MSPWLKTA1000B INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Grommet Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
MSP-WLKTA1000B
MSP-WLKTA1000B
Installation Instructions
DISCLAIMER
Milestone AV Technologies, Inc., and its affiliated corporations
and subsidiaries, intend to make this manual accurate and
complete. However, Milestone makes no claim that the
information contained herein covers all details, conditions or
variations, nor does it provide for every possible contingency in
connection with the installation or use of this product. The
information contained in this document is subject to change
without notice or obligation of any kind. Milestone makes no
representation of warranty, expressed or implied, regarding the
information contained herein. Milestone assumes no
responsibility for accuracy, completeness or sufficiency of the
information contained in this document.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the MSP-WLKTA1000B up
to (and including) the display does not exceed 120 lbs
(54.43 kg).
•
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
DIMENSIONS
5.00
4.43 MAX DEPTH
4.00
2
The weight capacity of the MSP-WLKTA1000B may be
LIMITED to the lowest weight capacity of any other
component located between the MSP-WLKTA1000B
and the supporting structure!
Installation Instructions
MSP-WLKTA1000B
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Marcar con lápiz
Befestigungsteil festziehen
Stiftmarkierung
Apertar fixador
Marcar com lápis
Serrare il fissaggio
Segno a matita
Bevestiging vastdraaien
Potloodmerkteken
Serrez les fixations
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Perforar
Befestigungsteil lösen
Bohrloch
Desapertar fixador
Fazer furo
Allentare il fissaggio
Praticare un foro
Bevestiging losdraaien
Gat boren
Desserrez les fixations
Percez un trou
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
TOOLS REQUIRED FOR INSTALLATION
1/2"
9/16"
PARTS
B (1)
A (1)
C (1)
3/8" x 6"
3
MSP-WLKTA1000B
Installation Instructions
INSTALLATION
IMPORTANT ! : If the display being installed has a
recessed mounting surface, the display must be
assembled to the mount prior to mount installation.
WARNING: ELECTRICAL SHOCK HAZARD! Drilling into
electrical wires and cables can cause DEATH or SERIOUS
PERSONAL INJURY! ALWAYS make certain area under
mounting surface is free of electrical wires and cables before
drilling.
WARNING: EXPLOSION AND FIRE HAZARD! Drilling
into gas plumbing can cause DEATH or SERIOUS
PERSONAL INJURY! ALWAYS make certain area under
mounting surfaces is free of gas, water, waste, or any other
plumbing before drilling.
1.
Determine approximate location for mount keeping in mind
display size, extension, height adjustment (if applicable),
and pitch/roll requirements.
NOTE: The mounting surface may have a maximum depth of
4.43".
2.
Mark installation location and drill one 1/2" dia. pilot hole
through mounting surface. (See Figure 1)
3.
Position grommet mounting bracket (B) underneath
mounting surface and grommet (A) on top of mounting
surface and align mounting holes with pilot hole.
(See Figure 1)
4.
Align mounting hole in bottom of pole with mounting hole in
grommet (A) and secure to mounting surface using one
3/8-16 x 6" hex head bolt (C). (See Figure 1)
(A)
1/2" x1
2
Mounting
Surface
(B)
4
Figure 1
4
(C) x1
MSP-WLKTA1000B
Installation Instructions
USA/International
Europe
Asia Pacific
8832-000248
2008 Chief Manufacturing
www.chiefmfg.com
03/08
A
P
F
A
P
F
A
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
P +86-755-8996 9226
F +86-755-8996 9217