work area clean. Cluttered
Use common sense. Do not operate
INSTRUCTIONS IN A SAFE PLACE.
workshops and benches can cause
tools when you are tired, under the
injuries.
Ensure
there
is
sufficient
The attention of UK users is drawn to The
influence of drugs or alcohol.
room
to
work
safely.
Provision and Use of Work Equipment
21.Personal Protective Equipment (PPE)
Regulations 1998, and any subsequent
8. Secure idle tools. When not in use,
for eye, ear and respiratory protection
amendments.
tools should be stored in a dry and
must be worn. All PPE must meet
high or locked up place, out of reach
Users should also read the HSE/HSC
current UK and EU legislation.
of children.
Safe Use of Woodworking Machinery
22.Do not leave tools running
Approved Code of Practice and Guidance 9. For best control and safety use
unattended. Do not leave tool until it
Document and any amendments.
both hands on the power tool and
comes to a complete stop.
attachment. Keep both hands away
Users must be competent with
from cutting area. Always wait for the 23.Always clamp workpiece being
woodworking equipment before using our
machined securely.
spindle and cutter to stop rotating
products.
before making any adjustments.
24.Only use cutting tools for
IMPORTANT NOTE:
woodworking that meet EN84710.Always keep guards in place and in
Residual Risk. Although the safety
1/2 safety standards, and any
good working order.
instructions and operating manuals for
subsequent amendments.
11.Remove any nails, staples and other
our tools contain extensive instructions
25.Vibration levels. Hand held power
metal
parts
from
the
workpiece.
on safe working with power tools, every
tools produce different vibration
power tool involves a certain residual risk 12.Maintain tools and cutters with care.
levels. You should always refer to
which cannot be completely excluded
Keep cutters sharp and clean for
the specifications and relevant Health
by safety mechanisms. Power tools
better and safer performance. Do
& Safety Guide.
must therefore always be operated with
not use damaged cutters. Follow
caution!
Routing Safety
instructions for lubricating and
changing accessories. Keep handles 1. Read and understand instructions
General
dry, clean and free from oil and
supplied with power tool, attachment
1. Disconnect power tool and attachment
grease.
and cutter.
from power supply when not in
13.Maintain accessories. Do not use
2. Keep hands, hair and clothing clear of
use, before servicing, when making
damaged accessories. Only use
the cutter.
adjustments and when changing
accessories recommended by the
accessories such as cutters. Ensure
3. Remove adjusting keys and
manufacturer.
switch is in “off” position. Always
spanners. Check to see that keys
ensure cutter has stopped rotating.
14.Check damaged parts. Before
and adjusting spanners are removed
operation
inspect
the
attachment,
from the router tool, cutter and
2. Always mount the power tool,
the power tool, the cable, extension
attachment before turning router on.
accessory or attachment in conformity
cable and the plug carefully for signs
Make sure cutter can rotate freely.
with the instructions. Only use
of
damage.
Check
for
alignment
of
attachment and accessories specified
4. Noise. Take appropriate measures
moving
parts,
binding,
breakage,
in the power tool manual. The tool or
for the protection of hearing if
mounting and any other conditions
attachment should not be modified or
the sound pressure of 85dB(A) is
that may effect its operation. Have any
used for any application other than
exceeded. Routing sound pressure
damage repaired by an Authorised
that for which it was designed. Do not
may exceed 85dB(A), so ear
Service
Agent
before
using
the
tool
or
force tool.
protection must be worn.
accessory. Protect tools from impact
3. Keep children and visitors away. Do
5. Eye protection. Always wear eye
and shock.
not let children or visitors touch the
protection in the form of safety
tool, accessory or attachment. Keep 15.Do not use tool if switch does not turn
goggles, spectacles or visors to
it on or off. Have defective switches
children and visitors away from work
protect the eyes.
replaced by an Authorised Service
area. Make the workshop child proof
6. Respiratory protection. Always wear
Agent.
with padlock and master switch.
a face or dust mask, or powered
16.Don’t over reach. Keep proper footing
4. Dress properly. Do not wear loose
respirator. Dust masks/filters should
and balance at all times. Do not
clothing or jewellery, they can be
be changed regularly.
use awkward or uncomfortable hand
caught in moving parts. Rubber
7. Do not switch router on with the cutter
positions.
gloves and non-skid footwear
touching the workpiece. At the end of
is recommended when working
17.Don’t abuse the cable. Never carry
the cut, release the router plunge and
outdoors. Wear protective hair
power tool or accessory by cord or
allow spindle to stop rotating. Never
covering to contain long hair.
pull it to disconnect from the socket.
use the spindle lock as a brake
WARNING:
-2-
T10 & T11
8. The direction of routing must always 9. Cutter shanks should be inserted
into the collet all the way to the line
be opposite to the cutter’s direction of
indicated on the shank. This ensures
rotation. Do not back-cut or climb-cut.
that at least 3⁄4 of the shank length
9. Check before cutting that there are
is held in the collet. Ensure clamping
no obstructions in the path of the
surfaces are cleaned to remove dirt,
router. Ensure there are no obstacles
grease, oil and water.
beneath workpiece when cutting full
fitting a false fence on the back fence.
5. Whenever possible use a work
holding device or jig to secure
component being machined. Ensure
any attachment is securely fitted to
the workbench, with table surface at
approximately hip height.
10.Observe the correct assembly and
6. Use a No-Volt Release Switch. Ensure
fitting instructions in the router
it is fixed securely, easily accessible
instruction manual for fitting the collet,
10.Hold power tool by insulated gripping
and used correctly.
nut and cutter.
surfaces, because the cutter may
7. In router table (inverted) mode, stand
contact its own cord. Cutting the “live” 11.Tool and tool bodies shall be clamped
to the front right of the table. The
in such a way that they will not
wire may make exposed metal parts
cutter will rotate anti-clockwise when
become loose during operation. Care
of the powertool “live” and shock the
viewed from top so the feed direction
shall be taken when mounting cutting
operator.
is from the right (against the rotation of
tools
to
ensure
that
the
clamping
is
by
11.Use clamps or another practical way
the cutter). In overhead mode, stand to
the shank of the cutting tool and that
to secure and support the workpiece
the front left of the machine table and
the cutting edges are not in contact
to a stable platform. Holding the work
the feed direction is from the left.
with
each
other
or
with
the
clamping
by your hand or against the body
8. Do not reach underneath table or put
elements.
leaves it unstable and may lead to
your hands or fingers at any time in
12.It is advisable to periodically check
loss of control.
the cutting path while tool is connected
the collet and collet nut. A damaged,
to a power supply.
Router Cutter Safety
worn or distorted collet and nut can
1. Cutting tools are sharp. Care should
9. Never thickness timber between the
cause vibration and shank damage.
be taken when handling them. Do not
back of the cutter and the backfence.
Do not over-tighten the collet nut
drop cutters or knock them against
13.Do not take deep cuts in one pass;
Useful Advice When Routing
hard objects. Handle very small
take several shallow or light passes
1. Judge your feed rate by the sound
diameter cutters with extra care.
to reduce the side load applied to the
of the motor. Feed the router at a
Always return cutter to its packaging
cutter
and
router.
Too
deep
a
cut
in
constant feed rate. Too slow a feed
after use.
one pass can stall the router.
rate will result in burning.
2. Always use cutters with a shank
diameter corresponding to the size of 14.In case of excessive vibrations whilst 2. Trial cuts should be made on waste
using the router stop immediately and
material before starting any project.
the collet installed in your tool.
have the eccentricity of the router,
3. When using some attachments e.g.
3. The maximum speed (n.max) marked
router cutter and clamping system
a router table or dovetail jig, a fine
on the tool, or in instructions or on
checked by competent personnel
height adjuster is recommended.
packaging shall not be exceeded.
15.All fastening screws and nuts should
Where stated the speed range shall
4. When using a template guide bush,
be
tightened
using
the
appropriate
be adhered to. Recommended speeds
ensure there is sufficient clearance
spanner or key and to the torque
are shown in the Trend Routing
between cutter tip and inside edge
value provided by the manufacturer.
Catalogue and/or website.
of bush and that it cannot come into
16.Extension
of
the
spanner
or
tightening
contact with collet and nut. Ensure
4. Always use router cutters in a router.
using
hammer
blows
shall
not
be
cutter and guide bush are concentric.
Drill and boring bits must not be
permitted.
used in a router. Router cutters
Router Cutter Repair/Maintenance
17.Clamping screws shall be tightened
must only be used for the material
according to instructions provided by 1. Repair of tools is only allowed in
cutting application for which they are
accordance with the manufacturers
the manufacture. Where instructions
designed. Do not use on metal or
instructions.
are not provided, clamping screws
masonry.
shall be tightened in sequence from
2. The design of composite (tipped)
5. Never use cutters with a diameter
the centre outwards.
tools shall not be changed in process
exceeding the maximum diameter
of repair. Composite tools shall be
indicated in the technical data of the 18.Do not touch the cutter immediately repaired by a competent person i.e.
after operation; it may be extremely
powertool or attachment used.
a person of training and experience,
hot and could burn your skin.
6. Before each use check that the
who has knowledge of the design
cutting tool is sharp and free from
Using Routers In A Fixed Position
requirements and understands the
damage. Do not use the cutting tool
levels of safety to be achieved.
1. Attention should be made to the
if it is dull, broken or cracked or if in
3. Repair shall therefore include, e.g.
HSE’s Safe Use of Vertical Spindle
any other damage is noticeable or
the use of spare parts which are in
Moulding Machines Information Sheet
suspected.
accordance with the specification
No.18 and any revisions.
7. Cutters should be kept clean. Resin
of the original parts provided by the
build up should be removed at regular 2. After work, release the router plunge
manufacturer.
to protect the cutter.
intervals with Resin Cleaner. The use
4. Tolerances which ensure correct
of a PTFE dry lubricant will reduce
3. Always use a push-stick or pushclamping shall be maintained.
resin build up. Do not use PTFE spray
block when making any cut less than
on plastic parts.
300mm in length or when feeding the 5. Care shall be taken that regrinding
of the cutting edge will not cause
last 300mm of the cut.
8. When using stacked tooling (multiweakening of the body and the
blade, block and groover etc.) on a
4. The opening around the cutter should
connection of the cutting edge to the
spindle arbor, ensure that the cutting
be reduced to a minimum using
body.
edges are staggered to each other to
suitably sized insert rings in the table
reduce the cutting impact.
and closing the back fence cheeks or
Version 8.0 08/2017
thickness, and that a sacrificial work
surface is used.
-3-
T10 & T11
ELECTRICAL SAFETY
Power Supply
The electric motor has been designed for one
voltage only. Always check that the power
supply corresponds to the voltage on the rating
plate. Machines marked for 230 volt can also be
operated from a 220 volt supply.
For 115V units with a power rating exceeding
1500W we recommend to use a plug to BS4343
standard. For T10 & T11 this must be rated to 32A.
WARNING: Never use a light socket.
Never connect the live (L) or neutral (N)
wires to the earth pin marked E or .
The T10 & T11 is double insulated in
accordance with EN 60745; therefore no
earth wire is required.
Using an Extension Cable
n If an extension cable is required, use an
approved triple core extension cable suitable for
the power input of this tool (see technical data).
Mains Plug Replacement
(UK & Ireland only)
n When using a cable reel, always unwind the
cable completely.
Always check the condition of the cable and plug
before starting with your work.
n Also refer to the table below.
Should your mains plug need replacing and you
are competent to do this, proceed as instructed
below. If you are in doubt, contact an authorised
Trend repair agent or a qualified electrician.
Conductor size (mm2) Cable rating (Amperes)
0.756
1.0010
1.5015
2.5020
4.0025
n Disconnect the plug from the supply.
n Cut off the plug and dispose of it safely;
a plug with bared copper conductors is
dangerous if engaged in a live socket outlet.
n Only fit 13 Amperes BS 1363A approved
plugs fitted with a 13 Amp A.S.T.A approved
BS 1362 fuse (1).
Voltage
115
230
n The cable wire colours, or a letter, will be
marked at the connection points of most
good quality plugs. Attach the wires to their
respective points in the plug (see below).
Brown is for Live (L) (2) and Blue is for
Neutral (N) (3).
nBefore replacing the top cover of the mains
plug ensure that the cable restraint (4) is
holding the outer sheath of the cable firmly
and that the two leads are correctly fixed at
the terminal screws.
13 AMP
1
2
Cable length (m)
7.515 25 30 45 60
Amperes
Cable rating (Amperes
0 - 2.0
6 6 6 6 6 10
2.1 - 3.4
6 6 6 6 15 15
3.5 - 5.0
6 6 10 15 20 20
5.1 - 7.0
10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 12.1 - 20.0 20 20 25 - - 0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
6
6
6
10
15
20
6
6
6
10
15
20
6
6
6
10
15
20
6
6
6
10
15
20
6
6
10
15
20
25
6
6
15
15
20
-
WARNING: 115V units have to be
operated via a fail-safe isolating
transformer with an earth screen
between the primary and secondary
winding.
3
4
-4-
T10 & T11
EC DECLARATION OF
CONFORMITY
MACHINERY DIRECTIVE
Additional Specific Safety Rules for
Cutters
n Hold power tool by insulated gripping
surfaces, because the cutter may contact
its own cord. Cutting a “live” wire may make
exposed metal parts of the power tool “live”
and shock the operator.
ROUTER
T10E & T11E
n Use the clamps or another practical way to
secure and support the workpiece to a stable
platform. Holding the work by your hand or
against the body leaves it unstable and may
lead to loss of control.
Trend declares that these products described
under Technical Data are in compliance with
2006/42/EC, EN 60745-1:2009 + A11:2010,
EN 60745-2-17:2010.
n For personal protection, ALWAYS wear a dust
mask.
These products also comply with Directives,
2014/30/EU and 2011/65/EU.
n Always use cutters suitable for a speed of
30,000 min and marked accordingly.
For more information please contact Trend at the
following address or refer to back of manual.
The undersigned make this declaration on behalf
of Trend Machinery & Cutting Tools Ltd.
n Never use cutters with a diameter exceeding
the maximum diameter indicated in the
Technical Data.
WARNING: We recommend the
use of a residual current device
with a residual current rating of
30mA or less.
Managing Director
Jeff Willcocks
This router is designed to accept professional
cutters of straight, profile, rabbet, and grooved
type with rated minimum speed of 30,000 min.
Trend Machinery & Cutting Tools Ltd
Unit 6 Odhams Trading Estate
St Albans Road, Watford
Herts, WD24 7TR
United Kingdom
25.08.2017
WARNING: Always consider
the following compulsive
conditions:
n Use 12.7mm shank diameter for straight,
rabbet, groove and profile cutter.
n Maximum cutter diameter:
RESIDUAL RISKS
In spite of the application of the relevant safety
regulations and implementation of safety devices,
certain residual risks cannot be avoided. These
are:-
T10/T11 50mm at 35mm cutting depth
T10/T11 Groove Cutter:
50mm at 6mm cutting depth
MARKINGS ON TOOL
Impairment of hearing.
Risk of personal injury due to flying particles.
The following pictures are shown on the tool.
Risk of burns due to accessories becoming hot during operation.
Read instruction manual before use.
Risk of personal injury due to prolonged use.
Date Code Position
-5-
xxxx xx xx
The date code which
includes the year of
manufacture is printed
into the housing.
4
xxxx xx xx
■
■
■
■
4
T10 & T11
B
I
ITEMS ENCLOSED
G
R
T10 & T11
4
D
1 x Parallel side-fence with micro adjuster
H
1 x Fence rods (pair)
A
C
1 x Collet 1/2” (12.7mm) UK & Eire (Europe 12mm)
P
1 x Spanner (22mm A/F)
E
Q
1 x Guide bush 30mm and fixing screws
1 x Inner plate and fixing screws
K
1 x Line-up pin 12mm/1/2”
F
J
1 x Dust extractor spout with fixing screws
1 x Dust extractor spout clip
X
1 x Instruction manual
L
1 x Guarantee registration card
N
M
AD
O
AC
AF
T11 only
AH
1 x Fine height adjuster handle
■ Check for damage to the tool, parts or accessories which may have occurred during transport.
■ Take the time to thoroughly read and understand this manual prior to operation.
AG
AB
AA
Y
AE
U
Z
DESCRIPTION OF PARTS T10
W
A Plunge locking lever
B Variable speed control dial
C Handle
D Switch
E Depth stop locking knob
F Depth stop micro adjuster
G Depth stop height adjuster dial
H Depth stop scale
I Depth stop lens
J Thumb knob with anti-vibration spring
for side fence
K Collet nut
L Spindle lock
MBase
N 3-way turret stop
OCollet
P Knurled nut
Q Threaded spindle
R Threaded spindle cap nut
V
S
T
U
V
W
X
Y
Z
AA
AB
AC
AD
AE
AF
AG
AH
-6-
Template guide bush dia. 30mm
Template guide fixing screw
Fence rods dia. 10mm x 360mm
Parallel side fence
Parallel side fence micro adjuster knob
Spanner (22mm A/F)
Dust spout 35mm dia.
Dust spout fixing screws
Dust spout fixing nut
Dust spout insert
Dust spout top clip
Dust spout top clip screw
Dust Spout underside clip
Template guide bush line-up pin
Inner plate fixing screws
Inner plate
T10 & T11
DESCRIPTION OF PARTS T11
A Plunge locking lever
B Variable speed control dial
C Handle
D Switch
E Depth stop locking knob
F Depth stop micro adjuster
G Depth stop height adjuster dial
H Depth stop scale
I Depth stop lens
J Thumb knob with anti-vibration spring
for side fence
K Collet nut
L Spindle lock
MBase
N 3-way turret stop
OCollet
P Knurled nut
Q Threaded spindle
R Threaded spindle hex cap nut
S Template guide bush dia. 30mm
T Template guide fixing screw
U Fence rods dia. 10mm x 360mm
V Parallel side fence
W Parallel side fence micro adjuster knob
X Spanner (22mm A/F)
Y Dust spout 35mm dia.
Z Dust spout fixing screws
AA Dust spout fixing nut
AB Dust spout insert
AC Dust spout top clip
AD Dust spout top clip screw
AE Dust spout underside clip
AF Quick release jig & table aperture
AG Clamp guide system fitting
AH Inner plate
AI Inner plate fixing screw
AJ Fine height adjuster handle
AK Template guide bush line-up pin
AL Fine height adjuster handle dial
B
AJ
I
AL
G
R
4
D
H
A
C
P
E
Q
F
K
AF
J
X
L
M
AG
N
AK
O
AH
AD
AC
AB
AI
AA
Y
S
AE
T
U
Z
W
V
-7-
T10 & T11
ASSEMBLY & ADJUSTMENT
n Read the depth of cut using the measuring
lens (5) and scale.
Switching On & Off
n Adjust the depth of cut to the millimetre using
the knob (6).
n On; pull the switch up.
n Off; press the switch down.
ON
I
OFF O
ON
OF
F
5
6
4
I
O
4
Adjusting the Depth of Cut
2
n Place the machine with cutter fitted on to the
workpiece.
n Pre-set the 3-way turret stop (1) as required.
3
n Undo the thumb knob (2) for securing the depth
stop (3).
n Lift up the plunge locking lever (4) for fixing the
depth.
n Lower the machine slowly until the cutter
touches the workpiece and secure it with the
locking lever.
1
n Set the measuring lens (5) to a round figure
or zero.
n Adjust the depth of cut using the knob (6) and
the measuring lens (5).
n Rotate the knob (6) until the depth stop micro
adjuster (3) touches the revolving depth stop (1).
The distance between the top of the revolving
depth stop and the bottom of the depth stop is
the required depth of cut.
n Tighten the knob (2).
WARNING: Never make adjustments
when the router is running or
plugged in.
The rotating turret stop screws can be used
for pre-setting up to three depths of cut. Their
height can be adjusted using a screwdriver (7)
and an 8mm A/F spanner (8).
WARNING: Deep cuts should always
be routed in several passes.
CAUTION: When in plunging mode
By turning the
turret stop, three
depth settings
can be quickly
made.
never release the plunge lever without
the base of the router supported on a
flat surface as this may damage the
router housing or could cause injury.
7
8
If the depth of cut needs re-adjustment, it is
recommended to use the depth stop micro
adjuster.
1
n Adjust the depth of cut using the depth stop
micro adjuster (3). One turn corresponds to
approximately 1mm.
-8-
T10 & T11
How to Fit and Remove a Router
Cutter
4
Fitting Cutters
n Insert at least 3/4 of the shank length of the
cutter (1) into the collet.
n Press the spindle lock (2) forward until the
router spindle is locked (you may need to turn
the spindle slightly to engage it).
n Tighten the collet nut with a spanner (3). Do
not use excessive force.
Removing Cutters
n Undo the 22mm A/F collet nut with the
spanner.
2
3
n Keep turning the spanner until the collet nut
tightens and then loosens again. This is the
fail-safe mechanism releasing the collet.
n The cutter should now slide out.
n Each time you finish using a cutter, remove it
and store it in a safe place.
1
Correct Sequence for Fitting Collet,
Nut and Cutter
WARNING: Do not tighten the collet
without a cutter fitted.
WARNING: Always use cutters with
shanks which match the diameter of
the collet.
(1)
WARNING: Do not use cutters larger
than 45mm unless the router is fitted
in a router table.
(2)
CLICK
CAUTION: Care should be taken when
removing cutter to avoid cuts to
fingers.
ELU
no/project no: 122280/170201
20.03.1997
Collet can be removed from
collet nut.
(3)
ng no/archive no: 170201/122280_TB
n no: 1
ator: KS Cheung
ption:
-9-
T10 & T11
Setting the Electronic Speed Control Dial
The speed is infinitely variable from 8,000 to
20,000 rpm using the electronic speed control
dial (1) for uniform cutting results in all types of
wood, plastics and in aluminium.
1
n Turn the electronic speed control dial to the
required level. The dial is numbered from 1
to 5 and corresponds to router speeds from
8,000 rpm to 20,000 rpm.
5
n Generally, use the lower settings for large
diameter cutters and the higher settings for
small diameter cutters. The correct setting will
also depend on the density of the material,
depth of cut and feed speed of the router, as
severe loss of rpm denotes motor overload.
DialRouter
Using a Fine Height Adjuster
No.
The T10 has an optional fine height adjuster
accessory Ref. FHA/003 and the T11 has a
built in fine height adjuster called the Quick
Raiser. These should be used when fine height
adjustment of the cutter is required. This is
especially recommended when using dovetail
jigs or router tables.
1
2
3
4
5
Speed
8,000
12,000
16,000
18,000
20,000
rpm
rpm
rpm
rpm
rpm
Parallel Side-fence Assembly
6
7
8
Assemble side-fence as shown.
115mm
Fixing Points for Accessories
The router has three threaded holes M6 in its
base that allow fitting of accessories and also
fitting to router tables.
A whole range of accessories are shown in the
Trend Routing Catalogue.
M6
15mm
75mm
-10-
T10
T10
Fitting and Removing T10
Dust Extractor Spout
6
5
The dust extraction spout consists of a main
section (1) with underside clip (7), an insert cover
(2), top clip (5) with screw (6), two main screws
(3) & two nuts (4).
n Check underside clip (7) is fitted into main
section. Slide the insert cover (2) onto the
main section if required (1) and click into
place.
35mm
n Fit nuts (4) into main body. Place spout into
base of router and secure with two screws (3).
n Connect a dust extractor hose to the dust
extraction spout (1).
2
n The top clip (5) can be used with hoses that
have a removable adapter fitted. Loosen the
screw in the top of the router and fit the top
clip (5) as shown using screw (6).
4
1
3
7
WARNING: Whenever possible use
the dust extraction spout with a
suitable extractor when routing.
1
NOTICE: Top clip (5) cannot be
used with vacuum extractor hoses
with a permanent adapter fitted.
2
Fitting the T10 Fine Height Adjuster
Optional Accessory Ref. FHA/003
5
n Plunge router and lock lever (6) down.
n Remove hex cap (5) nut from threaded
stud (3), using a 19mm A/F spanner.
4
n Remove knurled ring nut (4) from
threaded stud (3).
3
n Place washer (2) on threaded stud.
n Thread on main adjuster rod (1) for at
least 25mm of thread.
-11-
4
6
T11
T10 & T11
Fitting Template Guide Bush
and Inner Plate
7
The routers have a unique built-in line up
system for the template guide bush. This
system ensures that the guide bush is exactly
concentric to the router cutter to ensure
accurate work.
3
6
n Turn the router upside down.
n Fit inner plate (2) into the recess in the router
base plate (1). For T10 the bushes on the
inner plate must be towards the router motor.
For T11 the raised side of the inner plate
must be away from router base. Loosely fit
the two pan head machine screws (3) through
the inner plate and into the tapped holes.
DO NOT TIGHTEN SCREWS.
n Fit the 30mm template guide bush (6) to the
inner plate (2). Fit guide bush with the two
M5 countersink machine screws (7). Tighten
these screws.
n The line up pin (5) is stepped for 12mm and
1
/2” collet (4) sizes. (For the 1/2” collet simply
push the line up pin further down into the 1/2”
collet).
n Fit line up pin (5) into the 1/2” collet (8) (or
12mm depending on the size fitted) in the
router, lightly tighten collet nut to hold the line
up pin (5).
n Release plunge lever and gently depress
base until line up pin (5) projects through the
30mm guide bush (6).
n Once in line, tighten the pan head machine
screws (3) with a flat screwdriver.
-12-
5
2
1
4
T11
T11
Fitting Dust
Extractor Spout
Fitting and Removing T11
Dust Extractor Spout
The dust extraction spout consists of a main
section (1) with underside clip (7), an insert
cover (2) and top clip (5) with screw (6).
A
n Check underside clip (7) is fitted into main
section. Slide the insert cover (2) onto the
main section if required (1) and click into
place.
3
B
n Clip into the base by pushing down the dust
extraction spout (1) until clips engage in the
recess.
Removing Dust
Extractor Spout
n Connect a dust extractor hose to the dust
extraction spout (1).
n The top clip (5) can be used with hoses that
have a removable adapter fitted. Loosen the
screw in the top of the router and fit the top
clip (5) as shown using screw (6).
4
2
C
1
B
n To remove dust extraction spout, push spout
(1) to side and pivot out.
3
A
7
For more permanent fixing, fit nuts (4) into main
body, place spout into base of router and secure
with two screws (3).
WARNING: Whenever possible
use the dust extraction spout
with a suitable extractor when
routing.
Top clip (5) cannot be used with
vacuum extractor hoses with a
permanent adapter fitted.
Using the T11 Without Fine
Height Adjuster
2
In portable use the knurled nut (2) should be
wound to the top of the stud and hand tighten
against the hex cap. The base of the knurled
nut (4) should be aligned with the forks (3) in
the router casting.
4
4
3
CAUTION: In normal plunge mode,
ensure the base of the knurled nut
is aligned correctly with the forks
of the lower motor housing. This
will enable the cutter to retract
into the base safely.
8
-13-
3
T11
Fitting the T11 Fine Height Adjuster
The fine height adjuster (Quick Raiser) for the
T11 can be used portably or when the router is
held inverted in a table. If a suitable size access
hole is drilled into the router table top, the height
adjustment can also be adjusted from above the
table top.
Portable Use
5
To set up for fine height adjustment:
7
n Plunge router and lock lever down (1).
6
n Rotate the knurled nut (2) down the stud until
it is close to the router casting forks (3).
4
1
n Align the base of the knurled nut (4) so that it
will locate in the forks (3).
n Release plunge locking lever (1).
8
3
CAUTION: Do not use a powered
drill to drive the T11 Quick Raiser
assembly. Only use the supplied
handle. Ensure that the plunge
locking lever is unlocked. Never use
unnecessary force to rotate the Quick
Raiser mechanism. Do not undo Torx®
screw on hex nuts.
For Portable Use
n Place the fine height adjuster handle (5) onto
the top threaded spindle hex nut (6).
2
3
4
Inverted Use
0.1
0.5
n Rotate handle clockwise to raise motor body
and reduce cutter depth.
n Rotate handle anti-clockwise to lower motor
body and increase cutter depth.
0
1.5
5
7
For Router Table Use
n Ensure router is fitted into the router table
(10), see opposite page.
n Place fine height adjuster handle (5) through
router table cutter hole onto bottom threaded
spindle hex nut (9).
68mm
n Rotate handle clockwise to raise motor body
and raise cutter height.
36mm
9
n Rotate handle anti-clockwise to lower motor
body and lower cutter height.
One revolution corresponds to 1.5mm. The height
adjuster handle dial (7) can be reset to zero.
10
-14-
T11
Modification of User Router Table for
T11 Fine Height Adjuster
To use fine height adjuster in table mode a
20mm diameter hole is required to be drilled
into the router table top. To position the hole it
is advisable to remove the phenolic base slider
of the T11 router and use it as a template.
n Mark the hole for the handle height adjuster
in the table top using the phenolic base
slider as a template.
n Remove the phenolic base slider.
n Mark with a punch the centre of the hole.
n Drill a pilot hole in the centre.
n Enlarge the hole to 20mm.
n Remove any burrs.
2
A template is provided on page 28.
Table Use
Top View
T11 Quick Release Fixing Kit
Optional Accessory Ref. T11/JT/KIT
The T11 Quick Release Fixing Kit uses three
cams (1) to lock the router into a router table.
The kit can be retro-fitted to user-made tables
by drilling suitable size holes in a set pattern
into the table surface. The kit comprises three
cams, three bosses, three springs and three
nut & bolt assemblies. The kit is supplied with
instructions for drilling and using the cams. The
cams locate into the three apertures (2) in the
base of the T11 router.
4
WARNING: When using large panel
raiser cutters, making deeps or if
the router is to be used inverted for
long periods, the router should also
be secured using three M6 machine
screws into the TBC router fixing
holes.
3
T11 Clamp Guide System Optional
Accessory Ref. T11/CGS/KIT
The T11 has two M6 tapped holes in the upper
face of the router base (3), which will accept
the Clamp Guide System accessory (4). The
accessory is used with the Clamp Guide
System clamps (5) and is used to create parallel
grooves and trenches.
4
-15-
5
T10 & T11
OPERATION
Feed Speed
WARNING: To reduce the risk of
serious personal injury, always
use proper hand position as
shown.
The speed at which the cutter is fed into the
wood must not be too fast that the motor slows
down, or too slow that the cutter leaves burn
marks on the face of the wood. Practice judging
the speed by listening to the sound of the motor
when routing.
WARNING: To reduce the
risk of serious personal
injury, always hold securely
in anticipation of a sudden
reaction.
Sequence of plunging
Proper hand grip
requires one hand
on each grip as
shown.
Step One
Plunge down and lock the motor
carriage, by depressing the
plunge locking lever.
Step Two
Carry out the routing operation.
Cutting Direction
WARNING: The direction of routing
must always be opposite to the
cutter’s direction of rotation.
Otherwise there is a risk of kick-back.
Step Three
Release the plunge locking lever
and the motor carriage returns to
the normal position.
Feed direction
of router
When routing always lock the
plunge locking lever.
Direction of
cutter rotation
Feed Direction
Moulding Natural Timbers
When edge moulding natural timbers, always
mould the end grain first, followed by the long
grain. This ensures that if
there is ‘breakout’, this
will be removed when
2
the long grain is routed.
When routing along an edge, the direction of
the router travel should be against that of the
rotation of the cutter. This will create the correct
cutting action and prevent the cutter ‘snatching’.
It will also pull the router towards the workpiece
and hence the side-fence or guide bearing will
be less likely to wander from the edge of the
workpiece.
3
-16-
4
1
T10 & T11
Side-Fence Routing
B
The side-fence is used to guide the router
when moulding, edge profiling or rebating
the edge of the workpiece or when routing
grooves and slots in the centre of the
workpiece, parallel to the edge.
7
The edge of the workpiece must be straight
and true. The cheeks are adjustable and
should be set ideally with a 3–4mm gap
each side of the cutter.
9
3
2
A
4
Fitting and using the Side Fence
n Make sure the thumb knobs (3) are fully
released. Slide the guide rods (1) into the
routing base (2) and tighten the thumb
knobs (3).
n Adjust the side-fence (4) to the required
distance and clamp in place with the thumb
knobs (3).
8
1
6
n Feed along the timber, keeping sideways
pressure (A) to ensure the side fence does
not wander away from the workpiece edge
and downward pressure on the inside hand
(B) to prevent the router from tipping.
n When finished, raise the router, secure with
the plunge locking lever (9) and switch off.
n Then lower the cutter height until the cutter
is just above the workpiece.
n Fine adjustments are possible by slackening
the underside locking knob (8), adjusting the
micro-adjustment knob (6) and securing it
again with the knob (8). One revolution of the
micro-adjustment knob (6) equals 1.0mm of
side-feed.
When starting the cut,
keep the pressure on the
front cheek (C) until the
back cheek contacts the
workpiece edge.
C
n Lower the cutter onto the workpiece and set
the cutter height by raising the depth stop (7)
the required distance.
At the end of the cut, keep
pressure on the back cheek
(D) until the cut is finished.
This will prevent the router
cutter swinging in at the
end of the workpiece and
‘nipping’ the corner.
n Switch on the router and when the cutter
reaches full speed, gently lower the cutter
into the workpiece and lock the plunge.
-17-
D
T10 & T11
Routing with a Template
The guide bush is used in conjunction
with a template when the routing
operation is repetitive or the workpiece
is complex in shape. The template
is fixed to the upper surface of the
workpiece. A cutter is chosen with a
diameter which will pass through the
centre of the bush leaving enough
clearance. The cutter can be straight
or shaped. The router can then be
guided around the template so that
the shape of the template will be
replicated.
Making the Template
The template is cut from 6mm or 1/4”
MDF, plywood or plastic to the shape
required. The guide bush offset needs
to be allowed for when calculating the
shape of the template. The template
must be smaller by an amount equal to
the difference between the ‘outer edge
of the guide ring’ and the ‘outer edge
of the cutter’. See below for the offset
calculation. The edge of the template
must be free of imperfections as these
will be replicated in the final workpiece.
Using a template to rout a straight edge
Calculations for template offset
Template
Alternatively it can
be used for cutting
shapes or making
panelling grooves.
d
D
Template
guide bush
Workpiece
Guide bush
fitted to
router
E
Template
Guide
bush ring
Cutter
FORMULA
(D- d)
E=
2
-18-
T10 & T11
Beam Trammel Routing
Optional Accessory
Ref. BEAM/002
2
Cutting Arcs with the Router
n Fit the beam trammel (1) to the router
base (3).
5
n Place the machine on the workpiece
and ensure pin on beam trammel will
pierce the workpiece surface.
n Measure the radius and fix the point
of the beam trammel in position.
n Fasten the beam trammel (1) in the
routing base (3) with the thumb knob
(4).
n Set the cutting depth using
the depth stop dial (2).
n Switch on the machine.
n After releasing the plunge locking
lever (5), lower the machine slowly as
far as the depth stop and lock it there.
n Cut grooves, rebates etc. at a steady
rate of feed, in an anti-clockwise
direction.
4
1
n When finished, release plunge locking
lever (5) to raise the machine.
n Switch off the machine.
-19-
3
T10 & T11
Bearing Guided Cutter Routing
Edge profiling and shaping cutters are available
with a bearing fitted to the end. This enables
shaped or straight workpieces to be routed
without the need for a guiding device such as a
side-fence or batten.
1
The edge must be free from imperfections
as these will be reflected in the finish of the
mould. Often alternative diameters of bearings
are offered which will change the shape of the
resulting mould.
With certain shapes such as the chamfer cutter
below, increasing the depth of cut will produce a
larger chamfered edge.
n Fit the bearing guided cutter into the router
collet.
n Place router onto the workpiece.
n Set height of cutter using the depth stop (1).
n Switch on the machine.
n After releasing the plunge locking lever, lower
the machine slowly as far as the depth stop.
The guide bearing
ensures the cutter
follows the workpiece.
n With bearing of cutter running along board
edge, mould the edge of the workpiece by
moving the router in the direction shown.
n A continuous motion should be used to
prevent burning of the workpiece. When
possible, take a number of passes at
increased cutter depths. A light final pass will
produce a good finish.
n When complete, retract the carriage by
releasing the plunge locking lever.
n Switch off the router.
Where the material thickness leaves
insufficient room for the bearing to make
contact, a second piece of material can
be temporarily fixed beneath it for the ball
bearing to follow.
CAUTION: Keep downward pressure
with the inside hand to prevent the
router from tipping.
-20-
T10 & T11
Freehand Routing with the Router
The router can also be used for sign
writing or creative freehand work without
any form of guide.
With practice, numbers or name plate
designs can be routed freehand. Draw the
design or motif on the workpiece and then
rout the design, taking shallow passes.
A v-groove cutter is
ideal for engraving
designs at shallow
depths.
Clamp Guide and Batten Routing
Where a side fence cannot be used, it is also
possible to guide the router along a Clamp
Guide or batten clamped across the workpiece.
The Clamp Guides have built in clamping.
Use the straight edge of the router base and
calculate the distance required from the edge
of the Clamp Guide to the cut required.
After use, remove all accessories, and return
tool to its packaging.
Optional Accessories
Standard technique is used,
and side pressure applied to
ensure the router does not
wander from the Clamp Guide.
Since accessories other than those offer
by Trend, have not been tested with this
product, use of such accessories with this
tool could be hazardous. To reduce the
risk of injury only Trend, recommended
accessories should be used with this product.
Please use only Trend original accessories.
-21-
T10 & T11
MAINTENANCE
Lubrication
n The bearings of the machine need no
lubrication, as they are sealed. The two
plunge columns on the routing base should
be slightly oiled from time to time.
Cleaning
n Keep the machine clean at all times. Some
maintenance products and solvents may
damage the plastic parts, these include
products containing Benzene, Trichloroacetyl
Chloride and Ammonia.
n Keep the cooling vents on the motor housing
clean and unobstructed at all times. Blow
out any dust and dirt at regular intervals.
n Visually check the carbon brushes. In the
event of excessive sparking, they may need
changing.
n Never use any caustic agents to clean the
plastic parts.
Changing Brushes
n After about 40 operating hours inspection
by a authorised Trend service agent is
recommended.
WARNING: Ensure machine is isolated
from power supply.
Storage
n After use return the tool to its storage case.
The carbon brushes will need replacing when
they become worn to a certain limit.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing
as waste.
Accessories and packaging should be sorted
for environmental-friendly recycling.
IC
N
O
TR
EC
Separate collection.
This product must not be disposed of
with normal household waste.
EL
Household User
Local regulations may provide for separate
collection of electrical products from the
household, at municipal waste sites or by
retailer when you purchase a new product.
WARNING: It is advisable to have the
brushes replaced by an authorised
Trend Service Agent. The router will
also be given a thorough inspection.
Please call Trend Customer Services for
advice as to how to dispose of unwanted Trend
electrical products in an environmentally safe
way or visit www.trend-uk.com
n Undo the two screws and take off the top
cover. Then undo the two screws and move
variable speed control out of the way.
n Undo the screws holding the brush holder
clamp and remove holder with brush.
Business Users
Please call Trend Customer Services for
disposal of unwanted Trend electrical products.
n Remove leads, pull on brush tab and remove
brush and fit new brush into holder. Then
refit lead and replace brush assembly into the
housing.
GUARANTEE
n Refit brush holder cover and screws.
n Refit speed control to position and secure with
screws and replace cover and secure with
screws.
n Always use original T10/T11 spare parts.
The unit carries a manufacturers guarantee in
accordance with the conditions on the enclosed
guarantee card.
For the location of your nearest Trend Service
Agent, please call Trend Customer Services or
see our stockist locator at www.trend-uk.com.
-22-
T10 & T11
Please use only Trend original spare parts.
T10 & T11- SPARE PARTS LIST
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
v5.0 04/2015
Qty. Desc.
1
1
1
1
1
1
1
1
1
2
2
2
2
1
1
1
2
2
1
1
1
2
2
2
2
1
1
1
1
2
4
1
1
1
2
1
1
4
4
2
1
1
Ref.
Armature 115V T10/T11EL c/w Fan >10/09 to 07/15 WP-T10EL/001A
Armature 240V T10/T11E c/w Fan >10/09 to 07/15 WP-T10E/001A
Armature 115V T10EL & T11EL c/w Fan >08/15
WP-T10EL/001B
Armature 230V T10E & T11E c/w Fan >08/15
WP-T10E/001B
Field Coil 115V T10EL & T11EL >10/09 to 07/15
WP-T10EL/002A
Field Coil 230V T10E & T11E >10/09 to 07/15
WP-T10E/002A
Field Coil 115V T10EL & T11EL >08/15
WP-T10EL/002B
Trend Coil 230V T10E & T11E >08/15
WP-T10E/002B
Switch
WP-T10E/003
Carbon Brush 115V (1 pair) <10/09
WP-T10EL/004
Carbon Brush 240V (1 pair) <10/09
WP-T10E/004
Carbon Brush 115V (1 pair) T10EL & T11EL >10/09 WP-T10EL/004A
Carbon Brush 240V (1 pair) T10E & T11E >10/09
WP-T10E/004A
2 Core Cable Only 115V UK T10L & T11L
WP-T10L/005
2 Core Cable with Plug 230V UK T10 & T11
WP-T10/005
2 Core Cable with Plug 230V Euro T10&T11/EURO WP-T10EUR/005
Brush Holder <10/09
WP-T10/006
Brush Holder >10/09
WP-T10/006A
Top Vent Housing
WP-T10/007
Field Housing <07/15
WP-T10/008
Field Housing >08/15
WP-T10/008A
Lead Field to Brush 115V (Yellow x 95mm) <07/15 WP-T10L/009
Lead Field to Brush 230V (Yellow x 175mm) <07/15 WP-T10/009
Lead Field to Brush 115V (Yellow x 95mm) >08/15 WP-T10L/009A
Lead Field to Brush 230V (Yellow x 95mm) >08/15 WP-T10/009A
Lead Speed Control (Red x 100mm F90-M)
WP-T10/010
Switch Lever
WP-T10/011
Machine Screw Csk M4 x 6mm Phillips
WP-T10/012
Switch Slider
WP-T10/013
Brush Holder Clamp
WP-T10/014
Screw Self Tapping Pan 3.8mm x 12mm Phillips
WP-T10/015
Top Bearing 12 x 32 x 10mm 6201-2RSL <07/15
WP-T10/016
Top Bearing 8 x 22 x 7mm 608-2RS >08/15
WP-T10/016A
Circlip <07/15
WP-T10/017
Screw Self Tapping Dome 4mm x 25mm Phillips
WP-T10/018
Cable Guard 115V T10L & T11L
WP-T10L/019
Cable Guard 240V T10 & T11
WP-T10/019
Bolt Pan M5 x 68mm Phillips
WP-T10/020
Washer Split M5
WP-T10/021
Screw Self Tapping Pan 3.2mm x 13mm Phillips
WP-T10/022
Cable Clamp
WP-T10/023
Lead Switch to Field (Red x 95mm F-M)
WP-T10/024
For Armature & Field Coil T10E(L) & T11E(L) <10/09 see No.114.
-23-
T10 & T11
T10 & T11 - SPARE PARTS LIST
v5.0 04/2015
No. Qty.Desc.
26
27
28
29
30
31
32
33
35
36
37
38
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
64
65
66
67
68
1
1
1
4
1
2
1
1
1
1
1
1
1
1
2
1
1
1
6
1
1
1
1
1
1
1
1
2
1
1
1
1
3
1
1
1
1
2
2
1
1
1
1
5
Ref.
Depth Stop Support (Left Hand)
Depth Stop Support (Right Hand)
Depth Stop Lens
Screw Self Tapping Dome 3.8mm x 14mm PH
Half Nut Hex M12
Screw Self Tapping Dome 4.8mm x 63mm PH
Fan Baffle <07/15
Fan Baffle >08/15
Fan <07/15
Fan >08/15
Plunge Lock Lever
Spacer for Revolving Guide
Spring for Plunge Lever
Plunge Lever Bolt
Machine Screw Csk M8 x 35mm Phillips
Handle Left
Lower Bearing Housing T10
Lower Bearing Housing T11
Machine Screw Csk M4 x 8mm Phillips
Domed Nut Hex M12
Knurled Nut Outer
Depth Stop
Scale Label
Depth Stop Adjustment Knob
Handle Right
Depth Stop Locking Plate
Depth Stop Locking Knob
Spring for Depth Stop Nut
Washer 6.6mm x 12mm x 1.6mm
Slider for Depth Stop Nut
Bearing 25mm x 47mm x 12mm 6005-2RSLTN9
Spindle Lock Housing
Machine Screw Pan M4 x 8mm Phillips
Bearing Lock Nut
Collet 12mm (Europe)
Collet 12.7mm (UK & Eire)
Collet Nut
Plunge Spring
Plunge Spring Rod
Spring for Depth Stop
Depth Stop for Micro Adjustment Screw
Machine Screw for Revolving Guide
Threaded Pin M5 x 18mm
Nut Hex M5
-24-
WP-T10/026
WP-T10/027
WP-T10/028
WP-T10/029
WP-T10/030
WP-T10/031
WP-T10/032
WP-T10/032A
WP-T10/033
WP-T10/033A
WP-T10/035
WP-T10/036
WP-T10/037
WP-T10/038
WP-T10/040
WP-T10/041
WP-T10/042
WP-T11/042
WP-T10/043
WP-T10/044
WP-T10/045
WP-T10/046
WP-T10/047
WP-T10/048
WP-T10/049
WP-T10/050
WP-T10/051
WP-T10/052
WP-T10/053
WP-T10/054
WP-T10/055
WP-T10/056
WP-T10/057
WP-T10/058
CLT/T10/12
CLT/T10/127
CLT/NUT/T10
WP-T10/061
WP-T10/062
WP-T10/064
WP-T10/065
WP-T10/066
WP-T10/067
WP-T10/068
T10 & T11
T10 & T11 - SPARE PARTS LIST v5.0 04/2015
No. Qty.Desc.
69
70
71
72
73
74
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
98
101
102
103
104
105
106
107
109
110
111
112
113
Ref.
1
Threaded Pin M5 x 22mm
WP-T10/069
1
Washer Dished 6.35mm x 12.5mm x 0.5mm
WP-T10/070
1 Threaded Pin M5 x 35mmWP-T10/071
1 Revolving GuideWP-T10/072
1 Ball for Revolving GuideWP-T10/073
1 Spring for Revolving GuideWP-T10/074
1 Base Casting Complete T10WP-T10/078
1 Base Casting Complete T11WP-T11/078
1
Side Fence Micro Adjuster Scale
WP-T10/079
1
Phenolic Slider Base T10
WP-T10/080
1
Phenolic Slider Base T11
WP-T11/080
5
Spring for Thumb Knob
WP-T10/081
1
Side Fence Micro Adjuster Screw
WP-T10/082
1
Spindle Lock Spring
WP-T10/083
1
Guide Rods 10mm x 360mm (Pair)
ROD/10X360
5
Thumb Knob Male M6 x 15mm
WP-T10/085
2
Side Fence Cheek
WP-T10/086
1
Side Fence Complete T10
WP-T10/087
1
Side Fence Complete T11
WP-T11/087
4
Washer 5.5mm x 9.5mm x 1.0mm
WP-T10/088
1
Capacitor <10/09
WP-T10/089
1
Capacitor >10/09
WP-T10/089A
4
Washer Spring <07/15
WP-T10/090
1
Side Fence Bridge with Adjuster T10
WP-T10/091
1
Side Fence Bridge with Adjuster T11
WP-T11/091
1
Spindle Lock ButtonWP-T10/092
5
Machine Screw Pan M5 x 15mm Phillips
WP-T10/093
1
Speed Control Dial
WP-T10E/094
2
Machine Screw Csk M5 x 10mm Phillips
WP-T10/095
1
Magnet for Speed Control
WP-T10E/098
1
Spanner 22mm A/F
SPAN/22
1
Side Fence Body
WP-T10/102
1
Speed Control Board 115V T10EL &T11EL
WP-T10EL/103
1
Speed Control Board 230V T10E &T11
WP-T10E/103
3
Washer Split Spring M4
WP-T10/104
1
Lead Switch to Speed Control (Red x 110mm F-F)
WP-T10/105
1
Lead Switch to Speed Control (Red x 105mm M/F-F) WP-T10/106
1
Dust Spout T10
WP-T10/107
1
Dust Spout T11
WP-T11/107
1
Dust Spout Clip
WP-T10/109
1
Dust Spout Retaining Clip
WP-T10/110
2
Machine Screw Pan M5 x 12mm Slot
WP-SCW/42
1
Screw Self Tapping Pan 4mm x 32mm Phillips
WP-T10/112
1
Spacer
WP-T10/113
-25-
T10 & T11
T10 & T11 - SPARE PARTS LIST v5.0 04/2015
No. Qty.Desc.
114
117
118
119
120
121
123
FOR T11
124
124A
125
125A
126
127A
128
129
130
Ref.
0
0
1
1
1
2
2
1
1
Armature Kit 115V <10/09 T10EL & T11EL
Armature Kit 230V <10/09 T10E & T11E
Manual T10 & T11
Inner Plate T10
Inner Plate T11
Machine Screw Csk M5 x 8mm Slot
Machine Screw Cheese M5 x 8mm Slot
Line up Pin 12mm & 1/2”
Guide Bush 30mm x 10mm
WP-T10EL/AK
WP-T10E/AK
MANU/T10
WP-T10/075
WP-T9/075
WP-SCW/09
WP-SCW/98
WP-T9/090
GB30/A
1
1
2
2
1
2
1
2
0
Stud for Table Height Adjustment T11 <10/05
Stud for Table Height Adjustment T11 >11/05
End Cap Hex for Stud T11 <10/05
End Cap Hex for Stud T11 >10/05
Barrel Nut for Table Height Adjustment T11
Hi-tensile 8.8 Machine Screw for Hex Nut >10/05 T11
Table Fine Height Adjuster T11
Sintered Bush for Table Height Adjustment T11
Stud and Hex Conversion Kit <10/05
WP-T11/124
WP-T11/124A
WP-T11/125
WP-T11/125A
WP-T11/126
WP-T11/127A
WP-T11/128
WP-T11/129
WP-T11/130
SERVICE NOTE
FOR T11 PRE (<) OCT 2005
Pre Oct 2005 T11 Quick Raiser shaft hex nuts
are factory set. The bottom (base) hex nut and
top hex nut are both permanently glued and
tightened to a torque of 22Nm. To remove hex
nuts, ensure a socket is used on each end of the
shaft. Remove top hex nut first.
Please note:
The shaft has been designed to have a
1.2mm float in the sintered bushes.
Please contact Trend Customer Services for
further information.
When servicing the tool, please ensure the
correct adhesive and torque setting is used.
FOR T11 POST (>) OCT 2005
Post Oct 2005 T11 has a splined Quick Raiser
shaft and hex nuts. The hex nuts are held by
Hi-tensile 8.8 class Torx® machine screws which
have been permanently glued with Locktite® 270
and tightened to torque 2.1Nm to 2.5Nm.
When servicing the tool, please ensure the
correct adhesive and torque setting is used.
-26-
T10 & T11
T10 & T11 - SPARE PARTS DIAGRAM
v5.0 04/2015
Please use only Trend original spare parts.
INAL
ORIG TIONS
RUC
INST
118
9
Armature Kit - post Oct 2009
Nos. 1, 2, 3, 4, 6, 89
-27-
114
T10 & T11
T11 Fine Height Adjuster Fitting Hole Position
CL
CL
36mm
Actual Size
Ø 20mm
68mm
Check this scale to a rule to
ensure actual size, before use
as a drilling template.
Actual Size
0 102030405060708090100
-28-
MANU/T10 v6.0
RECYCLABLE
Trend Machinery & Cutting Tools Ltd.
Odhams Trading Estate St Albans Road
Watford WD24 7TR England
Tel: 0044(0)1923 249911
technical@trendm.co.uk
www.trend-uk.com
© Copyright Trend 2013, 2015, 2017. No part of this publication may be reproduced, stored or transmitted in any form without prior
permission. Our policy of continuous improvement means that specifications may change without notice. Trend Machinery and Cutting
Tools cannot be held liable for any material rendered unusable or any form of consequential loss. E&OE
N563304 10/17
® All registered trademarks acknowledged.
Download PDF
Similar pages
TRENpage 103
Specifications
Specifications
Olfa RTY-1/DX User's Manual
STEP 1:
CAPD247-347 Screen preliminary 120110
104814
null 9899508