Manual Thermostat Instructions

Model Number: HWTH2 Manual
3 “Manu”
4 and
1 Press
indicates
manual
mode,
indicates
automatic
In
the
room
This
feature
is used
tomode.
compensate
for any difference
2 Calibrate
3to save
(6).
OK
exit. temperature.
Indicates
the“Auto”
time frames
available
in Auto
Mode.
-5°C ~ +5°C
0°C
between the displayed room temperature and a thermometer.
Key Lock & Unlock
Manu Auto mode,
thermostat
executes
theFTpreprogrammed
schedules.
RT/FT RT
stands forthe
“room
temperature”
and
stands for “floor
temperature”.
Calibrate
the
floor
temperature.
This
feature
is
used
to
compensate
for
any
difference
you set your thermostat to 5+2 day programmable mode
Press and hold
to lock 0°C
the thermostat. A lock -5°C
icon will
display.
~ +5°C
Auto If Heating
mode,
the thermostat maintains a constant set temperature
isManu
turned
4 While in
between
theondisplayed floor temperature and a thermometer.
Press and hold
to unlock the thermostat. The lock icon will disappear.
(1).manually
Press Prog
button.
set
by
the
user.
“Manu” indicates manual mode, “Auto” indicates automatic mode. In
Manual
(2).
up the
or down
buttons to readout(AF
adjust the timemodel
you wish
the program
1 event
to commence
no air
program changes are
unit to
is locked.
temperature
only).
This gives
option
to choose *toNote
show
A possible while the A=
5 PressSet
show air temperature,
r from Monday to Friday). and then press Prog button.
Manu for the week days(
temperature,floor
temperature or to show both floor & air in interval.
F=to show floor temperature,
Manu
mode,
the to
thermostat
maintains
constant
set temperature
Pressinup
or down
buttons
set the temperature
for athis
time period,then
press Prog.
Auto(3).While
Temporary temperature override
A - F = to show both in 5 second intervals
(4).manually
Set time set
and by
temperature
the user.for the next time period. Repeat step(2) and (3) for each
In Auto mode, to temporary override the current setpoint temperature,
time period. and then press Prog button.
6 PressSet
Presssurface.
up or down button40
once,
floorbuttons
temperature
only).
This feature
is to
tocommence
protect the1.floor
20°Cflashing.
~ 40 °C
(5).
up the
or down
to adjustlimit(AF
the timemodel
you wish
the program
1 event
°C the set temperature starts
2. Press up or down button again to adjust the set temperature.
for the weekends( Saturday and Sunday). and then press Prog button.
Turning
your
heating
On
Manually:
3.
Press
OK
button
to
confirm
the
setting
with
OVERRIDE
shown.
(6). Press
up or down buttons to set the temperature for this time period,then press Prog.
Menu
Settings
Now your thermostat will maintain the new set temperature until the next setpoint.
(7).
Set power
time
andbutton
temperature
theyour
next thermostat.
time
period.
Press
to turnforon
°C or
°F. Repeat step(5) and (6) for each
Select
temperature
format
°C / °F
7 the
°C press Del button once.
To cancel the override setting,
To access
settings,
timeMenu
period.
Press
the
Mode
button
until
the
screen
shows
manual.
”.
(8). Press OK to save and exit.
8 the
1.Press
Press
Power
offadjust
the thermostat.
12 /to
24turn
hour
clock
12 / 24
upSelect
orbutton
down
button
to
to the required temperature
24
2.Around
Press 23degC
and holdisPower
buttonbut
foryou
three
up the configuration menu. Resetting
Now press factory
power button
to select each different menu number
.
defaults
an average
canseconds
increasetoifbring
required.
Your
thermostat has the ability
factory
9Key
OFF to reset all settings to theON
&protection.
Unlock
featuretoisthetoambient
avoid room
temperature goes below
5 °C
/ OFFdefaults. If you
Press
the Lock
okFrost
button.
The reading This
will return
temperature
are certain you want to do this:
standby mode(when thermostat is turned off), press and hold Clock button and
Press and
hold typetoselection.
lock the thermostat.
A lock
icon
will display.
Thisongives
user
2 options
of program
type.(5+2 or 7 dayInprogrammable)
ure
Flame Program
icon should
now be shown
screen
Day button for
5 seconds until --:-- is shown(shown
for 5 seconds only)
Factory
Adjustment
Menu #
5+2
day
willtogive
you the
5 days(Monday
to Fiday)
withwill
thedisappear.
same four events(Wakeup, out,
Press and
hold
unlock
thermostat. The
lock icon
Feature
Explanation
default
(Press up & down
to adjust)
01buttons
= 5+2 day
programmable
01
home,sleep)
and 2are
days(Saturday
with the same four events.
* Note no
program changes
possible whileand
the Sunday)
unit is locked.
02 = 7 day programmable
10
number
degrees
difference
before
switching
7 day will give you individualThe
settings
forofeach
day from
Monday
to Sunday.
Temporary
temperature
overrideThe default is 1Deg C which means the stat will
Turning
your heating
Off Manually:
Australia
New Zealand
switch
the
heating
on
0.5DegC
below
the
set
Verve Distribution
The Heating Company
Press Power button to turn off your thermostat, you will see OFF on LCD.
Todd
St
PO BOX 420
In Auto mode, to temporary override the
current setpoint
temperature
and willtemperature,
turn it off 0.5DegC above the
1 Deg6Port
C
-Adelaide
5 Deg
C
SA 5015
Whitianga NZ
1 DegC
011. thermostat
differential
Your
floor
are both
and
floor will starts
cool
down.
Any
Press Switching
up orand
down
button
once,offthe
setyour
temperature
flashing.
set temperature.
www.vervedistribution.com.au
www.hotwire.co.nz
2. Press
or down
button
again
to adjust
With athe
2 set
DegC
differential the heating will switch
settings
youup
have
entered
into the
Thermostat
will
be temperature.
maintained
3. Press OK button to confirm the setting
OVERRIDE
shown.
onwith
1 DegC
below the
set temperature and will
Now
your thermostat will maintain the new
set off
temperature
until the
setpoint.
switch
1 DegC above
thenext
set temperature.
Power Supply:
N
N
L L
To cancel the override setting, press Del button once.
220Vac +10%, 50/60Hz
0DegC
02
Temp Calibration
This is to recalibrate the temp if required
-5 Deg C - + 5 Deg C
Menu Settings
Sensor selection. This thermostat is a combination model allowing you to choose
Resetting
defaults
Adjust the set
temperature
between
3Switching
different models.
(A, AF,F,)
differential.
The numbers of degree difference
before factory
switching.
The default is
1
A / AF
/ F In standby
onl y ,means
A model:1°Cair
with built
sensor
Youron
thermostat
has thethe
ability
defaults.
which
thein thermostat
will switch the heating
0.5°C below
settoA reset all settings to the factory
1. Press up or down
button
once,
the
set
temperature
starts
flashing.
AF model: air & floor , with both built in and remote sensor
1°C
temperature
and
will
turn
it
off
0.5°C
above
the
set
temperature.
mode(when
thermostat
is
turned
off),
press
and
hold
Up
button
and
Down
F model: again
floor to
onladjust
y , with
remote
sensor
2. Press up or down
the
setrequired
temperature.
to the
temperature.
2 buttonWith
a 2°C differential, the heating will switch on 1°Cbutton
below
the set temperature
for 5 seconds until --:-- is shown(shown for 5 seconds only)
3. Wait for 5 seconds
to
confirm
the
setting.
Switching differential.
and will switch
off 1°Cofabove
set temperature.
The numbers
degreethe
difference
before switching. The default is
1°C which
means the
will switch the heating on 0.5°C below the set
Now your thermostat
will maintain
thethermostat
new set temperature.
2
3
4
5
3temperature
1°C
Calibrate
temperature.
This
feature is used to compensate for any difference
and will the
turn room
it off 0.5°C
above the set
temperature.
thethe
displayed
room
temperature
and
thermometer.
With a 2°Cbetween
differential,
heating will
switch
on 1°C below
theaset
temperature
and will switch off 1°C above the set temperature.
Calibrate the floor temperature. This feature is used to compensate for any difference
4
between
the displayed
temperature
and a thermometer.
Calibrate
the
room temperature.
Thisfloor
feature
is used to compensate
for any difference
Set the temperature readout(AF model only). This gives option to choose to show air
temperature,floor temperature or to show both floor & air in interval.
10
N
L L
2
N
N
L L
New Zealand
Australia
The Heating
Company
Verve Distribution
6 Todd St
International
Port Adelaide SA 5015
PO Box 420
www.vervedistribution.com.au
Whitianga NZ
www.hotwire.co.nz
New Zealand
The Heating Company
PO BOX 420
Whitianga NZ
Line from switch box
Storage: -20~50 deg C
Deg C / Deg F
Brown wire from element
LOAD (16A)
floor 5~40 deg C
20°C ~ 40 °C
40 °C
°C / °F
24
Manual
12 / 24
24
OFF
This feature is to avoid room temperature goes below 5 °C
OFF
ON / OFF
Program
typeThis
selection.
gives
user 2 options
type.(5+2 or 7 day programmable)
gives user 2This
options
of program
type.(5+2oforprogram
7 day programmable)
Program type
selection.
5+2
give you 5 days(Monday
Fiday)
the same four
5+2 day will
giveday
youwill
5 days(Monday
to Fiday) with thetosame
fourwith
events(Wakeup,
out, events(Wakeup, out,
home,sleep)
and 2 days(Saturday
and Sunday) with
theSunday)
same fourwith
events.
home,sleep)
and 2 days(Saturday
and
the same four events. 01
10
7 day will 7give
individual
settings
for each
day from
to Sunday.
dayyouwill
give you
individual
settings
forMonday
each day
from Monday to Sunday.
1
LOAD (16A)
4
L
N
5
01 =
015+2 day programmable01 =
02 = 7 day programmable 02 =
6
L
Power Supply:
220Vac +10%, 50/60Hz
Power Supply:
N
Floor Sensor
Floor Sensor
(Cables can goFEED
either side)
230 VAC
3
40 °C
°C
This feature is to avoid room temperature goes below 5 °C
Frost protection.
-5
°C
box and
it with
provided. To replace the thermostat put the top
8 tighten
Select
12 /the
24 screws
hour clock
into the backing plate and then push the bottom of the thermostat in. Then replace
9
0°C
F=to show floor temperature,
A - F = to show both in 5 second intervals
Select 12 / 24 hour clock
9
Frost
protection.
screw holding both parts
together.
-
A= to s
F=to sh
A - F = to sh
A= to show air temperature,
6
Set the floor temperature limit(AF model only). This feature is to protect the floor surface.
0°C
A ~ +5°C
-5°C
A
Using a screwdriver
unscrew
the front plate
from the
back
°C or
°F. plate. Then pull
Select temperature
format
7
the bottom Select
of thetemperature
thermostat format
towards°Cyou
off
the
back
plate. Wire up the
or °F.
7
thermostat as8per the wiring diagram below, then place the back plate into the flush
220Vac +10%, 50/60Hz
Floor Sensor
(Cables can go either side)
FEED
LOAD (16A)
230 VAC
230/240
VAC
LOAD (16A)
www.hotwire.co.nz
Connect green wire from the
element to the house earth
Load Capability: <16 A, 220VAC
Accuracy:
1deg C
Load 5~30
Capability:
Set-point range: ambient
deg C <16 A, 220VAC
Accuracy:
floor
5~40 deg C 1deg C
range:
Storage: -20~50 degSet-point
C
FEED
230/240 VAC
1
-5°C ~ +5°C
temperature,floor temperature or to show both floor & air in interval.
Set the floor temperature limit(AF model only). This feature is to protect the floor surface.
Installation Instructions
6
1°C ~ 5°C
0°C
between the displayed room temperature and a thermometer.
Calibrate
the
floor
temperature.
This
feature
is
used
to
compensate
for
any
difference
Set the temperature readout(AF model only). This gives option to choose to show
5
0°C air
between the displayed floor temperature and a thermometer.
Blue wire from element
230 VAC
Press up o
+
-
Resetting factory defaults
This allows the temperature to be set to show
has the
ability to reset all settings to the factory defaults. If you
Load Capability: <16
C A, 220VAC
03Your thermostat
Temperature
Format
Deg Celsius or Deg Fahrenheit
are certain you wantFloor
to doSensor
this:
1deg C
In standby mode(when thermostat is turned off), press and hold Clock button Accuracy:
and
Day button forFEED
5 seconds until --:-- is shown(shown for 5 seconds only)
Set-point range: ambient 5~30 deg C
Factory Default
Feature Value
Feature Description
Menu #
Press Power
buttton to turn off the thermostat.
Key Lock & Unlock
Buttons
and Descriptions
Sensor
is a combination
model
allowing
to choose
Press and hold button Prog
for 3selection.
seconds toThis
bringthermostat
up a configuration
menu. Now press
Prog
button toyou
select
different menu number.
Press and hold up button to lock the thermostat. A lock icon will display.
Power button, to turn on/off thermostat
between 3 different models. (A, AF,F,)
Press
and
hold
down
button
to unlock the thermostat. The unlock
1
A icon will dissapear.
model:
air will
onllock
Up button, Also a longApress(5
seconds)
the keypad
y , with
built in sensor
AF model:
air & floor
, withtheboth
built in and remote
sensor
* Note
no program changes
are Default
possible while Press
the unitup
is or
locked.
Factory
Down
Also a Description
long
press(5 seconds)
will unlock
keypad
down button to select
Feature
Menu
# button,
Feature Value
F model: floor onl y , with remote sensor
House Neutral
2 Press OK button to exit.
Press and hold button Prog for 3 seconds to bring up a configuration menu. Now press Prog button to select different menu number.
If you set your thermostat to 5+2 day programmable mode
3
Step Two: Set the thermostat to Auto mode
(1). Press Prog button.
4 Confirm button
Ensure that
the thermostat
is on Auto mode. To select Auto use the mode button (2). Press up or down Factory
buttons to Default
adjust the time you
wishup
theor
program
event toto
commence
Press
down1button
select
Feature
Description
Menu
#the clock
5 Set
Value
for the week days( Feature
from Monday
to Friday). and then press Prog button.
Step
Three:
Programming
your
schedules
6 Set the Sensor
day of the
week This thermostat is a combination model allowing you to
selection.
(3).choose
Press up or down buttons to set the temperature for this time period,then press Prog.
thermostat
to 7 day
programmable
between
3 different
models.
(A, AF,F,)mode
(4). Set time and temperature for the next time period. Repeat step(2) and (3) for each
7 If you set your
1
A
A / AF / F
A model: air onl y , with built in sensor
time period. and then press Prog button.
button. air & floor , with both built in and remote sensor
8 (1). Press Prog
AF model:
(5).
Press
up
or
down
buttons
to
adjust
the
time
you
wish
the
program
1 event to commence
F model:
floortoonl
y , withdayremote
sensor
Press button,
up
or down
buttons
you wish
to start programming. then press Prog.
9 (2).Power
to turn
on/offselect
the the
thermostat
for the weekends( Saturday and Sunday). and then press Prog button.
(hold up button to select all days of the week, to cancel, hold up button again.)
up oris down buttons to set the temperature for this time period,then press Prog.
Switching
The
numbers
ofwish
degree
difference
before
switching.(6).ThePress
default
+ (3).UpPress
button.
Also
a differential.
long
press
(5 seconds
) will
lock
keypad.
up or
down
buttons
to adjust
the time you
thethe
program
1 event
to commence
Set time and temperature for the next time period. Repeat step(5) and (6) for each
which
theand
thermostat
will
switch
the heating
on
0.5°C below (7).
the set
4means
1for the
2 1°C
3
currently
selected
day.
then
press
Prog
button.
Indicates
the
time
frames
available
inthe
Auto
Mode.
- Down
button.
Also
a
long
press
(5
seconds
)
will
un
lock
keypad.
1°C
1°C ~ 5°C
temperature and will turn it off 0.5°C above the set temperature.
time period.
(4).
up or down buttons
to set the temperature
for this
period,then
press Prog.
RTPress
stands
temperature”
and FT stands
fortime
“floor
temperature”.
RT/FT
2Power
button,
to turn
on/off thethe
thermostat
Withfora “room
2°C
differential,
heating
will switch
on 1°C
below the set temperature
(8). Press OK to save and exit.
(5). Set time and temperature for the next time period. Repeat step(2) and (3) for each
and
will
switch
off
1°C
above
the
set
temperature.
Heating
is turned on
time period.
Press Power buttton to turn off the thermostat.
Press and hold button Prog for 3 seconds to bring up a configuration menu. Now press Prog button to select different menu number.
Line from switch box
buttons down will increase or decrease the time in 15 minutes increments.
Press the OK button once the time is set.
Button
and Descriptions
Menu Settings
Press
the day
button to get to the current Day of the week.
1
Program
button
Button
and Descriptions
Press Power
buttton to turn off the thermostat.
HotwireThermostat
Instructions
House Neutral
Use the up and down buttons to adjust .Holding the
Menu Settings
Blue wire from element
Hotwire Thermostat
Instructions
HotwireThermostat
Instructions
(2). Press up or down buttons to select the day you wish to start programming. then press Prog.
(hold up button to select all days of the week, to cancel, hold up button again.)
(3). Press up or down buttons to adjust the time you wish the program 1 event to commence
for the currently selected day. and then press Prog button.
(4). Press up or down buttons to set the temperature for this time period,then press Prog.
(5). Set time and temperature for the next time period. Repeat step(2) and (3) for each
time period.
(6). Press OK to save and exit.
Press clock button, and time display will start flashing
Brown wire from element
(1). Press Prog button.
Step One: Set The Time and Day:
floor 5~40 deg C
Storage: -20~50 deg C